CONSTRUCTION OF SHIVSRUSHTI, AT BARAMATI, TALUKA-BARAMATI, DISTRICT-PUNE.(Phase-I)

Amount

Excavation for foundation in earth, Soil of all types, sand, gravel and soft murum, including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m.) SSR 2022-23 Item No. 21.02 Sr.No. 721, Page No. 153, Bd.A.1 Page No. 259.

Excavation for foundation in Hard Murum including removing the excavated material upto distance of 50 metres beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting, dewatering etc. complete. (Lift upto 1.50 m) by Manual Means. SSR 2022-23 Item No. 21.05 Sr. No. 724, Page No.153, Bd.1 Page No. 259.

Excavation for foundation in Hard murum and boulders including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m ) SSR 2022-23 Item No. 21.10 Sr.No. 728, Page No. 154, Bd.A.3 Page No. 259.

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material up to a distance of 50 m. beyond the building area and stacking and spreading as directed, dewatering, preparing the bed for the foundation and necessary back filling with available earth / murum, ramming, watering including shoring and strutting etc. complete. (Lift upto 1.5 m ) SSR 2022-23 Item No. 21.14 Sr.No. 730, Page No. 154, Bd.A.4 Page No. 259.

Excavation for foundation in Hard rock by chiselling, wedging, line drilling etc including trimming and levelling the bed, removing the excavated material up to a distance of 50 m. beyond the building area and stacking as directed, dewatering, and back filling with available murum, ramming, watering etc. complete. (Lift upto 1.5 m) By Mechanical means. SSR 2022-23 Item No. 21.20 Sr.No.735, Page No. 155, Bd.A.6 Page No. 260.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper. SSR 2022-23 Item No. 21.22 Sr.No.737, Page No. 155, As directed by Engineer-In-Charge.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of Hephoclore per square metre of surface area covering ten years guarantee on bond paper. SSR 2022-23 Item No. 21.24 Sr.No.739 Page No.156, As directed by Engineer In Charge.

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30 -60 cm deep at 15 cm c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper, SSR 2022-23 Item No. 21.25 Sr.No.740, Page No. 156. As directed by Engineer in charge.

Filling in plinth and floors with approved excavated material in 15 cm. to 20 cm. layers including watering and compacting etc. complete.SSR 2022-23 Item No. 21.36 Sr.No.750, Page No. 157 Bd.A.10 Page No. 262.

Filling in plinth and floors with Contractors material / brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete. SSR 2022-23 Item No. 21.37 Sr.No.751, Page No. 157 Bd.A.11 Page No. 263.

Providing dry / trap /granite / quartzite Rubble Stone Soling 15cm to 20cm thick including hand packing and compacting etc. complete. SSR 2022-23 Item No. 21.38 Sr.No. 752, Page No. 157, BdA 12 Page No.264.

Providing Soling using 80mm size trap metal in 15cm layer including filling voids with Crushed Sand / Grit, ramming, watering etc. complete. SSR 2022-23 Item No. 21.40 Sr. No. 754, Page No.157, As directed by Engineer-In-Charge.

Providing and Fabricating Structural Steel Work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed, including cutting, fabricating, hoisting, erecting, fixing in position, making riveted / bolted / welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete. SSR 2022-23 Item No. 23.01 Sr. No. 816, Page No. 173, BdC 2 Page No.275.

Providing Structural steel work in Trusses, other similar trussed purlins and members with all bracing, gusset plates etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position, Making rivetted / bolted / welded connections and one coat of anticorrosive paint and over it two coats of oil painting approved quality and shade etc. complete. SSR 2022-23 Item No. 23.04 Sr.No.819, Page No. 173 BdC 8 Page No. 278.

Providing Structural steel work in Hollow Sections of various thickness and sizes in Square, Rectangular and Round shape from 25mm to 450mm section as per IS-4923 YST 310 Grade produced from iron ore and blast furnace route etc. as per detailed design and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, Making rivetted / bolted / welded connections and painting coomplete. SSR 2022-23 Item No. 23.12 Sr. No. 826, Page No. 174 As directed by Engineer-In-Charge.

Providing and laying Cast in situ/Ready Mix cement Concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 24.01 Sr.No.827, Page No. 175 Bd. E. 1 Page No. 287

Providing and laying Cast in situ/Ready Mixcement Concrete in M20 of trap/ granite/quartzite/gneiss metal for Steps / Screed / Grade Slab, including steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface, only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 24.06 Sr. No. 829, Page No. 175, Bd.E2 Page No. 288 and B7 Page No. 38.

Providing and laying Cast in situ/Ready Mix cement Concrete M-15 of trap/ granite/quartzite/gneiss metal for Coping to Plinth or Parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 24.16, Sr. No.835, Bd.E 3 Page No.288/ IS 456 (2000)

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. work in Foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork ,cover blocks, laying/pumping, compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) etc. complete, with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 25.13, Sr.No.837, Page No. 178 Bd.F.3 Page No. 298 and B.7, Page No.38.

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. work in Foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.19, Sr. No. 840, Page No.179, Bd.F 3, Page o.298 and B7, Page No. 38.

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawings or as directed including centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) , SSR 2022-23 Item No. 25.33, Sr.No. 842, Page No. 180 Bd.F.5 Page No. 300 and B- 7,Page No 38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawings or as directed including centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.33, Sr.No. 842, Page No. 180 Bd.F.5 Page No. 300 and B- 7,Page No 38. FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawings or as directed including centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) , SSR 2022-23 Item No. 25.33, Sr.No. 842, Page No. 180 Bd.F.5 Page No. 300 and B- 7,Page No 38. SECOND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawings or as directed including centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) , SSR 2022-23 Item No. 25.33, Sr.No. 842, Page No. 180 Bd.F.5 Page No. 300 and B- 7,Page No 38. THIRD FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawings or as directed including centering, formwork, cover blocks compacting and roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) , SSR 2022-23 Item No. 25.33, Sr.No. 842, Page No. 180 Bd.F.5 Page No. 300 and B- 7,Page No 38. FOURTH FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.39, Sr. No. 845, Page No.181, Bd.F 5 Page No. 300 and B7, Page No. 38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.39, Sr. No. 845, Page No.181, Bd.F 5 Page No. 300 and B7, Page No. 38. FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.39, Sr. No. 845, Page No.181,, Bd.F 5 Page No. 300 and B7, Page No. 38. SECOND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. Columns as per detailed designs and drawing or as directed including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.39, Sr. No. 845, Page No.181,, Bd.F 5 Page No. 300 and B7, Page No. 38. THIRD FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 25.52, Sr.No.847, Page No. 181, Bd.F.6 Page No. 300 and B.7, Page No.38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 25.52, Sr.No.847, Page No. 181, Bd.F.6 Page No. 300 and B.7, Page No.38. FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 25.52, Sr.No.847, Page No. 181, Bd.F.6 Page No. 300 and B.7, Page No.38. SECOND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 25.52, Sr.No.847, Page No. 181, Bd.F.6 Page No. 300 and B.7, Page No.38. THIRD FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 25.52, Sr.No.847, Page No. 181, Bd.F.6 Page No. 300 and B.7, Page No.38. FOURTH FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.58, Sr. No. 850, Page No. 182, Bd.F 6 Page No. 300 and B7 Page No. 38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.58, Sr. No. 850, Page No. 182, Bd.F 6 Page No. 300 and B7 Page No. 38. FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.58, Sr. No. 850, Page No. 182, Bd.F 6 Page No. 300 and B7 Page No. 38. SECOND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap / granite /quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.58, Sr. No. 850, Page No. 182, Bd.F 6 Page No. 300 and B7 Page No. 38. THIRD FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M - 25 of trap/granite/quartzite/gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, compaction, finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 202-23 Item No. 25.72, Sr.No.852, Page No.182, Bd.F.8 Page No. 302 and B.7, Page No.38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M - 25 of trap/granite/quartzite/gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, compaction, finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 202-23 Item No. 25.72, Sr.No.852, Page No.182, Bd.F.8 Page No. 302 and B.7, Page No.38. FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M - 25 of trap/granite/quartzite/gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, compaction, finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 202-23 Item No. 25.72, Sr.No.852, Page No.182, Bd.F.8 Page No. 302 and B.7, Page No.38. SECOND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M - 25 of trap/granite/quartzite/gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, compaction, finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 202-23 Item No. 25.72, Sr.No.852, Page No.182, Bd.F.8 Page No. 302 and B.7, Page No.38. THIRD FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.78, Sr. No. 855, Page No.183, Bd.F 8, Page No. 302 and B7 Page No. 38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.78, Sr. No. 855, Page No.183, Bd.F 8, Page No. 302 and B7 Page No. 38. FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete M-40 of trap/ granite / quartzite/ gneiss metal for R.C.C. slabs and landings as per detailed designs and drawings including steel centering, formwork, cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 25.78, Sr. No. 855, Page No.183, Bd.F 8, Page No. 302 and B7 Page No. 38. SECOND FLOOR

Providing and laying Cast in situ/Ready Mixcement concrete M- 25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 26.07, Sr.No. 857, Page No. 184, Bd.F.9 Page No. 303 and B.7, Page No.38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mixcement concrete M- 25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 26.07, Sr.No. 857, Page No. 184, Bd.F.9 Page No. 303 and B.7, Page No.38. THIRD FLOOR

Providing and laying Cast in situ/Ready Mixcement concrete M- 25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 26.07, Sr.No. 857, Page No. 184, Bd.F.9 Page No. 303 and B.7, Page No.38. FOURTH FLOOR

Providing and laying Cast in situ/Ready Mixcement concrete M- 40 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 26.07, Sr.No. 857, Page No. 184, Bd.F.9 Page No. 303 and B.7, Page No.38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mixcement concrete M- 40 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 26.07, Sr.No. 857, Page No. 184, Bd.F.9 Page No. 303 and B.7, Page No.38. FIRST FLOOR

Providing and laying Cast in situ/Ready Mixcement concrete M- 40 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete.With fine aggregate (Crushed sand VSI Grade), SSR 2022-23 Item No. 26.07, Sr.No. 857, Page No. 184, Bd.F.9 Page No. 303 and B.7, Page No.38. SECOND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 26.19, Sr. No. 861, Page No. 185, Bd.F 11, Page No.304 and Bd 7 Page No. 38. GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 26.19, Sr. No. 861, Page No. 185, Bd.F 11, Page No.304 and Bd 7 Page No. 38. FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Pardi of required thickness including steel centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 26.19, Sr. No. 861, Page No. 185, Bd.F 11, Page No.304 and Bd 7 Page No. 38. SECOND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and Steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 26.26, Sr. No. 864, Page No. 186, Bd.F 14, Page No.305 / IS 456 (2002). GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-25 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and Steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 26.26, Sr. No. 864, Page No. 186, Bd.F 14, Page No.305 / IS 456 (2002). FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-40 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and Steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 26.26, Sr. No. 864, Page No. 186, Bd.F 14, Page No.305 / IS 456 (2002). GROUND FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-40 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and Steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 26.26, Sr. No. 864, Page No. 186, Bd.F 14, Page No.305 / IS 456 (2002). FIRST FLOOR

Providing and laying Cast in situ/Ready Mix cement concrete in M-40 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and Steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Crushed sand VSI Grade) SSR 2022-23 Item No. 26.26, Sr. No. 864, Page No. 186, Bd.F 14, Page No.305 / IS 456 (2002). SECOND FLOOR

