SPL REPAIR TO BLDG No. NP-02 AND ADDL/ALTN TOILET BLOCK TO BLDG No. NP-02 AND NP-23 OF 21 SUB AREA UNDER GE (WEST) PATHANKOT

Amount

Sch 'A' Part-I B/R Part:- Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar including all quions, wall, arches, pillars, man-holes, drain etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area not exc1.5 Sqm each and removing from site complete all as specified and directed.

Taking down chowkhats or frames exc 1.50 and n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed.

M & L for burnt clay brick work with sub-class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per srl item No.6 here-in-before but except brick retrived from item No. 01

M&L for Brickwork with fly ash brick straight or curved to plan in any radius in half brick wall built in cement mortar 1:4 complet all as specified

S&F factory made Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F Steel window/ventilator factory made, made out of mild steel box type and shutter suitable for double shutter i.e. Glazed and gauged shutter. Glazed shutter made out of hollow' section with sash bar and gauged shutter made out of hollow section without sash bar including hinges, tower bolt, handle, grill 10 mm sq bar including two coat of synthetic enamel paint over one coat of red oxide primer, tarred hold fasts, PCC bed blocks for fixing hold fast, including plain/figured glass 3mm thick and stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.18mm & fixed with stainless steel wire staples`etc complete all as per details shown in drawing No CEPZ/C-TD/032/13 sheet No 1/2 & 2/2 including taking down existing spoiled and unserviceable windows/ventilators of any type ( wooden/steel) complete all as specified and directed

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & F 300mm long Aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminum alloy and fixed complete all as specified and directed.

S & F 150mm long aluminum, anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S&F 150mm long extruded aluminium alloy handles, cast type, anodised

Taking up or down 15mm bore, steel tubing and connection including cleaning for refixing or removal from site complete all as specified and directed.

S & F 15mm bore Steel water tubing 'medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F Rotational moulded polyethylene water storage tanks of 1000 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm dia ball vale high pressure of PTMT with epoxy coted aluminium rod & high density plastic ball screwed for iron pipe and fixing inlet, outlet & over flow pipe etc. including dismantling of old PVC/RCC water tanks complete all as specified and directed.

S&F in repair for 15 mm bore chromium plated fancy type Bib taps, cast copper alloy with crutch or above butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed (minimum weight 575 grams) complete all as specified and directed.

S&F in repair 15mm bore Stop valves/Angle Valve, fancy type, chromium plated with long shank and cup (concealed type),cast copper alloy, screwed down, high pressure, with crutch or above butterfly handle, screwed both ends for iron pipe or for unions and fixed (minimum weight 575 grams) complete all as specified and directed.

S&F in repair Stainless Steel Soap Dish or Soap Holder Dish for Bathroom with fixing arrangement complete all as specified and as directed.

S & F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repair floor mounting single piece vitreous china wash down water closet pan, light colour complete including fixing to trap, alongwith PP soft close seat cover, hinges and accessories complete all as specified and as directed.

S&F in repair Hand Shower (Health Faucet) with 8 mm dia,1.2 m long Flexible Tube Chrome Finish & Wall Hook for Water closet complete all as specified and directed. Make:- Jaquar Cat No Health Faucet SKU ALD-573 or equivalent in any of the make metnioned in list of product.

S & F in repair 15mm bore dia wash hand basin Brass CP mixer for mixing hot & cold water with 450mm long braided house 20 cartriage size screwed down for iron pipe complete all as specified and directed.

S&F in repair Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, , flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and cp brass spreder all necessary fittings, complete all as specified and directed.

S&F in repair Vitreous China Urinal, full stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, , flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and cp brass spreder all necessary fittings, complete all as specified and directed.

S & F in repair glass corner shelf quarter round with CP brass bracket fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed.

S & F in repair brass chromium plated shower roses 125mm size with or without swivel joints including fixing to steel pipe or union complete all as specified and directed by Engr-in-charge.

S&F in repair 15 mm dia Pillar cock, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts.

S&F in repair CP brass towel ring 20mm dia, fancy type, superior quality, fixed with and including chromium plated screws and wooden/plastic cleats complete all as specified and directed. Make : ACN-1121BN of JAQUAR or equivalent in any of the make mentioned in list of products.

S & F in repair 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,fush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed.

S&F in repairs Vitreous china wash basin,counter sunk of size 550 x 400 mm, including cutting for and pinning in ends of brackets or erecting stand including 32 mm bore CP waste pipe long screw thread and 32 mm dia flexible waste pipe incl fixing of taps all as spd and directed.

