CERTAIN REPAIR TO OFFICERS MESS AND SINGLE LIVING OFFICER ACCN AREA UNDER AGE BR-II AT NAMS

Amount

Taking down cement plaster on brick/stone/concrete walls /ceiling incl racking out joints etc,hacking for key, scrubing down with water etc & dispose off debris upto a distance n exc. 500 mtrs where directed complete all as specified and directed.

M&L for 15mm thick cement plaster in Cement motar1:4 on fair faces of brick or concrete work and finishing the surface even and fair (without using extra cement) incl WPC @3% weight of cement etc. complete all as specified and directed. Note-WPC will be measured and paid separately under appropriate items

M&L for rendering 15mm thick in cement mortar (1:6) on other than fair faces of brick work or concrete surfaces of walls , finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick cement plaster in CM (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth (without using extra cement) etc complete all as specified and directed.

Dismantling of brick works in cement mortar complete all as specified and directed.

M & L for brick work with sub class 'B' bricks in Cement motar (1:6) straight or curved on plan exc 6 mtrs mean radius, complete all as specified and directed.

All as per Srl item No 6.00 above but except bricks (old dismantled serviceable bricks obtained from Srl item No 5.00 shall be reused after necessary cleaning of mortar)

M&L for half brick work with sub class ‘B’ bricks (old size brick) straight or curved on plan to any radius in half bricks thick walls built in CM 1:4 complete all as specified and directed.

M&L for wall care putty of 1mm thickness over plastered/Unplastered surface to prepare the surface even and smooth complete all as specified and directed. Note: Entire spalashes in floor shall be cleaned immediately after completion of periodical services.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper complete all as specified and directed.

M&L for preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

M&L for applying two coat of cement base paint over a coat of alkali resistant primer including preparation of newly plasterd or previously untreated surfaces of walls, pillars cornces etc complete all as specified and directed.

M&L for applying one coat of cement base paint on walls, pillars cornices etc surface incl preparation of old plastered/painted surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss incl filling holes necessary where required with putty as in pathces or nail holes to obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed. complete all as specified and directed.

M&L for applying one coat of oil bound distemper on walls, pillars cornices etc surface incl preparation of old plastered/painted surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss incl filling holes necessary where required with putty as in pathces or nail holes to obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed. complete all as specified and directed.

M&L for Prepration of old surfaces of ceiling includinng scrapping down smoke ,soot,and efflorescence salts and treading oil and gresy spots, brooming down or steel wire brushing removing nails making good holes cracks etc on old plastered/painted surfaces and applying one coat of white wash on ceiling surface incl filling holes necessary where required with putty as in pathces or nail holes to obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed.

M&L for applying one coat of Acrylic smooth exterior emulsion paint on walls, pillars cornices etc surface incl preparation of old plastered/painted surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and incl filling holes necessary where required with putty as in pathces or nail holes to obtain smooth finish using sand paper and matching the existing surface complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint (Ordinary tint) over a coat of Pink primer.

M&L for applying one coat of synthetic enamel paint on wooden surface of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on steel surface of any description over 10cm width or girth including preparation of old surfaces complete all as specified and directed.

Taking down Chowkats or frames from the opening of size not exceeding 1.5 sqm each with shutters ( without taking off shutters from the frames) complete all as specified and directed

Taking down Chowkats or frames from the opening of size exceeding 1.5 but n exc 4 sqm sqm each with shutters ( without taking off shutters from the frames) complete all as specified and directed

Taking down Shutters of any description of size exceeding 1 sqm and not exceeding 2 sqm each complete all as specified and directed

Taking down Shutters of any description of size exceeding 1 sqm and not exceeding 2 sqm each complete and refixing in the same opening after easing and adjustment all as specified and directed

Taking down aluminium door and refixing in same opening after repairing to damaged/loosened rail sections, tightening of screws, repairing/replacement of rubber packing to aluminium shutter, repairing/oiling to locking arrangement and oiling/greasing, repairing to handle, tower bolt as required and making the shutter smooth as in MAP Accn complete all as specified and directed.

