REPAIR REPLACEMENT OF INTERNAL WIRING, MCBs, DBs, SUB MAIN WIRING AND REPAIR TO FANS, GEYSERS IN OTM AND MD IN TECH AREA AND PINTO PARK AREA AT AF STN PALAM UNDER GE (AF) PALAM DELHI CANTT - 10

Amount

Taking down carefully unserviceable copper/aluminium point wiring (light, fan, socket or power)complete including fixture and fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings, wooden terminal boxes, plastic laminated sheet cover, including taking down of DB’s, meter board any type complete all as specified and as directed.

Material and labour for point wiring with single core PVC sheathed 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm FRLSH (Nominal area) drawn through and including non metallic rigid PVC conduit medium duty ISI marked not less than 20mm dia, with GI saddles GI screws, rawl plugs (concealed conduit/surface wiring in walls and casing capping on ceiling or roof ) including Tee, Junction boxes and provision of 3 mm thick plastic laminated sheet cover of suitable size on existing terminal boxes with new brass screws for mounting switches sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for one light/Fan/exhaust fan point controlled by one Switch. Note :- (i) Cost for cutting, chasing and making good to existing surfaces shall deemed to be included in the quoted rate.

Description all as per srl item No. 2.00 here-in-befor but for one light point controlled by two, 2- way switches complete all as specified and as directed.

Description all as per srl item No. 2.00 here-in-before but for one 3 pin 5 Amps socket out let point on the same board controlled by one switch complete all as specified and as directed.

Description all as per srl item No 2.00 here-in-before but for 3 pin 5 Amps socket out let on independent board and different wall controlled by one switch complete all as specified and as directed.

Description all as per srl item No 2.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mm stranded copper conductor cable PVC insulated FRLSH including earth wire 2.5 Sq mm copper FRLSH conductor cable connected to earth dolly complete all as specified and as directed.

Description all as per srl item No 2.00 here-in-before but for one bell/buzzer point controlled by one push button on the same board with other switches or independent with cable size 1.5 Sq mm PVC insulated stranded sheathed copper conductor complete all as specified and as directed.

Material and labour for point wiring with single core PVC sheathed 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm FRLSH (Nominal area) drawn through and including stove enamelled steel conduit medium duty ISI marked not less than 20mm dia, with GI saddles GI screws, rawl plugs (concealed conduit/surface wiring in walls ) including Tee, Junction boxes and provision of 3 mm thick plastic laminated sheet cover of suitable size on existing terminal boxes with new brass screws for mounting switches sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for one light/Fan/exhaust fan point controlled by one Switch complete all as specified and as directed. Note :- (i) Cost for cutting, chasing and making good to existing surfaces shall be deemed to be included in the quoted rate.

Description all as per srl item No .8.00 here-in-befor but for one light point controlled by two, 2- way switches complete all as specified and as directed.

Description all as per srl item No. 8.00 here-in-before but for one 3 pin 5 Amps socket out let point on the same board controlled by one switch complete all as specified and as directed.

Description all as per Srl item No 8.00 here-in-before but for 3 pin 5 Amps socket out let on independent board and different wall controlled by one switch complete all as specified and as directed.

Description all as per Srl item No 8.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mm stranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete all as specified and as directed.

Material and labour for point wiring with single core PVC sheathed 1100 volt grade cable with multi stranded copper conductor of size 1.5 Sq mm FRLSH (Nominal area) drawn through and including non metallic rigid PVC casing and capping wiring on ceiling and roof duly ISI marked including Tee, GI screw, Junction boxes and provision of 3 mm thick plastic laminated sheet cover of suitable size on existing terminal boxes with new brass screws for mounting switches sockets and regulators and drawing continuous earth wire with and including PVC sheathed 1100 Volts grade cable with stranded copper conductor of size 1.5 Sq mm (Nominal area) and connected to main earth dolly complete all as specified for one light/Fan/exhaust fan point controlled by one Switch.