Providing and fixing in position TMT-Fe 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete, SSR 2022-23 Item No. 26.33, Sr.No.871, Page No. 188, Bd.F.17, Page No. 306. GROUND FLOOR

Providing and fixing in position TMT-Fe 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete, SSR 2022-23 Item No. 26.33, Sr.No.871, Page No. 188, Bd.F.17, Page No. 306. FIRST FLOOR

Providing and fixing in position TMT-Fe 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete, SSR 2022-23 Item No. 26.33, Sr.No.871, Page No. 188, Bd.F.17, Page No. 306. SECOND FLOOR

Providing and fixing in position TMT-Fe 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete, SSR 2022-23 Item No. 26.33, Sr.No.871, Page No. 188, Bd.F.17, Page No. 306. THIRD FLOOR

Providing and fixing in position TMT-Fe 500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete, SSR 2022-23 Item No. 26.33, Sr.No.871, Page No. 188, Bd.F.17, Page No. 306. FOURTH FLOOR

Providing and fixing of 65/400 Self supported Secret Fix ROOFING SYSTEM in 0.9mm thick in AA-5052 Aluminium Alloy including accessories and flashing comprising of following layers. System Warranty - 15 years and Leakage Warranty - 10 years. 1. Top Layer - Providing and fixing 65mm rib height and 400mm width of straight / curved / tapered profiled panel, manufactured from Aluminium Alloy AA-5052 as specified in BS ENI396:2007, minimum material thickness of 0.9mm with 60 microns Durabond / 60microns PVDF paint finish (colour as per Architect's choice). Aluminium sheet make, GRAMCO Baharain / Euramax E.U. / Hulemin South Africa / Hindalco India The profile should have Architectural mini ribs of 1.5mm to provide additional strength at the pan. The material properties shall be as follows: Ultimate Tensile Strength - minimum 200N/Sq.mm, 0.2% proof stress - min 185 N/Sq.mm, Modulus of Elasticity - 70000 N/Sq.mm. The system should be laid to meet the requirements of the building geometry and fixed on Aluminium clip / halter. The fixing halter shall be made of AA-6082 T6, in accordance with BSEN-755 Part-2, with ultimate tensile strngth not less than 340Mpa and elongation not more than 16% when tested according to ASTM B 557:1981. Each aluminium clip should come with a 6mm thick black polyamide thermal barrier pad with minimum tensile strength of 83 Mpa and maximum elongation of 10% in room temperature. The aluminium halters shall be capable of transmitting all reaction forces to the purlin without the aid of any other material, thus resulting in an overall “Self- supporting standing seam roof system”. Roofing system manufacturer shall be certified with ISO Certificate (ISO 9001). Aprooved Make - KALZIP / KINGSPAN. 2. Second Layer - Roxul-Rockwool Insulation of 150 mm thickness x minimum 60Kg/m3 density. Thermal Transmittance (U-value) to be 0.26W/m2.K. Calculation to be submitted in accordance with BS EN ISO 6946. Sound Transmission Class STC value 38±3 dB to achieve as per ASTM E 90-97. APPROVED MAKE: ROCKWOOL/ROXUL/ HITECH 3. Third Layer - Scrim reinforced Polyethylene film heavy duty type or double sided aluminium foil vapour control layer 170microns (VCL 170) thick should be laid providing a minimum water vapour resistance of 336MNs/g and water permeability of 0.61g/m2/day. 4. Fourth Layer - Supply & Fixing of WA200, RMR 1000 or equvivalent bare galvalume profile sheet of 1000-1015 mm effective cover width and 28-35 mm height ribs with subtle square fluting in the five pan at 200-250 mm centre-to-centre. The feed material is manufactured out of nominal 0.47mm Total Coated Thickness (TMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume/ Galvalume AZ150 (Min. 150 gms/sq.mt total on both sides) Fixed to the purlins with screws. Approved Makes - TATA Bluescope / JINDAL.

Providing and Fixing of in 0.9mm thick Aluminium Flashing (Specification same as Sr. No. 1.1 above) maximum width 500 mm. Colour to match to roofing material.

Providing and fixing of Single skin 2 mm Aluminium gutter, GRADE AA 1100 ALLOY with EPDM Expansion joints for every 12m length, aluminum Down take spout dia 150 mm at every 10 m gutter length, & other accessories and welding at joints. The Girth of gutter would be maximum 1200mm. With bare galvalume bottom sheet 0.47 mm thick, Rockwool insulation 150 mm thick & 60 kg/m3 density, vapour control layer - VCL 170, and z-girt galvanised steel 1.5mm thick.

Supply & Installation of CHECKLINE/LATCHWAYS / KINGSPAN /UDYOGI / KARAM FALL ARRESTER SYSTEMS with Topfix Post with patented rubber energy absorber suitable for Standing Seam Roofing sheets and fixed using 4 x aluminium clamps below 4 corners of the base plate. MANUFACTURED BY CHECKMATE LIFTING & SAFETY LTD., U.K. along with 2 nos of removable trolleys for max. 2 users. System to have CE mark and hold EC declaration of conformity. Must comply with BS EN 795 Class A & Class C and BS 7883. The Checkline Topfix posts with patented rubber energy absorber shall be fixed to the base plate made up of stainless steel powder coated along with 8mm diameter, 7x7 stainless steel wire rope. The system shall be configured with intermediate post, end post, corner post, stand alone, cross over post and T-junction post - which are made of stainless steel SS 316. The system shall have a unique load cell to maintain the tension on the Stainless steel wire rope between 40kg to 200kg and allow for thermal movement of the roof structure. The system's end connection to be connected to wire rope using Checkmate Modular Energy Absorber which shall have the ability to control maximum system forces to allow for fixing to different roof thicknesses. All end connection must be swagged on. The distance between two posts should not exceed more than 9 metres. The system length comprising start post to end post including all intermediate posts shall not exceed 200m (for straight line System) and 150 m (in case of bends/corners). Test report of salt sprays testing to 1000 hours with no corrosion shall also be provided. The system allows for multi-purpose brackets which can rotate through 180° and lock into position. The system shall allow for a range of multi-purpose corners, to suit any turn, corner, deviation or incline to suit the roof layout and design. The system shall consist of identity plates fixed to entry/exit post to indicating : Name and Address of the manufacturer, System type, Nos. of users, Test load, Serial Number, Date of installation and Next date of inspection. SYSTEM WARRANTY - 20 Years based on annual inspection by Checkline / KINGSPAN installer. APPROVED MAKES: CHECKLINE/LATCHWAYS/ KINGSPAN /UDYOGI / KARAM

SUPPLY & INSTALLATION OF GFRP WULMET / KINGSPAN / UDYOGI / KARAM WALKWAY along with accessories, that affix to the Metal Roof surface, as MANUFACTURED BY WULMET in Portugal shall be made with open moulded grating in Isophthalic resin. PRODUCT DESCRIPTION: The thickness shall be 25mm for 38mm X 38mm mesh -It shall have fixing feet suitable for standing seam of 400mm width Kalzip/Kingspan is with Anti slip surface with sand grit finish suitable for all types of industrial footwear. It shall be tested to EN516-1, with Class 1 fire rating and have a CE Declaration of Performance Certificate. The grating shall be in Grey colour There shall be suitable perforations in the walkway to allow for water dissipation The length of each walkway panel widths from 250 mm. The walkway system shall to be installed up to a roof slop of 45degree by means of adjustable semi-circular disc. The walkways shall sustain a load of 150kg on an area of 100mm X 100mm with less than 15mm of deflection or 1/100 of the span. whichever is lesser. The walkway shall be fixed to the roof surface GFRP walkway which can be adjusted on site to account for different inclines at 2.5 degree intervals. All fasteners to be stainless steel grade SS 304. Note : Product life span of 20 years and system warranty of minimum 10 years to be provided.

Providing and Fixing Mangalore Tile Roofing with class AA Tiles in cement mortar 1:4 on Sloping Slab including necessary scaffolding, curing finishing etc. complete. SSR 2022-23, Item No. 38.33, Sr. No. 1173, Page No. 236, Bd. R3A, Page No. 449.

Providing and fixing Mangalore tile ridge and hip tiles of class 'AA' including scaffolding if necessary, pointing with coloured cement mortar and curing etc. complete. SSR 2022-23, Item No. 38.03, sr. No. 1143, Page No. 233, Bd. R3, Page No. 450.

Providing and Fixing False Ceiling with eco-friendly light-weight Calcium Silicate Tiles of spintone surface texture Aerolite make or equivalent of size 595mm x 595mm having 15mm thick densified micro look edge and 100%humidity resistance incombustible as per BS 46 part IV and thermal conductivity 0.043 with o KC and NRC 0.50 placed in true horizontal level suspended grid of size 600mm x 600mm made from hot dipped GI steel sections ion silhouette profile, rotary stitched double webbed white with 6mm reveal profile (white/black), wherein, main T runner of size 42mmx14mm between main tee 600mm center- tocenter and secondary cross T of size 33x14x0.43mm thick of length 600mm long spaced inter-locked at middle of the first crossed T in each panel to form grid of 1200mmx600mm resting on periphery wall Profile wall section 19mm (7+7) x 19mmx0.40thicknesses and laying false ceiling for services like diffusers grills including cutting, making opening for light fittings, fixtures, , smoke detectors etc., wherever required. Main T runners suspended from ceiling with using G.I. soffit cleats of size 25x35x1.6 mm of required length fixed to the ceiling with 6mm dia and 50mm long dash fastener, 4mm dia G.I. adjustable rods with powder- coated/good quality G.I. level adjustment clips of 35x35x0.8mm spaced SSR 2022-23, Item No. 38.40, Sr.No. 1180, Page No. 238, As directed by Engineer-In-Charge.

Providing and fixing in position Gypsum board False Ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. SSR 2022-23, Item No. 38.51, Sr.No. 1191, Page No. 243, As directed by Engfineer-In-Charge.

Providing Fly Ash Brick Masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in foundation and plinth including bailing out water manually striking joints, racking out joints watering and scaffolding etc. complete. SSR 202-23, Item No. 27.12, Sr. No. 899, Page No.198, As director by engineer in charge and BDG- 2 and 5

Providing Fly Ash Brick Masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in Superstructure including striking joints, racking out joints watering and scaffolding etc. complete. SSR 2022-23, Item No. 27.13, Sr.No.900, Page No.198 As director by engineer in charge and BDG-2 and 5. GROUND FLOOR

Providing Fly Ash Brick Masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in Superstructure including striking joints, racking out joints watering and scaffolding etc. complete. SSR 2022-23, Item No. 27.13, Sr.No.900, Page No.198 As director by engineer in charge and BDG-2 and 5. FIRST FLOOR

Providing Fly Ash Brick Masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in Superstructure including striking joints, racking out joints watering and scaffolding etc. complete. SSR 2022-23, Item No. 27.13, Sr.No.900, Page No.198 As director by engineer in charge and BDG-2 and 5. SECOND FLOOR

Providing Fly Ash Brick Masonry with conventional / I.S. type fly ash bricks in C.M. 1:6 in Superstructure including striking joints, racking out joints watering and scaffolding etc. complete. SSR 2022-23, Item No. 27.13, Sr.No.900, Page No.198 As director by engineer in charge and BDG-2 and 5. THIRD FLOOR

Providing Second Class Fly Ash Brick Masonry with conventional / I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6mm diameter / two hoop iron strips 25mm x 1.60mm at every third course, properly bent and bounded at ends, scaffolding, raking out joints and watering etc. complete. SSR 2022-23, Item No. 27.14, Sr.No. 901, Page No. 198, Bd.G.7 Page 316. GROUND FLOOR

Providing Second Class Fly Ash Brick Masonry with conventional / I.S. type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6mm diameter / two hoop iron strips 25mm x 1.60mm at every third course, properly bent and bounded at ends, scaffolding, raking out joints and watering etc. complete. SSR 2022-23, Item No. 27.14, Sr.No. 901, Page No. 198, Bd.G.7 Page 316. FIRST FLOOR

Providing Uncoursed rubble masonry of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in foundation and plinth of inner walls / in plinth of external walls including bailing out water manually , striking joints on un exposed faces and watering etc.complete. SSR 2022-23, Item No. 28.01, Sr. No. 904,Page No. 199, BdH 1 Page No.329.