M&L for framed work as in doors of angle or other section complete drilled for fixing sheeting with all fitting and fixture complete all as specified and directed.

S&F PVC door frame size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinf with MS square tube supplying & fixing in opening as per specificationn make Rajshree complete all as specified and directed.

M&L for Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame ( single rebated)of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass including fixture and fittings like as Stopper, Cleat, Pintal hinges, holdfast etc all as shown on drg No CEJZ/TD1019/08 sheet 1/3 to 3/3 dt 01 May 2008 complete all as specified. (a)10mm Sq Guard bar 10Cm C/C. (b) One shop coat of red oxide primer and two coats of Synthetic Enamel piant to MS ventilator and guard bar. Note:-(i) Including taking down old steel window and making good dismantled portion with PCC 1:2:4 type B-0 including hold fast PCC (four No’s for Each ventilator) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed by Engineer-in-charge. (ii) sheet glass and wire mesh shall be measured and paid separately)

S&F powder coated aluminium frame for doors ,windows, ventilators with one or more rebates including joining cleats for fixing complete all as specified and directed by Engineer-In-Charge. (Min. thickness of powder coating 50 micron)

S&F aluminium powder coated shutter (for doors) wighing 0.55 kg/m including necessary jointing cleats, glazing clips, rubber beading with neoprene packing anodized handle 2 no in each, locking arrangement(mortised) and aluminuium anodised tower bolt 200 mm long aluminium snap beading screws complete all as specified and directed.

S&F aluminium powder coated shutter (for window and ventilator) side hung type without sash, aluminium section wighing 0.55 kg/m including necessary jointing cleats,glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fitting such as peg stays 150mm long (1 no.) hinges type B-21 100mm long( 2 no) suitable handle (1 no) complete all as specified and directed.

S&F Sheet glass, 5.5mm thick ordinary quality, in squares,exceeding 0.50 sqm in each pane including rubber packing and aluminium beading with and incl solar control film 25 Micron reflective type sticked to glass panes as per instructions of manufacturer complete all as specified and directed

S&F for 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F, 35 mm thick, 2nd class hard wood, glazed & skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc. Sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.24 (a) complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent ement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, all as per manufacturer's instruction complete all as specified and directed.

S&F for 30 mm thick factory made solid WPC (Wood polymer composite) moulded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including S.S wire mesh shall be fixed with 15 x 15 Square tubes in is rails with screwing 8 x 28 mm heat metal zink coated screws can be remove or fix again after changing of wire mesh when needed. The density shall be as per manufactures instructions complete all as specified and directed.

M&L Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of EngineerIn- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ Chowkhat of size 50x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good after complete all as speicifed and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door frames/ chowkhat double rebated of size 65 x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant including making good after complete all as speicifed and directed.

M&L for providing and fixing fully glazed 12mm thick toughened glass as in hinged door, partition automatic doors and similar work including cutting to shape , drilling holes required and taking down & removing broken any type glass piece . (a) Two handles fixed with screws each of 300 mm length and min 20mm dia made off stainless steel. Minimum two stainless steel hinges in each door of grede SS 304 All the samll works such as cuttings raking making holes pinning insertion etc making good to disturbed portion as per site requirements/ users / given by the Engineer-in-Chrage shall be included in unit quoted rates .(b) All itching work in glass as directed Engineer-in-Chrage shall be included in unit quoted rates. (c) All Glass door shall be water tight with megnets water seal/as directed Engineer-in-Chrage shall be included in unit quoted rates.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 3mm thick, sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.5 Sqm in each pane fixed with oil putty or beads complete all as specified and directed.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty in square n. exc 0.5 sqm each panes complete all as specified

S&F in repair for 3mm thick, sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.5 Sqm in each pane fixed with oil putty or beads and incl hacking out glass old complete all as specified and directed.

S & F in repair Aluminium body door closer hydraulically regulated, designation No. 2 universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg. complete all as spd and directed by Engr-in-charge.

