Installation of the Medical Gas Pipe Line with repairing of existing 2 Nos. rooms for accommodation of Gas storage (manifold room) and compressor (plant room) of MMCH (Including Electrical works)

Amount

Item no.1/ Demolishing the plastering from walls/ R.C.C. and P.C.C. members without causing any damage to the wall/ member upto any height including disposal of debris as directed for all levels

Demolishing plain cement concrete including disposal of debris as directed for all levels (i) Prop (1 : 4 : 8) or leaner mix

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (b).Brick on edge soling

Plain cement concrete floor base in prop 1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. c) 100mm thick

(a) Removing white or colour wash by steel wire brushing and/ or scraping, sand papering and preparing the wall surface smooth including necessary repairs to scratches complete.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side b) In cement mortar 1:4

Demolishing brickwork including stacking of serviceable materials and disposal of unserviceable materials as directed for all levels

Providing corrugated galvenised Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvenised J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc. (Roof trusses and purlin etc.to be measured and paid separately).

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mmx10mmx2mm braced with flat iron diagonals 20mmx5mm size with top and bottom rails of T-iron 40mmx40mmx6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing, fitting and fixing anodised aluminium partition walls of standard sections of approved brand, joints mitred and welded (manufactured to relevant I.S. specification) and providing and fitting angle cleat, rubber gasket, bolting device screws etc. at all levels. (iv) Prelaminated Board

Providing two coats of Birla White Wall Care Putty (Water Resistant White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm) (ii)Thickness = 1.0mm thick

m) Distempering two coats with oil bound distemper of approved brand and manufacture and of required shade on new wall surface to give an even shade, over and including a priming coat with distemper primer of approved brand and manufacture after throughly brooming the surface free from mortar dropings and other foreign matter and including preparing surface even and sand papered smooth. (i).Priming coat with distemper primer

(ii). Top coat

230mm thick brick wall in cement morter with 1st class brick including racking out joints and curing complete as directed in structure (I) In Sub-structure upto plinth level including dewatering if necessary (b). In proportion 1:4.

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately) (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth level. N) Without using admixture, plasticiser a) M15 grade concrete or Prop. 1:2:4

(B) In super structure from plinth level up to 1st floor level. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral staircase and landing ) including preparing the top surface and finishing of nosing. N) Without using admixture, plasticiser a) M15 grade concrete or Prop. 1:2:4

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (b) In hard/ dense soil

"Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C. work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) " a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (ii)Super Ductile (SD) TMT reinforcement bars

Providing, fitting, hoisting and fixing of roof trusses fabricated using any one or conmbination of following sections of (i) Square (ii) Rectangular Hollow section of specification SHS/RHS and including purlins, bottom runners and providing M.S. cleat, M.S. angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S. code 4923 : 1997

Supplying fitting and fixing M.S.angles, M.S. flat, M.S. bolts and nuts including painting with red lead paint one coat complete as directed. a) M. S. Angles…….

c) M. S. bolts & nuts…….

Providing corrugated galvenised Iron sheet roofing of TATA SHAKTEE / SAIL including fitting and fixing necessary galvenised J or L hooks, bolts and nuts 8 mm dia with bitumen washer 25 mm dia x 3 mm thick and 1.6 mm thick limpet washer complete excluding cost of roof truss, purlin etc. (Roof trusses and purlin etc.to be measured and paid separately). (a) 0.45 mm thick

Providing galvd iron ridging of TATA SHAKTEE / SAIL including supplying and fixing necessary galvd screws/washers etc. complete as directed.

1st class brick nogged wall in cement mortar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall

Providing, fitting and fixing powder coated pressed steel door frame made of 1.25mm/ 1.6mm thick sheet of various sizes with necessary hinge jamb, lock jamb, head and steel base ties at the bottom of the frame. The whole frame shall be welded or rigidly fixed together by mechanical means with base ties of pressed mild steel angle of size 20x20x1.25mm thick. Frame to be filled up with 1:4:8 P.C.C. after fitting the frame with brick/ concrete works etc.complete as directed by the department for all levels. (P.C.C. to be measured and paid for seperately). (b) 1.60mm thick sheet (ii) Size 105mm x 60mm (Single rebate)

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. b) Non decorative type and block board core. (i) 40 mm thick .

