ADDITION/ALTERATION OF SINGLE OFFRS ACCN NEAR RAJENDRA CIRCLE AND CERTAIN MINOR WORKS FOR TOILET IN ECHS, SHED IN SUB AREA OR MESS AND FIBRE SHEET IN BLDG P-622 UNDER AGE B/R -IV OF GE (SOUTH) JAIPUR

Amount

Surface excavation n exc 30cm deep and averaging 15 cm deep and getting out soft / loose soil complete all as specified and directed.Min/53 -20,Min/14 -135

M&L for excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc,or for shaft, wall, cesspits, manholes pier holes etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and as directed.Min/53 - 14, Min/01- 07, Min/14 -04, Rev/08 -20

M&L for cement concrete in foundations, filling and mass concrete type D2 (1:4:8 )using 40mm graded stone aggregate complete all as specified and as directed.Min/53 - 1.50, Min/01- 07, Min/14 -04, Rev/08 -03

M & L Brick work with subclass ' B' brick, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed. Min/53 - 09, Rev/08 -20

M &L Brickwork with sub-class `B' brick straight or curved on plan to any radius in half brick thick walls built in CM 1:4.complete all as specified and as directed. Rev/08 -12

M&L for RCC nominal mix(1:2:4) type B-1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.Min/53 - 1.20

Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, plinth beams and similar works for flat rough finished surface complete all as specified and as directed. Min/53 - 16

Use & waste of form work to sides and soffits of floor or roof beams,lintiles cantilever etc for flat rough finished surface complete all as specified and as directed. Min/53 - 12

M&L for RCC nominal mix (1:2:4) using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels & similar RCC works complete all as specified and as directed. Min/53 - 1.00

M&L for use & waste of form work to soffits of suspended slabs such as roof slabs floor slab landing and similar work for flat rough finished surface complete all as specified and as directed. Min/53 - 12

M&L for RCC nominal mix (1:2:4) using 20 mm graded stone aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like & similar RCC works complete all as specified and as directed. Min/53 - 1.50

Use & waste of form work to edges of suspended slabs n.exc 20 cm thickness for fair finished surface complete all as specified and as directed.Min/53 - 10.00

M&L rendering 15mm thick on other than fair faces of brick work or concrete surface in cement mortar 1:6 internally and finished even and fair complete all as specified and as directed. Min/53 - 14

M&L rendering 15mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 externally and finished even and fair without using extra cement complete all as specified and as directed.Min/53 - 36, Rev/08 -140

M&L rendering 10 mm thick on other than fair faces of brick work or concrete surfaces in CM 1:6 finished even and fair without using extra cement.Rev/08 -40

M&L for Cutting grooves in brick wall/stone wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and as directed. Min/53 - 10, Rev/08 -20

Returning filling in including spreading, leveling, watering and well ramming in layers n.exc 25cm thick complete all as specified and as directed. Min/53 -08.60, Rev/08 -12

Removal of excavated material n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and as directed. Min/53 - 5.20, Min/01- 07, Min/14 -24, Rev/08 -05

M&L for deformed TMT ( Fe 500 grade )bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.Min/53 - 80

M&L for steel reinforcement of TMT bars (Fe-500 Grade) 6 to 8 mm dia cut to length and bent to shape required including cranking bending spirally for hooping for columns hooking end and binding with mild steel wire ( annealed ) not less than 0.9mm dia or securing with clips complete all as specified and as directed. Min/53 - 200

All as per Ser Item No 20 above but 5 mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and as directed. Min/53 - 30

S & F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube , all as per specification and drawings complete all as specified and as directed. Min/53 - 06.00

S & F factory made solid panel PVC door shutter 30mm thick ( style) consisting of frame made out of MS tubes for top & bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap inserted for top rail & bottom rail panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed & rail with suitable PVC sheet beading, and joined together with solvent cement all as per specification & drawing. Min/53 - 03.50

