REPAIR/ MAINT OF PLASTERING, FLOORING, PERIODICAL SERVICES, SANITARY FITTINGS AND MISC B/R WORKS TO E/S INSTALLATIONS UNDER GE (U) MEERUT CANTT.

Amount

Demolition of brick work or stone /boulder masonry, built in cement mortar, including all quoins, arches, pillars etc but excluding ashlar facing, dressed stone work and precast concrete articles etc, complete all as specified and directed by Engr-in-charge.

Demolition of cement concrete (unreinforced) in ground floor and in pavings not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed by Engr-in-charge.

Plain cement concrete, (Nominal mix), type B-1, 1:2:4 (using 20mm graded crushed stone aggregates) as in cills, coping, apex stone, bed plates and lintel upto 1.6m clear span etc including weathering slightly rounded or chamfered angles and throating as directed including necessary form work, complete all as specified and directed by Engr-in-charge.

Brick work with flyash bricks straight or curved on plan, exceeding 6 m mean radius with old size bricks, built in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

All as per item No 04 here-in-before but except bricks, complete all as specified and directed by Engr-in-charge. Note : Old bricks obtained against demolition shall be used.

S&F 2nd class hard wood (sal/hollock), glazed and skelton shutters 35mm thick open rebated and prepared to receive glass, gauge,etc. (without sash bars), edges of framing palin, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Pt-I Section 8.24(a) supplied and fitted to chowkhats complete including fixing only iron mongery such as tower bolt,handle,hinges,aldrop bolt etc all as specified.

S&F factory made, 2nd class hard wood (sal/hollock), plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides, the side of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated, 35 mm thick complete including fixing only iron mongery such as tower bolt,handle,hinges,aldrop bolt etc all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) not exceeding 1.50 Sqm each, and removing from site, complete all as specified and directed by Engr-in-charge.

Taking down chowkats or frames including shutters (without taking off shutters from the frames) exceeding 1.50 Sqm but not exceeding 4 Sqm each, and removing from site, complete all as specified and directed by Engr-in-charge.

Taking down shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each, and removing from site, complete all as specified and directed by Engr-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tube for top & bottom rails. M.S. frame shall be covered with heat mouleded plain colour PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail. Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixed in the frame at site as per specification clause No.8B.1 to 8B.10 and drawing on page No. 146 of MES SSR-2004 Part-II complete including fixing only iron mongery such as tower bolt,handle,hinges,aldrop bolt etc all as specified

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supply & fixing in opening as per specification & drawing shown in SSR Part-II, complete all as specified and directed by Engr-in-charge.

S&F aluminum handles cast type, anodised, 150mm size complete all as specified .

S&F100mm long Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, and directed by Engr-in-charge.

S&F of 200 mm long mild steel barrel tower bolts, stove enameled black, with bright bolt all as specified.

S&F of mild steel sliding door bolt plate type 250 mm long stove enameled black with bright bolt not less 12 mm dia bolt with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified .

S&F of mild steel sliding door bolt plate type 300 mm long stove enameled black with bright bolt not less 12 mm dia bolt with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified .

S&F aluminum anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified .

M&L for providing cement concrete type C-1 1:3:6 using 20 mm graded crushed stone aggregates for filling in the pressed steel door frame/hold fast complete all as specified.

S&F of stainless steel wire cloth cut to size, 0.36 mm nominal dia wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staple complete all as specified .

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with stainless steel staple complete all as specified and directed by Engr-in-Charge.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in -Charge

M&L for Mild steel framed work such as grills, gratings with ends of bars shouldered or reveted or forged into spikes, framed guard bars, iron doors, ladders, framed balusters, walk ways railings, framework of watertanks and similar work, conforming to Fe-290, Gde E-165, complete all as specified and directed by Engr-in-charge.

M&L for Pressed steel frames of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and tarring back side of frame, complete all as specified and directed by Engr-in-charge.

M&L for Pressed steel frames of size 125x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc and providing one shop coat of primer and taring back side of frame, complete all as specified and directed by Engr-in-charge.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed by Engr-in-Charge.

