PROVISION OF FLOOR TILES AND WALL TILES IN MD ACCN BLOCK NO P-245/1 TO 245/18 AND P-243/15 TO P-243/18 OF 11 CORPS PROVOST UNIT AT VAJRA COMPLEX AND CERTAIN REV WORKS IN THE AOR OF AGE B/R-II UNDER GE (WEST) JALANDHAR CANTT

Amount

Surface dressing n. exc. 15cm deep and averaging 15cm deep in soft/loose soil complete all as specified and as directed.

Surface excavation n. exc. 30cm deep and averaging 15cm deep in soft/loose soil complete all as specified and as directed.

Excavation in post holes (or similar holes) in soft/loose soil each n. exc. 0.5Cum, getting out, returning, filling in, and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering and removing surplus soil to adistance n. exc. 50m and making good the disturbed surface complete all as specified and as directed.

Excavation in trenches not exc. 1.5 m wide and n. exc. 1.5m in depth for foundation, etc, or for shafts, wells, cesspits, manholes, pier holes etc. and getting out in soft/loose soil complete all as specified and as directed.

Returning filling in, including, spreading, leveling and well ramming in layers not exceeding 25cm complete all as specified and directed.

Removing excavated material to a distance n exc 50 metre and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15 cm thick below or above ground level complete all as specified and directed.

Material and labour for plain cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate as in foundations, filling, sunken floor and mass concrete complete all as specified and directed.

Material and labour for applying two coats of SHALIMAR SUPERCRETE/ NITOBOND water proofing coating on the entire surface of sunken portion complete all as specified and directed.

Material and labour for 15mm thick cement screed in cement mortar (1:3) with integral WPC FOSROC’s complast X 421 IC @ 130ml per bag of cement including a bonding coat of FOSROC’s Nito bond AR cement slurry/ STP No 1 liquid @ 200 ml per bag complete all as specified and directed.

Material and labour for cement concrete 1:3:6 type C-2 using 40mm graded crushed stone aggregate as in post holes/foundation filling/mass surface channel, drain and similar works etc, complete all as specified and as directed.

Material and labour for providing PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in roof curves, mud stopes, sunken floor rounded, coping, benching/ haunching, slightly rounded or chamfered angle and throating etc complete all as specified and directed.

Material and labour for hard core of broken stone or boulder of gauge n. exc. 63mm, deposited, spread and levelled in layers n.exc. 15cm thick, watered and well rammed to a true surface complete all as specified and directed.

Material and labour for 25mm thick cement concrete 1:2:4 type B-0, using 12.5mm graded crushed stone aggregate as in damp proof course, surface finished fair and even without using extra cement and applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m complete all as specified and directed.

Material and labour for cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregate as in sub base/foundation filling/mass concrete/sunken floor etc, complete all as specified and as directed.

Material and labour for 100mm thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate), as in sub floors, sub base; concrete surfaces finished even & fair to receive topping floor finish/layer all as specified and directed.

Material and labour for 100mm thick plain cement concrete 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub-base for floors, surface finished even and rough to receive top finish complete all as specified and as directed.

Material and labour for 75mm thick plain cement concrete 1:4:8 type D-2, using 40mm graded crushed stone aggregate as in sub-base for floors, surface finished even and rough to receive top finish complete all as specified and as directed.

Material and labour for 50 mm thick PCC (1:3:6) type C-2 using 40 mm graded stone aggregate as in plinth protection, laid in panels, concrete surfaces finished even & smooth without using extra cement complete all as specified and directed.

Material and labour for providing 35mm thick (measured solid) precast cement concrete louvres and jallies in PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregates) including all mouldings set in cement mortar (1:4), fixed in repairs complete all as specified and directed .

Material and labour for reinforced cement concrete 1:2:4 type, B-1 (20mm graded graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and as directed.

Material and labour for reinforced cement concrete 1:2:4 type B-1, using 20mm graded stone aggregate as in roof kerbs, mud stops, coping/ benching/bed plates/plinth band lintles etc. and similar work including weathering, slightly rounded or chamfered edges and throating including necessary form work complete all as specified and as directed.

Material and labour for brick work with sub class 'B' bricks, straight or corvered on plan exc. 6.0m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Material and labour for brick work with sub class 'B' bricks, straight or corvered on plan exc. 6.0m mean radius built in cement mortar 1:4 complete all as specified and as directed.

