REPAIR MAINTENANCE OF MES SUB STN SECURITY LIGHT SIGNBOARD, SUB STN PUMP HOUSE BLDGS AND CERTAIN B R WORK AT SEWAR FORT KLP MALLAH PUP HOUSE AREA AT BHARATPUR

Amount

M&L for 15 mm thick rendering in cement mortar 1:4 on fair face of brick-work surface finished even & fair complete all as specified.

All as above item no 1 but on other than fair faces of brick work surface with cement mortar 1:6 finished even and fair complete all as specified.

M&L for Rendering 5 mm thick in cement and sand mortar 1:3 on fair faces of cement concrete surfaces of ceiling of chajjas / roof protection etc including finishing the surface even and smooth without using extra cement complete all as specified.

Taking down cement plaster or cement lime plaster on PCC/stone surface/brick surfaces including raking out joints hacking for key scrubbing down with water etc complete all as specified.

M & L for Preparation of new plastered surface of wall including cornices, pilasters etc by brooming down and applying two coats of distemper oil emulsion white or tinted over & including a coat of alkali resistant priming paint wall primer with hand roller & 3 mm wall care putty complete all as specified.

M&L for Preparation of newly plastered surfaces of Wall & applying three coats of white wash complete all as specified.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash complete all as specified.

M&L for Two coats of Weather Proof Exterior emulsion (Water Based 100% Acrylic ) paint using hand roller over & including one coat exterior grade wall primer on cement plaster,concrete ,exterior ceiling etc complete all as specified. Note:-Color & Pattern /Color Combination of the paint shall got approved from GE.

Demolition of brick masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stone work and precast concrete articles complete all as specified.

M&L Brick work with sub class 'B' old size bricks bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar 1:6 complete all as specified.

All as Item No 10 but except bricks complete all as specified.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15 CM thickness (below or above GL) complete all as specified.

M&L for 25mm thick Cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in Sub base complete all as specified.

M&L for chequered cement concrete tiles with gray cement and with pigment 20 cmx 20 cmx25mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, over 15 mm thick cement screed bedding layer in cem,ent mortar 1:6, complete all as specified.

M&L for Machine pressed precast concrete interlocking paver block with grey cement & pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade over and including 25mm thick fine sand cushioning complete all as specified.

Dismantling of Existing kerb stone of any size and shape including excavation around base, removing and stacking serviceable material 50m lead and disposal of u/s material within 50m lead complete all as specified.

Providing and laying factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified.

M&L dismantling floor,hearth or wall tiling including cement mortar bedding (but not backing) , removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L for Coloured Non skid ceramic tiles 7 to 8 mm thick in floor (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, set and jointed in neat cement slurry and pointed in coloured cement over & including 15mm thick screed bed in CM 1:4 complete all as specified.

M&L colored Glazed ceramic Tiles,in verticle surface 450X300X7mm set & jointed in neat cement sluury and pointed in white or colour cement to match the existing surface over and including 10mm thick rendering in CM 1:4 complete all as specified.

Dismantling posts or struts (wood, steel or R.C.C.) embedded in natural ground any section, including taking out embedded portion and making good disturbed ground complete all as specified.

Dismantling fencing wire mesh, any type complete all as specified.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil complete all as specified.

M&L Cement concrete 1:3:6 Type C-2 (using 40 mm graded stone aggregates ) in foundations filling and mass concrete complete all as specified.

S&F MS work as in angle iron fencing post, fixed independently for fixing chain link fence, including all necessary cutting, drilling holes, bolting etc for screwing chain link fencing complete all as specified.

Supply only Chain link MS galvanisd fencing, any size or type fixed to angle iron fencing post or angle frame complete all as specified.

Fixing only chain link fencing including line wires, any mesh size and type of standards rails straining bars etc incl provision of binding wire complete all as specified.

S&F of Mild steel screw bolts (machine made) with hexagonal or square head at one head and rounded the other or screwed both end each screwed end to be fitted with washers and one hexagonal or square nut exc 05 cm nexc 10 cm long dia of shank 05 to 10 mm complete all as specified.

M&L for preparation of new or previously untreated steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Dismantling corrugated or semi corrugated Asbestos cement sheets in roof coverings complete all as specified.