S&F Steel ventilator with top hung shutter with glazing including hinges, steel peg stay complete all as specified and as directed. Min/53 - 01.00

S & F 3mm thick frosted sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and as directed. Min/53 - 0.90

S & F 200mm size aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed.Min/53 - 4.00

S & F 100mm size butt hinges medium weight, cold rolled mild steel, and fixed complete all as specified and as directed. Min/53 - 06.00

S & F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. Min/53 - 04.00

M & L Non skid cermic coloured tiles 7 to 8mm thick joint free (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match & including 15mm thick screed bed in CM 1:6 complete all as specified and as directed. Min/53 - 09.00

M & L Glazed ceramic coloured tiles in vertical surface 300 x 200 x 7mm / 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4 complete all as specified and as directed. Min/53 - 22.00

M & L preparation of newly plastered surfaces of wall and applying two coats of cement base paint over coat of primer complete all as specified and as directed. Min/53-30 , Min/01- 30

M & L preparation of newly plastered surfaces of wall and applying three coat of white wash on walls complete all as specified and as directed.Min/53-10

M&L or preparation of newly or previously untreated steel surface of any description, not otherwise described over 10cm width or girth and applying two coat of synthetic enamel paint over one coat red oxide complete all as specified and as directed. Min/53 - 02, Min/01- 33, Min/14 -42, Rev/08 -06

M&L for sand filling in floors or paving laid in layers n.exc 15 cm thick, spread, levelled and rammed including watering & well ramming complete all as specified and as directed. Min/53 - 1.30

M&L for hardcore of broken stone or boulder gauge n exc 63mm, deposited, spread and levelled in layers n exc 15cm thick watered and rammed to true surface complete all as specified and as directed. Min/53 - 1.50, Rev/08 - 04.00

M&L for 100 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate, as in sub base to floors and paving etc all complete all as specified and as directed. Min/53 - 10

M&L for 75 mm thick plain cement concrete 1:4:8 type D2, using 40 mm graded stone aggregate, as in sub base to floors and paving etc all complete all as specified and as directed. Min/14 - 135, Rev/08 - 30

M & L for 75 mm thick plain cement concrete 1:3:6, type C2, using 40 mm graded stone aggregate as in plinth protection surfaces finished even and fair without using extra cement including filling the joints by bitumen and sand mixed in the ratio 1:1 by weight complete all as specified and as directed. Min/53 - 10

M&L for Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface with or without reinforcement complete all as specified and as directed. Min/53 - 20

S&F 15 mm bore GI tubing medium grade including all fittings & fixture fixed to walls and ceilings or laid in floors complete all as specified and as directed. Min/53 - 20

S&F 20 mm bore GI tubing medium grade including all fittings & fixture fixed to walls and ceilings or laid in floors complete all as specified and as directed. Min/53 - 20

S & F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor ( Joining to be done with solvent cement ) including PVC brackets complete all as specified and as directed. Min/53 - 5, Rev/08 - 22

M & L for Concrete bed PCC 1:3;6 type C2 concrete to 110 mm pipe drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed. Min/53 - 5, Rev/08 - 22

S & F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls ( Joining to be done with solvent cement ) including PVC brackets complete all as specified and as directed. Min/53 - 03

S & F PVC (SWR) 75 mm vent cowl complete all as specified and as directed. Min/53 - 01

S & F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, laid in trenches or in floor ( Joining to be done with solvent cement ) including PVC brackets complete all as specified and as directed.Min/53 - 3, Rev/08 - 26

S & F for 75 mm dia PVC (SWR) bends any radius complete all as specified and as directed. Min/53 - 1, Rev/08 - 06

S & F 75 mm PVC (SWR) multifloor trap with grating including jointing with solvent cement complete all as specified and as directed. Min/53 - 02

M&L for 150x100mm Salt-glazed stoneware gully traps, square or round mouthed, type 'P' complete all as specified and as directed. Min/53 - 01

M&L for providing 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and as directed. Min/53 - 10

