PROVN OF TOILET BLOCK WITH BATHROOM NEAR BLDG NO A/4/138 OR LIVING, PROVN OF HARD STANDING FOR B VEH REPAIR SECTION AT 309 FWC, PROVN OF COVERED WASHING AREA WITH VEH WASHING POINT AT D PARK, PROVN OF MT STORE AT 17 CORPS MT AT PMS

Amount

Surface dressing n exc 15 cm deep and getting out in soft/loose soil Complete all as specified and directed.

Excavating in trenches , n.exc 1.5 m wide and n.exc 1.5 m depth for foundation etc or for shafts, wells, cesspits ,manhole pier hole, laying of cables, pipes etc n.exc 10 sqm on plan and n.exc 1.5m in depth and getting out in any kind of soil Note : Manual excavation to be done. During excavation if any damage occured to existing cable any type/ water pipe line, it will be contractor responsibilty to get it repair and make functional by providing jointing kit etc without any extra cost. Contractor has to repair it within 24 hrs so that essential service can not be effected due to such damage.If contractor fails to repair it within 24 hrs penalty @ Rs 500/- will be charged to contractor. In this GE decision will be final, conclusive and binding.

Excavating over areas in soft/loose soil, n exc 1.5 m deep and getting out, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, and well ramming in layer not exceeding 25 cm thick in soft/loose soil complete all as specified and directed.

Removing surplus excavated spoil/earth to a distance not exc.50M and deposited where directed at a level not exc.1.5 M above the starting point.

M&L sand filling in floors or pavings, laid in layers n exc 15 cm thick, spread, levelled and blinded with earth and rammed incl watering complete all as specified and directed.

M&L for hardcore of broken stone or boulder of gauge exc 63mm but n.exc 75 mm deposited, spread & leveled in lyers n.exc 15 cm thick watered & rammed to a true surface Complete all as specified and directed.

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering and all as specified and directed.

Rolling and consolidating formation surfaces in cutting with power roller exc 8 tonne and n.exc 12 tonne complete all as specified and directed.

M&L for 450/500 mm thick (compacted) in layers of each 100mm thick in pavings, with mix of fly ash, clinker & stone dust in the proportion of 1:3:6 (ie 10% fly ash, 30% clinker and 60% stone dust ) laying in layers n. exc 10cm thick, watering, ramming and compacted with hand/power roller 8 to 12 tonn roller to required camber and gradient complete all as directed by Engineer-in-Charge.

M&L for Soling (or sub base) of 150 mm thickness with broken boulders or quarried stone, inter stices filled, surface formed and rolled and consolidated to required gradient and camber, complete all as specified and as directed.

M&L for 150mm cm thick (compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required, complete all as specified and as directed.

M & L for Plain Cement Concrete Type D2 14:8 (using 40 mm graded stone aggregate) as foundation and mass filling Complete all as specified and directed.

M & L for Plain Cement Concrete Type C2 1:3:6 (using 40 mm graded stone aggregate) as foundation and mass filling

M&L for Design mix M-25, using 20 mm graded stone aggregate as in footings fdn beams complete all as specified and directed.

M&L for Design mix M-25, using 20 mm graded stone aggregate as in coloums complete all as specified and directed.

M&L for M-25 Design mix using 20mm stone aggregate Beams, cantilevers, bressummers, lintels over 1.5m span Complete all as specified and directed.

M&L for Design mix M-25, using 20 mm graded stone aggregate as in chajja complete all as specified and directed.

M&L for Design mix M-25, using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns, in roofs and in shelves and the like complete all as specified and directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in coping, benching. Hauncing etc finished even and smooth Complete all as specified and directed.

M&L Plain Cement Concrete 1:3:6 type C1 (using 20 mm stone aggregate) as in surface channels and drains, complete all as specified and directed.

M&L RCC 1:2:4 type B1 using 20mm stone aggregate as in preacast man hole cover slabs set in CM 1:6 Complete all as specified and directed.

M&L for damp proof course 25mm thk M-20 (Nominal Mix) using 12.5mm graded stone aggregate with water proofing compound conforming to IS-2645 liquid grade as per manufacturer’s instructions with and including polythene film 200 micron over and including 85/25 grade Industrial bitumen (IS-702 : 1988) @ 1.5 kg/sqm blended with the dry sand @ 0.05 cubic meter/ sqm. complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter Complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to coloums complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form tor chajjas complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sides and sofits of beams and lintels complete all as specified and directed.