Providing, fitting and fixing steel windows of standard rolled steel sections as per relevant I.S. Code, joints mitred and welded with 15mmx13mmx100mm lugs embedded in cement concrete block of M-10 grade including providing and fixing of projecting hinges (not more than 65mm and not less than 15mm wide) bolting device, steel handles, pegs, stays of 300mm long etc. complete including providing 12mmx12mm sq. bars duly welded to steel frame at not more than 12cm c/c applying a priming coat of red-lead paint etc. complete as per drawing. a) Openable

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (d) With stone dust obtained by truck carriage including loading and unloading to the site of work.

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a).Brick on flat soling.

Plain cement concrete floor base in prop 1:3:6 laid in alternate bays as specified with coarse agg. of size 13mm to 32mm including dewatering if necessary, and curing etc. complete. C) 100mm thick

15 mm thick Cement plaster in single coat on single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smooth including curing complete as directed. A) On rough side c) In cement mortar 1:5

B) On fair side c) In cement mortar 1:5

Providing two coats of acrylic water based wall putty/ wall filler of Asian Paints/ Berger/ Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and external after removing all the loosely adhering material from the wall/ ceiling surface with the help of emery stone, putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department.

(n) Distempering two coats with oil bound distemper of approved brand and manufacture and of required shade on new wall surface to give an even shade, over and including a priming coat with alkali resistant primer of approved brand and manufacture after throughly brooming the surface free from mortar dropings and other foreign matter and also including preparing the surface even and sand papered smooth. (i).Priming coat with alkali resistant primer

(ii). Top coat

Providing plinth protection with bricks laid on edge and grouted with cement mortar 1:4 and finishing with cement pointing in prop. 1:1 complete.

Providing drain with brick work in cement mortar in proportion 1:5 with half brick thick side walls and 100mm thick C.C (1:3:6) base over one brick flat soling including 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. ii). 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining ,fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. a) In exposed surfaces or in trenches. (i) 160mm dia.

Supplying fitting and fixing G.I. Pipes of following sizes, with all necessary 'R' brand or similar approved G.I. Fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, H.W. clamps etc.complete at all levels including below G.L. as directed and specified. (A) Exposed on walls a) 50 mm dia (Medium) i) Using Tata make

f) 15 mm dia (Medium) i) Using Tata make

Supply, Installation, Testing & commissioning of Terminal Units (Gas Outlets) with probes/ Adaptors as per CE marked. The outlet will be equipped with a primary and secondary check valve with suitable pressure for (O2, cleared for medical gas a and pressure tested, inlet pipe can be swiveled 360 degree for ease of installation all as specified and directed. MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW

Supply, Installation, Testing & Commissioning of Oxygen Flow meter as per CE marked, made with chrome plated brass body, Graduated flow tube and cover made of polycarbonate 7 unbreakable. Adjustable flow by needle valve (know) with micrometrical regulation. Humidifier bottle is made of unbreakable polycarbonate material and is autoclavable.

Supply, Installation Testing Commissioning of High pressure Tubing Flexible having antistatic Core as per ISO standards with proper colour coded for O2, N2O, compressed Air and Vacuum complete all as specified and directed. 5mtr long

Supply, Installation Testing Commissioning of Terminal Units (Gas Outlets) as per CE marked with probes/ Adaptors. The outlet will be equipped with a primary and secondary check valve with suitable pressure for (NO2), cleaned for medical gas and pressure tested, inlet pipe can be swiveled 360 degree for ease of installation all as specified and as directed. 360 degree for ease of installation all as specified and as directed. MAKE : W.H.S./UNITED MEDICAL ENGNEERS.GFLOW

upply, Installation, Testing and Commissioning of Units (Gas Outlets) as per CE marked with probes /Adaptors. The outlet will be equipped with a primary and secondary check valve with suitable prepssure for complete all as specified and as directed for the following- For Compressed Air (4Bar) Make : WHS/UNITED MEDICAL ENGINEERS/GFLOW

For Compressed Air 7Bar) Make : WHS/UNITED MEDICAL ENGINEERS/GFLOW

Supply, Installation, Testing & Commissioning of Terminal Units (Gas outlets) as per CE marked for vacuum with probes /Adaptors. The outlet will be equipped with a primary and secondary check valve with suitable pressure for (Vacuum), cleaned for medical gas pressure tested inlet pipe can be swiveled 360 degree for ease of installation al as specified and as directed. MAKE : W.H.S./UNITED MEDICAL ENGNEERS.GFLOW

