Turnkey Contract for LT Network Renovation and Augmentation Pkg3 Lot4 (PCE-3-Pakyong District)

Schedule A1 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Non-Sealed Type) - 750 kVA, 500 kVA, 315 KVA, 250 KVA

DISTRIBUTION TRANSFORMER (NON-SEALED TYPE), 11/ 0.433 KV, Dyn 11, Copper Wound (3 phase), ONAN COOLED, OUT-DOOR TYPE WITH OFF-CIRCUIT TAPPINGS OF +5% TO -10% IN STEPS OF 2.5% ON H.V SIDE, PROVIDED WITH STANDARD FITTINGS & ACCESSORIES WITH FIRST FILLING OF TRANSFORMER OIL CONFORMING TO IS:1180 (PART-I)2014 : ENERGY EFFICIENCY LEVEL -2

INCOMING:- 1 No. 1000 Amp, 415 Volt, 50 KA, FP, Draw Out type ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 400 Amp TP MCCB breaking capacity 35 KA, 1 No. 100 Amp TP MCCB breaking capacity 35 KA & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA all with built in Thermo Magnetic Release

INCOMING:- No. 800 Amp, 415 Volt, FP, manually Draw Out type ACB with in built Thermo Magnetic Release & 6No+6Nc Auxiliary contacts. Outgoing:- 3 Nos. 200 Amp TP MCCB breaking capacity 35 KA , 1 No. 100 Amp TP MCCB breaking capacity 35 KA & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA, all with built in Thermo Magnetic Release

INCOMING: 1 No. 630 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 200A TP MCCB, 50 KA & 1 No. 63A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 400 A, 4P,50KA, MCCB OUTGOING: 1 No. 200A TP MCCB, 50 KA ,2 Nos. 100A TP MCCB, 35 KA & 1 No. 63A TP MCCB, 35 KA, all with built in Thermo Magnetic Release.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

11 kV, 3 X 35 sq.mm Cu / XPLE Cable

Heat Shrinkable Outdoor type end termination kit for 11 KV (E) 3 core XLPE (Kit No.EOKT 3091-3131) Raychem make or equivalent : 3 C X 35 sqmm

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

Back clamps of 50x8mm G.I. flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III) Raychem RPG make or equivalent

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 25x6 mm. for earthing

1.1 kV 1Cx240 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer) (2 cables /cct for 750 / 500 KVA, 1 cable/cct for 315/250 KVA)

Tinned Copper Lugs - 240 sqmm

AAAC Rabbit Conductor (for down wires)

Al Line Tap / PG Clamp, Double Bolt, 25-150 sqmm

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Mandatory Spare Parts

Spare Fuse element tubes for DOF of 750 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 500 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 315 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 250 KVA Distribution Transformer

Schedule A2 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Hermetically Sealead) - 100 kVA, 63 kVA, 25 KVA

DISTRIBUTION TRANSFORMER (SEALED TYPE), 11/ 0.433 KV, 50 Hz, Dyn 11, Copper Wound (3 phase), ONAN COOLED, OUT-DOOR TYPE (WITH OFF-CIRCUIT TAPPINGS +2.5% TO -5% IN STEPS OF 2.5% ON H.V SIDE) PROVIDED WITH STANDARD FITTINGS & ACCESSORIES OIL FILLED AND HERMETICALLY SEALED CONFORMING TO IS:1180 (PART-I) 2014: ENERGY EFFICIENCY LEVEL -2

INCOMING: 1 No. 200 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 100A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 100 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 63A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 63 A, 4P,50KA, MCCB OUTGOING: 2 Nos. 40A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole 200 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

11 KV, 3 Pole, 200 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

G.I. channel 75 X 40x4.8mm X 1.2 m long for mounting of DT

Back clamps of 50x8mm G.I. flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III)

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

GI strip 25x6 mm. for earthing

1.1 kV 1Cx50 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer)

Tinned Copper Lugs - 50 sqmm

AAAC Rabbit Conductor (or down wires)

Al Line Tap / PG Clamp, Double Bolt, 25-150 sqmm

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Mandatory Spare Parts

Spare Fuse element tubes for DOF of 100 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 63 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 25 KVA Distribution Transformer

Schedule A3 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Dry Type / Outdoor) - 500 kVA, 250 kVA, 100 KVA

DISTRIBUTION TRANSFORMER (DRY TYPE), 11/ 0.433 KV, 50 Hz, Dyn 11, Copper Wound (3 phase), OUTDOOR TYPE, (WITH OFF-CIRCUIT TAPPINGS ON H.V SIDE) PROVIDED WITH STANDARD FITTINGS & ACCESSORIES CONFORMING TO IS:11171 & 2026

INCOMING:- 1 No. 800 Amp, 415 Volt, FP, manually Draw Out type ACB with in built Thermo Magnetic Release & 6No+6Nc Auxiliary contacts. OUTGOING:- 3 Nos. 200 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release

INCOMING : 1 Nos. 400 Amp,415V, FP MCCB breaking capacity 50 KA with built in Thermo Magnetic Release, OUTGOING : 1 Nos. 200 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 3 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release.

INCOMING:- 1 Nos. 200 Amp,415V, FP MCCB breaking capacity 50 KA with built in Thermo Magnetic Release. OUTGOING:- 2 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release & 1 No. 32 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release having Relay setting 16-25A.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

3 X 35 sq.mm 11 KV Cu / XPLE Cable

Heat Shrinkable Outdoor type end termination kit for 11 KV (E) 3 core XLPE (Kit No.EOKT 3091-3131) Raychem make or equivalent : 3 C X 35 sqmm

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

Back clamps of 50x8mm G.I.flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III)

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 35x6 mm. for earthing

1.1 kV 1Cx150 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer) (2 cables / cct for 500 kVA)

Tinned Copper Lugs - 50 sqmm

AAAC Rabbit Conductor

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Mandatory Spare Parts

Spare Fuse element tubes for DOF of 500 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 250 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 100 KVA Distribution Transformer

Schedule B : Schedule of Quantities for 11/0.433 kV Packaged Substation - 750 kVA, 500 kVA

Packaged sub-station 11/0.433 KV, 50 Hz consisting of 11 kV, 3 way SF6 insulated compact RMU, oil cooled (Aluminium wound)/ dry type copper wound transformer and LT section with one ACB as incoming and 4 nos outgoing MCCB feeders and with encloser made of electromechanically galvanized

