WBPWD/SEHEC/SKHED/NIQ36/19-20

Amount

Dismantling the existing damaged wiring, small panels, DBs, fans, fittings other electrical accessories and stacking them properly as per direction of EIC.

Power cum control panel for Chiller :

SITC of floor mounted Indoor type extensible cubical MV switchboard, fabricated by CPRI approved panel maker having compartmentalized design, fabricated out of 14 SWG ( 2.0 mm ) nominal thickness CRCA sheet steel for framework and covers, and 3 mm nominal thickness for gland plates, including cleaning and finishing complete with 7 tank process, with short circuit withstand capacity of 31 MVA for one second, front and back openable, hinged, single shuttered, single door, with locking arrangement, good quality dust, damp and vermin proof rubber gaskets, solid connections from main busbars to switchgears with required size of Copper busbars, connections and interconnections and control wiring using 2.5 sq. mm of RYB colour coded FRLS PVC Insulated Copper conductor single core cables and copper cable lugs. CT Connection should be done through CT shorting terminals. There should be LED indicating lamp for showing R, Y, B, for both the incoming and On, OFF, TRIP on the panel door for MCCBs.

1 no. of 25 mm x 5 mm GI earth strip for earthing, cable alleys, cable gland plates in two halves, dinrail for mounting switchgear, metering arrangements, drilling holes, detachable gland plates / knockout plates, mounting on MS channel iron framework 75 mm x 40 mm x 5 mm for floor mounting of MV panel, providing MS plate, suitable for bottom cable entry, grouting in ground, powder coating, providing and fixing the following switchgear and measuring instruments, earthing, cartage from fabricator's premises to site of work etc. as required.

BUSBAR: S&F 600 Amp capacity 99.9% - 99.5% electrolytic grade tinned copper ( test Certificate should be produced by manufacturer) semi soft, tined electroplated with heat srinkable PVC sleeve 4 Bar Bus Bar of Proper Size mounted on non-hygroscopic porcelain insulator / hylam sheet having sufficient di-electric strength duly wrapped with colour PVC tapes (Red, yellow, blue & black) for phases & neutral identification & all connection made with required size cu bars -2 Set

MCCB: 415V (Uimp=12kV peak), Icu@415V=Ics for 1 sec = 50kA, 4P Communicable, MCCB with microprocessor based LSIGN release having numerically adjustable overload with time delay, short circuit with time delay, Instantaneous current, Earth fault with time delay, neutral protection - (min. 50%, 100%), & inbuilt current, Voltage, unbalance, power, Energy (min Class 2), MD with date & time stamp, power factor, %THD etc. measurement and display in above local display, test facility etc. Both side spreader link, extended rotary handle etc. There should be LED indicating lamp for showing On, OFF, TRIP indication on the panel door. There should be Electrical and mechanical interlock between two incomers. [ make : ABB/ Legrand/ L&T/Schneider/ Siemens] i) Incomer: 50KA 400A: 2 set.

SDFU: i) 415V 315A TPN SFU with 3 nos. 315A bolted type HRC Fuse. [ make : ABB / L&T/Schneider/ Siemens] ------------- 01set.

ii) 415V 63A TPN SFU with 3 nos. 63A HRC Fuse. [ make : ABB / L&T/Schneider/ Siemens] ------------- 02set.

iii) Star-Delta starter (MUG-15 type, L&T) inbuilt with single phasing protection, phase reversal protection & O/L protection relay including Ammeter & CTs (for three nos. Chilled Water pumps) --------------- 02set

Control panel for AHU :

S&F of wall mounted type control panel by fabrication of 2mm thick sheet steel box (600 mm x 600 mm x 250 mm depth) with powder coated paint and both side (top & bottom) gland plate and mounting brackets (4nos) for fixing on wall by S/F 10mm dia anchor fastners including providing internal electrical wiring by suitable size FRLS Cu wires (Make-RR Kabel/ Polycab/ Finolex) for power and control circuits between S/F following electrical accessories mounted on a single detouchable 2mm thick fabricated sheet duly painted and housed inside the sheet steel enclosure by 4 nos bolting arrangement and proper tagging/ferruling and marking of logic elements as per direction of EIC.

63A 4P MCB, (Make- L&T) - 1 no.

20A 4P MCB (Make- L&T) -- 3 nos.

20A DP MCB (Make- L&T) -- 1 no.

6A SP MCB (Make- L&T) -- 4 nos.

MNX-32 3P Contactor (Make- L&T) -- 4 nos.

Auxiliary Contactors 24V AC MNX0 (Make- L&T) -- 1 no.

