MAINTENANCE OF EXTERNAL ELECTRIC WORKS WITH REROUTING OF LT CABLES AT BASE HOSPITAL UNDER GE (E/M) BHDC-10

Amount

Excavation in trenches not exc 1.5 m wide and not exc 1.5 m in depth for foundation/ fixing pole/ laying cable and pipe line etc or for man hole etc not exc 10 Sqm on plan and getting out in soft / loose soil complete all as specified and as directed.

M&L for providing dry river sand as in sand cushioning to under ground electric cable including punning down of sand in layer complete all as specified and as directed. Note: For measurement & payment purpose, punned thickness of sand only shall be considered.

Supply and Laying in replacement burn brick, sub class 'B', old size, having minimum compressive strength 75 Kg/Sqm, laid flat at right angle on the cable, for cable covering complete all as specified and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers, not exceeding 25 cm thick using excavated soil complete all as specified and as directed.

Removing the surplus soil to a distance not exceeding 50 metre and depositing where directed at level not exc 1.5 metre above the starting point complete all as specified and directed.

S&F in repair GI strip of size 25 X 4mm, as in earth continuity conductor or main earthing strip, fixed to wall/ chases or buried in ground or drawn in conduit (pipe/fixed to poles) of any type or any other situation for loop earthing etc including taking down old strip complete all as specified and as directed.

M&L in replacement 80 mm bore, GI tubing, light grade, for protection of cable/ earth continuity conductor, fixed to poles / walls / roof or laid in floors, road crossing or ducts, fixed with clamps, bolts nuts and washer etc including taking down old pipe complete all as specified and as directed.

M&L Earthing complete with galvanised Iron earth plate electrode 600x600x6mm thick, burried directly in ground (earth pit not less than 2.25mtr deep below GL) with top edge of the plate not less than 1.5 metre below normal ground level, surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all round the plate with using 32X6 mm GI earth strip electrode welded and revetted to earth plate up to a distance of 7.5 metre long, GI earth strip encased in and including 40mm bore GI light grade pipe, with 20mm bore GI pipe light grade as water pipe from earth chamber to upper edge of earth plate, MS funnel with wire mesh fixed on water pipe including excavation earth work, Provn of PCC pit in PCC 1:2:4 type B-1 chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1 duly reinforced with MS bars 8mm dia @ 150 mm centre to centre, both ways complete with lifting handle all as shown in electrical plate No 3 of SSR of part-I complete all as specified and as directed.

Supply, laying, connecting and testing in repair 400 Sqmm, 3.5 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe/ duct or fixed on pole including taking down old cable complete all as specified & as directed.

Supply, laying, connecting and testing in repair 185 Sqmm, 3.5 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe/ duct or fixed on pole including taking down old cable complete all as specified & as directed.

Supply, laying, connecting and testing in repair 120 Sqmm, 3.5 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe / duct or fixed on pole including taking down old cable complete all as specified & as directed.

Supply, laying, connecting and testing in repair 95 Sqmm, 3.5 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe / duct or fixed on pole including taking down old cable complete all as specified & as directed.

Supply, laying, connecting and testing in repair 70 Sqmm, 3.5 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe / duct or fixed on pole including taking down old cable complete all as specified & as directed.

Supply, laying, connecting and testing in repair 50 Sqmm, 3.5 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe / duct or fixed on pole including taking down old cable complete all as specified & as directed.

Supply, laying, connecting and testing in repair 25 Sqmm, 4 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe / duct or fixed on pole including taking down old cable complete all as specified & as directed.

Supply, laying, connecting and testing in repair 16 Sqmm, 4 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe / duct or fixed on pole including taking down old cable complete all as specified & as directed.

Supply, laying, connecting and testing in repair 10 Sqmm, 2 core, XLPE insulated, PVC inner sheathed, armoured with galvanised steel strip or wire, heavy duty, LT underground cable, with aluminium multistranded conductor, 1100 Volt grade, laid in trenches / duct, passing through pipe / duct or fixed on pole including taking down old cable complete all as specified & as directed. Note for item Nos 9.00 to 17.00:- Necessary Excavation, Earthwork, sand cushion, cable cover etc shall be measured and paid separately under respective items of this Schedule.