Supply, Installation, Testing & Commissioning of ward vacuum Unit as per CE marked with Regulator along with vacuum gauge, collection jar of 600ml capacity reusable plastic collection bottle with over flow safety tap wall mounted type with bracket complete all as specified and as directed . MAKE : W.H.S./UNITED MEDICAL ENGNEERS.GFLOW

Supply, Installation, Testing & Commissioning of Theatre Suction Unit, Trolley as per CE marked. The unit illustrated incorporates a vacuum regulator with e.g. (0.760 MM/HG), two suction jars of 2000 ml capacity each (4000ml_. A there way valve which allows use of either or both suction jars. The rugged structure is made of mild steel & fiber glass to forbear hard usage & for attractive clinical appearance. Branches chassis is provide with castors for easy mobility. MAKE : W.H.S./UNITED MEDICAL ENGNEERS.GFLOW

COPPER PIPE AS PER MEDICAL GRADE 12mm OD x 0.7mm Thick

15mm OD x 0.9mm Thick

22mm OD x 0.9mm Thick

28mm OD x 0.9mm Thick

42mm OD x 1.00mm Thick

Supply, Installation, Testing & Commissioning of Zonal valve Box, are fully designed to suit multiple operational and requirement and ensure considering space for mounting. The configurations are valve Boxes are described :- 3 Gas Services O2, Air, Vacuum

5 Gas Service O2, N2O, Air 4 Bar, Air 7 Bar, Vacuum

Supply, Installation, Testing & Commissioning of Area line pressure Alarm with display for various faults indications and capable of monitoring maximum 5 medical gas service by means of pressure switches etc. with audible warning with automatic reedit when the gas service returns to normal as per standard specifications CE Marked all as specified and as directed for the following Area line pressure Alarm :- 3 Gas Services O2, Air, Vacuum

5 Gas Service O2, N2O, Air 4 Bar, Air 7 Bar, Vacuum

Supply, Installation, Testing & Commissioning of insolation Valves with brass body with nick el plate valve operating handle suitable for 12mm OD copper pipe to 42 mm OD copper pipes with brass adapted as per standard specifications all as specified and as directed for the following insolation Valves :- 12mm OD x 0.7mm Thick

15mm OD x 0.9mm Thick

22mm OD x 0.9mm Thick

28mm OD x 0.9mm Thick

42mm OD x 1.00mm Thick

Supply, Installation, Testing & Commissioning of Moveable pendant single Arm is having the operational of only horizontal way comprising moveable ceiling pendant CE Marked with 1 x 1000mm long arm having weight carrying capacity of more than 80 Kg, 4 no’s 6/16 Amp Anti-Bacterials Socket 1 no. Monitor shelf and 6 no’s provision of gas outlets (each single arm pendent having these above said accessories.) MAKE : W.H.S./UNITED MEDICAL ENGNEERS.GFLOW

Low pressure Tubing (Transparent)

Supply, Installation, Testing & Commissioning of Horizontal Bed Head panel 5 Ft/ long , CE Marked. These are extruded Aluminum panels, dully powder coated as per customers choice of colour to maintain the aesthetics of the hospital along with accessories like 01 no’s of I.V. Hook, 01 no’s of Utility B.P. Basket, 01 no’s of Monitor Tray, 01 no’s of Aluminum Clamp for Ward Vacuum Unit, 01 no’s of LED Examination Light and 02 no’s of 6/16 Amp Anti Bacterial Switch & Sockets. MAKE : W.H.S./UNITED MEDICAL ENGNEERS.GFLOW

Supply, Installation, Testing & commissioning of Oxygen manifold extendable type 5+5 size complete as per CE marked with middle frame with chain for individual cylinder and high pressure annealed copper tail pipes with 1 end having brass adaptor and other end suitable for manifold non return valves and manifold will have 10 brass non return valves for individual oxygen cylinder, middle frame with circumferential M.S. Flat duly power coated all as specified and as directed. MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW Note : The cylinder shall not be included on this rate.

Supply, Installation, Testing & Commissioning of Fully Automatic Digital Gas Control panel for O2, two stages of pressure regulators will be provided in the control cabinet for pressure regulation. One delivery pressure regulator in service and another will be standby mode, panel will be in a enclosure and automatically changeover from the primary supply to secondary supply bank without any fluctuation, changeover will be perform by electrically/ pneumatically valves. Fully atumatic control panel when the gas cylinders get empty either, left bank or right bank. Futures :- i)The control panel cover is made using high quality M.S. Duly power coated. ii)The supply of Gas does not depend on electricity. iii) Display is provided with built-in led to indicate high, normal and low line pressure. iv)Panel cover is fitted with lock to prevent unauthorized access, and can be swung open for maintenance. v) It includes pressure gauge (63mm) that indicated the gas pressure of each header and pipe line distribution pressure. vi) Capable to supply a distribution flow rate in excess of 2500 LPM. Vii) Manufactured by CE certified/ISO 9001-20808 Organization.

