Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | 1₹26.5 CrAccepted-AOC | ₹26.5 Cr Quoted ₹26.8 Cr | 1 | Accepted-AOC BID IS LOW |
| 2 | 2₹27.5 CrRejected-Finance C 2488 SUSHANT LOK PHASE 1 GURGAON 122001 HARYANA | GURUGRAM | HARYANA | 122001 | ₹27.5 Cr | 2 | Rejected-Finance BID IS NOT LOWEST |
| 3 | 3₹28.5 CrRejected-Finance | ₹28.5 Cr | 3 | Rejected-Finance BID IS LOWEST NOT |
Tender Value
₹25.9 Cr
EMD Value
₹25.9 L
Closing Date
25 Jan 2024, 5:00 pmClosed
Chief Officer
Municipal Council Pandharpur
Nam SankirtanSabhagruha Auditorium Phase Two for Pandharpur Municipal Council at Reservation No53 Pandharpur
2024_DMA_979297_1
PMC/CIVIL/JAN-2024
Open Tender
Civil Works - Others
548 days
Pandharpur
Please refer Tender documents.
3 documents required · 3 mandatory
₹10,000
₹25.9 L
Municipal Council Pandharpur
20 Jun 2024
5 Jan 2024
29 Jan 2024
5 Jan 2024
25 Jan 2024
5 Jan 2024
5 Jan 2024 - 25 Jan 2024
22 Jan 2024
Amount
EXCAVATION, FILLING AND SOLING
Excavation for foundation in earths, soils of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 metres beyond the building area & stacking and spreading as directed, dewatering , preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting, etc. complete.(Lift upto 1.5m) By Mechanical Means spec. No. Bd.A.1 page No. 259
Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting complete. Spec. No.: Bd.A. 12 Page No. 264
Filling in plinth and floors with contractors soil sand or murum in 15 cm to 20cm, layers including watering and compaction complete.
Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 percent of Clorophysiphas/ 20 E.C. Hephoclore at the rate of 7.5 litres emulsion concentrate per hole and sealing the same with proper filling & covering 10 years guarantee. Spec : As directed by Engineer In Charge
CEMENT CONCRETE ( PLAIN & REINFORCED)
Providing and laying in situ, cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, compacting and curing complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer With crushed sand. Spec. No.: Bd. E. 1 Page No. 287
Providing and laying Cast in situ/Ready Mix cement concrete in M20 of trap/ granite/quartzite/gneiss metal for steps including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite/quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, Steel centering, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.
MASONRY WORK ( BRICK )
Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, racking out joints, watering and scaffolding Complete. Spec.No.:Bd.G.5PageNo.315
Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of 2 bars of 6 mm diameter / 2 hoop iron strips 25 mm X 1.6 mm placed at every third course, properly bent and bonded at ends scaffolding, racking out joints and watering etc. complete
STONE WORK
NEWASA STONE WORK
Providing & fixing Newasa stone Ashlar / sadguru ghadai masonary in of 50 mm thk in size & 275 x175 in cement morar 1:3 for composite masonary. Install stone member in plumb level & in aligment provide through stone at interval & necessary accessaoris like clips , bars,clamps or necessary are required for errction & stone masanary to supporting back brick wall & back up material. Use pigment in mortor for grouting of colour match to natural stone, watering & cleaning etc complete as per as directed by Engineer in charge .
DHOLPUR STONE
Providing & fixing Dome kalash of different sizes in Dholpur stone as per detail design on top of curved surfaces etc complete.as per as directed by Engineer in charge .)
Small size
Providing & fixing cladding to vertical surfaces in Dholpur Stone of 50 mm thk in size of 275 x175 mm as per design & detials shown in drwaings in cement mortor 1:3 with necessary accessaries ,fixture & adhesive of recommanded brands for fixing to supporting back surface with watering etc. complete.Use pigment in mortor for grouting og colour match no natural stone watering etc complete as per as directed by Engineer in charge .)
RED AGRA STONE
Providing & fixing 20 MM THK Red-agra Stone cladding for sloping chajja on m.s. frame structure as per details & drwings in 1:3 morter/adhesive for joints & also on R.C.C surfaces as per directed by Engineer in charge .)
Providing & fixing Full round bands of 100 thk in Red Agra stone as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .)
Providing & fixing brackets in Red Agra of 100 mm thk of various sizes as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .)
Big size
Providing & fixing Arches of various sizes in 150 mm thk Red agra as per design a details drawings in 1:3 cement mortor with necessary accessaries & adhesive for fixing & erection ..Use pigment in mortor for grouting og colour match no natural stone watering etc complete as per as directed by Engineer in charge .)
GFRC & PRECAST WORK GFRC
Providing & fixing kalash Petal design in GFRC as per the detail drawings & sizes with high density concrete made from Portland cement, crushed stone, & polymers reinforced with continuous filament glass fiber mat & structural reinforcing as required. Color to match architect’s sample.As per directed by Engineer in charge .)
PLASTERING AND FINISHING
Providing internal cement plaster 12mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing complete. Spec. No.: Bd. L.2 Page No. 368
Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. Spec. No.: Bd.L.7 Page No. 369
Providing and fixing chicken mesh jali (24 gauge) at the junction of 2 different surfaces of different material component at the time of plastering to prevent cracking in plaster surface as and where directed at all floors with all leads and lifts etc. complete. Spec. No.: As directed by Engineer in Charge:
Providing and applying gypsum plaster ( with Gypsum material of Gypsum India / Mega Sign or equivalent make ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete.** Spec. No.: As directed by Engineer in charge.
WATER PROOFING WORK
Waterproofing Treatment to new terrace by using Polymeric Cementitious Membrane as approved by Engineer incharge, followed by 112 mm thick brick bat coba covered with 20mm mortar finish. If there are cracks on the bare slab, open the crack in V Groove and fill it with ready to use repair polymer modified mortar based on special cements, aldehyde based polymers with thixotropy modify ingagents. If there are lots of honeycombs and identified bad patches of concrete the same should be grouted as per the instructions of site incharge. (The grouting shall be paid separately). Clean the entire surface thoroughly and over this prepared surface, apply three coats of polymeric Cementitious waterproofing coating having a non-toxic, 2-(methoxy carbonyl) - 1-propene - Butyl - 2 propenoate (MPBP)based polymeric waterproofing solution as approved by Engineer incharge. Provide and lay 112 mm average thickness of brick bat coba in cement mortar 1:5 over 12 mm thick CM 1:3 bedding with one pouch of 330 grams of thorough blend of special cements, aldehyde based polymers, shrinkage compensating agents as approved by Engineer in charge per 50 Kg bag of cement and finishing with 20 mm thick cement plaster in cement mortar 1:3 by mixing one 330 grams pouch of above admixture per 50 Kg bag of cement, including all lead, lifts and laid to proper slope to drain off water entirely preparing bell mouth including watta, beveled or champhered portion at the junction of parapet and work up to a height of 300 mm or as directed and including finishing the top layer of water proofing treatement with false marking of 30cmx30cm or as directed, curing and covering the whole treatment. MPBP Polymeric Waterproofing Coating for Concrete and Masonry should have following minimum properties: (1)Elongation% (ASTMD412-2016) : @100% (2)Tensile Strength N/mm2 (ASTMD412-2016) : 3.3 (3) Specific Gravity : 1.02±0.02 (4) Total Solids (ASTMD1644-2012) : 43.98 (5) Hardness Shore A (ASTM D2240-2015): 82
Providing and laying jointless Polydee-LM/Dr.fixit / Chemestic and alike a highly flexible elastometric coating for RCC / cementitious surface for terrace waterproofing on B.B. Coba / R.C.C, after application of TP-42/ Dr.fixit and alike Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM/ Dr.fixit and alike @ 700 gms/sqm and applying 2nd coat of Polydee-LM/ Dr.fixit and alike @ 700 gms/sqm and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/sqm to be paid in separate item.) covering 7 years guarantee on Stamp Paper of Rs. 500/- etc. complete. Spec. No.: As directed by Engineer in charge
FLOORING, SKIRTING AND DADO
Providing and laying cement concrete flooring 50mm thick with M15 cement concrete laid to proper level and slope in alternate bays including compaction, filling joints, marking lines to give the appearance of tiles of 30 cm x 30 cm or other size laid diagonally /square etc finishing smooth (with extra cement) in any colour as directed and curing complete. With Natural Sand Spec. No.: Bd.M.6 Page No. 381
Providing and laying in position flooring of flame finish black granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.** Spec. No.: Bd.M. 3 B/Page No. 380
Providing and fixing machine cut machine polished 18 mm to 20 mm thick flame finish black granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1;4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.** Spec. No.: Bd. M.22 B/Page No. 390
Providing and laying in position inlay work in flooring of granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete.** Spec. No.: Bd.M. 3 B/Page No. 380
Providing and laying matt finish ceramic tiles of having size 30 cm x 30 cm confirming to I.S.15622/2006 (group D II-A) and 7 to 8 mm thick for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with white/colour cement slurry cleaning curing etc. complete
Providing and laying ceramic tiles of having size 30 cm. x 30 cm. and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.
Providing and laying Rough Shahabad Stone Flooring 25mm to 30mm thick and of required width in plain/ diamond pattern on a bed of 1:6 C.M. including cement float, striking joints, pointing in cement mortar 1:3 curing and cleaning etc. complete.
DOORS, WINDOWS AND VENTILATORS , RAILING
Providing & fixing French door with three panel fired in T.W. frame of 125x75 MM thk All rails in 12mm thk double ply & both side 6mm ply with laminate finish. Both panels are in 12 MM thk double ply with laminate finish as per detail drawings. With all necessary fixtures fittings & polishing etc. complete approved by Architect. FD1
Providing & fixing in position French door of s panels with teak wood frame of 150 x 100 mm with all rails of 12 mm thk. Double ply & both side 6mm ply with laminate finish with 10 mm thk. M.S.square bars from outside & 8mm thk plain glass from Inside lower panel with 12mm thk double ply & laminate finish from both side as per detail drawings with necessary fittings & fixtures etc. complete FD2
1. Providing & fixing in French door of panels with teakwood frame of size 125x75mm thk. With all rails of 12 mm thk. Double ply & both side 6mm ply with laminate finish with 10 mm thk. M.S.square bars from outside & 8mm thk plain glass from Inside lower panel with 12mm thk double ply & laminate finish from both side as per detail drawings with necessary fittings & fixtures etc. complete. FD3
Providing & fixing Double leaf shutter in 125 x 75 MM thk. teak wood frame with style of 12 mm thk Double ply & 6mm th ply on top & both side laminate finish. Glass of 8mm thk fixed in 12 mm teak moulding & panel of 12 MM + 12mm thk panels & fixed in teak moulding as per drawing with all necessary fixtures etc. complete. D2
Providing & fixing double leaf shutter in 18mm thk double ply frame with lipping 35 mm thk solid core flush door laminate finish on both side & 8mm thk clear glass fixed 8mm thk lipping in 12mm thk teak wood molding as per the detailed drawings with all necessary fixtures etc. Complete. D3 .D5
Providing & fixing 35mm thk solid core flush door with 18mm thk Double frame with lipping. Laminate finish of approved color with glazing of 8mm thk Clear glass fixed with 8mm thk lipping with grooves as per design & detail drawings with stainless steel fixtures etc. complete. D4
Providing & fixing single leaf 35mm thk Solid core flush door with laminate finish both side fixed in 18mm thk double ply frame finish in laminate & 12mm lipping on the face. & 18mm thk. Teak wood lipping fixed on shutter as per detail drawing with all necessary fixtures & fitting, polishing etc. complete D6
Providing & fixing 35mm thk Solid core flush door with both side laminate & 12mm thk teakwood moulding with 8mm thk Glass fixed in 8mm lipping with both side 3mm glass film S.S.brush metal handle & Aldrop etc. complete as per detailed drawings. D7
Providing & fixing solid core marine ply flush door 35mm thk With PVC coating on all sides in single leaf/Double leaf with glass 8mm thk fixed in 8mm thk Lipping with both side 3mm glass film with necessary S.S.fixtures etc. Complete. D7A
Providing & fixing double leaf shutter of 35mm thk solid core flush door with laminate finish both side fixed in 18mm thk Double ply frame with laminate finish & 8 mm thk lipping for exposed with 8mm thk Clear glass fixed in 8mm lipping, 12mm thk teakwood. molding to be fixed as per detail drawings. with all necessary fixture, fittings polishing etc. complete D9 ,D8
Providing and fixing steel frame door of angle 50 x 50 x 6 mm with mild steel bars 16 mm dia. horizontally at 10mm c/c for ventilator portion including iron hold fast boxes for fixing shutters including welding, finishing, painting etc. complete.
Providing & fixing Sliding/Openable M.S. Gate made out of MS box, Flat, Angle, Channel, Square/Round bars, Flat, Plate section with shutter, frame of box and grill as per design with pivot hinges perforated sheet etc. complete including one coat of zink chromide (Asian, ICI make) primer and two coats of satin finished enamel paint (Asian, ICI make) as per detail drawing and directed by Architect / engineer incharge
Providing and fixing steel ventilator fully glazed partly fixed as per detailed drawing with hot dip zinc coating including fabricating glazing with plain / obscured glass pans 5 mm thick and approved type quality and iron oxidized fixtures and fastening with guard square bars 12 mm 10 cm c/c and oil painting 2 coats etc. complete.
Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5mm thick plain glass with all required screws and nuts etc, complete. With powder coating withoutbox. Spec : As directed by Engineer In Charge
Providing and fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 mm at weight 1.070 kg/Rmt.. Top and side track section 92 x 31.75 x 1.30 mm at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 mm at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineer-in-charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nuts etc, complete, With powder coating without box. Spec : As directed by Engineer In Charge
Providing and fixing in position alluminium openable window of any size as per detailed drawing and as directed by Engineer-in-charg`e with all necessary alluminium sections including necessary fixtures and fastening with 5 mm thick clear float glass etc. complete. b) With powder coating Spec : As directed by Engineer In Charge Note – While arriving at the rate of item weight at 6.90 kg / Sqm is considered
Providing and fixing in position alluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineer-in-charge with all necessary alluminium sections including necessary fixtures and fastening such as 5 mm thick clear float glass etc. complete. b) With powder coating Spec : As directed by Engineer In Charge Note – While arriving at the rate of item weight at 6.90 kg / Sqm is considered
Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38mm x 1.22mm box type, 5mm thick sheet glass louvers, of approved quality etc. complete. Spec : As directed by Engineer In Charge
Providing and fixing mild steel grill work for windows, ventilators etc. 20 kg./sq.m. as per drawing including fixtures, necessary welding & painting with one coats of anticorrosive paint & two coats of oil painting complete. Spec. No.: Bd.U.1 Page No. 537
Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 6248-1979) (With mechanical gear) Spec. No.: Bd.T.55, Page No. 510
Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.2m center to center and 3 pipes of 12mm diameter fixed horizontally including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete.** Spec. No.: As directed by Engineer Incharge **Note**—For item no. 58 to 60 prior approval of Superintending Engineer will be required
Providing and fixing 900mm high S.S.304 Grade Stainless steel railing with 40mm diameter and 1.5mm thick at top,40mm diameter and 1.5mm thick vertical supports spaced at 1.5m center to center and 10mm thick toughened glass including fabricating ,fixtures, errecting , necessary welding , grinding , finishing, buffing to stainless steel pipe etc. complete.** Spec. No.: As directed by Engineer Incharge
Providing and fixing mild steel grill railing weighing 20Kilogram/ One Square Metre. with PVC handrail cover and newel post for staircases, including fabricating, fixtures, drilling holes in concrete / other surface, erecting the grill work, necessary welding, fixing by nuts and bolts, fixing PVC handrail cover, with one coat of anticorrosive paint and two coats of oil painting with approved colour and shade, remaking the damaged surface, cleaning, etc. complete. Spec. One Number : As directed by Engineer in charge.
PAINTING WORKS
Providing and applying 2 coats of flat oil paint of approved colour and shade to internal / external plastered surfaces including scaffolding if necessary, cleaning and preparing the surface (excluding primer coat) complete. Spec. No.: Bd.0.7 Page No. 406
Providing and applying priming coat on concrete/ masonary/ Asbestos Cement plastered surfaces including scaffolding if necessary, preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter and sand papering as required etc. complete.
Providing and applying pearl/ luster finish paint of approved colour and shade to the existing plaster surface including scaffolding, preparing the surface, applying the acrylic wall putti etc. complete. Spec : As directed by Engineer In Charge
Providing and applying JOTUN PAINT first coatis water proofing, flexible, thick exterior emu. Coating. second coait is Local dolpur stone texture & covering unevenness and small cracks in the concrete. final coat is Jotashield ColourXtreme has weather resistant grade of TiO2 with special IR reflecting pigment that offers supreme SRI that offers upto 18-20% drop in surface temperature and upto 5 degree reduction of interior temperature.
Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.
Providing and applying external raincoat painting with crack filling acrylic polymer based chemical compound coating to the external surface of walls to prevent water seepage in the masonry walls during monsoon added with required shade Steiner to give required shade to the surface in two coats. Including providing three coat of priming of polymer base primer including preparing surface scrapping the existing loose old paint, removing loose particles of sand on the surface opening and cleaning the cracks developed in the external plaster, removing loose particles by chiseling, filling cracks by chemicals compound of approved make with proper penetration etc. Coating of Raincoat with the help of brush and as per instructions and specification given by manufacturer and with instruction from Engineer in- charge. Work shall be executed by certified applicator only and covering gurantee of 3 years on court stamp paper of Rs. 500/- and necessary testing etc. complete.
STRUCTURAL WORK & ROOF
Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade etc. complete. Spec. No. : As directed by Engineer-in-charge.(TRUSS, RAILING, DUCT FINCE)
Providing structural steel work in single stanchions composed of R.S.J.Channel etc. with caps, bases, mild steel plated, angle brackets, cleats, gusset plates, anchor bolts etc. as per detailed designs and drawings or as directed including cutting, fabrication, hoisting, erecting fixing in position, making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it two. coats of oil painting approved quality and shade etc. complete.
CATWALK
STAGE MANDAPI
DUCT CLOSING & WALKWAY ALL INCLUSIVE
GIRDDER BEAM with bracing above upto 6 m
Providing and fixing colour coated Zincalume (R) AZ150 (min150gms/sq.mt. total one ach side) profiled sheets for roofing.The feed materialis manufactured out of nominal 0.45mm Base Metal Thickness(BMT) (0.5mmTCT), Hi-strength steel withmin.550MPa yield strength, metallic hot dip coated with Aluminium-Zincalloy (55%aluminium 43.4%zinc 1.6%silicon) with COLORBOND(R) steel quality super durable polyester paint coat (with inorganic pigment). The paint shall have a total coating thickness of nominal 35um, comprising of nomina l25um exterior coat on top surface and nominal 10um reverse coat on back surface. Profile sheet shall have nom. 950-1050mm effective cover width and nominal 25-30mm deepribs with subtlesquare fluting in the five panatnominal 180-250mm center-to-center. The endrib shall be design edforanti-capillary groove. and return leg. The feed material should have coil manufacturers product details markeda regular interval. Including fasteners with min. fastened withmin. 25um Zinc-Tinalloy coated, Hexhead, self-drilling screw etc. complete. (weight of profile 4.52kg/sqm)
Rockwool as a insulating material sandwitched between metacolour sheet . Of density 65kg/cum, make Rockwool india / UP Twiga.
Providing & fixing poly corbonate roof sheet 10 mm thickness (Brand Lexan Make, Colour Clear Sabin)to close toilet duct as per design and drawing Including, self-drilling screw, etc. complete.
FALSE CEILING
Providing and fixing false ceiling of 12mm thick tubular Acoustic Armstrong/ Everest/ AMS boards of approved make, shape and sizes as per drawings including powder coated G.I. wall angle of 20mm x 20mm size, G.I. grid runners of size 20mm x 38mm at 600mm center to center both ways and suspended using G.I. wire 3mm wire including fixing using butterfly clips and fasteners including transporting, scaffolding all necessary labour and machinery, finishing etc. complete. Spec : Bd. R. 19 Page No. 462
Providing and fixing frame work of galvanised iron for suspended false ceiling which includes galvanised iron perimeter channels of size 27 mm & 0.5 mm thick having one flange of 20 mm and another of 30 mm along with perimeter of the ceiling, fixing in brick wall / partition with the help of rawal plugs and screws, suspending galvenised iron intermediate channels of size 45 mm and 0.9 mm thick with two flanges of 15 mm each from the soffit at 1200 mm centers with steel galvanised iron hanger of width 25 mm x 0.5 mm fasteners, ceiling section of 0.5 mm thickness having curved wedge of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 450 mmcenters, 12.5 mm dry walls screws at 230 mmcenters; fixing screws mechanically either with screw driver or drilling machine with suitable attachmentetc. complete. Spec :As directed by Engineer in charge.
Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete
Providing & fixing 6 mm thk texured shera wood plank 1200 x 150 mm fixed with screw to 12 mm thk waterproof marine ply base recommaneded company . ( excluding frame work & runners ref dsr item 13/17 BDR )
Providing and fixing 15 mm thick eco-friendly densified edge calcium silicate false ceiling of approved texture of size 595mm x 595mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections (galvanising at @12 gm/sq.m including both sides) consisting of main T runner suitably spaced at joints to get required length and size 24X38mm. made from 0.33mm thick(minimum ) sheet, spaced 1200mm center to center and cross T of size 24X28mm made of 0.33mm thick(minimum ) sheet to be interlocked at the middle of the 1200x600 mm panel to form the grid of size 600x600mm resting on periphery walls/partitions on a perimeter wall angle precoated steel of size 24x24x3000 made of 0.4 mm thick (minimum) sheet with the help of all plugs at 450mm and laying 15 mm thick densified edges calcium silicate ceiling tiles of approved texture (spintone/cosmos/hexa) in the grid, including light fittings , fixtures , smoke detectors etc., wherever required. Main T runners suspended from ceiling with using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling using 12.5mm dia. And 50mm long dash fasteners, 4mm G.I. adjustable rods with galvanized steel levels clips of size 85x30x0.8mm, spaced at 1200mm center to center along main T bottom exposed with 24mm of all T-sections shall be prepainted with polyester baked paint, for all heights, as per specifications, drawings etc. complete.(currently this item should be used only for VIP cabins)
Water Supply and Sanitary Fitting
Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 mm x 450 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 m x 0.60 m and height is 0.75 m)
SITC of Electric Traction Passenger Lift with 1299498 • Rated capacity :- 10 Passenger/680Kg • Floors :- G+1 floor (2 Stops/2 Landings) • Travel :- 3 to 4.2 mtrs • Location of Lift Machine:- MR/MRL • Rated speed :- 1.0mps VS • Car/Landing door clear opening of 800 mm wide x 2000 mm high • Clear Car size of ......mm wide x ......mm deep x 2250mm high • Lift shaft available having clear size of ......mm wide x ......mm deep, ......mm Pit depth, ………mm Overhead. • Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory). • Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge. • COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor. • LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings. 17-1-4 Job Page 248 of 298 Item No (1) Short Description (2) Unit (3) Completed rate (4) • Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as over current, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters. The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class. • ARD complete with necessary SMF VRLA batteries. • Fireman controller having fireman switch at fire Landing. • CCTV surveillance system comprises of 2 nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min.18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. • Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength. • Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work. • Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT. • General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. • The above rate includes Fully Comprehensive AMC for one year from the date of commissioning.
SITC of Electric Traction Passenger Lift with 1299498 • Rated capacity :- 10 Passenger/680Kg • Floors :- G+1 floor (2 Stops/2 Landings) • Travel :- 3 to 4.2 mtrs • Location of Lift Machine:- MR/MRL • Rated speed :- 1.0mps VS • Car/Landing door clear opening of 800 mm wide x 2000 mm high • Clear Car size of ......mm wide x ......mm deep x 2250mm high • Lift shaft available having clear size of ......mm wide x ......mm deep, ......mm Pit depth, ………mm Overhead. • Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory). • Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge. • COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor. • LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings. 17-1-4 Job Page 248 of 298 Item No (1) Short Description (2) Unit (3) Completed rate (4) • Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as over current, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters. The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class. • ARD complete with necessary SMF VRLA batteries. • Fireman controller having fireman switch at fire Landing. • CCTV surveillance system comprises of 2 nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min.18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. • Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength. • Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work. • Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT. • General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. • The above rate includes Fully Comprehensive AMC for one year from the date of commissioning.
Internal Plumbing
Providing and fixing 100 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. com-plete. Spec : As directed by Engineer In Charge
Providing and laying cast iron pipes of B class of 80mm diameter with sockets and spigot ends/ flanges and cast centrifugally/ vertically including specials, laying pipes and back filling the trench complete including excavation. Spec. No.: Bd.V.1 Page No. 547
External Plumbing
Pumping Machinary - UGT To OHT
Supplying and erecting submersible pumpset of required HP with 415 V, 50 c/s AC supply suitable for 150 mm dia. borewell, suitable for 250 to 700 LPM discharge at 55 to 25 m head & (max efficiency at 40 m head & 500 Ipm discharge & delivery pipe of necessary diameter with a necessary H. type clamp. As per specification o. WP-SMP
Supplying & erecting Water lavel controller 230/ 415V AC., Four way for under ground & Over head tank operation .
Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.c. Submersible/centrifugal pump set upto 7.5- 10 HP consisting of DOL starter having relay range 13-21 AMP,S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof encloser with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase inbalence etc ( Similar to LT model no.MU G10 / CAT NO. SS95983 )
Supplying and erecting 100mm dia. gun metal sluice valve at position with necessary materials.
Supplying and erecting Non return valve 100mm dia in position made of gun metal.
Supplying and erecting 0-100 lb/sq. inch pressure gauge having 4" dia complete with socket for 1/2" G.I. pipe.