S&F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main bodywith stainless steel cover,governing pivot made of brass, other parts made of mild steelheavy duty and fixed

S&F in repair Mortice lock, vertical type, size 100 mm door lock 4 lever baras complete all as specified and directed.

S&F stainelsss steel butt hinges 100mm size fixed to frames any types all as specified and directed by Engr-in-charge.

S&F aluminium handle cast type anoodised 150mm size ISI mark complete all as specified and directed.

S&F aluminium anodised barrel tower bolts 150 mm size of extruded section and fixed ISI marked complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door bolt 250 mm size with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F in repairs 300mm long mild steel ordinary rat tail rod pattern spring with roller plate including fixing with nails/ bolts or welded complete all as specified and directed.

S&F floor doouble door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified and directed.

S&F, in repairs, 20 mm thick, PVC sheet one side prelaminated of approved texture ("Celuca Ply of Rajshree make or equivalent in as approved by GE) as in Kitchen cabinet, shelves, cupboard shutters etc and like incl making with nails, screws etc complete all as specified and directed. (Note:- Each member i.e. shelf, partition & shutter of kitchen cabinet shall be measured and paid separately)

M&L for Gypsum board panel 12 mm thick as in ceiling including T, L & Channel section accessory of galvenised mild steel, GI suspender all as per manufacturer design confirming to IS 2095 and IS 2542 – 1981. Weight of board not less than 7 Kg per Sqm including two coat of Oil bound distemper over a coat of plaster of paris including dismantlinmg down of old ceiling boarding incl framing complete all as specified and directed. Note: - Rate quoted shall be deemed to be inclusive of gypsum board, frame work and suspender.

M&L in repair for PVC hollow wall panelling 7 to 8mm thick any colour/design approved by engr-in-charge, inclusive of fixing on to wall incl moulding end caps fixed with PVC sleeves and screws as required at site complete all as specified and directed.

M&L Double charged/ ultra double charge vetrified tiles 8 mm thick, in (Square/rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match incl dismantling / demolition , coloured tiles laid over and including 15 mm thick screed bed or bedding layer in Cement motar (1:6) complete all as specfied and directed.

M&L for Double charged/ ultra double charge Vitriefied tiles 8 mm thick square/rectangular) polished area of each tiles not exceeding 0.36 sqm as in vertical surfaces such as dados/skirting etc set and jointed in neat cement slury and in coloured cement to match incl dismantling / demolition , Coloured on incl plaster (backing coat) 1:4 Cement motar 10mm thick layer in Cement motar complete all as specfied and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc. laid over 15mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

S&F non skid ceramic coloured tiles as in vertical surface for skirting 7 to 8mm thick (square/rectangular) size of tile exc 0.11 sqm but not exc 0.18 sqm in virtical surface etc set and jointed in neat cement slurry and pointed in vertical surfaces white or coloured pigment to match the shade of tile over and including 10mm thick rendering in CM 1:4 complete all as specified and directed.

M&L Non skid ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 06 sqm but not exceeding 0.11 sqm, in floors etc. laid over 15mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

M&L for Glazed ceramic coloured tiles of size 300mm x 450 mm x 7mm thick verticale tiles with highlighter any colour on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling / demolition and e colour of tiles, incl dismantling / demolition over and including rendering 10mm thick in cement mortar (1:4) , complete all as specified and directed.

M&L for Marble of any shade shade of thickness 18-20 mm thick in slab laid over 15mm thick screed bed in cement mortar 1:6 as in floor, steps, riser & treads and jointed in neat cement slurry and pointed in white or coloured cement to match incl dismantling / demolition and rubbish off the primises and rounding to edges of stone slabs one edge such as in counter type WHB platform etc. to the entire satsfaction of Engineer-in-Charge.. etc complete all as specified and directed. Note-size of slab will be decided by Engr-in-Charge.