Add on block 1NO+1NC (Make- L&T) -- 3 nos.

Add on block 2NO+2NC (Make- L&T) - 2 nos.

Thermal Over Load Relay, Range 9-15A (Make- L&T) - 1 no.

SPP + Phase Reversal + OV + NV Relay (Make- L&T, SM500 Cat no. MB53BM) - 1 no.

Toggle switch ON-OFF - 2 nos.

Control Transformer 230V/24V AC OUTPUT 6A-10A - 1 no.

Red push button with element - 1 no.

Green push button with element - 1 no.

LED indication lamp (R- 3nos, Y- 1 no, B- 1 no, G- 2 nos, Amber- 1 no.) - 8 nos.

Digital Voltmeter (Make- L&T) - 1 no.

Digital Ammeter (Make- L&T) - 1 no.

Current Transformer 60/5A, Make - Kappa - 3 nos.

100mm sweep exhaust fan with louver - 1 no.

L.T. Control switch 25A 3P C/O (Make- Siemens, 3LAO 202 -1YA ) - 1 no.

Clear Plastic display window size 100mm x 100mm to be fixed at front door for looking at VFD display screen - 1 no.

2.5 sqmm KUT terminal block with end supports (Make- Elmex) - 13 nos.

6 sqmm KUT terminal block with end supports (Make- Elmex) - 16 nos.

150A FP stud type power terminal (Make- Elmex) - 1 no.

Supply & Delivery of 1.1 KV Grade 4 Core 240 mm² XLPE Ar./ Al. Cable. [make: Finolex / Havells / Polycab]

Laying the above Cable in existing masonery trench as to GS.

on prefixed tray/ Bracket including S & F MS clamps if required as to GS.

Through U PVC / G.I. pipe as to GS.

Supply & Delivery of 1.1 KV Grade 4 Core 185 mm² XLPE Ar./ Al. Cable. [make: Finolex / Havells / Polycab]

on prefixed tray/ Bracket including S & F MS clamps if required as to GS.

Through U PVC / G.I. pipe as to GS.

Supply & Delivery of 1.1 KV Grade 4 Core 70 mm² XLPE Ar./ Al. Cable. [make: Finolex / Havells / Polycab]

on prefixed tray/ Bracket including S&F MS clamps if required as to GS.

Through U PVC / G.I. pipe as to GS.

Supply of 1.1 KV Grade 4 Core 25 mm² XLPE Ar./ Al. Cable. [make: Finolex / Havells / Polycab]

on prefixed tray/ Bracket including S&F MS clamps if required as to GS.

Through U PVC / G.I. pipe as to GS.

Supply of 1.1 KV Grade 4 Core 16 mm² XLPE Ar./ Al. Cable. [make: Finolex / Havells / Polycab]

on prefixed tray/ Bracket including S&F MS clamps if required as to GS.

Through U PVC / G.I. pipe as to GS.

S&F G.I. pipe protection (ISI-Medium gauge) for protection of cable.

100 mm dia

80 mm dia.

S & F compression type gland complete with brass gland, rubber rings for dust & moisture proof entry of PVC armoured cables as below as per G.S.

4 core 240 sq mm

4 core 185 sq mm

4 core 70 sq mm

4 core 25 sq mm

4 core 16 sq mm

Finishing the ends of following cables by crimping method including S & F dowells solderless sockets, tapes and jointing materials etc. as per G.S.

4 core 240 sq mm

4 core 185 sq mm

4 core 70 sq mm

4 core 25 sq mm

4 core 16 sq mm

S&F of 415V 8-Way double door Vertical TPN DB in S.S. enclosure on angle iron frame / flushed on wall consisting with 1 no. 160A, MCCB (25KA,'C' curve) as incomer, 8 nos. 63A TP MCB 'C' series 10KA as outgoing complete with all accessories & interconnection with 2 nos. Cable end box as per GS. (Make-Legrand / ABB ITUS) [1 no. VTPN for Lighting/socket system of Allex Ward & 1 no. VTPN for power supply to 5 nos. AHU of Allex Ward].

S/F Double Door 6-Way TPN MCB PDB Enclosure with 1 No. 415V., 100A. 4-Pole Isolator, 18 nos. 250 V. 16-32 A 'C' series 10KA SP MCB as outgoing, complete with DIN Channel, Neutral Bar, Earth Bar with two number cable end box and other accessories flushed in wall incl. necsy. earthing attachment & mending good the damages as per GS (Make: ABB ITUS / Legrand/schneider/L&T) .

