REPAIR TO REPLACEMENT OF OLD CONVENTIONAL STREET LIGHT FITTINGS WITH ENERGY EFFICIENT LED FITTINGS AT VARIOUS LOCATIONS UNDER GE (MCTE) MHOW

Amount

Excavation in trenches not exc. 1.5m wide and not exc 1.5m deep in hard/dense soil and getting out complete all as specified and directed by Engr-in-Charge.

All as per Srl item No.1 above, but depth exc 1.5m and not exc 3.0m deep.

Returning filling in trenches including spreading, leveling, watering and well ramming in layers not exceeding 25 cm thick in any type of soil complete all as specified and directed.

Removing surplus excavated material to a distance not exc 50m and depositing where directed at a level not exc 1.50m above the starting point complete all as specified and directed.

M&L for filling approved fine river sand in trenches as cable cushion to the full width of excavated trench, under and over cable complete all as specified and as directed. (Note : Punned thickness of sand shall be measured)

M&L for bricks slightly over burnt (kiln burnt), modular bricks, best quality, locally available, laid flat, dry, laid in trenches along the length of cable transvarsally with width equal to length of brick for cable protection all as specified and as directed.

Supply and fixing LED street light fittings lumanaries 90 watt LED with lens, pressure die cast epoxy powder coated aluminium housing with efficient designed heat shrink with heat resistant toughned glass with frame fixed with SS Screws suitable for fixing in existing poles, with protection IP-66, power factor not less than 0.95, surge 5KV, total harmonic distortion THD is < 10% lumen not less than 100 lumen/watts complete, including dismantling of old one fittings, all as specified and directed by Engr-in-charge.

All as per Srl item No.7 above but capacity 60 Watts.

All as per Srl item No.7 above but capacity 45 Watts.

S&F in replacement of LED flood light fittings 120 Watt die cast aluminium housing with separate LED and driver compartment, Rectangular LED Flood Light with innovative thermal management and available in multiple optics and equipped with IP66 protection, in built electonic LED driver.

All as per Srl item No.10 above but 150 Watt.

All as per Srl item No.10 above but 200 Watt,

S&F in replacement of LED driver suitable for 90 watt LED light fitting of any make, including taking down old one from existing fittings.

S&F in replacement of LED driver suitable for 72 watt LED light fitting of any make, including taking down old one from existing fittings.

S&F in replacement of LED driver suitable for 60 watt LED light fitting of any make including taking down old one from existing fittings.

S&F in replacement of brackets for street light fitting fabricated out of 40mm bore GI tube, light grade, 1500mm long, made to shape and drilled holes etc, fixed to poles with suitable MS clamps fabricated from 40mm x 5 mm MS flat duly painted in two coats of anti corrossive aluminium paint over a coat of red oxide zinc chrome primer and fixed with suitable sizes of bolts, nuts and washers and taking out old bracket of any length and shape all as specifed and as directed.

S&F GI tubing, light grade, 50 mm bore pipe laid in trenches/duct or in road crossing or fixed to wall/poles for protection of cable complete all as specified and direct.

All as per Srl item No.17 above but 40 mm bore pipe.

Sppply & Laying XLPE insulated, armoured, electric cable with aluminium conductor, 1100 volts grade, laid in trenches, fixed on poles/walls or passing through pipes including provision of necessary lugs and glands & making necessary connection including taking down old unservicable cable of any core complete all as specified and directed, for the following :-

(a) 10 Sqmm 2 core.

(b) 10 Sqmm 4 core.

(c) 16 sqmm 4 core

(d) 25 sqmm 3.5 core

Supply and fixing sheet moulding compound (SMC) junction box, suitable for terminating 2 Nos 4 x 10/16 Sqmm UG cable, including of one in Nos MCB SP 10A, 240 volts, AC, 50 Hz, including cable glandes- 2 Nos, 4 Nos of AL bus bar with 3 nos hols for cable connection, two way connector 1 No. Make : Sintex (Model No GSJB3020)/ Finolex/ Universal.

Cutting the existing bituminuos road for passing of UG Cable in road crossing and making good the disturbed surface of road to its original specification complete all as directed.

Cutting, trimming and prunning of trees/tree branches of any girth upto 2.5 m all around existing LT over head lines / sourrounding street light and flood fitting including cleaning the area beneath the LT overhead lines and removing the debris from the site and depositing where directed.

S&F in replacement of sensor of timer switch alongwith pre-dawn switching off timer, 4-8 Hrs (nature switch) single phase, confirms to IP 64 degree of protection all as specified and directed. Make : Kakatiya Energy Systems Ltd. Model No - Nature switch-02

S&F in replacement of Automatic Street Light control switch for three phase load of 5 KW, using Infrared Sensor based NATURE SWITCH for automatic switching of street light. Nature Switch operation should be based on Natural Light Lux level. Required illuminance level for switching ON is ≤ 30 Lux and for switching OFF ≥ 10 Lux. The sensor should also have part night operation facility of min. 4 hrs to max. 12 hrs. The Sensor along with 03 Nos contactors each of 20 to 25 Amps capacity, Incoming MCBs and Outgoing MCBs of 20-25 Amps (03 Nos) and auto/manual operation (Senser by Pass), size of circuit wiring should be multistranded FRLS min size of 10 Sqmm should be enclosed in a pole/wall mounted enclosure made of rust proof, Electric shock Proof, Termite proof and FR grade SMC Junction box conforming to IP54 and model Swadeep 02EC5KW3P complete all as specified and directed. Make : Nature Switch - Kakatiya Energy systems/Legrand/ABB (ii) Contactor - BCH/L&T/Schneider (iii) MCB -L&T/ Schneider/HAGER

All as per item No.24 above but for single phase model 02EC5kW1P including Sensor along with 01 Nos contactors 25 to 40 Amps capacity, Incoming MCBs and Outgoing MCBs of 25 to 40 Amps (01 Nos).