M&L prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick AZ 150 of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

M&L prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick AZ 150 of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by Engr-in-Charge.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed by Engr-in-charge.

Rolled mild steel work as in roof trusses(framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing(Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc conforming to grade Fe-420 W(Gde-E-50) quality-A, steel work duly painted with one shop coat of zinc chromate primer incl preparation of surfaces all as specified.

Dismantling post or struts (wood, steel or RCC) any position, including taking out embeded portion,concrete, brick work, masonary etc and making good disturbed ground complete all as specified and directed by Engr-in-Charge.

Dismantling fencing wire, chain link, mesh fencing or any type and any position etc complete all as specified and directed by Engr-in-Charge.

Dismantling barbed wire of any description complete all as specified and directed by Engr-in-Charge.

M&L for hand rails, half rounded or other stock section or core for wooden hand rail straight portion, drilled and countersunk for balusters running bars, for door,balusters, noising to steps including embedding in concrete and screweing etc wind ties including securing bolts post and struts in fencing drilling holes,notching for wire etc flat iron fillets including necessary drilling, bolting and reveting etc or similar works complete all as specified and directed by Engr-in-Charge.

M&L for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc complete all as specified and directed by Engr-in-Charge. (each line wire to be measured).

M&L for Mild Steel round bars Fe-410-W (Gde E-250) quality-A or Fe 290 (Gde E-165) for securing chain link fencing complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete etc complete all as specified and directed by Engr-in-Charge.

M&L for Mild Steel nuts and bolts of size 12mm dia bolt exc 5cm but not exc 10cm long etc and dia of neck 10mm complete all as specified and directed by Engr-in-Charge.

S&F chain link fencing 4mm dia bar and mesh size 100x100mm complete including line wires of any mesh size and to any type of standards rails,straining bolts etc including provisioning of binding wire complete all as specified and directed by Engr-in-Charge.

Dismantling wall and ceiling boards any thickness, including cover fillets etc, complete all as specified and directed by Engr-in-charge.

S&F GI frame work 605x605mm for seamless ceiling comprising of GI perimeter channel 0.55mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit / tie / purlins etc, at approx 900 mm centre to centre with GI cleat and steel suspenders of appropriate size fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including provision of 4 mm thick non-asbestos fibre cement board, ISI marked, fixed to snap grid frame works 605 x 605 mm as in ceiling, flat or sloppy as per manufacture's instructions, complete all as specified and directed.

Dismantling floor , hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

M&L for Glazed ceramic coloured tiles 300mm x 200mm x 7/450X250x7 mm thick as in vertical surfaces such as skirting dado etc set and jointed in neat cement slurry, pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 to receive tiles, complete all as specified and directed by Engr-in-charge.

M&L for Non skid coloured 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over 15mm thick screed bed in CM 1:6, complete all as specified and directed by Engr-in-Charge.complete all as specified and directed by Engr-in-Charge.

M&L for Coloured chequered cement concrete tiles, machine pressed, factory made of size 250 x 250 x 22mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry, laid in floors, over and including 15mm thick screed bed in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

M&L for 75mm thick , Plain cement concrete, (Nominal Mix), Type C-2, 1:3:6 (using 40mm graded crushed stone aggregates) as in floors finished rough surface to receive floor finishes, complete all as specified and directed by Engr-in-charge.

M & L for 100mm thick PCC type D-2 1:4:8, using 40mm graded crushed stone aggregate as in flooring finished even and smooth without using extra cement with spike rolling to surfaces or making impression of expanded metal, whilst the concrete is green all as directed by Engr-in-Charge.

Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water complete all as specified.

M&L for 15 mm thick rendering on fair faces of brick or stone/concrete surfaces in cement mortar 1:4 and finished surface even and smooth without using extra cement complete with water proofing compound as per manufacturer instructions complete all as specified and directed.

M&L for 10 mm thick rendering on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified.

