PROVN OF VEH CAR PARKING, GUARD ROOM, TOILETS ETC AND OTHER SANCTION WORK AT HISAR MIL STN UNDER GE HISAR

Amount

Excavating in trenches not exc 1.5 metre wide and not exc 1.5 metre in depth for foundation or for shafts, walls, manholes, laying of cables, pipes etc not exc 10 Sqm on plan and getting out in soft/loose soil.

Removing excavated surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point etc complete all as specified and directe.

Returning filling in incl spreading leveling watering and well ramming in layers n. exc 25cm thick etc complete all as specified and as directed by Engineer-in-Charge.

M&L PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete.

M&L for 100mm thick PCC (1:4:8) type D2 using 40 mm graded crushed stone aggregate as in sub base, surface finished fair and even complete all as specified.

M&L for 75mm thick PCC 1:3:6 type C1 using 20 mm graded crushed stone aggregate as in plinth protection surface finished fair and even complete all as specified. Note :- Plinth protection shall be of width as directed and shall be laid to slope of 1:30 in alternative bays not exceeding 3 meter in length. Joints of 6 mm wide and 10 mm deep shall be provided along the wall and bays and same shall be filled with bitumen mastic (1:3).

M&L reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, shelves and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in foundations including rafts, footings, foundation beams, bases for columns, mass concrete and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for reinforced cement concrete M-25 (Design mix) using 20mm graded crushed stone aggregate in columns, pillars, piers, posts, struts and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L reinforced cement concrete M-25 grade (Design mix) using 20mm graded stone aggregate in chajjas and the like. Note :- Reinforcement & formwork shall be measured and paid for separately.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter for rough finished flat surfaces of concrete.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions, square, rectangular or polygonal for rough finished flat surfaces of concrete.

M&L formwork to sides and soffits of floor or roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished flat surfaces of concrete.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work, not exc 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete all as specified and directed.

M&L formwork to flat surfaces of chajjas, chullah hoods, troughs and similar items including edges for rough finished surfaces.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 5cm but n exc 10cm wide for rough finished flat surfaces of concrete all as specified and directed.

M&L for reinforcement TMT bars 10 mm dia and over cut to length, bent to shape required, including cranking, bending spirally or hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified.

All as per serial item No. 18.00 here-in-before but 5mm dia including 10mm dia in stirrups.

M&L for brick work using old size sub class B bricks as specified straight or curved on plan exc 6.00 metre mean radius, built in cement mortar 1:6 complete all as specified.

M&L brick work with subclass 'B' old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified.

M & L for rendering 10mm thick in cement mortar 1:6 on faces of brick work or concrete surfaces of walls, finished even and smooth without using extra cement complete all as specified.

M&L for 15 mm rendering with CM (1:4) with using water proffing compound on fair face of wall or on concrete surfaces finished even and smooth without using extra cement complete all as specified

M&L rendering 5mm thick in cement mortar 1:3 on concrete surfaces in ceiling, finished even & smooth without using extra cement including taking cement plaster complete all as specified.

Supply only water proofing compound (ISI marked).

Material and labour preparation of newly plastered/asbestos cement surfaces of ceilings & applying three coats of white wash complete all as specified.

Material and labour preparation of newly plastered/asbestos cement surfaces of wall & applying three coats of white wash complete all as specified.

Material & Labour for perparation of new surfaces and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and as directed by Engineer-in-Charge.

M&L screed bed or bedding layer of cement mortar 1:4, 15mm thick for laying floor finishes.

M&L for PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in levelling course of floors and roofs 25mm thick finished fair & even complete all as specified & as directed.

M&L for non skid ceramic jointfree tiles (coloured) premium quality, 7 to 8mm thick, area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match

M&L for glazed coloured ceramic tiles premium quality, 300mm x 450mm x 7mm thick including 10mm thick rendering 1:4 (black coat) on vertical surface such as skirting/dado etc set and jointed neat cement slurry & pointed in colour cement.

S&F anodized aluminium frame for doors, windows, ventilators, partitions, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) with one or more rebates including joining cleat for fixing etc. complete all as specified & as directed.

Supply and fixing 4mm thick figured glass, pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane including painting / oiling to new putty to match with the existing/new surfaces, including hacking out old broken glass any thickness, size, quality or description from metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed.

