SPECIAL REPAIRS TO TOILET BLOCK OF JCO SINGLE LIVING ACCOMODATION AT CME UNDER GE CME KIRKEE.

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exc 15 cm thickness (below or above ground level) and removal of debris out of MD land complete all as specified and as directed.

M&L for 75 mm thick PCC (1:4:8) type D2 (using 40 mm graded stone aggregate) as in sub base including use and waste of necessary formwork complete all as specified and as directed.

M & L for 25 mm thick PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in sub base including use of necessary formwork complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing coat) removing serviceable tiles to store and removal of rubbish out side MD land complete all as specified and as directed.

M & L for coloured joint free non-skid ceramic tiles of 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including laid over and including 15 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed.

M & L for glazed coloured ceramic tiles of size 350x250x7mm /450x350x7mm thick of colour and pattern as approved by GE in vertical surfaces etc fixed and jointed in neat cement slurry and pointed in coloured cement to match complete, over and including 10mm thick backing coat in cement mortar (1:4) including triangular filleting on top in cement mortar (1:4) complete all as specified and as directed.

Demolition of brick work or stone masonry or block masonry built in cement or cement lime mortar. complete all as specified and directed.

M & L for block masonry with solid block of precast cement concrete class designation C-5 (using 20mm graded stone aggregate), exc 10cm in width and setting in cement mortar (1:6) complete all as specified and as directed.

M & L for block masonry with using old solid block exc 10cm in width and setting in cement mortar (1:6) complete all as specified and as directed. (Note:-Old solid block as retrieved from respective item herein before in good condition shall be used)

Taking down cement plaster of any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc and removal of debris out side MD land complete all as specified and as directed.

M&L 10 mm thick rendering in cement mortar (1:6) on stone masonry surfaces finished even and smooth (without using extra cement) over and including dubbing coat 10mm thick in cement mortar (1:6) complete all as specified and as directed.

M & L rendering 15mm thick other than fair face of masonry/concrete surface in cement mortar (1:4) mixed with WPC as per manufactures instruction over and including 10 mm thick dubbing coat in cement mortar (1:4) complete all as specified and directed. Note: WPC shall be measured and paid separately.

M & L for rendering 5mm thick on concrete surface in cement mortar (1:3) as in ceiling etc. finished even and smooth (without using extra cement) complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coats oil bound distemper over and including a coat of primer over thin layer of wall care putty (in two layers) complete all as specified and directed.

M & L preperation of newly plastered or previously untreated surfaces of wall and applying two coats of acrylic emulsion Exterior grade weather proof acrylic emulsion Antifungal and anti algea paint over one coat of primer complete all as specified and directed.

M & L for preparation of new plastered surface and applying two coats oil bound distemper over and including a coat of primer on ceiling over thin layer of wall care putty (in two layers) complete all as specified and directed

M & L for preparation of new plastered surface and applying three coats of white wash on ceiling complete all as specified and directed.

M & L for complete removal of existing treatment and applying two coats of oil bound distemper over and including thin layer of wall care putty (in two layers) including one coat of chalk whiting on walls complete all as specified and directed.

M & L for complete removal of existing treatment and applying two coats of oil bound distemper over and including thin layer of wall care putty (in two layers) including one coat of chalk whiting on ceiling complete all as specified and directed.

M & L for preparation of new plastered surface and applying three coats of white wash on walls complete all as specified and directed.

M & L for complete removal of existing treatment and applying two coats of white wash on ceiling complete all as sepcified and directed.

Taking up or down carefully steel water tubing, 15mm bore of pipe and connections including cleaning for refixing or removal to store complete all as specified & directed

Taking up or down carefully steel water tubing, 20mm bore of pipe and connections including cleaning for refixing or removal to store complete all as specified & directed

S & F and testing GI tubing of size 15mm bore 'medium grade' with and including all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in floors /walls//ceiling and including clips, wall hooks etc,complete and making necessary connection and testing on completion complete all as specified and directed

S & F and testing GI tubing of size 20mm bore 'medium grade' with and including all fittings such as bends, socket, tees, elbows, unions, barrel, nipple, plugs, etc laid in floors /walls//ceiling and including clips, wall hooks etc,complete and making necessary connection and testing on completion complete all as specified and directed