Providing Coursed Rubble Masonry First Sort of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in exterrnal work of Plinth including bailing out water manually, striking joints inside and watering etc. complete. SSR 2022-23, Item No. 28.11, Sr. No. 914,Page No. 200, BdH 13 Page No.333.

Providing Coursed Rubble Masonry First Sort of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in Superstructure including racking out joints inside when plastering is to be done, watering and scaffolding etc. complete. SSR 2022-23 Item No. 28.12, Sr. No. 915, Page No. 200, BdH 14 Page No.333. GROUND FLOOR

Providing Coursed Rubble Masonry First Sort of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in Superstructure including racking out joints inside when plastering is to be done, watering and scaffolding etc. complete. SSR 2022-23, Item No. 28.12, Sr. No. 915, Page No. 200, BdH 14 Page No.333. FIRST FLOOR

Providing Coursed Rubble Masonry First Sort of trap / granite / quartzite / gneiss stones in cement mortar 1:6 in Superstructure including racking out joints inside when plastering is to be done, watering and scaffolding etc. complete. SSR 2022-23 Item No. 28.12, Sr. No. 915, Page No. 200, BdH 14 Page No.333. SECOND FLOOR

Providing First Class Brick Masonry with conventional / wire-cut / IS type bricks in cement mortar 1:4 including scaffolding, racking out joints, pointing in cement mortar 1:3 and watering etc in pillars / walls of curved shapes, as shown in the drawing or as directed by Engineer-In-Charge, etc. complete. SSR-2022-23, Item no. 27.09, Sr.No. 896, Page No. 197, Bd.G-9(b), Page No.317.

Providing Ashlar Masonry with Soft Compacted Basalt stone. First Sort like walls, columns, cap stones etc. with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper), setting with stainless steel dowels, pins and fixing with Araldite and hardner etc. including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulded stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing Composite Masonry with Soft Compacted Gokak Stone. First Sort and First Class Brick Masonry with conventional / wire-cut / IS type bricks for walls, Curved Walls, columns, cap stones, composite walls etc. with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper), setting with stainless steel dowels, pins and fixing with Araldite and hardner etc. including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulded stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. SSR 2022-23, Item No. 31.04, Sr.No.940, Page No. 205,BDJ- As directed by Engineer in charge. GROUND FLOOR

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. SSR 2022-23, Item No. 31.04, Sr.No.940, Page No. 205,,BDJ- As directed by Engineer in charge. FIRST FLOOR

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1Kilogramper bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. SSR 2022-23, Item No. 31.04, Sr.No.940, Page No. 205,,BDJ- As directed by Engineer in charge. SECOND FLOOR

Providing Waterproof Plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete. SSR 2022-23, Item No. 31.07, Sr.No.943, Page No.206, BDJ As directed by Engineer in Charge. GROUND FLOOR

Providing Waterproof Plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete. SSR 2022-23, Item No. 31.07, Sr.No.943, Page No.206, BDJ As directed by Engineer in Charge. FIRST FLOOR

Providing Waterproof Plaster in W.C. and bath 20 mm thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 kg. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete. SSR 2022-23, Item No. 31.07, Sr.No.943, Page No.206, BDJ As directed by Engineer in Charge. SECOND FLOOR

Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for Terrace Waterproofing on B.B. Coba / R.C.C, after application of TP- 42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms/Square Metre and applying 2nd coat of Polydee-LM @ 700 gms/Square Metre and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/Square Metre to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete. SSR 2022-23, Item no. 31.10, Sr.No.946, Page No. 206, BDJ- As directed by Engineer in charge. GROUND FLOOR

Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for Terrace Waterproofing on B.B. Coba / R.C.C, after application of TP- 42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms/Square Metre and applying 2nd coat of Polydee-LM @ 700 gms/Square Metre and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/Square Metre to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete. SSR 2022-23, Item no. 31.10, Sr.No.946, Page No. 206, BDJ- As directed by Engineer in charge. SECOND FLOOR

Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for Terrace Waterproofing on B.B. Coba / R.C.C, after application of TP- 42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms/Square Metre and applying 2nd coat of Polydee-LM @ 700 gms/Square Metre and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/Square Metre to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete. SSR 2022-23, Item no. 31.10, Sr.No.946, Page No. 206, BDJ- As directed by Engineer in charge. THIRD FLOOR

Providing and laying jointless Polydee-LM, a highly flexible elastometric coating for RCC / cementitious surface for Terrace Waterproofing on B.B. Coba / R.C.C, after application of TP- 42 Primer on perfectly clean surface (free from loose dust and foreign matter) application of 1st coat of Polydee-LM @ 700 gms/Square Metre and applying 2nd coat of Polydee-LM @ 700 gms/Square Metre and finishing the same with sprinkling the AG-10 granules on the wet coating. (After finishing covering the treatment with 25mm cement plaster for protection with fibrillated 6mm Plyplast fibre @ 125 gms/Square Metre to be paid in separate item.) covering 7 years guarantee on Court Fee Stamp Paper of Rs. 100/- etc. complete. SSR 2022-23, Item no. 31.10, Sr.No.946, Page No. 206, BDJ- As directed by Engineer in charge. FOURTH FLOOR

Providing and Fixing 20 to 25mm thick Rough Shahabad Box Type Waterproofing for basement or underground floor on a base of cemenrt concrete 1:3:6, including sub base of 2.50 centemeter thick cement mortar 1:3 with conceal secrete (RMW), Algae proof or other alike waterproofing liquids, racking of joints upto 35mm depth, filling the joints with 6mm size crushed metal, hand grouting with cement slurry, curing and cleaning with 7 years guarantee on Court fee stamp paper of Rs.100/- with ponding test etc. complete. (excluding cement concrete 1:3:6 base concrete). SSR 2022-23, Item No. 31.12, Sr. No.948, Page No. 206, BdJ 2 Page No.355.

Providing and Fixing 20 to 25mm thick Rough Shahabad Box Type Waterproofing treatment to Vertical outside faces of reinforced cement concrete walls of basement or underground floor including filling the gap of 25mm between rough shahabad and R.C.C. walls with cement grout mixed with waterproofing liquid Algae proof or other alike with one tile lift method, brushing the joints horizontally with cement slurry mixed with waterproofing liquid for width 30 to 35mm and sloping coping over topmost tile with cement mortar 1:3, butting the bottom most with cement concrete 1:2:4 mixed with waterproofing liquid, curing with 7 years guarantee on Court fee stamp paper of Rs.100/- with ponding test etc. complete. (excluding cement concrete 1:3:6 base concrete). SSR 2022-23, Item No. 31.13, Sr. No.949, Page No.207, BdJ 2 Page No. 355.

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. SSR 2022-23, Item No. 31.26, Sr.No.954, Page No. 208, BDJ- As directed by Engineer in charge. GROUND FLOOR

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. SSR 2022-23, Item No. 31.26, Sr.No.954, Page No. 208, BDJ- As directed by Engineer in charge. FIRST FLOOR

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound @ 1Kilogram/per bag of cement laying brick bat coba of required thickness in cm 1:5 with waterproofing compound 1 Kilogram/bag of cement grouting and finishing the top layer with 20mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 Kilogram/per bag of cement and testing the treated portion for 48 hours by pond test and covering ten years' guarantee on requisite stamp paper including curing etc. complete. SSR 2022-23, Item No. 31.26, Sr.No.954, Page No. 208, BDJ- As directed by Engineer in charge. SECOND FLOOR

Providing internal cement plaster 20mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. SSR 2022-23, Item No. 32.07, Sr.No. 961, Page No. 209, Bd. L.4 Page No. 368. GROUND FLOOR

Providing internal cement plaster 20mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. SSR 2022-23, Item No. 32.07, Sr.No. 961, Page No. 209, Bd. L.4 Page No. 368. FIRST FLOOR

Providing internal cement plaster 20mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. SSR 2022-23, Item No. 32.07, Sr.No. 961, Page No. 209, Bd. L.4 Page No. 368. SECOND FLOOR

Providing internal cement plaster 20mm thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. SSR 2022-23, Item No. 32.07, Sr.No. 961, Page No. 209, Bd. L.4 Page No. 368. THIRD FLOOR

Providing Sand faced plaster Externally in cement mortar using approved screned sand in all positions including base coat of 15mm thick in cement mortar 1:4 using waterproofing compound of 1 kg per cement bag curing the same for not less than two days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for forteen days scaffolding etc. complete. SSR 2022-23, Item No. 32.11, Sr.No. 963, Page No. 209, BDL-7, Page No.369. GROUND FLOOR

Providing Sand faced plaster Externally in cement mortar using approved screned sand in all positions including base coat of 15mm thick in cement mortar 1:4 using waterproofing compound of 1 kg per cement bag curing the same for not less than two days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for forteen days scaffolding etc. complete. SSR 2022-23, Item No. 32.11, Sr.No. 963, Page No. 209, BDL-7, Page No.369. FIRST FLOOR

Providing Sand faced plaster Externally in cement mortar using approved screned sand in all positions including base coat of 15mm thick in cement mortar 1:4 using waterproofing compound of 1 kg per cement bag curing the same for not less than two days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for forteen days scaffolding etc. complete. SSR 2022-23, Item No. 32.11, Sr.No. 963, Page No. 209, BDL-7, Page No.369. SECOND FLOOR

Providing Sand faced plaster Externally in cement mortar using approved screned sand in all positions including base coat of 15mm thick in cement mortar 1:4 using waterproofing compound of 1 kg per cement bag curing the same for not less than two days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for forteen days scaffolding etc. complete. SSR 2022-23, Item No. 32.11, Sr.No. 963, Page No. 209, BDL-7, Page No.369. THIRD FLOOR

Providing and fixing chicken mesh of 22 gauge, with about 30cm width at the junction of RCC members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete / brick masonry and or tieing by binding wire etc. complete. SSR 2022-23, Item No. 32.26, Sr. No. 977, Page No. 210, As directed by Engineer-In-Charge. GROUND FLOOR

Providing and fixing chicken mesh of 22 gauge, with about 30cm width at the junction of RCC members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete / brick masonry and or tieing by binding wire etc. complete. SSR 2022-23, Item No. 32.26, Sr. No. 977, Page No. 210, As directed by Engineer-In-Charge. FIRST FLOOR

Providing and fixing chicken mesh of 22 gauge, with about 30cm width at the junction of RCC members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete / brick masonry and or tieing by binding wire etc. complete. SSR 2022-23, Item No. 32.26, Sr. No. 977, Page No. 210, As directed by Engineer-In-Charge. SECOND FLOOR