11 kV RMU - 2 X 630 A LBS + 1 X 200 A VCB (Motor Operated / SCADA ready ) 750 KVA Oil cooled (Al wound) / Dry Type (Cu wound) transformer LT Compartment : INCOMING:- 1 No. 1000 Amp, 415 Volt, 50 KA, FP, ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 400 Amp + 1x100 Amp + 1x63 Amp, TP MCCBs breaking capacity 35 KA with built in Thermo Magnetic Release

11 kV RMU - 2 X 630 A LBS + 1 X 200 A VCB (Motor Operated / SCADA ready ) 500 KVA Oil cooled (Al wound) / Dry Type (Cu wound) transformer LT Compartment : INCOMING:- 1 No. 800 Amp, 415 Volt, 50 KA, FP, ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 200 Amp + 1x100 Amp + 1x63 Amp, TP MCCBs breaking capacity 35 KA with built in Thermo Magnetic Release

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 25x6 mm. for earthing

Schedule C : Schedule of Quantities for Low Voltage OH Lines

8.5 mtr. steel latticed structure of 35x35x6 mm complete with nuts & bolts.

LT shackle insulator 3"x3 1/2".

D-clamp complete with G.I. pin, washers, nuts & bolts.

Guy assembly complete with 7/12 SWG GI stay wire, 110x75 mm LT guy insulator, 16mm dia stay rod,1.8 mtrs. long with bow thimble, turn buckle and 150x150x6mm anchor plate, GI stay clamp for lattice structure

AAC ANT conductor 50 sq.mm.

AAC GNAT conductor 25 sq.mm.

No. 12 SWG G.I wire for continuous earth wire

Al Binding Wire 10 SWG

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 304350 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

Danger Board 440 Volts.

Red Oxide paint @1.5 Ltr./pole.

Aluminium paint @1 Ltr./pole.

G.I Barbed wire @ 2Kg/pole.

Schedule D : Schedule of Quantities for Low Voltage UG cable lines

1.1 kV grade armoured cable (Al Conductor/XLPE Insulated/SWA/PVC Sheathed)

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

3.5 core x 35 sq.mm.

3.5 core x 25 sq.mm.

4 core x 16 sq.mm.

2 core x 16 sq.mm.

2 core x 10 sq.mm.

Rigid U PVC pipe as per IS 4985-2000 working pressure 6Kgf/cm2

160 mm dia.

110 mm dia.

75 mm dia.

50 mm dia.

1.1 KV indoor/outdoor end termination kit suitable for:

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

3.5 core x 35 sq.mm.

3.5 core x 25 sq.mm.

1.1 KV straight through jointing kit suitable for:

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

FEEDER PILLARS: OUTDOOR TYPE CUBICLE CONFORMING TO IS:8623-1 Main Feeder Panel: Cubicle design totally enclosed and water proof outdoor type floor mounted suitable for use in 440 V,400A as main feeder pillar Incomer : 1 No 400 A, MCCB, 50KA Outgoing: 2 Nos. 200 A TPN MCCB & 4 Nos. 32 A TPN, MCB for individual service connections.

FEEDER PILLARS: OUTDOOR TYPE CUBICLE CONFORMING TO IS:8623-1 Sub-Main Feeder Panel: Cubicle design totally enclo.& water proof outdoor type floor mounted suitable for use in 440V 200 A as a sub-main feeder pillar: Incomer: 1 No. 200 A, TPN MCCB Outgoing: 3 Nos. 63 A TPN MCCB & 4 Nos. 32 A MCCB for individual service connections & 8 Nos.16 A TPN for individual service

Safe earthing electrode Model T-19 short time current 20 KA rms for 1 sec (MV) application: 50 mm dia.x3 mtrs. electrode & 2 bags backfill Chemical compound .

GI strip 25mm X 5mm for earthing

Aluminium thimble of size;

Sundry itmes for 3.5C x 25 or 35 / 4C x 16 sqmm cable line installation for upto 30 Nos 3-phase connections for termination at switchgear / meterboxes ( like nails, saddle, etc.)

Sundry itmes for 4C x 16 / 2Cx 16 & 10 sqmm cable line installation for upto 50 Nos 1-phase & 3-phase connections for termination at switchgear / meterboxes ( like nails, saddle, etc.)

Schedule E : Schedule of Quantities for Low Voltage ABC lines

8.5 Mtr STP 410 SP21 complete with base plate, nuts & bolts

Tension / Dead End Clamp with hook attachment for AB Cable with insulated messenger, 50-70 sqmm, 20 kN breaking load

Tension / Dead End Clamp with hook attachment for AB Cable with insulated messenger, 25-35 sqmm, 20 kN breaking load

Suspension Clamp with hook attachment for AB Cable with insulated messenger, 25-95 sqmm, 16 kN breaking load

GI Pole Clamp for fixting hook attachment on STP pole

Piercing Connector TYPE -I, (Main 25-120 sqmm Tap Off 25-120 Sqmm)

Piercing Connector TYPE -II, (Main 35 -120 sqmm Tap Off 16-25 Sqmm) (provisional qty for st. lighting tapping)

1.1 kV XLPE Aerial Bunched Cable 3x120+1x70+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x95+1x70 +1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x70+1x50+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x50+1x35+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x35+1x35+1x16 sqmm, insulated neutral cum Messenger

Stay set including 16 mm Dia x 1.8 mtr Long Rod, and 110 x 75 x 6 mm Anchor Plate complete with 7/12 SWG Stay Wire, G.I Stay clamp

G.I. Back Clamps 75 x 8 mm flat complete with G.I Pole Clamp

Earthing Coil of 115 Turns of 50 MM Dia and 2.5 Mtr Lead of 4.0 mm G.I Wire

Push on type end caps for ABC, 16-120 sqmm

Three phase LT ABC Distribution Box with Spring Loaded Busbar System suitable for 1 Incoming 3 Outgoing 3 Phase Circuits

Single phase LT ABC Distribution Box Spring Loaded Busbar System suitable for 1 Incoming 6 Outgoing 1 Phase Circuit

4C x35 sqmm Al/PVC cable for connecting Dist. Box to ABC

2C x25 sqmm Al/PVC cable for connecting Dist. Box to ABC

Red Oxide Paint

Aluminium Paint

Anti Climbing Device (Barbed Wire)

440 Volt Caution Board

Description of Work / Item(s)

Amount

Schedule A1 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Non-Sealed Type) - 750 kVA, 500 kVA, 315 KVA, 250 KVA

