Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Infra Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹26.7 L
EMD Value
₹53,400
Closing Date
9 Sept 2024, 5:30 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Facilities Management Division, Bangalore
HINDUSTAN AERONAUTICS LIMITED Facilities Management Division, Bangalore
Renovation of HR Dept. in Overhaul Division, HAL BC.
8457
TENDER NOTICE/NCP/15/24-25/02
Works
Contract Section Civil-FMD-Bangalore
₹0
₹53,400
9 Sept 2024
11 Jul 2024
11 Jul 2024
9 Sept 2024
HINDUSTAN AERONAUTICS LIMITED BANGALORE FACILITIES MANAGEMENT DIVISION
NAME OF THE WORK: “Renovation of HR Dept. in Overhaul Division, HAL [BC]." CONTRACT NO. HAL/FMD/R-107A/23-24
Name of the Tenderer:
Sl. No Specification Quantity Unit Rate in Figs [Excluding GST] Rate in words Amount
Preamble: (1) The subject work has been called on works contract basis and prevailing GST for same is 18%. Any change in GST +/- during the currency of contract shall be on HAL account. The tenderer shall abide by prevailing GST act. (2) This BOQ specifications have to be read in conjunction with detailed technical specification and tender drawings if any. (3) The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered. (4) The quoted percentage for the works mentioned below, shall be taken into consideration for evaluation of the tender. The lowest offer (L-1) will be determined considering the total amount including GST based on the quoted percentage.
PART - 'A' - CIVIL WORKS
1 Demolishing brick work built in cement mortar, manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead, etc., all complete as directed by Engineer-in-Charge. 5.00 Cu m 0.00
2 Demolishing cement concrete of nominal 1:4:8 or leaner mix manually / by mechanical means including disposal of material within 50 metres lead, etc., all complete as directed by Engineer-in-Charge. 1.00 Cu m 0.00
3 Dismantling tile work in floors and roofs (for thicknes of tiles 10mm to 25mm) laid in cement mortar including stacking material within 50 metres lead, etc., all complete as directed by Engineer-in-Charge. 75.00 Sq m 0.00
4 Dismantling of old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50meters lead, etc., all complete as directed by Engineer-in-Charge. 50.00 Sq m 0.00
5 Disposal of moorum / building rubbish / malba / similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead up to 10km for all lifts complete as per direction of engineering in charge. Note : Item to be applicable in urban areas having direction for restricted hours for movement/plying of laod carrying motor vehicke of 3.5 cum or more, etc., all complete as directed by Engineer-in-Charge. 6.00 Cu m 0.00
6 Dismantling of doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfast, etc complte and stacking within 50m lead of area 3 sqm and below, etc., all complete as directed by Engineer-in-Charge. 2.00 Each 0.00
7 Cutting holes up to [30 x 30]cm in walls including making good at the same. With common brick burnt clay FPS(non modular ) bricks, etc., all complete as directed by Engineer-in-Charge. 3.00 Each 0.00
8 Brick work in Cement mortar 1:4 (1 cement : 4 coarse sand) with common burnt clay F.P.S. (non modular) bricks class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes, etc., all complete as directed by Engineer-in-Charge. 2.00 Cu m 0.00
9 Half brick masonry in Cement mortar 1:3 (1 cement : 3 coarse sand) with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level, etc., all complete as directed by Engineer-in-Charge. 25.00 Sq m 0.00
10 Providing and laying plaster mix 1: 6 ( 1 cement : 6 coarse sand) of 20mm thick plaster on the rough side of single or half brick wall, etc., all complete as directed by Engineer-in-Charge. 100.00 Sq m 0.00
11 Providing and laying plaster mix 1: 3 ( 1 cement :3 coarse sand) finished with flaoting coat of neat cement (20mm thick cement plaster), etc., all complete as directed by Engineer-in-Charge. 30.00 Sq m 0.00
12 Providing and laying cement concrete(1:2:4-1 Cement : 2 coarse sand (zone-III) including manufactured sand derived from Recycled Concrete Aggregate (RCA) upto 25% : 4 graded stone aggregate 20 mm nominal size including Recycled Concrete Aggregate (RCA) upto 25%) in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing, etc., all complete as directed by Engineer-in-Charge. 1.00 Cu m 0.00