Dismantling of wrought iron or mild steel work of any description & fixed in any position complete all as specified.

S&F Rolled sections as in as in post ,roof trusses (framed), trussed, purlins, crane gantries, rails , fastenings , heavy bracket framing (Beam, tee, angle, channel or flat sections,ms pipe) including distance pieces, cleats etc. conforming to Fe-410W Gde E-250 quality 'A' including cutting,welding etc complete all as specified.

M & L for Pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

Dismantling of stone slab and tiles of any description or thickness in floors, etc. laid dry or laid dry and pointed complete all as specified.

M&L for Machine cut kota stone slab flooring 18-20 mm thick over cement screed 20 mm thick in cement mortar 1:6, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including necessary grinding ,rubbing to exposed edges and polishing complete all as specified.

M&L for Machine cut kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed 15 mm thick in cement mortar 1:4, laid and jointed with gray cement slurry mixed with pigment to match the shade of the slab including necessary grinding ,rubbing to exposed edges and polishing complete all as specified.

S&F of three layred 1000 ltr ISI marked rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including 20mm brass ball valve Including dismantling of existing water tank of 1000 Ltr capacity complete all as specified in SSR Part-I

Excavation in trenches not exceeding 1.5 m wide and not exe 1.5 M in depth and getting out in Soft Loose soil complete all as specified.

Returning filling in including spreading leveling, watering and well ramming in layers not exc. 25 cm each layer complete all as specified.

Removing excavated material to a distance not exe 50 M and depositing where directed not exceeding 1.50 M above the starting point complete all as specified.

Supply spreading in trenches fine dry river sand for cable protection and punning down gently by hand complete all as specified. (Note:- Punned thickness shall be measured)

M&L for brick protection with sub Class`B` bricks old size laid dry, flat over cable perpendicular across the cable in trenches complete all as specified.

S & F in replacement street light GI bracket of 1.2 mtr long made out of 40mm dia light grade GI pipe bend to shape of 120 degree end welded at required including 02 Nos MS clamp of flat iron 40 x 6mm with nuts bolts & washers for fixing on wall including necessary fixing arrangements on pole incl taking out old U/S bracket complete all as specified.

S&F in repairs for PVC copper cable 2.5 sqmm 3 core copper conductor 1100 Volt grade multi core multi stranded PVC insulated unsheated drawn through and including PVC conduit and accessories fixing on poles/ wall with clamps, nuts bolts etc from FRP box to street light fiting complete all as specified.

M&L for boring of holes under road, pavement, hard standing by trenchless technology using suitable tools and machinery for laying of pipe upto 150mm bore complete complete all as specified. Note :- GI pipe shall be measured and paid in separately

Supply and laying DWP HDPE pipes of pressure rating PN-10 of size 100 mm for the protection of the cable passing through road crossing etc complete all as specified.

Supply and laying DWP HDPE pipes of pressure rating PN-10 of size 50 mm for the protection of the cable passing through road crossing etc complete all as specified.

Taking out old un-servicable/ faulty PVC armoured LT under ground cable of any size any core complete all as specified.

S&F or laying ross linked poly-ethylene (XLPE) insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables ( heavy duty) with aluminium conductor, 1100 volts grade of cross-sectional area 16 Sqmm X 4 core laid in trenches/through pipe in road crossings/ paths /drains /ducts /floors /along poles/walls/ceilings/ equipments etc including commissioning and testing complete all as specified. (Note: :- (i) Necessary excavation and earth work, brick protection, sand cushioning and cover and GI pipe shall be measured and paid for separately.)

All as item No. 50.00 but size 25 sqmm X 3.5 core complete all as specified.

All as item No. 50.00 but size 50.00 sqmm 3.5 core complete all as specified.

Alll as item No. 50.00 but size 95 sqmm 3.5 core complete all as specified.

All as item No. 50.00 but size 120 Sqmm 3.5 Core complete all as specified.

All as item No. 50.00 but size 150 Sqmm 3.5 Core complete all as specified.

All as item No. 50.00 but size 185 sqmm 3.5 core complete all as specified.

All as item No. 50.00 but size 240 sqmm 3.5 core complete all as specified.

Supply, laying, testing & commissioning LT XLPE PVC insulated heavy duty electric cable of single core 120 Sqmm with stranded copper conductor 1100 volts grade (ISI marked) in trenches/pipes or fixed on pole complete all as specified.