Refixing of old steel tubing of size 15mm bore of pipe and including with new connections in (wall/floor/ ceilings etc) complete all as specified & directed. (Note:-Old pipes as retrived from respective item herein before in good condition shall be used)

Refixing of old steel tubing of size 20mm bore of pipe and including with new connections in (wall/floor/ ceilings etc) complete all as specified & directed. (Note:-Old pipes as retrived from respective item herein before in good condition shall be used)

Dismantling CI/AC/PVC (SWR) pipes and fittings of any description fixed to wall/laid in trenches including makin g good disturbed portion of wall, floor, etc complete all as specified & directed.

Supply and fix PVC (SWR) pipe 110mm bore, single socketed in any length with rubber ring joints/ adhesive fixed to walls with FI clamps complete all as specified and as directed.

S & F 110 mm bore PVC (SWR) bend any radius, with oval access door fixed with rubber ring joints to pipe complete all as specified and as directed.

S & F PVC (SWR) branch pieces, single (single 'Y') equal or unequal, 110 mm bore provided with oval access door fixed with rubber ring joints complete all as specified and directed by Engineer-in Charge.

S & F PVC (SWR) branch pieces, double (double 'Y') equal or unequal, 110 mm bore provided with oval access door fixed with rubber ring joints complete all as specified and directed by Engineer-in Charge.

S & F PVC (SWR) junction, single (single 'T') equal or unequal, 110 mm bore provided with oval access door fixed with rubber ring joints complete all as specified and directed by Engineer-in Charge.

S & F PVC (SWR) junction, double (double 'T') equal or unequal, 110 mm bore provided with oval access door fixed with rubber ring joints complete all as specified and directed by Engineer-in Charge.

Supply and fix PVC (SWR) pipe 75mm bore, single socketed in any length with rubber ring joints/ adhesive fixed to walls with FI clamps complete all as specified and as directed.

S & F 75mm bore PVC (SWR) bend any radius, with oval access door fixed with rubber ring joints to pipe complete all as specified and as directed.

S & F PVC (SWR) branch pieces, single (single 'Y') equal or unequal, 75 mm bore provided with oval access door fixed with rubber ring joints complete all as specified and directed by Engineer-in Charge.

S & F PVC (SWR) branch pieces, double (double 'Y') equal or unequal, 75 mm bore provided with oval access door fixed with rubber ring joints complete all as specified and directed by Engineer-in Charge.

S & F PVC (SWR) junction, single (single 'T') equal or unequal, 75 mm bore provided with oval access door fixed with rubber ring joints complete all as specified and directed by Engineer-in Charge.

S & F PVC (SWR) junction, double (double 'T') equal or unequal, 75 mm bore provided with oval access door fixed with rubber ring joints complete all as specified and directed by Engineer-in Charge.

S & F in repair wall mount installation type, brass CP hand shower (Health Faucet) 15 mm bore with 1 metre long easy flex tube in chrome finish & wall hook complete fixed to wall all as specified and directed by Engineer-in Charge. (Make - Jaquar Cat No. ALD-565 or equivalent approved make indicated in list of makes in tender as approved by GE.

S & F in repair overhead shower 100 mm dia round shape single flow (ABS Body Chrome plated with grey face plate ) with Rubit cleaning system complete fixed to ceiling all as specified and directed by Engineer-in Charge. Make - Jaquar Cat No. OHS-1989 or equivalent approved make indicated in list of makes in tender as approved by GE.

S & F in repair stainless steel soap dish holder complete fixed to wall complete as specified and directed by Engr-in-Charge. Make- Jaquar Cat No ACN-1131N or equivalent approved make indicated in list of makes in tender as approved by GE.

S & F in repair brass CP chrome finish Toilet paper roll holder with flap fixed to wall with chromium plated brass screws complete all as specified and directed by Engr-in-Charge. Make:Jquar Cat No. AQN-7753 or equivalent approved make indicated in list of makes in tender.

S & F in repair brass chromium plated single towel rail, 60 cm long between flanges complete all as specified and directed by Engineer-in-charge. Make : Jaquar CAT No CAN-1111 NM or equivalent approved make indicated in list of makes in tender.