Rising Mains (UGT to OHT)
Providing and fixing on walls/ ceiling / floors, ISI mark of below diameter ASTM uPVC SCHEDULE 80 pipes with screwed sockets & brackets, joints and necessary fittings such as socket's back nuts, elbows, bends, tees, reducers, plugs, clamps etc. including necessary drilling holes in walls, slabs, beam etc. and remaking good the demolished portion to restore the same in original condition neatly, testing etc. complete. (Prior approval of sample and brand by Executive Engineer is necessary before use).NON DSR
32 mm dia
40 mm dia
50 mm dia
65 mm dia
80 mm dia
100 mm dia
Providing and fixing of below dia PVC Ball Valve of approved make including necessary sockets / unions, nut, testing etc. complete. (Prior approval of sample and brand by Ex. Engineer is necessary before use) NON DSR
32 mm dia
40 mm dia
50 mm dia
65 mm dia
80 mm dia
100 mm dia
Excavation for foundation in hard murum including removing the excavated materials upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m)By Mechanical Means Spec. No.: Bd.A.2 Page No. 259
Filling in plinth and floors with contractors soil sand or murum in 15cm to 20cm, layers including watering and compaction complete. Spec. No.: Bd.A.11 Page No. 263
External Drainage System
Providing and laying concrete pipes of I.S.NP. class of 150mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573
Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573
Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573
Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. Spec. No.: Bd.V.38, Page No. 572
Providing & constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. Spec. No.: Bd.V.43, Page No. 574
Providing & constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. Spec. No.: Bd.V.43, Page No. 574
Providing and constructing on sewer, B.B. masonry circular manhole with concentric cone 1.2 M dia. at bottom and 0.5 M dia. at top and upto a depth of 2.00 M with 23 cm brick work in CM 1:4 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channel in smooth rendering, providing C.I.dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia.etc. complete as directed by Engineerin-charge.
Providing and constructing on sewer, B.B. masonry circular manhole concentric cone 1.5 M dia. at bottom and 0.5 M dia. at top and upto a depth of 5.00 M with 23 cm brick work, upto depth of 2 M from top and 35 cm thick brick work for balance depth in CM 1:4 proportion with 20 mm thick smooth plaster on both sides in CM 1:2 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channels in smooth rendering, providing C.I. dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia. etc. complete as directed by Engineerin- charge.
External Stormwater System
Providing and laying concrete pipes of I.S.NP. class of 225mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573
Providing and laying concrete pipes of I.S.NP. class of 300mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. Spec. No.: Bd.V.41, Page No. 573
Providing ISI standard R.C.C. pipes in standard lengths of following class and diameter suitable for either collar joints or rubber ring joints, including all taxes (Central and local), inspection charges, transport to departmental stores / site, unloading and stacking, etc. complete.(IS-458/1988)
450mm dia
Excavation for foundation in hard murum including removing the excavated materials upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.50 m)By Mechanical Means Spec. No.: Bd.A.2 Page No. 259
Filling in plinth and floors with contractors soil sand or murum in 15cm to 20cm, layers including watering and compaction complete. Spec. No.: Bd.A.11 Page No. 263
Providing & constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. Spec. No.: Bd.V.43, Page No. 574
Providing & constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W.pipes, Brick Masonry, plastering from inside and with frame fixed in cement concrete etc. complete with R.C.C. Cover. Spec. No.: Bd.V.43, Page No. 574
Providing and constructing on sewer, B.B. masonry circular manhole with concentric cone 1.2 M dia. at bottom and 0.5 M dia. at top and upto a depth of 2.00 M with 23 cm brick work in CM 1:4 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channel in smooth rendering, providing C.I.dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia.etc. complete as directed by Engineerin-charge.
Providing and constructing on sewer, B.B. masonry circular manhole concentric cone 1.5 M dia. at bottom and 0.5 M dia. at top and upto a depth of 5.00 M with 23 cm brick work, upto depth of 2 M from top and 35 cm thick brick work for balance depth in CM 1:4 proportion with 20 mm thick smooth plaster on both sides in CM 1:2 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channels in smooth rendering, providing C.I. dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia. etc. complete as directed by Engineerin- charge.
HYDRNT SYSTEM PUMP ROOM AND EQUIPMENT
SITC of Horizontal,centrifugal,back pull out electric driven main/Standby fire pump, complete with suitable size, duly coupled on a common base frame with all required accessories for the following data. (Hydrant & Sprinkler Service) Supplying, installation, testing and commissioning of main fire pump (MFP / EP) suitable for water discharge of 1800 to 2280 LPM at 80 to 60 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 37kW or of suitable kW capacity for manual/automatic operation and consisting of following :(a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.(d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP
1. Capacity :2280 lpm
2. Head : 70 mtr
3. Impeller : CI Impeller
4. Body : Cast Iron.
SITC of Horizontal,centrifugal,back pull out Disel Engine Pump driven fire pump, complete with suitable size, duly coupled on a common base frame with all required accessories for the following data. (Hydrant & Sprinkler Service) Supplying, installation, testing and commissioning of main fire pump (MFP/DP) suitable for water discharge of 1600 to 1800 LPM at 70 to 50 m head driven by 45 HP or suitable HP capacity diesel engine at required working speed suitable for manual/automatic operation and consisting of following :(a) Horizontal type, single stage, centrifugal casing pump of cast iron body &bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520.(b) Water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12/24 volts DC electric starting equipment with battery of required AH capacity with necessary charger suitable to work on 230v, 50Hz AC supply, diesel tank of minimum 150ltr capacity with first filling of diesel up to 100% level with necessary piping with valves up to engine, exhaust pipe extended up to 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and protection as per standard specification, stop solenoid for auto stop in the event of fault with audio indications etc. as required. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with engine assembly and accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/DP
1. Capacity :2280 lpm
2. Head : 70 mtr
3. Impeller : CI Impeller
4. Body : Cast Iron.
Supplying, installing, testing & commissioning of Jockey Pump 180lpm@70 mtr Supplying, installation, testing and commissioning of jockey fire pump (JP) suitable for water discharge of 180 to 240 LPM at 70 to 50 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 5.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, multi stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete, as per specification no. FF-MFP/JP
1. Capacity :180 lpm
2. Head : 70 mtr
3. Impeller : CI Impeller
4. Body : Cast Iron.
Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG
Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS Each 1763
Supplying and erecting 300 mm dia 1.5m in height air vessel / tank fabricated from min 5mm thick M.S. sheet complete as per specification no. FF-FFA/ACT
Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV
Foot Valve
Supplying and erecting 100 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV
Supplying and erecting 80 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV
Booster Pump: Supplying & installing of Kirloskar make Booster pump of 900 LPM @ 42 meter head Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 900 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 7.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of cast iron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d)Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/BP
1. Capacity :900 lpm
3. Impeller : CI Impeller
4. Body : Cast Iron.
Providing & erecting 3 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB
Providing & erecting incoming and outgoing cable alleys suitable for MCCB panel board with door, 250A incoming and 2 way outgoing made from CRCA sheet 1.6 mm thick duly powder coated and having vertical insulated partition for shielding between the shared face of cable way and DB complete.
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU
Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.
Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.
Supplying and laying (including excavation of suitable width & depth up to 90 cm) 120 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.
Non Return Valve
Supplying and erecting 150 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV
Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV
Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV
Butterfly Valve
Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV
Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV
Supplying and erecting 75/80 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV
GI C Class Pipe Pump room
Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP
WET RISER AND COURTYARD
Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP
Hydrant Valve
Supplying and erecting gun metal single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV
Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL
Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specifications no. FF-FFA/NZ
Hose Box
Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve of size ( 400 x 400 x 400)mm or hose pipe box of size ( 600 x 600 x 200)mm made from min. 1.5 mm thick CRCA sheet with angle iron work of min. of size (25 x 25 x 4) mm having front doors with viewing glass of size (200x150) mm and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)
Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)
Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification no. FF-FFA/HV
Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC
Sprinkler System
Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 65 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 40 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP
Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP
Sprinkler Heads
Supplying, erecting, testing and commissioning of quartzoid bulb sprinkler, 15 mm (½") dia. NBCM Body chrome finished, 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FF-SPR.
FIRE ALARM SYSTEM
Supplying, erecting, testing and commissioning manual call point (Pill box) with break glass push button and flip abort switch or agent release switch in metal enclosure complete as per specification no. FF-FAAS/MCP
Supplying, erecting, testing and commissioning hooters having high (100dB @ 1m) and low (94dB @ 1m) volume setting, group addressing facility allowing multiple sounders to be activated with CRCA enclosure complete as per specification no. FF-FAAS/HTR
Supplying, erecting testing and commissioning optical type smoke detector on suitable back box with necessary connections complete as per specification no. FF-FAS/SD
Supplying, erecting testing and commissioning heat detector with combination "ROR and Fixed Temp." complete as per specification no. FF-FAS/HD
Supplying, installing, testing and commissioning remote response indicators suitable to operate on 5 - 28 V dc supply having FR Polymer ABS Housing complete as per specification no. FF-FAAS/RRI
Providing and fixing, testing and commissioning of installation control valve of cast iron body and brass/bronze working parts comprising of water motor alarm, bronze seat clapper and clapper arm hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser /sprinkler system activates, pressure gauge, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate,gasket etc. of size 150mm dia as required.
tank that holds enough liquid to keep the pump submerged until pumping action can be initiated having capacity 100ltr to 500 ltr
Supplying, installing, testing and commissioning of (2 Zones X 2 Zone) Microprocessor based conventional fire alarm control panel (FACP) with standard accessories , 16x2 Character LCD Display, provision for zone wise contact and beep sound alarm, suitable to operate on 120-220 V AC, 0 - 49 Deg C, 93 ± 2 Percentage RH (non- condensing) at 32 ± 2 Deg C complete as per specification no. FF-FAAS/FACP
2) For Item no.13-9-14 increase rate by 25% for additional zone as per requirement
Powder Coated 2 Hours Fire Door - Single Leaf - 1200 X 2100 mm. Providing and fixing of approved make 120mins Hollow metal fire rated doors tested and certified design as per IS 3614 part-2 & BS 476 part-20 & 22 at NABL Approved Laboratory for its stability and integrity
Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU
FIRE EXTINGUISHER
Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 /15683 of 6 kg capacity with necessary clamp for erection on wall.
Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.
Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.
PLOT DEVELOPMENT & COMPOUND WALL
Compound Wall & Gate
Excvation, Filling & Soling
Excavation for foundation in earth, soil of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 m. beyond the building area & stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.)By Mechanical Means
Filling in plinth and floors with contractors soil sand or murum in 15 cm to 20cm, layers including watering and compaction complete.
Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 cm to 20 cm thick including hand packing and compacting complete. Spec. No.: Bd.A. 12 Page No. 264
Shifting excavated & existing soil including loading in truck and conveying to dumping point approved by pandharpur council, unloading, spreading etc. complete. With all leads and lifts.
CEMENT CONCRETE ( PLAIN & REINFORCED)
Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)
Providing and laying in situ / Ready Mix cement concrete M-20 of trap / granite / quartzite / gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchion set c.including bailing out water, Steel centering formwork, laying / pumping cover blocks, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel)etc. complete, with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Panmixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and laying Cast in situ / Ready Mix cement concrete M-20 of trap / granite / quartzite / gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying / pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine agg.regate (Crushed sand VSI Grade)
Providing and laying Cast in situ / Ready Mix cement concrete M-20 of trap / granite / quartzite / gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying / pumping, compaction and roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer)etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and laying Cast in situ / Ready Mix cement concrete M-20 of trap / granite / quartzite / gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying / pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and laying Cast in situ / Ready Mix cement concrete in M-20 of trap / granite / quartzite / gneiss metal for R.C.C. coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, coverblocks, laying / pumping, compacting, curing, finishing and roughening the mif special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic microprocessor based PLC with SCADA enabled reversible Drum Type mixer / concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade)
Providing and fixing in position TMT - FE - 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.
MASONRY WORK ( STONE AND BRICK )
Providing second class Burnt Brick masonry with conventional/ I.S. type bricks in cement mortar 1:6 in superstructure including striking joints, raking out joints, watering and scaffolding etc. Complete
Providing coursed rubble masonry first sort for pillars of trap / granite / quartzite /gneiss stones in cement mortar 1:6 including pointing with cement mortar 1:3 scaffolding and watering etc.complete.
GRILL
Providing and fixing mild steel grill work for windows, ventilators, etc. 15 Kilogram / One Square Metre as per drawing including fixtures necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.
FERROCRETE
Providing, cutting, bending, bindingas per desired shape, armature reinforcement as per design drawing for ferrocement single skin elements , providing and fixing with overlaps as recommended welded and hexagonal meshes on both sides as per detailed drawing, Providing, cutting, bending binding, as per desired shape, armature reinforcement for stiffening ribs as per design drawing for ferrocement ribs, mixing and mortaring the mortar mix as per detailed mix given with 43 grade OPC and suggested additives, finishing from both sides, maintaining desired line and level where required, curing using hessian cloth and continuours watering as per detailed specifications and work procedure etc complete.