S/F Double Door 4-Way TPN MCB PDB Enclosure with 1 No. 415V., 63A. 4-Pole Isolator ,12 nos. 250 V. 16-32 A 'C' series 10KA SP MCB as outgoing, complete with DIN Channel, Neutral Bar, Earth Bar with two number cable end box and other accessories fixed by flushed in wall incl. necsy.earthing attachment & mending good the damages as per GS. ( ABB ITUS / Legrand/schneider/L&T)

S&F of Double Door Type SPN MCB BDB with DIN rail, N & E Bar and other accessories, on wall surface incl. necessary interconnection by socketing all the wire by Dowells solderless sockets as per direction of EIC as follow:-

250 V, 6-10A per way, 2+14 way double-door type SPN MCBDB with IP-42/43 protection comprising with 63A DP Isolators as incomer and 14 nos. 6-10A SPMCBs ('C' Curve, 10kA) as outgoing, flushed in wall after cutting the wall & earthing attachment as to GS. (ABB ITUS / Legrand / Schneider /L&T)

250 V, 6-10A per way, 2+10 way double-door type SPN MCBDB with IP-42/43 protection comprising with 63A DP Isolators as incomer and 10 nos. 6-10A SPMCBs ('C' Curve, 10kA) as outgoing, flushed in wall after cutting the wall & earthing attachment as to GS. (ABB ITUS / Legrand / Schneider /L&T)

250V, 2+4 Way SPN MCB DB comprising with 1 No. 250V., 40A DP Isolator as incoming and 4 nos. 6/10 A. SP MCB as outgoing as to GS. (ABB ITUS / Legrand / Schneider /L&T) [for UPS power distribution]

Distribution wiring in 1.1 KV grade 2x22/0.3 (1.5 sqmm) single core stranded 'FRLS' PVC insulated & unsheathed copper wire [make: Finolex / Havells / Polycab] partly in 20mm size PVC rigid conduit 'FR' (Precision make) [for ceiling portion only] and in 19mm bore, 3mm thick polythene pipe [for horizontal & vertical run embedded in wall], with 1x22/0.3 (1.5 sqmm) single core stranded 'FRLS' PVC insulated & unsheathed copper wire for ECC, to light/fan/call bell points with Piano Key type switch fixed on MS CRC sheet metal (16 SWG) switch board on wall complete with 2 no. “Ph & N” copper bar incl. bakelite/ Perspex top cover 3mm thick and incl. 175x100x65mm inspection box, making earthing attachment, painting the MS box and mending good the damages to original finish [only PVC Rigid Conduit on ceiling and remaining portion concealed]

Av. Run 08 Mtrs

Av. Run 10 Mtrs

Av. Run 12 Mtrs

Distn. wiring in 22/0.3 (1.5 sqmm) single core stranded 'FRLS' PVC insulated & unsheathed single core stranded copper wire [make: Finolex / Havells / Polycab] in 19 mm bore, 3 mm thick polythene pipe complete with all accessories embedded in wall to 240 V 5A 3 pin plug point incl. S&F 240 V 5A 3 pin flush type plug socket & piano key type switch (Anchor make) incl. S&F earth continuity wire, fixed on sheet metal (16 SWG) switch board with bakelite/perspex (wall matching colour) top cover (3 mm thick) flushed in wall incl. mending good damages to original finish. 2x22/0.3 (Ph. & N) and 1x22/0.3 as ECC

On Board

Average run 7.5 mtr

S&F of 240V, A.C. Superior type Call Bell on T.W. Board incl. S & F T.W. Board and making connection as to G.S.

Supplying & Fixing MS fan clam of two piece type for RC ceiling as per approved specification, fabricated from 40 mm x 9 mm MS flat including making good damages to building roof with satisfactory finishing and painting – (As per Drawing no. 475 of PWD Specification Book – May 1991)

Supplying & Fixing iron beam/ Pipe fan clamp of two piece type, as per approved specification, fabricated from 40 mm x 9 mm MS sheet flat suitable for beam having flange upto 150 mm wide – (As per Drawing no. 476 of PWD Specification Book – May 1991)

S&F of 240 V, 100 Watt (EME Step type) Electronic Fan Regulator (Make - Anchor, Cat. No. 50440)

S&F of A.C. Exhaust Fan (EPC Electrical Pvt. Ltd. - Heavy Duty) incl. S&F 12mm thick Water proof Ply board (approved make) or Cutting hole on wall, S&F Louver Shutter (Aluminium) with Nuts, Bolts, washers etc. on wall and mending good the damages to original finish as follows :-

