Renovation of existing toilets, Allied I.E. works and indoor lighting and Shade works at PM Shri Kendriya Vidyalaya, Sector-5, Dwarka, New Delhi

S.No. Description of Work Amount (INR)

1 Renovation of exisiing toilets except IE works and indoor lighting 73,50,215.26

2 Allied I.E. works and indoor lighting peretaining to toilet renovation 14,97,920.00

3 Shade works 55,82,617.10

Digitally signed by AMIT

Sr. No. DSR ref. Description Unit Quantity Unit Rate Amount

1 2.6 Earth work in excavation by mechanical means (Hydraulic

excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m

in width as well as 10 sqm on plan) including getting out and disposal of

excavated earth lead upto 50 m and lift upto 1.5 m, as directed by

Engineer-in-charge.

1 2.6.1 a) All kinds of soil

2 2.25 Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming and watering, lead up to

3 1.1.2 Carriage of earth by mechanical transport including loading, unloading

for a lead upto 10.00 Km. Cum 14.85 442.48 6,570.83

4 2.27 Supplying and filling in plinth with sand under floors, including watering,

ramming, consolidating and dressing complete. Cum 10.00 2123.75 21,237.50

Structural steel work riveted, bolted or welded in built up sections,

10.2 trusses and framed work, including cutting, hoisting, fixing in position Kg 35672 133.7 47,69,346.40

5 and applying a priming coat of approved steel primer all complete.

Digitally signed by AMIT

Providing and fixing precoated galvanised iron profile sheets (size, shape

and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+

0.05 %) total coated thickness with zinc coating 120 grams per sqm as

per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both

side of the sheet and polyester top coat 15-18 microns. Sheet should

have protective guard film of 25 microns minimum to avoid scratches

during transportation and should be supplied in single length upto 12

metre or as desired by Engineer-in-charge. The sheet shall be fixed using

self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal,

complete upto any pitch in horizontal/ vertical or curved surfaces,

excluding the cost of purlins, rafters and trusses and including cutting to

6 size and shape wherever required.

Providing and fixing precoated galvanised steel sheet roofing

accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120

7 12.51 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy

primer on both side of the sheet and polyester top coat 15-18 microns

using self drilling/ self tapping screws complete :

7 12.51.6 Gutter (600 mm over all girth) Metre 60.00 1313.70 78,822.00

Providing and applying two coats of fire retardant paint on cleaned

wood / ply surface @ 3.5 sqm per litre per coat including preparation of

base surface as per recommendations of manufacturer to make the

8 surface fire retardant.

excluding the cost of centering and shuttering - All work up to plinth

1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources :

4.1.3 4 graded stone aggregate 20 mm nominal size derived from natural 7 7,878.50 55,149.50

9 sources) cum

Digitally signed by AMIT

5.33 Providing and laying in position ready mixed or site batched design mix

cement concrete for reinforced cement concrete work; using coarse

aggregate and fine aggregate derived from natural sources, Portland

Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in

recommended proportions as per IS: 9103 to accelerate / retard setting

of concrete, to improve durability and workability without impairing

strength; including pumping of concrete to site of laying, curing, carriage

for all leads; but excluding the cost of centering, shuttering, finishing

and reinforcement as per direction of the engineer-in-charge, for the

following grades of concrete.: Note: Extra cement up to 10% of the

minimum specified cement content in design mix shall be payable

separately. In case the cement content in design mix is more than 110%

of the specified minimum cement content, the contractor shall have

10 discretion to either re-design the mix or bear the cost of extra cement.

10 5.33.1 All works upto plinth level

10.1.1 5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 25.00 9504.75 2,37,618.75

10 5.33.2 All works above plinth level upto floor V level

10.2.1 5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 4.00 9860.4 39,441.60

5.22 Reinforcement for RCC work including straightening, cutting, bending,

11 placing in position and binding all complete upto plinth level.

11 5.22.6 Thermo-Mechanically Treated bars Kg 2755.00 107.85 2,97,126.75

Total for shade 55,82,617.10

Digitally signed by AMIT

Renovation of toilets and allied IE works and indoor lighting

Sl. No. DSR ref. Description Unit QTY Unit Rate Amount

Providing and fixing floor mounted, white vitreous

china single piece, double traps syphonic water

closet of approved brand/make, shape, size and

pattern including integrated white vitreous china cistern

1 17.81 of capacity 10 litre with dual flushing system, including each 4 18212.9 72,851.60

all fittings and fixtures with seat cover, cistern fittings,

nuts, bolts and gasket etc including making connection

with the existing P/S trap, complete in all

respect as per directions of Engineer-in-Charge.