13 Providing wood work in frames of doors,windows,c;erestory windows and other frames wrought framed and fixed in position with hold fast lugs or with dash fasterners of required dia and length (hold fast lugs or dash fasterner shall be paid for separtely: Second class teak wood, etc., all complete as directed by Engineer-in-Charge. 0.08 Cu m 0.00
14 Providing 40x5mm flat iron hold fast 400mm long including fixing to frames with 10mm dia bolts,nuts and wooden plugs and embeddding in cement concrete block 300x100x150mm 1:3:6(1 cement:3 coarse sand:6 Graded stone aggreagtes 20mm nominal size), etc., all complete as directed by Engineer-in-Charge. 8.00 Nos 0.00
15 Providing and fixing ISI marked flush door shutters conforming to IS :2202(Part-I) Decorative type,core of block construction wit frames of 1st class hard wood and well matched teak 3 ply veenering with vertical grains or cross bands and face veneers on both sides of shutters, 30mm thick including ISI marked Stainless Steel butt hinges with necessary screws, etc., all complete as directed by Engineer-in-Charge. 4.20 Sq m 0.00
16 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/Chowkhat of size 45x85mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. 32.00 R m 0.00
17 Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter 30mm thick of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) 12.00 Sq m 0.00
18 Providing and Fixing IS 12817 marked stainless steel butt hinges of size 125x64x1.90mm with stainless steel screws, etc., all complete as directed by Engineer-in-Charge. 6.00 Nos 0.00
19 Providing and Fixing of alumnium sliding door bolts 300x16mm size ,ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) tranparent or dyed to required colour or shade with nits and screws, etc., all complete as directed by Engineer-in-Charge. 6.00 Nos 0.00
20 Providing and Fixing alumnium tower bolts 250 x10mm size , ISI marked ,ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) tranparent or dyed to required colour or shade with nits and screws, etc., all complete as directed by Engineer-in-Charge. 12.00 Nos 0.00
21 Providing and Fixing alumnium handles 125mm long , ISI marked ,ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) tranparent or dyed to required colour or shade with nits and screws, etc., all complete as directed by Engineer-in-Charge. 12.00 Nos 0.00
22 Providing and Fixing alumnium hanging Single rubber floor door stopper , ISI marked ,ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) tranparent or dyed to required colour or shade with nits and screws, etc., all complete as directed by Engineer-in-Charge. 2.00 Nos 0.00
23 Providing and fixing bright finished brass 100mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 )alumnium lever handles of approed quality with necessary screws, etc., all complete as directed by Engineer-in-Charge. 2.00 Nos 0.00
24 Providing and Fixing alumnium extruded section body tubular type universal hydralic door closer (having brand logo with ISI mark) embosed on the body, door weight up to 36kgs to 80 kg and door width from 701mm to 1000mm) with double speed adjustement with necessary accessories and screws, etc., all complete as directed by Engineer-in-Charge. 2.00 Nos 0.00
25 Providing and fixing ISI marked oxidised MS door latches of size 300x20x6mm conforming to IS 5930 with screws etc complte.(copper oxidised as per IS 1378), etc., all complete as directed by Engineer-in-Charge. 6.00 Nos 0.00
26 Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, etc., all complete as directed by Engineer-in-Charge. 400.00 Kgs 0.00
27 Providing and fixing Powder coated aluminium(min thickness of powder coating 50 microns) work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : 80.00 Kgs 0.00
28 For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever requiredincluding the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15), etc., all complete as directed by Engineer-in-Charge. 70.00 Kgs 0.00
29 Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg/sqm ), etc., all complete as directed by Engineer-in-Charge. 40.00 Sq m 0.00
30 Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments, etc., all complete as directed by Engineer-in-Charge. 25.00 Sq m 0.00
31 Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade, etc., all complete as directed by Engineer-in-Charge. 100.00 Sq m 0.00