Description all as per srl item No .13.00 here-in-befor but for One light point controlled by two, 2- way switches complete all as specified and as directed.

Description all as per srl item No. 13.00 here-in-before but for one 3 pin 5 Amps socket out let point on the same board controlled by one switch complete all as specified and as directed.

Description all as per srl item No 13.00 here-in-before but for 3 pin 5 Amps socket out let on independent board and different wall controlled by one switch complete all as specified and as directed.

Description all as per srl item No 13.00 here-in-before but for one power point 6 pin 15 Amps socket out let with 2.5 Sq mm stranded copper conductor cable PVC insulated including earth wire 2.5 Sq mm copper conductor cable connected to earth dolly complete all as specified and as directed.

Supply and fixing for switch piano flush type 5 Amps, single pole one way complete all as specified and as directed.

Supply and fixing for socket out let 3 pin 5 Amps, flush type complete all as specified and as directed.

S&F for switch piano flush type single pole one way 15 Amps complete all as specified and as directed.

Supply and fixing for socket outlet 2 in 1, 3 pin 5/15 Amps, flush type complete all as specified and as directed.

Supply and fixing of switch socket combination, multistranded 2 in 1, 6 and 16 Amps, flush type complete all as specified and as directed.

Supply and fixing of switch socket combination multistranded 2 in 1, 6 Amps, flush type complete all as specified and as directed.

Supply and fixing for ceiling rose, surface type, 65mm x 50mm, 2 to 3 terminal complete all as specified and as directed.

Supply and fixing electric ding dong bell, 230 volt AC, single pole complete all as specified and as directed.

Supply and fixing for electric buzzer 230 volt AC, single pole, complete all as specified and as directed.

Supply and fixing for flush type bell push, 5 Amps complete all as specified and as directed.

Supply and fixing for lamp holder, PVC/poleycarbonate type, insulated body with back plate of batten fitting complete all as specified and as directed.

Supply and fixing for stepped type fan regulator 300 watt, 230 volts, 50 HZ, AC supply complete all as specified and as directed.

S&F modular switch 1 way 6 Amps one module complete all as specified and as directed.

S&F modular switch 2 way 6 Amps one module complete all as specified and directed.

Supply and fixing of modular socket 6 Amps 2/3 Pin combined 02 module complete all as specified and directed.

S&F modular switch one way 16 Amps, one module complete all as specified and as directed.

S&F socket modular type 6 amp/16 amps, 2/3 pin combined 02 Module complete all as specified and as directed.

S&F modular fan regulator 120W, 2 Module complete all as specified and as directed.

S& F metal clad socket outlet 3 pin two phase one neutral 20A suitable for metal clad AC box complete all as specified and directed.

S& F metal clad plug top 3 pin two phase one neutral 20A suitable for metal clad AC box complete all as specified and as directed.

S&F in repait LED recessed mounting square slim LED down lighter 36 Watt for AS/GB/POP ceiling 2'x2' size complete with driver internally prewired and connecting up with twin core flexible copper conductor cable of suitable size complete all as specified and as directed.

S&F in repairs recessed type 18 W LED Panel round shape, slim, compact, auminum die cast edge lit panel with opal diffuser and separate electronic driver and including providing and connecting with twin core copper conductor twisted cable and testing on completion complete all as specified and as directed.

S&F in repairs Trim Clipon LED panel round 24W 6500K unique slimmest recess cum surface panel and including providing and connecting with twin core copper conductor twisted cable and testing on completion all as specified and as directed.

S&F in repair environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head LED luminaire 10W complete all as specified and as directed.

S&F in repair Indoor decorative LED Battens integrated type 20 watt 4 feet white 6500K fixture complete with all accessories internally pre wired and including connecting up with twin core copper conductor cable complete all as specified and directed.

S&F LED T5 Tube Rod 20 W Retro fit type complete all as specified and as directed.

S&F Indoor decorative LED Battens integrated type 10 watt 2 feet white fixture complete with driver and all accessories internally pre wired and including connecting up with twin core copper conductor cable complete all as specified and as directed.