Material and labour for brick work with fly ash bricks, straight or corvered on plan exc. 6.0m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Material and labour for form work to soffits of suspended slabs such as roof slabs, floor slabs, shelves, landing and similar work not exceeding 200mm thick (horizontal or sloping) and to edges of concrete surface fair finished complete all as specified and as directed.

Material and labour for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.surface fair finished complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each and refixing in same opening after doing necessary repair like cutting , change of position of hinges and making good to the old surface etc complete all as specified and directed

Taking down Chowkhat or frames not exceeding 1.5 Sqm each with shutters (Without taking off shutters from the frames complete all as specified and directed.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

Supply and fixing Factory made solid panel PVC door shutters 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site, complete all as specified and directed.

Material and labour for 35mm thick factory made plain framed, panelled shutters (two panels), with lock rail and panels of 9mm thick BWP commercial ply or of venered particle board 12mm thick with commercial veneering on both faces with rails and style of 2nd class hard wood. The size of rail and stile as per IS: 1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Material and labour for 2nd class hard wood factory made glazed and skeleton shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in clause 8.24 (a) of SSR Part-I; supplied and fitted to chowkhats complete all as specified and directed.

Supply and fixing 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, cast type, anodised, oval type, 150mm size, all as specified and directed.

Supply and fixing 200mm aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed.

Supply and fixing 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Material and labour for preparation of new or previously untreated wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed.

Material and labour for framed work as in doors , gates , guard bar etc of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing Fe 410-W (Gde-E-250) Quality A complete all as specified and as directed.

Material and labour for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 Quality A complete all as specified and as directed.

Material and labour for mild steel high yield strength TMT bars 10mm dia and over cut to length bent to shape required, including cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

Supply and fixing for rolled MS joist, channel, angle or tee sections, fixed independently, without connecting plates, etc (cut to ordinary length i.e. within 20mm of the length indcated) using Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed.

Supply and fixing steel work in tubular truss/purlins/rafters including special shaped washer etc. complete using ERW or including butt welded tubes conforming to IS 1161- 1979 grade St. 240 complete all as specified.

Supply and fixing MS plate (plain or cheuered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W (Gde E-250) complete all as specified.

Supply and fixing for steel window 1.25 mm thick box type (primer coated) ERW hollow P section of size 60mmx25mm single rebated comprises gauged skeleton shutter ERW sec 50mmx20mm and 1mm thick with two openable leaf consisting two Nos sash bars of T-section 20mmx3mm complete welded to frame with one verticle mulion of ERW box type T-section of size 60mmx25mm and 1.25mm thick incl cutting holes and making good dismantled portion PCC (1:2:4) type B-1 four Nos for each window) including following fittings welded to frame shutter: - (a) Hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window. (b) Handle of z section 20mmx25mm, 100mm long 01 Nos per leaf (c) MS tower bolt 150mm long-2 Nos per leaf (d) z section 20mmx25mm, 100mm long stopper - 01 No per leaf (f) MS pintal hinges of size 75mmx12mm- 2 Nos per leaf (g) Fabrication & fixing arrangement as per Drg No CEJZ/TD-06/07. Note: Wire mesh and painting shall be measured and paid separately under respective item of schedule.

Ditto all as per description ser item No- 45 but window with glazed shutters. Note : Glass pans and painting shall be measured & paid separately under respective item of schedule.

Material and labour for 3mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

Supply and fixing galvanised mild steel wire clothes 0.56 mm nominal dia of wire and average width of aperture1.18 mm complete fixed with tinned tacks or galvanised wire staples all as specified and as directed.

Material and labour for preparation of new steel surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fixing Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for 600x600x 4mm thick HSPC (High pressure steam cured) pre-laminated self embossed, textured designeer board to be fixed & including GI powder coated grid/section of size 600x600mm with main runner 38x24x0.9mm thick, cross tee 28.6x24x0.9mm and wall angle 19x19x0.9mm duly suspended with 4mm dia GI wire hangers 1200mm centre to centre both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including making arrangements for provisions of light fixtures of any size complete all as specified and directed by Engr-in-Charge.

Material and labour for roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and directed.

Material and labour for 25mm thick cement concrete 1:2:4 type B-0, using 12.5mm graded crushed stone aggregate as in levelling course, surface finished rough to receive topping floor/tiles complete all as specified and directed.

Material and labour for Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and directed.

Material and labour for Non skid ceramic coloured tiles 7 to 8mm thick (Square or rectangular) area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm, as in vertical surfaces i.e. skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10mm thick in cement mortar (1:4) finished rough to fix tiles complete all as specified and directed.