DISTRIBUTION TRANSFORMER (NON-SEALED TYPE), 11/ 0.433 KV, Dyn 11, Copper Wound (3 phase), ONAN COOLED, OUT-DOOR TYPE WITH OFF-CIRCUIT TAPPINGS OF +5% TO -10% IN STEPS OF 2.5% ON H.V SIDE, PROVIDED WITH STANDARD FITTINGS & ACCESSORIES WITH FIRST FILLING OF TRANSFORMER OIL CONFORMING TO IS:1180 (PART-I)2014 : ENERGY EFFICIENCY LEVEL -2

INCOMING:- 1 No. 1000 Amp, 415 Volt, 50 KA, FP, Draw Out type ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 400 Amp TP MCCB breaking capacity 35 KA, 1 No. 100 Amp TP MCCB breaking capacity 35 KA & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA all with built in Thermo Magnetic Release

INCOMING:- No. 800 Amp, 415 Volt, FP, manually Draw Out type ACB with in built Thermo Magnetic Release & 6No+6Nc Auxiliary contacts. Outgoing:- 3 Nos. 200 Amp TP MCCB breaking capacity 35 KA , 1 No. 100 Amp TP MCCB breaking capacity 35 KA & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA, all with built in Thermo Magnetic Release

INCOMING: 1 No. 630 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 200A TP MCCB, 50 KA & 1 No. 63A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 400 A, 4P,50KA, MCCB OUTGOING: 1 No. 200A TP MCCB, 50 KA ,2 Nos. 100A TP MCCB, 35 KA & 1 No. 63A TP MCCB, 35 KA, all with built in Thermo Magnetic Release.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

11 kV, 3 X 35 sq.mm Cu / XPLE Cable

Heat Shrinkable Outdoor type end termination kit for 11 KV (E) 3 core XLPE (Kit No.EOKT 3091-3131) Raychem make or equivalent : 3 C X 35 sqmm

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

Back clamps of 50x8mm G.I. flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III) Raychem RPG make or equivalent

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 25x6 mm. for earthing

1.1 kV 1Cx240 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer) (2 cables /cct for 750 / 500 KVA, 1 cable/cct for 315/250 KVA)

Tinned Copper Lugs - 240 sqmm

AAAC Rabbit Conductor (for down wires)

Al Line Tap / PG Clamp, Double Bolt, 25-150 sqmm

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Mandatory Spare Parts

Spare Fuse element tubes for DOF of 750 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 500 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 315 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 250 KVA Distribution Transformer

Schedule A2 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Hermetically Sealead) - 100 kVA, 63 kVA, 25 KVA

DISTRIBUTION TRANSFORMER (SEALED TYPE), 11/ 0.433 KV, 50 Hz, Dyn 11, Copper Wound (3 phase), ONAN COOLED, OUT-DOOR TYPE (WITH OFF-CIRCUIT TAPPINGS +2.5% TO -5% IN STEPS OF 2.5% ON H.V SIDE) PROVIDED WITH STANDARD FITTINGS & ACCESSORIES OIL FILLED AND HERMETICALLY SEALED CONFORMING TO IS:1180 (PART-I) 2014: ENERGY EFFICIENCY LEVEL -2

INCOMING: 1 No. 200 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 100A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 100 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 63A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 63 A, 4P,50KA, MCCB OUTGOING: 2 Nos. 40A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole 200 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

11 KV, 3 Pole, 200 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

G.I. channel 75 X 40x4.8mm X 1.2 m long for mounting of DT

Back clamps of 50x8mm G.I. flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III)

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

GI strip 25x6 mm. for earthing

1.1 kV 1Cx50 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer)

Tinned Copper Lugs - 50 sqmm

AAAC Rabbit Conductor (or down wires)

Al Line Tap / PG Clamp, Double Bolt, 25-150 sqmm

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Mandatory Spare Parts

Spare Fuse element tubes for DOF of 100 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 63 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 25 KVA Distribution Transformer

Schedule A3 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Dry Type / Outdoor) - 500 kVA, 250 kVA, 100 KVA

DISTRIBUTION TRANSFORMER (DRY TYPE), 11/ 0.433 KV, 50 Hz, Dyn 11, Copper Wound (3 phase), OUTDOOR TYPE, (WITH OFF-CIRCUIT TAPPINGS ON H.V SIDE) PROVIDED WITH STANDARD FITTINGS & ACCESSORIES CONFORMING TO IS:11171 & 2026

INCOMING:- 1 No. 800 Amp, 415 Volt, FP, manually Draw Out type ACB with in built Thermo Magnetic Release & 6No+6Nc Auxiliary contacts. OUTGOING:- 3 Nos. 200 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release

INCOMING : 1 Nos. 400 Amp,415V, FP MCCB breaking capacity 50 KA with built in Thermo Magnetic Release, OUTGOING : 1 Nos. 200 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 3 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release.

INCOMING:- 1 Nos. 200 Amp,415V, FP MCCB breaking capacity 50 KA with built in Thermo Magnetic Release. OUTGOING:- 2 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release & 1 No. 32 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release having Relay setting 16-25A.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

3 X 35 sq.mm 11 KV Cu / XPLE Cable

Heat Shrinkable Outdoor type end termination kit for 11 KV (E) 3 core XLPE (Kit No.EOKT 3091-3131) Raychem make or equivalent : 3 C X 35 sqmm

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

Back clamps of 50x8mm G.I.flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III)

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 35x6 mm. for earthing

1.1 kV 1Cx150 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer) (2 cables / cct for 500 kVA)

Tinned Copper Lugs - 50 sqmm

AAAC Rabbit Conductor

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Mandatory Spare Parts

Spare Fuse element tubes for DOF of 500 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 250 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 100 KVA Distribution Transformer

Schedule B : Schedule of Quantities for 11/0.433 kV Packaged Substation - 750 kVA, 500 kVA

Packaged sub-station 11/0.433 KV, 50 Hz consisting of 11 kV, 3 way SF6 insulated compact RMU, oil cooled (Aluminium wound)/ dry type copper wound transformer and LT section with one ACB as incoming and 4 nos outgoing MCCB feeders and with encloser made of electromechanically galvanized

11 kV RMU - 2 X 630 A LBS + 1 X 200 A VCB (Motor Operated / SCADA ready ) 750 KVA Oil cooled (Al wound) / Dry Type (Cu wound) transformer LT Compartment : INCOMING:- 1 No. 1000 Amp, 415 Volt, 50 KA, FP, ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 400 Amp + 1x100 Amp + 1x63 Amp, TP MCCBs breaking capacity 35 KA with built in Thermo Magnetic Release

11 kV RMU - 2 X 630 A LBS + 1 X 200 A VCB (Motor Operated / SCADA ready ) 500 KVA Oil cooled (Al wound) / Dry Type (Cu wound) transformer LT Compartment : INCOMING:- 1 No. 800 Amp, 415 Volt, 50 KA, FP, ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 200 Amp + 1x100 Amp + 1x63 Amp, TP MCCBs breaking capacity 35 KA with built in Thermo Magnetic Release

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 25x6 mm. for earthing

Schedule C : Schedule of Quantities for Low Voltage OH Lines

8.5 mtr. steel latticed structure of 35x35x6 mm complete with nuts & bolts.