Dismantling and taking down non functional/ unserviceable street /security light fittings of any type existing complete all as specified.

Supply, install, test and commissioning in replacement factory made THERMOPLASTIC/HDPE CABLE JUNCTION BOXES IP 66/67 “weather proof”, with terminals for outdoor installation (with knockouts for cable entry) of size 205 x 255 x 112 mm depth with cable entry size of 10-25 sqmm with terminal incl Aluminium bus bar of 63amp-04 Nos and MCB SP 6amp-01 No complete all as specified.

Supply & fix in replacement 60 watts LED street light fitings new generation energy saving ,environmental friendly ,long life,versatile pressure die cast aluminium with following specification IP66 with 10KV surge protection , PF>0.95, THD < 10%, input voltage 220-240V AC, operating voltage (VAC) 100V -300 V, Lum Flux (+-) 10% , CRI -80 Lum efficienacy (+-) 10% CCT -5700K road way,luminaire with high power LED as light source with warranty option of 5 years and suitable drivers etc and connecting with 3 x 1 sq mm multistranded PVC insulated copper conductor with PVC Conduit 20mm dia from fittings to the jucntion box and fixing to complete all as specified. Make: Cromption/Havells/Bajaj.

All as item No 62.00 but 70 watt LED fittings complete all as specified.

Supply and fixing highly efficient high power multi LED flood fitting 200 watts with pressure die cast aluminium housing reflector and enclosed with toughened glass IP66 complete prewired and connecting with 1.0 sqmm 3 core flexible wire including fixing arrangement on wall etc complete including dismantling of existing unserviceable flood light fittings complete all as specified.

Supply and fixing highly efficient high power multi LED flood fitting 100 watts with pressure die cast aluminium housing reflector and enclosed with toughened glass IP66 complete prewired and connecting with 0.5 sqmm 3 core flexible wire including fixing arrangement on wall etc complete including dismantling of existing unserviceable flood light fittings complete all as specified.

supply and fixing 1X9 Watt square shaped integral decorative LED (warm white) Bollard polycarbonate diffuser and IP 65 protection and mounting fitting with PCC foundation complete all as specified & directed by Engr-in-charge.

S & F in replacement 4 sqmm solid conductor 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed twin core cable flat or circular from junction box to fitting complete all as specified.

S&F in replacement MCCB 04 pole 63 Amp, Thermal magnetic, adjustable type, breaking capacity not less than 16 KA,415 volts complete all as specified.

S&F in replacement MCCB 04 pole 100 Amp, Thermal magnetic, adjustable type, breaking capacity not less than 25KA,415 volts complete all as specified.

Supply and fix MCCB 4 pole,250 Amp 415 Volt adjustable type with breaking capacity 36 KA from panel boards etc complete all as specified.

Supply in repair MCCB 800 Amp,4 Pole, breaking capacity 35/50 KA, 415 V - 50 Hz, fixed in existing panel & connecting complete all as specified.

Supply in repair MCCB 400 Amp,4 Pole, breaking capacity 35/50 KA, 415 V - 50 Hz, fixed in existing panel & connecting complete all as specified.

Supply and spread 40mm-80 mm stone aggregate in layers inside the substation switching yard including leveling,ramming complete all as specified.

Supply and fixing, install, test and commissioning of LT busbar Feeder pillar box outdoor type totally enclosed with front and rear opening hinged doors with canopy sloped top projected and raised platform of suitable sizes weather dust vermin proof made out of 3.15 mm thick CRCA sheet, factory made powder coated as approved colour, Copper bus bar suitable for 3 phase 4 wire LT, AC, 50Hz, 433 volts, 400 Amps rating capacity RYBN insulated with sleeved insulation complete, PCC platform made out of 1:2:4 type B1 and pedestal of 45 cm height from GL with suitable nut, bolts, washers etc., all as specified and directed for suitable to accomodate the following items including supply and fix following items and all as specified and directed by dismantling exisiting unserviceable LT panel complete with LT panel made by CPRI approved manufacturer confiring to IS:-8623-1993. Note - The lay out drawing of the panel shall be got approved by the contractor from GE before panel fabrication and shall be fabricated from CPRI approved manufacture. [a] Incomer: MCCB 4 pole 320 Amps with breaking capacity 35KA adjustable type with extended terminals- 01 No's [b] Three phase 4 wire copper busbar 400 Amps rating capacity RYBN insulated with sleeved insulation complete. [c] Digital AMMETER WITH C.T -03 Nos [d] Digital volt Meter-01 [e] LED RYB indiacator lamps-01/Set