Providing and fixing chicken mesh of 22 gauge, with about 30cm width at the junction of RCC members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete / brick masonry and or tieing by binding wire etc. complete. SSR 2022-23, Item No. 32.26, Sr. No. 977, Page No. 210, As directed by Engineer-In-Charge. THIRD FLOOR

Providing and applying Gypsum Plaster ( with Gypsum material ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete. SSR 2022-23, Item No. 32.31, Sr. No. 982, Page No. 211, As directed by Engineer-In-Charge. GROUND FLOOR

Providing and applying Gypsum Plaster ( with Gypsum material ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete. SSR 2022-23, Item No. 32.31, Sr. No. 982, Page No. 211, As directed by Engineer-In-Charge. FIRST FLOOR

Providing and applying Gypsum Plaster ( with Gypsum material ) with finishing with gypsum material in 10 to 13 millimeter thickness to previously plastered surface / or on newly brick surface ( Excluding rough cast plaster ) in all position including preparing and Finishing the surface scaffolding etc.complete. SSR 2022-23, Item No. 32.31, Sr. No. 982, Page No. 211, As directed by Engineer-In-Charge. SECOND FLOOR

Providing and applying two coats of wall care putty on plastered surface and ceiling and walls to prepare surface even and smooth of approved make.etc Complete, SSR 2022-23, Item No. 32.34, Sr.No. 985, Page No. 212, As directed by Engineer-In-Charge. GROUND FLOOR

Providing and applying two coats of wall care putty on plastered surface and ceiling and walls to prepare surface even and smooth of approved make.etc Complete, SSR 2022-23, Item No. 32.34, Sr.No. 985, Page No. 212, As directed by Engineer-In-Charge. FIRST FLOOR

Providing and applying two coats of wall care putty on plastered surface and ceiling and walls to prepare surface even and smooth of approved make.etc Complete, SSR 2022-23, Item No. 32.34, Sr.No. 985, Page No. 212, Asdirected by Engineer-In-Charge. SECOND FLOOR

Providing and applying two coats of wall care putty on plastered surface and ceiling and walls to prepare surface even and smooth of approved make.etc Complete, SSR 2022-23, Item No. 32.34, Sr.No. 985, Page No. 212, As directed by Engineer-In-Charge. THIRD FLOOR

Providing and applying Texture plaster with finishing with texture material of approved make in 3 to 4 millimeter thickness on previously plastered surface, including Plaster Groove 6mm thickness or Tape Grooves 35 to 45 mm thickness or as required, in all position including preparing the surface, scaffolding etc. complete. SSR 2022-23, Item No. 32.32, Sr.No. 983, Page No. 211, As directed by Engineer-In-Charge.

Providing and laying Cement Concrete Flooring 50mm thick with M20 cement concrete laid to proper level and slope in alternate bays including compaction, filling joints, marking lines to give the appearance of tiles of 30cm x 30cm or other size laid diagonally/ square etc. finishing smooth (with extra cement) in any colour as directed and curing etc. complete.with Crushed sand VSI Grade. SSR 2022-23, Item no. 33.15, Sr. No. 1002, Page No. 214, Bd.M 6 Page No.381.

Providing and Laying in-situ Cement Concrete M30 with Tremix Treatment for Flooring for 200 milimeter thickness with groove cutting of 4mm wide and 20mm deep with necessary refilling with bitumen etc. complete. SSR 2022-23, Item No. 33.31, Sr.No.1018, Page No.216, As directed by Engineer-In-Charge.

Providing and laying in position Flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown Granite Stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. SSR 2022-23, Item No. 33.34, Sr. No. 1021, Page No.216, Bd.M 3B Page No. 380. GROUND FLOOR

Providing and laying in position Flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown Granite Stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. SSR 2022-23, Item No. 33.34, Sr. No. 1021, Page No.216, Sr. No. 1021, Page No.216, Bd.M 3B Page No. 380. FIRST FLOOR

Providing and laying in position Flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown Granite Stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in C.M. 1:3 curing and cleaning etc. complete. SSR 2022-23, Item No. 33.34, Sr. No. 1021, Page No.216, Bd.M 3B Page No. 380. SECOND FLOOR

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown Granite Stone for Treads and Risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. SSR 2022-23, Item No. 33.35, Sr. No. 1022, Page No. 216, Bd.M 22B Page No. 390. GROUND FLOOR

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown Granite Stone for Treads and Risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. SSR 2022-23, Item No. 33.35, Sr. No. 1022, Page No. 216, Bd.M 22B Page No. 390. FIRST FLOOR

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown Granite Stone for Treads and Risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. SSR 2022-23, Item No. 33.35, Sr. No. 1022, Page No. 216, Bd.M 22B Page No. 390. SECOND FLOOR

Providing and fixing machine cut mirror polished 18mm to 20mm thick Telephone black granite / Amba white / Cat bary brown / RBI red / Ocean brown Granite Stone Partitions with full moulding the edges etc. complete. Both side polish. SSR 2022-23 Item No.33.36, Sr. No. 1023, Page No. 216, Bd M35 B, Page No. 393. GROUND FLOOR

Providing and fixing machine cut mirror polished 18mm to 20mm thick Telephone black granite / Amba white / Cat bary brown / RBI red / Ocean brown Granite Stone Partitions with full moulding the edges etc. complete. Both side polish. SSR 2022-23 Item No.33.36, Sr. No. 1023, Page No. 216, Bd M35 B, Page No. 393. FIRST FLOOR

Providing and fixing machine cut mirror polished 18mm to 20mm thick Telephone black granite / Amba white / Cat bary brown / RBI red / Ocean brown Granite Stone Partitions with full moulding the edges etc. complete. Both side polish. SSR 2022-23 Item No.33.36, Sr. No. 1023, Page No. 216, Page No. 393. SECOND FLOOR

Providing and laying Vitrified mirror / Glossy finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Dado and Skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.41, Sr.No. 1028, Page No.217, Bd. M-12 page Number 385. GROUND FLOOR

Providing and laying Vitrified mirror / Glossy finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Dado and Skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.41, Sr.No. 1028, Page No.217, Bd. M-12 page Number 385. FIRST FLOOR

Providing and laying Vitrified mirror / Glossy finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Dado and Skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.41, Sr.No. 1028, Page No.217, Bd. M-12 page Number 385. SECOND FLOOR

Providing and laying Vitrified Matt finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.42, Sr.No. 1029, Page No.217, Bd. M-12 page Number 385. GROUND FLOOR

Providing and laying Vitrified Matt finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.42, Sr.No. 1029, Page No.217, Bd. M-12 page Number 385. FIRST FLOOR

Providing and laying Vitrified Matt finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.42, Sr.No. 1029, Page No.217,, Bd. M-12 page Number 385. SECOND FLOOR

Providing and laying Vitrified Matt finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Dado and Skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.43, Sr.No. 1030, Page No.217, Bd. M-12 page Number 385. GROUND FLOOR

Providing and laying Vitrified Rustic Matt Stone finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.44, Sr.No. 1031, Page No.217, Bd. M-12 page Number 385. GROUND FLOOR

Providing and laying Vitrified Rustic Matt Stone finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.44, Sr.No. 1031, Page No.217, Bd. M-12 page Number 385. FIRST FLOOR

Providing and laying Vitrified Rustic Matt Stone finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.44, Sr.No. 1031, Page No.217, Bd. M-12 page Number 385. SECOND FLOOR

Providing and laying Vitrified Rustic Matt Stone finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Dado and Skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.45, Sr.No. 1032, Page No.218, Bd. M-12 page Number 385. GROUND FLOOR

Providing and laying Vitrified Rustic Matt Stone finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Dado and Skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.45, Sr.No. 1032, Page No.218, Bd. M-12 page Number 385. FIRST FLOOR

Providing and laying Vitrified Rustic Matt Stone finish tiles having size 590mm to 605mm x 590mm to 605mm of 8 to 10mm thickness and confirming to IS 15622- 2006 (Group Bla) of approved make shade and pattern for Dado and Skirting in required position fixed in 1:4 cement mortar including neat cement float, filling joints, curing and cleaning etc .complete. SSR 2022-23, Item No. 33.45, Sr.No. 1032, Page No.218, Bd. M-12 page Number 385. SECOND FLOOR

Providing Leather Finished Polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. SSR 2022-23, Item No. 33.56, Sr. No. 1043, Page No. 219, As directed by Engineer-In-Charge. GROUND FLOOR

Providing Leather Finished Polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matt finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete. SSR 2022-23, Item No. 33.56, Sr. No. 1043, Page No. 219, As directed by Engineer-In-Charge. FIRST FLOOR

Providing and laying Telephone black / Amba white / Cadbury brown / Ruby red / Ocean brown Granite Stone of 18mm to 20mm thickness for Door Frame / Dado / Window boxing etc. on CM 1:6 including filling joints with polymer base filler nosing / moulding the sharp edges wherever necessary, curing etc. complete. SSR 202-23, Item No. 33.68, Sr. No. 1052, Page No. 220, As directed by Engineer-In-Charge. GROUND FLOOR

Providing and laying Telephone black / Amba white / Cadbury brown / Ruby red / Ocean brown Granite Stone of 18mm to 20mm thickness for Door Frame / Dado / Window boxing etc. on CM 1:6 including filling joints with polymer base filler nosing / moulding the sharp edges wherever necessary, curing etc. complete. SSR 202-23, Item No. 33.68, Sr. No. 1052, Page No. 220, As directed by Engineer-In-Charge. FIRST FLOOR

Providing and fixing in position, heavy duty 100 % polypropylene Carpet on Auditorium Floor with 3 mm underlay, 980 gsm, 4 mtr width, fire retardant, plain backing, needle punch technology, stain proof as per Architectural & Acoustical design, instructions and complete in all aspects. As directed by Engineer-In-Charge.

Providing and fixing soft compacted basalt stone of size 300mm x 450mm x 150mm thick for Paving/Flooring with dressing as per drawing and as directed by Engineer-In-charge. The stones to be finely flat, chisel dressed on the surface, without windings, and the joints running true and parallel from side to side. The stones to be laid with joints not exceeding 3mm thick and and to be evenly and firmly bedded flush in mortar on the existing concrete, and no hollows left. Courses to be parallel and at reight angles to the wall, and the stone shall be laid with break joint at least 150mm or as directed by Engineer-In-Charge, including cement mortar bed of 20mm thickess in cement mortar 1:4 with filling joints, curing, cleaning, etc. complete. etc. complete. As directed by Engineer-In-Charge. (The sample of the moulded Paving stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing and Laying Polished hand cut White Marble (Rajnagar Plain or equivalent, good quality other than Makrana, with Telephone Black Granite diamod cut inlay Flooring as directed and approved from Engineer-In-Charge and Consultant) Flooring 18mm thick and 45cm to 55cm wide in Plain / Diamond pattern of size 45cm x 45cm with inlay of 50mm x 50mm of Telephone Black Granite, including cutting, fixing, filing joints with neat cement slurry, curing, Mirror Polishing and cleaning etc. complete as directed by the Engineer-In-Charge and Consultant.

Providing and fixing Rolling Shutter fabricated from steel laths of minimum thickness 0.9 mm with lock plate of 3.15 mm thickness reinforced with 35 x 35 x 5 mm angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm and 3.15 mm respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm minimum size and shape with square bar, suspension shaft of minimum 32 mm diameter, hood cover of M.S. sheet not less than 0.9 mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 62481979) (With mechanical gear) SSR 2022-23, Item No. 39.25, Sr. No. 1218, Page No. 249, Bd.T-55, Page No. 510.