S & F in repairs brass chromium Angular stop cock with wall flange of 15mm bore capstan head complete all as specified and directed by Engineer-in-charge. Make - Jquar Cat No. CON- 059KN or equivalent approved make indicated in list of makes in tender.

S & F in repair brass CP pillar tap long neck with 450mm long braided hose chrome finish complete all as specified and directed by Engineer-in-charge. Make - Jaquar Cat No CQT-230218 or equivalent approved make indicated in list of makes in tender as approved by GE.

S & F in repair wall mixer brass CP with provision for overhead shower with 115 mm long bend pipe on upper side , connecting legs & wall flange chrome finish complete all as specified and directed by Engineer-in-charge. Make - Jaquar Cat No FUS-29273UPR or equivalent approved make indicated in list of makes in tender as approved by GE..

S & F in repair urinal of size 355 x 340 x 535 mm, white colour with grating and union for discharge pipe (excluding flushing Cistern, flush pipe and waste pipe), including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal backing cement including making connections complete all as specified and directed. Make - Jaquar Cat No. URS-WHT-13261 or equivalent approved make indicated in list of makes in tender as approved by GE..

Taking down floor trap/nahani trap of any description any size and making good disturbed portion with cement concrete (1:2:4) type B-1 with water proofing compound complete all as specified and directed.

M & L for 100 mm dia of outlet, cast iron floor trap, with stainless steel grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 & tested complete, all as specified and directed.

M & L 75 mm dia of outlet, cast iron nahani trap, with stainless steel grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 & tested complete, all as specified and directed.

S & F in repair 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and directed.

S & F in repair under counter wash hand basin vitreous china coloured including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling, chain and plug waste fitting union and 32mm dia PVC waste pipe 90cm long etc. complete all as specified, and all necessary inlet outlet connections complete all as specified and directed. Make - Hindware Cat No. 10065 or equivalent approved make indicated in list of makes in tender.

M & L for 20 mm thick granite work fixed over and including 15 mm thick cement mortar (1:4) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

M & L for machine cut cudappah stone slab 20-25mm thick fixed over and including cement screed base 15mm thick in CM (1:4) , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

S & F in viterous china wash down water closet pan (pedestal pattern) white, including P or S trap, provision of flush pipe, (including fixing bolts, and flush pipe) plastic seat any colour, closed pattern with flat bottom and cover and aluminium hinging device for pedestal pan complete all as specified and directed.

S & F in repairs vitreous china wall hung EWC Ivory colour, size 565x350x350mm, including matching colour closed pattern flat bottom soft close cover with mild steel chromium plated hinging device, fixed on wall, including providing and fixing plugs, bedding against wall in cement mortar (1:2), securing EWC to plugs with and including 60mm long brass screws, pointing around EWC using coloured cement including making connections complete all as specified and directed. Make: Cera, Cat No S1043119 (P Trap) or equivalent approved make indicated in list of makes in tender as approved by GE.

S & F wall mounted, twin flush, concealed flushing cistern, white (without knob and frame) of size (550 x 95 x 500 mm) fixed to full frame mounted on wall, including bedding against wall in cement mortar (1:2), making connections complete all as specified and directed. Make : Cera Siamp (without knob and frame) Cat No B1110108 or equivalent approved indicated in list of makes in tender.

S & F globe knob shine finish, push type for flushing cisterns including making connections complete all as specified and directed. Make : Cera Cat No B1120119 or equivalent approved make indicated in list of makes in tender.

S & F full frame for wall hung concealed flushing cistern fixed to wall using rag bolts complete all as specified and directed. Make : Cera Siamp Cat No B1130105 or equivalent approved make indicated in list of makes in tender as approved by GE.

S & F wall mounted, grab bar 600mm long fixed to wall using bolts complete all as specified and directed. Make : Cera Cat No B2210106 or equivalent approved make indicated in list of makes in tender as approved by GE.

S & F PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S & F in repairs stainless steel grating with or without hole 75mm dia complete as specified and directed by Engr-in-Charge.