S&F in repair cable jointing kit for 11 KV (HT), earth grade cable, outdoor termination, Heat shrinkable type joint complete, with jointing material and accessories, suitable for XLPE armoured aluminium conductor cable of size 95 Sqmm, 3 Core complete all as specified and as directed.

S&F in repair cable jointing kit for 11 KV (HT), earth grade cable, Indoor termination, Heat shrinkable type joint complete, with jointing material and accessories, suitable for XLPE armoured aluminium conductor cable of size 95 Sqmm 3 Core complete all as specified and as directed.

S&F in repair cable jointing kit for 11 KV (HT), earth grade cable, straight through, Heat shrinkable type joint complete, with jointing material and accessories, suitable for XLPE armoured aluminium conductor cable of size 95 Sqmm 3 Core complete all as specified and as directed.

S&F in repair cable jointing kit straight through, outdoor type, Heat shrinkable type joint complete, with jointing material and accessories, suitable for 1.1 KV (LT), XLPE insulated cable of size 70 Sqmm 3.5 Core to 120 Sqmm x 3.5 core complete all as specified and as directed.

S&F in repair cable jointing kit straight through, outdoor type, Heat shrinkable type joint complete, with jointing material and accessories, suitable for 1.1 KV (LT), XLPE insulated cable of size 25 Sqmm 3.5 core to 50 Sqmm x 3.5 core complete all as specified and as directed.

S&F in repair cable jointing kit straight through, outdoor type, Heat shrinkable type joint complete, with jointing material and accessories, suitable for 1.1 KV (LT), XLPE insulated cable of size 185 Sqmm x 3.5 core complete all as specified and as directed.

S&F in repair cable jointing kit straight through, outdoor type, Heat shrinkable type joint complete, with jointing material and accessories, suitable for 1.1 KV (LT), XLPE insulated cable of size 240 Sqmm x 3.5 core complete all as specified and as directed.

S&F in repair On load change over switch, 630 Amp, capacity, 4 pole, with MS Enclosure, made of 3.15 mm thick steel sheet and extensible handle mounting stand, made from 35 x 35 x 5 mm thick channel, floor mounted and fixing in ground and necessary mounting accessories complete all as specified and as directed.

S&F in repair On load change over switch, 400 Amp, capacity, 4 pole, with MS Enclosure, made of 3.15 mm thick steel sheet and extensible handle mounting stand, made from 35 x 35 x 5 mm thick channel, floor mounted and fixing in ground and necessary mounting accessories complete all as specified and as directed.

S&F in repair On load change over switch, 250 Amp, capacity, 4 pole, with MS Enclosure, made of 3.15 mm thick steel sheet and extensible handle mounting stand, made from 35 x 35 x 5 mm thick channel, floor mounted and fixing in ground and necessary mounting accessories complete all as specified and as directed.

Supply, installation, testing and commissioning factory made and tested LT Panel, outdoor type, platform mounted, suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hzs, AC supply system, having bus bar chamber with insulated electrolytic Aluminium bus bars, TPN of capacity 1000 Amps rating, installed on DMC insulators with bus bar chamber. The panel shall be dust and vermin proof, and made out of 3.15 mm thick CRCA mild steel sheet and mild steel Mounting Channel 75mm X 50mm frame work, front openable type, Minimum panel Size (1875x2000x1000)mm, with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 Sqmm complete. All sheet metal works including frame shall be painted with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade, including necessary PCC, brick Masonry & plastering work for grouting of panel including disconnecting and removing the existing old unserviceable LT panel complete all as specified and as directed. The panel shall be suitable for accommodating and inclusive of following accessories (As described in Srl item Nos 28.01 & 28.02 here in after) complete all as specified and as directed:-