LT shackle insulator 3"x3 1/2".

D-clamp complete with G.I. pin, washers, nuts & bolts.

Guy assembly complete with 7/12 SWG GI stay wire, 110x75 mm LT guy insulator, 16mm dia stay rod,1.8 mtrs. long with bow thimble, turn buckle and 150x150x6mm anchor plate, GI stay clamp for lattice structure

AAC ANT conductor 50 sq.mm.

AAC GNAT conductor 25 sq.mm.

No. 12 SWG G.I wire for continuous earth wire

Al Binding Wire 10 SWG

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 304350 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

Danger Board 440 Volts.

Red Oxide paint @1.5 Ltr./pole.

Aluminium paint @1 Ltr./pole.

G.I Barbed wire @ 2Kg/pole.

Schedule D : Schedule of Quantities for Low Voltage UG cable lines

1.1 kV grade armoured cable (Al Conductor/XLPE Insulated/SWA/PVC Sheathed)

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

3.5 core x 35 sq.mm.

3.5 core x 25 sq.mm.

4 core x 16 sq.mm.

2 core x 16 sq.mm.

2 core x 10 sq.mm.

Rigid U PVC pipe as per IS 4985-2000 working pressure 6Kgf/cm2

160 mm dia.

110 mm dia.

75 mm dia.

50 mm dia.

1.1 KV indoor/outdoor end termination kit suitable for:

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

3.5 core x 35 sq.mm.

3.5 core x 25 sq.mm.

1.1 KV straight through jointing kit suitable for:

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

FEEDER PILLARS: OUTDOOR TYPE CUBICLE CONFORMING TO IS:8623-1 Main Feeder Panel: Cubicle design totally enclosed and water proof outdoor type floor mounted suitable for use in 440 V,400A as main feeder pillar Incomer : 1 No 400 A, MCCB, 50KA Outgoing: 2 Nos. 200 A TPN MCCB & 4 Nos. 32 A TPN, MCB for individual service connections.

FEEDER PILLARS: OUTDOOR TYPE CUBICLE CONFORMING TO IS:8623-1 Sub-Main Feeder Panel: Cubicle design totally enclo.& water proof outdoor type floor mounted suitable for use in 440V 200 A as a sub-main feeder pillar: Incomer: 1 No. 200 A, TPN MCCB Outgoing: 3 Nos. 63 A TPN MCCB & 4 Nos. 32 A MCCB for individual service connections & 8 Nos.16 A TPN for individual service

Safe earthing electrode Model T-19 short time current 20 KA rms for 1 sec (MV) application: 50 mm dia.x3 mtrs. electrode & 2 bags backfill Chemical compound .

GI strip 25mm X 5mm for earthing

Aluminium thimble of size;

Sundry itmes for 3.5C x 25 or 35 / 4C x 16 sqmm cable line installation for upto 30 Nos 3-phase connections for termination at switchgear / meterboxes ( like nails, saddle, etc.)

Sundry itmes for 4C x 16 / 2Cx 16 & 10 sqmm cable line installation for upto 50 Nos 1-phase & 3-phase connections for termination at switchgear / meterboxes ( like nails, saddle, etc.)

Schedule E : Schedule of Quantities for Low Voltage ABC lines

8.5 Mtr STP 410 SP21 complete with base plate, nuts & bolts

Tension / Dead End Clamp with hook attachment for AB Cable with insulated messenger, 50-70 sqmm, 20 kN breaking load

Tension / Dead End Clamp with hook attachment for AB Cable with insulated messenger, 25-35 sqmm, 20 kN breaking load

Suspension Clamp with hook attachment for AB Cable with insulated messenger, 25-95 sqmm, 16 kN breaking load

GI Pole Clamp for fixting hook attachment on STP pole

Piercing Connector TYPE -I, (Main 25-120 sqmm Tap Off 25-120 Sqmm)

Piercing Connector TYPE -II, (Main 35 -120 sqmm Tap Off 16-25 Sqmm) (provisional qty for st. lighting tapping)

1.1 kV XLPE Aerial Bunched Cable 3x120+1x70+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x95+1x70 +1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x70+1x50+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x50+1x35+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x35+1x35+1x16 sqmm, insulated neutral cum Messenger

Stay set including 16 mm Dia x 1.8 mtr Long Rod, and 110 x 75 x 6 mm Anchor Plate complete with 7/12 SWG Stay Wire, G.I Stay clamp

G.I. Back Clamps 75 x 8 mm flat complete with G.I Pole Clamp

Earthing Coil of 115 Turns of 50 MM Dia and 2.5 Mtr Lead of 4.0 mm G.I Wire

Push on type end caps for ABC, 16-120 sqmm

Three phase LT ABC Distribution Box with Spring Loaded Busbar System suitable for 1 Incoming 3 Outgoing 3 Phase Circuits

Single phase LT ABC Distribution Box Spring Loaded Busbar System suitable for 1 Incoming 6 Outgoing 1 Phase Circuit

4C x35 sqmm Al/PVC cable for connecting Dist. Box to ABC

2C x25 sqmm Al/PVC cable for connecting Dist. Box to ABC

Red Oxide Paint

Aluminium Paint

Anti Climbing Device (Barbed Wire)

440 Volt Caution Board

Description of Work / Item(s)

Amount

GPS survey and mapping

GPS survey and mapping of proposed LT overhead, LT ABC and LT Underground (main and sub-main feeders) lines

Description of Work / Item(s)

Amount

Schedule A1 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Non-Sealed Type) - 750 kVA, 500 kVA, 315 KVA, 250 KVA

INSTALLATION AND OTHER SERVICES

Erection, testing and commisioning of 750 / 500/ 315 / 250 KVA Distribution Transformer Station including H-pole with all equipment / accessories & painting, Distribution Transformer & LV Distribution Switchboard on parapet, cables and all connections earthing complete.

