PROVN OF COVER SHED AT TARANG BAR AT RS COLABA UNDER GE NW NAVY NAGAR COLABA MUMBAI

Amount

M&L for Cement concrete type E-2 1:5:10 ( 40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L machine cut Kota stone ( greenish colour, pre mirror polished) flooring 20-25mm thick over over 20 mm thick screed bed in cement mortar 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified.

Excavating in post holes each n exc 0.5cu. m, getting out in soft/ loose soil, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc. 25 cm, watering and removing surplus soil to a distance n.exc. 50m and making good surface all as specified and as directed by Engineer-in-charge.

M & L for PCC 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in foundation of post holes for embeddigng post /struts complete all as specified and as directed by engineer-in-Charge.

M & L mild steel rolled sections as in main and cross beams, tubular posts, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates and similar work confirming to Fe.290.Gde-E-165 complete all as specified and as directed by engineer-in-Charge.

M&L for preparation of new steel surfaces of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and as directed.

M & L for Roughening surfaces of old concrete floor by picking, sweeping cleaning and washing down with water to remove dust, etc. and Brushing neat cement slurry with 3.0kg of cement per sqm complete all as specified and directed

M&L for Vitrified Ceramic tiles light shade 10 mm thick (square /rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed or beddingin cement mortar 1:4 etc complete all as directed .

M&L brick work with sub class 'B' old size bricks, straight or curved on plan exc 6m mean radius built in CM 1:4

M&L rendering 15 mm thick in cement mortar (1:4) on bricks or concrete surface finished fair and even complete all as specified and as directed

M & L Preparation of new plastered surfaces of walls, pillars, cornices & applying two coats of Acrylic emulsion paint exterior grade (100% Acrylic) over one coat of primer including necessary scaffolding, Safety net etc all complete as directed by Engr-in-Charge.

Taking down cement plaster, any description on brick or stone walls, etc including racking out joints hacking for key scrubbing down with water etc.

M&L for Rendering 10mm thick in CM 1:4 backing coat to tiles/stone all complete as directed by Engr-in-Charge..

M&L for digital matt finish joint free coloured ceramic tiles size 300mmx600mm 10 mm thick set and jointed in neat cement and pointed in white or coloured cement to match the shade on vertical surface complete all as specified and directed.

S&F anodised aluminium snap grid frame work (Grid section bevelled tagular XL15mm silhouette) for false ceiling size of grid 605 x 605 mm including 6 mm dia GI hanger adjusting level fixed to slab/purlins by means of ceiling cleats made out of GI flat 40 x 3 mm & 600 x 600 x 16 mm size dune finished bevelled tegular board H3651B complete all as specified.

M&L Granite (of any type) 20mm thick machine cut, as in steps, windows cills, cooking platform, and other similar situations bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing and rounding to edges complete over 20mm thick screed bed or beddingin cement mortar 1:4 etc complete all as directed .

M & L 20mm thick Granite (of any type) machine cut, in skirting/dado, window sides and lintel laid over 10mm thick backing coat in CM 1:4 and jointed with grey cement slurry, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding, polishing and rounding to edges complete

M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed.

M&L RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in beams/lintels

M & L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc.

M/L for 10mm dia and over TMT bars cut to length, bent to shape required etc incl cranking, bending spirally for hooping for columns, hooking ends and binding with MS wire (annealed) of dia not less than 0.9 mm or securing with clips.

Ditto but 5mm dia and over upto incl 10 mm dia in stirrups, spacers, binders.

S&F Anodised aluminium power coated of any colour (minimum thickness of powder coating 50 micron) frame & shutter for doors,windows,ventilators,side hunge/sliding one or more rebates including necessary jointing cleats,glazing clips, rubber neoprene packing, anodised aluminium snap beading screw Tee etc section complete all as specified and directed

S&F 4 mm thick sheet glass ordinary quality coloured exc .5 sqm each with film complete all as specified and directed

S & F aluminium alloy wire mesh 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

S & F 12 mm thick transperent tinted glass fixed to door/windows frames complete with film rubber beading grinding /chamfered to glass corner all as specified and directed by EIC.

S&F 300 mm long aluminium alloy , anodised sliding door bolt with hasp and staple ( bolt type ) and fixing bolt and sliding bolts of extruded section or cast aluminium alloy.