S & F in repair 15mm dia PVC connections 450mm long with PTMT nuts complete all as specified and directed.

M & L for Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

M & L for Glazed ceramic Coloured tiles in vertical/dado surface 450mmx300mmx7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and directed.

M & L for Vitrified Ceramic tiles 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc (size of each tile 0.6m x 0.6m), set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

All as per srl item No 38.00 here-in-before but as in vertical/skirting surface etc over and including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and directed.

Use and waste of formwork to soffits of concrete fair finished surfaces of suspended slabs such as roof slab,floor slabs landings and similar works not exc 200 mm thick complete all as specified and directed.

M & L for Reinforced cement concrete nominal mix(Type B-1, 1:2:4 using 20mm graded crushed stone aggregates) in slabs supported on walls beams, columns in floors, roofs, landings, balconies, canopies, deck slab and shelves etc.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for 18-20mm thick granite (pure black) work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite over including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L for Rendering 5 mm thick plaster in cement mortar 1: 3 on concrete surfaces as in ceilings finished even and smooth without using extra cement, complete all as specified.

M & L for rendering 10mm thick in CM 1:6 on brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15mm thick in CM 1:6 including mixing with liquid water proofing compound @200ml per bag cement on brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded crushed stone aggregate as in , plinth protection and surface finished even and fair with out using extra cement including making joints at every 2.5m and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight all as specified and as directed.

M&L for Preparation of newly plastered surface of wall and applying two coat of oil bound distemper, white or tinted shade with and including priming surface with chalk whitening , complete all as specified.

M & L for preparation of newly plastered surfaces of wall and applying minimum 02mm thick white cement based wall care putty on wall surfaces & making smooth surface and applying two coat of distemper oil emulsion over and including one coat of primer complete all as specified and directed.

M & L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall/edging/facia/roof projections and applying two coat of exterior weather coat paint, white or tinted or green over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment of old plastered or unplastered decorated surface of wall(internal) by brooming down from steel wire brush, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying two coat of distemper oil emulsion over and including 2mm thick wall care putty and making the surface smooth complete all as specified and directed.

M &L for preparation of old surface of ceiling and applying one coat of white wash complete all as specified and as directed.

Taking down existing roof treatment of any description incl mud phuksha or PCC pedding if any (any no of layers) incl brick tiles , terracing tiles if any including removal to dabries in low laying area exc 1.00 KM but n exc 2.00 KM complete all as directed.

M&L PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in roof kerbs or mub stop/ leveling course on existing roof or sunken floor of toilet portion, rounded and chamfered on edges, complete all as spd and directed

M&L for 20mm thick cement plaster in cement mortar 1:4 on concrete surface finished even and smooth including with WPC liquid of make Dr. Fixit or STP as per manufacturer instruction @ 0.200 ltr in per bag of cement.

APP modified roof treatment over existing non-accessible RCC roof slab/chajjah/canopy/parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc complete all as specified and directed :- (a) Cleaning the top surface of RCC roofing properly with water complete. (b) Applying Oil bound bitumen primer @ 0.30 liter/Sqm manufacture by the same agency as that of APP with a density 0.87-0.89 Kg per liter at 25 degree centigrade on prepared surface. (c) Laying of membrane not less than 3.0 mm thick APP modified water proofing membrane weighing not less than 3.00 Kg/Sqm reinforced with non woven polyster fiber weight not less than 150 Gms/Sqm using butane torch by torch application with 10 Cm side laps and 15 Cm end lap complete. (d) APP membrane shall be laid using butane torch by Torch application with minimum 10cm side overlap and 15cm end lap. (e) Top of membrane shall be provide with solar reflective bituminous aluminum paint @ 0.1 Kg /Sqm as prescribed by manufacture of membrane. (f) APP Membrane shall be stick inside parapet where available by chase cutting and sealed with PCC (1:2:4) type B-0 complete.

S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F in repair 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors

S&F in repair 110mm dia PVC (SWR) bends any radius

S&F in repair 75mm dia PVC (SWR) bends any radius

S&F in repair 75mm bore PVC (SWR) floor trap, plain with grating including including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 with CP grating complete all as specified & directed.

Demolition of cement concrete (unreinforced) etc in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L for 25mm thick Cement concrete in sub base concrete using Type B-0,1:2:4 (using 12.5 mm graded crushed stone aggregate) Finishing surfaces of concrete to be even and rough to receive the topping layer or floor tiles etc. complete all as specified and directed.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions frame workwith hollow section. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F powder coated (thickness of powder coating not less than 50 micron) aluminium door shutters, aluminium section weighing 0.55 kg/m including powder coated door frame/chowkhat (not less than 1.25 mm and not less than 85 mm width) including necessary joining cleats, glazing clips, rubber neoprene packing, handles (150mm) 02 Nos in each door, hinges (100 mm) 03 Nos in each door, powder coated aluminum snap beading screws etc. complete all as specified and directed by Engr-in-Charge.