M&L for Granite 18-20 mm thick (table rubbed and polished) in steps, treads, risers, jambs, pillars, window cills, cooking platforms, wash basin platform, treads, risers and like laid in cement 15 mm thick cement mortar 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite rounding to edges of granite stone slabs one edge such as in counter type WHB platform etc. incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

M&L for 18-20 mm thick machine cut kota stone slab laid over 15 mm thick screed bed of cm 1:6 as in flooring & riser and jointed with grey cement slurry mixed with pigment to match the shade, rubbing and polishingand incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

M&L for heavy duty, exterior grade (Durastone of Somany/Endura of jhonson or equivalent as approved by GE) of 400 x 400 size 12mm thick, as in floor (in trades, landing etc ), set, jointed and pointed in neat cement slurry with white cement and pigment laid over and including screed bed or bedding layer of 15 mm thick in cement mortar (1:6) incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

S&F in repair for viterous china squating pan of (Orrissa Pattern) size 580 x 440 white with 'P' or 'S' trap front or back inlet and integral foot rest , including joining, filling and provision of cement concrete bedding 1:5:10, type E2 (excluding flushing cisteern and flush pipe) fixed incl cement concrete bedding as required set complete all as specified and directed.

S&F in repair for viterous china wash down water closet pan (pedestal pattern) coloured including 'P' or 'S' trap with flush pipe of chromium plated brass 32 mm dia for low level flushing cistern incl plastic seat cover white closed pattern with float bottom and cover and jet connection and mild steel chrominum plate or aluminized hanging device fixed in repairs complete all as specified and directed.

S & F in rep vitreous china size of 370x545x370mm rimless wall hung WC with UF soft close seat cover hinges accessories set including fixing bolt but excluding flushing cistern and flush pipe

S & F in rep vitreous china floor mounted single piece WC with dual flushing cistern PP soft close seat cover , hinges accessories set as per size 390x610x800mm with istern fitting including fixing bolts flush pipe complete all as specified and directerd

S & F in repair concealed flush valve complete with 32mm size control cock 200mm long operating lever complete all as specified and directed.

S and F single piece slim concealed flushing cistern with wall mounted frame installation kit and S type drain pipe connection set for wall hung WC with flush control plate complete all as specified and directed

S&F in repair Vitreous china ware counter ovel wash hand basin, any colour, size 570 x 450 mm size fixing in slab including fixing waste pipe , CP waste coupling all as specified and approved by Enger-in-Charge

S&F in repair Vitreous China wash hand basin (WHB) white,flat back size 550x400mm including CP waste coupling 32mm bore, incl 32 mm dia PVC waste pipe complete all as specified.

Supply & Fixing in repairs vitreous china urinal half stall type with CP spreader white with grating and union for discharge pipe, including providing and fixing plug, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing with brackets, flush pipe, grating and union for discharge pipe complete all as specified and directed

S&F in repair 10 Ltr capacity PVC valveless symphonic action type flushing cistern white low level with ball valve flote handle including bracket and flush pipe of polythylene of low or high density or PVC,32mm dia complete all as specified and directed Note flush tank can be conceiled in wall if reqd i.e in the case of wall hung type water closet pan.

Supplying , fixing & Hoisting and fixing in position and connecting, in repairs, 500 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I including 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

Supplying , fixing & Hoisting and fixing in position and connecting, in repairs, 1000 litres capacity rotational moulded polyethylene water storage tank (cylindrical, vertical with closed top) including fixing arrangement for inlet/outlet/over flow and vent pipe of standard size all as specified in SSR Part-I 20mm bore, ball valves high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

Taking up or down 15mm dia steel tubing and connections incl cleaning for refixing or removal to store all as specified and directed.

S&F 15mm dia GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floors all as specified and directed.

Fixing only all as per sr item No 81.00 above but except pipe Note - Serviceable pipe obtained from ser item No 80.00 shall be used after necessary cleaning

Taking up or down 20mm dia steel tubing and connections incl cleaning for refixing or removal to store complete all as specified and directed.

S&F 20mm dia GI tubes medium grade with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Fixing only all as per ser item No 84.00 above but except pipe Note - Serviceable pipe obtained from ser item No 83.00 shall be used after necessary cleaning complete all as specified and directed.

S&F in repair 15 bore dia chromium plated Stop cock/Angle cock screwed down high pressure with crutch or butterfly handle & screw both end for iron pipe or for unions complete all as specified and directed.