Outgoing ‐ (i) (a) MCCB 400A, 4P, 36kA - 02 Nos, Release: ATM (TM) Release (Adjustable O/L 80‐100% & Adjustable S/C 5‐10 In), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB -02 Nos : WiNbreak1: CSE3, (c) Spreader Terminals ‐4P (Set of 4) Suitable for 320A, 350A, 400A MCCB -04 Nos : WiNbreak1: CSE3, (ii) (a) MCCB 250A, 4P, 36kA, - 03 Nos, Release: ATM (TM) Release (Adjustable O/L d‐100% & Adjustable S/C 5‐10 In), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB-03 Nos : WiNbreak1: CSE2, (c) Spreader Terminals‐4P(Set of 4) Suitable for 160A, 200A, 250A MCCB -06 Nos : WiNbreak1: CSE2, (iii) (a) MCCB 160A, 4P, 25kA - 03 Nos, Release: ATM (TM) Release (Adjustable O/L 80‐100% & Adjustable S/C 5‐10 In), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB -03 Nos : WiNbreak1: CSE2, (c) Spreader Terminals‐4P(Set of 4) Suitable for 160A, 200A, 250A MCCB -06 Nos : WiNbreak1: CSE2, (iv) (a) MCCB 100A, 4P, 25kA - 02 Nos, Release: FMU (TM) Release (Adjustable O/L 80‐100% & Fixed S/C), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB -02 Nos : WiNbreak1: CSES, (c) Spreader Terminals‐4P(Set of 4) Suitable for 16A, 20A, 25A, 32A, 40A, 50A, 63A, 80A, 90A, 100A, 125A MCCB -04 Nos : WiNbreak1: CSES

Supply, installation, testing and commissioning factory made and tested LT Panel, outdoor type, platform mounted, suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hzs, AC supply system, having bus bar chamber with insulated electrolytic Aluminium bus bars, TPN of capacity 630 Amps rating, installed on DMC insulators with bus bar chamber. The panel shall be dust and vermin proof, and made out of 3.15 mm thick CRCA mild steel sheet and mild steel Mounting Channel 75mm X 50mm frame work, front openable type, Minimum panel Size (1275x1300x700)mm, with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 Sqmm complete. All sheet metal works including frame shall be painted with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade, including necessary PCC, brick Masonry & plastering work for grouting of panel complete all as specified and as directed. The panel shall be suitable for accommodating and inclusive of following accessories (As described in Srl item Nos 29.01 & 29.02 here in after) complete all as specified and as directed:-

Outgoing ‐ (i) (a) MCCB 250A, 4P, 36kA - 02 Nos, Release: ATM (TM) Release (Adjustable O/L 80‐100% & Adjustable S/C 5‐10 In), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB-02 Nos : WiNbreak1: CSE2, (c) Spreader Terminals‐4P(Set of 4) Suitable for 160A, 200A, 250A MCCB -04 Nos : WiNbreak1: CSE2, (ii) (a) MCCB 200A, 4P, 25kA - 02 Nos, Release: ATM (TM) Release (Adjustable O/L 80‐100% & Adjustable S/C 5‐10 In), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB-02 Nos : WiNbreak1: CSE2, (c) Spreader Terminals‐4P(Set of 4) Suitable for 160A, 200A, 250A MCCB -04 Nos : WiNbreak1: CSE2, (iii) (a) MCCB 100A, 4P, 25kA - 02Nos, Release: FMU (TM) Release (Adjustable O/L 80‐100% & Fixed S/C), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB -02Nos : WiNbreak1: CSES, (c) Spreader Terminals‐4P(Set of 4) Suitable for 16A, 20A, 25A, 32A, 40A, 50A, 63A, 80A, 90A, 100A, 125A MCCB : WiNbreak1: CSES, - 04 Nos