Supply and fixing, install, test and commissioning of LT Feeder pillar box outdoor type totally enclosed with front and rear opening hinged doors with canopy sloped top projected and raised platform of suitable sizes weather dust vermin proof IP-54 protection CPRI approved, factory fabricated, cubical panel free standing type, made out of 3.00 mm thick CRCA sheet with locking arragement , factory made powder coated as approved colour, copper bus bar suitable for 3 phase 4 wire LT, AC, 50Hz, 433 volts, 300 Amps rating capacity RYBN insulated with sleeved insulation complete with multifunctional meter LED type by showing Amps, volts, frequency etc along with suitable size of CT on outgoing, indicating lamp RYB , complete internal wiring with suitable size of PVC insulated copper conductor cable, including cable glands and lugs for incoming and out going cables as per required sizes, PCC platform made out of 1:2:4 type B1 and pedestal of 30 cm height from GL with suitable nut, bolts, washers etc., all as specified and directed for suitable to accomodate the following items including supply and fix following items and all as specified and directed by dismantling exisiting unserviceable LT panel complete.

Incoming: MCCB 4 pole 200 Amp with breaking capacity 35 KA adjustable type with exended terminals -01 Nos Outgoing [a] MCCB 4 pole 100 Amps with breaking capacity 25KA adjustable type with extended terminals- 02 No [b] MCCB 4 pole 63 Amps with breaking capacity 16 KA adjustable type with extended terminals- 02 No's [c] MCB TPN 40 Amps,breaking capacity 16 KA -02 Nos (d ) Current Transformers-03 Nos (e) Multi functional Meter-01 (f) LED RYB indiacator lamps-01/Set Note-: The panel must have separate Bus bar chamber, cable chamber and proper spacing must be maintained between each chamber of panel as per IS .

Supply and fixing, install, test and commissioning of LT Feeder pillar box outdoor type totally enclosed with front and rear opening hinged doors with canopy sloped top projected and raised platform of suitable sizes weather dust vermin proof IP-54 protection CPRI approved, factory fabricated, cubical panel free standing type, made out of 3.00 mm thick CRCA sheet with locking arragement , factory made powder coated as approved colour, copper bus bar suitable for 3 phase 4 wire LT, AC, 50Hz, 433 volts, 600 Amps rating capacity RYBN insulated with sleeved insulation complete with multifunctional meter LED type by showing Amps, volts, frequency etc along with suitable size of CT on outgoing, indicating lamp RYB , complete internal wiring with suitable size of PVC insulated copper conductor cable, including cable glands and lugs for incoming and out going cables as per required sizes, PCC platform made out of 1:2:4 type B1 and pedestal of 45 cm height from GL with suitable nut, bolts, washers etc., all as specified and directed for suitable to accomodate the following items including supply and fix following items and all as specified and directed by dismantling exisiting unserviceable LT panel complete.

Incoming: MCCB 4 pole 400 Amp with breaking capacity 35 KA adjustable type with exended terminals -01 Nos Outgoing [a] MCCB 4 pole 200 Amps with breaking capacity 25KA adjustable type with extended terminals- 01 No [b] MCCB 4 pole 160 Amps with breaking capacity 25 KA adjustable type with extended terminals- 01 No's [c] MCCB 4 pole 100 Amps with breaking capacity 16 KA adjustable type with extended terminals- 01 No's [d] MCCB 4 pole 63 Amps with breaking capacity 16 KA adjustable type with extended terminals- 05 No's [e] MCB TPN 40 Amps,breaking capacity 16 KA -02 Nos (f ) Current Transformers-03 Nos (g) Multi functional Meter-01 (h) LED RYB indiacator lamps-01/Set Note-: The panel must have separate Bus bar chamber, cable chamber and proper spacing must be maintained between each chamber of panel as per IS .