32 Providing and applying white cement based wall care putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth, etc., all complete as directed by Engineer-in-Charge. 800.00 Sq m 0.00
33 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre, etc., all complete as directed by Engineer-in-Charge. 800.00 Sq m 0.00
34 Removing dry or oil bond distemper ,water proofing cement paint and the like by scrapping ,sand papering and preparing the surface smooth including necessary repairs to scratches, etc., all complete as directed by Engineer-in-Charge. 450.00 Sq m 0.00
35 Removing white or clour wash by scrapping and sand papering and preapring the surfcae smooth including necessary repairs to scratches, etc., all complete as directed by Engineer-in-Charge. 350.00 Sq m 0.00
36 Wall painting Two coats with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour, etc., all complete as directed by Engineer-in-Charge. 350.00 Sq m 0.00
37 Distempering one or more coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour, etc., all complete as directed by Engineer-in-Charge. 450.00 Sq m 0.00
38 Painting 2 or more coats with synthetic enamel paint of approved brand and manufacture to give an even shade, etc., all complete as directed by Engineer-in-Charge.
a) one or more coats on old work 100.00 Sq m 0.00
b) Two or more coats on new work 20.00 Sq m 0.00
c) Applying red oxide zinc chromite primer of approved brand and manufacturer on steel work. 120.00 Sq m 0.00
39 French spirit polishing one or more coats on old work, etc., all complete as directed by Engineer-in-Charge. 200.00 Sq m 0.00
40 Finishing with epoxy paint( two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat,preparation of surface. etc., on concrete surface, etc., all complete as directed by Engineer-in-Charge. 100.00 Sq m 0.00
41 Providing and Fixing water closet squatting pan(indian type W C pan) with 100mm sand cast iron P or S trap ,10 litrs low level white PVC flushing cistern including flush pipe with manually controlled device (hand lever) confirming to IS:7231 with all fittings and fixtures complte including cutting and making good the walls and floors wherever required. Vitreous chine orissa pattern WC pan size 580x440mm with intergral type foot rests, etc., all complete as directed by Engineer-in-Charge. 3.00 Each 0.00
42 Providing and Fixing water closet squatting pan(European type W C pan) with 100mm sand cast iron P or S trap ,10 litrs low level white PVC flushing cistern including flush pipe with manually controlled device (hand lever) confirming to IS:7231 with all fittings and fixtures complte including cutting and making good the walls and floors wherever required. Vitreous chine orissa pattern WC pan size 580x440mm with intergral type foot rests, etc., all complete as directed by Engineer-in-Charge. 3.00 Each 0.00
43 Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth.: Granite stone of Approved shade 1.50 Sq m 0.00
44 Providing and fixing white Vitreous china wash basin size 550x400mm with C.I. brackets, 15 mm C.P. brass pillar tap, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required, etc., all complete as directed by Engineer-in-Charge. 4.00 Nos 0.00
45 Providing and Fixing brass bib cock of approved quality - 15mm nomnal bore, etc., all complete as directed by Engineer-in-Charge. 3.00 Nos 0.00
46 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms, etc., all complete as directed by Engineer-in-Charge. 4.00 Nos 0.00
47 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931, etc., all complete as directed by Engineer-in-Charge. 5.00 Each 0.00
48 Providing and fixing 8mm dia CP /SS jet with flexible tube up to 1 meter long with SS triangular plate to Eureopean type WC of quality and make, etc., all complete as directed by Engineer-in-Charge. 3.00 Each 0.00
49 Providing and fixing P.V.C. waste pipe (Semi regid pipe 32mm dia)for sink or wash basin including P.V.C. waste fittings, etc., all complete as directed by Engineer-in-Charge. 8.00 Nos 0.00
50 Providing and fixing 600x450mm bevelled edge mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board ground fixed cleats with CP brass screws and washers, etc., all complete as directed by Engineer-in-Charge. 4.00 Each 0.00
51 Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms, etc., all complete as directed by Engineer-in-Charge. 4.00 Nos 0.00
52 Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes, etc., all complete as directed by Engineer-in-Charge.