Supply and fixing for LED bulb 12 watt fixed in pendent holder/bulk head fitting complete all as specified and as directed.

Supply and fixing for sheet metal enclosure for distribution board SPN (when MCBs to be used ) 8 way double door, 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and as directed.

Supply and fixing for sheet metal enclosure for distribution board SPN (when MCBs to be used ) 4 way double door, 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and as directed.

Supply and fixing for sheet metal enclosure for distribution board SPN (when MCBs to be used ) 12 way, double door 200 Amps rated bus bars and with neutral, earthing bar and din rail complete all as specified and as directed.

Supply and fixing for Vertical type load line distribution board, double door, 4 way, AC ,3 Phase, 415 volts ,TPN, bus bar 200 Amps rating and earth bus & din rail suitable for MCCB as incomer complete all as specified and as directed.

Supply and fixing for MCCB, 4 pole,100A ,10KA complete all as specified and as directed.

Supply and fixing for MCCB, 4 Pole 125A, 16KA complete all as specified and as directed.

Supply and fixing for MCB, 4 pole, 63A,10KA complete all as specified and as directed.

Supply and fixing for MCB, TP 63A,10KA complete all as specified and as directed.

Supply and fixing for MCB, TP 32A ,10KA complete all as specified and as directed.

Supply and fixing for MCB, SPN, 63 A ,10KA complete all as specified and as directed.

Supply and fixing for MCB, SPN, 40A ,10KA complete all as specified and as directed.

Supply and fixing for MCB, SP, 6-32A ,10KA complete all as specified and as directed.

Supply and fixing for MCB, SP, 40A ,10KA complete all as specified and as directed.

Taking down unservesiable sub main wiring with conduits/battens etc complete all as specified and as directed.

Material and labour for submain wiring with two single core 2.50 sq mm PVC insulated FRLSH multistranded copper conductor cable drawing into and including rigid non metallic PVC conduit, medium grade ISI marked with all conduit fittings & fixing accessories and one single core 2.50 Sqmm FRLSH multistranded copper conductor cable as continuous earth wire complete all as specified and as directed. Note:- Two core main wire, one core of earthing wire, PVC conduit and cutting chases shall be measured and paid as one run.

Material and labour for submain wiring with two single core 4.0 sq mm PVC insulated FRLSH multistrand copper conductor cable drawing into and including rigid non metallic PVC conduit, medium grade ISI marked with all conduit fittings & fixing accessories and one single core 4.0 Sqmm FRLSH multistranded copper conductor cable as continuous earth wire complete all as specified and directed by Engr-In-Charge. Note:- Two core main wire, one core of earthing wire, PVC conduit and cutting chases shall be measured and paid as one run.

Material and labour for submain wiring with two single core 6.0 sq mm PVC insulated FRLSH multistranded copper conductor cable drawing into and including rigid non metallic PVC conduit, medium grade ISI marked with all conduit fittings & fixing accessories and one single core 6.0 Sqmm FRLSH multistranded copper conductor cable as continuous earth wire complete all as specified and as directed. Note:- Two core main wire, one core of earthing wire, PVC conduit and cutting chases shall be measured and paid as one run.

Material and labour for submain wiring with two single core 10 sq mm PVC insulated FRLSH multistranded copper conductor cable drawing into and including rigid non metallic PVC conduit, medium grade ISI marked with all conduit fittings & fixing accessories and one single core 10 Sqmm FRLSH multistranded copper conductor cable as continuous earth wire complete all as specified and as directed by Engr-In-Charge. Note:- Two core main wire, one core of earthing wire, PVC conduit and cutting chases shall be measured and paid as one run.

Supply and fixing of sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 20 amps complete all as specified and as directed.

M&L for PVC insulated service cable flat or round sheathed, aluminium, multistranded conductor 1100V grade size 16 Sq mm 2 core complete all as specified and as directed.