M&L for 5 mm thick rendering on fair faces of brick /concrete surfaces as in ceiling in cement mortar 1:3 and finished even and smooth without using extra cement complete all as specified.

M&L for applying two coat of oil bound distemper on walls after preparation of newly plastered surfaces over a coat of 1mm thick wall care putty, complete all as specified.

M&L for applying three coats of white washing on ceiling including preparation of newly plastered surfaces complete all as specified.

M&L for applying two coats of external Weather proof emulsion paint on walls after preparation of newly plastered surfaces over a coat of 1mm thick wall care putty, complete all as specified.

M&L for Preparation of new wooden surfaces of any description not otherwise described, exc 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed by Engr-in-charge.

M&L for Preparation of new steel surfaces of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as specified and directed by Engr-in-charge.

M&L for precast cement concrete jallies 25mm thick (measured solid set in cement mortar 1:4 incl all moulding and necessry form work, complete all as specified and directed by Engr-in-charge.

M&L, for machine pressed precast concrete interlocking paver block 60 mm thick,any shape and size confirming to IS-15658-2006,M-35 grade with grey cement and no pigment laid over old existing sand cushioning, complete all as specified.

Taking down steel rolling shutters manually operated type with ball bearing cover hood and channel, anchoring rod etc of size upto 25 sqm each complete all as specified and directed by Engr-in-Charge.

M&L for Steel rolling shutters 1.25mm thick without ball bearing, as specified including top cover, anchoring rod, hasp & staple & one shop coat of primer; erected in position as indicated, complete push pull or manual type complete all as specified and directed.

S&F safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed by Engr-in-Charge.

S&F Ball bearing for rolling shutters as per existing complete all as specified and directed by Engr-in-Charge.

Repairs to existing steel rolling shutters without ball bearing by taking down top cover, anchoring rod, spring etc and providing new springs and anchoring rod, replacing the worn out strips, safety lever lock of shutters and welding of handle, hasp staple and other broken articles etc, greasing the spring, guide rail, shaft etc and making functional and errecting in position, including refixing of top cover/hood etc, and refixing in same opening and making good in CM 1:3/PCC to match the existing surface, opening n.exc. 10 sqm each and finally painting with two coats of synthetic enamel paint, complete all as specified and directed by Engr-in-Charge.

M&L for cleaning the existing surfaces and removal of debris , loose particles , grass etc and existing water proofing roof treatment completely and repairing the cleaned surfaces through repair mortar and providing chemical injection grouting and angle filets ( if required ) and treatment of pipe entry with hybird PU sealant dual shrinkage compensated micro conrete. Applying priming coat of epoxy primer with resin hardner in 1:1 ratio with water dilution as per manufacturerinstructions applying 2 coats of solvent based polyrethane liquid membrane not less than 500 micron thick UV having SRI valve greater than eual to 105 with consumption of 0.61 kg/Sqm ( each coat), 2nd coat shuld be applied once 1st coat becomes dry completely including 40mm thick (average thickness) PCC 1:2:4 type B-1(using 20 mm graded stone aggregates) as in padding on roof finished even and fair without using extra cement and all as specified and directed.

M&L for prepration of old wooden surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified.

M&L for prepration of old steel/iron surfaces of any description not otherwise described over 10 cm width or grith and applying one coat of synthetic enamel paint complete all as specified.

M&L for preparation of old plastered/unplastered wall surfaces and applying one coat of cement base paint (including wahsing, rubbing down and stopping of distempered and painted surfaces), complete all as specifed.

Preparation of old plastered/unplastered wall surfaces and applying one coat of oil bound distemper over 1 mm thick wall care putty (including wahsing, rubbing down and stopping of distempered and painted surfaces), complete all as specifed.

M&L for new plastered surfaces applying Two or more coats of 100% Premium external weatherproof paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 1mm thick wall care putty. complete all as specified and directed.

Hacking out old broken glasses (any thickness, size, quality or description) from wooden frames or steel frames, glazed with putty or fixed with wooden beads, complete all as specified and directed by Engr-in-charge.