S & F in repairs stainless steel grating with or without hole 100mm dia complete as specified and directed by Engr-in-Charge.

S & F in repair 15mm bore fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

Supply and fix in repair 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) double layered 'ISI' marked, hoisted & fixed in position including 20mm bore ball brass valve with polythene float and flynut, with existing inlet, outlets & provision of washouts, vent pipe, nipples of suitable size complete all as specified & directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) exc 1.5 sqmbut n.exc 4 sqm each and removing from site complete all as sepcifed and directed.

S & F 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamferred,put together with glue pinned at joints complete all as specified and directed.

S & F 30mm thick flush shutter, solid core construction, with block board core and both sides covered with plywood face panels with lipping/frame to match complete all as specified and directed.

M & L for two coats of synthetic enamel paint over coat of pink primer on wooden surfaces over 10 cm width or girth including preparation of new surfaces complete all as specified and directed.

M & L for mild steel works as in bands straps, hold fasts etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminious paint and sanded, complete all as specified and directed.

M & L for cement concrete (1:2:4) type B1 using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed including use and waste of necessary form work complete all as all as specified and directed.

M & L for preparing surfaces of iron materials and treating with tar or coal tar paint small articles such as stop, covers, gully grating, holdfasts, end of posts area exc 0.1 Sqm each complete all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutters from the frames) n exc 1.5 sqm each and removing from site complete all as sepcifed and directed.

S & F solid PVC door frame (conforming to IS) of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube,fixing in opening complete all as specified & directed.

S & F factory made solid PVC moulded door shutter, 30 mm thick 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and as directed.

S & F Mild steel butt hinges medium weight ,cold rolled, 100mm, ISI marked,complete as specified and as directed.

S & F aluminium anodised, barrel tower bolts, ISI marked of extruded section and fixed, length of bolt 200 mm complete all as specified and as directed.

S & F aluminium anodised, barrel tower bolt, ISI marked of extruded section and fixed, length of bolt 150 mm complete all as specified and as directed.

S & F 150 mm long aluminium anodised handles, ISI marked of extruded section complete all as specified and directed.

S & F 125 mm long aluminium anodised handles, ISI marked of extruded section complete all as specified and directed.

S & F 300mm long aluninium alloy, anodised , ISI marked, sliding door bolt with hasp, staple,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S & F in repairs PVC flexible waste pipe 32mm dia, 450mm long with full thread brass coupling and washers complete all as specified and directed by Engineer-in Charge.

M & L for cutting hole in brick walls/stone walls exc one brick thick but n.exc two brick thick for any purpose and making good dismantled position in cement mortar (1:3) or cement concrete (1:2:4) type B-1 as required complete as specified and directed by Engr-in-Charge.

M & L for cutting chases, pinning in stone, concrete block or slab walls and making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting n, exc 10 cm girth complete all as specified and directed complete as specified and directed by Engr-in-Charge.

M & L for sunken floor treatment as per following details :- Note :-This item continued at Sl no 11.01 to 11.08

(a) Demolition of existing treatment of any description and thickness and removal of rubbish outside MD land.

(b) Clean the sunken portion of toilet / Bath / WC / Kitchen thoroughly to remove laitance, dirt dust, etc.

(c) Form angle fillet of size 40mm x 40mm along the junction of wall and floor using polymer modified mortar "Dr Fixit" Pidicrete URP" or other equivalent product of M/S STP Limited/ M/S Fosroc chemicals/ M/S Thermax limited as approved by GE.

(d) Sanitary pipes entering through walls and floor shall be sealed with "Dr Fixit Bathseal Tape" and the gaps shall be grouted with non shrink cementitous grout "Dr Fixit Bathseal Grout" or other equivalent product of M/S STP Limited/ M/S Fosroc chemicals/ M/S Thermax limited as approved by GE. Nahani Traps, etc to be fitted securely and the gaps around it shall be grouted in the same manner.

(e) Apply one coat of a Bitumen modified polymer coating "Dr Fixit Bathseal Plus" or other equivalent product of M/S STP Limited/ M/S Fosroc chemicals/ M/S Thermax limited as approved by GE. on all angle fillets by brush and cover it with 100mm open woven mesh when it is still wet. Apply second coat of the same coating on the angle fillets and allow it to dry completely.