Material and labour for glazed ceramic coloured tiles, size 450mmx350mm/300mm x 200mm x 6-7mm thick as on vertical surfaces such as dado/skirting etc set and jointed in neat cement slurry and pointing in white cement with pigment to match the surface over and including 10 mm thick rendering or backing layer of cement mortar (1:4) complete all as specified and as directed.

Material and labour for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all specified and as directed.

Material and labour for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

Material and labour for 60 mm thick, machine pressed precast concrete interlocking paver block M-35 grade, any shape and size, conforming to IS 15658-2006, with grey cement and no pigment, complete all as specified and as directed.

Material and labour for chequered cement concrete tiles 30cm x30cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors laid over and including 20mm thick screed bed or bedding layer in cement mortar 1:6, set and jointed in neat cement slurry and pointing in white cement with pigment to match complete all as specified and directed.

Material and labour for precast cement concrete block masonry with solid blocks type B-1, 1:2:4 (20mm graded stone aggregate) exc 10 cm in width and set in cement mortar 1:6 for road edging complete all as specified and directed.

Material and labour for 15mm thick rendering in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all specified and as directed.

Material and labour for 15mm thick rendering in cement mortar 1:6 on other than fair faces of concrete on roof surfaces finished even and smooth without using extra cement complete all specified and as directed.

Material and labour for preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

Material and labour for preparation of new plastered surfaces of walls and applying three coats of white wash etc complete all as specified and directed.

Material and labour for preparation of old surface of wall and applying two coats of oil emulsion distemper complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connection including cleaning for refixing or removal to store complete all as specified and directed.

Supply, laying, jointing and testing 15mm bore galvanized iron steel tubing medium grade with all fittings such as bends, elbows, sockets, tees, reducers etc, fixed to walls, ceiling or laid in floors, including cutting through wall complete all as specified and as directed.

Material and labour galvanised iron tubes 20mm bore, medium grade with & including all fittings fixed to wall, ceilings and or laid in floors etc complete all as specified and directed.

Refixing old 15mm bore steel tubing and connections in new or old position (Walls, ceiling, floors, etc.) complete all as specified and as directed.

Cutting chases, pinning in, making good to facing where reqd and pointing in CM 1:3 to ends of edges of landing etc and cutting chases for concealed water tubing and making good cutting exc 10 cm but n.exc 20 cm girth complete all as specified and directed.

Supply and fixing in repairs bib taps, cast copper alloy, with crutch or butterfly handles, long body, fancy type, chromium plated screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

Supply and fixing in repair 15mm bore stop valve/angle cock fancy type cast copper alloy chromium plated (Concealed) screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed.

Supply and fixing in repair 15mm bore stop valve/angle cock fancy type, cast copper alloy, chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete all as specified and as directed.

Supply and fixing pillar tap, cast copper alloy chromium plated, with capston heads, 15mm bore dia of pipe screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and directed.

Supply and fixing in repair CP shower rose brass chromium plated square type of size 125mm with or without swivel joints including fixing to steel pipe or union of 15mm bore complete all as specified and directed

Supply and fixing for PVC connection 15mm bore size with PTMT nuts of length 450mm complete all as specified and directed.

Supply and fixing in repair vitreous china wash down water closet pan (pedestal pattern), white, and connection to drain (or outgoing pipe) and connection to flushing pipe, anti-syphonage pipe, (excluding flusing cistern and flush pipe) etc complete all as specified and as directed.

Supply and fixing plastic water closet seat cover (white) closed pattern with flat bottom and cover and mild steel chromium plated hinging device, fixed in repairs all as specified and directed.

Supply and fixing in repair brass chromium plated jet china wash down water closet pan (pedestal pattern) with flexible pipe of suitable length etc complete all as specified and as directed.

Supply and fixing in repair 10 litres capacity PVC valveless syphonic action type, low level flushing cistern ISI Marked white with inlet, ball valve, float and handle including brackets fixed complete all as specified and as directed.

Supply and fixing vitreous china wash hand basin, white, flat back 550 x 400mm excluding taps, waste chain and plug and porcelain stopper but including cast iron cantilever brackets and cutting for and pinning in ends of brackets complete all as specified and directed.

Supply and fixing vitreous china bowl urinal, half stall, (back or corner wall type) white complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2) securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, etc all as specified and directed.

Supply and fixing 32mm dia PVC waste pipe for wash hand basin complete all as specified and as directed.

Supply and fixing 32mm dia Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

Supply and fixing grating chromium plated 100mm dia with centre hole fixed in cement mortar 1:3 complete all as specified and as directed.