Supply and fixing in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified.specified.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms, counter for washbasin and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

S&F vitreous china (flat back) counter type wash basin of size 550 x 400 mm over granite slab of size 1.2m x 0.6m x 18mm thick, PVC Connection, waste coupling etc all as specified and directed by Engineer-in-Charge

S&F vitreous china squatting pan (Orissa pattern) of size 580x440mm white with integral foot rests, with CI 'P' or 'S' trap, and fixing in lime concrete (1 lime, 2 sand and 5Aggreate 150mm thick all around and finished just below level rim of pan to receive the floor finish complete all as specified

S&F PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F 15 mm bore CP brass bib tap fancy type with crutch or butterfly handles screwed down Ea screwed for iron pipe complete all as specified

S&F stainless steel soap dish fixed to wall as directed.

S&F angle valves chrome plated fancy type 15 mm bore, cast copper alloy screwed down Ea high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions all as specified and directed by Engr-in-charge.

S&F 15mm bore stop valve,/ gate valve cast copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions.

S&F Vitreous China urinals, bowl type (back or corner wall type), complete including providing and Ea fixing plugs, bedding urinal against wall in cement mortar 1.2, securing urinal to plugs with and mm long brass screws, pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe.

S&F 15mm bore fancy type pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly nuts, screwed for iron pipes & fly nuts, screwed for iron pipes all as specified and directed.

S&F waste pipe PVC low density polyethylene 32 mm dia all as specified and directed.

S&F Grating doom 100 mm dia with waste hole of PTMT (Minimum weight 25 gms) all as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls with necessary MS / PVC clamps and necessary screwing complete all as specified.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints fixed to walls with necessary clamps/ laid in floor complete all as specified.

Supply and fixing 110 mm bore PVC (SWR) bends any radius with access door complete all as specified.

S&F 110mm PVC (SWR) junction double, (double T) equal or unequal provided with access door complete all as specified and directed.

S&F PVC (SWR) Gully trap 125/110mm, setting and jointing with solvent cement complete all as specified.

S&F PVC floor trap of 75 mm bore, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified & as directed.

Supply and fixing 1000 Litre capacity Rotational moulded polyethylene water storage tanks (colour other than black as approved by Engineer-in-charge) triple layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete as specified in SSR Part-I.

S&F Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20mm bore (minimum weight 210 gms) complete all as specified and as directed.

Supply and fixing factory made single extruded WPC (wood polymer composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk /wheat husk )and toxic additives (maximum toxicity index of 12 for 100gms) having miniumum density of 650 kg/cum and screw withdrawal strength of 1800N (face) & 900N (Edge), miniumum compressive strength 50N/mm2, modulus of elasticity 850 N/mm2 and resisitance to spread of flame of class A category with property of being termite / borer proof, water/moisture proof and fire retardant WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces threaded star headed counter sunk S S screws all as per direction of Engr-in-Charge

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 65 x 100 mm (SIngle rebated) comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

Supply & fixing butt hinges of size 125mm heavy weight, cold rolled mild steel ISI marked complete all as specified.

S&F 150mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised (ISI marked) complete all as specified.

S&F 300mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 150mm complete all as specified.

S&F anodized aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m, powder coated of any colour as approved (Thickness or powder coating not less than 50 micron) including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as peg stays 150mm long (1 No.), hinges type B-21 100mm long (2 Nos), suitable handle (1 No.) complete all as specified & as directed.

Supply and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminte shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame complete as specified by the manufacturer and all as directed.

Supply and fixing 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames, complete as specified by the manufacturer and all as directed.

Supply & fixing butt hinges of size 100mm medium weight, cold rolled mild steel ISI marked complete all as specified.

S&F 200 mm long aluminium anodized barrel tower bolts of extruded section (ISI marked) complete all as specified.

S&F 200mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified.

Supply & fixing aluminium handle 150mm size cast type, anodized complete all as specified.

S&F tubular towel rail, brass chromium plated, 20mm dia, ‘D’ type, 60cm long between flanges.

S & F brass chromium plated shower rose 125mm size with swivel joint suitable for fixing with 15 mm bore pipe including shower arm 15mm bore size with bend of 45 degree with flange

M&L for 15 mm thick screed bed or bedding layers in CM 1:6 over roof surfaces without using extra cement for screed bed with water proofing compound (WPC) as directed by Engr-in-Charge

M&L for providing 10mm thick polymer modified plaster in ration 1:10 (1 Part of polymer and 10 parts of cement with solid contents not less than 30%) over slab and applying priming coat of epoxy primer with resin and hardner with water dilution as per manufacturer instructions, applying 1st coat of solvent based polyurathene liquid membrane not less than 500 micron thick UV stable having SRI value greater than equal to 105 with consumption of 0.61 Kg/Sqm and applying 2nd coat solvent based polyurathene liquid mambrane not less than 500 micron thick UV stable having SRI value greater than liquid to 105 with consumption of 0.61 Kg/Sqm over dried 1st coat complete all as specified and directed.