240 V, 1370 RPM, 230 mm. (9") Dia [for small toilets]

240 V, 1420 RPM, 300 mm. (12") Dia [for toilet blocks]

S&F of "L" shape Cowl made of G.I sheet of size 300x300mm having length 600mm with 4 nos 20x3mm MS flat support and S&F of wire mess at the ends of the said cowl with nuts, bolts etc as reqd. for Exhaust fan. (for lift m/c room & panel room)

Cutting channel of 31 mm x 31 mm size on masonry wall incl. S&F heavy gauge polythene pipe dia as stated below, by means of iron hooks and supplying and drawing 18 SWG GI Wire fish wire incl. mending good damages to building works 13 mm dia 3 mm thick polythene pipe without earth continuity wire

Cutting channel of 40 mm x 40 mm size on masonry wall incl. S&F heavy gauge polythene pipe dia as stated below, by means of iron hooks and supplying and drawing 18 SWG GI Wire as fish wire incl. mending good damages to building works 19 mm dia 3 mm thick polythene pipe without earthcontinuity wire

Supplying & Fixing sheet metal inspection box (16 SWG) of the following sizes flushed in wall by housing the same after cutting brick wall incl. making earthing attachment, painting and mending good damages to building works

100 mm x 100 mm x 65 mm

150 mm x 100 mm x 65 mm

175 mm x 100 mm x 65 mm

200 mm x 150 mm x 65 mm

S & Drawing of following sizes PVC insulated FRLS Cu wire (Make- Finolex / Havells / Polycab) in 19mm dia 3mm thick polyethelene pipe embedded in wall complete with all accessories on wall incl. making connections as to G.S.:-

3 x 1.5 mm² for separate plug boards

2 x 2.5 & 1 x 1.5 mm² for power plug, Computer/power socket Boards.

2 x 4 & 1 x 2.5 mm² from TPN PBDB for 3KW sterilizer/hot water drum points

2 x 6 & 1 x 4 mm² for SPN DB

4 x 10 mm² & 2 x 6 mm² for sub-main wiring from VTPN to 3-ph loads.

4 x 16 mm² & 2 x10 mm² for sub-main wiring from VTPN to TPN power DBs.

Finishing the end of following sizes copper wire end with dowells solderless socket by crimping method as pre GS as follows :-

2 x 2.5 & 1 x 1.5 mm² cu. wire

2 x 4 & 1 x 2.5 mm² cu. wire

2 x 6 & 1 x 4 mm² cu. wire

4 x 10 & 2 x 6 mm² cu. wire

4 x 16 & 2 x 10 mm² cu. wire

S&F of 16 SWG M.S. box of following sizes with 3 mm. thick suitable size bkt top cover and earthing attachment incl. making connection as per GS as follows:-

12" x 10" x 2½" comprising with 2 No. 250V 6-pin 16A plug socket & 2 Nos. 16A piano key type switch and 2 nos. 250V. 6A. 5-Pin plug socket & 2 nos. 6A Piano Key switch and 1 no. Indicator (all Anchor make)

7" x 4" x 2½" comprising with 2 Nos. 250V. 5-pin 6A plug socket with 2 Nos. 6A piano key type switch (Anchor)

Supply & Fixing 240 V, 20A, plug socket with separate 20 A Piano key type switch (Brand approved by EIC) on sheet metal switch board embedded in wall incl. S & F 150x100x65mm MS (16SWG) switch board and bakelite/perspex top cover of 3mm thick by Brass screws after making housing for switch by cutting bakelite/perspex cover and making necessary connections as required.

S & F 48″ sweep, 230V 1-Ph. AC ceiling fans incl. all accss. The capacitor of fan must be P-2 type brust proof & must have safety wire directly linked from fan hook to stator of fan. (Make - CG HS PLUS, 5 star rated / EPC/Orient having Similar Specification) Incl engraving & painting the Deppt number up to 15 digits.

S&D of 230V, 18" (450mm) 4 (four) Blades Industrial type Air-Circulator Pedestal Fan complete with all accessories such as Regulator, Cord and 15 Amp. 3-pin Top (Make - E.P.C. Electrical Pvt. Ltd., Heavy Duty)

S&F of 240V, LED tube light fittings suspended 25 cm. below the ceiling by 2 nos. 20mm. Dia. E.I. Conduit support with, MS 'L' clamp and necy. Electrical connection by 2 x1.5 mm² PVC insulated Cu. Wire & painting as follows:-

Single LED T8 T/L fittings [Philips TMC 501 P 1xT-LED 22W P3241) incl. 1x MAS LEDtube 1200mm 18W865 T8 I (PC Body)/ Equivalent product of Crompton/Wipro having similar specification in all respect].