Civil Works (including material and works)

Concreting of 9 Mtrs. Lattice Structure / Swaged Steel Tubelar Pole in 1:4:8 cc in 0.9x0.9x1.75 mtrs Pit, Construction of parapet 0.61 x 0.61x0.153 mtrs. In 1:3:6 cc i/c 12mm cement plaster of parapet in 1:4 Mix.

Construction of parapet of size 1.5xl.5xlm trs. In 1:3:6 cc Mix including 12mm thick cement plaster in 1:4 Mix. for placement of 500/750 KVA Distribution Transformer

Construction of parapet of size 1.2x1.2x1mtrs. In 1:3:6 cc Mix including 12 mm thick cement plaster in 1:4 mix. for placement of 315 / 250 KVA Distribution Transformer

Construction of parapet of size 2x0.61x0.35x0.61 mtrs. In 1:3:6 cc mix including 12mm thick cement plaster in 1:4 mix. for Placement of L.T Distribution Board

Fencing for 400/500/630/750 KVA parapet mounted distribution sub-station of size 3.5x4 mtrs. constructed with 50x50x5mm M.S angle vertical props, 35x35x6mm M.S angle supports(double run), M.S wire mesh, 50x6mm M.S flat iron for clamping wire mesh complete with gate with locking arrangement, site development, concreting of props in 1:2:4 cc i/c soling & flooring works in 1:4:8 cc as per Layout No. 3/F/E&PD/400-750 KVA.

Fencing for 100/150/200/315 KVA parapet mounted distribution sub-station of size 3x3 mtrs.constructed with 50x50x5mm M.S angle vertical props, 35x35x6mm M.S angle supports(double run), M.S wire mesh, 50x6mm M.S flat iron for clamping wire mesh complete with gate with locking arrangement, site development, concreting of props in 1:2:4 cc i/c soling & flooring works in 1:4:8 cc as per Layout No.2/F/E&PD/100-315 KVA.

Schedule A2 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Hermetically Sealead) - 100 kVA, 63 kVA, 25 KVA

INSTALLATION AND OTHER SERVICES

Erection, testing and commisioning of 100 KVA Distribution Transformer Station including H-pole with all equipment / accessories & painting, Distribution Transformer and LV Distribution Switchboard on parapet, cables and all connections earthing complete.

Erection, testing and commisioning of 63 / 25 KVA Distribution Transformer Station including H-pole with all equipment / accessories & painting, Distribution Transformer on H-pole and LV Distribution Switchboard on parapet, cables and all connections & earthing, complete.

Civil Works (including material and works)

Concreting of 9 Mtrs. Lattice Structure / Swaged Steel Tubelar Pole in 1:4:8 cc in 0.9x0.9x1.75 mtrs Pit, Construction of parapet 0.61 x 0.61x0.153 mtrs. In 1:3:6 cc i/c 12mm cement plaster of parapet in 1:4 Mix.

Construction of parapet of size 1.2x1.2x1mtrs. In 1:3:6 cc Mix including 12 mm thick cement plaster in 1:4 mix. for placement of 100 KVA Distribution Transformer

Construction of parapet of size 2x0.61x0.35x0.61 mtrs. In 1:3:6 cc mix including 12mm thick cement plaster in 1:4 mix. for Placement of L.T Distribution Board

Fencing for 100/ KVA parapet mounted distribution sub-station of size 3x3 mtrs.constructed with 50x50x5mm M.S angle vertical props, 35x35x6mm M.S angle supports(double run), M.S wire mesh, 50x6mm M.S flat iron for clamping wire mesh complete with gate with locking arrangement, site development, concreting of props in 1:2:4 cc i/c soling & flooring works in 1:4:8 cc as per Layout No.2/F/E&PD/100-315 KVA.

Fencing for 10/16/25/63 KVA pole mounted distribution sub-station of size 2x3 mtrs.constructed with 50x50x5mm M.S angle vertical props, 35x35x6mm M.S angle supports(double run), M.S wire mesh, 50x6mm M.S flat iron for clamping wire mesh complete with gate with locking arrangement, site development, concreting of props in 1:2:4 cc i/c soling & flooring works in 1:4:8 cc as per layout No. 1/F/E&PD/10-63 KVA.

Schedule A3 : Schedule of Quantities for 11/0.433 kV Distribution Transformer (Dry Type / Outdoor) - 500 kVA, 250 kVA, 100 KVA

INSTALLATION AND OTHER SERVICES

Erection, testing and commisioning of 500/250/100 KVA Distribution Transformer Station including H-pole with all equipment / accessories & painting, Distribution Transformer and LV Distribution Switchboard on parapet, cables and all connections earthing, complete.

Civil Works (including material and works)

Concreting of 9 Mtrs. Lattice Structure / Swaged Steel Tubelar Pole in 1:4:8 cc in 0.9x0.9x1.75 mtrs Pit, Construction of parapet 0.61 x 0.61x0.153 mtrs. In 1:3:6 cc i/c 12mm cement plaster of parapet in 1:4 Mix.

Construction of parapet of size 1.5x1.5x1 mtrs. In 1:3:6 cc Mix including 12 mm thick cement plaster in 1:4 mix. for placement of 500 KVA Distribution Transformer

Construction of parapet of size 1.2x1.2x1 mtrs. In 1:3:6 cc Mix including 12 mm thick cement plaster in 1:4 mix. for placement of 250/100 KVA Distribution Transformer

Construction of parapet of size 2x0.61x0.35x0.61 mtrs. In 1:3:6 cc mix including 12mm thick cement plaster in 1:4 mix. for Placement of L.T Distribution Board

Fencing for 500 KVA parapet mounted distribution sub-station of size 3.5x4 mtrs.constructed with 50x50x5mm M.S angle vertical props, 35x35x6mm M.S angle supports(double run), M.S wire mesh, 50x6mm M.S flat iron for clamping wire mesh complete with gate with locking arrangement, site development, concreting of props in 1:2:4 cc i/c soling & flooring works in 1:4:8 cc as per Layout No.2/F/E&PD/400-750 KVA.

Fencing for 100-315 KVA pole mounted distribution sub-station of size 3x3 mtrs.constructed with 50x50x5mm M.S angle vertical props, 35x35x6mm M.S angle supports(double run), M.S wire mesh, 50x6mm M.S flat iron for clamping wire mesh complete with gate with locking arrangement, site development, concreting of props in 1:2:4 cc i/c soling & flooring works in 1:4:8 cc as per layout No. 1/F/E&PD/100-315 KVA.