(f) In the remaining area, in dry substrate condition, apply first coat of the same coating with brush and further apply second coat when first coat is dried. Extend the coating upto 150mm above the FFL. Above FFL, another cementitious waterproofing coating "Dr Fixit Pidifin 2K" or other equivalent product of M/S STP Limited/ M/S Fosroc chemicals/ M/S Thermax limited as approved by GE. shall be further applied right upto 2.10 m to water proof the shower area also, if it is a bathroom or bath cubicles of a sanitary annex and apply second coat after 6-8 hours and allow to dry completely complete all as per manufacturers instruction and direction.

(g) After 2 to 3 days, sunken portion shall be overlaid with a 50 mm thick PCC (1:2:4) type B1 (using 20 mm graded stone aggregate) mixed with water proofing compound as per manufacturer's instructions laid to be slope 1:60 towards outer face of wall. Supply and fix 40mm outer dia UPVC pipe at the lowest point with 300mm projection beyond the outer face of the wall. Then fill up the sunken portion with lean concrete (1:5:10) type E2 (using 40 mm graded stone aggregate) complete all as per manufacturers instruction and direction and directed by Engineer in charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation boards / slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling timber fillets in framed work , rails, posts, rafters, purlins, etc under 40 sqcm in section complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position in framed work complete all as specified and directed.

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x38mm x 0.7mm, cross tee of size 24mm x 28mm x 0.7 mm using porpose made members interlocking to each other and 40mm x 3mm flat GI mild steel strip suspender made to shape at 1200mm c/c fixed with 3mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction. Make of GI Grid work : Armstrong/Swastik/Techno Grid Make of 'E' board : Everest/Indian Gypsum/Armstrong or equivalent approved .

Excavation in trenches n. exc 1.5 m wide and n. exc 1.5 mtr depth n exc 10 sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches n. exc 1.5 m wide and n. exc 1.5 mtr depth n exc 10 sqm on plan and getting out in hard/dense soil complete all as specified and as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete as specified and directed by Engr-in-Charge.

Demolition of brick work or stone masonry or block masonry built in cement or cement lime mortar. complete all as specified and directed.

M & L for rendering 15 mm thick cement mortar (1:6) on stone masonry surface or other than fair face of brick work including finishing even and smooth without using extra cement complete as specified and directed by Engr-in-Charge.

S & F Reinforced cement concrete (Hume) pipe of bore dia 150 mm , class NP2, laid and jointed with collar in trenches on concrete bed and making joints and testing complete inlcuding demolition of old pipe complete as specified and directed by Engr-in-Charge.

S & F Reinforced cement concrete (Hume) pipe of bore dia 200 mm , class NP2, laid and jointed with collar in trenches on concrete bed and making joints and testing complete inlcuding demolition of old pipe complete as specified and directed by Engr-in-Charge.

S & F Reinforced cement concrete (Hume) pipe of bore dia 250 mm , class NP2, laid and jointed with collar in trenches on concrete bed and making joints and testing complete inlcuding demolition of old pipe complete as specified and directed by Engr-in-Charge.

S & F Reinforced cement concrete (Hume) pipe of bore dia 300 mm , class NP2, laid and jointed with collar in trenches on concrete bed and making joints and testing complete inlcuding demolition of old pipe complete as specified and directed by Engr-in-Charge.

M & L for concrete bed of PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) to drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested.etc complete all as specified & directed. (Haunching shall be terminated at the crown of the pipe )

M & L for concrete bed of PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) to drain pipes of 200 mm bore including packing under and haunching against the sides of pipes after they are laid and tested.etc complete all as specified & directed. (Haunching shall be terminated at the crown of the pipe )

M & L for concrete bed of PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) to drain pipes of 250 mm bore including packing under and haunching against the sides of pipes after they are laid and tested.etc complete all as specified & directed. (Haunching shall be terminated at the crown of the pipe )

M & L for concrete bed of PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) to drain pipes of 300 mm bore including packing under and haunching against the sides of pipes after they are laid and tested.etc complete all as specified & directed. (Haunching shall be terminated at the crown of the pipe )

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc. 25cm in soils complete all as specified and as directed.