S&F RCC hume pipe NP2 grade drain pipes of 150mm bore, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, cooler stand and similar work including welding conforming to Grade E-165 (Fe 290), complete, all as specified & directed.

S&F vitreous china wash down water closet (Padestal pattern) White, with 'P' or 'S' trap including plastic water closet seat cover, black, closed pattern with flat bottom with mild steel chromium plated or aluminium hinging device and fixing with all joints including connection to drain or outgoing pipe and to flushing pipe, anti-syphonage pipe etc complete all as specified and as directed.

M&L for 20mm thick screed bed or bedding layers in CM 1:6 over roof surface without using extra cement for screed bed with water proofing compound (WPC) as directed by Engr-in-Charge

Excavating in post holes (or similar holes) each n exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50 m and making good surface.

S&F mild steel work such as angle iron in posts & struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc., flat iron fillets (for securing wire mesh etc) including 10mm dia MS round bars as in tie bars fixed to fencing posts including necessary welding where required as per site requirement and other similar works complete, conforming to Gde E-165 (Fe 290).

M & L Structural steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc

S & F Plates (plain or chequered) channels, square cut or notched (ordinary & counter sunk) forming holes, with riveted, bolted or welded attachment

Preparation of newly steel surface and applying two coat of synthetic enamel paint over a coat of red oxide complete all as specified & as directed.

S&F for pre painted galvalume aluminium zinc coating Gl based corrugated steel sheet 0.50 mm thick an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall/ Eaves, fixed with self-tapping screws all as specified & as directed.

Surface excavation not exc 30cm deep and averaging 15cm deep and getting out in soft/loose soil and getting out

M&L for hardcore of broken stone or boulders, gauge not exc. 63mm, deposited, spread and leveled in layers not exc 15 cm thick, watered and rammed to a true surface all as directed.

M&L for factory made 60mm thick machine pressed precast cement concrete coloured interlocking paver blocks glossy finish of Grade M-35 conforming to IS 15658-2006 of shape and size as directed with grey cement and pigment laid over & including 25mm thick sand cushioning, joints of blocks filled with dry sand and compacted with mechanical vibrator complete all as specified & directed.

M&L for Sand cushioning 230mm thickness with dry sand (one layer of 80mm thickness before laying of cable and other layer of 150mm thickness after laying of cable) and punned down to 180mm after laying of cable in trenches for protection of cable complete all as directed. Note :- For the purpose of payment only punned thickness shall be measured.

S&F factory made (SFRC) precasted reinforced cement concrete round manhole cover as required thickness not less than 50mm of size 1200mm x 600mm, edge of manhole cover to be locked with 1mm thick MS sheet complete all as specified and directed.

Material and labour PCC 1:4:8 type D-2 using 40 mm graded stone aggregate in bedding to SGSW drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed.

M&L for preparation of new wall surfaces and applying two coats of Oil Bound Distemper over a coat of primer.

M & L Preparing new plastered surfaces and applying two coats of cement base paint on walls.

M&L for vitrified ceramic tiles (light Shade) 10mm thick (square/rectangular), polished, area of each tiles not exc 0.36 sqm in floors etc set and jointed in neat cement slurry ad pointed in white or coloured cement to the match, encluding 10mm thick screed bed in cement mortar 1:4 over, complete all as specified and as directed.

S&F GI powder coated snap grid of sizes 605 mm x 605 mm frame work for false ceiling with main tee 32 x 24 x 1mm thick, cross Tee 26 x 24 x 1mm and wall angle 24 x 24 x 1mm thick, flange covered with PVC thin includng hangers 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long including Gypsum board 7-9mm thick duly finished surface (thin PVC layer on gypsum board as per maunfacturer's instructions) of size 700mmx700mm thick and the same shall be placed in snap grid as in false ceiling complete all as specified & directed.

S&F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified & as directed.

S&F Door closer aluminium (extruded section body), hydraulically regulated, designation No. 2 universal type, suitable for door shutters of 851mm to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & as directed.