Supply, Installation, Testing & Commissioning of 2+2 Cylinders Emergency Oxygen Manifold as per CE marked with to stage high flow rate regulator with NRV for every cylinder and copper tail pipes with top and middle frame for Oxygen all as specified and as directed. MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW Note : The cylinder shall not be included on this rate.

Supply, Installation, Testing & Commissioning of one 3+3 Nitrous (N2O) manifold as per CE marked with two stage high flow rate pressure regulator with NRV for every cylinder and copper tail pipes complete all as specified and as directed. Note : The Cylinder shall not be included on this rate. Note : The cylinder shall not be included on this rate MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW

Supply, Installation, Testing & Commissioning of one 1+1 Cylinder Emergency Nitrous (N2O) manifold as per CE marked with to stage high flow rate regulator with NRV for every cylinder and copper tail pipes complete all as per specified and as directed. MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW Note : (The cylinder shall not be included on this rate)

Supply, Installation, Testing & Commissioning of Fully Automatic Digital Gas Control panel for O2, two stages of pressure regulators will be provided in the control cabinet for pressure regulation. One delivery pressure regulator in service and another will be standby mode, panel will be in a enclosure and automatically changeover from the primary supply to secondary supply bank without any fluctuation, changeover will be perform by electrically/ pneumatically valves. Fully atumatic control panel when the gas cylinders get empty either, left bank or right bank. Futures :- i)The control panel cover is made using high quality M.S. Duly power coated. ii)The supply of Gas does not depend on electricity. iii) Display is provided with built-in led to indicate high, normal and low line pressure. iv)Panel cover is fitted with lock to prevent unauthorized access, and can be swung open for maintenance. v) It includes pressure gauge (63mm) that indicated the gas pressure of each header and pipe line distribution pressure. vi) Capable to supply a distribution flow rate in excess of 2500 LPM. Vii) Manufactured by CE certified/ISO 9001-20808 Organization.

Supply, Installation, Testing & Commissioning of Duplex Air Compressor 5 HP each Double stage high pressure Air Compressor (5HP) each are designed for high pressure applications. These compressors have extra heavy- duty components and are and are designed for minimum maintenance and maximum performance. High pressure air compressor, Durable cast iron. Intermediate duty applications. 5 HP Air Compressor motor including necessary Accessories like air Dryer, 500 Ltr Air Receiver Tank with safety valve, pressure Reducting Station for Air -4 & Air -7 and filtration System. Manufactured by CE certified.ISO 9001-2008 Organization.

Supply, Installation, Testing & Commissioning including connection of complete Vacuum plant. The pump should be achieve vacuum upto 737 mm (290’ Hg) for single stage upto 754.4mm (29.7 Hg) for two stage configuration at sea level. 5 HP each Double Stage Vacuum pump including necessary Vacuum Accessories like Silencer, Receiver Tank (500 Ltr) & Vacuum Bacteria Filter.

Supply, Installation, Testing & commissioning of Terminal Units (Gas Outlets) as per CE marked with probes. Adaptors. The outlet will be equipped with a primary and secondary check valve with suitable pressure for (O2), cleared for medical gas and pressure tested, inlet pipe can be swiveled 360 degree for ease of installation all as specified and as directed. MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW

Supply, Installation, Testing & Commissioning of Oxygen Flow meter, made with chrome plated brass body. Graduated flow tube and cover made of polycarbonate 7 unbreakable. Adjustable flow by needle valve (know) with micrometrical regulation. Humidifier bottle is made of unbreakable polycarbonate material and is autoclavable as per CE marked. MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW

Supply, Installation, Testing & Commissioning of High pressure Tubing Flexible having antistatic Core as per ISO standards with proper colour coded for O2, N2O, Compressed Air and Vacuum complete all as specified and directed. 5mtr long.