Removing excavated material (soil) to a distance not exceeding 50mtr and depositing where directed at a level not exceeding 1.5mtr above the starting point complete all as specified and as directed.

Dismantling of RCC slab other than ground floors and similar suspended works complete all as specified.

M & L for precast RCC slab (1:2:4), Type B1 using 20mm graded stone aggregate as in landings, cover slab (for man holes etc.,) chullah hoods, chajjas, water troughs,shelves and similar articles with plain faces and including necessary forms and moulds set in CM (1:4) complete all as specified and directed

S & F TMT steel bars 10 mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping for columns, hooking end and binding with and including MS wire annealed not less than 0.9 mm dia but in stirrups complete all as specified and directed.

Scooping & taking out sludge, sullage and foreign materials from manhole of any description and depth including removing and refixing of accessories and appliances required for safe disposal of sludge, sullage and foreign materials either by carrying the same in covered van/trolley outside defence land and it should be disposed off at such place which is not determinated to public health complete all as directed.

Cleaning and rodding the blocked sewage line to any depth till the smooth flow of sewage line is restored including plugging of manholes temporarily as and when required and washing down complete sewage line with water including removing sludge and foreign materials from manholes in line and removing and refixing manhole covers and rodding complete all as directed by Engineer-in-Charge for following dia of pipes

S & F three track sliding window with two or more shutter with 4 mm thick plane glass, one shutter of stainless steel mosquito proofing with good quality bearing, handle, lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make including taking down existing old window with frame of any description complete all as specified and directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & vertical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & bottom 20844

S & F aluminium anodised louvered ventilator with 4 mm thick pin headed glass and 100 mm wide glass strips, white framed and fixed with aluminium anodised frames etc including taking down existing old ventilator with frame of any description complete all as sspecified and directed. (a) SP 20048 (b) Glazing clips 19352

Taking down aluminium point wiring (light, fan, socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants holder,regulators sockets, light fitting etc removing materials deposited to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc.as per engr-in-charge.

M & L for point wiring of any length using approved colour coding as per IS, with stranded copper conductor 1.5 sqmm (Nominal area), single core, PVC insulated and unsheathed stranded cable 1100 volts grade, IS - 694 marked in FRLSH and including heavy duty, including PVC casing caping with including all accessories etc.,heavy duty ISI marked, including PVC boxes sunken box, surface/flush type with PVC sheet for mounting fittings such as switches sockets fan regulators etc including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth and connecting to earth dolly complete and and all as specified for the following:-

(a) One light/fan/socket or power point controlled by one way switch 5 Amps

(b) One multi 5 pin 5 amps Socket outlet point controlled by one switch on same board.

(c) One multi 5 pin 5 amps Socket outlet point controlled by one switch on independent board.

M&L for point wiring of any length using approved colour coding as per IS, with stranded copper conductor 2.5 Sq.mm(Nominal area),single core,PVC insulated and unsheathed stranded cable 1100 volts grade,ISI - 694 FRLSH marked including PVC casing caping with including all accessories etc.,heavy duty ISI marked,including modular white cover plate with frame and including including PVC box/ms sunken box surface/flush type with PVC sheet for mounting fittings of suitable size as per site requirement for housing switch ,socket,regulators etc,including PVC insulated stranded copper conductor 2.5 Sq.mm (nominal area) single core cable as earth and connecting to earth dolly complete and including cutting chases in the wall for box including making good of disturbed surface and all as specified for 16 Amps socket outlet on independent board.complete all as specified and as directed.

S & F ceiling rose on PVC square blocks surface bakelite 3 terminal. complete all as specified and directed

S & F switch piano, flush type single pole, one way, 5 Amp 250 volts,complete all as specified and directed

S & F Socket outlet multipurpose having provision for 3 pin, 6 Amp and 2 pin, 6 Amp, piano flush type complete all as specified.