M&L for Steel Centering and shuttering including strutting, propping etc. and removal of form to sofits of slab complete all as specified and directed.

M&L for use and waste of fair finish formwork for side of slab exc 10cm but n.exc 20cm thick complete all as specified and directed.

M&L Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild steel TMT bars 5mm dia and over as instirrups , cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Mild steel TMT bars 6mm to 8mm dia cut to length, bent to shape required, including cranking, bending pirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F rolled mild steel in plates channel (plain or chequred) square cut or notched (ordinary and counter shunk)forming holes, withpout any attachment of quality FE 410-W (Gde-E-250)quality-B complete all as specified and directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe-410- W(Gde- E-250) quality-B. complete all as specified and directed.

S&F mild steel for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe-410- W(Gde- E-250) quality-B complete all as specified and directed

M&L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Complete all as specified and directed.

M&L for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Mild steel screw bolts having dia of neck exc 5mm but not exc 10 mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified and directed.

S&F0.8mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated of any profile steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified up to anyheight including all necessary scaffolding and safety measures complete all as specified and directed.

M & L for pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified any height Mtr height including all necessary scaffolding and safety measures complete all as specified and directed.

M&L for brick work with fly ash bricks old size, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brick work with fly ash bricks old size, straight or curved on plan to any radius,in half brick walls built in cement mortar 1:4 complete all as specified and directed.

M/L brick work with fly ash bricks old size straight or curved on plan to any radius exc 6m mean radius build in CM 1:4 Complete all as specified and directed.

M&L for Rendering 15 mm thick cement plaster in CM 1:4 on fair faces of brick/concrete surfaces finished fair and even, using water proofing compound admixture (if directed) as per manufacturer's instruction, complete all as specified and directed. Note :- WPC will measuered and paid separatly under relevant item of schedule.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) on walls in cement mortar (1:6), complete all as specified.

M&L for rendering 5mm thick on fair faces of ceiling / chajja concrete surfaces in cement mortar 1:3 complete all as specified & directed.

Supply only intergral water proofing compound (liquid admixture) Complete all as specified and directed.

M&L for grading roof in cement mortar 1:3, 25mm thick in edge and 50mm thick in ridge including necessary curing complete all as specified in SSR Part I clause No 11.42.2

M & L for providing water proofing treatment with a layer of APP based polymeric membrane, 3 mm thick (minimum), weighing not less than 3.60 kg/Sqm reinforced with polymer non woven fabric (weighing not less than 160 gm/ Sqm) shall be applied over one coat of cold bituminious primer @ 0.40 ltr/ Sqm ( membrane shall be laid using butane torch and sealing all joints etc, complete all as specified and directed .( Note: The overlaps shall be of minimum 75 mm on longitudinal direction and 100 mm on transverse direction) complete all as specified and directed.

M&L one coat of aluminium paint over APP membrane complete all as specified and directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing Complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet trip of 20mm with stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing Complete all as specified and directed.

S&F steel windows with side hung shutters including projection type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as directed by Engr-in-Charge.

S&F steel ventilator with top hung shutter (minimum wt of steel section should be 1.42kg/m including hinges, steel peg stay) complete with glazing bars, dovetailed or welded, including taking down existing unserviceable one including making good disturbed surfaces as per exising specifications complete all as specified and directed.

S&F Sheet glass, 4,0mm thick pin headed quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed.

3mm thick figured glass, pin headed type and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as specified and directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel complete all as specified and directed.

S&F aluminium anodised 150 mm barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm long aluminium alloy handles,fabricated type, anodised complete all as specified and directed.

M&L for 150mm thick PCC 1:1.5:3 nominal mix concrete with using 20mm graded stone aggregate as in path/hardstanding/paving etc with broom finished laid in alternate panel of size as directed by Engr-in Charge.

M&L 100mm thick PCC 1:4:8 type D2 using 40mm graded crushed stone aggregate as in hardstanding laid in panels with and including use and waste of formwork and to divide the area in panels and finishing the surface even and fair complete all as specified and directed.

M&Lfor 75 mm thick, Cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate), as in sub base complete all as specified and directed.

M&L cement concrete type B0 (1:2:4) using 12.5 mm graded aggregate 40 mm thick as in floor for receiving screed bed of floor tiling complete all as specified and directed.