Supply and fixing in replacement of Lithium base Energy efficient integrated Solar street light of 30/32 watt in Aluminium Die casting body / FRP Bpdy , corrosion resistance,integrated PV panel Automatic dusk to input voltage 12.8V with suitable battery ,Driver efficiency .85%,PV module itself will be used to sense the ambient light to switch ON/OFF the Lamp, inbuilt MPPT charge controller, IP65,both PIR and fixed dimming available,4500 lumens (at full brightness) with grater than 150 lumen per watt,5700ANSI, cool white(5500K-6500K),CRI.70,moptical used, Metal core PCB,Low voltage cutoff ,high power LED,wide beam Angle(120 degree) LED Life 50000 hrs, weight less than 15 kg with GReen/Red indicator swith with suitable battery rating 12.8V-BIS standard of complete specified & directed.Make: Orient/HAVELLS/Crompton Protections: Short circuit, overload,Reserve polarity and battery protection.Firm should provide vital parametres Test report from NABL accredited lab and should be of made in India with CE & ROHS complaint.

M & L for double legged informatory sign board of size 1.00m x 1.50m fixed on single frame, both side and meeting back to back on the stainless steel 50x50x3.65mm square pipe. The board are of high intensity grade RETRO-REFLECTIVE SHEETINGOF AVERY DENNSION sheeting made out of 2mm thick alcoband sheet /aluminium composite pannel sheet conforming to IS-736,colour as approved by Engg-In-Charge and stainless steel square pipe of size 50x50x3.65mm with nut and bolt. The lettering will be computerised on board over verticle post 50mm stainless square pipe, 3.65 mm thick 3.20m long having 2 Nos flat iron strip of strip 40x5 mm, 0.30mm long on bottom and fixed with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) in post holes of size 0.45x0.45x0.75 M including dismentaling of old board complete all as specified.

M & L for double legged informatory sign board of size 5.00m x 4.50m fixed on single frame, both side and meeting back to back on the stainless steel 50x50x3.65mm square pipe. The board are of Acralic sheeting of avery dennison made out of 2mm thick acralic sheet , colour as approved by Engg-in-Charge and stainless steel square pipe of size 50x50x3.65mm with nut and bolt. The lettering will be computerised on board over verticle post 50mm stainless square pipe, 3.65 mm thick 3.20m long having 2 Nos flat iron strip of strip 40x5 mm, 0.30mm long on bottom and fixed with PCC 1:3:6 type C-1 (using 20mm graded stone aggregates) in post holes of size 0.45x0.45x0.75 M including dismentaling of old board complete all as specified.

M & L for Earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm buried directly in the ground vertically to depth not less than 2.25 Mtr below the ground level with the top edge of earth plate, depth not less than 1.5 Mtr below the ground level connected to GI earth strip of 32 mm x 6 mm size by means of bolts, nuts and washers protected by GI tubing light grade 40 mm dia uptoTest point 20 mm dia watering pipe with funel & wire mesh, PCC pit in PCC 1:2:4 using 20 mm stone aggregates chamber 40 mm thick RCC cover slab (1:2:4) type B-1 using 20 mm graded stone aggregates complete all as specified and shown in electrical plate No.3 of SSR Part-I including earth work in any type of soil ,removal of surplus soil and providing charcol dust & salt layers all around the earth plate upto 15 cm all as required specified & directed by engr in charge. ( For LT panel and Transformer) (Note:- Up to 7.5 Mtr length of pipe of 40 mm dia and GI strip shall be deemed to be included in unit rate quoted by tenderer GI pipe and GI strip beyond 7.5M will be measured separately under respective item.

M & L for bore well Earthing complete with the help of machnical boaring machine of 150mm dia 30 mtr depth, supply and fix 150mm bore ,UPVC pipe 6 kg/sqcm rating,06 mtr long with the help of suitable size clamp with nut bolts and washer -01 no including charcoal dust, salt fill in bore well for achieve earth conductivity less than 1 ohm. M&L for covering of bore well mouth with PCC (1:2:4) type B1/Brick masonry pit of size 45X45X45 cm complete and give the minimum earth test result below 1 ohm complete all as specified and directed by Engineer-In-charge . ( Note:- (i) The earth pit shall be refilled by boulders free from vegitable soil. (ii) Earthing shall be tested by contractor in presence of Engr-In-Charge record shall be maintained.payment shall be admissible only after satisfactory test results.GI Pipe electrode and GI strip shall be measured & paid separately.

supply & lowering of GI tubing 50 mm dia medium grade incl necessary fittings for lowering in borewell of depth up to 30 mtr and providing necessary holes in pipe to achieve good earth conductivity complete al as specified.