S/F in repair 20mm bore stop cock cast copper alloy CP screwed down high pressure with crutch or butterfly handle complete all as specified and directed. .

S&F in repair of brass cromium plated fancy type bib taps 15 mm bore long nose screwed down screwed for iron pipe or for brass complete all as specified and directed

S&F for in repair 15mm dia swan neck pillar cock chromium plated fancy type screw with iron pipe incl all fittings complete all as specified and directed.

S&F in repair 15mm bore Stop valves, cast copper alloy, screwed down , high pressure, with crutch or butterfly handles , screwed both ends for iron pipe or for unions, fancy type, chromium plated with long shank and cup ( concealed type) and fixed.

Supplying and fixing in repairs swan neck 15mm bore centre hole wash basin mixer cast copper alloy chromium plated screwed down high pressure screwed for iron pipe complete of approved make as per sample all as specified and directed

Supplying and fixing in repairs cast copper alloy chromium plated wall mixer 3-in-1 system with complete provision and fixing for Overhead Shower with 115 mm Long Bend pipe, CP screwed down high pressure with long screwed both ends for 15mm dia bore GI pipe complete of approved make as per sample all as specified and directed.

S&F in repairs 125mm brass CP shower rose fancy type with CP arm complete all as specified and directed.

S&F overhead shower 150mm x 150mm square shape single flow brass chrome plated with gray face plate ) incl shower arm 190mm long with rubit cleaning system complete including taking down any type shower all as spd and directed.

Supply and fix toilet paper holder with flat recessed type stainless steel complete all as specified and directed

Supply and fixing Health faucet (ABS body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metr long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified.

Supply and fix in repair CP flushing jet including 15mm bore 450mm long PVC pipe connection for Europian type closet of suitable length with brass check nut complete all specified and directed

Supply and fix sheet glass shelf assembly consisting of 5.50mm thick sheet glass shelf 12cm wide with cromium plated bracket guard and and railing 60cm long including taking down old broken glass shelf, if available, complete all as specified.

S&F, glass corner minimum size 300mmx300mm minimum 5.50mm thick with cromium plated bracket guard and and railing including taking down old broken glass, complete all as specified and directed.

Supply and fixing in repair PVC waste pipe 32/38/40mm dia, 600 to 750mm long complete all as specified.

S&F PVC connection 15mm size with PTMT nuts of length 450mm.complete all as specified

Supply and fix stainless steel soap dish of min size 120mmx 100mm including taking any old pvc/steel broken tray complete all as specified.

S and F in repair brass chromium plated tubular towel rail D type 60cm long between flanges including bracket complete all as specified

S&F curtain rod 25mm bore of 1mm wall thickness made off stainless steel fancy type decorativewith decorative ball type side brackets and knobs including taking down old any type curtain rod complete all as specified and directed.

S&F in repair sinks with drainage board made of 1mm thick stainless steel sheet for kitchen or laboratory with plugs, washers,wastes coupling,waste pipe including bedding in cement mortar on to wall or including fixing cantilever brackets or chase cut and fixing the sides as required as per site complete with overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified and directed.

Taking down eaves gutters and rain water pipes ( any size or pattern) , including all fittings , heads, shoes, bends, swan necks, etc., ( measured overall as fixed along the centre line over fittings and accessories

S&F 75mm bore PVC(SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floor complete all as specified and directed.

S&F 110mm bore PVC(SWR) pipes single socketed in any length fixed to walls with dash true nut and bolt at every 2mtr length including all fittings complete all as specified and directed

S&F 110mm bore PVC (SWR) bends any radius Withiout access door complete all as specified and directed.

S&F 75mm bore PVC (SWR) bends any radius Without access door complete all as specified and directed.

S&F 110 mm bore( SWR) vent cowl complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single/double, (single/double T), equal or unequal door complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single/double, (single/double T), equal or unequal complete all as specified and directed.

M&L 75mm bore PVC (SWR) floor trap ,plain with CP grating including jointing with solvent cement complete all as specified and directed.