Schedule B : Schedule of Quantities for 11/0.433 kV Packaged Substation - 750 kVA, 500 kVA

INSTALLATION AND OTHER SERVICES

Erection, testing and commisioning of Packaged Substation (750/500 kVA) including all equipment / accessories, cables and all connections earthing, complete.

Civil Works (including material and works)

Construction of parapet upto 1 m high of required dimensions for placement of 750 KVA PSS with provisions for HT & LT cable runs in 1:3:6 cc mix including 12mm thick cement plaster in 1:4 mix. and complying with OEM recommendations

Construction of parapet upto 1 m high of required dimensions for placement of 500 KVA PSS with provisions for HT & LT cable runs in 1:3:6 cc mix including 12mm thick cement plaster in 1:4 mix. and complying with OEM recommendations

Fencing for 400/500/630/750 KVA parapet mounted PSS of size 3.5x4 mtrs.constructed with 50x50x5mm M.S angle vertical props, 35x35x6mm M.S angle supports(double run), M.S wire mesh, 50x6mm M.S flat iron for clamping wire mesh complete with gate with locking arrangement, site development, concreting of props in 1:2:4 cc i/c soling & flooring works in 1:4:8 cc as per Layout No. 3/F/E&PD/400-750 KVA.

Schedule C : Schedule of Quantities for Low Voltage OH Lines

INSTALLATION AND OTHER SERVICES

Dismantling of existing bare conductor 3P5W LT OH lines including removal of poles / lattice structures, insulators, D-clamps, conductors, stays and all accessories, filling and restoration of pits / surfaces, clearance of RoW and returning all salvaged materials to PDS regional stores (provisional qty subject to field requirement)

Dismantling of existing bare conductor 2P2W LT OH lines (as per field requirement) including removal of poles / lattice structures, insulators, D-clamps, conductors, stays and all accessories, filling and restoration of pits / surfaces, clearance of RoW and returning all salvaged materials to PDS regional stores (provisional qty subject to field requirement)

Erection of 8.5 mtr. steel lattice structure, fitting and fixing of all materials (fully dressed) including LT shackle insulatosr, D-clamps & other accesories, existing street lamps, danger plate & barbed wire etc and painting ( but excluding concreting to be priced seperately)

Erection of complete LT Guy assembly with GI stay wire (excluding concreting to be priced seperately)

Stringing of 3 x phase + neutral conductors and earth wire at proper tension/ sag, including insulator binding, earthing (as per applicable std), connecting line with DTR switchboard, reconnecting all exsisting consumer services and street lamps, testing and commisioning of line, complete

Stringing of 1 x phase + neutral conductors at proper tension/ sag, including insulator binding, earthing (as per applicable std), connecting line with DTR switchboard, reconnecting all exsisting consumer services & street lamps, testing and commisioning of line complete

Civil Works (including material and works)

Concreting of 8.5 mtr. Structure in 1:4:8 cc in 0.9x0.9x1.50 mtrs. pit, contruction of parapet 0.35x0.475xx0.153 mtrs. in 1:3:6cc i/c 12mm cement plaster of parapet in 1:4 mix.

Concreting of LT guy assembly in 1:4:8cc in 0.30x0.30x1.05 mts. pit.

Schedule D : Schedule of Quantities for Low Voltage UG cable lines

INSTALLATION AND OTHER SERVICES

Dismataling of existing bare conductor 3P5W LT OH lines including removal of poles / lattice structures, insulators, D-clamps, conductors, stays and all accessories, filling and restoration surfaces of pits and returning all salvaged materials to PDS regional stores (provisional qty as per field requirement)

Erection of Main LV Feeder Lines : Laying of cables of size 3.5 C x 150 / 185/ 240 or 300 sqmm in UPVC pipes including cable joints, connecting cable line with existing DTR / PSS, testing and commisioning (excluding trench works to be quoted seperately under civil works)

Erection of Sub-Main LV Feeder Lines : Laying of cables of size 3.5 C x 50/ 95 or 120 sqmm in UPVC pipes including cable joints , testing and commisioning (excluding trench works to be quoted seperately under civil works)

Erection of LV line connections : Laying of cables of size 3.5C x 25 / 35 sqmm and 4Cx 16 sqmm and in UPVC pipes ( multiple circuits) including all connections & terminations for upto 20 Nos 3-phase connections , testing and commisioning (excluding trench works to be quoted seperately under civil works)

Erection of LV line connections : Laying of cables of size 4Cx 16 sqmm and 2C x 16 / 10 sqmm in UPVC pipes ( multiple circuits) including all connections & terminations for upto 50 Nos 1-phase & 3-phase connections , testing and commisioning (excluding trench works to be quoted seperately under civil works)

Installation, testing and commisioing of 400 A Main Feeder Pillar Panel inclding all cable connections, terminations and earthing ( excluding mounting parapet to be quoted seperately under civil works)

Installation, testing and commisioing of 200 A Sub-Main Feeder Pillar Panel / L.T distribution switch board inclding all cable connections, terminations and earthing ( excluding mounting parapet to be quoted seperately under civil works)

Civil Works (including material and works)

Excavation of 0.45x0.90x1.00 m cable trench in mix soil & refilling with available excavated earth and providing concreting / tiles on the top of the trench.

Construction of parapet of size 2x0.61x0.35x0.61 mtrs. In 1:3:6 cc mix i/c 12mm thick cement plaster in 1:4 mix. for lacement of L.T. Feeder Pillar / Distribution Board

Schedule E : Schedule of Quantities for Low Voltage ABC lines

INSTALLATION AND OTHER SERVICES

Dismataling of existing bare conductor 3P5W LT OH lines (as per field requiremen t) including removal of poles / lattice structures, insulators, D-clamps, conductors, stays and all accessories, filling and restoration surfaces of pits and returning all salvaged materials to PDS regional stores (provisional qty)

Erection of 8.5 mtr. STP pole including fixing of all materials (fully dressed) including , tension / suspension clamps, ABC distribution boxes. other accesories, existing street lamps, danger plate & barbed wire etc and painting ( excluding concreting to be priced seperately under civil works)

Erection of complete LT Guy assembly with GI stay wire (excluding concreting to be priced seperately uunder civil works)

