Illumination facility from National Highway to Club Building at Jammu Tawi Golf Course, Sidhra

Amount

Supply, installtion of Hot dip Galvanised 16m High Mast for LED flood lights with motorised carriage of approved makes with its accessoreis, Mast shall be in two section hot dip galvanised and suitable for wind velocity as per IS:875 (i.e. 55 m/sec). It should also include accessories of the high mast including head frame, steel wire rope 6mm (dia 7/19 construction), Trailing cable, double drum winch, galvanised luminaire Carriage sutiable for required luminaries symmetrically as shown in the lighting design and its control gear boxes, lighting final. The mast shall have integral power tool installaled in the base compartment for its operation including one set (6 No.) of foundation bolts manufactured from special steel along with nuts,washers, anchor plates and templates. Make:SYSKA/Bajaj/Surya.Complete as per the instructions of Engineer Incharge.

Providing reinforced cement concrete foundation of size and design as per drawing approved by OEM original Equipment manufacturer which should be strickly followed.

Supply,installtion,testing and commissioning of 250W LED flood lights with min 120 lumens/watt with LM 79 and LM 80report with min IP 65 protection. Make:Syska/Panasonic/Philips/Bajaj/IB Complete as per the instructions of Engineer Incharge.

Sypply,installtion, testing and commissioning of floor Mounted Outdoor Type Double Door Low voltage outdoor panel IP54 Suitable for operation on 433V 4 Phase, 50Hz Supply, Made for 2.0mm CRCA Sheet enclosure with luminium bus bar four wire with following switchgears and metering. Necessary arrangement be made for termination of incoming cable and outgoiing cables. LT Panel shall be manufactured as per IS8623. Complete as per the instructions of Engineer Incharge.

Incomer

63 A 4 Pole MCCB 25-KA-1 No.

60A 4 Pole contractor-1 No.

Digital Astronomical based time switch equivalent to 1 Channel Alpharex Astro-1 No. Make : L&T, Legrand, Siemens

Surge protection Device Class B+C 3P+N Legrand/OBO/JMV

Bushar shall be Almunium TPN 200A duly supported on DMC insulators and covered with heat shrinkable color coded PVC sleeves

Outgoings

32A 2 Pole MCB 10 KA-10 Nos

32 A 4 Pole MCB 10-KA-1 No

Make of MCCB/Contractor/TimeSwitch/SPD: Schneider (Acti-9), Legrand (DPX3), Siemens (Betagard)/L&T/C&S

One No industrial socket of min 20 A cap.

Supply and laying of 3 core 2.5 sqmm cable form panel to LED Lights including connection at both ends.

Supply and laying of main cable from existing transformers station pannel up to proposed site of panel for high mast lighting with 4 X 35 Sq mm Aluminium Armoured cable (Make Polycab/KEI/Gloster) laid in HDPE Pipe (ISI mark PN 8) of 4" by digging trench of 0.75 mtx x 1mt through the main panel with MCCB 4P, 63A. Complete as per the instructions of Engineer Incharge.

Chemical type Maintainance free earthing with 3 MTR 50 MM GI electrode with connection of panel/high mast with 25 x 3 mm GI Strip make JMVGMAX/OBO with CPRI approved and NABL certified test report. Complete as per the instructions of Engineer Incharge.

Construction of platform of Size 10' X 8'X4' including brickwork and P.C.C of M-10 P.C.C Grade (1:3:6) 1 Cement, 3 Sand, 6 crushed course stone agg. Including earthwork as directed by the engineer-in-charge and laying of 40 mm thick cement concrete flooring 1:2:4 finished with a floating coat of neat cement slurry on top and plastering the exposed sides with cement mortar 1:4 complete in all respects alongwith steps.

Supply and laying of 240 sq.mm 3.5 core aluminium armoured cable with thimbling and tapping as required at site and laying it in PVC Pipe (Astro/Supreme/Prince/Filonex with pressure capacity 110cm.sq) of 160 mm by digging trench of 1 mtr deep and 0.75 mtr wide and covering it back as it was earlier. Make : Polycab/KEI/Gloster

Supply, Testing, Fixing and commission of 350 watt LED Flood light with average lux not less than 110 lumens/watt. The light must be outdoor type vibration, surge and weather proof with high energy efficient capable of illumination open field for playing at night with IP 66 level of protection. Make philips, cromption, IBled, Havells, Syska

Supply, Testing, Fixing and comissiong of 240 X 3.5 Core outdoor type termination kit MAKE 3m, Raychem, Yamuna Densons.

LT Panel

Panel 1:

Incomer : 200 A 4 Pole MCCB 50 KA

Outgoing :

1) 6A/16/32A SP 10 KA C Curve MCB : 4 No

2) 32 A 4 Pole 18 KA MCCB : 1 No

3) Motor Starter of 1 HP DOL

4) Motor Starter of 10 HP FASD Type

SPD with B+C protection (make : JMW/OBO/Teracel)

The panel should have provision for incomer cable of 3.5 c 35mm sq for the outgoing cable as per the outgoing No. of MCB AND MCB

One No industrial socket of min 20 A cap.

Panel should be made of CRCA 1.6 mm thick sheet and duly painted with two coats of powder coating, outdoor type, with stand made of 50 mm x 6 mm thick angle to be grouted at height of 2 feet from ground level. The panel should be outdoor type with double door arrangement, dust and vermin proof with ammeter and voltmeter for each phase (CPRI APPROVED)

Make: Power control system/Jaima/Gupta and Friends. JK Power Control. Make for switch Gear/MOTOR STARTER : BCH/ABB/ L&T

GLOBAL ENGINEERS