M&L for 75 mm thick cement concrete M10 (Nominal Mix) with 40mm graded crushed aggregate finished even and fair laid to a slope of 1 in 12, laid in alternate bays, each bay not exceeding 3 m length with joint filled with bituminous mastic filling comprising a mixture of 1 part of heated Industrial bitumen 85/25 grade and two parts of heated sand as in plinth protection Complete all as specified and directed.

M&L for glazed ceramic colour joint free tiles tiles in verticle surface 350x250x7mm thick set and jointed in neat cement slurry over 10 mm thick 1:4 cement mortar plaster and pointed in coloured cement to match complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11 sqm in floors laid over 15mm thick 1:6 cement mortar screed bed etc. set and jointed in neat cement slurry and pointed in white of coloured cement to match complete all as specified and directed.

M&L Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 20mm thick screed bed in cement mortar 1:6 complete all as specified.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L for Forming 20mm thick Expansion joints for 150mm thick concrete pavement filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘B’ complete all as specified and directed.

M&L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'B' all as specified and directed.

M&L for Forming Construction joint 150mm deep x 10mm wide (Grade B) filled with sealing compound Group 'B' complete all as specified and directed.

Material & labour preparation of newly plastered surfaces of wall & applying Two coas of cement based paint over a coat of alkali resistant primer over new surfaces complete all as specified and directed.

M/L Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including Preparation of new plastered surfaces complete all as specified and directed.

M&L for prepartion of newly plastered ceiling surfaces and applying three coat of white wash complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on newly steel surfaces of any description over 10cm in width or girth not otherwise described incl preparation of surfaces and as all specified complete all as specified and directed.

S&F Stop valves 15mm dia CP fency type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F PVC (SWR) 110mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

M&L for steel tubes,15mm dia bore 'medium grade' with all fitting; laid in wall and ceiling complete all as specified and directed.

M&L for PVC (SWR) floor trap 75mm dia, plain with grating including jointing with solvent cement etc complete all as specified and directed.

S&F vitreous China wash basin white, flat back,size 580X450 mm including cutting for pinning in ends of brackets,complete all as specified and directed.

S&F 15mm bore pillar taps cast copper alloy,with capstan heads,chromium plated,screwed down, fancy type high pressure, with or without lettred 'HOT orCOLD' with long screwed sunk and fly nuts complete all as specified and directed.

S&F Vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe) including urinal spreader of PTMT any colour for fixing with 15mm dia pipe. (Minimum weight 60gms) and including waste pipe complete all as specified and directed.

S&F CP Bib taps 15mm dia, with cfancy handle, screwed down, screwed for iron pipe or for brass ferrule, fency type and fixed complete all as specified and directed.

S&F vitreous China squatting pan, ' Orissa patteren, size 580 x 440 mm white, with integral footrests and PVC (SWR) S or P traps (excluding flushing cisteren and flush pipe) complete all as specified and directed.

S&F wash down water closet (pedestal pattern) complete white with plastic water closet seat black closed pattern with flat bottom anc cover and mild steel chromium plated or aluminised hinging device and flush pipe of polythelene of low or density or PVC 32mm dia for low level flushing cistern complete all as specified and directed.

S&F 10 litre capacity two way flash PVC low level flushing cistern with all accessories complete fixed with WC including syphone pipe, PVC flushing pipe of size complete all as specified and directed.

S&F chromiuim plated Swivel shower roses with shower arm, 125 mm size including fxing to steel pipe or union etc complete all as specified and as directed.

S&F PVC connection pipe 15mm size & 600mm long with cromium plated brass coupling on both ends suitable for 15mm bore steel tubing complete all as specified and directed.

M&L for PCC 1:3:6 type C2 Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested; in

S&F e drainage sewer system pipe bearing 160mm dia minimun 4mm thick including jointing with coupler, bend, tee as per site requirement complete laid in trenches or floors complete all as specified and as directed Note: PCC haunching will be measured and paid seperately

M&L for 10 Users On site LLDPE septic tank designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, Vent shaft, connection etc., complete for, complete all as specified and directed.(2000Ltr)

M & L for concealed point wiring for fan/light point controlled by one one way switch complete with 1.5 sq mm FRLSH,PVC insulated multi stranded copper conductor single core cable 1100 volts grade (Red/yellow/blue wires for phases and black wire for neutral),drawn into and including non metalic PVC rigid conduit medium grade of suitable size and conduit accessories fixed on wall, floor, roof etc. and including PVC FRLSH insulated 1.5 sq mm copper conductor for earth continuity (Green Colour) and connected to common earth dolly including sunken in GI terminal box 2.8 mm thick bakelite hylam sheet cover, ISI marked with CM/L no. for mounting switch & sockets ect. Note : a) Note :- Cost of PVC conduit, cutting chases of wal/ceilingl, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

All as per item No. 94.00 here-in-before but 5 Amp socket on same board with other switches.