Supply, Installation, Testing and Commisiong of each 4.00 7381.00

PNEUMATIC SINGLE PIECE SLIM CONCEALED

CISTERN BODY WITH INSTALLATION KIT & “S-TYPE”

DRAIN PIPE CONNECTION SET FOR WALL HUNG WC

(WITHOUT FLUSH CONTROL PLATE) Model

No. APCWHT- 5012500S or equivalent

17.7A Providing and fixing wash basin with C.I. brackets, 15 mm

dia CP Brass single hole basin mixer of approved

3 quality and make, including painting of fittings and

brackets, cutting and making

good the walls wherever required:

A White Vitreous China Wash basin size 550x400 mm each 50 3960.55

3.1 with a 15mm CP Brass single hole basin mixer 1,98,027.50

Providing and fixing white vitreous china flat back or wall

corner type lipped front urinal basin of

430x260x350 mm and 340x410x265 mm sizes

respectively with automatic flushing cistern with

4 17.4.1 standard flush pipe and C.P. brass spreaders with

brass unions and G.I clamps complete, including

painting of fittings and brackets, cutting and making

good the walls and

floors wherever required :

Digitally signed by AMIT

17.4 One urinal basin with 5 litre white P.V.C. automatic flushing each 28 6258.75

Providing and fixing water closet squatting pan (Indian type

W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre

low level white P.V.C. flushing cistern, including flush pipe,

5 17.1 with manually controlled device (handle lever) conforming

to IS : 7231, with all fittings and fixtures complete,

including cutting and making good the walls and floors

wherever required:

17.1.1 White Vitreous china Orissa pattern W.C. pan of size each 48 6767.4

580x440 mm with integral type foot rests

MR Supply, Installation, Testing and Commisiong of HAND each 4 2375.00

SHOWER (HEALTH FAUCET) WITH 8mm DIA 1.2 METER

LONG FLEXIBLE TUBE AND WALL HOOK ALD-CHR-573 or

Providing and fixing C.P. brass angle valve for basin mixer

7 18.53 and gyser points of approved quality conforming to IS :

Providing and fixing C.P. brass long body bib cock of approved each 100.00 777.38

8 18.51.1 quality conforming to IS standards and weighing not less than 690 77,738.00

gms. 15 mm nominal bore

9 17.70 Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Bottle trap 38 mm single piece moulded with height of 270

mm, effective length of tail pipe 260 mm from the centre of

the waste coupling, 77 mm breadth with 25 mm minimum

water seal, weighing not less than 263 gms

18.58 Providing and fixing PTMT grating of approved quality and

11.1 18.58.1 Circular type

11.1.1 18.58.1.1 125 mm nominal dia with 25 mm waste hole each 0 51.85

17.32 Providing and fixing mirror of superior glass (of approved quality)

12 and of required shape and size with plastic moulded frame of

approved make and shade with 6 mm thick hard board backing :

12.1 17.32.4 Rectangular shape 1500x450 mm nos 50 2093 1,04,650.00

Digitally signed by AMIT

Providing and fixing PTMT Waste Coupling for wash basin

and sink, of approved quality and colour.

17.69.2 Waste coupling 38 mm dia of 83 mm length and 77 mm each 76 122.4

breadth, weighing not less than 60 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC)

pipes, havingthermal stability for hot & cold water supply

and all CPVC plain & brass threaded fittings, including fixing

14 18.7 the pipe with clamps at 1.00 m spacing. This includes

jointing of pipes & fittings with one step CPVC solvent

cement and testing of joints complete as per direction of

Engineer in Charge

14.1 18.7.3 25 mm nominal dia Pipes metre 1500 401.55 6,02,325.00

14.2 18.7.4 32 mm nominal dia Pipes metre 900 518.75 4,66,875.00

14.3 18.7.6 50 mm nominal dia Pipes metre 200 934.15 1,86,830.00

MR Providing and fixing unplasticised PVC connection pipe of 60 each 50 170

15 cm length 8,500.00

18.17 Providing and fixing gun metal gate valve with C.I. wheel of

approved quality (screwed end) :

22.3 Providing and laying water proofing treatment to vertical and sqm 317 769.60

horizontal surfaces of depressed portions of W.C., kitchen and the

like consisting of: (i) Ist course of applying cement slurry @ 4.4

kg/sqm mixed with water proofing compound conforming to IS :

2645 in recommended proportions including rounding off junction of

vertical and horizontal surface. (ii) IInd course of 20 mm cement

plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing

compound in recommended proportion including rounding off

junction of vertical and horizontal surface. (iii) IIIrd course of

applying blown or residual bitumen applied hot at 1.7 kg. per sqm of

area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at

joints of PVC sheet should be 100 mm wide and pasted to each

other with bitumen @ 1.7 kg/sqm).