a) 75mm diameter 6.00 R m 0.00
b) 110mm diameter 10.00 R m 0.00
53 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, etc., all complete as directed by Engineer-in-Charge.
i) 75mm diameter 5.00 Nos 0.00
ii) 110mm diameter 5.00 Nos 0.00
b) Single tee without door
c) Bend 87.5 degree
i) 75mm bend 3.00 Nos 0.00
ii) 110mm bend 3.00 Nos 0.00
i) 75mm shoe 3.00 Nos 0.00
ii) 110mm shoe 3.00 Nos 0.00
54 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work
a) 15 mm nominal dia Pipes 10.00 R m 0.00
b) 20 mm nominal dia Pipes 10.00 R m 0.00
c) 25 mm nominal dia Pipes 6.00 R m 0.00
55 Providing and laying of 2mm thick Poly vinyl flooring sheet by using sutable rubber adhesive floor of approoved colur and design .Sample to be got approved by HAL before application, etc., all complete as directed by Engineer-in-Charge. 250.00 Sq m 0.00
56 Supply and fixing of Roller Blinds with polypropylene, maintenance free self controlled runners, power coated alluminium top channel, with control unit on either sides, dust proof, scorch guarded imported synthetic fabric, ball chain for operating, with plastic and nylon link chain, power caoted bottom weights with latest tilting mechanism on overlap of 12mm for each fabric in matching colours, etc., all complete as directed by Engineer-in-Charge. 45.00 Sq m 0.00
57 Providing and fixing long flat back urinal of HAL approved make ,size ,colour comprising of Spreader, ,Push cock ,32mm waste coupling (fully threaded) ,clamps and other fittings etc cutting and making good the walls wherever required all complete as directed by EIC/OIC. Urinal and fitting makes: CERA/HINDWARE/PARRYWARE/JAGUAR/or any other HAL approved makes 3.00 Each 0.00
Sub-Total of Part 'A' - Civil Works (Excluding GST) 0.00
PART - 'B' - ELECTRICAL WORKS
1 Supply, fixing in the existing 8 way TPN MCB DB(make:Legrand model:Ekinox) & testing of the following MCB's with necessary internal wiring using single core 4 sq mm copper wire of HAL approved make, complete in all respects, as directed by Engineer-in-charge.
a) 63A 415V, ratings, TPN MCB, "C" curve, 10 KA breaking capacity. 1.00 No 0.00
b) 40A 415V, ratings, TPN MCB, "C" curve, 10 KA breaking capacity. 1.00 No 0.00
c) 32A 415V, ratings, TPN MCB, "C" curve, 10 KA breaking capacity. 1.00 No 0.00
d) 32A 240V, SPN MCB, "C" curve, 10 KA breaking capacity. 6.00 Nos 0.00
e) 20A 240V, SP MCB, "C" curve, 10 KA breaking capacity. 4.00 Nos 0.00
f) 16A 240V, SP MCB, "C" curve, 10 KA breaking capacity. 4.00 Nos 0.00
2 Wiring for circuit / submain wiring along with earth wire with 2 X 4 sq. mm + 1 X 4 sq. mm sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 1500.00 R m 0.00
3 Wiring for light point / fan point / exhaust fan point/call bell point from nearest switch box with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, fan regulator, modular plate, suitable GI box and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required. (as per detailed CPWD specifications for Group C wiring)
a) Wiring to two light point controlled by 1 No 6A, 250V gr. flush type modular SP switch complete in all respects. 31.00 Points 0.00
b) Wiring to fan point controlled by 1 No. 6A, 250V gr. flush type modular SP switch including providing 1No box type GI/MS Fan hook in ceiling whereever required etc., complete in all respects. 26.00 Points 0.00
4 Wiring for circuit / submain wiring along with earth wire with 2 X 1.5 sq. mm + 1 X 1.5 sq. mm sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 30.00 R m 0.00
5 Wiring for circuit / submain wiring along with earth wire with 2 X 2.5 sq. mm + 1 X 2.5 sq. mm sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 500.00 R m 0.00
6 Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.