S&F powder coated (thickness of powder coating not less than 50 micron) aluminium window and ventilator shutters, rolling/sliding type without sash bar, aluminium section weighing 0.55 kg/m including powder coated window/ventilator frame/chowkhat (not less than 1.25 mm and not less than 85 mm width) including necessary joining cleats, glazing clips, rubber neoprene packing, handles 01 Nos , hinges, powder coated aluminum snap beading screws, rolling wheel etc. complete all as specified and directed by Engr-in-Charge

S&F in repair Door closer hydraulically regulated, designation No. 1,universal type, suitable for door shutters of 700mm in width and of weight between 35 kg and fixed aluminium (Diecast) body complete all as specified and directed.

S & F in repair 25mm outer dia stainless steel bright finished ,fancy type decorative drapery rod of thickness 20 gauge with ends caps in (pair) fixed to wall with screws ,PVC gully including all necessary fixing arrangement including taking down old curtain rod complete all as specified and directed.

Demolition of RCC of any description slab , shelves , chajjas, water tank ,chullah hoods etc and in any position including cutting reinforced as required complete all as specified and directed.

S&F in repair Towel Rack size 50.2x36.6x5.8cm with 4 double cross towel hook and swivel towel bar , Stainless Steel complete all as specified and directed.

M & L for 5mm thick Coloured/ printed Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing at site incl demolition of existing lining of any description complete all as specified and directed.

M&L for 12mm thick Seamless calcium silicate ceiling made out of 1800 x 1200 mm size board of siliceous and calcareous material reinforced with cellulose fibre fixed to the ceiling section with 25 mm long self drilling and tapping screws having phillips head with under head cutter at 200 mm centre to centre, including finshing the joint of face board with specially formulated jointing compound and 48 mm wide fibre tape to provide seam less finish including Gl frame work of grid size 605 x 605 mm for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre and Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including taking down old U/s ceiling or ceiling board complete all as specified

Cleaning of grass, vegetation growth/saplings growth/saplings growth after uprooting from roof top/wall completely including making good disturbed surfaces in CM 1:4 to match the existing complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position including Cleaning with bleaching powder and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. and including providing of new GI fittings, inlet/outlet washout, overflow pipe, long nipples, checknuts & washers etc. complete all as specified and as directed.

S&F in repair 10mm thick transparent toughened sheet glass as in door shutters/partitions including necessary packing and jointing material fixed to wall opening with suitable metal/aluminium/wooden frame including provn of floor spring complete in all respect including all connected accessories and handles complete all as specified and as directed.

M&L for HDF laminated AC2 wooden floor tile of 8 mm thick with dove tailed joints laid over 150 micron polythene film and 3mm thick foam as per manufacturer instructions including laying of tiles at skirting portion with moulding also including dismantling existing floor tiles and make the surface perfectly leveled and clean before laying of tiles including locking the tiles at the door openings, gola complete all as specified and as directed.

M&L for precast cement concrete designer louvres and jallies, of size 20cm x 20cm and 35mm thick (measured solid) of approved shape and pattern of 1:2:4, type B-0(using 12.5mm thick crushed stone aggregate) set using adhesive including dismantling of old RCC jalli complete all as specified and as directed.

Sch 'A' Part-I E/M Part:- M&L for modular point wiring for one light/one fan controlled by one switch with 1.5 Sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable with and including PVC rigid concealed conduit heavy duty suitable size with all accessories having thickness not less than 1.8 mm including modular matallic flush box of suitable way with modular cover plate for modular switches and sockets , including green 1.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface including taking down old u/s point wiring complete all as specified and directed.

All as per Srl item No. 80 here-in-before but modular 3 pin 5 Amps socket outlet on the independent board with other switch complete all as specified and directed.

All as per Srl item No. 80 here-in-before but modular 3 pin 5 Amps socket outlet on the same board with other switch complete all as specified and directed.

M&L for modular point wiring with 2.5 Sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable with and including PVC rigid concealed conduit heavy duty suitable size with all accessories having thickness not less than 1.8 mm including modular matallic flush box of suitable way with modular cover plate for modular switches and sockets , including green 2.5 sqmm PVC insulated unsheathed multistrand copper conductor FRLS cable as earth continuity conductor connected to comman earth dolly, including cutting chiseling for concealed piping and making good disturbed surface to match with the existing surface including taking down old u/s point wiring complete all as specified and directed.