Supply, Installation, Testing & Commissioning of Terminal Units (Gas Outlets) as per CE marked with probes/Adaptors. The outlet will be equipped with a primary and secondary check valve with suitable pressure for compressed Air (4 Bar) MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW

Supply, Installation, Testing & Commissioning of Terminal Units Units (Gas Outlets) as per CE marked with probes/Adaptors. The outlet will be equipped with a primary and secondary check valve with suitable pressure for (Vacuum), cleared for medical gas and pressure tested, inlet pipe can be swiveled 360 degree for ease of installation all as specified and as directed. MAKE : W.H.S./UNITED MEDICAL EBGINEERS/GFLOW

Supply, Installation, Testing & Commissioning of Ward Vacuum Unit as per CE marked with Regulator along with vacuum gauge, collection jar of 600ml capacity reusable plastic collection bottle with overflow safety tap Wall mounted type with bracket r complete all as specified and as directed Wall mounted type with bracket complete all as specified and as directed MAKE : WHS/UNITED MEDICAL ENGINEERS/GFLOW

Copper pipe : AS PER MEDICAL GRADE 12mm OD x 0.7mm Thick

15mm OD x0.9mm Thick

22mm OD x 0.9mm Thick

Supply, Installation, Testing & Commissioning of Zonal Valve Box, are fully designed to suit multiple operational and requirement and ensure considering space for mounting. The configurations are Valve Boxes are described :- 3 Gas Services-O2,Air, Vacuum

Supply, Installation Testing Commissioning of Area Line pressure Alarm with display for various faults indications and capable of monitoring maximum 5 medical gas service by means of pressure switches etc. with audible warning with automatic reedit when the gas service returns to normal as peer standard specification CE marked all as specified and as directed for the following Area line pressure Alarm :- 3 gas Alarm

Low pressure Tubing (Transparent)

Supply, Installation, Testing and Commissioning of Horizontal Bed Head panel. 5 Ft. long, CE Marked These are extruded Aluminum panels, dully powder coated as per customers choice of colour to maintain the aesthetics of the hospitals along with accessories like 01 no’s of I.V. Hook, 01 no’s of Utility B.P. Basket, 01 no’s of Monitor Tray, 01 no’s of Aluminum Clamp for ward Vacuum Unit, 01 no’s of LED Examination Light and 02 no’s of 6/16 Amp Anti Bacterial Switch & Sockets. Make : WHS/UNITED MEDICAL ENGINEERS/GFLOW

Wiring for light/ fan/ call bell point with 2x1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/ bell push (Anchor Penta/Gold medal /Kolor kany.Kom/ Havells or equivalent make as approved by the Deptt.) GI/ MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover ,ceiling rose (Anchor/Gold medal /Kolor kany.Kom / Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt. Short point up to 3.00 metre. length.

Medium point up to 6.00 metre. Length.

Long point up to 10.00 metre. Length.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq. mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) with flat 19 mm ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) in surface system, including providing and fixing 5/6 pin 16 Amps flush type socket outlets and 16 Amps flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.), GI/ MS switch board (I.S.I. marked) with phenolic laminated sheet cover earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete. Extra Long point up to 15.00 metre. length.

Wiring for 5 pin 6 amp plug with 1.5 sq mm P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) including providing & fixing 5 pin 6 amp socket outlet (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) and 6 amp flush type switch (Anchor penta /Gold medal /Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) earthing the 3rd pin of the socket as required on the switch board in flat ISI marked casing 'n' capping system, when fitted on same board of light and fan.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface/ recessed PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) wiring system. With 2 x 1.5 sq. mm. cable in 20 mm dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

2.7). Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) PVC conduit (Berlia/ AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) including earth continuity in surface/ recessed 20 mm. dia. 2mm thick/ heavy ISI marked IS: 9537 PART - III rigid PVC conduit wiring system. With 2 x 2.5 sq. mm. + earth continuity with 1x1.5 sq. mm. in flat 19 mm ISI marked casing 'n' capping system.

With 2 x 4 sq. mm. + earth continuity with 1x2.5 sq. mm. cable in 20 mm. dia. 2mm thick/ heavy rigid PVC IS: 9537 Part - III conduit.

SB. 8.13). Supplying including and fixing of following Metal boxes for MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) in surface/ recessed system complete as per direction of department. 3 module type Metal

8 module type Metal

SB. 8.14). Supplying including fitting fixing of following MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) front plate of suitable colour as per direction of department. 3 module

8 module

Supplying including fitting and fixing of Call bell indicator with register 6 A ,250 V A.C 1 way 5P 1 module complete as directed and specified by the deptt. (Model Ref. 573415 Legrand/ equivalent make) 1.Call bell with indicator(Legrand/ C&S or equivalent as approved by the Deptt.) make)

Supplying with fitting and fixing of 120 watt electronic modular STEP speed control 2 - module type MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department. 120 watt electronic modular step speed control 2 - module type

Supplying with fitting and fixing of 6 amp one way modular clip in bell push MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including installation of socket outlet 6/10/13 Amps INTERNATIONAL SOCKET , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing of 6/10 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying including installation of socket outlet 10/16 Amps 3/5 pin combine shuttered complete , MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE(MURANO) including making necessary connection as per direction of department.