M&L for concrete bed to drain pipes type D2 1:4:8 bore of pipe 150 mm including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed. Min/53 - 10, Rev/08 - 15

S&F 20 mm Stop valves, cast copper alloy, screwed down, high pressure,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Min/53 - 01

Supply and fix cast iron P trap 100 mm complete all as specified and as directed. Min/53 - 02

S&F white vitreous china wash down water closet pan (pedestal pattern) with PVC seat cover with mild steel chromium plated or aluminised hinging device including connection to drowm pipe and flushing pipe complete all as specified and as directed. Min/53 - 01

S & F vitreous china squatting pan, 'Orissa' pattern size 580x 440mm white, with integral foot rests ( excluding flushing cistern and flush pipe ) complete all as specified and as directed. Min/53 - 01

Supply and Fixed 15mm bore angular Stop valves, Chromium plated fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Min/53 - 02

S&F PVC connections 15mm size with PTMT complete all as specified and as directed. Min/53 - 03

S&F PVC valveless 10 ltr capacity, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed. Min/53 - 02

S&F for chromium plated two way bib cock 15 mm dia, cast copper alloy with screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. Min/53 - 02

S&F Health faucet (ABS Body) with 1 meter long PVC tube & wall hook complete all as specified and as directed. Min/53 - 01

S & F Bib taps 15mm bore fancy type chromium plated long body cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule,long body complete all as specified and as directed. Min/53 - 02

Supply and fixed vitreous china wash hand basin, white of size 550mm x 400mm with pedestal including and 32mm dia brass chromium plated waste coupling and PVC waste pipe complete including angle iron brackets complete all as specified and as directed. Min/53 - 02

S&F 15 mm dia bore pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and as directed. Min/53 - 02

S&F CP fancy type soap dish holder to wall as per sample available with AGE complete all as specified and as directed. Min/53 - 02

S&F towel rail 600mm long of stainless steel chromium plated fixed with and including Chromium plated brass screws and wooden/plastic lugs/cleat complete all as specified and as directed. Min/53 - 02

S&F white vitreous china urinal full stall type of size 37.5 x 39 x 59 cm complete including providing and fixing plugs,bedding urinal against wall in cement mortar 1:2 securing to plugs with and including 60 mm long brass screws pointing around urinal back in white cement complete all as specified and as directed. Hindware cat Part No 60002 or any other equivalent make as per Appx B. Min/53 - 01

S&F 32 mm dia LDPE pipe of pressure rating 6 kgf/cm2 fixed complete to wall ,ceiling or floors including all fittings complete all as specified and as directed. Min/53 - 01

M&L for Granite stone slab 15 to 18 mm thick (table rubbed and polished) in Partition including pointing in coloured cement (1:2) using marble dust with admixture of pigment to match with granite shade complete all as specified and as directed. Min/53 - 01

S&F urinal spreader of brass chromium plated suitable for 15mm dia pipe complete all as specified and as directed. Min/53 - 01

Cutting into existing manholes/ septic tank for connecting new drains making good to pipe and rendering , cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete 1:2:4, type B-1, smooth finished and reforming benching as required for 150mm bore pipe complete all as specified and as directed. Min/53 - 01

M&L for preparation of plastered surface of wall and applying two coats of oil bound distemper over a coat of primer after applying 1 mm thick wall care putty to make the surface even and smooth complete all as specified and as directed. Rev/08 - 40

M&L for providing precast cement concrete type B-0, 1:2:4 (12.50mm graded aggregate) as in louvers and jallies (any size and shape),45mm thick (measured solid) including all moulding but excluding frame set in CM 1:4 complete all as specified and as directed. Min/01 - 15

S&F mild steel works as in fencing posts/flat iron as in straps to hold chain link fencing incl cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing wire mesh etc) incl necessary drilling bolting or reveting etc and similar work complete all as specified and as directed. Min/01 - 510

S&F for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachement conforming to Fe 410W (Gde E-250) quality A and including necessary welding as per site rqeuirement complete all as specified and as directed. Min/14- 75