M&L for point wiring for one light point controlled by one, one way switch with 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade including 1.50 Sqmm single core PVC insulated and unsheathed multistranded copper conductor FRLS cable 1100 Volt grade as continuous earth wire in green colour to common earth and connected to earth dolly laid/drawn into and including concealed PVC rigid non metallic conduit 20/25mm dia medium grade (ISI marked) with all fittings such as tees, bends etc including sunk type pressed steel box covered with and including 3mm thick new bakelite laminated sheet top cover "Hylam" complete, all as specified & directed. (Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BoQ' ).'

All as per item No 101.00 (here-in-before) but ceiling fan /exhaust fan point controlled by one Number one way switch complete, all as specified & directed.

All as per item No. 101.00 (here-in-before) but for one 5 Amp socket outlet on independent board controlled by one Number one way switch on independent board complete, all as specified & directed.

All as per item No. 101.00 (here-in-before) but for one 5 Amp socket outlet on the same board controlled by one Number one way switch on same board all as specified & directed.

All as per tem No 101 above but point wiring with 2.5 sq mm single core FRLS cables and earth continuity wire with 2.5 Sq mm single core cable for one 3 pin 15 Amps socket outlet point controlled by one nos, one way switch on indep bd complete all as specified and directed.

S&F switch piano flush type, single pole, one way, 5/6 Amp 230 volts all as specified and directed

S&F switch piano, flush type, single pole, one way, 15 Amp, 230 Volts all as specified & directed.

S&F flush type socket outlet multipurpose 3 Pin 5/6 Amp (with 2 pin 5/6 Amp outlet also) 230 volts AC complete all as specified and directed.

S&F flush type socket outlet multipurpose 3 Pin 15/16 Amp (with 3 pin 5/6 Amp outlet also) 230 volts AC complete all as specified and directed.

S&F lamp holder, insluated body, with back plate suitable for batten fittings & complete all as specified & directed.

S&F modular ceiling rose surface bakelite 65mm x 50mm, 3 terminals with back plate etc complete all as specified and directed.

S&F sheet metal enclosure distribution board SP&N, 8 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating Aluminium bus bar, complete all as specified & directed.

S&F sheet metal enclosure distribution board SP&N, 4 way, double door, powder coated, protection class IP-42, suitable for mounting MCB, DBs confirming to IS-13032, IS-8632, BS-5484 with min 200 Amp rating aluminium bus bar, complete all as specified & directed.

S & F MCB SP, 6 to 32 Amps 240 Volts , 'C' curve, 10 KA, IS-8828 marked for fixing in DB complete all as specified & directed. Note :-Make of MCB shall be same as that DB.

Supply and fixing MCB SPN 40 Amps to 63 Amps, 240 volts, 10 KA rupturing capacity, IS-8828 marked, of the under mentioned type and rating and fixing in DBs (DBs Catered separately in this schedule): Note Make of the MCB should be the same as that of DB

Supply & Fixing LED light Fitting 1x40W, decorative ultra slim square profile lighting fixture with extruded polycarbonate, environmental friendly, energy efficient complete all as specified and directed

Supply and fixing LED street light fitting 30/35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

Supply and fix exhaust fan 450mm sweep, Copper winding motor, steel body AC single Phase 230V, 50HZ, 1400RPM with blades, frame and louvers complete all as specified & directed.

S&F XLPE Insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mn 2 Core complete all as specified & directed.

Supply and fix electric water heater, storage type mild steel with glass lined coating (Outer Body) with Titanium armour technology inner tank coating for preventing to corrison rusting and heating element upto 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV connection since etc.

Supply and laying double wall corrugated pipe (DWC) confirming to IS 19430 Part -I of size 50mm outer dia and 38mm inner dia complete all as specified and directed.

S&F ceilling fan regulator electronic step type of suitable wattage 230V suitable for 1200/1400 mm sweep ceiling fan etc complete all as specified and directed.

S&F ceilling fan 1200mm sweep, copper winding motor with down rod, canopy, rubber reel with three blade etc including provision of three single core 0.5 sqmm copper conductor flexible size MS bolts, nuts for fixing ceiling fan complete all as specified & directed.

Balaji Construction Co. (BID ID -3406513)

M/S SM BUILDER CO (BID ID -3407233)

M/S KAVITA CONSTRUCTION (BID ID -3406881)

VIKAS INFRASTRUCTURE (BID ID -3414199)