S&F GI strip 32X6 fixed on wall or buried in ground and connected to the earth plate or any other indicated situation complete al as specified.

M & L for chemical Earthing complete with Copper plate 600 x 600 x 3.mm buried directly in the ground vertically to depth not less than 2.25 Mtr below the ground level with the top edge of earth plate, depth not less than 1.5 Mtr below the ground level connected to copper strip of 25 mm x 3 mm size by means of bolts, nuts and washers , returning & filling the pit with excavated soil mixing with charcoal 250 KG ,crystal salt 200 KG , magnesium sulphate of 100 KG and vegitable soil all around the plate up to 350 mm above from top edge of plate and balance portion filling with excavated soil in layers not exceeding 25 CM thick, 25 mm galvanized iron medium grade watering pipe up to top of plate ,50 mm bore galvanized iron light grade pipe for earth strip protection , including all excavation earth work in any type of soil ,PCC 1:3:6 type C1 for chamber of internal size 300 mm X300X300mm with 120 mm thick wall and 700 mmX700mmX150 mm thick ,bed concreate,RCC 1:2:4,type B1 for precast chamber cover 50 mm thick ,reinforced with welded steel wire fabric of XPM jali (weight not less than 4.00 Kg/sqm),funnel,with wire mesh complete al as specified. Note:- Up to 7.5 Mtr length of pipe of 40 mm dia and copper strip shall be deemed to be included in unit rate quoted by tenderer.)

Supply and fixing in repairs LED post top lanterns fitting made in cast aluminium spigot housing with decorative clear acrylic diffuser and IP66 protection upto 20 watt ,warm white complete al as specified.

Supply and fixing in repairs LED garden lights fitting made in cast aluminium spigot housing with decorative clear acrylic diffuser and IP66 protection upto 20 watt ,warm white complete al as specified.

M&L for preparation of old painted surfaces of Steel Tubular pole 7/9 mtr long by scarping old paint and applying two coats of Aluminium paint including numbering of pole with black oil paint and painting the base of the pole in alternate black and yellow stripes each 30 Cm apart up to 1.5 mtr height including marking of MES No. with black paint on the pole all complete al as specified.

M&L for straight through joint (epoxy) suitable for 3 ½ / 4 core up to 95 Sqmm size underground cable complete al as specified.

M&L for straight through joint (epoxy) suitable for 3 ½ /4 core 95 to 240 Sqmm size underground cable complete al as specified.

M&L for finding faults of LT UG cable XLPE of any size and any length by using computerised / primary current injection method / any other method as directed by the GE and locating fault, cutting and removing the faulty portion of the cable and jointing with suitable cable joint and testing after jointing all as required complete al as specified.

Materials and labour for servicing & spray painting factory made powder coated as approved colour and servicing of LT panel with burnts wiring, cleaning of panel , lugs, glands of any size, and others connected accessories complete al as specified.

Material and labour for street/security pole numbering complete al as specified.

S & F cable route indicator made out of 50x50x6mm angle iron, 150mm long embedded in PCC block of suitable size with the letter 'LT CABLE' suitable inscribed on CI circular plate plate 8mm thick, 100mm dia complete al as specified.

M&L for disconnection of LT panel incl LT cables of size upto 240Sqmm X 3.5/4core from existing foundation and reconnection with same panel after taking necessary corrective action to lift the panel height incl excavation and taking down existing cable with loop, providing new AL lugs and cable gland of appropriate size,insulation tape etc to restore electric supply incl necessary iron work to modify height of existing LT panel upto 1.2 Mtrs above existing level incl necessary welding work,nuts & bolts and 2 coat of paint with existing color over one coat of primer and required including necessary PCC work complete al as specified.

M/s Ranaji Construction Co (BID ID -3487753)

PD GUPTA AND COMPANY (BID ID -3481846)

shyam construction (BID ID -3487774)

krishna Associate (BID ID -3487616)