M&L for PCC (1:5:10) type D-2 using 40 mm graded stone aggregate as in filling in sunken floors including demolition of cement in concrete (unreinforced) of any description and in any position complete all as specified and directed.

Material and labour for Water proofing treatment to sunken floors of kitchen, toilets, laboratories, bath and WC's etc shall be as under :- (a) Application of Two component Acrylic modified cementitious coating (i) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance, existing coatings and achieve a gripping profile that is clean, dry and free from laitance and any other form of surface contamination. The installation instructions in manufacturer’s published literature should be strictly complied with, including but not limited to the following :- (ii) Chipping out any visible cracks in “V-Groove” pattern as applicable. Special attention on this part. Cleaning of cracks & then filling those cracks with SIKA latex SBR 100 putty/ Dr Fixit 302 SBR latex / Perma latex SBR / FOSROC Nitabond SBR latex / Asian Paints latex as required. Final cleaning of surface with power grinder, wire brush, hair brush & vacuum pressure if required. (iii) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO. (iv) Whilst the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions.

(v) Apply Glass Fabric Sheet of Sika Fab 1 / FOSROC/ Dr Fixit/ STP whilst the first coat is wet. (vi) Once touch dry, apply second coat of Acrylic modified Cementitious coating of Sika Top Seal – 107 / Brush Bond FOSROC/ Dr Fixit/ STP/CICO of viscosity as per manufacturer’s instructions on the entire area. (vii) Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (viii) The waterproofing coating should be taken to a height minimum 300 mm above the finished floor level on the vertical surface. (ix) It is essential to cure Acrylic modified Cementitious coating immediately after application (minimum 6-8 Hrs drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking. (x) A protection plaster (12-15mm thick) in CM 1:3 admixed with appropriate Integral water proofing compound has to be applied on the walls. Admixture : Sika Plastocrete Plus / FOSROC / Dr Fixit / STP / CICO confirming to IS 2645. Providing and applying a protection screed of 50mm thick 1:4, cement sand mortar admixed with Sika Plastocrete over the applied water proofing coating on horizontal surfaces. Admixture : Sika Plastocrete Plus / FOSROC / Dr Fixit / STP / CICO confirming to IS 2645

(xi) All the corners and joints should be pre-treated with an elastic waterproofing sealing tape with a Woven bonding mesh on each surface and an elastic expansions zone in the centre of Make Sika Seal Tape S/FOSROC/Dr Fixit/STP. (xii) The membrane has to be protected in accordance with the manufacturer’s recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer’s recommendations (xiii) Waterproofing treatment has to be carried out through applicators authorised (b) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (c) Al CI traps in sunken slabs to be enclosed with PCC 1:1.5:3 (min 15cm) All-round. (d) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40mm stone aggregate) complete all as specified (e) Providing drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed. (f) Providing 25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded stone aggregate as in flooring for laying floor finish all as specified. Note: Items No 118.02 (d), (e) & (f) shall be measured and paid separately.

S&F drainage spout pipe GI 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long) including cutting to existing wall and making good the disturbed surface complete all as specified and directed.

Dismantling brick tiles or terracing single layer as in roofing complete all as specified and directed.

Demolition of mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) complete all as specified and directed.

M & L for 50mm avarage thickness PCC 1:2:4 type B1 (using 20 mm graded stone aggregate as roof padding finishing even and fair without using extra cement for further treatment complete all as specified and directed.

M&L for preparation of roof surface & applying evenly a tack coat of industrial bitumen primer 85/25 grade @ 1.2 Kg/Sqm including APP based polymeric membrane minimum weighing 3 kg/sqm and minimum 3 mm thick reinforced wih polyster non wove fabric (wt not less than 150 gms/sqm) applied on primed surface by forced application of heat and roller, joints to be touched hot and width of overlaps not be less than 150 mm complete all as specified and directed.

M&L, 40 mm thick brick tiles laid over 15mm thick cement motar (1:6) and joints grouted flush in cement Motar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and directed.

ditto - above -124.00 but except bricks tiles complete all as specified and directed.