M&L for wiring with 1.5 sqmm 2 runs of single core multistrand PVC insulated, unsheathed cable with 1x1.5 sqmm earth wire conforming to IS - 694, 1100 volts with copper conductor drawn in and including 20 mm dia or higher, non metalic PVC grey conduit with all accessories such as Tees, Elbows, Junction box, Reducers etc as required and connecting to existing main switch board / distribution board to fittings and testing on completion incl taking down old wiring complete all as specified and as directed. Note : 2 runs of 1.5 sqmm with 1x1.5 sqmm earth wire cable and conduit will be measured as one unit i,e. 1 RM.

S&F in replacement of MCCB, 4 pole, fixed type, 415 Volts 63 Amps capacity, 16 KA rating rupturing capacity including taking out old unserviceable MCCB of any type and make complete all as specified and directed.

S&F in replacement of MCCB, 4 pole, fixed type, 415 Volts 100 Amps capacity, 18 KA rating rupturing capacity including taking out old unserviceable MCCB of any type and make complete all as specified and directed.

S&F in replacement of MCB, Single Pole 10-32 Amps, B Series, rapturing capacity 10 KA, 240 volts AC, including dismantling of old one. Make : Legrand/ABB/C&S/Havells/Indoasian

S&F in replacement of MCB, SPN 10-32 Amps, B Series, rapturing capacity 10 KA, 240 volts AC, including dismantling of old one. Make : Legrand/ABB/C&S/Havells/Indoasian.

S&F in replacement of MCB, TPN 32 Amps capacity B Series, rapturing capacity 10 KA including dismantling of old one. Make : Legrand/ABB/C&S/Havells/Indoasian

S&F in replacement of MCB, TPN 63 Amps capacity B Series, rapturing capacity 10 KA including dismantling of old one. Make : Legrand/ABB/C&S/Havells/Indoasian

S & F Maple type decorative LED POST Top lanterns fittings capacity 40 watts made in cast aluminium spigot housing with decorative clear acrylic diffuser and IP65 protection Milky version comprising of clear/opal acrylic bowl with built in ribs, brown powder coated cast aluminium spigot complete with accesseries and brown powder coated sheet alumini cover fixed on top with decorative knob complete with 40 W LED including making necessary electrric connection to the fitting with suitable size flexible copper cable including dismantling and taking out old one all as specified and directed. Make : Cat part No LPTO-40-CDL of Crompton or equivalent in Philips/Wipro

S&F PVC sheathed 1100V grade weather proof, flat, twin core stranded aluminium conductor of size 4 Sqmm.

S&F PVC sheathed 1100V grade weather proof, flat, twin core stranded aluminium conductor of size 6 Sqmm.

S&F PVC sheathed 1100V grade, weather proof, flat, twin core stranded aluminium conductor of size 10 Sqmm.

S&F in replacement of power contactor three phase 40 Amps 2 NO + 2 NC for nature switch. Make : Legrand/L&T/ Havells

S&F in replacement of power contactor three phase 65 Amps 2 NO + 2 NC for nature switch. Make : Legrand/L&T/ Havells

Repairs of existing street / security light fittings, any type and wattage, taking down and refixing on LT pole after refreshing of connection & testing complete all as specified and directed.

Taking down damaged PCC pole of any size embedded in concrete all as specified and directed. Note :- Excavation and earth work will be measured and paid for separately under relevant items. Cost of demolition of PCC shall be deemed to include in the rate quoted under this item.

M&L for steel tubular swaged poles complete with MS base plate, finial taper plug, bolts, nuts & screws type 410, SP-31 (9 mtrs long), erected to truely vertical position, painting externaly embedded portion in PCC with black bitumenous paint and externally exposed to view portion with aluminium paint in two coats, making five alternate strips 30cm wide with black and yellow paint in two coats, marking MES number with black paint complete all as specified and directed. (Note : Excavation and PCC will be measured and paid separately under respective items).

M&L for PCC 1:4:8, type D2 ( using 40 mm graded crushed stone aggregate) as in base foundation of the pole, all as specified and directed.

M&L for PCC 1:3:6, type C2 (using 40 mm graded crushed stone aggregate) as in foundation and mass filling for poles, stays etc all as directed and as specified.

M & L for PCC 1:2:4 type B1 using (20mm graded crushed stone aggregate) as in coping of poles including necessary form work and finishing exposed surfaces complete all as specified and directed.

Ms Kailash Chandra Babulal

S.S. Engineers

Mighty Steel Sales Crop

AGARWAL BUILDERS