Stringing of AB cable at proper tension / sag and providing connections to existing DTR switchboard, ABC distribution boxes, line earthing, end caps, reconnecting all existing consumer services and street lighting, testing and commissioning of AB line, complete. (All connections shall be made via Insulated Piercing Connectors and any damages or exposed parts of AB cable strictly not permitted)

Civil Works (including material and works)

Concreting of 8.5 STP M15 Grade, 0.25 cum per pole including muffling above GL 300 mm

Concreting of Guy Assy Set, M15 Grade, 0.2 cum per stay

Description of Work / Item(s)

Amount

Total Price CIP in EUR (Schedule 1)

Total Price CIP in USD (Schedule 1)

Total Price CIP in JPY (Schedule 1)

Total Price of Taxes & Duties in INR (Schedule 1)

Total Price EXW in INR (Schedule-2)

Total Price of Design Services in INR ( Schedule-3)

Total Price of Incidental Expenses in INR( Schedule-4A)

European Euro

Japanese yen

US Dollar

European Euro

Japanese yen

US Dollar

European Euro

Japanese yen

US Dollar

European Euro

Japanese yen

US Dollar

Description of Work / Item(s)

INCOMING:- 1 No. 1000 Amp, 415 Volt, 50 KA, FP, Draw Out type ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 400 Amp TP MCCB breaking capacity 35 KA, 1 No. 100 Amp TP MCCB breaking capacity 35 KA & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA all with built in Thermo Magnetic Release

INCOMING:- No. 800 Amp, 415 Volt, FP, manually Draw Out type ACB with in built Thermo Magnetic Release & 6No+6Nc Auxiliary contacts. Outgoing:- 3 Nos. 200 Amp TP MCCB breaking capacity 35 KA , 1 No. 100 Amp TP MCCB breaking capacity 35 KA & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA, all with built in Thermo Magnetic Release

INCOMING: 1 No. 630 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 200A TP MCCB, 50 KA & 1 No. 63A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 400 A, 4P,50KA, MCCB OUTGOING: 1 No. 200A TP MCCB, 50 KA ,2 Nos. 100A TP MCCB, 35 KA & 1 No. 63A TP MCCB, 35 KA, all with built in Thermo Magnetic Release.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

11 kV, 3 X 35 sq.mm Cu / XPLE Cable

Heat Shrinkable Outdoor type end termination kit for 11 KV (E) 3 core XLPE (Kit No.EOKT 3091-3131) Raychem make or equivalent : 3 C X 35 sqmm

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

Back clamps of 50x8mm G.I. flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III) Raychem RPG make or equivalent

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 25x6 mm. for earthing

1.1 kV 1Cx240 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer) (2 cables /cct for 750 / 500 KVA, 1 cable/cct for 315/250 KVA)

Tinned Copper Lugs - 240 sqmm

AAAC Rabbit Conductor (for down wires)

Al Line Tap / PG Clamp, Double Bolt, 25-150 sqmm

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Spare Fuse element tubes for DOF of 750 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 500 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 315 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 250 KVA Distribution Transformer

INCOMING: 1 No. 200 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 100A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 100 A, 4P,50KA, MCCB OUTGOING: 3 Nos. 63A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

INCOMING: 1 No. 63 A, 4P,50KA, MCCB OUTGOING: 2 Nos. 40A TP MCCB, 35 KA, & 1 No. 32A TP MCCB, 35 KA all with built in Thermo Magnetic Release.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole 200 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

11 KV, 3 Pole, 200 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

G.I. channel 75 X 40x4.8mm X 1.2 m long for mounting of DT

Back clamps of 50x8mm G.I. flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III)

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

GI strip 25x6 mm. for earthing

1.1 kV 1Cx50 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer)

Tinned Copper Lugs - 50 sqmm

AAAC Rabbit Conductor (or down wires)

Al Line Tap / PG Clamp, Double Bolt, 25-150 sqmm

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Spare Fuse element tubes for DOF of 100 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 63 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 25 KVA Distribution Transformer

INCOMING:- 1 No. 800 Amp, 415 Volt, FP, manually Draw Out type ACB with in built Thermo Magnetic Release & 6No+6Nc Auxiliary contacts. OUTGOING:- 3 Nos. 200 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release & 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release

INCOMING : 1 Nos. 400 Amp,415V, FP MCCB breaking capacity 50 KA with built in Thermo Magnetic Release, OUTGOING : 1 Nos. 200 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 3 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release.

INCOMING:- 1 Nos. 200 Amp,415V, FP MCCB breaking capacity 50 KA with built in Thermo Magnetic Release. OUTGOING:- 2 No. 100 Amp TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release, 1 No. 63 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release & 1 No. 32 Amp. TP MCCB breaking capacity 35 KA with built in Thermo Magnetic Release having Relay setting 16-25A.

11 KV, 3 Pole 400 amp, Air Break Gang Operated Switch (G.O.S) tilting type, three insulator per phase, complete with all fittings confirming to IS: 9920 & IS: 9921 Raychem RPG make or equivalent

11 KV, 3 Pole, 400 amp. Drop-out Fuse (D.O.F Unit) complete with all accessories including fuse element rated for transformer capacity confirming to IS: 9385 Raychem RPG make or equivalent

3 X 35 sq.mm 11 KV Cu / XPLE Cable

Heat Shrinkable Outdoor type end termination kit for 11 KV (E) 3 core XLPE (Kit No.EOKT 3091-3131) Raychem make or equivalent : 3 C X 35 sqmm

9 Mtrs. Steel lattice structure of 35x35x6mm M.S Angle complete with nuts & bolts conforming to specification of design detail No. 2/L/FT/E&PD/ 9 Mtrs.

G.I. channel 75X40X4.8mmX2.2 m long for DP.

Back clamps of 50x8mm G.I.flat for holding channel.

G.I. nuts & bolts of 16mm dia.X 40mm length.