Description all as per srl item No. 65.00 here-In-before but 10 Sqmm 2 core complete all as specified and as directed.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, check nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC (1:3:6) type C-1 (using 20mm graded crushed stone aggregate) with fair finish, internal surface of concrete chamber shall be given 15mm thick plaster in CM (1:4), funnel with wire gauge of 22 gauge, 8 mesh per liner inch, 80 mm thick PCC pit cover (320mm x 320mm) of RCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) reinforced with XPM, JALLI and charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) and specified including provision of earth wire protected by 15mm dia medium grade GI pipe and watering GI pipe shall be 20mm bore medium grade etc complete, all excavation and earth work & connecting the earthing to an earthing test point main switch board as specified and testing on completion complete all as specified & as directed by Engr-in-Charge.

Supply and fixing LED bldg light 45 watt IP66 with internally prewired incl electronic driver and connecting up with three core flexible copper conductor 1.5 sqmm cable complete all as specified and as directed.

M&L for GI pipe Medium grade 40mm dia bracket not less than 1.5 Mtr long and bend to a shape for fixing of bldg security light incl 02 nos MS clamps made out of (25x6)mm MS flat including 04 nos fully threated bolts and nuts fixing on wall etc complete all as specified and as directed.

Supply and fixing LED light fitting 2x16Watt flame proof, CMRI certified recommended for gas/ vapor group of group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed.

Supply and fixing of switch flame proof rotary type with termination box in LM6, 16A, single pole 250V complete all as specified and as directed.

Supply & fixing LED panel drivers suitable for 15 to 18W LED Panel with universal connector for easy installations complete all as specified and as directed.

Supply & fixing LED Adore Lamp 2.8 W Warm White B27 complete all as specified and as directed.

Supply & fixing Plug Top 16A, 3 Pin 230 Volt, AC complete all as specified and as directed.

Supply & fixing Plug Top 6A, 3 Pin 230 Volt, AC complete all as specified and as directed.

S&F for indoor decorative LED battens integrated type 20 watt 4 feet warm white 3000K fixture complete with all accessories internally pre wired and including connecting up with twin core copper conductor cable complete all as specified and as directed.

S&F, in repairs, recessed type 7W LED panel round shape, slim, compact, warm white 3000K auminum die cast edge lit panel with opal diffuser and separate electronic driver and including providing and connecting with twin core copper conductor twisted cable and testing on completion complete all as specified and directed by Engr-in-Charge.

S&F in repairs recessed type 15W LED Panel round shape, slim, compact, Warm white 3000K auminum die cast edge lit panel with opal diffuser and separate electronic driver and including providing and connecting with twin core copper conductor twisted cable and testing on completion complete all as specified and as directed.

Disconnect the electric supply and taking down carefully pre paid meter from existing position and refixing the same including S&F in replacement of Thermoplastic (Polycarbonate/Polystyrene), IP65 as per IEC 60529, corrosion proof, suitable for Meter box lid screws made of stainless steel V2A, internally embedded gasket for lid and enclosures, metric size knock outs for cable entry from top and bottom with transparent Hinged lid. DB should be able to adapt any make of MCB or din mountable equipement and tested as per as IEC 60439-3, fit for the new standard IEC 60 364-4-41, glow wire test IEC 695-2-11: 750C, flame retardant, self -extinguishing protection against mechanical load IK 08 (5 Joule) in accordance with IEC 62262 and enclosure dimension should be (217x253x115)mm (LxBxH). Makes:- Hensel cat No - KG 9003 or equivalent / Schneider meter box. Note:- Cost for cutting, chasing and making good to existing surfaces shall deemed to be included in the quoted rate.

Taking down ceiling fans of any sweep and any size including cable connections and disconnecting of fan blades and removing the fan with blades to store yard and hanging ceiling fan in its original position or any other position as per direction of Engineer-in-Charge including its fittings and fixtures after carrying out the repairs i.e cleaning, rewiding, greasing and filling, replacement of bearings, cleaning all dust and filling cavity with filler, reassembling the fan etc including testing complete all as specified and as directed by Engr-in-charge. Note :- Contractor's quoted rates shall including the following (i) Taking down fan and refixing the same position and or any other position complete with its all fittings and fixtures to make it complete functional and testing complete. (ii) Other items shall be paid under respective items as per site requirement as supply and fix in replacement i.e. rewinding, bushes, bearing, fan blade, canopy, U clamp etc.