Supply, installation, testing and commissioning factory made and tested LT Panel, outdoor type, platform mounted, suitable for 415 Volts 3 Phase and neutral, 4 wire, 50Hzs, AC supply system, having bus bar chamber with insulated electrolytic Aluminium bus bars, TPN of capacity 400 Amps rating, installed on DMC insulators with bus bar chamber. The panel shall be dust and vermin proof, and made out of 3.15 mm thick CRCA mild steel sheet and mild steel Mounting Channel 75mm X 50mm frame work, front openable type, Minimum panel Size (1275x1300x700)mm, with proper ferrule & cable gland, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 Sqmm complete. All sheet metal works including frame shall be painted with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade, including necessary PCC, brick Masonry & plastering work for grouting of panel including disconnecting and removing the existing old unserviceable LT panel complete all as specified and as directed. The panel shall be suitable for accommodating and inclusive of following accessories (As described in Srl item Nos 30.01 & 30.02 here in after) complete all as specified and as directed:-

OUTGOING: - (i) (a) MCCB 250A, 4P, 36kA, -01 No, Release: ATM (TM) Release (Adjustable O/L 80‐100% & Adjustable S/C 5‐10 In), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB : WiNbreak1: CSE2, - 01 No (c) Spreader Terminals‐4P (Set of 4) Suitable for 160A, 200A, 250A MCCB : WiNbreak1: CSE2 -02 Nos (ii) (a) MCCB 200A, 4P, 25kA -02 Nos, Release: ATM (TM) Release (Adjustable O/L 80‐100% & Adjustable S/C 5‐10 In), Type: WiNbreak1 (b) Extended Rotary Handle Suitable for MCCB -02 Nos : WiNbreak1: CSE2, (c) Spreader Terminals‐4P(Set of 4) Suitable for 160A, 200A, 250A MCCB : WiNbreak1: CSE2 - 04 Nos (iii) (a) MCCB 100A, 4P, 25kA - 02 Nos, Release: FMU (TM) Release (Adjustable O/L 80‐100% & Fixed S/C), Type: WiNbreak1, (b) Extended Rotary Handle Suitable for MCCB : WiNbreak1: CSES, - 02 Nos (c) Spreader Terminals‐4P(Set of 4) Suitable for 16A, 20A, 25A, 32A, 40A, 50A, 63A, 80A, 90A, 100A, 125A MCCB : WiNbreak1: CSES - 04 Nos.

Supply, installation, testing and commissioning factory made and tested LT switch gear Panel (Minimum size 1800 x 1500 x 450 mm), outdoor type, platform mounted, totally enclosed, dust and vermin proof, made out of 50 x 50 x 6 mm thick MS angle iron frame, 0.50 Mtr height Legs and CRCA sheet of not less than 3.15 mm thick, as per IS 5039, cubical type, front and rear side openable, provision of air vent and provision of cable alley, with 630 Amps Aluminium rated bus bar for phases and 400 Amps rated bus bar for neutral, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 Sqmm complete. The panel shall be suitable for 415 Volts, 50 Hz, 3 Phase, 4 wire system and bus bars fixed on porcelain or PVC insulators, thimbles, glands of brass. All sheet metal works including frame shall be painted with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade, including necessary PCC, brick Masonry & plastering work for grouting of panel including disconnecting and removing the existing old unserviceable LT panel complete all as specified and as directed. The panel shall be suitable for accommodating and inclusive of following accessories (As described in Srl item Nos 31.01 here in after) complete all as specified and as directed:-

(a) INCOMMING: (i) MCCB Four Pole, 400Amp, 36KA, Microprocessor Based release for LSIG protection with ROH , AUX, Trip contact and Shunt release - 01 No (b) Metering and Indication: - (i) Digital Multifunction Meter with RS 485 Port, CI -1 (ii) CT for Meter CI -1.0,15VA (iii) RYB phase Indication light (iv) On /off/trip indication light-ACB (v) Control MCB SP (c) OUTGOING:- (i) MCCB TPN, 200A, 25 KA -01 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH (ii) MCCB TPN, 100A, 25 KA - 05 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH (iii) MCCB TPN, 63A, 25 KA - 02 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH

Supply, installation, testing and commissioning factory made and tested LT switch gear Panel (Minimum size 1800 x 1500 x 450 mm), outdoor type, platform mounted, totally enclosed, dust and vermin proof, made out of 50 x 50 x 6 mm thick MS angle iron frame, 0.50 Mtr height Legs and CRCA sheet of not less than 3.15 mm thick, as per IS 5039, cubical type, front and rear side openable, provision of air vent and provision of cable alley, with 1000 Amps Aluminium rated bus bar for phases and 400 Amps rated bus bar for neutral, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 Sqmm complete. The panel shall be suitable for 415 Volts, 50 Hz, 3 Phase, 4 wire system and bus bars fixed on porcelain or PVC insulators, thimbles, glands of brass. All sheet metal works including frame shall be painted with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade, including necessary PCC, brick Masonry & plastering work for grouting of panel including disconnecting and removing the existing old unserviceable LT panel complete all as specified and as directed. The panel shall be suitable for accommodating and inclusive of following accessories (As described in Srl item Nos 32.01 here in after) complete all as specified and as directed:-

(a) INCOMMING: (i) MCCB Four Pole, 630Amp, 36KA, Microprocessor Based release for LSIG protection with ROH , AUX, Trip contact and Shunt release - 01 No (b) Metering and Indication:- (i) Digital Multifunction Meter with RS 485 Port, CI -1 (ii) CT for Meter CI -1.0, 15VA (iii) RYB phase Indication light (iv) On /off/trip indication light-ACB (v) Control MCB SP (c) OUTGOING:- (i) MCCB TPN, 250A, 25 KA -01 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH (ii) MCCB TPN, 160A, 25 KA - 02 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH (iii) MCCB TPN, 125A, 25 KA - 04 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH (iv) MCCB TPN, 63A, 25 KA - 02 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH

Supply, installation, testing and commissioning factory made and tested LT switch gear Panel (Minimum size 1800 x 1500 x 450 mm), outdoor type, platform mounted, totally enclosed, dust and vermin proof, made out of 50 x 50 x 6 mm thick MS angle iron frame, 0.50 Mtr height Legs and CRCA sheet of not less than 3.15 mm thick, as per IS 5039, cubical type, front and rear side openable, provision of air vent and provision of cable alley, with 1000 Amps Aluminium rated bus bar for phases and 400 Amps rated bus bar for neutral, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 Sqmm complete. The panel shall be suitable for 415 Volts, 50 Hz, 3 Phase, 4 wire system and bus bars fixed on porcelain or PVC insulators, thimbles, glands of brass. All sheet metal works including frame shall be painted with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade, including necessary PCC, brick Masonry & plastering work for grouting of panel including disconnecting and removing the existing old unserviceable LT panel complete all as specified and as directed. The panel shall be suitable for accommodating and inclusive of following accessories (As described in Srl item Nos 33.01 here in after) complete all as specified and as directed :-

(a) INCOMMING: (i) MCCB Four Pole, 400Amp, 36KA, Microprocessor Based release for LSIG protection with ROH , AUX, Trip contact and Shunt release - 01 No (b) Metering and Indication:- (i) Digital Multifunction Meter with RS 485 Port, CI -1 (ii) CT for Meter CI -1.0, 15VA (iii) RYB phase Indication light (iv) On /off/trip indication light-ACB (v) Control MCB SP (c) OUTGOING:- (i) MCCB TPN, 200A, 25 KA -01 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH (ii) MCCB TPN, 100A, 25 KA - 05 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH (iii) MCCB TPN, 63A, 25 KA - 02 Nos, thermal Magnetic Based release for (O/L &S/C) protection with ROH

Supply, installation, testing and commissioning factory made and tested LT switch gear Panel (Minimum size 1800 x 1500 x 450 mm), outdoor type, platform mounted, totally enclosed, dust and vermin proof, made out of 50 x 50 x 6 mm thick MS angle iron frame, 0.50 Mtr height Legs and CRCA sheet of not less than 3.15 mm thick, as per IS 5039, cubical type, front and rear side openable, provision of air vent and provision of cable alley, with 600 Amps Aluminium rated bus bar for phases and 400 Amps rated bus bar for neutral, internal wiring with PVC insulated multistranded copper conductor FRLS cable of adequate size but not less than 1.5 Sqmm complete. The panel shall be suitable for 415 Volts, 50 Hz, 3 Phase, 4 wire system and bus bars fixed on porcelain or PVC insulators, thimbles, glands of brass. All sheet metal works including frame shall be painted with anticorrosive coating with seven tank process and finally epoxy polyester powder coating of Siemens grey RAL- 7035 shade, including necessary PCC, brick Masonry & plastering work for grouting of panel including disconnecting and removing the existing old unserviceable LT panel complete all as specified and as directed. The panel shall be suitable for accommodating and inclusive of following accessories (As described in Srl item Nos 33.01 here in after) complete all as specified and as directed :-

(a) INCOMMING: (i) MCCB Four Pole, 250Amp, 36KA, Microprocessor Based - 01 No (b) Metering and Indication:- (i) Digital Multifunction Meter with RS 485 Port, CI -1 (ii) CT for Meter CI -1.0, 15VA (iii) RYB phase Indication light (iv) On /off/trip indication light-ACB (v) Control MCB SP (c) OUTGOING:- (i) MCCB FP, 100A, 16 KA -04 Nos, thermal Magnetic (ii) MCCB FP, 63A, 16 KA -03 Nos, thermal Magnetic (iii) MCB FP, 63A, 10 KA -03 Nos (iv) MCB FP, 40A, 10 KA -03 Nos

S&F in replacement LED based sign board with LOGO and English Letter of size (3.75 Sqft) with stainless steel letters with acrylic top and back ACP channels, Words to be illuminated with LED modular and complete electric wiring with copper wire of size 1.5 Sqmm, All electric connection shall be tightened and fixed with proper lugs, All the words / LOGO shall be properly fixed on sign board including taking down old rusted sign board, including taking down all electrical wiring, and dismantling fitting fixture complete all as specified and as directed. Note:- Quoted rates shall be inclusive of the cost of Blue Colour 3mm ACP sheet, GI Channel and PCC work and LOGO etc complete.

S&F in replacement MS Cross arms, bracings, supports, clamp and back plates fabricated from structural steel section including nuts, bolts, washers, welding, bending cold or hot drilling holes for bolts in any type, shape or as indicated inclusive of one coat of aluminium paint over and including one coat of red oxide including taking down existing rusted/worn out MS cross arm, angle, clamps, nuts, bolts and washers complete all as specified and as directed.

S&F in replacement anti climbing device, spikes type, fabricated out of mild steel bars of size 16 Sqmm (round, square and flat) including MS Flat of size up to 32x6mm, nuts, bolts, washers and welding in two halves made to shape to suit the cross section of the pole complete with and including painting with two coats of aluminium paint over and including a coat of red oxide primer to match it with existing surfaces complete all as specified and as directed.

S& F in repair 11 KV HT hand Gloves rubber insulated complete all as specified and as directed.

S& F in repair Combination pliers insulated with thick C.A Sleeve complete all as specified and as directed. Make -Taparia Product Code 1621-6 or equivalent Model of Bosch/Jainson

S& F in repair long nose pliers insulated with thick C.A Sleeve complete all as specified and as directed. Make -Taparia Product Code 1430-6 or equivalent Model of Bosch/Jainson

S& F in repair wire stripping pliers insulated with thick C.A Sleeve complete all as specified and as directed. Make -Taparia Product Code WS-06 or equivalent Model of Bosch/Jainson

S& F in repair Universal Set (Adjustable Spanner, Insulated Pliers Screw Drivers) complete all as specified and as directed. Make -Taparia Product Code 1005 or equivalent Model of Bosch/Jainson

S& F in repair Home tool kit complete all as specified and as directed. Make -Taparia Product Code 1021 or equivalent Model of Bosch/Jainson

S& F in repair Allen Key set (10 Nos) complete all as specified and as directed. Make -Taparia Product Code AKI-10 or equivalent Model of Bosch/Jainson

S& F in repair line tester complete all as specified and as directed. Make -Taparia Product Code 813 or equivalent Model of Bosch/Jainson

S& F in repair screw driver set complete all as specified and as directed. Make -Taparia Product Code 840 or equivalent Model of Bosch/Jainson

S& F in repair Pipe wrinch, 350 mm length, suitable for up to 40 mm bore pipes complete all as specified and as directed. Make -Taparia Product Code 1274 or equivalent Model of Bosch/Jainson

S& F in repair 1500 Watt High Pressure Washer including Motor, Pump & Gun etc complete all as specified and as directed. Make - Bosch Model Aquatak 125 or equivalent Model of Stanley/Chasten/Karcher

S& F in repair 620 Watt Air blower complete all as specified and as directed. Make - Bosch Model No GBL 620-Watt or equivalent Model of Stanley/Chasten/Karcher

S& F in repair 5 Watt LED Torch with high intensity focused beam with twin switching mode complete all as specified and as directed. Make - Havells Ordering Code LHEXAOPFUN1G005 or equivalent Model of Make mentioned in PS.

S& F in repair 5 Watt LED lantern cum Torch with twin charging mode 5V charging cable or integrated solar Panel complete all as specified and as directed. Make - Havells Ordering Code LHEXTDP7HN1G005 or equivalent Model of Make mentioned in PS.

S& F in repair power Crimping tool capacity up to 400 Sqmm with all die complete all as specified and as directed. Make : Jainson, Model JUPITER-400 or equivalent model of Dowells/Bosch

S&F in Replacement Inverter LED batten with square profile and polycarbonate channel, Lithium Ion battery with charging time 8-10 hours and back up time up to 4 hours, 10 Watt, surface/ wall mounted, with aluminium housing & integrated electronic driver and all fixing accessories complete all as specified and as directed. Make: Havells ordering Code LHEXACP7FN1W010 or equivalent Model of make mentioned in PS.

S&F in replacement, Inverter LED Bulb, B22 cap, 9 watt, with Opal diffuser, IP20, 4 Hrs backup complete all as specified and as directed.

S&F in replacement Surface/Wall Mounted, 9 Watt, integrated LED batten light, 6000 K, 2 feet Fitting, energy efficient, with Epoxy powder coated white polycarbonate channel housing Complete with all accessories as required complete all as specified and as directed. Make - Havells Cat part No -LHEXBLP7IN1W009 or equivalent model of Make mentioned in PS.

S&F in replacement Surface/Wall Mounted, 18 Watt, integrated LED batten light, 6000 K, 4 feet Fitting, energy efficient, with Epoxy powder coated white polycarbonate channel housing Complete with all accessories as required complete all as specified and as directed. Make - Havells Cat part No -LHEXBLP7PN1W018 or equivalent model of Make mentioned in PS.

S&F in Replacement Aesthetically designed rechargeable LED Lantern, 3 Watt, with long backup time, with rechargeable Li-ion battery of capacity 3.7 V, 2000 mAh, surface/ wall mounted complete all as specified and as directed. Make: Havells ordering Code LHEXTEP7HN1R003 or equivalent Model of make mentioned in PS.

S&F in Replacement Aesthetically designed rechargeable, 3 CCT, changing and dimming, 4.5 Watt sleek and portable LED Table Lamp, with rechargeable battery of capacity 4 V, 2000 mAh complete all as specified and as directed. Make: Havells ordering Code LHEXBZPNFN1W4X5 or equivalent Model of make mentioned in PS.

S&F in replacement, LED Bulb, B22 Cap, 5 Watt complete all as specified and as directed.

S&F in replacement, LED Bulb, B22 Cap, 7 Watt complete all as specified and as directed.

S&F in replacement, LED Bulb, B22 Cap, 9 Watt complete all as specified and as directed.

S&F in replacement, LED Bulb, B22 Cap, 15 Watt complete all as specified and as directed.

Vishal Traders

Saini Enterprises

S S CONSTRUCTION

SANJEEV ENTERPRISES

RUCHIKA ENGG.WORKS

M/S Rohit Enterprises