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 and necessary welding as per site requirement complete all as specified and as directed. Min/14-1055, Rev/08-350

Supply & Fix mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut 10 to 12 mm dia and exc 5 cm and nexc 10 cm long complete all as specified and as directed. Min/01-13, Min/14 - 09

S&F 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugations side lap fixed with coach screw and washer in roof, wall etc sheet of any colour complete all as specified and as directed. Min/01 - 192

S&F rubber moulded decorative designed coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment laid over and including 25 mm thick fine sand coushion including rolling /compacting the finished surface complete all as specified and directed. Min/14 -135

M&L Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. Min/14 - 135, Rev/08 - 50

M&L providing pre cast cement concrete block or slab 150mm thick 1:2:4 type B1 using 20mm graded stone aggregate with plain or inter locking joints as directed set in CM 1:6. as in kerb/edge block to hard standing/footh including necessary earth work complete all as specified and as directed. Min/14 - 1.50

M&L for fibre reinforced 12 mm thick for seamless false ceiling of grid size 60 cm x 60 cm fixed with screw over and including Gl frame work comprising of Gl perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete as per manufacturer instruction complete all as specified and as directed. Rev/08 - 80

M&L for preparation of new plastered surfaces of walls and applying two coats of Acrylic emulsion (exterior weather coat) paint of any tint as approved over one coat of primer applied as per manufacturer's instruction complete all as specified and directed by Engineer-in-Charge. Rev/08 - 140

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for doors with one or more rebates including necessary fixing lugs, 100mm MS hinges ,lock strike plate, etc complete all as specified and as directed. (Note: 100mm MS hinges shall be provided as fixed with frame 6 nos as per requirement and shall be deemed to be included in quoted rate. Rev/08 - 40

S & F 35mm thick factory made plain, framed, paneled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formal dehyde resin adhesive confirming to IS-710. The size of rails & style shall be as per IS-1003 complete all as specified and as directed. Rev/08 - 14

M&L for preparing new wooden surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed. Rev/08 - 30

S & F 200mm Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed. Rev/08 - 24

S & F 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed. Rev/08 - 24

Labour only for cleaning earthwork under item No 2 and filling in floors or paving laid in layers n.exc 15 cm thick, spread, leveled and rammed including watering & well ramming complete all as specified and as directed. (Note:- Usable sand obtained from Serial item No 2 shall be used under this item) Rev/08 - 03

S&F light shade vitrified ceramic tiles double charged edge cut 10mm thick ( square/ rectangular ) polished, area of each tiles not exceeding 0.36 sqm in floor etc set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 15mm thick screed bed in CM (1:6) complete all as specified and as directed. Rev/08 - 50

All as per Ser item No 90 above but as in skirting/ vertical surface over & including 10mm thick rendering in CM (1:4) on stone/brick masonary surface complete all as specified and as directed. Rev/08 - 03

M & L for glazed digital printed ceramic coloured tiles in vertical surface 350 x 250 x 7mm / 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10mm thick rendering on stone masonary surface or surface other than fair faces of brick work in CM 1:4 complete all as specified and as directed. Rev/08 - 150

M & L of 20 mm thick Granite (of any type) work (table rubbed and polished) in kitchen Slab,steps, jambs, pillars, window cills and all horizontal portion and like in 15 mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. Rev/08 - 24

M & L 20 mm thick Granite (of any type) work (table rubbed and polished) for wall (veneering to wall) and any vertical surface etc with 12mm thick cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. Rev/08 - 04

M&L 20 to 25mm thick kota stone slab for kitchen slab including rubbing polishing fixing complete all as specified and as directed. Rev/08 - 24

S&F of PVC Nahani / floor trap and square in size of 100 x 100mm including MS chromium plated grating 125mm dia of weight not less than 50gm for floor trap/ Nahani trap complete all as specified and as directed. Rev/08 - 13