a) 8 Module 10.00 Nos 0.00
b) 6 Module 20.00 Nos 0.00
7 Supplying of following modular switch/ sockets on the existing modular plate & switch box including connections but excluding modular plate etc. as required.
a) 5/6 amps, one way modular switch, ISI marked 104.00 Nos 0.00
b) 3 pin 5/6 amps 2 way modular socket outlet, ISI marked 30.00 Nos 0.00
c) Stepped type Modular Fan regulator (2 module) 36.00 Nos 0.00
8 Fixing and testing of above Sl no 7(a,b,c) items in the existing modular plate & switch box including connections but excluding modular plate etc. as required. 10.00 Days 0.00
9 Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required. 50.00 Nos 0.00
10 Disconnecting/dismantling & removal of existing power distribution boards along with its wiring as-is-basis without any damage and handing over the same to the place as shown by Engineer-in-charge/Plant Maintenance department of Overhaul Division ( not more than 1KM ) including loading, transportation, unloading etc., complete in all respects and as directed by the engineer-in-charge.(Qty-30 nos) 5.00 Days 0.00
11 Supply, installation, testing & commissioning of 300mm dia 900 rpm heavy duty exhaust fan of any approved make with louvers, connecting cord with 6A, 3 pin plug top and with all necessary accessories, including making wall openings and replastering to smooth finish with matching paint etc., complete in all respects and as directed by Engineer-in-charge. 2.00 Nos 0.00
Sub-Total of Part 'B' - Electrical Works (Excluding GST) 0.00
Total of Part 'A' + 'B' - [Civil + Electrical Works] (Excluding GST) 0.00
Add 18% GST 0.00
Grand Total (Including GST) 0.00
HINDUSTAN AERONAUTICS LIMITED
Facilities Management Division
Pre-Qulification Profile (To Be uploaded along with Part A)
Tender Ref No. or Contract No.: HAL/FMD/R-107A/23-24
Name of Work: Renovation of HR Dept. in Overhaul Division, HAL [BC].
Estimated Amount in Rs.: 2670000
Tender Notice Date : 05.07.2024
PROVISIONAL GST ID NO. for HAL 29AAACH3641R1Z3
Sl.No Description Details Enclosed / Not Enclosed Remarks
1 Name of the Individual / Firm / Company: * Mandatory Please Enter Name of the Individual/firm/company
2 Type of ownership PlsEnter Type of Ownership
If Other, please specify
3 Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc., Pls enter Details of Constitution
4 Address for correspondence: Pls Enter Address
5 (a) PAN No.: Pls Enter Pan NO
5 (b) Service Tax Registration No
5 (c ) Goods and Service Tax ID No.