STONE WORK
NEWASA STONE WORK
Providing & fixing cladding to columns & beam surface in Newasa stone of 50 mm thk in size of 275 x175 mm in cement mortor 1:3 with necessary accessaries ,fixture & adhesive of recommanded brands for fixing to supporting back surface with watering etc. complete..Use pigment in mortor for grouting og colour match no natural stone watering etc complete as per as directed by Engineer in charge .) (sadguru ghadai)
Providing & fixing cladding to round vertical coloumns in Newasa stone of 75 mm thk in size of 275 x175 mm as per design & detials shown in drwaings cement mortor 1:3 with necessary accessaries ,fixture & adhesive of recommanded brands for fixing to supporting back surface with watering etc. complete..Use pigment in mortor for grouting or colour match to natural stone watering etc complete as per as directed by Engineer in charge .) (sadguru ghadai)
DHOLPUR STONE WORK
Providing & fixing cladding to vertical surfaces in Dholpur Stone of 75 mm thk in size of 275 x175 mm as per design & detials shown in drwaings in cement mortor 1:3 with necessary accessaries ,fixture & adhesive of recommanded brands for fixing to supporting back surface with watering etc. complete.Use pigment in mortor for grouting og colour match no natural stone watering etc complete as per as directed by Engineer in charge .)
Providing & fixing Arches of various sizes in 150 mm thk .Dholpur stone as per design a details drawings in 1:3 cement mortor with necessary accessaries & adhesive for fixing & erection ..Use pigment in mortor for grouting or colour match to natural stone watering etc complete as per as directed by Engineer in charge .)
Providing & fixing Dome kalash of different sizes in Dholpur stone as per detail design on top of curved surfaces etc complete.as per as directed by Engineer in charge .)
Small size
Big size
RED AGRA STONE WORK
Providing & fixing 20 MM THK Red-agra Stone cladding for sloping chajja on m.s. frame structure as per details & drwings in 1:3 morter/adhesive for joints & also on R.C.C surfaces as per directed by Engineer in charge .)
Providing & fixing Full round bands of 100 thk in Red Agra stone as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .)
Providing & fixing brackets in Red Agra of 100 mm thk of various sizes as per design & drawings with necessary accessaries & adhesive for fixing & erection .as per directed by Engineer in charge .)
Big size
PLASTERING AND FINISHING
Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.
DOOR WINDOW AND GRILL
Providing & fixing Sliding/Openable M.S. Gate made out of MS box, Flat, Angle, Channel, Square/Round bars, Flat, Plate section with shutter, frame of box and grill as per design with pivot hinges perforated sheet etc. complete including one coat of zink chromide (Asian, ICI make) primer and two coats of satin finished enamel paint (Asian, ICI make) as per detail drawing and directed by Architect / engineer incharge
PAINTING WORKS
Providing and applying JOTUN PAINT first coatis water proofing, flexible, thick exterior emu. Coating. second coait is Local dolpur stone texture & covering unevenness and small cracks in the concrete. final coat is Jotashield ColourXtreme has weather resistant grade of TiO2 with special IR reflecting pigment that offers supreme SRI that offers upto 18-20% drop in surface temperature and upto 5 degree reduction of interior temperature.
Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.
ROAD & PLOT FILLING
EXCAVATION, FILLING AND SOLING
Excavation for roadway in earth, soil of all sorts, sand, gravel or soft murum including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50m. and spreading for embankment or stacking as directed.
Providing earth work in embankment with approved materials obtained from other sources upto lead of 50m. including all lifts, laying in layers of 20cm. to 30cm. thickness breaking clods, dressing to the required lines, curves, grades & section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97 % of standard proctor density etc. complete ( Material obtained from Other sources)
ROAD SUB BASE & BASE COURSE
Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader / Paver on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401 -- By Mix in Place Method and Grading - I Material
Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate ( natural sand/ VSI grade finely washed crushed sand) conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, , cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant/ Weigh batch mixer, transported to site with all leads and lifts, laid with a paver with electronic sensor /by suitable means as approved by Engineer-in?charge , compacting with vibratory roller, finishing, curing and including preparation of sub-grade surface if required etc. complete.
Providing and laying in-situ M30 Grade unreinforced plain cement concrete pavement over a prepared sub base with 43 grade cement , coarse and fine aggregate( natural sand/ VSI grade finely washed crushed sand) conforming to IS 383, using fine and coarse aggregates combined gradation as per Table 600-3 of MORTH Specification 2013, mixed in a batching and mixing plant/ non tilting mixer and Weigh batcher as per approved mix design, admixtures, transporting to site, spreading, laying with approved make paver,compacted and finished in a continuous operation, finishing to lines and grades as directed by Engineer-in-charge and curing by curing compound /by providing cement vata in cement Mortar 1:8 @0.6m X 0.6m centre to centre, admeasuring 80 mm at bottom and 40 mm at top with depth of 75mm and maintaining the same throughout curing period by any other method approved by Engineer-in-charge.
Cutting transverse contraction joints 3 to 4 mm wide and depth 60 mm. .in concrete slab using concrete cutting machine with diamonds tudded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10mm. wide at top having depth of 15 mm. as directed by Engineer incharge.
Providing to contraction joints polysuphide sealent (Pouring grade) confirming to BS:5212 - 1989 into sawed groove widened at top for sealent reservoir of specified size and shape as per detailed drawing including fixing Polyethylene foam backer rod of required diameter (appraox. 25% larger than the initial 3m One Metric Tonne o4 mm. joint) over laid with bond breaking tape as per detailed drawing. Item includes cleaning the joints with waterjet / air compressor and allowing joint to become thoroughly dry before sealent is applied and applying primer. (A) Contraction and longitudinal joints (15 mm. deep x 8 mm.wide)
Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 40 mm thickness of having a strength of 200 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. complete.
Providing and fixing heavy duty inter locking concrete Coloured paving blocks of 80 mm thickness of having a strength of 300 Kilogram/Sq.cm. of approved quality and shape on a bed of crushed sand of 25 to 30 mm thick including skirting joints and cleaning etc. completE
Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb without gutter ( as per IRC 86 1983) embedded 125mm below ground level over M-10 PCC finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plan
Cutting transverse contraction joints 3 to 4 mm wide and depth 60mm. .in concrete slab using concrete cutting machine with diamond studded saw within 48 hours of casting of bay / slab etc. complete including subsequent widening of the groove 8 to 10 mm. wide at top having depth of 15 mm. as directed by Engineer incharge.
Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395 : 1997 below concrete pavement including all materials and labour complete.
ELECTRICAL WORKS
Substation, Earthing & Lightining Arreaster
Supplying, installation, testing and commissioning extendable/non-extendable outdoor type 22 kV 630A, load break isolator switch, compliant to IEC 62271 - 100, 200 and 102, on provided MS channels/trench/foundation as per specification no SW-HTS / LBS
Supplying, installing, testing & commissioning 3 phase, 22/0.433 kV, 50 Hz., 630 kVA, Mineral oil immersed and naturally cooled outdoor type, Copper wound Non-sealed transformer, delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 40℃ by thermometer in oil and 45℃ by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with off load tap changer) off load +5 to -10 in steps of 2.5%, having 7 number of tap positions with standard accessories complete with test certificate with losses below 1953 Watts at 50% load, 5565 Watts at 100% load as per IS:1180 (part 1) : 2014 with necessary permissions of Electrical Inspector, as per specification no SS- TR-NSL
10-1-10 NOTE 1 1) For indoor type transformer add Rs. 18000/- in rate of transformer.
Supplying, erecting, testing and commissioning of diesel generating set with alternator of 320 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2 and maximum fuel consumption 54.89 Ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 480 Ltr etc. on provided M20 Grade CC Foundation and obtaining necessary approval from Electrical Inspector as per specification no. GEN-DG
Supplying, erecting, testing and commissioning of Microprocessor based AMF panel suitable for Diesel Generating Set of above 320 kVA up to 400 kVA capacity Three phase, 415 Volts, 50Hz A.C. with all standard features, safeties etc as per specification no. GEN-AMF. (NOTE 1)
Supplying, erecting, testing and commissioning of Microprocessor based Generator Control Unit (Synchronization panel) panel suitable for diesel generating set of above 320 kVA up to 380/400 kVA capacity Three phase, 415 Volts, 50Hz A.C. with all standard features and safeties etc as per specification no. GEN-SYNC. (NOTE 1)
Supplying, erecting, testing and commissioning 22KV HT metering cubical (compact type) approved by MSEDCL / licensee fabricated with 2 mm (14 SWG) M.S. sheets with supporting angle, painted with powder coating / epoxy paint of required shade, copper bus bar size 25 x 6 mm, heavy duty mechanical lock, with counter meter for measuring no. of times the opening of meter door, top side cover (CT, PT cover) interlock with meter door, epoxy casted 3 nos. CT having required ratio between 5/5A to 25/5A, VA 10 or 15, Class 0.5S, epoxy casted 3 nos. PT having ratio 22000/V3/110/V3 VA 50, Class 0.5 suitable for provided trivector meter, and provision for incoming and outgoing cables complete duly tested by licensee with necessary test certificates and erected on provided plinth/ cc foundation
Supplying standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use, scissors, anti-septic solution, etc. (All above contents shall be of standard makes)
Supplying shock proof leather safety shoes of electrical grade of standard size as IS :11226, 14544 duly tested, with necessary test certificate from manufacturer.
Supplying and fixing PVC synthetic elastomer electrically insulating mat with class A insulation conforming to IS: 15652 – 2006 having 2 mm thickness up to 3.3 kV
Providing printed instruction chart for treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete
Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working upto 22 kV supply complete
Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.
Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP
Supplying and erecting copper strip of high purity required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per specification no. EAEP.
Supplying and erecting G.I. strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joint required. as per specification No (EA-EP).
Supplying and erecting annealed bare copper wire of high purity of required sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws complete.
Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws complete.
Supplying & erecting conventional spike type air termination suitable to carry lightning stroke made up of heavy gauge 40 mm dia copper pipe of standard length with 5 Nos. copper spikes fixed on copper ball as air terminals duly threaded in copper pipe erected on provided foundation complete.
Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 150 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.
Providing and fixing reinforced cement concrete cover of size 60 cm x 45 cm with frame over inspection chamber etc. complete of medium duty (100 Kilogram).
Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with coupling collar of standard thickness at required depth up to 90 cm below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).As per wording and as per instruction of Engineer-in-charge
Supplying & laying (including excavation) 25 cm dia RCC Hume pipe of standard thickness at required depth up to 90 cms. below road / ground surface, for covering provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet). As per wording and as per instruction of Engineer-in-charge
Making burnt brick masonry with 1:6 ratio cement concrete duly plastered including watering, streaking joint on exposed faces, rocking at joint on exposed faces and watering complete. As per wording and as per instruction of Engineer-in-charge
LT Panel and Distribution Boards
Supplying and erecting 150 kVAr, 440 V 3 phase, 50 Hz., Contactor Logic & Intelligent Relay micro APFC passive filter panel, consisting of suitable steps of APP/MPP type capacitor units with Detuned (harmonic filter) reactors of suitable rating , APFC panel shall be compliance to IEC 61439 and power quality IEC 61921 standard as per specification no CP-ED/APFC
Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB
Supplying, erecting & marking TPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB
Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuitbreaking capacity (Icn) 10kA in provided distribution board as per specificationno. SW-SWR/MCB
Supplying & erecting triple pole and neutral distribution board (TPNDB),SPMCB of 8 ways / phase (24 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) asper specification no. SW-SWR/MCBDB
Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 12 ways /phase (36 poles), with door, 1.2mm thickness surface/flush mounted, IP 43 Protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB
Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB
Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 10 ways (10 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB
Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.
Supplying and erecting blanking plate of suitable size on MCBDB.
Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/ 4 pole MCCB as incomer & outgoing SP MCB (12 poles) or TP MCB of 4 ways (12 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1
Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (24 poles) or TP MCB of 8 ways (24 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1.
Supplying, erecting & commissioning 2 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB
Supplying, erecting & commissioning 4 pole RCCB 16/25A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB
Supplying, erecting & commissioning 4 pole RCCB 40A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB
Supplying & erecting minimum three & above star rated Centrifugal water pump (Monoblock), 415 V, three phase 50 cycles A.C. supply of 5.625 KW/7.5 HP with discharge of 780/170 Litres per Minute (LPM) for head of 33/54 m and 80mm suction/ 65mm delivery pipe of size, on provided C.C. foundation as per specification No. WP-CGP
Supplying & erecting automatic control panel for 3 Phase , 415 volt, A.C, Submersible/centrifugal pump set up to 7.5 HP consisting of DOL starter having relay range 9-14 AMP,S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc
HT & LT Cables, End Termination & Cable Trays
Supplying , erecting & terminating XLPE insulated galvanised steel formed wire armoured (strip) cable 22 kV(E), 3 x 95 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT NOTE 2 2) For round wire armouring increase rate For 11 kV (E) by 31%
Providing and erecting Heat shrinkable out door termination kit for 22 kV ( E ) XLPE HT cable 3 x up to 95 sq. mm. with necessary material as per specification No. CB-JT/HT
Providing and erecting Heat shrinkable indoor termination kit for 22 kV ( E ) XLPE HT cable 3x up to 95 sq. mm. with necessary material as per specification no. CB-JT/HT
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½core 240 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU
Point Wiring, Modular Switch & Socket & Fitting
Supplying and erecting PVC box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX
Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories
Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.
Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.
Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC.
Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit
Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW
NOTE 3 3) Rates of earth wire shall be calculated as one half rate of mains of bunch of two wire
Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places.as per specification No: WG-MA/BW
NOTE 3 3) Rates of earth wire shall be calculated as one half rate of mains of bunch of two wire
Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.
Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete.
Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete
Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.
Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete
Supplying and erecting modular type blanking plate one module, duly erected on provided plate & box.
Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.
Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.
Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 4 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.
Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.
Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 8 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match thebackground
Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.
Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 16 / 18 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background.
Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WGPW/SW.
Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing ncapping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW
Secondary point wiring for additional light/ bell point, concealed type in min 20 mm FRLS grade PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires with required accessories as per specification No: WG-PW/CW
Supplying and erecting fresh air cum exhaust fan of light duty 250 V A.C. 50 cycles 300mm. 1400 RPM rust proof body & blades, wire mesh, duly erected, complete
Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF
Supplying & fixing anchor type fastener fan hook, with 2 nos. of 10 mm dia x 75 mm long with necessary materials for ceiling fan
Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.
Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.C. SMOKE EXHAUST set up to 7.5 HP - 10 H.P. consisting of DOL starter having relay range 28-42 AMP,S.P.P., Combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc.
Supplying and erecting LED square / circular Max. 11 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.
Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.
Supplying and erecting LED Strip light 5m Length Max. 45 W IP20 class having minimum lumens output of 800 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f.>0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50, including driver with 1 year warranty
Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty
Supplying and erecting anodized aluminium corridor / passage / mirror light LED fitting (2 feet) Max. 12W with high transitivity diffuser with min. system lumens output of 1200 lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs.at L70B50, including driver with end caps on provided PVC Block / wooden board with 3 years warranty.
Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.
Supplying and erecting LED square / circular Max. 14 W down lighter/Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 1500 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. (AUDI)
Supplying and erecting LED square / circular Max. 7W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 770 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty. (AUDI)
upplying, installing, testing and commissioning of single phase, 230V, 50 Hz, 2500 VA digital pure sine wave inverter with backup time of 30hrs. based on Insulated Gate Bipolar Transistor (IGBT) technology complete as per specification no. AP-INV
Supplying and erecting 12V/100Ah tubular battery with battery terminal wire, duly charged with 36 months warranty complete
Supply, Installation, testing and commissioning of cubical type MV Panel conform to IEC:61439-I as per technical specifications,single line diagram & approval of Drawings prior to manufacturing, packed in wooden crates with PVC sheets inner packing, transport to site, compartmental cubicle type freestanding with appropriate cable entries, front operating, front maintained wherever required complete with base frame etc. erected in 14 gauge CRCA sheet and surface treated with phosphating seven tank process and duly powder coated with MSEDCl approved color, feeder piller should be with supporting angles, self-locks, gasket and slanting top to be erected on provided foundation Name: Main LTFP 01 Duty: Indoor Type (IP 42) Location: Substation Incomer: 1000A FP ACB with LSI release with R, Y, B & On , OFF, Trip indications and required accessories. Busbar: 1000A AL busbar. Outgoing: 1 No of 630A TPN HRC fuse switch with neutral link. 1 No of 400A TPN HRC fuse switch with neutral link. 2 No of 250A TPN HRC fuse switch with neutral link. 1 No of 100A TPN HRC fuse switch with neutral link. 1 No of 320A TPN HRC fuse switch with neutral link. 1 No of Space Provision
Supply, Installation, testing and commissioning of cubical type MV Panel conform to IEC:61439-I as per technical specifications,single line diagram & approval of Drawings prior to manufacturing, packed in wooden crates with PVC sheets inner packing, transport to site, compartmental cubicle type freestanding with appropriate cable entries, front operating, front maintained wherever required complete with base frame etc. erected in 14 gauge CRCA sheet and surface treated with phosphating seven tank process and duly powder coated with MSEDCl approved color, feeder piller should be with supporting angles, self-locks, gasket and slanting top to be erected on provided foundation 'Panel Details: Name: DG DISTRIBUTION PANEL Duty: Outdoor Type (IP 54) Location: Substation Incomer: 2 No. 630A FP ACB with LSI release with R, Y, B & On , OFF, Trip indications and required accessories.. Busbar: 1000A AL busbar. Outgoing: 1 No of 800A TPN MCCB. 1 No of 630A TPN MCCB. 1 No of 400A TPN MCCB. 1 No of 320A TPN MCCB
Supply, Installation, testing and commissioning of cubical type MV Panel conform to IEC:61439-I as per technical specifications,single line diagram & approval of Drawings prior to manufacturing, packed in wooden crates with PVC sheets inner packing, transport to site, compartmental cubicle type freestanding with appropriate cable entries, front operating, front maintained wherever required complete with base frame etc. erected in 14 gauge CRCA sheet and surface treated with phosphating seven tank process and duly powder coated with MSEDCl approved color, feeder piller should be with supporting angles, self-locks, gasket and slanting top to be erected on provided foundation Panel Details :- Name -CHANGEOVER PANEL Duty -Duty: Indoor Type (IP 42) Incomer-800A FP ACB with LSI release with R, Y, B & On , OFF, Trip indications and required accessories.. Busbar - 800A TPN Al Busbar Outgoings - 1 Nos of 800A FP ACB with LSI release with R, Y, B & On , OFF, Trip indications and required accessories.
Supply, Installation, testing and commissioning of cubical type MV Panel conform to IEC:61439-I as per technical specifications,single line diagram & approval of Drawings prior to manufacturing, packed in wooden crates with PVC sheets inner packing, transport to site, compartmental cubicle type freestanding with appropriate cable entries, front operating, front maintained wherever required complete with base frame etc. erected in 14 gauge CRCA sheet and surface treated with phosphating seven tank process and duly powder coated with MSEDCl approved color, feeder piller should be with supporting angles, self-locks, gasket and slanting top to be erected on provided foundation Panel Details :- Name -AUDI MLTP Duty -Duty: Indoor Type (IP 42) Incomer-800A FP ACB with LSI release with R, Y, B & On , OFF, Trip indications and required accessories.. Busbar - 800A TPN Al Busbar Outgoings - 2 Nos of 200A TP MCCB, 9 Nos of 40A-63 TP MCB 1 Nos of 400A TP MCB,
Supply, Installation, testing and commissioning of cubical type MV Panel conform to IEC:61439-I as per technical specifications,single line diagram & approval of Drawings prior to manufacturing, packed in wooden crates with PVC sheets inner packing, transport to site, compartmental cubicle type freestanding with appropriate cable entries, front operating, front maintained wherever required complete with base frame etc. erected in 14 gauge CRCA sheet and surface treated with phosphating seven tank process and duly powder coated with MSEDCl approved color, feeder piller should be with supporting angles, self-locks, gasket and slanting top to be erected on provided foundation 'Auditorium HVAC PANEL : Auditorium Duty: Indoor Type (IP 42) Location: Terrace Incomer: 200A FP MCCB with LSI release with R, Y, B & On , OFF, Trip indications and required accessories.. Busbar: 400A AL busbar. Outgoing: 10No 16-21A TP MCB 2 No 40A TP MCB
Street Light
Providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL
Supplying and erecting integrated LED street light fitting 60W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 4400 Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto 6500K,THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver complete with 3 Years warranty as per specification No FG-ODF/FLS2.
Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).
Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multistra nded copper Industrial cable for voltage grade up to 1.1 kV
Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU
Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT
Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP
HVAC WORK
HVAC SYSTEM
Supplying, erecting, testing and commissioning of 12HP, VRF/VRV Air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/ suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47॰C, non stop cooling even at 56॰C and COP 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suiable shape for increasing maximum heat transfer area, rain protection cover, built in oil seperator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V+/-10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.
Supplying, erecting, testing and commissioning of 16HP, VRF/VRV Air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/ suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47॰C, non stop cooling even at 56॰C and COP 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suiable shape for increasing maximum heat transfer area, rain protection cover, built in oil seperator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V+/-10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.
Supplying, erecting, testing and commissioning of 18HP, VRF/VRV Air conditioning system outdoor unit (ODU) complies type-IV OEM standards working on HFC refrigerant R410A or other required/ suitable green equivalent refrigerant, for minimum cooling capacity as delivering 100% capacity at 47॰C, non stop cooling even at 56॰C and COP 3.00 to 4.00, modular type vertical hot air discharge suitable for longer piping range upto 1000 metre operation in cooling mode with inverter/digital VRF/VRV technology microprocessor based control compressor starter/control panel with scroll compressor, air cooled copper condenser coil of suiable shape for increasing maximum heat transfer area, rain protection cover, built in oil seperator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V+/-10%, 50 Hz, 3 phase power supply (all suitable for high ambient conditions), internal copper refrigerant piping, internal wiring and refrigerant, etc. all housed in powder coated weather proof cabinet complete.
Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 way cassette room / indoor unit (IDU- compact / standard size) of nominal capacity 3.1TR (1100 cfm) having EER asper BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. IDU with drainage arrangements, fan, refrigerant piping, cordless remote control and fresh air post etc. IDU shall have anti-corrosive coating suitable for coastal area in all respetcs suitable to operate on 1-phase, 230V, 50Hz, AC supply complete. The unit consisting with any additional refrigerant and oil charge as per requirement during installation complete.
Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3mm dia. (OD) for liquid line / suction line of suitable gauge ( hard pipe for liquid main line and soft copper pipe for refrigerant along with necessary supports, hanger,s clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damage,s fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV / VRF air conditioning system complete.
Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9mm dia. (OD) for liquid line / suction line of suitable gauge ( hard pipe for liquid main line and soft copper pipe for refrigerant along with necessary supports, hanger,s clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damage,s fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV / VRF air conditioning system complete.
Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2mm dia. (OD) for liquid line / suction line of suitable gauge ( hard pipe for liquid main line and soft copper pipe for refrigerant along with necessary supports, hanger,s clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damage,s fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV / VRF air conditioning system complete.
Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1mm dia. (OD) for liquid line / suction line of suitable gauge ( hard pipe for liquid main line and soft copper pipe for refrigerant along with necessary supports, hanger,s clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damage,s fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV / VRF air conditioning system complete.
Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9mm dia. (OD) for liquid line / suction line of suitable gauge ( hard pipe for liquid main line and soft copper pipe for refrigerant along with necessary supports, hanger,s clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damage,s fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV / VRF air conditioning system complete.
Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7mm dia. (OD) for liquid line / suction line of suitable gauge ( hard pipe for liquid main line and soft copper pipe for refrigerant along with necessary supports, hanger,s clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damage,s fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV / VRF air conditioning system complete.
Supplying, laying/fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5mm dia. (OD) for liquid line / suction line of suitable gauge ( hard pipe for liquid main line and soft copper pipe for refrigerant along with necessary supports, hanger,s clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating of VRV/VRF piping for protection against mechanical damage,s fungal growth, flame spread, water permeance and ultraviolet radiations with OEM standards of VRV / VRF air conditioning system complete.
Supplying and installatiing of high pressure grade required size copper connection Y or T - joints / refnet complete erected on wall/ ceiling with supports/raceways, nitrile rubber insulation, painting, etc. with brazing and testing for leakages confirming the normal operation of the VRV/VRF air conditing system,
Supplying, erecting, testing and commissioning of manually operated, opposed blade, duct mounted, flanged volume control damper of required sized in GI construction with operating machanism, mounting arrangements, complete. Sizes as mentioned on layout.
Supply, fabrication, installation and testing of flexible canvas connections constructed between ductable unit / dampers / ducting of suitable size with fire resist flexible double canvas sleeve complete.
Providing and applying of adhesive thermal insulation for supply return air duct with 19mm nitril rubber insulation having R-value as per the prevailing provisions in ECBE-2017.
Providing and applying of acoustic insulation for air duct with 25mm thick, 48kg/cu.m fiber glass faced with RP tissue and covered with 26 SWG perforated aluminium sheeets complete.
Supplying and erecting tile type modular diffuser made from aluminium sheet with powder coated matching to the ceiling shade for provided supply and return air complete.
Supplying and installatiing of collar damper of GI material of upto 120 microns for anti corrosive resistance for supply air grill of suitable size.
Supplying and erecting aluminium powder coated linear grill of suitable size for width length without coller dampers having matching colour with the existing false ceiling and suitable for deflection of 15॰/30॰/45॰, etc.
Supplying, installing, testing & commissioning cassette type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor room Air conditioning unit 1.8TR to 2.1TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32/R410A having copper condenser, dust filter, self diagnosis feature, stabilizer free operation, noise level maximum 50dBA at position as per specification no. APAC/ WAC
Supplying, installing, testing & commissioning cassette type room Air conditioning unit 2.8TR to 3.3TR capacity with refrigerant R32/R410A 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega split) mounting type complete with temperature display on indoor unit, dust filter, noise level maximum 50dBA at position as per specification no. APAC/ WAC
Supplying, installing, testing & commissioning cassette type room Air conditioning unit 4TR to 4.4TR capacity with refrigerant R32/410A 415V, 50 Hz, A.C. supply having 1 no of air handling unit (Mega split) mounting type complete with temperature display on indoor unit, minimum dust filter, noise level maximum 50dBA at position as per specification no. APAC/ WAC
Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete.
Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete.
Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater/AC system.
Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater/AC system.