Providing and fixing in position powder coated Aluminium Louvered Windows / Ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. SSR 2022-23, Item No. 39.68, Sr. No. 1263, Page No.259, As directed by Engineer-In-Charge. GROUND FLOOR

Providing and fixing in position powder coated Aluminium Louvered Windows / Ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. SSR 2022-23, Item No. 39.68, Sr. No. 1263, Page No.259, As directed by Engineer-In-Charge. FIRST FLOOR

Providing and fixing in position powder coated Aluminium Louvered Windows / Ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 mm x 1.22 mm box type, 5 mm thick sheet glass louvers, of approved quality etc. complete. SSR 2022-23, Item No. 39.68, Sr. No. 1263, Page No.259, As directed by Engineer-In-Charge. SECOND FLOOR

Sliding Window- 3 Track (2 Glass shutter + 1 flymesh) of approved make with DGU, providing and fixing of Sliding Window- 3 Track (2 Glass shutter + 1 flymesh ). For details refer to Specifications. As directed by Engineer in charge. SSR - 2022-23, Item No. 48.23, Sr.No. 1641, Page No.314, As directed by Engineer-In-Charge.

Providing & fixing of Casement Fixed Window of approved make with DGU. The extruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material V2 / V4 as directed by Engineer in charge. SSR- 2022-23, Item No. 48.24, Sr. No. 1642, Page No.314, As directed by Engineer-In-Charge.

Providing and fixing of Metal Door, door frame shall be single rebate profile of size 125mm x 57mm made out of 1.6mm (16gauge) mimimum thick galvanised steel sheet, Frames shall be mitre joints and Double leaf door shall be 46.6mm thick fully flush with infill of resin bonded honeycomb kraft, door leaf shall be of 1.2mm (18 gauge) minimum thick galvanized steel sheet with provision for louvers inbuilt as per drawing / with vision panel to be provided with 6mm glass, beeding and screws from inside. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening.All doors shall be factory prepared for receiving appropriate hardwares and provided with necessary reinforcement for hinges, locks, handle and door closure, colour of door frame and shutter shall be of approved colour, etc complete. As directed by Engineer-In-Charge.

Providing and fixing of metal door,door frame shall be single rebate profile of size 125mm X 57mm made out of 1.6mm(16gauge) mimimum thick galvanised steel sheet,frames shall be mitre joints and Single leaf door shall be 46.6mm thick fully flush with infill of resin bonded honeycomb kraft,door leaf shall be of 1.2mm (18 gauge)minimum thick galvanized steel sheet with provision for louvers inbuilt as per drawing / with vision panel to be provided with 6mm glass, beeding and screws from inside. Frames should be provided with back plate bracket and anchor fasteners for installation on a finished plastered masonry wall opening .All doors shall be factory prepared for receiving appropriate hardwares and provided with necessary reinforcement for hinges,locks,handle and door closure,colour of door frame and shutter shall be of approved colour, etc complete. As directed by Engineer-In-Charge.

Providing & Fixing in position Acoustical Door along with Frame of 150mm X 100mm, Shutters shall be made from Teak wood frame for door leaf of 125 mm X 100 mm section, at 600 x 600 C/C, filled with 50 mm thick and 48 kg/sqm density of Glasswool, 18 mm waterproof ply from both side, finished with approved Veneer of 3mm, from inside and outside, including 150 mm heavy duty SS hinges 4 no each shutter, including cost of required Cut-Outs, melamine polish from both side of the door with necessary Scaffolding, etc. Doors shall have handles of approved design of size 450mm length, Tower bolts & Locking arrangements as directed. as per Architectural and Acoustical Design and Instructions and Complete. As directed by Engineer-In-Charge.

Providing and Fixing Burma Teak Wood Frame with / without ventilator of size as specified for Doors and Windows including chamfering, rounding, rebating, iron holdfast of size 300mm x 40mm x 5mm including one coat of primer and two coats of oil paint for wood, As directed by Engineer-In-Charge etc. complete.

Providing and Fixing new 40mm thick Burma Teak Wood Glazed Window Shutters with 1/2" beading trellies design on the 5mm glass panes with panels 40mm thick with / without ventilator, including, fixtures, fastenings and finishing the wood work with 2 coats of primer and melamine polish, all necesary fittings to be fixed at the location, all inclusive as directed by Engineer-In-Charge etc. complete.

Providing and Fixing Burma Teak Wood Solid 40mm thick Fully Panelled Door Shutter without frames in Single or Double leaf 40mm thick panel as per detailed drawings with wrought iron hold fast, brass fixtures and fastenings and handles on both sides and finishing with two coats of primer and melamine polish, all the necessary fitings to be fixed at the specified location, all inclusive as directed by Engineer-In-Charge etc. complete.

Item Code-DFD2-Providing and fixing steel frame for door of size 3.35m wide x 6.74m ht two leaf openable Door fabricated and made out of MS steel box section of rectangular hollow section (RHS) of size 200mm x 4.00mm thk. For main door shutter frame work as per drawing with MS Box section of square of hollow section (SHS) of size 100mm x 4mm thk for cross Member of shutter frame with top and bottom heavy duty pivot hinges welded to main door shutter frame as per Drawing and door shutter cladded with Burma Teakwood planks of size 200mm x 25mm thick placing in vertical direction from top to bottom and placing side by side from both side of shutter and with 25mm teakwood plank on all remaining edges of the bot shutters and separate Burma Teakwood Members of size 250mm x 75mm fixing on front side of each shutter as per detail elevation Drawing including same size cureved member as per elevation matching with stone arch of civil construction and fixing decorative iron door nobs as per design on the elevation frame ae well as the door shutter central top portion of smaller size door nobs and spikes fixed on MS steel plate fixed to main door shutter of size 150mm wide x 5mm thick horizontally only on front side of both door shutters. Fabrication of main shutter frame is to be fabricated with RHS profile cutting and right angle joint to be fabricated with 45° angle cutting and welding all members without any opening exposing inner surface of box Member. Including melamine polishing all wooden surfaces. Item including all materials, labour, transportation, scaffolding, Erection, with all necessary tools with all leads and lifts etc. Complete.

Providing and fixing Mild Steel Grill Railing 20 Kilogram/sq.m with teak wood hand rail of size 75mm x 60 mm.and sill of 75mm.x 25 mm.and newel posts for staircases, including fabricating, fix-tures, erecting, painting the grill work with one coat of anti-corrosive paint and two coats of oil painting with approved colour and polishing the sill, hand rail and the newel post with french polish. SSR 2022-23, Item No. 40.03, Sr. No. 1293, Page No. 264, Bd.U 1, Page No. 537.

Providing and Fixing Railing of Cast Iron Balustrade (0.30m wide x 0.80m in height) using wooden handrails as per drawing and design suitable to the Historic Structure, using atleast 10kg per Balustrade with First Sort Burma Teak Wood Hand Rails to be carved in minimum 80mm x 80mm section to be fixed at the location using necessary joinery, inclusive of French Polish application to wooden hand rails, etc. all complete. As directed by Engineer-In-Charge.

Providing and applying two coats of Exterior Weather Shield paint of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface ,applying primer coat,scaffolding if necessary, and watering the surface for two days etc complete.(With prior approval of S.E.) SSR - 2022-23, Item No. 35.26, Sr.No.1095,Page No.225,BDO As directed by Engineer Incharge

Providing and applying 2 coats of 100% Pure Acrylic low VOC and APEO & HCHO free water based Paint of approved colour that belongs to class 1 flame spread resistance of approved make Paint should provide durable and long lasting silk finish with a high crack tolerance of upto 1mm. Paint should have an oustanding washability with high resistance to wide range of bacteria and fungus. Paint has to be applied on smooth and uniform surface prepared by an acrylic copolymer low VOC & Odour putty. This surface should be primed with water based low VOC Primer. The work activity should cover all aspects of applying paints from surface preparation as directed by Engineer in charge. SSR-2022-23, Item No. 48.11, Sr. No. 1630, Page No. 311, As directed by Engineer-In-Charge.

Providing and applying two coats of High Albedo Paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc, washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- incharge. SSR - 2022-23, Item No. 48.19, Sr. No. 1637, Page No. 313, As directed by Engineer-In-Charge.

Providing and applying two coats of textured synthetic paint of approved shade and quality and one coat of primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil, grease, dirt and other materials as required, etc. complete. SSR 2022-23, Item No. 35.24, Sr. No. 1093, Page No.225, As directyed by Engineer-In-Charge.

Providing Ashlar Masonry for Ground Level Moulding with Soft Compacted Basalt stone of size 600mm x 300mm x 200mm from approved source, with dressing as per drawing and as directed by Engineer-In-Charge, in Cement Mortar 1:4 with paper fitting joints, including transportation and conveyance to specific required location, scaffolding, tools and tackles, racking the joints with neat cement slurry, curing, cleaning, etc. complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing Ashlar Masonry for Mural Moulding with Soft Compacted Basalt stone of size 300mm x 300mm x 350mm from approved source, with dressing as per drawing and as directed by Engineer-In-Charge in Cement Mortar 1:4 with paper fitting joints, including transportation and conveyance to specific required location, scaffolding, tools and tackles, racking the joints with neat cement slurry, curing, cleaning, etc. complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing Ashlar Masonry for Mahirap Rectangular Moulding with Soft Compacted Basalt stone of size 300mm x 300mm x 300mm from approved source, with dressing as per drawing and as directed by Engineer-In-Charge in Cement Mortar 1:4 with paper fitting joints, including transportation and conveyance to specific required location, scaffolding, tools and tackles, racking the joints with neat cement slurry, curing, cleaning, etc. complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing Ashlar Masonry for Mahirap Arch Moulding with Soft Compacted Basalt stone of size 300mm x 300mm x 300mm from approved source, with dressing as per drawing and as directed by Engineer-In-Charge in Cement Mortar 1:4 with paper fitting joints, including transportation and conveyance to specific required location, scaffolding, tools and tackles, racking the joints with neat cement slurry, curing, cleaning, etc. complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing Ashlar Masonry for Plinth Level Moulding with Soft Compacted Basalt stone of size 300mm x 250mm x 150mm from approved source, with dressing as per drawing and as directed by Engineer-In-Charge in Cement Mortar 1:4 with paper fitting joints, including transportation and conveyance to specific required location, scaffolding, tools and tackles, racking the joints with neat cement slurry, curing, cleaning, etc. complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing Ashlar Masonry for Moulding at 9.15m level with Soft Compacted Basalt stone of size 300mm x 300mm x 150mm from approved source, with dressing as per drawing and as directed by Engineer-In-Charge in Cement Mortar 1:4 with paper fitting joints, including transportation and conveyance to specific required location, scaffolding, tools and tackles, racking the joints with neat cement slurry, curing, cleaning, etc. complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing Ashlar Masonry for Moulding at 13.50m level with Soft Compacted Basalt stone of size 300mm x 300mm x 150mm from approved source, with dressing as per drawing and as directed by Engineer-In-Charge in Cement Mortar 1:4 with paper fitting joints, including transportation and conveyance to specific required location, scaffolding, tools and tackles, racking the joints with neat cement slurry, curing, cleaning, etc. complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing and fixing soft compacted basalt stone of size 600L x470 D x 300 Hmm size from approved sourcw, for Carved Flower design (750mm x 750mm) at 6.85 m level embeded in Ashlar masonry, with dressing as directed by engineer in charge in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools tackels racking the joints with neat cement slurry, curing cleaning varnishing etc complete. (The sample of the Mural stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) As directed by Engineer-In-Charge.