Supply, hoist and fixing in position, 500 litres capacity rotational moulded polythene water storage tank (cylindrical, vertical with closed top) ISI marked conforming to IS 12701, triple layered including supply and fixing 20mm dia, 450mm long GI washout pipe (medium grade) with plug and 20mm dia, 600mm long overflow GI pipe (medium grade) with all fittings complete all as specified and as directed.

Supply and fixing ball valve PTMT with epoxy coated aluminium rod and high density plastic ball complete screwed for 20mm bore dia of iron pipe or brass ferrule complete all as specified (Minimum weight 210 grams).

Supply and fixing 20mm gun metal globe or gate valve, with iron wheel head screwed both ends for iron pipe and fixed complete all as specifed and directed.

Supply and fixing brass chromium plated tubular towel rail 20mm dia, D type, 600mm long between flanges fixed complete all as specified and directed.

Supply and fixing stainless steel paper holder, fixed with gutties and steel screws on wall complete all as specified and directed

Supply and fixing stainless steel Soap dish, fixed to (walls) plugs with steel screws complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls or floors complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

Supply and fixing 110mm bore PVC (SWR) single 'T' , Equal & unequal complete all as specified and as directed.

Material and labour for 150mm bore salt glazed stone ware drain pipes (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as specified and directed.

Material and labour for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in concrete bed to 150mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Material and labour for cutting into existing manholes/ septic tank for connecting new drains, making good to open and rendering, cutting out existing benching for forming branch, channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-1 and making good pipe and reforming benching as required finishing even and smooth complete all as specified and directed.

Supply and fixing PVC (SWR) 'P' trap, including jointing with solvent cement diameter of outlet 75mm complete all as specified and as directed.

Material and labour for concealed point wiring with 1.5 Sq.mm (nominal area) single core PVC insulated and unsheathed, FRLS cable, multi-stranded, copper conductor cable 1100 Volts grade with universal colour code (Phase & Neutral), drawn in and including PVC concealed conduit medium grade (ISI marked) with accesories like bends, tee junction boxes fixed on wall, ceiling etc. with sunk mild steel pressed terminal box 1.6mm thick sheet duly painted with two coats of black bituminious paint over a coat of red oxide primer and providing 3mm thick laminated bakelite sheet top cover including earth wire of PVC insulated FRLS cable, copper conductor multi-stranded, 1.5 Sq.mm size in green colour, for one light/ one fan point controlled by one way switch complete all as specified and as directed.

Supply and fixing switch piano flush type, 5 Amps, AC, single pole, one way, 230 Volts (ISI Marked) complete all as specified and as directed.

Supply and fixing switch socket outlet multipurpose flush type 5 Amps, AC, 5 pin, single pole, one way, 230/250 Volts (ISI Marked) complete all as specified and as directed.

Supply and fixing lamp holder, PVC/Polycarbonate insulated body with back plate and LED bulb 5Watts suitable for batten fittings complete all as specified and as directed.

Supply and fixing ceiling rose, surface bakelite, 65mm x 50mm having 3 terminals, PVC polycarbonate and isolated body complete all as specified and as directed.

Supply and fixing sub main wiring with two single core PVC insulated unsheathed, FRLS multi stranded copper conductor cable of size 6.0 Sqmm and one single core PVC insulated unsheathed, FRLS multi stranded copper conductor cable green colour of size 6.0 Sqmm as earth lead in and including 25mm dia PVC concealed conduit with fittings complete all as specified and as directed.

Supply and fixing in replacement LED batten light fitting (double side) 1X22Watts decorative ultra slim aluminium square profile LED light fixture 6500K (white light) retrofit with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI with LED rod 22Watts with fixtures box type and making electrical connections to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75Sqmm 3 core complete all as specified and as directed.

Supply and fixing 300mm sweep metal body heavy duty exhaust fan, AC single phase 230/240 volts with louvers/shutter with mounting brackets with suitable size of nuts, bolts, washers make opening in the wall of required size for fixing the exhaust fan and making good the disturbed wall/plastered surface and making electrical connections to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 1.5Sqmm 3 core complete all as specified and as directed.

NIRMAL SINGH

Barmotra Infrastructures

SANDEEP JHANJI CONSTRUCTIONS

G S TRADERS

KAMAL AGGARWAL

SARASWATI CONSTRUCTION CO

PAUL CONSTRUCTION CO.

M/S Vinod Kumar

NATIONAL BUILDERS

M/S RAJESH CONSTRUCTION COMPANY

JAGDISH KUMAR SEHGAL

Motorway Constructions