JH XIV_III_SIM-02

Amount

1. Remaining work of Construction and Maintenance of Karamunda to Mararoma Ganjhutoli (L- 2.83 Km)

Setting out Pillars Providing & fixing of Bench Mark pillars @ four nos. per km as per drawings given.

Construction of embankment with approved material obtained from borrow pits with a lift up to 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with free lead as per Technical Specification Clause 301.5

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead up to 500 m as per Technical Specification Clause 303.1.For Flexible Pavement

Construction of earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead up to 1000 m as per Technical Specification Clause 303.1. For Flexible Pavement

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader /tractor mount grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading III Material

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with three wheel 80-100 kN static roller in stages to proper grade and camber, applying and brooming, crushable screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508.

Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510

Construction of un-reinforced, dowel jointed at expansion and construction joint only, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, dowel bars, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days using curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification Clause 1501

Road Furnitures, K.M. Stones, Traffic & Direction Sign, PMGSY Logo, Citizen Information Board Reinforced cement concrete M15 grade kilometre stone/local stone of standard design as per IRC:8 fixing in position including painting and printing, etc. as per drawing and Technical Specification Clause 1703 (i) 5th Kilometre Stone (precast). 200m Stone (precast)

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2

Providing and erecting direction and place identifications of semi reflective sign boards as per IRC:67 made of 2 mm thick M.S. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour. Supported and welded on 47 mm x 47mm of 12 SWG Square tube of 3050 mm height duly strengthened by 25 mm x 5 mm M/s flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701

Providing and fixing of typical PMGSY informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1

Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704

Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out,construction of shorting and bracing, removal of stumps and other deleterious matte, dressing of sides and bottom and backfilling with approved material.

Bedding for Pipe Type B (First Class) Bedding : Laying (First Class) bedding on well compacted sand, moorum or approved granular material as per Clause 1105 (ii)

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in single Row Providing and laying reinforced concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 excluding excavation, protection works, backfilling, concrete and masonry work in head walls and parapets as per Clause 1106.

Providing and laying boulder soling in foundation with stone boulders of minimum size & weight as per table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications clause 1301.

Plain Cement Concrete M10 (1:3:6 niminal mix) in levelling course below open foundation of Head walls as per drawings & Tech. Specification Clause 1109

Stone masonry work in cement mortar in foundation complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203.

Pointing with cement mortar (1:3) on stonework in substructure as per technical specification Clauses 613.4 & 1204

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of item A) and disposal of excavated earth as obtained to a distance upto 50M including 1.5 lift, levelling, ramming the foundation trenches, removing roots of tree shrub A. Hard soil 75%

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of item A) and disposal of excavated earth as obtained to a distance upto 50M including 1.5 lift, levelling, ramming the foundation trenches, removing roots of tree shrub B. Soft Rock 25%

Providing P.C.C. M-100 with nominal mix (1:3:6) M100 in foundation with approved quality of stone chips of 20 mm to 6 mm size and clean coarse sand of FM 2.5 to 3 including screening, mixing cement concrete in mixer and placing in position, vibrating,

Providing rough dressed coarse stone masonary in C.M. (1:4) in foundation and plinth with hammer dressed stone of less than 0.03 m3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening, racking out joints to 20mm depth curing, taxe

Providing rough dressed coarse stone masonary in C.M. (1:4) in superstructure with hammer dressed stone of less than 0.03 m3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening, racking out joints to 20mm depth curing, taxes and r

Providing PCC & R.C.C. M-300 in Wearing cost with nominal mix with approved quality of stone chips 20mm to 6 mm size ( 2 parts of 20mm to 10mm to 6mm) and clean coarse and sand of F.M 2.5 to 3.5 in foundation and plinth including mixing cement concrete

Providing C,P (1:3) in cement on stone masonary with clean coarse sand of F.M. 1.5 including screening and curing with all leads and lifts of water, scaffolding, taxes and royalties all complete job as per building specification and direction of E/I.

Earthwork in back filling in foundation trenches and plinth in layers not exceeding 1500mm thick well watered, rammed, fully compacted and fine dressed with earth obtained afer cutting within a lead of 50 M and lift of 1.5 M all complete job as per buildi

Providing weep holes with day grades stone filter of 53mm to 22.4 mm size in abutment and wing wall all complete job as per specification and directioni of E/I.

Providing P.C.C. & R.C.C. M-150 with nominal mix (1:1½:3) with approved quality of stone chips 20mm to 6 mm size and clean coarse and sand of F.M 2.5 to 3.5 in foundation and plinth including mixing cement concrete in mixer, screening, all taxes and roya

1st Year Maintenance

2nd Year Maintenance

3rd Year Maintenance

4th Year Maintenance

5th Year Maintenance

Labour Cess @ 1%

dikshit shreya construction private limited