Providing and fixing soft compacted basalt Nevasa / Baramati type stone of size 600L x470 D x 300 Hmm size from approved source, for Carved Horse and Elephant Mural design (770mm x 880mm) at 8.35 m level embeded in CR masonry, with dressing as directed by engineer in charge in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools tackels racking the joints with neat cement slurry, curing cleaning varnishing etc complete. (The sample of the Mural stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)As directed by Engineer-In-Charge.

Providing Ashlar Masonry for 2.50m Level Moulding with Soft Compacted Basalt stone of size 300mm x 250mm x 150mm from approved source, with dressing as per drawing and as directed by Engineer-In-Charge in Cement Mortar 1:4 with paper fitting joints, including transportation and conveyance to specific required location, scaffolding, tools and tackles, racking the joints with neat cement slurry, curing, cleaning, etc. complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.)

Providing Ashlar Masonry for Stone Moulding at 150mm.Ht. with Soft Compacted Basalt stone. Stone Size - 300mm(W)x150mm (Ht.)x450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools tackels racking the joints with neat cement slurry, curing cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.19-RM Item Code-SM1

Providing Ashlar Masonry for Plinth Level Stone Molding at 750mm.Ht. with Soft Compacted Basalt stone. Stone Size - 300mm(W)x150mm (Ht.)x450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.19-RM Item Code-SM2

Providing Ashlar Masonry for Talkhada at 1100mm.Ht. with Soft Compacted Basalt stone. Stone Size - 650mm(W)x650mm (L)x350mm (Ht.) with dressing as per drawing and as directed by Engineer-In-Charge in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.19-RM Item Code-STK1

Providing Ashlar Masonry for Stone Moulding at 235mm. Ht. with Soft Compacted Basalt stone. Stone Size - 330mm(W)x235mm (Ht.)x450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.20-HSB. Item Code-SM3

Providing Ashlar Masonry for Plinth Level Stone Moulding at 900mm. Ht. with Soft Compacted Basalt stone. Stone Size - 300mm(W)x200mm (Ht.)x450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.20-HSB. Item Code-SM4

Providing Ashlar Masonry for Stone Steps with Soft Compacted Basalt stone. - One step of minimum 550mm Wide x 1.50meter long x 150mm thk. made out of 300mm Long stones 5 Nos. Finished Stone Sise 550mm x 1500mm x 150mm with dressing as per drawing and as directed by Engineer-In-Charge in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) Item Code-SST1

Providing Ashlar Masonry for Stone Steps with Soft Compacted Basalt stone. - One step of minimum 600mm wide x 3.00meter long x 150mm thk. made out of 300 mm Long stones 10 Nos. Stone Size - 300mm. long 150mm(Ht.) x 600mm wide stone. with dressing as per drawing and as directed by Engineer-In-Charge in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB-PVB. Item Code-SST3

Providing Ashlar Masonry for Stone Moulding at 322mm.Ht. with Soft Compacted Basalt stone. Stone Size - 200mm(W) x 200mm (Ht.)x450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM6

Providing Ashlar Masonry for Stone Moulding at 879mm.Ht. with Soft Compacted Basalt stone. Stone Size- 150mm(W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM7

Providing Ashlar Masonry for Stone Moulding at 1.109m.Ht. with Soft Compacted Basalt stone. Stone Size - 200mm(W) x 230mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.29+30-ADB+PVB. Item Code-SM8

Providing Ashlar Masonry for Stone Moulding at 1.715m.Ht. with Soft Compacted Basalt stone. Stone Size- 150mm(W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM9

Providing Ashlar Masonry for Stone Moulding at 2.077meter.Ht. with Soft Compacted Basalt stone. Stone Size- 200mm(W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM10

Providing Ashlar Masonry for Stone Moulding at 2.739meter.Ht. with Soft Compacted Basalt stone. Stone Size- 150mm(W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM11

Providing Ashlar Masonry for Stone Moulding at 2.969meter.Ht. with Soft Compacted Basalt stone. Stone Size- 250mm(W) x 200mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM12

Providing Ashlar Masonry for Stone Moulding at 3.217meter.Ht. with Soft Compacted Basalt stone. Stone Size- 200mm(W) x 250mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM13

Providing Ashlar Masonry for Stone Moulding at 3.988meter.Ht. with Soft Compacted Basalt stone. Stone Size- 200mm(W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM14

Providing Ashlar Masonry for Stone Moulding at 4.247meter.Ht. with Soft Compacted Basalt stone. Stone Size- 200mm(W) x 300mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM15

Providing Ashlar Masonry for Stone Moulding at 4.543meter.Ht. with Soft Compacted Basalt stone. Stone Size- 300mm(W) x 300mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM16

Providing Ashlar Masonry for Stone Moulding at 4.791meter.Ht. with Soft Compacted Basalt stone. Stone Size- 200mm(W)x250mm (Ht.)x450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB Item Code-SM17

Providing Ashlar Masonry for Stone Moulding at 4.543meter.Ht. with Soft Compacted Basalt stone. Stone Size- 212mm(W) x 555mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM18

Providing Ashlar Masonry for Mural Molding at 4.522meter.Ht. with Soft Compacted Basalt stone. Size- 3357mm(W) x 4522mm (Ht.) x 450mm (L) Stone size - 200mm x 330mm x 450mm with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM19

Providing Ashlar Masonry for Mahirap Arch Molding at 7.721meter. with Soft Compacted Basalt stone. Arch Size- 5344mm(W) x 2930mm (Ht.) x 300mm (L) Stone size 300mm x 300mm x 450mm, with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-MARM1

Providing Ashlar Masonry for Parapet Charya at 9.492meter.Ht. with Soft Compacted Basalt stone. Size- 690mm(W)x1056mm (Ht.)x450mm thk. made out of 350mm x 350mm x 450mm 6 stones, with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-PC1

Providing Ashlar Masonry for Parapet Corner Charya at 9.492meter. Ht. with Soft Compacted Basalt stone.Stone Size- 690mm(W) x 1056mm (Ht.) x 450mm thk. made out of 350mm x 350mm x 450mm 6 stones, with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-PCC1

Providing Ashlar Masonry for Parapet Charya at 10.674 meter. Ht. with Soft Compacted Basalt stone. Stone Size- 690mm(W) x 1056mm (Ht.) x 450mm thk. made out of 350mm x 350mm x 450mm 6 stones, with dressing as per drawing andas directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-PC2

Providing Ashlar Masonry for Parapet Corner Charya at 10.674meter. Ht. with Soft Compacted Basalt stone. Stone Size- 690mm(W) x 1052mm (Ht.) x 450mm thk. made out of 350mm x 350mm x 450mm 6 stones, with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-PCC2

Providing Ashlar Masonry for Mahirap Arch Molding at 4.067meter. Ht. with Soft Compacted type stone. Size- 2267mm(W) x 1667mm (Ht.) x 300mm (L) stone size 300mm x 300mm x 450mm, with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB Item Code-MARM2

Providing Ashlar Masonry for Stone Moulding at 8.436meter. Ht. with Soft Compacted Basalt stone. Stone Size- 150mm(W) x 350mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, and racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 29+30-ADB+PVB. Item Code-SM20

Providing Ashlar Masonry for Stone Moulding for Corner Piece at 450mm. Ht. with Soft Compacted Basalt stone. Stone Size- made out of 310mm Wide x 245mm(Ht.) x 450mm Long stone. with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 37-PMB. Item Code-SM6C

Providing Ashlar Masonry for Plinth Level Stone Moulding at 1.25meter. Ht. with Soft Compacted Basalt stone. Stone Size- 300mm (w) 250mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 40-RBP. Item Code-SM17

Providing Ashlar Masonry for Plinth Level Stone Moulding at 1.20meter. Ht. with Soft Compacted Basalt stone.Stone Size-160mm (W) x 100mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 41-SSB. Item Code-SM18

Providing Ashlar Msonry for Stone Moulding at 3.40meter Ht. with Soft Compacted Basalt stone. Stone Size-200mm (W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 41-SSB. Item Code-SM19

Providing Ashlar Masonry for Stone Moulding at 5.60meter.Ht. with Soft Compacted Basalt stone. Stone Size-200mm (W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 41-SSB. Item Code-SM20

Providing Ashlar Masonry for Stone Moulding at 6.70meter. Ht. with Soft Compacted Basalt stone. Stone Size-200mm (W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing andas directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 41-SSB. Item Code-SM21

Providing Ashlar Masonry for Stone Moulding at 9.20meter. Ht. with Soft Compacted Basalt stone. Stone Size-200mm (W) x 150mm (Ht.) x 450mm (L) with dressingas per drawing and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 41-SSB. Item Code-SM22

Providing Ashlar Masonry for Stone Moulding at 10.30meter. Ht. with Soft Compacted Basalt stone. Stone Size-200mm (W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 41-SSB. Item Code-SM23

Providing Ashlar Masonry for Stone Moulding at 13.70meter. Ht. with Soft Compacted Basalt stone. Stone Size-200mm (W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 41-SSB. Item Code-SM24

Providing Ashlar Masonry for Stone Moulding at 17.70meter. Ht. with Soft Compacted Basalt stone. Size-200mm (W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints ( paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 41-SSB. Item Code-SM25

Providing Ashlar Masonry for Stone Cladding with Soft Compacted Basalt stone. 30mm thk. stone size - 200mm x 300mm x 30mm. for All Wall with dressing as per drawing, andas directed by Engineer-In-Charge, in cement mortar 1:4, including Adhesive, with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) Item Code-SC1 For Building No. 41-SSB

Providing Ashlar Masonry for Stone Steps with Soft Compacted Basalt stone. - One step of minimum 600mm Wide x 300mm (L) x 150mm Ht. made out of 300mm Long stones. with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) Item Code-SST5 For Building No. 44-DVT

Providing Ashlar Masonry for Stone Moulding at 0.15meter. Ht. with Soft Compacted Basalt Nevasa/Baramati type stone. Stone Size- 300mm(W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 50-AD. Item Code-SM26

Providing Ashlar Masonry for Plinth Level Stone Moulding at 0.75meter. Ht. with Soft Compacted Basalt stone. Stone Size- 300mm(W) x 150mm (Ht.) x 450mm (L) with dressing as per drawing,and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 50-ADK. Item Code-SM27

Providing Ashlar Masonry for Stone Moulding at 11.40 meter. Ht. with Soft Compacted Basalt stone. Size- 200mm(W) x 200mm (Ht.) x 450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 43-FOF. Item Code-SM34

Providing Ashlar Masonry for Mahirap Arch Moulding at 4.22meter. Ht. with Soft Compacted Basalt stone. Size- 200mm Ht.x200mm x 450mm with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 52-SPDR. Item Code-MARM3

Providing Ashlar Masonry for Stone Moulding at 0.245 meter. Ht. with Soft Compacted Basalt stone. Inculding design as shown in Architectural Drawing. Size- 425mm(W)x245mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 61-SMS. Item Code-SM49

Providing Ashlar Masonry for Stone Moulding at 0.970 meter. Ht. with Soft Compacted Basalt stone. Inculding design as shown in Architectural Drawing. Size- 425mm(W)x245mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-SM50

Providing Ashlar Masonry for Stone Moulding at 1.365 meter. Ht. with Soft Compacted Basalt stone. Size- 320mm(W)x145mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-SM51