S&F 150 mm extruded aluminium handles, fabricated type anodised

S&F 150mm aluminium anodised barrel tower bolts of extruded section

S&F floor door stpper 150 mm size aluminium alloy body and tongue, anodised with hard drawn steel spring

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed

S&F 100 mm size mild steel mortice 4 lever lock vertical type

M & L Complete removal of existing treatment, preparing surfaces, plastered or unplastered old surfaces priming plastered and other surfaces with alkali-resistant priming paint and applying two coats of distemper oil emulsion, white or tinted on walls incl 3mm thick wall care putty on wall all as specified.

M & L Complete removal of existing treatment from old wall & ceiling surfaces by scrapping, washing & applying two coats of Acrylic emulsion paint exterior grade (100% Acrylic) over one coat of primer including necessary scaffolding, Safety net etc all complete as directed by Engr-in-Charge.

M & L Preparation of old painted steel surfacs of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F Stainless Steel curtain rod 25mm dia fixed to brackets complete all as specified and directed

S&F stainless steel fancy type domes and bracket fixed to both ends of 25mm dia curtain rod complete all as specified and directed

S&F Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/clading to wall, fixed with self tapping screws as specified.

Excavation in trenches in hard / dense soil, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc 10 sq m on plan and n. exc 1.5 m in depth and getting out all as specified.

Demolition and breaking up drain pipes 150 mm internal dia( salt glazed ware, AC or reinforced concrete set in cement mortar complete all as specified and directed .

M & L for Reinforced Concrete pipes, 150 mm dia confirming to class NP2, laid in trenches and jointed with collars as specified.

M & L Cement concrete bed to drain pipe and packing under haunching against side of pipes after laying in PCC (1:3:6) type C-2 using 40mm graded stone aggregate for 150mm dia pipe complete all as secified and directed

Returning , filling in, includding spreading , leveling , watering and well ramming in layers n. exc. 25cm in hard / dense soil all as specified.

Removing excavated soil and demolised material outside MoD land to a distance exc 5 Km but n. exc 10 Km all as specified .

S & F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls.

S & F PVC (SWR) bends 110mm bore any radius

S&F Mild steel sheet 1.25mm thick eaves gutters, galvanised class 3, half round with rounded edges of dia 150mm all as specified.

Material and labour for point wiring complete with proper colour coding using, 1100 volts grade, 1.5 Sqmm, PVC insulated FRLS, unsheathed wire with multi stranded copper conductor conforming to IS-694, part-II, ISI marked and including PVC casing and caping not less than 25 mm size, ISI mark with all accessories on wall/ceiling/floor/roof etc, including 1.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 volts multistranded copper conductor green colour as continuous earth wire connected to common earth dolly all as specified and directed for the following :- NOTE : Circuit conductor from MCB DB to Switch boards should not be less than 2.5sqmm.

One light/Ceiling fan point controlled by one switch.

One 3 pin switch socket combination 5 Amps on the same board with other switches.

One 3 pin switch socket combination 5 Amps, independent.

All as per item No 48.00 above but with 2.5 sqmm cable for one three pin 15 Amps socket out let controlled by one switch.

All as per item No 48.00 above but with 4.0 sqmm cable to connecion of AC plug and socket box enclouser. NOTE : Separate Circuit conductor from MCB DB to Plug socket box to be drawn for each points control by 25 Amp MCB and length of circuit as per site requirement and as directed.

S & F with modular switch, 1 module, single pole one way 6 Amp confirming to IS:3854 and ISI marked complete all as directed. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

S & F with modular switch, 1 module, single pole one way 16 Amp confirming to IS:3854 and ISI marked complete all as directed. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

S & F with modular socket 6A, 3 pin, 2 module confirming to IS:1293 : 2019 and ISI marked complete all as directed. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

S & F modular switch, 1 module, single pole one way 16 Amp confirming to IS:3854 and ISI marked complete all as directed. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

Supply and fix Plug and socket distribution box of CRCA sheet steel powder coated conforming to IS 8623-1 & 3, IEC 61439-1 & 3 for single phase, nuetral and earth of capacity 20 Amp, 240 V, 50Hz controlled by housed MCB SP 20 Amp, mounted/flushed on wall surfaces complete all as dierected. Make:L&T/Havells//Siemens/Schneider/ABB Note : MCBs shall be measured and paid separately under respective items.

S & F ceiling rose surface bakelite 65x50 mm with 3 terminals.