S&F in repair Modular switch 1 way 6 A, 1 module complete all as specified and directed.

S&F in repair Modular switch 1 way 16A, 1 module complete all as specified and directed.

S&F in repair Modular Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

S&F in repair Modular Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S&F in replacement of existing unsv sheet metal enclosure with sheet metal enclosure MCB distribution board single pole and neutral with a two pin and earth plug and socket 20 amps 240 volts, complete with one single pole MCB of 20 amps 'C' curve complete all as specified and directed .

S&F in repair ceiling rose, PVC/polycorbonate, insulated body, surface backelite 65mm dia three terminals complete all as specified and directed .

S&F in replacement LED slim panel (2 in 1, cool white and warm white type) 12W LED ceiling round 6" light fitting 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver holder & LED Lamp suitable for roof ceiling including connecting up with driver three core flaxible copper conductor of suitable size from ceilling rose/PVC connector to light fittings complete all as spd and directed by Engr -in -charge.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 12 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 8 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S & F in replacement of sheet metal enclosure MCB distribution board, double door with IP-43 protection single phase 240 volts 6 way, including suitable size copper bus bar and neutral link fixed flush in wall including chases in wall for fixing DB and making good the distributed wall surfaces to match with existing specification complete all as specified and directed.

S&F in replacement for MCB SP 240 volts of rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement for MCB SPN 240 volts of rating from 6 to 40 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement for MCB SPN 240 volts of rating 63 amps, 'C' cruve with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S & F in replacement bldg secuirty light fitting energy saving high efficiency LED street light fitting 35 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 25 mm dia bent to shape having length on less than 0.9 mtr fixing with clamp etc and making connections using suitable size copper cable from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage.

S&F in replacement sub Main Wiring with two PVC insulated unsheathed multistrand FRLS flexible copper conductor cable of size 2x4 sqmm and one PVC insulated multistrand unsheathed FRLS flexible copper conductor cable of size 4 sqmm (green colour) as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia complete and making good to disturbed surface complete of wall/floor with cement mortar and finishes to match the existing surface complete all as specified and directed.

S&F in replacement sub Main Wiring with two PVC insulated unsheathed multistrand FRLS flexible copper conductor cable of size 2x6 sqmm and one PVC insulated multistrand unsheathed FRLS flexible copper conductor cable of size 6 sqmm (green colour) as earthing lead connecting to main earthing dolly drawn in and including non metallic PVC concealed conduit 20mm dia complete and making good to disturbed surface complete of wall/floor with cement mortar and finishes to match the existing surface complete all as specified and directed.

S & F in replacement of old unsv sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways vertical TPN DB for comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following (a) MCCB FOUR POLE 100 AMPS AC 415 VOLTS 25 KA=01 NO as incoming and 12 nos. MCB SP 40 Amps, C series as outgoing. ( (i) MCCB, MCB and DB should be of same make. (ii) The DB shall be flush fixed ,and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of theMCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble -properly crimped.(iv) all the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) double continuous earth wire shall be provided for each three phase DB from earthing mains dolly.

M & L for earthing complete with galvanised steel earth plate electrode , 600 x600 x 6mm thick burried directly in the ground (earth pit not less than 2.25 mtr deep below ground level)with top edge of the plate not less than 1.5mtr below ground level connected to galvanised iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point , GI tubing 15 mm bore light grade protection pipe , GI watering pipe 20mm bore light grade with funnel and wire mesh , charcoal ,salt packed around the earth plate and precast PCC 1:2:4 (Nominal mix ) reinforced with XPM having weight not less than 4 kg /sqm including suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover including earth work in any type of soil , removal of surplus soil to a distance n.exc 50m and connecting , testing on completion complete all as shown on electric plate No 03 of SSR -2009 Part I complete all as specified and directed.(Note: Excavation and earth work is deemed to be included in the rates quoted).

Note:-The accepted amount will be arrived after deducting the Sch of credit i.e. Rs 53,203.00 and any other reduction if any from quoted amount.

M/S SATYA SAI CONSTRUCTION (BID ID -3384277)

Ambika Construction Co (BID ID -3384191)

M/S RUDRA CONSTRUCTION CO (BID ID -3384518)

HARI OM ENTERPRISES (BID ID -3384666)

malghotra construction co (BID ID -3384751)

VAISHNAVI BUILDERS (BID ID -3384812)

M/S Raghuvanshi Builders (BID ID -3384683)

M/S TARSEM CHAND AND SONS (BID ID -3385108)