Providing Ashlar Masonry for Stone Moulding at 1.725 meter. Ht. with Soft Compacted Basalt stone. Leaser Cut Size- 320mm(W)x360mm (Ht.)x 450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-LSM1

Providing Ashlar Masonry for Stone Moulding at 1.85 meter. Ht. with Soft Compacted Basalt stone. Size- 320mm(W)x125mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-SM52

Providing Ashlar Masonry for Stone Moulding at 0.395 meter. Ht. with Soft Compacted Basalt stone. Size- 230mm(W)x145mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-SM53

Providing Ashlar Masonry for Stone Moulding at 0.880 meter. Ht. with Soft Compacted Basalt stone. Size- 230mm(W)x125mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-SM54

Providing Ashlar Masonry for Stone Moulding at 0.880 meter. Ht. with Soft Compacted Basalt stone. Size- 425mm(W)x120mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-SM54

Providing Ashlar Masonry for Stone Moulding at 1.235 meter. Ht. withSoft Compacted Basalt stone. Size- 310mm(W)x200mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS Item Code-SM54

Providing Ashlar Masonry for Stone Moulding at 3.535 meter. Ht. with Soft Compacted Basalt stone. Size- 300mm(W)x250mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-SM55

Providing Ashlar Masonry for Stone Moulding at 3.535 meter.Ht. and Fixing Soft Compacted Basalt stone. Size- 300mm(W)x250mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No.61-SMS. Item Code-SM56

Providing Ashlar Masonry for Stone Moulding at 3.785 meter. Ht. with Soft Compacted Basalt stone. Size- 1450mm(W)x150mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 61-SMS Item Code-SM57

Providing Ashlar Masonry for Stone Moulding at 3.985 meter. Ht. with Soft Compacted Basalt stone. Size- 45mm(W)x170mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 61-SMS. Item Code-SM58

Providing Ashlar Masonry for Stone Moulding at 0.73 meter. Ht. with Soft Compacted Basalt stone. Size- 100mm(W)x170mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 66-BOH. Item Code-SM59

Providing Ashlar Masonry for Stone Moulding at 0.90 meter. Ht. with Soft Compacted Basalt stone. I Size- 100mm(W)x170mm (Ht.)x450mm (L) with dressing as per drawing, and as directed by Engineer-In-Charge, in cement mortar 1:4 with fitting joints (paper) including transportation and conveyance to specific required location, scaffolding, tools and tackels, racking the joints with neat cement slurry, curing, cleaning etc complete. The stones shall be dressed full or to template, or as shown in working drawings. The exposed faces of the stone shall be fine - chissel dressed, and all joints shall be in line and close not more than 3mm thick. All visible angles and edges to be free from unsightly chippings, etc. complete. As directed by Engineer-In-Charge. (The sample of the moulding stone shall be approved prior to execution by Consultant/Engineer-In-Charge.) For Building No. 66-BOH tem Code-SM60

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC column (wada) Top Bracket TYPE A (front) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 300mm x 300mm x 80mm

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC column (wada) top bracket TYPE B (side) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 300mm x 300mm x 80mm

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC wada window (including frame + arch + bottom baluster) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension 1.15m x 2.55m x 0.15m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC wada window half thk frame for blank wall cladding type Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 1.15m x 2.55m x 0.11m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC column face cladding (CC-1) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 300mm x 25mm

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC column base (Talkhada) at base cladding Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 0.35m x 0.6m x 0.15m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC window arch with top arch and bottom baluster (window finished from both sides) (WAR 1) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 2.40m x 3.45m x 0.08m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC window arch with top arch and bottom baluster (for blank wall cladding) (WAR 2) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 2.40m x 3.45m x 0.04m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC window arch with top arch and bottom baluster (for blank wall cladding) (WAR 3) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 5.40m x 3.45m x 0.04m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC window arch with only arch (WAR 3) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge.Dimension - 2.40m x 9.75m x 0.04m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC jali (WJ) (height as per drawing) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 2.40m x 0.05m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC main entrance arch (MEAR 1) (incl. MS frame structure with epoxy primer and PU paint finished in two coats with both side. Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 11.40m x 6.65m x 0.15m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC motif (NKM 1) (length as per dwg) Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. Dimension - 0.62m x 0.03m

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, Beam top cornice in GFRC Specifications : GFRC- Compressive strength - 80 MPA, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA , Wherever required GFRC with stud frame and flex anchors to be adopted for cornices or similar components. Mild steel if used should be passivated and with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge.

PRECAST CONCRETE / GFRC Designing, Manufacturing as per drawing, Supplying and Installing in position, Precast concrete bracket (NKB 1) with stone finish on surface cladding (precast concrete manufactured as per given option below and rate shall be same for all options) Specifications : Precast concrete with compressive strength 80 MPA and HDG exposed fixing cleats and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in GFRC / Precast concrete should be SS 316 plated. Dimension - 1.60m x 0.976m x 0.18m

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Parapet Stone (Charya)- (CH1) Size- 0.371w X 0.403ht X 150mm thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in Clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Braket (GBR1) Size- 0.571w X 0.493ht X 120mm thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Corner Braket (GBR1) Size- 0.571w X 0.493ht X 120mm thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Braket (BR2) Size- 0.903w X 0.750ht X 200mm thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Window Arch (GWAR11) Size- 0.60w X 0.17ht X 40mm Thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Window Arch (GWAR20) Size- 0.450w X 0.598ht X 40mm Thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Window Arch (GWAR21) Size- 0.450w X 0.598ht X 40mm Thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Moulding (GMOL1) Size- 0.350w X 0.10ht Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 15- SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Moulding (GMOL2) Size- 260mm w X 50mm ht Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 15- SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Moulding (GMOL3) Size- 8.550w X 0.15ht Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 15- SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Moulding (GMOL1A) Size- 0.80w X 295mm ht Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Window Arch (GWAR7) Size- 0.60w X 1.50ht Finishing- with stone texture on surface, including integral pigmentation including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 15- SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC PILLAR ( GPLR1) Size- 200mm w. X 2.113ht x 0.040m thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.15 SJS

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Talkhada (TK2) Size- 0.75L X 0.260w X 0.35ht Finishing- Stone Finish (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in Clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.18-RPNB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Flower Design (GFD) Size- 0.30w X 0.36ht. x 0.040m thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No.18-RPNB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Moulding (GMOL3) Size- 300mm w X 300mm ht. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No.18-RPNB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Small Window (GGW) Size- 400mm wide X 400mm ht. x 40mm thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No.18-RPNB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Baluster (GBAL1) Size- 2.201w X 0.90ht X 80mm Thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No.19-RM

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Braket (GBR4) Size- 0.352w X 0.30ht. X 80mm Thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No.19-RM

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Braket (GBR5) Size- 0.35w X 0.40ht. X 80mm Thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No.19-RM

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Window Arch (GWAR12) Size- 1.10w X 1.71ht X 100 Thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 19- RM

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC KALASH (GKAL) Size- 4.14w X 3.145ht - 2 Nos. + 4.56L X 3.145 ht - 2 Nos. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 19- RM

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Panel (PCP1) Size- 0.53m w X 3.00m ht. x 0.075m thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.20 HSB

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Colum Capital (CCC1) Size- 0.77m w X 0.30m ht. x 0.075m thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.20 HSB

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Parapet Charya (CH2) Size- 0.80m w X 0.75m ht X 150mm thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in Clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No. 23 PLJVB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Arch (GAR1) Size- 3.59m w X 3.90m ht X 60mm Thk. Finishing- with stone texture on surface, including integral pigmentation including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 23 PLJVB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Arch (GAR2) Size- 4.21m w X 4.80m ht x 0.040m thk. Finishing- with stone texture on surface, including integral pigmentation including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 23 PLJVB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Wall Panel (GWP1) Size- 0.30m w X 3.15m ht x 0.040m thk. Finishing- with stone texture on surface, including integral pigmentation including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 23 PLJVB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Wall Panel (GWP2) Size- 0.72m w X 3.15m ht x 0.040m thk. Finishing- with stone texture on surface, including integral pigmentation including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 23 PLJVB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Wall Panel (GWP3) Size- 30mm Thk. Finishing- with stone texture on surface, including integral pigmentation including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 23 PLJVB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Moulding (GMOL4) Size- 100mm ht x 300mm wide Finishing- with stone texture on surface, including integral pigmentation Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 23 PLJVB

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Braket (BR6) Size- 0.2w X 0.3ht X 100mm thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.23 PLJVB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Arch with Panel (GAR5) Size- 2.10m w X 3.00m ht x 0.080m thk. Finishing- with stone texture on surface, including integral pigmentation including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 29+30- PLJ + ADB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Arch (GAR6) Size- 4.15m w X 0.915m ht x 0.080m thk. Finishing- with stone texture on surface, including integral pigmentation including making mould from Natural stone or any other surfaces as desire for further producation. Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 29+30- PLJ + ADB

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Arch - (CAR1) Size- 0.50m w X 0.75m ht x 0.10m thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in Clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.29+30 PLJ = ADB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Window Arch with Baluster (GWAR3) Size- 2.80m w X 3.20m ht x 0.040m thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 41 SSB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Window Arch (GWAR4) Size- 2.80m w X 2.40m ht x 0.040m thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 41 SSB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Window Arch (GWAR5) Size- 2.00m w X 1.60m ht x 0.080m thk. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 41 SSB

Designing, Manufacturing as per drawing, Supplying and Installing in position, GFRC Molding (GMOL-) Size- 160mm w X 100mm ht. Finishing- Smooth texture on surface including painting with Jotun Tex ultra or equivalent elastomeric flexible paint Specifications : GFRC- Compressive strength - M- 80 Grade, Flexural strength (MOR) - 18 MPA, Flexural LOP - 8 MPA, Wherever required GFRC with stud frame and flex anchors to be adopted as per required. Mild steel if used should be passivated and painted with a epoxy primer and PU coating. Exposed steel brackets/cleats/hardware should be hot dip galvanized (HDG). Fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent. The price shall include preparation of shop drawings, manufacturing, transport, unloading and installation completed in all respects including scaffolding upto 3 storeys or 12 m height if required. As directed by Engineer-In-Charge. For Building No. 41 SSB

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Parapet Stone (Charya)- (SCH1) Size- 0.60m w X 0.90m ht X 0.250m ht. Finishing- with stone texture on surface, including integral pigmentationn. Including making mould from Natural stone or any other surfaces as desire for further producation. (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No. 43 FOF

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Parapet Corner Stone (Charya)- (SCH2) Size- 0.60m w X 0.90m ht X 0.25m Finishing- with stone texture on surface, including integral pigmentation Including making mould from Natural stone or any other surfaces as desire for further producation. (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No. 43 FOF

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Arch (CWAR16) Size- 2.40m w X 3.45m ht x 0.080m thk. Finishing- with stone texture on surface, including integral pigmentation Including making mould from Natural stone or any other surfaces as desire for further producation. (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.43 FOF

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Arch (CWAR17) Size- 2.20m w X 3.90m ht x 0.080m thk. Finishing- with stone texture on surface, including integral pigmentation. Including making mould from Natural stone or any other surfaces as desire for further producation. (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.43 FOF

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Stone Arch (SCH3) Size- 0.85m w X 0.90m ht X 0.450m thk. Finishing- with stone texture on surface, including integral pigmentation. Including making mould from Natural stone or any other surfaces as desire for further producation. (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.43 FOF

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Panel (CPC5) Size- 30mm Thk. with stone masonry finish of maximum panel size 1200mm Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further production. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleats with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.43 FOF

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Arch (CWAR9) Size- 2.05m w X 3.60m ht x 0.080m thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.66 BOH

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Arch (CWAR18) Size- 4.55m w X 8.70m ht x 0.080m thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.66 BOH

Designing, Manufacturing as per drawing, Supplying and Installing in position, Architectural Precast Concrete Arch (CWAR19) Size- 4.40m w X 3.36m ht x 0.080m thk. Finishing- with stone texture on surface, including integral pigmentation (precast concrete manufactured as per specifications given below and rate shall be same for all options) including preparation of master prototype in clay/ POP/ Wood and making mould from the same for further producation. Specifications: Precast concrete with compressive strength M-80 Grade. Including steel reinforcement as required, Fixing cleates with Hot Dipped Galvanized (HDG) where exposed, and fasteners- plated from HILTI/KLIMAS/FISCHER or equivalent, Inserts if embedded in Precast concrete should be SS 316. including transportation and conveyance to specific required location, including all necessary accessories for fixing, scaffolding, tools tackels, cleaning at all heights, leads and lifts etc complete. As directed by Engineer-In-Charge. For Building No.66 BOH

Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195 mm size with pillar cock, C.P. Angulars top cock, long thread of approved make continental including SS bottle trap of necessary pipe connection up to the out side face of the wall, having Telephonic Black/Colour Granite of 180 mm thick fixed on Black Kadappa Frame work, etc. Complete as directed by Engineer in charge. SSR 2022-2023 Item No. 48.35 Sr. No. 1651, Page No. 315, As directed by Engineer-In-Charge.