S & F modular PVC Gang box of 8 module, ISI marked for mounting of modular switches and sockets including blank plate for blank module. Make - Crabtree(Athena)/Anchor(Penta)/Legrand(Britzy)

All as per Item No- 57.00 above but of modular PVC Gang box, 3 module.

All as per Item No- 57.00 above but of modular PVC Gang box, 1/2 module.

S&F modular white cover plate with frame, 8 module.

S&F modular white cover plate with frame, 3 module.

S&F modular white cover plate with frame, 1/2 module.

Supply and fix LED batten fitting 20 Watt, 240V, 4ft warm white comprises of extruded channel in thermally conductive material with decorative end cap and high translucent serration milky white diffuser of high optically efficient plastic FR grade. The luminaire is pre-wired with high efficiency electronic driver having operating voltage 140-270V, P.F >0.95, THD <20% and IP20 protected alongwith provision of two Nos of PVC box of size 75x75x20mm for mounting light fittings including. The contractor shall provide test certificate from authorized lab. Make of Light Fitting : Wipro/Crompton/Philips/Bajaj/Polycab

Supply and fix decorative wall light fittings, gold finish fixture with cognac hammered glass diffuser suitable for 7.5/9 W LED filament lamp E27 base prewired with suitable size of flexible cord upto ceiling rose including 9 watt LED bulb. Make of LED strips : Havells Cat Part No LHFOAJD1TZ1A060 or equivalent model of Bajaj/Wipro/Crompton.

Supply and fix flexible LED strips with uniform light distribution and long lasting adhesive for perfect cove lighting solution flexion LED Strip 24 W BLUE in colour complete with all accessories. Make of Light Fitting : Havells Cat Part No LHEHCPPGNN1W024 or equivalent model of Bajaj/Wipro/Crompton.

Supply and fix for wall mounting fan 400 mm sweep 230 V 50 Hz providing air delivery 100 CMM, 2250 RPM and soft head tilting to adjust air flow direction alongwith all allied accessories complete all as specified and directed. Make - ORIENT Cat part No: Tornado Wall-50 or its equivalent in Havells/ Bajaj/Crompton.

M & L for snap-on trunking system with cover, angles, bends and all accessories and fitting of size 50x80 mm fixing on wall for fixing of submain cable inside the trunking Complete all as specified and directed . Make- Legrand Cat No-075601 or equivalent in Honeywell/Obo.

M&L for XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 volts grade, of size 25 sq mm 4.0 core laid on wall/floor or passing through cable trunking complete all as specified.

Taking out Old U/S and Supply and fixing of MCB TPN DB 4 way as per IEC 61439-3 Suitable for Flush /Surface mounting with 100 A Copper Busbar for phase with 2 Neutral bar, 2 Earthbar and Cable ties for Cable management fully insulated busbar & shrouded Neutral bars improved Pan assembly for ease of installation prefitted masking sheet reversible metalic door for IP 43 DB's for provision for 63/100 MCB TPN as incomer and SP/TP MCB's as outgoing complele all as specified and directed. Make : Legrand/Havells/Siemens/L&T

S & F miniature circuit breaker (MCB) TPN, 63 Amp, 415V, 10KA 'B' curve in the DB complete with connection testing and commissioning complete all as specified. Make : Legrand/Havells/Siemens/L&T

S & F miniature circuit breaker (MCB) SP, 5 to 32 Amp, 240V, 10KA 'B' curve in the DB complete with connection testing and commissioning complete all as specified. Make : Legrand/Havells/Siemens/L&T

M & L for earthing with galvanised steel earth plate electrode 600mm x 600mm x 6 mm burried directly in ground earth pit not less than 2.25 mtr deep below normal ground level with top edge of the plate vertically to a depth not less than 1.5 mtr below ground level connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 including GI pipe 15 mm dia light grade for protection to the extend of 7.5 mtr as earthing lead connecting to equipment with provn charcoal and salt complete including PCC chamber with RCC cover watering arrangement with GI pipe 20 mm dia medium grade and MS funnel, including excavation and earth work and returning, filling in including ramming and removal of surplus soil and testing on completion complete.

SATYANARAYAN CONSTRUCTION

Unitech Enterprises

Nilesh Construction

BOB ENTERPRISES

S S ENTERPRISES

Anil Industrial Corporation

SHREE JAGDISH FURNITURE CO.