Twin LED T8 T/L fittings [Philips TMC 501 P 2xT-LED 22W P3242) incl. 2x MAS LEDtube 1200mm 18W865 T8 I(PC Body) Equivalent product of Crompton/Wipro having similar specification in all respect].

Supply of recess mounted 2' x 2' LED luminaries fixed on false ceiling after cutting false ceiling as per direction of the EIC. (Philips Model RC 380B LED 36S-6500 G4 L60W60 PSU OD/ Equivalent product of Crompton/ Wipro having similar specification in all respect)

S & D of 240V, 12 watt recess mounted round slim panel LED downlight . [Make - Philips, cat no DN 193 LED 12S 6500 PSU WH S1/ Wipro, Cat No LD90-141-XXX-65-XX/ Bajaj BZSLO 12W WH PRO].

S&F of surface mounted 10W LED downlight luminaire. (Philips / Jaquar / Wipro)

S&F of extra Conduit for suspension of FTL fittings exceeding 25 cm with additional 2 x 20 mm dia EI Conduit supports & necessary inter-connection by 3 x 1.5 mm² S/C PVC Cu. Wire, painting etc. as to GS.

S&F of down rod (14 SWG MS) for hanging ceiling fans from extra high ceiling including & necessary inter-connection by 3 x 1.5 mm² S/C PVC Cu. Wire and duly painting of down rod as to GS.

Supply & fixing of LED signage in box type Aluminium frame fabricated from 40 mm x 25 mm x 2mm thick aluminium square hollow bar with cross and radial supports in the middle of the structural frame properly fixed with the structure incl all necessary fixing materials and fabrication works and the board shall rest on the wall with suitable sizes MS angle (50mm x 50mm x 6mm) bracket/frame arrangement to be fixed by anchor fasteners/ inserting in wall including S/F following accessories as per direction of the EIC. [Size of the signage : 10 ft x 3 ft = 30 sqft.]

incl. S&F of ACP Board made 4 mm thick ACP sheets (Make- Alstrong/ Aludecor/ Timex Bond ) - 96 sqft.

incl. S&F of superior quality acrylic three dimensinal letter flushed on the pre-fabricated existing ACP board. The computerised processed letter in bold English fonts and letter size of the matter shall be as below (to be approved before taking up) :

DEPARTMENT OF PAEDIATRIC MEDICINE (12") / ALLEX WARD (12") / ALLEX EXTENTION WARD (12")

incl. S&F of 12V DC LED modules having three LED in a single base module including necessary electrical connections. [minimum 12 modules per letter]

Specification of the LEDs is given as below : a) LED – white, GE/ Samsung (Cat No. Tetra mini max, Code No. GEWHMMTS8) b) Type – straight, 3 Nos. Led per module c) Life – 70,000 burning hours. d) Visibility – 100 mtrs at least, for normal eye

e) Power supply -20 Amp. (GE) f) Power consumption – 1.5 watt per module g) Input – 230V AC, output 12V DC (Double LED layer)

incl. S&F of heavy duty 12V DC, 400 VA SMPS (Make- Reputed & approved by EIC) as per VA load.

Supply & Fixing of perforated GI cable tray with perforation not more than 17.5% suspended from ceiling incl. S/F GI connector, 6mm dia MS suspender, bolts & nuts, steel fastner etc. as required of size 200 x 50 x 1.25mm (18 SWG) with 25x25x3mm angle iron support & painting as per GS.

Connecting the equipments to earth busbar incl. S & Drawing No. 8 SWG G.I. earth wire as to G.S.

S&F of Earth bus-bar of Galvanized MS flat 25 mm x 6 mm including nuts, bolts & washers etc. as to GS.

Earthing installation with 50mm dia (ISI-Medium) G.I. pipe x 3.04 Mtrs. Long and 1 no. 4 SWG G.I wire (4 mtrs. Long) incl. bolt, double nuts & washers for Soft Soil incl. excavation of soil as to GS.

1. The Agency must procure the materials from the manufacturer / OEM or from their authorized. sales channel so that the standard warranty / support of the Manufacturer / OEM becomes applicable to the products to be delivered and installed by them. 2. Documents that authenticates such procurement form the manufacturer / OEM or from their authorized sales channel and standard warranty / support should be sent from the e-mail of the manufacturer /OEM / authorized sales channel to the e-mail of Engineer-in-charge and hard copy of it to be submitted during execution of work/submission of bill. 3. If any refurbished material is supplied and installed, penal action will be taken as per existing rules.

Defect Liability period 1 (One) Year

(Rates should be Quoted inclusive of all taxes & duities and L.W.C. @ 1% as applicable)

Prava Enterprise

JAYBEECO