M&L for rewinding of burnt fan motor with super enameled copper wire suitable for sweep up to 1200 mm sweep complete all as specified and as directed by Engr-in-Charge.

M&L for rewinding of burnt fan motor with super enameled copper wire suitable for sweep 1200 mm to 1400 mm sweep complete all as specified and as directed by Engr-in-Charge.

Supply and fixing in replacement of ball bearing No 6201/6202/6203/6204 suitable as per the site requirement size complete all as specified and directed by Engineer-in-Charge. Make SKF/NBC.

Supply and fixing in replacement of gun metal copper alloy bush suitable for existing make ceiling fans up to size 1400mm complete all as specified and directed by Engineer-in-Charge

Supply and fixing in replacement of GI rod, painted with white colour of size 15 mm dia and up to 1 m long suitable as per site complete all as specified and as directed by engineer-in-charge.

Supply and fixing in replacement of GI rod, painted with white colour of size 15 mm dia and up to 1.5 m long suitable as per site complete all as specified and as directed by engineer-in-charge.

Supply and fixing in replacement of ‘U’ clamps with nuts, bolts, washers and split pins complete heavy duty complete all as specified and directed by Engineer-in-Charge.

Supply and replacement of heavy duty rubber reel suitable for any size for ceiling fan. complete all as specified and directed by Engineer-in-Charge.

S&F canopy of suitable size as per the site requirement including nut and bolts complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of ceiling fan blade suitable of 1200 mm sweep size complete all as specified and directed by Engineer- in-charge.

Supply and fixing in replacement of ceiling fan blade suitable of 1400 mm sweep size complete all as specified and directed by Engineer- in-charge.

Taking down exhaust fans of any sweep and any size after taking out it from its mounting place dismantling the blades, opening the casting and cleaning the dust properly, greasing and oiling the bearing, cleaning the winding and refixing the exhaust fan to its original position or any other position including all fittings and fixture, preparation of surfaces by fillings cavity with filter and cleaning all dust after carrying out proper repairing complete all as specified and as directed. Note :- Contractor's quoted rates shall including the following:- (i) Taking down fan and refixing the same position and or any other position complete with its all fittings and fixtures to make it complete functional and testing complete. (ii) All minor repairs including greasing, oiling, prepartion of surface including filling to receiving a coat of paint . (iii) Other items shall be paid under respective items as per site requirement as supply and fix in replacement of rewinding, bushes, bearing, fan blade , canopy etc.

M&L for rewinding of exhaust fans with super enameled copper wire of suitable size up to 450 mm of any make/type/model complete all as specified and directed by Engineer-in-Charge.

Supply and fixing louvers for exhaust fan of size 300 to 450mm sweep including taking out old damaged louvers complete all as specified and as directed by Engineer-in -charge.

Supply and fixing louvers for exhaust fan of size upto 300 mm sweep including taking out old damaged louvers complete all as specified and as directed by Engineer-in -charge.

Supply and fixing fastener for Exhaust fan complete all as speified and directed by Engr-in-Charge.

Supply and fixing in replacement of exhaust fan blade of size 300mm to 450mm complete all as specified and directed by Engr-in-Charge.

Supply and fixing of plastic body exhaust fan with louvers complete 200 mm sweep, 230 volts, single phase, AC Supply complete with bolts, nuts and washers size of bolts 150 mm long, 6 mm dia embedded in the wall complete all as specified and directed by Engr-in-charge.

Supply and fixing in replacement of capacitors up to 3.15 Mfd complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement of capacitors up to 2.5 Mfd complete all as specified and directed by Engineer-in-Charge

Supply and Fixing in replacement of PVC insulated flexible multistranded copper cable of size 1.5 Sqmm, 2 core complete all as specified and as directed by Engr-in-Charge.