Supplying, erecting, testing & commissioning fresh air intake system, ductable circular inline fresh air fan inlet unit having 300 cfm capacity with maintaining the static pressure minimum 20mm suitable to operate on 1 phase, 230V, 50Hz, A.C. supply complete.
Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation
Supplying, erecting, testing and commissioning of VRF/VRV Air conditioning system working on HFC refrigerant R410A and for extended piping leghts top up of HFC refrigerant R410A, as per actual requirement derived while system commissioning.
Supplying and erecting of HDGI or epoxy painted Stand for ODU of capacities mentioned complete with Configuration with 2 Layers of Ribbed EPDM Rubber Pads with GI Shim in between. The Rubber pads shall be placed between the ODU & the HDGI or epoxy painted Stand.
Supply, Installation, Testing & Commissioning of Hard PVC Schedule 40 Plumbing Grade Drain piping with all fittings and accesspries required to complete the pipingas per specification with 9 mm thk Nitrile rubber insulation. for Dia. 32mm and Dia. 25mm
Supply, Fabrication and installation of GI sheet metal ducts with all support system and accessories required to complete the ductng in accordance with the approved shop drawings and as required by the specifications. ( Ducting = 22G )
Supply, Fabrication and installation of GI sheet metal ducts with all support system and accessories required to complete the ductng in accordance with the approved shop drawings and as required by the specifications. (Ducting = 24G )
Supply, Installation, Testing & Commissioning of Double skin AHU comprising of 48 mm thick panel filled with glasswool, DIDW backward curved / airfoil fan complete with suitable motor and mounting arrangements, thermal break profile, Return air mixing chamber, DX type Cooling Coil - 3 circuits with capillery header / Electronic Expansion Valve to be connected with VRF/VRV ODU system ( AHU VRF KIT of appropriate capacity ), SS insulated drain pan, Inlet Filter EU-5, doors with proximity switch for inspection lamp and AHU stop, including volume control damper and motorized fire damper with fire test control panel at AHU outlet installed, PLC based Control logic Panel with possibilty of third party BMS connectivity for remote operation, etc. Capacity = 17000CFM / 50mmWg / 42TR
Supply, Installation, Testing & Commissioning of Double skin AHU comprising of 48 mm thick panel filled with glasswool, DIDW backward curved / airfoil fan complete with suitable motor and mounting arrangements, thermal break profile, Return air mixing chamber, DX type Cooling Coil - 3 circuits with capillery header / Electronic Expansion Valve to be connected with VRF/VRV ODU system ( AHU VRF KIT of appropriate capacity ), SS insulated drain pan, Inlet Filter EU-5, doors with proximity switch for inspection lamp and AHU stop, including volume control damper and motorized fire damper with fire test control panel at AHU outlet installed, PLC based Control logic Panel with possibilty of third party BMS connectivity for remote operation, etc. Capacity = 8000CFM / 30mmWg / 20TR
Supply, installation, testing and commissioning of Inline Cabinet, Backword curved fan for Toilet Exhaust system complete with drive and Supports system with vibration isolators. Motor shall be suitable for 215 ± 10% volts, 50 cycles, 1 phase AC supply and shall have high efficiency motors, with all supporting structures and accessories. Sound level shall not be more than 55 dBA from 3 m AMCA Certified only. Capacity = 3500CFM / 30mmWg
Supply, installation, testing and commissioning of Inline Cabinet, Backword curved fan for Toilet Exhaust system complete with drive and Supports system with vibration isolators. Motor shall be suitable for 215 ± 10% volts, 50 cycles, 1 phase AC supply and shall have high efficiency motors, with all supporting structures and accessories. Sound level shall not be more than 55 dBA from 3 m AMCA Certified only. Capacity = 2550CFM / 30mmWg
Supply, installation, testing and commissioning of ABS material round Disc Valves of Dia. 125mm for exhaust air with Duct Flow controller of capacity 55CFM each fitted with Disc valve and aluminium flexible connectio to connect with square duct (not more that 1000mm per unit)
Supply, installation, testing and commissioning of Aluminium Door transfer grill for toilet block doors. size 700x400mm. (colour of grill shall be as per Architects approval.)
Supply, installation, testing and commissioning of Vane Axial Smoke Exhaust Fans with Sound Attenuators, complete with drive and Supports system with vibration isolators. Fire rated H Class motor, 300 deg.C at 2 Hr. Motor shall be suitable for 415 ± 10% volts, 50 cycles, 3 phase AC supply and shall have high efficiency motors, with all supporting structures and accessories. Shall be operated by fire panel signal, in case of Fire insident. Sound level shall not be more than 55 dBA from 3 m AMCA Certified only. Capacity = 9500CFM / 15mmWg
ACOUSTIC WORK
following work is to be done at any floor and all heights
Providing & Fixing in position, Acoustical Panelling made from Wood-wool board 20mm on, 50 x 50 mm (+/- 10%) Sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 Gsm FR grade synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge. ( walls of stage)
Providing & Fixing in position, Acoustical Panelling made from 12mm wp Ply wood & 1mm laminate on, 50 x 50 mm (+/- 10%) Sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 Gsm FR grade synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge. (Proscenium vertical stage border facing & Side wall columns)
Providing & Fixing in position Acoustical Doors along with 150 x 75 mm teak wood frame, doors made from 50mm (+/- 10%) Teak wood frame 600 x600 c to c filled with 1000 Gsm FR grade synthetic wool 50mm thick and 3mm Tecsound from both sides, 6mm promate fire board, 12mm waterproof ply & 1 mm laminate from both sides , including 150mm heavy duty SS hinges (Geze / Dorma or eq.) 4 no each leaf, with Door-closer (Dorma / Geze or eq.) including cost of required Cut-Outs, decorative mouldings / finishing-items / melamine polish & Scaffolding as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge (Door should match 1 Hr fire rating)
Providing & Fixing in position, Acoustical Ceiling made from Gypsum Plain Panels on approved heavy duty G.I. frame ceiling channels at 450 c to c, & intermediate channels not more than 1200 c to c, along with ply wood forms suspended with Hangers from Roof, in front of 1000 Gsm FR grade synthetic wool 50 mm thick, with Paint, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge. (part of auditorium ceiling, lobby AC duct and green rooms)
Providing & Fixing in position, Acoustical Ceiling made from seamless Saint Gobain Rigitone 8/18 or Knauf Solopanel 8/18 (big panels) on approved heavy duty G.I. frame, ceiling channels at 300 c to c, & intermediate channels not more than 1200 c to c, suspended with Hangers from Roof, in front of 1000 Gsm FR grade synthetic wool 50 mm thick, with Paint, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge. (Part of auditorium ceiling)
Providing & Fixing in position, Acoustical Panelling made from 12mm thick Agro wood strips of 50, 100 & 150 mm width on 50 x 50 mm (+/- 10%) Sal-wood frame of 600 x 600 c to c having supports from wall of required length, in front of 1000 gsm FR grade synthetic wool 50 mm thick with approved coloured fabric on strips side & chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / Melamine Polish & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge. (part of auditorium walls )
Providing & Fixing in position, Carpet more than 800+ gsm, made with 100% stain proof FR grade fibres of approved make along with 5mm underlay as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge.
Providing & Fixing in position, FR grade Fabric wrapped Compressed polyester fibre nonwoven 9mm panels above the wood wool board paneling or existing frame, using adhesive, as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge. (Stage walls)
Providing & fixing in position Stage flooring Made from 18mm plywood 1200 x 2400 & 18mm Teakwood planks 100 x 800 having tongue & grove on Sal-wood frame of 50 x 100 mm (+/- 10%) at 600mm c to c on stage surface including cost of required Cut-Outs, decorative mouldings / finishing-items / polish etc., as per Architectural & Acoustical Design & Instructions & Complete in all aspects as directed by the engineer in charge.
Providing & Fixing in position, 1000 mm wide Auto-glow Aluminium extruded strips on auditorium steps as per Design & Instructions & Complete in all aspects as directed by the engineer in charge. Make Prolit or Eq
Providing & Fixing in position, Acoustical Panelling made from FR Grade Fabric wrapped Compressed polyester fibre nonwoven 9 mm panels on, 50 x 50 mm (+/- 10%) sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing-items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.including all materials labour,finishing etc complete (auditorium walls)
Providing & Fixing in position, Acoustical Ceiling made from FR Grade Compressed polyester fibre nonwoven 9mm panels on approved heavy duty GI frame 300 mm c to c & intermediate channels at 1200 mm c to c, suspended with Hangers from Roof, including cost of required Cut-Outs, decorative mouldings / finishing-items & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects including all materials labour,finishing etc complete (Stage ceiling)
Providing & Fixing in position, 12mm wp Ply wood & 1mm laminate panels above the existing wooden or fabricated frame on one side , as per Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour,finishing etc complete (Stage Pit Partation)
Providing & Fixing in position, Acoustical Panelling made from Gypsum plain 12mm panels on, 50 x 50 mm (+/- 10%) Sal-wood frame of 600 x 600 c to c having wooden supports from wall of required length, in front of 1000 Gsm synthetic wool 50 mm thick with chicken mesh on wall side, including cost of required Cut-Outs, decorative mouldings / finishing?items / paint & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. including all materials labour,finishing etc complete
Providing & Fixing in position, Under Deck insulation for metal deck using 1000 Gsm synthetic wool with fixed to deck using adhesive and chicken mesh. (Auditorium, Stage & green rooms)
Providing and Fixing Soft Fibre Acoustical Suspended Ceiling System with Optra (Bevelled Tegular) Edge Tiles of size 15mm Exposed Grid backed with 1000 GSM FR Grade Synthyetic wool 50 mm thick. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.9 - 1.0, Light Reflectance ?85%, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6 &7) in module size of 600 x 600 x 15mm , suitable for Green Building application, with Recycled content of 66% GW and 74% RW. The tile shall be laid on precoated G.I channel 32 with 15 mm wide T - section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm and 600 mm Cross Tees with a web height of 32 mm and a load carrying capacity of 7 Kilograms/M2 with a minimum pull out strength of 100 Kilograms. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system The Tile and Grid system used together should carry a 10 year warranty. The T-Grid system should be of Silhouette type with Black groove. product approved as per GRIHA and BS 476 etc. complete
Providing & Fixing in position, Providing structural steel work in trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed designs and drawings or as directed including cutting, fabricating, hoisting, erecting fixing in position, Making riveted/ bolted/ welded connection and one coat of anticorrosive paint and over it 2 coats of oil painting approved quality and shade etc. complete in all aspects as directed by the engineer in charge.
Providing & Fixing in position, Podium made from 12mm wp plywood, laminate from out side & polish inside as per given drawing & Instructions, Complete in all aspects as directed by the engineer in charge.
Providing & Fixing in position, Table made from 12mm wp plywood, laminate from out side & polish inside as per given drawing & Instructions, Complete in all aspects as directed by the engineer in charge.
Seating System
AUDIO SYSTEM
Supply installation Testing & Commissioning of below items, as per architectural & acoustical drawing/ design all complete, as directed by the engineer In-charge
Symmetrical line array speaker for Right Cluster complete with standard accessories as per the tender specifications. Vertical dispersion 85 deg horizontal 100 to 80, Bose AM serise or equivalent of L-Acoustics / Martin audio
Symmetrical line array speaker for Left Cluster complete with standard accessories as per the tender specifications. Vertical dispersion 60 deg horizontal 100 to 80 Bose AM serise or equivalent of L-Acoustics / Martin audio
Supply , installation , testing and commissioning of Flying Subwoofer complete with standard accessories as per the tender specifications Bose SMS 118 or equivalent of L-Acoustics / Martin audio
Hanging/Mounting arrangement /array frames for flying above speakers and Subwoofer including 1000 kg motorized winch complete with standard accessories as per the OEM.
Front fill loudspeakers Single 8" with bracket complete with standard accessories as per the tender specifications Bose AMU108 or equivalent of L-Acoustics / Martin Audio
Rear fill loudspeakers duel 8" with bracket complete with standard accessories as per the tender specifications Bose AMU208 or equivalent of L-Acoustics / Martin Audio
Stage monitor loudspeakers single 12" complete with standard accessories as per the tender specifications Bose AMM112 or equivalent of L-Acoustics / Martin Audio
Green room & Control Room loudspeakers complete with standard accessories as per the tender specifications Bose FS2SE or equivalent of L-Acoustics / EV
4000 W 8 Channel Networkable Power Amplifier complete with standard accessories as per the tender specifications Bose PM8500N or equivalent of L-Acoustics / Labgruppen
Supply , installation , testing and commissioning of Digital Sound Processor complete with standard accessories as per the tender specifications Bose ESP 880 A or equivalent of Biamp / Symetrix
Supply , installation , testing and commissioning of 32 Ch Mixing Console complete with standard accessories as per the tender specifications Yamaha MGP32X or equivalent of Mackie / Behringer
Supply , installation , testing and commissioning of wired handheld microphone Vocal complete with standard accessories as per the tender specifications Sennheiser E845 or equivalent of Shure/ AKG
Supply , installation , testing and commissioning of wired Instrumental microphone complete with standard accessories as per the tender specifications Sennheiser E604 or equivalent of Shure/ AKG
Supply , installation , testing and commissioning of wireless UHF handheld microphone set complete with standard accessories as per the tender specifications Sennheiser EW‐100‐G4‐835 or equivalent of Shure/ AKG
Supply , installation , testing and commissioning of wireless UHF lapel / head gear microphone set complete with standard accessories as per the tender specifications Sennheiser EW‐100‐G4‐ME2 or equivalent of Shure/ AKG
Supply , installation , testing and commissioning of gooseneck microphone with ON/OFF complete with standard accessories as per the tender specifications Sennheiser MEG14‐ 40B+MAT 133S or equivalent of Shure/ AKG
Supply , installation , testing and commissioning of Hanging microphone complete with standard accessories as per the tender specifications AKG CHM99 or equivalent of Sennheiser/ Shure
Supply , installation , testing and commissioning of Boundry microphone complete with standard accessories as per the tender specifications AKG or equivalent of Sennheiser/ Shure
Supply , installation , testing and commissioning of Antenna System complete with standard accessories as per the tender specifications Sennheiser/ Shure / AKG
Supply , installation , testing and commissioning of DVD Cum USB Player complete with standard accessories as per the tender specifications Sony/Philips/ Samsung
Supply and Fixing of Customised junction boxes complete with standard accessories as per the tender specifications.
Supply , installation , testing and commissioning of long microphone stand complete with standard accessories as per the tender specifications Ahuja/ProEL/K&M
Supply , installation , testing and commissioning of short microphone stand complete with standard accessories as per the tender specifications. Ahuja/ProEL/K&M
Supply and laying of Antenna Cable complete with standard accessories as per the tender specifications Belden or approved equivalent
Supply and laying of 2 core 4 sqmm loudspeaker cable complete with standard accessories as per the tender specifications Krystal/Parasheild or approved equivalent
Supply and Laying 2 core 2.5 sqmm loudspeaker cable complete with standard accessories as per the tender specifications Krystal/Parasheild or approved equivalent
Supply and laying of 2 core shielded microphone cable as per the tender specifications Krystal/Parasheild or approved equivalent
Supply and laying of 32 channel Snake cable as per the tender specifications Krystal/Parasheild or approved equivalent
Supply , installation , testing and commissioning of 25 mm PVC Conduit complete with standard accessories as per tender specification. AKG/Polycab/Legrand
Supply , installation , testing and commissioning of UL Listed Connectors as per the tender specifications Neutrik/Amphenol /ProEL
Supply , installation , testing and commissioning of Equipment rack of required size complete with standard accessories as per the tender specifications. Valrack/Netrack/Rittal
STAGE DRAPERY
SITC of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS Base plate Threaded rod, Black powder coated finish All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems.
SITC of C Profile MS Hot rolled strips 3mm thick with Extra U bend used either to create basic supports Customized 40 x 50mmm, All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Makes easier to suspend all the stage machinery Duly powder coated Matt black texture finish paint
functianailty for the motorised lightbars should be there with one neutral & phase connection slots and with 2 vertual load terminals. For each motor unit one each switch units should be installed inside the control panels which can be controlled with our mobiles, touch pads only with the internet connection. Motor control panel duly powder coated with ash grey paint texture finish with all required safety features
SITC of Cable Connecting Circuit Boxes for the termination of cables from Electrical panel to the grid level point made out of MS Sheet metal fabricated housing duly powder coated with matt black texture finish paint, fitted with required channels and ivery connectors, necessary glands etc.
SITC of FRLS Copper unarmoured Flexible cable IS694 having 7 Core each of 1.5 Sq mm size.
SITC of FRLS Copper unarmoured Flexible cable IS694 having 4 Core each of 4 Sq mm size.
SITC of High quality Velvet fabric fire retardant treated as per approved colour and make with a gathering of 100% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Main Curtain) Size: as per the drawing
SITC of Glazzed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 50% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For MID AND Rear Curtain) Size: as per the drawing
SITC of Glazzed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 50% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Frills) Size: as per the drawing
SITC of High quality Velvet fabric fire retardant treated as per approved colour and make with a gathering of 100% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing on to curtain trollies (For Main Valance) Size: as per the drawing.
SITC of Glazzed Cotton fabric fire retardant treated as per approved colour and make with a gathering of 0% stitched as per site condition, curtain provided with eyelets at every 200/250mm for uniform fixing. (For Wing) wing size as per the drawing
SITC of Motorised integrated Frill fly bar/winch of required length Motorized Light bar, The winch shall be provided with 01 Nos. of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y,Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG: 62052Z,IP:55, AMB:50 degree. It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5,Single Reduction 7.5:1 to 100:1 and the size shall be 90.It shall have an drive unit base frame to fix the gear box which contains one shaft. 415VAC Motor with Brake for Motor System to lift a load of 180Kg as a safe working load which should be synchronized with Control Panel. Wifi operated wireless smart working functianailty Dual barrel duly powder coated Made using 40NB dual construction.Matt black texture finish paint to keep them rust free. Powder coated 60 microns black matt finish with proper chemical treatment and methodogy. Wifi based up down lightbar movement Specially designed compact gear box 3phase AC motor with DC Brake 1.5HP. Provided with Necessary pulley, guide pulleys, GI wire rope with winding drum. Compact gear box along with suitable capacity of motor unit. Upper and lower limit controller, Safe working load of 200Kg. Cable management system.
SITC of On Stage Fixed Valance Bar of required ength Straight as per the design made out of 40NB 48 OD Mild steel pipe dual barrel, supported to hang the Main Valance of the stage system duly powder coated with matt black texture finish paint. All the materials under gone through 7 tank process with various chemical treatment to keep them rust free
SITC of Fixed Wing Structure designed as per site condition for a height approx 6.5 Mtr x 1.5 Mtr made up of MS Square tube of 25mm or higher size rested on pivotable trolley on a track for the rotation of the wing. Adjustable floor locking screw jacks with rubber grips. Inverted 4-Wheeler Trolley with Flexi Adaptor Clamp and 360° Rotatable.
SITC of Motorized DMX operated Main Curtain straight, Centre partting as per design. This mechanisam shall be provided with 01 Nos. of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. 415VAC Motor with Brake for Motor System to lift a load which should be synchronized with Motor Control centre Panel. Winch shall have 3 phase motor with an RPM of 1440,KW (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y, Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG:62052Z, IP:55, AMB:50 degree. The outer surface temperature is limited.It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5, Single Reduction 7.5:1 to 100:1 and the size shall be 90. It shall have an drive unit base frame to fix the gear box which contains one shaft Made up of I Track for complete lengthCurtain holding trollies with ball bearing for smoother noiseless movement consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of200mm /250 mm throughout the track Overlap of 0.5~0.9 Mtrs. Motor Cable termination box Trollies uniformly distributed along the track at every 200/250mm with a master trolley. Open and close limit controller.Drive unit with suitable capacity of motor unit, Wire Rope shall be of GI Wire ropes Min 3mm Dai Undergone through various chemical treatment to keep them rust free, Black texture finish paint. All metal parts are powder coated
SITC of Motorized DMX operated MID AND Rear Curtain straight, Centre partting as per design. This mechanisam shall be provided with 01 Nos. of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. 415VAC Motor with Brake for Motor System to lift a load which should be synchronized with Motor Control centre Panel. Winch shall have 3 phase motor with an RPM of 1440,KW (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y, Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG:62052Z, IP:55, AMB:50 degree.The outer surface temperature is limited.It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5, Single Reduction 7.5:1 to 100:1 and the size shall be 90. It shall have an drive unit base frame to fix the gear box which contains one shaft Made up of I Track for complete lengthCurtain holding trollies with ball bearing for smoother noiseless movement consisting of 4 wheeler master trolley and 2 wheeler trolley placed uniformly at specific interval of200mm /250 mm throughout the track Overlap of 0.5~0.9 Mtrs. Motor Cable termination box Trollies uniformly distributed along the track at every 200/250mm with a master trolley. Open and close limit controller. Drive unit with suitable capacity of motor unit, Wire Rope shall be of GI Wire ropes Min 3mm DaiUndergone through various chemical treatment to keep them rust free, Black texture finish paint. All metal parts are powder coated
SITC of Motorised integrated fly up curtain / White Screen of 12 Mtr width and 6.5 Mtr Height, The winch shall be provided with 01 Nos. of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y,Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG: 62052Z,IP:55, AMB:50 degree.
It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5,Single Reduction 7.5:1 to 100:1 and the size shall be 90.It shall have an drive unit base frame to fix the gear box which contains one shaft.This mechanisam shall have drum plate of 300mm x 5mm thickness with 6 groves where the GI wire rope of 5mm can be winded up when the hoist moves up and down. 415VAC Motor with Brake for Motor System to lift a load of 180Kg as a safe working load which should be synchronized with Control Panel. Wifi operated wireless smart working functianailty Dual barrel duly powder coated Made using 40NB dual construction.Matt black texture finish paint to keep them rust free. Powder coated 60 microns black matt finish with proper chemical treatment and methodogy. Wifi based up down lightbar movement Specially designed compact gear box 3phase AC motor with DC Brake 1.5HP. Provided with Necessary pulley, guide pulleys, GI wire rope with winding drum. Compact gear box along with suitable capacity of motor unit. Upper and lower limit controller, Safe working load of 200Kg. Cable management system.
STAGE LIGHTING
SITC of 150W High Quality LED Parcan Light complete with, Lamp source 3200K CCT Colour temperature CRI & TLCI Values above 95 COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 3 channel control Beam Angle of 9˚ / 25˚ / 35˚ Total Power Consumption of 165W High quality output replacing 1000W Halogen Par Flicker Free 100% for Tv & Film Cameras 11.7KHz Refresh Rate, Linear Dimming 0 ~ 100% Fuse and Internal safety protections Strobe option Adjustable 1~25 times/Sec Variable Fixture provided with Yoke of Manual Adjustment 5 Pin XLR for DmX , Black powder coated body. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product
SITC of 300W LED Profile Spot 19 Degree Light complete with, 3200K CCT Colour Temperature COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) CRI & TLCI above 95, Strobe option Adjustable 1 ~ 25 times / Sec 4 Kinds of dimming curves, Black finish housing, Manual Focus with 4 Beam shaping cutters Efficient and well-designed Lamp reflector Efficient Copper tube based Heat Sink for Heat Dissipation Sleek and Unique Designed Light weight body Fixture provided with Yoke of Manual Adjustment DmX 512 dimming with 1 or 3 Channel modes IP20 protection having Lux @ 3 Mtrs above 12040 suitable to illuminate the key presentor or talent on stage. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 . CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product
SITC of 300W LED RGBAL 18° to 38° Zoom Profile Spot Light complete with, COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) 3000K ~ 8000K Colour Temperature Rotary, Key, DMX control of dimmer Strobe option Adjustable 1 ~ 25 times / Sec RDM, DMX, Master-slave control mode 4 Kinds of dimming curves, Black finish housing
SITC of 400W LED Blinder Light 30 Degree complete with 3200K CCT 4x100W Chip On Board LED Lamp source COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) DmX 512 dimming with 4 /8 Channel modes CRI & TLCI Value > 90 , Strobe option Adjustable 1 ~ 25 times / Sec Variable, Beam Angle 30 Degree Total Power Consumption of 420W 11.7KHz Refresh Rate, In built preset’s for effects Fuse and Internal safety protections, Active Cooling with Low Noise Fan, 5 Pin XLR for DmX, High quality well designed inbuilt reflector, Flicker Free 100% for Tv & Film Cameras, Black finish housing, IP20 protection, Having Strobe option and smooth dimming,illuminate Stage with uniform light intensity levels.
RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory.