S&F sink mixer 15mm bore cast coper alloy CP fancy type, with crutch or butterfly handle, screwed down, screwed for iron pipe or for union for kitchen complete all as specified and as directed. Rev/08 - 13

Supply & laying 16mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 with all fittings and fixed complete to walls & ceiling or laid in floors or concealed in walls etc complete all as specified and as directed. Rev/08 - 120

S&F in repair stainless steel sink with drainage board 1.00 mm thick (SS grade 304 AISI 18/8) IS embosed (IS:13983) for kitchen or laboratory, with plug, washers, waste pipe including bedding in cement mortar on to draft wall or including fixing cantilever brackets, connecting union to pipe etc, overall size 915 mm x 460 mm, with bowl size 410 mm x 330 mm x 160 mm with including waste coupling, waste pipe complete all as specified and as directed. Rev/08 - 13

Supply fabricate & fix in position aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) three track window ( two shutters glazed & one shutters wire gauge) with frame, glazed with 4 mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below, including taking down old window complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50 mm ( Section No 20832) (c) Top & side Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 mm (Section No 20738) (d) Shutter Interlock Section shall be be of size 18.00 x 40.00 x 1.45 mm (Section No 20737) (e) Bottom Members of shutter Section shall be be of size 18.00 x 40.00 x 1.55 mm (Section No 20736) Note:-Section No given above are of make Jindal, Contractor may use similar section of other make mention in Appx B. Rev/08 - 10

S &F Framed work such as grills, gratings, etc., with ends of bar shouldered or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks with angle, MS sheet Flat iron & similar work conforming to Fe 290 GDE -E-165 , framed and hung as in gates incl pintol hinges , stops, hand made sliding bolts etc and for ornamental and intricate design. Rev/08 - 170

Supply & Fixing for steel water tubing, galvanised, medium grade, with all fittings and fixed complete to walls & ceiling or laid in floors or concealed in walls etc of size of tubing 25 mm bore complete all as specified and as directed. Rev/08 - 16

S&F stainless steel grating 100 mm dia including fixing in cement mortar 1:4 complete all as specified and as directed. Rev/08 - 13

Demolition Brickwork of stone/boulder masonry, build in cement mortar or cement lime mortar including all quoins, arches, pillars etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed. Rev/08 - 02

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed. Rev/08 - 08

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joint fixed to walls complete all as specified and as directed. Rev/08 - 18

S&F PVC (SWR) pipes 110mm fittings bend complete all as specified and as directed. Rev/08 - 04

M&L for providing 150 mm dia Reinforced concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and as directed. Rev/08 - 15

S&F 500 litres capacity triple layer, white coloured rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed. Min/53 - 01, Rev/08 - 01

S&F1000 litres capacity triple layer, white coloured rotational molded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 25 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and as directed. Rev/08 - 03

M&L for point wiring with 1100 volts grade PVC insulatd FRLS multistranded copper conductor cable 1.5 Sqmm (Phase-Red, Neutral-Black) and earth continuity conductor 1.5 Sqmm (Green) drawn into non metallic rigid concealed PVC conduit not less than 20 mm ISI marked ivory colour with all fittings/fixing accessories and unwelded sunken galvnised pressed steel terminal boxes of thickness not less than 1.0 mm covered with 3mm thick phenlic laminated white sheet cover for mounting sheet cover for mounting switches, sockets, fan regulators for one light point controlled by one switch. Min/53-06, Rev/08 - 26

One light/fan/ exhaust fan point controlled by one switch. Min/53-01, Rev/08 - 13

One socket outlet 6 Amps controllled be one switch on the same board with other switches Min/53-01, Rev/08 - 13

One socket outlet 6 Amps controlled by one switch on independent board. Min/53-01, Rev/08 - 13

S&F angle holder 6 Amp, 240 V insulated polycarbonate body with back plate complete all as specified and as directed. Min/53-01

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and terminated in modular metal flush boxes with modular white cover plate with frame for one socket point 16 Amps controlled by one switch on indepdendent board. Min/53-01, Rev/08 - 26