Taking down electric water heater/ geysers of capacity 25 ltrs from its mounting place for repair and deposit to MES complaint cell and re-fixing the same after repair and testing complete all as specified and as directed by Engr-in-charge. NOTE:- The spare items required for repair shall be measured and paid seperately.

S&F in replacement of heating element of 1.5 KW rating double tube type with cup type of circular/triangle shape including rubber washers suitable to fit in the existing geyser without any water leakage complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of heating element of 2 KW rating double tube type with cup type of circular /triangle shape including rubber washers suitable to fit in the existing geyser without any water leakage complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of the heat proof rubber PVC gasket suitable for the different make of 25 litres capacity geysers as per site requirement complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of heavy duty element holding assembly with provision for safety valve in its inlet, pocket for thermostat/ thermal cut system and drain plug suitable for 25 litres capacity geysers complete all as per site requirement and directed by Engr-in-Charge .

S&F for appretus plate (Geysers assembly) suitable for existing geysers of capacity 25 ltrs of copper/brass complete with nuts and bolts and rubber washer complete all as specified and as directed.

Supply and Fixing in replacement of vertical non return valve 15 mm dia gun metal including GI fitting such as union, nipple, elbow, socket etc as required at site complete all as specified and as directed by Engr-in-Charge.

S&F stainless steel inner tank 24 gauge heavy duty in replacement of stainless steel inner tank suitable for the existing 25 ltrs capacity geysers complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of thermostate for the geysers 25 Ltrs capacity as per site requirement complete all as specified and as directed by Engr-in-Charge .

S&F in replacement of safety valve/high pressure valve 15mm, ISI marked as per site requirement complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of the insulating material i. e. glass wool complete all as specified and as directed by Engr-in-Charge .

S&F in replacement of chromium plated copper connecting pipe 450 mm long with two brass nut and nylon washer suitable for 15mm dia pipe and connecting up complete all as specified and as directed by Engr-in-Charge .

S&F in replacement of heavy duty PVC connecting pipe with brass adapters 450 mm long suitable for 15 mm dia pipe and fixing in position complete all as specified and as directed by Engr-in-charge.

S&F in replacement of 1100 Volts grade cable flexible, 3 core PVC insulated, PVC sheathed with stranded copper conductor of size 2.5 Sqmm complete all as specified and as directed by Engr-in-charge.

S&F in replacement of single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 Amp complete all as specified and as directed by Engr–in-Charge.

S&F in replacement of top cover made of MS sheet, suitable for 25 ltrs geysers, 20 SWG duly painted with two coats of super enamel paint by spray painting complete all as specified and as directed in Engr–in-Charge.

S&F in replacement of bottom cover made of MS sheet, suitable for 25 ltrs geysers, 20 SWG duly painted with two coats of super enamel paint by spray painting complete all as specified and as directed in Engr–in-Charge.

S&F in replacement of indicating lamp red or green as per geyser suitability complete all as specified and as directed by Engr-in-Charge.

S&F in replacement of outer body made/fabricated of 22 gauge MS sheet for Geysers of 25 Litres capacity duly painted with spray paint with clamps 2 Nos of size 15mm x 3mm thick with necessary nut and bolts complete all as specified and as directed by Engr-in-Charge.

S&F in repalcement of stop cock, cast copper alloy, fancy type, long shank and cup, chromium plated, hot or cold marked , with crutch or butter fly handle, screwed down, high pressure for iron pipe/fittings or for brass ferrule, of size 15mm bore dia all as specified and directed by Engr-in-Charge.

S.R. Constructions (BID ID -3316796)

M/S R K JATOLIA ENTERPRISES (BID ID -3317123)

M/s Prakash Enterprises (BID ID -3317643)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3322746)

M/S Anand Enterprises (BID ID -3318038)

m/s rudraksh enterprises (BID ID -3317636)

ETERNITY PROJECT (BID ID -3324766)