All as per item No 94.00 here-in-before but using 4.0 sqmm FRLSH PVC insulated unsheathed multi strand copper cable (1100 V) for line conductor and 4.0 Sqmm FRLSH PVC insulated unsheathed solid copper cable (1100 Volts) for earth continuty wire for one 15/16 amp multi socket out let on independent board.

Supply and fix switch piano flush type, single pole, 5/6 Amps, one way complete all as specified.

S&F socket outlets 2 in 1, 5 pin, 5/6 Amps flush type 230/240 V complete all as specified and as directed .( For Same Board only)

Supply and fixed switch socket combination 5 in 1 , 6 pin , (5/16 Amps ) flush type controlled by one switch complete all as specified.

Supply & fix ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified.

Supply and fixing lamp holder, PVC/polycarbomate type with back plate straight of angle suitable for LED lamp complete all as specified and directed.

Supply and fixing for concealed type sub main wiring with two run of 6.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor (Red/yellow/blue wires for phases and black wire for neutral) drawn in and including through Rigid non-metallic PVC conduit(medium) ISI marked of size 25mm bore with all fittings like tee/Bend/Elbow/Reducer/Bell mouth/Junction / Terminal Boxes etc. and fixing accessories such as coupler, lock nuts, saddles, pipe hook etc. including one run of 6.00 Sqmm single core PVC FRLSH PVC insulated unsheathed stranded copper conductor as earth wire (green in colour) complete all as specified. Note : (i) Note : 2 runs of line conductor, one run of earth continuity conductor, one run of PVC conduit shall be measured as unit length. (ii) Cost of PVC conduit, conductors, making good disturbed wall surfaces including finishing with cement mortor 1:4, matching with existing colour/paint of surface are deemed to be included in the quoted rate.

Supply & fixing LED security light 35/36 watt (Min) 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with BIS approved driver and lamp, Aluminum die cast housing High efficiency long life LED package in integral module with lumen efficacy of 115 lm/W (Min) and viewing angle of 45 degree to ensure better uniformity, electronic LED driver (SMPS based constant current supply) with Output Short-circuit protection, Surge protection & other reliability test as per latest IS. operational voltage of 170 volts to 270 volts, frequency of 50 Hz, protection grade IP 66, IK-08 CRI greater than or equal to 70% , CW available CCT of 5700K/6500K, power factor of minimum 0.95 , life span of minimum 50000 working hours cincluding necessary electrical connections by PVC sheathed copper conductor wire of 3 core x 1.5 Sqmm and necessary fixing arrangement all as specified. Note : (i) The minimum requirement of lumen efficiency, lumen output and power consumption has been specified. However, as per availability, the bidders may opted higher specification with out any extra cost. The quoted rate is deem to be included for that and no extra payment will be made on this account. (ii) The fittings should be marked 'Date of installation" and "Date of Procurement" with marker pen

S&F LED 20 Watt tube light fitting intregated type, including LED retrofit tube lamp 20 W , LED tube light nominal power 20 Watt, LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 110 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 life span of minimum 50000 working hours and LED batten with aluminium housing and polycarbonate diffuser complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting complete all as specified & directed. . Note (i) Make of batten and LED tube lamp should be of same make.

S&F LED 9/10 Watt tube light fitting mirror intregated type, including LED retrofit tube lamp 9/10 W , LED tube light nominal power 9/10 Watt, L LED wattage of minimum 1 watt each and Maximum 3 watt each, operational voltage of 170 volts to 270 volts, frequency of 50 Hz, , lumen efficacy of minimum 115 lumens per watt, , integrated electronic driver (SMP based constant current supply) with output short circuit protection and surge protection upto 2.5 KV, protection grade IP 20, CRI greater than 80%, bema angle of 120 clear, THD below or less than 20%, CW available CCT of 6500K, power factor of minimum 0.95 extruded aluminium LED battens life span of minimum 50000 working hours complete fitting including connecting with PVC insulated multistranded copper flexible cable 1.0 sqmm three core, and PVC round/ square box white colour x 2 Nos for mounting of fitting including taking down old unserviceable complete all as specified & directed. Note : Make of batten and LED tube lamp should be of same make.