M&L for providing 20mm thick bedding layer of cement morter (1:3) finished even and smooth without using extra cement and mixed with water proofing compound as per manufacturer's instruction all as specified and as directed. Note :- Supply only Water proofing compound shall be measured and paid separately.

M & L for applying two coat of undiluted thick coat of acrlic reinforcement liquid applied elastorneric water proofing membrane with UV resistance properties and solar refective properties over one coat of primer (1:3, Dilution:water) Note: Every each coat gap between 6 hrs) complete all as specified and directed. Make : The process of acrlic reinforcemnet used by the aplicator Asian paint, Sika, Fosroc

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F mild steel Gde Fe-410-W Gde E-250 quality A as in roof trusses, (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee,angle,channel or flat sections) including distance pieces , cleats etc complete all as specified and directed.

Dismantling Asbestos cement (corrugated or semi corrugated) sheeting in roof coverig complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-1 (using 20mm graded stone aggregate as in plinth protection/path without using extra cement,laid in panels including necessary formwork,inishing even and fair complete all as directed.

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete including dismantiling PCC complete all as specified and directed.

M&L Machine pressed coloured chequered tiles of size 300 x 300 x 25 mm thick laid over 15 mm thick screed bed in CM 1:6 bedded and jointed in neat cement slurry incl dismantling / demolition and rubbish off the primises etc complete all as specified and directed.

S&F Machine pressed coloured precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade over 25mm thick sand cushioning and joint filled with dry sand mortar 1:4, incl dismantling of stone slab and tiles of any description of thickness in floors/aprons etc complete all as spd and directed.

Demolition of reinforced cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas complete all as specified and directed.

M&L for reinforced Cement concrete 1:2:4 type B-0 (using 12.50mm graded stone aggregates) as in Shelves complite all as specified and directed.

S&F mild steel TMT bars 10 mm dia and over., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire ( annealed) not less than 0.90 mm dia. Or securing with clips complete all as specified and directed

M & L of form work to rough finished flat surfaces of suspended slabs such as roof slab, floor slab, landing and similar work not exceeding 200mm thick (horizontal or sloping) complete all as specifird

Material and labour for repairing of RCC projection, chajjas, facia,bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion of RCC at any height and in any situation floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of weight 3 kg/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of painting as existing in building to match with the existing surfaces complete all as specified and directed.note flate area will be measured for thickness upto 200mm and four storey height

M & L Providing precast cement concrete louvres and jallies 35mm thick type B-0 1:2:4 (12.5mm gradded aggregate) set in CM 1:4 ( measured solids ) including all mouldings but excluding frame (precast frame shall be measured separately and for paid under SSR item 04032

M & L Providing precast ce ment concrete (incl reinforcement bar) type B-1 1:2:4 (20mm gradded aggregate) RCC jalli pillar of size 100mmx100mm & 750mm long set in CM 1:4 in setting in mortar including taking down old pillar complete all as specified and directed

S&F in repair CP grating 125mm dia circular of approved make and fixing with cement mortar 1:3 complete all as specified and directed.

Supply only, integral water proofing compound complete all as specified and directed.

Material and labour for damproofing to wall with two component Acrylic polymer cementitious water proof elastomeric coating foor grade mix to form uniform slurry and apply with paint brush as first coat then laying a layer of fibre glass mesh cloth as first coat is still green with overlap of joints of fibre mesh not less than 100 mm, then finally apply second layer mix by brush to entire surface of container covering 0.6 - 0.75 Sqm /Kg at 1 mm thickness in two coat depending on the level of substrate and curing it for minimum 3 days. Note : Quoted rate shall be deemed to be inclusive of materials all labours, tools and plants, scaffolding and working upto height 6 metre etc. Make : Pidilite Industries Ltd/ Fosroc India Ltd/ IWL India Ltd, BASF/T-Guard ANTC of Make - Trermax, complete all as specified and directed.

M/s MAHAJAN CONSTRUCTION CO. (BID ID -3307529)

tarlok singh contractor (BID ID -3306999)

Santokh Singh and Associates (BID ID -3307272)