6 Contact details
Contact person name Please Enter Contact person Name
Mobile No. Pls Enter Mobile No
Ph. No. with STD code
FAX No. with STD code 3 #N/A
7 Registered Contractor
If Registered Contractor with HAL Yes/ No Related Document to be Uploaded to eProcurement Portal * Category: E= 75 Lakhs - Lessthan= 100Lakhs F= 50Lakhs - Lessthan 75 Lakhs G = 25Lakhs - Lessthan 50 Lakhs H = 10Lakhs - Lessthan 25 Lakhs I = 5Lakhs - Lessthan 10 Lakhs J = 2Lakhs - Lessthan 5 Lakhs K = Lessthan 2Lakhs 0 7 E 1
Registration No. 199999 7 F 2
Category 200000 6 G 3
PEMD Amount ( If paid ) 499999 6 H 4
8 I.T Returns for past 03 years 999999 5 J 6
2023-24 Pls Select 'Yes' ' No' for IT Return for All Three years 1000000 4 K 7
9 Average annual financial turn over during the last 3 years, ending 31st March 2023 of the previous financial year [ should not be less than 30% of Amount put to tender] 4999999 3
YEAR TURN OVER IN Rs. Enclosed / Not Enclosed REMARKS 5000000 2
2022- 2023 Rs. Pls Enter Turn over in Rupees for all the 3 years 7499999 2
Average annual Financial turn over 0.00 801000.00
Avg Annual Turnover criteria is not met 10000000 1
10 ESI & PF Nos with proof Nos Enclosed / Not Enclosed
ESI Registration No/. with proof if any Remarks if any
PF Registration No. with proof if any
11 Bank(s) details: [Copy of the cheque leaf to be uploaded]
Bank Account No. Related Document to be Uploaded to eProcurement Portal (Note Canceled cheque leaf to be uploaded)
Name of the Bank
Type of Account
12 Latest Bankers Solvency Certificate from Nationalized/ scheduled Bank issued NOT before 12 months from the last date of Tender submission solvency cal
Name of Bank & Branch Pls Enter Details to 'Name of the Bank' , 'Date of Issue','Value in Rs #REF! 28-Jun 0 40000
Date of Issue 200000 40000
Value in Rs. 200001 150000
Solvency value is NOT as per NIT
13 Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded] (i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost. (ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost. (iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender. 1068000 500001 250000
Completed similar works during last 7 years Pls Select %of similar works completed during last 7 years 1000000 250000
Work NoI Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 1000001 500000
Brief Description of Work: Please enter Details for Work No 1 2000000 500000
Completed value of Work in Rs. 2000001 1000000
Date of Commencement of Work 4000000 1000000
Date of Actual Completion of Work: 4000001 2000000
Work No II Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal 10000000 2000000
Brief Description of Work: Pls Enter Details for Work No II
Completed value of Work in Rs.
Date of Commencement of Work:
Date of Actual Completion of Work: work done
Work No III Type of Work: [ Incase of private works the same shall be supported with TDS certificate] Related Document to be Uploaded to eProcurement Portal #REF! 2555
Brief Description of Work: Pls Enter Details for Work No III #REF!
Completed value of Work in Rs.
Date of Commencement of Work:
Date of Actual Completion of Work:
14 Details of person holding the power of Attorney (If different from contact person)
Name Related Document to be Uploaded to eProcurement Portal
Mobile No. Pls Enter Details for Person holding Power of Attorney
Ph. No. with STD code
FAX No. with STD code
15 DECLARATION I
The document being viewed / downloaded from the website and having read & understood all the contents of the tender document mentioned under terms and conditions including price bid do hereby accept all the terms and conditions laid down in the said Tender document and will abide by the same on acceptance and ward of work.
16 DECLARATION II
I/We declare and confirm that - 1. All information and attachments submitted along with this offer are true and correct. 2. I/We are aware that any false information provided herein will result in the rejection of my offer. 3. I/We shall not make refund claims of expenditure incurred in processing this offer. 4. I / We aware that document sought only be uploaded for evaluation of offer. Pls Accept the Delaration II
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
raw.json
RAW_JSON
TN15.pdf
TENDER_DOCUMENT • 2.91 MB
107AChecklist.pdf
TENDER_DOCUMENT • 0.17 MB
107ATB.pdf
TENDER_DOCUMENT • 2.60 MB
107APBF.xlsm
TENDER_DOCUMENT • 0.06 MB
107AECSForm.pdf
TENDER_DOCUMENT • 0.46 MB
107APQ.pdf
TENDER_DOCUMENT • 0.21 MB
107APB.pdf
TENDER_DOCUMENT • 0.38 MB
107AUndertaking.pdf
TENDER_DOCUMENT • 0.55 MB
107APQF.xlsm
TENDER_DOCUMENT • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .