COMPREHENSIVE MAINT AND CONNECTED B/R ALLIED WORKS AT DGIS UNDER AGE B/R-I OF GE (SOUTH) DELHI CANTT-10

Amount

Attending complaint for petty repair to leaking water in bib tap, pillar tap, stop cock, angle valve, flushing cistern, WHB, Sink, wall mixer etc. of any description any size by changing the washers(s)/jumper(s) etc, by adjusting/replacing the washer(s) and adjustment of lever required for making the flushing cistern functional, by tighting the leaking waste pipe of WHB/Sink and providing 'M' seal to stop leakage as required. Removal of air lock/blockage of water in GI water tubing and cleaning the pipe or fittings etc. including replacement of major defective item if required, complete all as specified and as directed.

Note:- 1. The contractor shall make all arrangement for attending the different types of complaints area on day to day basis. Any major item required to be replaced with new one, to make the system functional shall be measured and paid for separately as "M&L" under respective item of this schedule. Old retrieved item(s) as considered in 'Schedule of Credit' shall become property of the contractor. Contractor has to provide minimum one carpenter including all necessary T&P on all working days from 9AM to 5PM. Additional workers can be engaged if nature of work required to be completed within fix time frame as desired by the GE. Rate shall be quoted accordingly against these items, keeping in mind above said provisions. 2. Contractor shall provide minimum one plumber with helper including all necessary T & P on all working days from 9AM to 5 PM .Additional workers can be engaged if nature of work required to be completed with in fixed time as desired by GE . Rate shall be quoted accordingly . Keeping in mind above said provisions. 3. Where material provided shall be paid as "S&F underrespective item of Sch. 'A' the payment of complaint under this item shall not be paid.

Note:- 4. Based on complaint received from users. Concerned JEs shall deploy the tradesmen in same day through Job slip (complaint slip) and the contractor shall ensure that the complaint are to be attended and rectified in same day and complain slip shall be got signed by users with date. Non compliance (not attending) the complaint in same day a panel recover of Rs.100/Per complaint shall be made from contractors due (claims). 5. The contractor shall provide job slip serially machine numbered, attendance register and complaint registered, and the rate quoted by the tender shall deemed to be included for these provision. 6. These document may be asked to produce at the time of payment of RAR/Bill.

S&F in repairs brass jumper washer, brass head, face and spindle for bib cock/pillar cock/stop cock 15 mm bore any type complete all as specified and as directed.

S&F in repairs chromium plated bib tap, long body with flange, cast copper alloy (fancy type), screwed for 15mm bore iron pipecomplete all as specified and as directed.

S&F in repairs Chromium plated Pillar tap cast copper alloy with capstan heads fency type screwed down high pressure screwed to 15 mm bore iron pipe complete all as specified and as directed.

S&F in repairs chromium plated Stop valve/angle valves (fency type) cast copper alloy, complete all as specified and as directed.

S&F in repairs chromium plated brass overhead shower rose 75mm dia with arm 255mm with flange with swivel joints, any size, including fixing to steel pipe or union for 15mm bore pipe complete all as specified and as directed.

S&F in repairs, brass CP towel rail 60Cm long complete all as specified and as directed.

S&F in repairs PTMT bib tap standard, (Minimum weight 90 gms) any colour, fixed to 15 mm bore iron pipe complete all as specified and as directed.

S&F in repairs small fittings galvanised iron 'medium grade' such as socket, elbow, nipple of any length upto 150mm long, Tee, union etc for 15 mm bore pipe (ISI marked) complete all as specified and as directed.

S&F in repairs small fittings galvanised iron 'medium grade' such as socket, elbow, nipple of any length upto 150mm long, Tee, union etc for 20 mm bore pipe (ISI marked) complete all as specified and as directed.

S&F in repairs PVC connection 15 mm dia 45 cm long with 2 Nos check nuts with washer complete all as specified and as directed.

S&F in repairs sinks with drainage board made of stainless steel 1.00mm thick kitchen or laboratory with plugs , washers and wastes including bnedding in cement mortar to dwarf wall or including fixing cantileter brackets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and as directed.

S&F in repairs 32 to 40 mm dia PVC waste pipe for WHB & sink, 60 cm long with union complete all as specified and as directed.

S&F in repairs CP grating 127 mm dia with/without hole round, fixed on floor/nahani trap, fixed with cement mortar (1:3) complete all as specified and as directed.

S&F in repairs PVC syphone with handle complete for low level flushing cistern complete all as specified and as directed.

S&F in repairs PVC long bend for low level flushing cistern complete all as specified and as directed.

S&F in repairs 10 litres capacity PVC Low level flushing cistern including PVC syphon and float valve with float, PVC long bend for out let connection of cistern with WC complete fixing and connecting bend with WC complete all as specified and as directed.

S&F in repairs PVC Polyplast float valve for cistern tank complete all as specified and as directed.

S&F 15mm bore galvanised iron pipe medium grade with all fittings fixed to wall and ceiling or laid in floor including taking down of old GI pipes and connections complete all as specified and as directed.

S&F 20 mm bore galvanised iron pipe medium grade with all fittings fixed to wall and ceiling or laid in floor including taking down of old GI pipes and connections complete all as specified and as directed.

S&F in repairs white, vitreous china wash hand basin, flat back, size 550x400 mm, excluding taps, waste chain and plug and porcelain stopper but including brackets and 32 mm dia waste fittings brass chromium plated with long screwed shanks and fly nuts, 32MM X 600 MM long PVC waste pipe complete flange end bedded in red lead cement and other end fixed complete all as specified and as directed.

S&F in repairs vitreous china squatting pan, (Orissa pattern) size 580x440mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection to trap etc complete including making good to floor complete all as specified and as directed.

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including waste pipe including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement with Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified

S&F Vitreous china urinal partition white of size 310x700 mm complete all as specified and as directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

Disconnecting existing tanks of capacity exc 250 ltr n.cex 500 ltr , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed. (Cleaning repairing etc. measured separately).

Disconnecting existing tanks of capacity exc 500 ltr n.cex 1000 ltr , setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed. (Cleaning repairing etc. measured separately).

Cleaning and removing all scale and dirt, etc. from tanks of capacity exc 250 ltr & n. exc 500 ltr and form mouths of circulating pipes, etc.

Cleaning and removing all scale and dirt, etc. from tanks of capacity exc 500 ltr & n. exc 1000 ltr and form mouths of circulating pipes, etc.

S&F 500 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including taking down old PVC tank etc,complete all as specified and as directed.

S&F 1000 Ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including taking down old PVC tank etc, complete all as specified and as directed.

S&F 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms)

S&F in repairs HDPE PVC lid (cover) for 300 to 1000 Litres capacity PVC tanks, in repairs complete all as specified and as directed.

S&F 100 mm bore cast iron sand soil waste or vent pipes (ISI Marked), in any length with or without ears with joints in cement mortar (1:3), laid in trenches, floors or fixed to walls including making good to match with existing surfaces including taking down old pipes with all fittings and dismantling PCC/Brick work etc, complete all as specified and as directed.

All as above Srl item No. 34 above, but 75 mm bore complete.

S&F in repairs, 100 mm bore of cast iron branch pieces (ISI Marked), single (equal or unequal) ordinary of inverted spigot or socket typec omplete all as specified and as directed.

All as above Srl item No. 36 above, but 75 mm bore complete.

S&F in repairs 100 mm bore pipe, cast iron bends (any radius) diminishing pieces or tapers (larger bore measured)complete all as specified and as directed.

All as above Srl item No. 38 above, but 75 mm bore complete.

M&L in repairs 75 mm out let dia CI floor trap incl jointing to waste pipe in run lead complete all as specified and as directed.

M&L in repairs 100 mm out let dia CI floor trap incl jointing to waste pipe in run lead complete all as specified and as directed.

S&F PVC(SWR) pipes 110mm bore size single socketed, in any length with rubber ring joints, fixed to wall with and including MS flat iron clamp 25x 3 mm including taking down old rain water pipe etc, complete all as specified and as directed.

S&F in repairs PVC(SWR) bends any radius, of 110mm bore sizecomplete all as specified and as directed.

Attending complaint for petty repair to easing of Doors/Window/Cup Board shutters by tightening of hinges / handles / Al-drop bolt / tower bolt / knobs, hasp and stapple etc of any size / any number of panels for easy closing / opening or changing the position of hinges, adjustments of tower bolts,sliding bolts, replacement of looking mirror etc complete including replacement of major defective item if required complete all as specified and as directed.

Note:- 1. The contractor shall make all arrangement for attending the different types of complaints area on day to day basis. Any major item required to be replaced with new one, to make the system functional shall be measured and paid for separately as "M&L" under respective item of this schedule. Old retrieved item(s) as considered in 'Schedule of Credit' shall become property of the contractor. Contractor has to provide minimum one carpenter including all necessary T&P on all working days from 9AM to 5PM. Additional workers can be engaged if nature of work required to be completed within fix time frame as desired by the GE. Rate shall be quoted accordingly against these items, keeping in mind above said provisions. 2. Contractor shall provide minimum one carpenter with helper including all necessary T & P on all working days from 9AM to 5 PM .Additional workers can be engaged if nature of work required to be completed with in fixed time as desired by GE . Rate shall be quoted accordingly . Keeping in mind above said provisions.

Note (Contd..):- 3. Where material provided shall be paid as "S&F underrespective item of Sch. 'A' the payment of complaint under this item shall not be paid. 4. Based on complaint received from users. Concerned JEs shall deploy the tradesmen in same day through Job slip (complaint slip) and the contractor shall ensure that the complaint are to be attended and rectified in same day and complain slip shall be got signed by users with date. Non compliance (not attending) the complaint in same day a panel recover of Rs.100/Per complaint shall be made from contractors due (claims). 5. The contractor shall provide job slip serially machine numbered, attendance register and complaint registered, and the rate quoted by the tender shall deemed to be included for these provision. 6. These document may be asked to produce at the time of payment of RAR/Bill.

M&L welding in repairs n.exc 2.5 cm in length of any thickness of metal in any situation and in any position such as hinges and similar articles etc for steel door, gates, window, ventilatiors and grills etc for upto four stoery building complete all as specified and as directed.

S&F in repairs 200mm mild steel barrel tower blots, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F in repairs 100mm size of butt hinges, medium weight cold rolled mild steel complete for door etc, with welding to steel chowkhats, at any floor up to four storied bldgs and making it functional, in repairscomplete all as specified and as directed.

S&F in repairs steel window handles (right & left) and peg stays etc as per sample complete all as specified and as directed.

S&F in repair 125 mm aluminium anodised handle cast type,complete all as specified and as directed.

S&F in repair 150 mm aluminium anodised handle cast type complete all as specified and as directed.

S&F in repairs MS Morties lock mild steel 4 levers vertical type size 100mm fixed in floor complete all as specified and as directed.

S&F in repairs for double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

S&F in repairs aluminium (die cast body) Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg and fixed complete all as specified and as directed.

S&F in repairs 3 mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.50 Sqm in each pane incl taking down old broken glass complete all as specified and as directed.

M&L for easing of aluminium doors by adjusting floor / hydraulic door closer including jointing of cleats and hinges for smooth functioning including necessary taking down and refixing in the same opeing with entire satisfaction of Engr-in-Charge complete all as specified and as directed.

S&F in repairs rubber bead for fixing of aluminium doors glass complete all as specified and as directed.

S&F in repair powder coated aluminium frame for partitions,doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

S&F in repair aluminum powder coated door shutter, aluminium section weighing not less then 0.55 Kg/m incl necessary jointing cleats, glazing clips rubber neoprene packing incl (a) 150mm handle - 02 Nos (b) Stainless steel hinges - 100mm - 03 Nos (c) Mortice lock in built 3 lever-01 Nos in each shutter, alum anodized snap beading screw etc complete all as specified and as directed. Note: Glass & particle board shall be measured and paid separately under respective items.

S & F 4.8 mm thick tinted glass fixed to aluminum frame work with rubber beading gasket complete all as specified and as directed.

S&F 12mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work fixed to aluminum framing all as specified and as directed.

S&F 12mm toughened glass coloured match with existing glass including all necessary fittings up to 4th story bldg complete all as specified and as directed.

S&F Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1: 6 including dismantling old tiling including cement mortar bedding (but not backing) of any description and thickness and removal of rubbish off the premises complete all as specified and as directed.

S&F Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in cement mortar 1: 6 including dismantling old tiling including cement mortar bedding (but not backing) of any description and thickness and removal of rubbish off the premises complete all as specified and as directed.

S&F coloured glazed ceramic tiles of size 200mm x 300mm x 6 mm thick, on vertical surfaces such as dados etc, set and jointed in neat cement slurry and pointed in white cement over and incl 10 mm thick rendering in cement mortar 1:4 including dismantling old tiling including cement mortar bedding (but not backing) of any description and thickness and removal of rubbish off the premises complete all as specified and as directed.

S&F glazed vitrified tiles 9 to 10 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm ( size 600 mm x 600 mm), in floors/skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match

M& L for 20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of graniteand including 15 mm thick screed bed in cement mortar 1: 6 including dismantling old tiling including cement mortar bedding (but not backing) of any description and thickness and removal of rubbish off the premises complete all as specified and as directed.

M& L for glazed coloured ceramic tiles in vertical surface of size 450X300X7mm thick, set and jointed in neat cement slurry and pointed in white cement over and incl 10 mm thick rendering in cement mortar 1:4 including dismantling old tiling including cement mortar bedding (but not backing) of any description and thickness and removal of rubbish off the premises complete all as specified and as directed.

S&F machine cut kota stone slab flooring 20-25 mm thick laid over 20 mm thick cement screed base 1: 6 , laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing including dismantling old tiling including cement mortar bedding (but not backing) of any description and thickness and removal of rubbish off the premises complete all as specified and as directed.

M&L cleaning of / removal of forgeion material from roofs (complete roof for one block), like tree leafs, small busses, grass, trees shrubs, small plants girth not exceeding 30 cm, etc and clean grating jallies at mouth of rain water pipe ,and made functional all the rain water pipes, including removing of all debries from roof by collecting in gunny begs and thrown away at a distance not exceeding 1 km meter from site complete with entire satisfactin of Engr-in-Charge complet all as specified and as directed. Note :- a) A pucca bond register shall be maintained showing block number building number, date of cleaning. Signature of conractor, JE/Engr-in-Charge and users (Top floor occupent) shall be obtained for every Block/Building where cleaning of roof has been done. b) The register may be asked while claiming the payment by the contractor. c) The said item shall not be executed to the block/buildings which are under defect liability period/under demolition and special repair work is likely to be commenced.

M&L for cement concrete (unreinforced) 1:2:4, type B-1, using 20 mm graded stone aggreegate in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L for Cement concrete 1:3:6 type C2 using 40mm graded stone aggregate in plinth protection, 75mm thick, finished fair and even without using extra cement,complete all as specified and as directed.

M&L for 100mm thick PCC 1:2:4 type B2 (40mm graded aggregates) as in finishing cement concrete surface even and smooth with out using extra cement complete all as specified and as directed.

Demolition of brick work built in CM incl quoins, arches, pillers etc. complete all as specified and as directed.

M&L brick work in cement mortar (1:6) using sub class 'B' bricks, straight or curved on plan exc 6 mtr mean radius complete all as specified and as directed.

Taking down shutters of any description area exceeding 1 Sqm & not exceeding 2 Sqm each and refixing in the same opening complete all as specified and as directed.

Taking down shutters of any description area exceeding 1 Sqm & not exceeding 2 Sqm each complete all as specified and as directed.

Taking down door chowkhat or frame with shutters (without taking off shutters from the frame exc 1.5 sqm but nexc 4 sqm each complete all as specified and as directed.

S & F Pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per manufacturers instructions drawings complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails.MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side as gap insert for top rails bottom rail, panelling of plain colour PVC sheet to be fitting in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specification and drg complete all as specified and as directed.

S&F 35 mm thick, 2nd class hardwood, glazed and Skelton shutters, open rebated and prepared to receive glass / gauze etc ( with or without sash bars) edges of framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutters as specified in SSR Part-I section 8 clause 8.24(a) complete all as specified and as directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

M&L for preparation of newly wooden surfaces of any description over 10 cm in width or girth not other wise described and applying two coats of synthetic enamel paint over a coat of wood primer complete all as specified and as directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel complete all as specified and as directed.

S&F 100 mm butt hinges of stainless steel medium weight complete all as specified and as directed.

S&F 200 mm long SS barrel tower bolt of extruded section complete all as specified and as directed.

S&F 125 mm SS handle cast type,complete all as specified and as directed.

S&F 150mm long SS barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing ISI marked 250mm long SS sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring of 140 mm size with vulcanised rubber piece complete all as specified and as directed by Engineer-in-Charge

S&F in repairs stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to aluminium window frame / wooden doors or steel section windows complete all as specified and as directed by Engineer-in-Charge

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to aluminium window frame / wooden doors or steel section windows complete all as specified and as directed.

Distmantling of ceiling boards (fibre, pulp, insulation etc.) or insulation bords/ slab/blankets, any thicness, including cover fillets complete all as specified and as directed.

S&F anodised aluminium snap grid frame (with minimum 15 micron uniform anodic coating) size of 605mm x 605mm consisting of Tee/Angle section, size 40 x 40 x 2mm as approved make confirming to IS-733 in frame of false ceiling including aluminium cleat with necessary CP brass/stainless steel shunk screws. Aluminium perimeter angles fixed to wall/wooden frame at centre to centre and fixing frames to level adjusting anchors 8mm dia GI wire with hook in Tee members at 1.5m centre to centre fixed to steel trussed roof complete all as specified and as directed.

M&L 4mm thick non asbestos (E board) fibre cement building boards fixed or laid/inserted to aluminium frame work with screw in ceiling complete all as specified and as directed.

M&L for Dholpur stone 25-30mm thick cladding gangsaw cut machine cut edges, uniform colour of each stone size exc 0.25 sqm area and not exc0.50 sqm area (Stone size as per site) fixed with and including one number SS clamps (grade 202) of flat 30mm x 2mm ,150 mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for fastner, polishing, rubbing & including silicon treatment and grouting with CM 1:3 (SS Fastners 75-100mm long, Make HILTI, FISHER)complete all as specified and as directed. Note : Necessary scaffolding rates included in the above item.

M&L for drilling hole in the existing dholpur stone 20-25 mm thick (flush fastner fixed in the centre of each stone) for fastner, polishing, rubbing & including silicon treatment and grouting with CM 1:3 on existing stone on wall and match with existing colour (SS Fastners 75-100mm long) complete all as specified and as directed. Note:- The height of building up to 4th storey building, necessary scaffolding rates included in the items.

S&F in repair vitreous china wash down water closet pan EWC (pedestal pattern as rqd) p or s type (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repairs plastic water closet seat cover white closed pattern with flat bottom and cover and mild steel chromium plated or aluminium anodised hinging device complete all as specified and as directed.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and all as directed.

M&L for rendering 10mm thick in cement mortar 1: 6 on faces of brick work or concrete surfaces, finished fair and even complete all as specified and as directed.

M&L for rendering 10mm thick in cement mortar 1: 6 and top layer 5mm thick in cement mortar 1: 4 mixing water proofing compound on faces of brick work or concrete surfaces, finished fair and even complete all as specified and as directed.

Supply only liquid water proofing compound conforming to relevant IS complete all as specified and as directed.

M&L for Rendering 5mm thick in cement mortar 1: 3 on concrete surfaces of ceiling,chajja,etc finished fair and even complete all as specified and as directed.

M&L for applying two coats on new surfaces of external wall/ceiling with Graco-490 spray machine, of GreenPro certified water-based, modified acrylic, exterior Apex Suprema Emulsion or equivalent as per required shade (Company depot tinted) with silicon additives, heat reflectant property, VOC less than 2% by mass, Class A IS-15489 and IS-101 @5-6sqm/ltr over a coat of primer after cleaning and removing dirt dust oil grease smog efflorescence stain, thoroughly brushing the surface and removal of existing paint flakes, necessary tools and machinery to give an even shade. Application to be done only by applicator authorised by manufacturer and also shall be approved by GE before starting of work complete all as specified and as directed.

M&L for complete removal of existing loose treatment by scraping with mechanical wall/ceiling by vacuum based sanding machine (wall sanding machine with internal dust extraction system & having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 grit having dia of 7 ich/ 9 inches to make the surfaces free from dust, loose paint etc by using smart periodical methodology/auto roller complete all as specified and as directed.

M&L for applying two coats of Asian wall putty upto 2-3 mm to get even or smooth surface complete all as specified and as directed.

M&L for applying one coats on old surfaces of external wall/ceiling with Graco-490 spray machine, of GreenPro certified water-based, modified acrylic, exterior Apex Suprema Emulsion or equivalent as per required shade (Company depot tinted) with silicon additives, heat reflectant property, VOC less than 2% by mass, Class A IS-15489 and IS-101 @5-6sqm/ltr after cleaning and removing dirt dust oil grease smog efflorescence stain, thoroughly brushing the surface and removal of existing paint flakes, to obtain an even surface ,necessary tools and machinery to give an even shade. Application to be done only by applicator authorised by manufacturer, also shall be approved by GE before starting of work.

M&L for applying two coats of Tractor Suprema Acrylic Distemper on new surfaces of wall/ceiling with Graco spray machine over a coat of primer complete all as specified and directed.

M&L for applying one coat of Tractor Suprema Acrylic Distemper on old surfaces of wall/ceiling with Graco spray machine complete all as specified and directed.

M&L for chipping out spilled and loose concrete cover and derusting steel reinforcement of concrete column, beam, slab, chajjas, parapets and the like as directed up to 25 to 35mm thick roughening and cleaning concrete surface with steel wire brushes, washed with water and allowed to dry including derusting steel wire reinforcement, providing fabric MS wire mesh 75 x 75 x 2mm as reinforcement to concrete surface applying adhesive/admixture over steel mesh and providing 25mm average thickness guniting mix using one part of OPC 53 grade and two part of sand mixed with adhesive/admixture @ pressure of 2.5 to 3.00kg/Sqcm by guiniting machine and surface finished even and fair including necessary padding, shuttering/scaffolding, formwork (guniting work to be carried out up to 10 metre height) complete all as specified and as directed at site Notes :- (a) After placing the additional reinforcement all concrete surfaces shall be thoroughly scrubbed with wire brushes, washed with water and allow to dry, apply chemistic polycretes admixture @ 2.25 kg by weight of cement all as per manufacturers instruction. (b) when polymix concreting in taking condition,guiniting is done with polycrete admixture @ 2% by weight of cement all as per manufacturers instructions (polycrete admixture shall be procured from chemical adhesive Pvt Ltd Co or their authorised dealer). (c) Cost of the above aspect shall be deemed to be included in the quoted rate of the respective item and nothing extra shall be paid on any account.

Demolition of RCC of any description, in any position roofs, floors (other than ground floors), beams staircases, landing, chajjas, RCC overhead tank and similar suspended work and Removing excavated material /demolition material exc. 1.50 km but n exc.5 km including taking down from upto four storey complete all as specified and as directed.

M&L for form work to chajjas, parapets and similar items including edges thick finished rough complete all as specified and as directed.

M&L for RCC 1 : 1.5 : 3 type B1 using 20mm graded stone agg as in chajjas complete all as specified and as directed.

S&F 10mm dia TMT bar as in reinforcement of RCC of any description cut to length bent to shape required including cranking, bending, binding with MS wire not less than 0.90mm dia complete all as specified and as directed.

S&F 8mm dia TMT bar as in reinforcement of RCC of any description cut to length bent to shape required including cranking, bending, binding with MS wire not less than 0.90mm dia complete all as specified and as directed.

Dismantling Bricks (laid flat or on edge) or brick tiles in floors, roof, channels, kerbs, aprons, etc. (each layer complete all as specified and as directed.

Demolition Mud in roofs, any thickness, including plastering and lapping (whether full thickness removed or only a part thereof) complete all as specified and as directed.

Removing soil excavated material exc. 1.5Km but n exc 5km and depositing where directed at above the starting point complete all as specified and as directed.

M&L for cement concrete 1:2:4, type B0 (using 12.5 mm graded stone aggregate) on roof padding surface finished even and smooth without using extra cement complete all as specified and as directed.

M & L for screed bed 10 mm thick (average) plaster on concrete surfaces in CM (1:3) on roof, mixed with water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed (Water proofing compound shall be measured and paid seperately).

M&L for APP based polymeric membrane plain finish minimum weighting 3 kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150 gms/sqm) over one coat of 85/25 bitumen @1.2 kg/sqm and paste the membrane with torching method and again apply a coat of 85/25 bitumen @ 1.2 kg/sqm at overlapping joints complete all as specified and as directed.

M&L for preparation of new surface of APP membrane and applying two coats of aluminium paint at surfaces of any description, over 10cm in width or girth, not otherwise described complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in any description and in any position not otherwise specially provided for complete all as specified and as directed.

M&L for Providing cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered and hold fast on edge including necessary form work complete.

S&F PVC wall panelling plastic section for wall panelling of 5 mm thick fixed with 5 mm thick PVC sheet fillets of width 35 mm for wall paneling and fixed to wall to make PVC frame as per specification and drawing wall complete all as specified and as directed.

S&F one piece EWCs with seat cover and twin flush cruiser snow white colour size 710x390x790mm Strap including all fitting. complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S & F table top wash basin of size 650x380x110mm catmax snow white colour including all fittings complete all as specified and as directed. Make :-CERA Cat No.- S2020159 or equavilent.

S&F waste coupling with ceramic pop-up full thread 32mm for WHB complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F bottle trap of size 228 mm for WHB complete all as specified and as directed.(Make- CERA)

S&F angle cock fancy type cast copper alloy,screwed down,high pressure,with crutch orbutterfly handle,screwed bothends for iron pipe or fo runions and fixed to15mm bore pipe complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F CP pillar cock mixer 2-in-1 for wash basin with all fittings complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F CP Bib cock with wall flange and single knobs with all fittings complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F CP wall mixer 3-in-1 with wall flange with all fittings complete all as specified and as directed. (Make- CERA Cat No.F1002401)

S&F 15 mm CP Bib cock 2 way with wall flange and single knobs with all fittings complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F Shower panel SWR PNL jaq anti finger print stainless steel finish 1400x 200mm complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F CP Health Faucet ABS body (Push type) with wall hook and 1.0 mtr SS Braded rubber hose pipe complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F Corner glass shelf 300x300 mm with 'D' / F type brackets complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S & F Soap dish complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S & F Liquid Soap dispenser complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S & F toilet paper holder complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F SS Towel rack 600mm long fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F SS Towel rail 450mm long fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. (Make :- Jaquar, CERA, Kohler)

S&F 12mm toughened glass with frosted sun film partition in bathing area with door sliding/openable as rqd with all necessary fittings i.e. handle, clits for smooth functioning, locking arrangement and top/sides are fixed as required with wall complet all as specified and as directed.

Note :- (i) The contract sum shall be after deducting the amount of Credit shown in Sch of Credit of this Tender. (ii) If any item of same description in nature is found to be entered as "double in BOQ" and the bidder quotes different rates against same item, then the rate quoted on lower side shall be applicable and higher rate will not be allowed to be paid in any circumstances. No claims on this account shall be entertained on a later date.

PG CONSTRUCTION AND COMPANY (BID ID -3106462)

JINDAL ENTERPRISES (BID ID -3101050)

M/S Parmod Johar (BID ID -3104333)