SITC of 200W LED Fresnel Light having COB LED source from Citizen/ Philips/ Osram/ Cree or reputed make (LM80 to be provided) 3200K colour temperature High quality uniquely designed Fresnel Lens CRI,TLCI and R9 value above 96 LED COB Based Source No Multiple Shadows – Single Source illumination Total Power Consumption of 220W Linear dimming 0 ~ 100% Adjustment Flicker Free for High FPS, Power AC90-260V, 50/60HZ Working Temperature - +40° ~ -30° Active Cooling with Low Noise Fan DmX & RDM Control options with latest technology Fixture provided with Yoke of Manual Adjustment Manual and DMX control Option mode through 5pin xlr Black powder coated fabricated housing with normal yoke. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product
SITC of 54 x 3W LED Par Light RGBW, Beam Angle 25° complete with LED source from Lumiled / Seoul / Nichia or reputed make (LM80 to be provided) RGBW 3W Lamp source x 54 Pcs DmX 512 dimming with 8 Channel High Bright Red, Green, Blue, White LED’s Source Unlimited Color Mixing through DmX 0 ~ 100% Linear dimming , In built presets for different colors Strobe Mode 20 times/Sec Data DmX through 3 / 5 Pin XLR’s 65dB ~ 130dB Sound sensing capacity Power In and Out Connections High precision colors, IP20 protection Powder coated Black finish housing Having Sound Control & Master Slave Auto Run Mode Illuminate the Indoor stage with unlimited colour effects Rigidly built pressure die-casted Aluminium body. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product
SITC of 180W LED CCT tuneable Light complete with CCT Tuneable Lamp source LED source from Lumiled / Seoul / Nichia or reputed make (LM80 to be provided) Having CRI TLCI Values above 95 High precision steady color No heat, DmX 512 dimming with 2 Channel Beam Angle 15°/ 25° / 45°
0 ~ 100% Smooth dimming, Powder coated Black finish housing Rigidly built pressure die-casted Aluminium body LED Easy view display, Flicker Free for high FPS Smooth fade in and Fade out Data DmX through 5 Pin XLR’s Total Power Consumption of 180W Sound Active Mode ControlIP20 protection. 65dB ~ 130dB Sound sensing capacity Power In and Out Connections RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 LM79 Certificates from NABL Acrediated laboratory. Brand embosed impact on the light body for genuine product
SITC of 54x3W LED 3200K Par Light Beam Angle 25° complete with , 3200K 3W Lamp source x 54 Pcs LED source from Lumiled / Seoul / Nichia or reputed make (LM80 to be provided) Having CRI TLCI Values above 95 Flicker Free for high FPS Smooth fade in and Fade out High precision steady color No heat, DmX 512 dimming with 2 Channel 0 ~ 100%, Powder coated Black finish housing Rigidly built pressure die-casted Aluminium body LED Easy view display Data DmX through 3 / 5 Pin XLR’s 65dB ~ 130dB Sound sensing capacity Power In and Out Connections Total Power Consumption of 180W Sound Active Mode Control IP20 protection. RDM Control options with latest technology (RDM ID to be specified) Certification having BIS compliant to IS 10322 (Part 5/ Sec 1):2012 CE Certification compliant to EN60598-1:2015, EN61437-2-13:2014 Brand embosed impact on the light body for genuine product
SITC of Motorized LED Moving Head Beam / Spot and Wash effect light, High bright long throw 350W Chip On Board Daylight White LED 1 Static Gobo Wheel – 10 Fixed Metal Gobos 21/26 Channel DmX Control Moto Dual Prism Mode 3
Colour Wheels – 9 Colours + CMY Motorized Zoom from 7° ~ 31°Motorized Focus and Frost, High Bright Daylight 6500K Open 7 Interchangeable Glass Gobos + Open Master Slave, Test Modes, 8 Bit/ 16 Bit High Precision Movement Sound Active and Auto Run Mode, Pan Angle 540°,Tilt Angle 270°. DmX control through 3 / 5 Pin XLR’s, IP20 rated product.
SITC of Light fixture mouting clamp Customized for suspending on fixed bars on stage Made up of Aluminium Die casted MS threaded T bolt with yellow passivation finish Complete with black powder coating matt black finish. Safe working load 150 KG Suitable to Batten of size 30 OD to 60 OD
SITC of Light Fixture dual safety, Chain made up of GI wire rope Bundled and twisted together Having load bearing capacity above 200 Kgs Sleve on the rope. Carabiner Clip
SITC of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS Base plate Threaded rod, Black powder coated finish All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems.
SITC of C Profile MS Hot rolled strips 3mm thick with Added U bend used either to create basic supports Customized 40 x 50mmm, All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Makes easier to suspend all the stage machineryDuly powder coated Matt black texture finish paint
SITC of Fixed stage side Ladder as per the design, With an Mild Steel 40NB 48 OD black matt finish. It should hang from the roof with MS anglewhich is suspended from the fish plate of 5mm. Size of 600mm x 2400mm, Manual movable Made out of 40NB 48 OD Mild steel pipe dual barrel Dual Barrel Arrangement Powder coated with Matt black Texture Single Construction with Cross connecting pipes Cross connecting Pipes at every 600mm Ladder can be moved along the track or adjusted as required, Spud & Trolley, Pivoted or Fixed Suspenders as per site conditions Round pipe welded to create square frame Heavy duty trolly to hold and rotate wing frame Single Construction with Cross connecting Pipes at every 600mm Ladder can be moved along the track Material for the light bar shall be of Mild Steel Pipe. Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Ladder Length shall be of customized type as per site condition.
SITC of Motorised integrated fly bar/winch of required length Motorized Light bar, The winch shall be provided with 01 Nos. of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y,Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG: 62052Z,IP:55, AMB:50 degree. It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5,Single Reduction 7.5:1 to 100:1 and the size shall be 90.It shall have an drive unit base frame to fix the gear box which contains one shaft.This mechanisam shall have drum plate of 300mm x 5mm thickness with 6 groves where the GI wire
rope of 5mm can be winded up when the hoist moves up and down. 415VAC Motor with Brake for Motor System to lift a load of 180Kg as a safe working load which should be synchronized with Control Panel. Wifi operated wireless smart working functianailty Dual barrel duly powder coated Made using 40NB dual construction.Matt black texture finish paint to keep them rust free. Powder coated 60 microns black matt finish with proper chemical treatment and methodogy. Wifi based up down lightbar movement Specially designed compact gear box 3phase AC motor with DC Brake 1.5HP. Provided with Necessary pulley, guide pulleys, GI wire rope with winding drum. Compact gear box along with suitable capacity of motor unit. Upper and lower limit controller, Safe working load of 200Kg. Cable management system.
SITC of Fixed FOH Lighting bar/winch of required length constructed with an dual contruction light bar with an Mild Steel 40NB 48 OD black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar.It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS anglewhich is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fastners of 10mm which can take an total load of 400KG each fastner. Made out of 48mm Outer Dai, 40 Nominal Bore Material for the light bar shall be of Mild Steel Pipe. Dual Barrel Arrangement Powder coated with Matt black Texture Fixing Through Suspenders as per site conditions Dual Construction and an additional End Caps on the Pipe end shall be there Light bar Length shall be of customized type as per site condition. Upper pipe of dual construction is used to anchor the bar lower pipe is effectively used to hang the light fixtures
SITC of Motorised integrated Utility fly bar/winch of required length Motorized Light bar, The winch shall be provided with 01 Nos. of 1.5 HP, 1440 RPM, 90 B5 frame, 3Ph. (HP) : 1.1(1.5), Frame : 90S, EFF:75.0%, MTG : B5, AMP :2.7Y,Volt:415v, DE BRG : 62052Z, DUTY:S1, FREQ:50Hz, NDE BRG: 62052Z,IP:55, AMB:50 degree. It shall have an Worm Reduction Gearbox with GMRV-90 80:1, 90B5,Single Reduction 7.5:1 to 100:1 and the size shall be 90.It shall have an drive unit base frame to fix the gear box which contains one shaft. 415VAC Motor with Brake for Motor System to lift a load of 180Kg as a safe working load which should be synchronized with Control Panel. Wifi operated wireless smart working functianailty Dual barrel duly powder coated Made using 40NB dual construction.Matt black texture finish paint to keep them rust free. Powder coated 60 microns black matt finish with proper chemical treatment and methodogy. Wifi based up down lightbar movement Specially designed compact gear box 3phase AC motor with DC Brake 1.5HP. Provided with Necessary pulley, guide pulleys, GI wire rope with winding drum. Compact gear box along with suitable capacity of motor unit. Upper and lower limit controller, Safe working load of 200Kg. Cable management system.
SITC of Power Distribution Electrical panel having a Incomer of 125 A. Floor mount / rack mount / wall mount. Miniature circuit brakers of single poles shall be fixed of different ratings from 6/10/16/25A as per the lighting fixtures.Wiring inside the module for power, control protection and instrument etc. shall be done with use of 1100 V confirming to IS 694 and IS 8130 All welding slag grounded off and welding pits wiped smooth with plumber metal.Power panels shall be designed in such a way that the internal space is sufficient for hot air movement, and the electrical component does not attain temperature more than 40 degree Celsius.Fabricated panel shall be supported with ms angles of size 25mm x 25mm with an 1.8mm thickness sheet to hold the structure. Nuetral separation made using incomer of L&T or Schneider make, Voltmeter, Ammeter display for reading visualization Individual MCB control for 52 outgoing circuits RYB Phase indicators internally wired using IS certified wires and cables Terminal for both incoming and outgoing cable shall be suitable for 1100 volts grade, aluminum/copper conductor PVC insulated and sheathed, armoured cable and shall be suitable for connections. Provided with ivery connectors for the internal terminations and external outgoing connecting points Custom built as per specification and project requirement.
SITC of High quality power junction box 4 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ) Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating Temp Moldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall / floor fixing
SITC of High quality power junction box 2 way made up of MS Sheet metal fabricated housing. Snap fit fixing /15 (1.5mm ), Total Max Rating 10A, 250V A.C 20˚C to +70˚C Operating Temp Moldings: Nylon, Flammability Rating UL94V-0 Black powder coated, fibre glands of suitable size fitted with Powercon or IEC connector Box 10A. Clamp arrangement for fixing or Raul plug arrangement for wall/floor fixing
SITC of High quality Dimming In junction box 1 way made up of MS Sheet metal fabricated housing High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Male socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing
SITC of High quality Dimming Out junction box 1 way made up of MS Sheet metal fabricated housing High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding Black powder coated, fibre glands of suitable size fitted with 5 Pin DmX XLR Female socket Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing
SITC of DmX Loop Junction Box having 1 No. of DmX 5 Pin XLR Female Socket & 1 No. DmX XLR Male Socket fitted on to a sheet metal fabricated compact Junction box powder coated with matt black texture finish paint. High temperature resistant insulator material All metal housing offers best overall RF protection & electromagnetic shielding. Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing
SITC of Internal Earthing System with copper bare conductors all along the cable trays, metal parts and Installation Hardwares
SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 150 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dessipation provided with lid.
SITC of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 75 x 40mm & 1.6 mm thickness undergone through 7 tank process with various chemical treatment to keep them rust free with perforation for heat dessipation provided with lid.
SITC of DmX Male Female Connectors 5 Pin having rubber sheeth protection for Cross connecting DmX wiring connections
SITC of DmX Male Termination Connector 5 Pin soldered with required capacity of resistor for signal deframing
DmX Touch Screen based controller having 7” Multi touch screen option 2 DmX Outlets 5 Pin XLR’s, 512 Channels each, Optically isolated outputs, 4 Smooth Encoders for control operation of attributes, Backlit keys, 12 Fader Stacks, 600+ Playbacks, 350+ Group saving, 350+ Presets, User defined shape effects, Macro saving options, External Midi timecode options, Internal clock, Shortcut user interfaces, Master fader, Blackout Key under Master fader, Numerical keypad for the light command entry inbuilt embedded within controller, USB interface, Scene saving options, Show saves and load save features, custom built user interface library for fixture files.
SITC of 76-way Power Marhalling Box made up of MS Sheet metal fabricated housing black powder coated and ivery connectors for the internal terminations and external outgoing connecting points, fibre / brass glands of suitable size.
SITC of Auxilary Marshalling Box, made up of MS Sheet metal fabricated housing black powder coated and ivery connectors for the internal terminations and external outgoing connecting points, fibre glands of suitable size.
SITC of Flat Cable Wire harness required to provide the input power to the sockets on the hoists connecting between grid level circuit box to on hoist circuit box with below specifications: FRLS Multi core Copper cable 18 Cores of Power each with 2.5 Sq. mm copper wires insulated with high insulated material 2 DmX 5 core cables with low noise Width of the flat cable 120mm approx. Clips at each bending of the cable to act as retractor unit Long life, no breakage, smooth folding
working functianailty for the motorised lightbars should be there with one neutral & phase connection slots and with 2 vertual load terminals. For each motor unit one each switch units should be installed inside the control panels which can be controlled with our mobiles, touch pads only with the internet connection. Motor control panel duly powder coated with ash grey paint texture finish with all required safety features
SITC of Cable Connecting Circuit Boxes for the termination of cables from Electrical panel to the grid level point made out of MS Sheet metal fabricated housing duly powder coated with matt black texture finish paint, fitted with required channels and ivery connectors, necessary glands etc.
SITC of FRLS Copper unarmoured Flexible cable IS694 having 3 Core each of 1.5 Sq mm size.
SITC of FRLS Copper unarmoured Flexible cable IS694 having 7 Core each of 1.5 Sq mm size.
SITC of FRLS Copper unarmoured Flexible cable IS694 having 4 Core each of 4 Sq mm size.
SITC of FRLS Copper unarmoured Flexible cable IS694 having 12 Core each of 1.5 Sq mm size.
SITC of 5 Core DmX Cable with Sheathed housing on the cable, well designed insulation, low noise suitable to transmet DmX signal.
Solar Work
Supplying, installing, testing and commissioning of 1 kWp ON-GRID Solar PV System / Plant consisting Solar PV Poly Crystalline Panel (335 Wp X 300 Nos.) and Solar ON-GRID Inverter of similar capacity (THD<3%) with interconnecting wires / cables up to solar ON GRID inverter, proper base plate, canopy box to house Inverter and necessary accessories i.e. ACDB/ DCDB , MCB etc. wiring up to solar Inverter in casing and capping, display board, sign board, two distinct earthing, lightning arrester, liaisoning charges, remote monitoring system with maintaining card / chip for 5 years including net charges for RMS System, complete up to net meter Installation and export to the grid with 5 year ON-SITE warranty and fully comprehensive maintenance contract as per Specification no. ESD-RT-ONG.
Skyway Infraprojects Pvt. Ltd.
M/s P&C Projects Pvt Ltd
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Download all tender documents and submit your bid