Supply and fix surface wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver for LED tube complete with retrofit LED energy saving recess/surface mounted luminaries, high efficiency diffuser for soft glare free light of capacity 20 watt suitable of operation on 230 volt 50 Hz AC supply complete all as specified and as directed by Engineer-in-charge. Make Cat Part No ENDURALINEARNEOBS20WLED865SPCWH of Havells or equivalent model in Wipro/HPL/Philips as approved by GE.

Supply and fix integral sleek polycarbonate LED channel with white acrylic cover LED tube light fitting 10 watt & frame 2 ft in length complete all as specified and as directed by Engineer-in-charge. Make : Bajaj cat part No BCLSB 10 NW or Equivalent in Havells / Philips.

Supply and fix integral sleek polycarbonate LED channel with white acrylic cover LED tube light 5 watt & frame 1 ft in length complete all as specified and as directed by Engineer-in-charge. Make: Bajaj cat part No BCLSB 05 NW or Equivalent in Havells / Philips.

Supply and fix lamp holder PVC insulated body with back plate suitable for batten complete for 230 volt 50 Hz AC supply complete all as specified and as directed by Engineer-in-charge.

Supply and fix bldg security light fittings 30 watts capacity, 240 volts, Pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening seperate driver compartment with IP 65 Proptection and necessary fixing arrengements i.e pipe mounting GI bracket bent in shape not exceeding 1.5 mtr in length made out of 40 mm dia GI pipe complete all as specified and directed by Engineer-in-charge. Make- Havells Cat No ENDURACITYLITEPLATPLUSSL30WLED757SASYBOPC or same type in all respect of crompton/ Philips/ Havells as approved by GE

Supply and fix exhaust fan, AC single phase 230/ 240 volts heavy duty of size 300 mm sweep, 1400 rpm, with louvers including all fixing arrangements such as grounting cutting of hole in wall, cutting of plywood 18 mm thick for fixing arrangement for exhaust fan all as specified and directed.

S & F flushing to walls MCB distribution board double door 240 volts 8 way with 200 Amps rated bus bar and making good disturbed surfaces of walls complete all as specified and as directed

S & F MCB SPN 32 amps, 10kA, C series, 230 V complete all as specified and as directed

S & F MCB SP 6 to 32 amps, 10kA, C series, 230 V complete all as specified and as directed

M & L for sub main wiring with two runs of 4 sqmm single core multi stranded FRLSH PVC insulated and unsheathed copper conductor (red for phase and black for neutral) & one run of 4 sqmm single core multi stranded FRLSH PVC insulated and unsheathed copper conductor wire green coloured for earthing of grade 1100 V, FRLSH cable in and including electrical grade PVC casing caping of desired colour not less than 1.2 mm thick and 25 mm wide with complete accessories duly connected with earth dolly complete all as specified and as directed incl taking down old unserviceable one. Note: Two runs of 4 sqmm single core multi stranded PVC copper conductor, one run of 4 sqmm single core multi stranded PVC copper conductor and one run of PVC casing caping shall be measured as one length for payment.

M & L for earthing complete with Gl earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 m deep below GL) with top edge of the plate not less than 1.5 m below the normal ground level connected with GI earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel including necessary excavation & earth work in any type of soil, removing surplus soil to a distance not exc 50 M, with and including PCC chamber in PCC (1:2:4), type B1, using (20 mm graded stone aggregate), mild steel frame made out of angle iron of size 40 mm x 40 mm x 6 mm thick duly painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer hinged with and including 6 mm thick Cl cover with handle , watering arrangement with funnel internally secured with wire mesh with 20 mm dia medium grade GI pipe for watering, 40 mm dia light grade, Gl pipe for lead protection with and including alternate layer of charcoal dust and common salt complete all as shown in electrical plate No 3 of SSR Part I connected to earthing test point all as specified and indicated including testing on completion including retrieving of old GI earth plate, CI cover, GI pipes, angle iron frame from existing earthing as directed.

M & L for DBOX x combo plastic with enclosure for surface mounting 20 Amps MCB complete all as specified and as directed. Make :Havells Cat part No DHDTCSNO251020 or equivalent in Crompton/philips as approved by GE.

vishalconstruction

AJINKYA VIKRAM GAIKWAD

M/s ESS KAY Construction

MANISH VEDPRAKASH ARORA