Supplying with fitting and fixing sheet steel, phosphatised, powder painted Single door surface mounting vertical TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar 125A and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. Richa, Bentec, Adhunic, V-Guard make) 8 way TPN (8+24) single door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted Single door surface mounting TPN MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. ABB, Schneider MG, legrand, Hager make) 4 way TPN (4+12) Single Door

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (Schneider MG, legrand, Hager make) 6 to 32A

Supplying with fitting and fixing DP 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make) 40A

Supplying with fitting and fixing 4P 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make) 40A

Supply, installation & testing of Copper Plate earth station with 600 mmx600 mmx3 mm copper earth plate with necessary 40 mm dia. G.I. medium duty watering pipe with G.I. Fittings such as Socket, Tee, elbow, nipple and 50 mmx40 mm G.I. reducing socket for funnel including locking arrangement with 300 mmx300 mmx6 mm C.I. hinged cover plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt .

Extra for using salt 5 Kg and Charcoal 96 Kg in G.I./Copper plate Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt .

Supplying & laying of 8 SWG Copper earth drawn through 15 mm dia. Medium quality G.I. pipe from Earth Electrode (below G.L.) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying fitting and fixing of LED batten tubes high quality alluminium extruded with decorative end caps connection with 1.5 mm2 1core PVC insulated round copper conductor as required and as directed by the department. LGL 1X 020 X C/LGLZo1X020XCN//LGLZO 1X020XCW (20W).

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR Kabel /Nicco / Anchor or Equivalent Make as approved by the Deptt.) in surface flat ISI marked casing 'n' capping (AKG / Precision/ Presto Plast/Polycab/ MW or equivalent make as approved by the Deptt.) system including earth continuity. With 4 x 10 sq. mm. + earth continuity with 2x6 sq. mm. cable in flat 32 mm ISI marked casing 'n' capping system.

Supplying including fitting fixing of following A.C. Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department [Without regulator]. Premium model 1200 mm Sweep (ORIENT PSPO make) / Premium model 1050 / 1200 mm Sweep SS-390 Deco Havells make)

Supplying including fitting fixing of following A.C. Exhaust fan in the existing hole on the wall of following sweeps with making necessary connection as approved by the Deptt.)as required complete and as directed by the Department. Domestic Ventilator RX 150 mm sweep (ORIENT make), Brisk Air 150 mm sweep Louver type (Crompton make)

Supplying including installation, connection as approved by the Deptt., testing and commissioning of CENTRIFUGAL VERTICAL PUMP SET complete as directed and specified by the deptt. 5 HP three Phase vertical multistage high pressure centrifugal pump set 10 stage (Crompton Greaves/ Aquatic/ CRI/ V-Guard make) with Star delta Starter ( Crompton Greaves/ Control & Switch Gear/ BCH/ L& T / Siemens make) Fully Automatic citation

Supply and laying of following size Power/Control Copper cables, Solid Copper conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, Unarmoured/Armour (Galvanised for cables up to 10 x 1.5 sq mm.8 x 2.5 sq mm.2 x 10 sq mm.3 x 10 sq mm.4 x 6 sq mm balance all galvanised steel strip) , extruded PVC Type ST2 Sheathed, 650/1100 V grade as per IS 7098 (Part 1) 1988, LT armoured U.G. cable laid in pucca flooring, road crossing, drain crossing as per site requirement and partially in air to connection as approved by the Depts. the control switch, through medium duty G.I. pipe (Tata/ Nezone make or equivalent as approved by the Deptt) bend and socket including excavation and refilling the trench and making good damage done as specified and directed by the deptt. (Nicco/ Havells/ RPG/CCI/Polycab/Gloster/ Finolex make) Core - 4 2XWY 2XFY 35.00 Sq.mm 4 Core U.G. cable in 50mm dia medium duty hot dip galvanised pipe (AKG or equivalent as approved by the Deptt.)

OM CONSTRUCTIONS