Digitally signed by AMIT

Filling available excavated earth (excluding rock) in trenches, plinth,

sides of foundations etc. in layers not exceeding 20cm in depth,

18 2.25 consolidating each deposited layer by ramming and watering, lead cum 10 196.00 1,960.00

up to 50 and for all lift

Excavating, supplying, stacking and filling of local earth (including

royalty) by mechanical transport upto a lead of 5km also including

19 2.25(a) ramming and watering of the earth in layers not exceeding 20 cm in cum 50 700.50 35,025.00

foundation trenches, plinth, sides of foundation etc. complete for all

Supplying and filling in plinth with sand under floors, including

20 2.27 watering, ramming, consolidating and dressing complete. cum 10 2123.75 21,237.50

Providing and fixing Ist quality ceramic glazed wall tiles conforming

to IS: 15622 (thickness to be specified by the manufacturer), of

approved make, in all colours, shades except burgundy, bottle

green, black of any size as approved by Engineer-in-Charge, in

21 8.31 skirting, risers of steps and dados, over 12 mm thick bed of cement sqm 2964.00 1267.95 37,58,203.80

mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement

slurry @ 3.3kg per sqm, including pointing in white cement mixed

with pigment of matching shade complete.

Providing and laying vitrified floor tiles in different sizes (thickness to

be specified by the manufacturer) with water absorption less than

0.08% and conforming to IS: 15622, of approved make, in all

22 11.41 colours and shades, laid on 20 mm thick cement mortar 1:4 (1

cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/

sqm including grouting the joints with white cement and matching

pigments etc., complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water

pipes conforming to IS : 13592 Type A, including jointing with seal

ring conforming to IS : 5382, leaving 10 mm gap for thermal

expansion, (i) Single socketed pipes.

Providing and fixing on wall face unplasticised - PVC moulded

fittings/ accessories for unplasticised Rigid PVC rain water pipes

conforming to IS : 13592 Type A, including jointing with seal ring

conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Digitally signed by AMIT

24.1 12.42.1 Coupler

24.3 12.42.2 Single pushfit Coupler

24.5 12.42.3 Single tee with door

24.7 12.42.4 Single tee without door

24.11 12.42.6 Shoe (Plain)

Dismantling tile work in floors and roofs laid in cement mortar

including stacking material within 50 metres lead.

25.1 15.23.1 For thickness of tiles 10 mm to 25 mm sqm 3307.05 73.40 2,42,737.24

Dismantling C.I. or asbestos rain water pipe with fittings and clamps

including stacking the material within 50 metres lead :

26.1 15.42.1 75 to 80 mm dia pipe metre 75.70

Disposal of building rubbish / malba / similar unserviceable,

dismantled or waste materials by mechanical means, including

27 15.6 loading, transporting, unloading to approved municipal dumping cum 100 263.95 26,395.00

ground or as approved by Engineer-in-charge, beyond 50 m initial

lead, for all leads including all lifts involved.

Total sanitary and tiles 73,50,215.26

Digitally signed by AMIT

LED Down lighter (SMD Type) (System lumen efficacy ≥ 105 < 120

lm/Watt ) Supplying, Installation, Testing & Commissioning of LED

Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD

type of following body material with PMMA and prismatic diffuser

and construction as per IS : 10322 with driver as per the

requirement with Driver efficiency >85%, Operating voltage AC 140-

270 Volt, frequency 50/60 hz, Operating temp range -50C to 400C,

28 8.1 internal surge protection of 2.5 KV with Short & Open circuit

protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified

Glare Rating) < 19, Flicker free (flicker should be below 5%), life

time (LED, Driver & electrical circuitry), of minimum 50000 Burning

Hours with 70% of initial Lumen maintained till life ends, CCT

3000°K /4000°K / 5700°K / 6500°K (As per ANSI Bin), SDCM

(Standard Deviation Colour Matching)

LED Panel light 2x2 ft. (System lumen efficacy ≥105 85%, Operating

voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range

-5 0C to 40 0C, internal surge protection of 2.5 KV with Short &

Open circuit protection, THD < 10% , P. F.≥0.95, IP20, CRI >80,

UGR (Unified Glare Rating) < 19, Flicker free, (flicker should be

29 8.6 below 5 %), life time (LED, Driver & electrical circuitry), of minimum

50000 Burning Hours with, 70% of initial Lumen maintained till life

ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K /

4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard

Deviation Colour Matching) 1.20 mm)

Wiring for circuit/ submain wiring along with earth wire with the

30 following sizes of FRLS/HFFR PVC insulated copper conductor,

1.7 single core cable in surface/ recessed steel conduit as required.

Supplying and fixing of following sizes of medium class PVC conduit

31 along with accessories in surface/recess including cutting the wall

1.21 and making good the same in case of recessed conduit as required.

Total Electrical 14,97,920.00

Digitally signed by AMIT