9 KV, 10 KA Single pole unit Metal Oxide Gapless Surge Arrestor with earth lead disconnector, bird protection cap and mounting brackets. for 11 KV, 50 c/s solidly earthed neutral system confirming to IS:3070 (Part III)

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 35x6 mm. for earthing

1.1 kV 1Cx150 sqmm, Cu/XLPE/PVC (DTR to LT D-Board Incomer) (2 cables / cct for 500 kVA)

Tinned Copper Lugs - 50 sqmm

AAAC Rabbit Conductor

Red oxide paint @ 1.5 ltr/ pole

Aluminium paint @ 1.0 ltr / pole

11 kV Caution Board

Spare Fuse element tubes for DOF of 500 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 250 KVA Distribution Transformer

Spare Fuse element tubes for DOF of 100 KVA Distribution Transformer

11 kV RMU - 2 X 630 A LBS + 1 X 200 A VCB (Motor Operated / SCADA ready ) 750 KVA Oil cooled (Al wound) / Dry Type (Cu wound) transformer LT Compartment : INCOMING:- 1 No. 1000 Amp, 415 Volt, 50 KA, FP, ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 400 Amp + 1x100 Amp + 1x63 Amp, TP MCCBs breaking capacity 35 KA with built in Thermo Magnetic Release

11 kV RMU - 2 X 630 A LBS + 1 X 200 A VCB (Motor Operated / SCADA ready ) 500 KVA Oil cooled (Al wound) / Dry Type (Cu wound) transformer LT Compartment : INCOMING:- 1 No. 800 Amp, 415 Volt, 50 KA, FP, ACB with microprocessor Release (IPR E 4 Pole) Outgoing:- - 2 Nos. 200 Amp + 1x100 Amp + 1x63 Amp, TP MCCBs breaking capacity 35 KA with built in Thermo Magnetic Release

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 3043: 50 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

G.I. strip 25x6 mm. for earthing

8.5 mtr. steel latticed structure of 35x35x6 mm complete with nuts & bolts.

LT shackle insulator 3"x3 1/2".

D-clamp complete with G.I. pin, washers, nuts & bolts.

Guy assembly complete with 7/12 SWG GI stay wire, 110x75 mm LT guy insulator, 16mm dia stay rod,1.8 mtrs. long with bow thimble, turn buckle and 150x150x6mm anchor plate, GI stay clamp for lattice structure

AAC ANT conductor 50 sq.mm.

AAC GNAT conductor 25 sq.mm.

No. 12 SWG G.I wire for continuous earth wire

Al Binding Wire 10 SWG

SAFE EARTHING MODEL T-19 SHORT CURRENT 20KA RMS FOR 1 SEC(LV / MV) APPLICATION CONFORMING TO IS: 304350 mm diameter x 2 mtrs. Electrode (Copper bonded) & One bag backfill chemical compound.

Danger Board 440 Volts.

Red Oxide paint @1.5 Ltr./pole.

Aluminium paint @1 Ltr./pole.

G.I Barbed wire @ 2Kg/pole.

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

3.5 core x 35 sq.mm.

3.5 core x 25 sq.mm.

4 core x 16 sq.mm.

2 core x 16 sq.mm.

2 core x 10 sq.mm.

160 mm dia.

110 mm dia.

75 mm dia.

50 mm dia.

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

3.5 core x 35 sq.mm.

3.5 core x 25 sq.mm.

3.5 core x 300 sq.mm.

3.5 core x 240 sq.mm.

3.5 core x 185 sq.mm.

3.5 core x 120 sq.mm.

3.5 core x 95 sq.mm.

3.5 core x 50 sq.mm.

FEEDER PILLARS: OUTDOOR TYPE CUBICLE CONFORMING TO IS:8623-1 Main Feeder Panel: Cubicle design totally enclosed and water proof outdoor type floor mounted suitable for use in 440 V,400A as main feeder pillar Incomer : 1 No 400 A, MCCB, 50KA Outgoing: 2 Nos. 200 A TPN MCCB & 4 Nos. 32 A TPN, MCB for individual service connections.

FEEDER PILLARS: OUTDOOR TYPE CUBICLE CONFORMING TO IS:8623-1 Sub-Main Feeder Panel: Cubicle design totally enclo.& water proof outdoor type floor mounted suitable for use in 440V 200 A as a sub-main feeder pillar: Incomer: 1 No. 200 A, TPN MCCB Outgoing: 3 Nos. 63 A TPN MCCB & 4 Nos. 32 A MCCB for individual service connections & 8 Nos.16 A TPN for individual service

Safe earthing electrode Model T-19 short time current 20 KA rms for 1 sec (MV) application: 50 mm dia.x3 mtrs. electrode & 2 bags backfill Chemical compound .

GI strip 25mm X 5mm for earthing

Sundry itmes for 4C x 16 / 2Cx 16 & 10 sqmm cable line installation for upto 50 Nos 1-phase & 3-phase connections for termination at switchgear / meterboxes ( like nails, saddle, etc.)

8.5 Mtr STP 410 SP21 complete with base plate, nuts & bolts

Tension / Dead End Clamp with hook attachment for AB Cable with insulated messenger, 50-70 sqmm, 20 kN breaking load

Tension / Dead End Clamp with hook attachment for AB Cable with insulated messenger, 25-35 sqmm, 20 kN breaking load

Suspension Clamp with hook attachment for AB Cable with insulated messenger, 25-95 sqmm, 16 kN breaking load

GI Pole Clamp for fixting hook attachment on STP pole

Piercing Connector TYPE -I, (Main 25-120 sqmm Tap Off 25-120 Sqmm)

Piercing Connector TYPE -II, (Main 35 -120 sqmm Tap Off 16-25 Sqmm) (provisional qty for st. lighting tapping)

1.1 kV XLPE Aerial Bunched Cable 3x120+1x70+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x95+1x70 +1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x70+1x50+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x50+1x35+1x16 sqmm, insulated neutral cum Messenger

1.1 kV XLPE Aerial Bunched Cable 3x35+1x35+1x16 sqmm, insulated neutral cum Messenger

Stay set including 16 mm Dia x 1.8 mtr Long Rod, and 110 x 75 x 6 mm Anchor Plate complete with 7/12 SWG Stay Wire, G.I Stay clamp

G.I. Back Clamps 75 x 8 mm flat complete with G.I Pole Clamp

Earthing Coil of 115 Turns of 50 MM Dia and 2.5 Mtr Lead of 4.0 mm G.I Wire

Push on type end caps for ABC, 16-120 sqmm

Three phase LT ABC Distribution Box with Spring Loaded Busbar System suitable for 1 Incoming 3 Outgoing 3 Phase Circuits

Single phase LT ABC Distribution Box Spring Loaded Busbar System suitable for 1 Incoming 6 Outgoing 1 Phase Circuit

4C x35 sqmm Al/PVC cable for connecting Dist. Box to ABC

2C x25 sqmm Al/PVC cable for connecting Dist. Box to ABC

Red Oxide Paint

Aluminium Paint

Anti Climbing Device (Barbed Wire)

440 Volt Caution Board