S&F switch modular 1 way 6/10 Amps, 230 volts, 1 module complete all as specified and as directed. Min/53-10, Rev/08 - 65

S&F modular socket 6/10 Amps, 2/3 Pin combined 1 modules AC 230 Volts. Min/53-02, Rev/08 - 26

S&F switch modular 1 way 16/20 Amps, 230 volts, 1 module complete all as specified and as directed. Min/53-01, Rev/08 - 26

S&F modular socket 16/20 Amps, 2/3 Pin combined 2 module AC 230 Volts. Min/53-01, Rev/08 - 26

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FRLS multistranded copper cable of size 2 x 6 Sqmm drawing into and including rigid non metallic PVC conduit concealed in wall, medium grade not less than 20mm dia ISI marked ivory colour with all conduit fitting and fixing accessories and 6 Sqmm FRLS multistranded copper condutor cable as continuous earth wire complete all as speciifed and directed (Note 1 :- 2 runs of 6 Sqmm copper wire and 1 run of 6 Sqmm copper earth wire alongwith PVC conduit shall be measured as 1 unit. Note 2 - Rate of cutting chasing of existing wall and making good of disturbed surface for concealed conduit shall be included in this item). Rev/08 - 120

S&F MCB distribution board, powder coated, CRCA steel sheet, degree of protection IP 43, IK-09 with reversible double door, recess mounted , having insulated 200 Amps tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required complete all as specified and as directed. Min/53-01, Rev/08 - 02

S&F MCBs of 'C' series single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete. Make : Legrand Cat Ref No. 508587 to 408595 and equivalent cat part in other makes as per Appendix 'B'. Min/53-06, Rev/08 - 12

S&F MCBs of 'C' series double pole 10 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete. Make : Legrand Cat Ref No. 408631 to to 408637 and equivalent cat part in other makes as per Appendix 'B'. Min/53-01, Rev/08 - 02

S&F LED (1.2M) smartbrite extra batten made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2500 lumens/22 watt at a minimum system efficacy of 4000 lumen per 22 watt and total power consumption not more than 40 watt including driver. It has a rated system life time of 25000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete. Philips Cat Part No : BN 021LED 25S 6500 PSU GR S1 and equivalent cat part in other makes as per Appendix 'B'. Min/53-02, Rev/08 - 13

S&F LED fixture 10 watt having lumen output 100 lumens per watt including connection.Philips Cat Part No : BN 021LED 25S 6500 PSU GR S1 and equivalent cat part in other makes as per Appendix 'B'. Min/53-01, Rev/08 - 13

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed. Min/53-01, Rev/08 - 13

S&F 10 watt LED T -lamp B-22 base (warm white/golden yellow) 1000 lumens, Make : Make : Philips Cat Part No 9290018611 or equivalent cat part in other makes as per Appendix 'B'. Min/53-01

M & L for Supplying, laying, connecting and testing in trenches, under floors/ roads or on walls Cable XLPE insulated screened PVC bedded galvanized steel strips or wire armored, electric power cables (heavy duty) ISI marked with stranded aluminium conductor earthed, 1100 volts grade, of 16 Sqmm 2 core complete all as specified and directed. Min/53 - 40

M&L sand cushioning (Tibba sand) to PVC under ground cable with screened and washed sand and punning to provide a required cover complete all as specified and as directed. Min/53 - 03

M & L Bricks for protection cover to under ground cable (with old size sub class ‘B’ bricks) with width equal to length of brick laid dry and flat abutting each other with gaps between adjacent brick not exceeding 10 mm as directed by Engineer-in-Charge. Min/53 - 0.32

S&F LED Street Light of 30 W with complete fitting including bracket nut bolt fastners fixed on pole/wall complete all as specified and as directed. (Make Phillips Smart Bright 6500K BRP046 LED 30CW MR51PSUGR Min/53 - 01

ANKIT BUILDERS

MSR INFRATECH

S.R.Enterprises