M&L for 3mm thick sheet glass ordinary quality, and glazing with oil putty or wooden beads in squares n.exc 0.50 Sqm in each pane, complete all as specified and directed by Engr-in-charge.

S&F in repair vitreous China wash basin, white, flat back, size 550x400mm excluding tap, chain, plug but including for fixing of taps,waste fitting, brackets and cutting for and pinning in ends of brackets but fixed in repair complete all as specified.

M&L for 10 litre capacity PVC, low level, valveless, syphonic action type flushing cistern, inlet ball valve, float valve, handle and fixing arrangement, 32 mm dia PVC flushing pipe and 15mm dia 450mm long PVC connection with CP brass coupling nuts and PVC washer at both ends (fixed in repair), complete all as specified and directed by Engr-in-charge.

S&F in repair stainless steel grade 304 conduit pipe 20mm bore (Drapery rod) with a pair of stainless steel clamps to hold drapary rod and decorative attachment at both ends of drapary rod, fixed to opening of door/windows, with a pair of clamps and a pair of side ornamental attachments), complete all as specified and directed by Engr-in-Charge.

S&F in repair pillar taps , cast copper alloy, with capstan heads , chromium plated , screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm complete all as specified.

S&F in repair PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified.

S&Fin repair waste fittings brass chromium plated for glazed ware sink, basins,etc with long screwed shank and fly nuts,flenges end bedded in red lead cement and other end fixed 32mm dia complete all as specified

S&F in repir stainless steel grating doom 100/150mm dia with or without hole complate all specified and directed.

S&F in repair 32/40 mm dia and 750mm long PVC waste pipe for WHB/sink complete all as specified

Taking up or down steel tubing with connections for cleaning for refixing or removing to storeyard complete of bore 15mm complete all as specified .

M&L for steel water tubing medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) of nominal bore 15 mm complete all as specified.

Refixing only Steel water tubing 15mm dia medium grade galvanised with all fitting and fixed complete to wall and ceiling or laid in floors all as specified.

S&F in repair plastic water closet seat cover, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device.

S&F in repair bib Tap of PTMT any colour 15mm dia complete all as specified and directed by Engr-in-charge.

Cleaning and removing all scale and dirt etc from PVC tank from mouths of circulating pipes capacity exc 250 ltr & not exceeding 500 ltr complete all as specified and directed by Engr-in-Charge.

S&F in repairs Rotational moulded polyethylene water storage tank 500 Ltrs capacity, ISI marked (cylindrical vertical with closed top), double wall layer construction, hoisted and fixed in position complete all as specified in SSR Part-I, making connections incl 20mm bore ball valve brass with polyethylene float and fly nut and tank nipples incl dismantling existing water tank of any capacity and removing from site, complete all as specified.

Supply and fixing in repair ball valves of size 20mm bore dia high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and directed

Supply and fixing in repair ball valves of size 15 mm bore dia high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (Minimum weight not less than 210 gms) screwed for iron pipe and fixed including necessary fitting as reqd at site complete all as specified and directed

Supply and fixing in repair angle valves cast copper alloy 15 mm, chromimum plated screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions including necessary fitting as required at site complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm dia stop cock fancy type chromium plated complete all as specified and directed.

S&F as in repair bib tap 15mm bore fancy type chromium plated all as specified.

S&F in repair bib cock 15mm bore fancy type long body chromium platedcomplete all as specified and directed.

S&F in repair Vitreous china, white, Squatting pan ,'Orrisa' pattern size 580x440mm with integral footrests water closet) , front or back inlet and incl PVC P and S trap, connection to drain pipe and to flushing pipe, including making good to floor to match with the exisitng all as specified.

S &F in repair Vitreous China white wash down water closet ( padestal pattern) , including fixing bolts, plastic closet seat, black, closed pattern with recessed bottom and cover, including connection to drain pipe, flushing pipe. etc complete all as specified.

AEGIS INTERNATIONAL (BID ID -3383884)

shiva construction and suppliers (BID ID -3374180)