Supply and fixing ventilating metalic body exhaust fan heavy duty 300 mm sweep 230 volt AC, complete with louver and all accessories including cutting hole of suitable size, complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor of suitable size all as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC).

Supply and fixing electric water heater(Geyser) vertical type 25 ltrs capacity BEE 5 star rated with inner tank connecting with water tank/supply point sockets and making good in disturbed surface with existing wall/ surface complete all as specified & directed.

S & F sheet metal enclosure for MCB, DB, SPN, 240 Volts, 100 Amps rated busbar, Confirming to IS as per IEC 61439-3, 4 way Double door enclosure made up of CRCA sheet steel, RAL 9003 powder coated, IP 43, Ik09 including fixing the DB box flush in wall of any type and making good the distrubed surface to match as the existing with all as specified and directed .

Supply and fixed MCB SPN 32 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

Supply and fixed MCB SPN 40 to 63 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

Supply and fixed MCB SP 6-32 Amps, 'C' curve 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

Material and labour for earthing complete with Galvanised steel earth plate electrode 600x600x6 mm mm buried directly in ground (Earth pit not less than 2.25m below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to GI wire 4 mm as earth lead by means of bolt, nuts, check nuts and washers of galvanised iron or steel, upto 7.5m length, earth strip protected by and including 15 mm dia GI pipe (light grade) and connected to main test point or body of pole/pannel or lightening arrester of main controlling switch as directed including concrete pit in PCC (1:3:6) type C1 , Precast RCC (1:2:4) Type B1 cover slab of size 54x54x5 cm reinforced with 8 mm dia TMT bars @ 100 mm C/C both ways with one handle for lifting made out of 10 mm dia TMT bar embedded in precast cover slab, funnel, wire mesh, 20 mm bore GI Pipe (Medium Grade) for watering, Charcoal and salt in alternate layers of 15 cm (Compacted Thickness) around the earth electrode including necessary excavation, earth work in any type of soil and disposal of spoil to a distance n.exc 50 m and necessary testing complete all as shown in Electrical Plate No 3 of SSR Part-I. NOTE : 1. The unit rare includes for protectionh GI pipe of 40mm and watering pipe of 20mm bore including excavation for earth pit in any type of soil/disintegrate rock. 2. Contractor has to bring agriculture soil from outside of defence land and fill in earth pit to acheive desired result as the soil resisitivity is very high. 3. The cost of GI wire of 32x6mm including protection pipe, from top of earth plate upto 7.5 meter above/below ground level is deemed to be included in the unit rate. 4. All the joints in GI strip and connectgion with earth plate to be welded through brazing and in addition by providing double brass nut bolt and washer. 5.Costing of welding and nut bolts are deemed to be included in the unit rate

Supply, Laying, testing and connecting XLPE sheathed,PVC insulated screened PVC bedded,galvanised steel strip of wire armoured electric power cable heavy duty with solid aluminium conductor 1100 volt grade of size 2 core 6 sqmm. , laid in trenches/surface of wall/in GI pipe along with pole for connection to OH lines,including Brass Compression Cable Gland, Terminal Lugs,clamps,nut & bolts etc all as specified.

Materials and labour for sand filling around the cable with approved quality coarse sand for sand cushioning of Under ground cable including spreading and punning down to 18 cm thickness complete all as specified and as directed. (Compacted thickness shall be measured)

Supply and lay in trenches fly ash bricks, for cable protection all as specified and directed by the Engr-in-Charge.

Supply and fixing steel tubing light grade 50 mm dia including all fittings, laid across road in trenches, or across PCC drain, along electric pole or floor / wall for cable protection complete all as specified and as directed.

S&F Pipes galvanized, 25 mm bore “Medium grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement or specified.

Supply& fixed gun metal , gate valve, 25 mm dia with iron wheel head, screwed both ends for iron pipe and fix complete all as specified and directed.

S & F rotational moulded polyethylene ISI marked (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position with and including Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for 25mm bore dia iron pipe, provision of 25 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes including dismantling the existing one and removing to store complete all as specified and as directed.

BHARAT CONSTRUCTION (BID ID -3422291)

MS ROYAL CONSTRUCTION INDEX NO 158 2010 BKP (BID ID -3422269)