Providing and fixing Table Top White Wash Basin of size 120 x 635 x 405 mm rubber plugs and brass chain, with pillar cock, C.P. Angular stop cock long thread, continental including S.S. bottle trap of approved make having necessary pipe connection up to the out side face of the wall. etc. complete as directed by Engineerin charge. SSR 2022-2023 Item No. 48.36, Sr. No. 1652, Page No. 315, As directed by Engineer-In-Charge.

Providing and constructing Granite Kitchen Platform with fixing of stainless steel sink 600 mm x 450 mm size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 mm thick supports with kadappah top 35 to 40 mm thick and polished granite 16 to 20 mm top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 cm height and top granite of 75 x 40 cm including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.75 m x 1.20 m and height is 0.75 m) SSR 2022-2023 Item No. 41.78, Sr.No. 1369, Page No. 273, As diretced by Engineer-In-Charge.

Providing and fixing white European type Wall -Hung, of size 360 mm x 360 mm x 575 mm with flush valve of approved make including soil pipe, vent pipe up to out side face of wall, 100 mm dia C.I. plug bend inlet pipe all fittings, cutting & making good walls, floors etc as directed by Engineer in charge. SSR 2022-2023 Item No. 48.30, Sr.No. 1646, Page No. 314, As directed by Engineer-In-Charge.

Providing and fixing white Opal series European type Wall-Hung, of size 400 mm x 370 mm x 575mm with approved make flush valve including soil pipe, vent pipe upto outside face of wall, 100mm dia C.I. plug bend inlet pipe all fittings, cutting & making good walls, floors etc as directed by Engineer in charge. SSR 2022-2023 Item No. 48.37, Sr. No. 1653, Page No. 315, As directed by Engineer-In-Charge.

Providing and fixing white glazed Urinal of size 710 x 460 x 300 mm with sensotronic concealed type flushing valve for urinal with complete kit having fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32 mm dia meter P.V.C. flush pipe with fitting and flushing arrangement including lead soil pipe, lead trap & soil pipe connection upto the outside face of wall etc complete. SSR 2022-2023 Item No. 48.43, Sr. No. 1659, Page No. 316, As directed by Engineer-In-Charge.

Providing and fixing C.P. 2 Way BIB cock with wall flange of approved make including necessary sockets / union nut etc. complete as directed by Engineer in charge. SSR 2022-2023 Item No. 48.27, Sr. No. 1644, Page No. 314, As diretced by Rengineer-In-Charge.

Providing and fixing Hands shower (health faucet) with 8 mm dia. 1m long flexible tube having wall hook with approved make including necessary sockets/unionnut etc. complete as directed by Engineer incharge. SSR 2021-2022 Item No. 48.29, Sr. No. 1629, Page No. 227, As directed by Engineer-In-Charge.

Providing and fixing 15 mm dia. Screw down Bib/ Stop Tap of brass including necessary socket union nut complete. SSR 2022-2023 Item No. 41.40, Sr. No. 1334, Page No.270, Bd V 8 Page No. 554.

Providing and fixing 20 mm dia. screw down Bib/ Stop Tap of brass including necessary socket union nut complete. SSR 2022-2023 Item No. 41.41, Sr. No. 1335, Page No. 270, Bd V 8 Page No. 554.

Providing and fixing Sink Cock with regular swinging spout (Wall Mounted Model) with wall flange with approved make incluidng other necessary fitting, etc. complete as directed by Engineer in charge. SSR 2022-2023 Item No. 48.25, Sr. No. 1643, Page No. 314, As diretced by Engineer-In-Charge.

SITC of Electric Hand Drier exposed type AC 240 V (High Speed air) with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline,satisfaction of Engineer-in-charge and site condition. Optima Hand Dryers Sensor Operated Optimum Hand Dryers. Material : AISI 304 Stainless Steel Finish : Satin Make- Jaquar.

SITC of Paper Towel Dispenser including necessary fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline,satisfaction of Engineer-in-charge and site condition. Wall Mounted Paper towel dispensers towels with C/Z folds.capacity: 400-600 C/Z towels,material: AISI 304 stainless steel,finish: satin MAKE - JAQUAR

SITC of stainless steel Towel Rods, 20mm dia. x 600mm long C.P.fixed to wooden plugs with CP screws,brackets including necessary fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline,satisfaction of Engineer-in-charge and site condition. Code:AEC-1111B Towel Rail 18" Make : JAQUAR

Grab bars-Providing SS grab bars set for accessible toilets comprising of 4 nos. Grab bars as specified below.(1 nos. wing grab bar + 1 nos. L shaped grab bar + 2 nos. straight grab bars = 1 typical set) 27a) Swing grab bar (1 NOS) Providing a S.S. 304 SWING HANDICAP GRAB BAR - 700 mm and of DIA: 32MM and thickness 1.5mm of the roved brand and make. 27b) L Shaped grab bar (1 NOS) Providing S.S. 304 L SHAPED DISABLED GRAB BAR of IZE-600MM (H) X 600MM (D) and 32MM DIA. and thickness mm of the approved brand and make. 27c) Straight grab bar (2 NOS) Providing S.STEEL 304 GRAB RAIL (600 MM),32MM DIA. and thickness 1.5mm of the approved brand and make. SSR 2022-2023 Item No. 51.89, Sr. No. 1914, Page No. 373, As diretced by Engineer-In-Charge.

SITC of Soap Dispenser with Sensor type including making the necessary complete as directed .Push Button Soap Dispensers, with C.P.fixed to wooden plugs with CP screws,brackets,including necessary fixing the same with cut-outs, chipping for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Capacity : .8L, Material : ABS, Finish : white/smoked Model No. SDR-WHT-DJ0010F Make : Jaquar

PLUMBING AND SANITARY SITC of CP Toilet Paper Holder fixed with SS screws including necessary fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Make:-Jaquar, - Model - 1151N.

Providing and fixing on walls/ ceiling/ floor 15 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 2022-2023 Item No. 42.55, Sr. No. 1426, Page No. 281, Bd V 5 Page No. 551 and As directed by Engineer-In-Charge.

Providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 2022-2023 Item No. 42.56, Sr. No. 1427, Page No. 281, Bd V 5 Page No. 551 and As directed by Engineer-In-Charge.

Providing and fixing on walls/ ceiling/ floor 25 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 2022-2023 Item No. 42.57, Sr. No. 1428, Page No. 281, Bd V 5 Page No. 551 and As directed by Engineer-In-Charge.

Providing and fixing on walls/ ceiling/ floor 32 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. SSR 2022-2023 Item No. 42.58, Sr. No. 1428, Page No. 281, Bd V 5 Page No. 551 and As directed by Engineer-In-Charge.

Providing and fixing 32 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirement etc. complete.

Providing and fixing 25 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirement etc. complete.

Providing and fixing 15 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirement etc. complete. SSR 2022-2023, Item No. 42.37, Sr. No. 1408, Page No. 277, As directed by Engineer-In-Charge.

Providing and fixing 8 cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete. SSR Sr. No. 1368, Page No.199, Bd V 32, Page No. 567. SSR 2022-2023 Item No. 41.79, Sr. No. 1370, Page No. 273, Bd V 32 Page No. 567.

Providing and fixing 10cm C.I. Nahani Trap including C.I. grating bend and piece of C.I. pipe upto the outside face of the wall complete. SSR Sr. No. 1369, Page No.199, Bd V 32, Page No. 567. SSR 2022-2023 Item No. 41.80, Sr. No. 1371, Page No. 273, Bd V 32 Page No. 567.

Providing and constructing Brick Masonry Inspection Chamber 60cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75 Kilogramwith lid and frame fixed in cement concrete. SSR 2022-2023 Item No. 42.10, Sr. No. 1381, Page No. 274, Bd V 43, Page No. 574.

SITC of PVC, SWR, Type - B, Sewage Downtake, Sewage pipe embedded in wall/ sunk & Rain water Downtake, with rubber ring (conforming to IS : 5382) ACOUSTIC performance ( LOW NOISE ) As per IS: 4985 6 Kg/sqcm, pipe Conforming to IS 13592:92 /1990 & fittings are conforming to IS 14735:99 including all fittings like Single tee, single with with door, swept tee, single tee, connecting coupler, coupler, repair coupler, Swept door tee, reducing tee, bend, reducing swept tee, reducing swept tee, eccentric reducer, cross tee, cross tee with door, reducing cross tee with door, door elbow, bend 45 degree, door bend, socket plugs, single Y, Bush, Single Y with door, reverse Y, Double Y, Double Y with Door, Vent cowl, ventilation conduits, vent cowl with wire mesh, pipe clamps, cleanout, etc. Pipes can be jointed by rubber jointing technique. The pipes to be mounted on support structure OR fixed on to the wall by clamps and hardware or suspended from the ceiling / truss with angle / channel / fabricated iron supports complete with Primer and paint. Civil work like wall cut-out , beam cut out, shall be included in contractors scope. Following are the piping sizes.The same piping will be for waste water and soil water connection inside building and Toilets Blocks. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Application - PVC Soil, waste and ventilating pipes for Waste water and Rain Water Downtake. MAKE : Supreme / Prince / Astral. 40 mm ( Wash Basin Drain )

SITC of PVC, SWR, Type - B, Sewage Downtake, Sewage pipe embedded in wall/ sunk & Rain water Downtake, with rubber ring (conforming to IS : 5382) ACOUSTIC performance ( LOW NOISE ) As per IS: 4985 6 Kg/sqcm, pipe Conforming to IS 13592:92 /1990 & fittings are conforming to IS 14735:99 including all fittings like Single tee, single with with door, swept tee, single tee, connecting coupler, coupler, repair coupler, Swept door tee, reducing tee, bend, reducing swept tee, reducing swept tee, eccentric reducer, cross tee, cross tee with door, reducing cross tee with door, door elbow, bend 45 degree, door bend, socket plugs, single Y, Bush, Single Y with door, reverse Y, Double Y, Double Y with Door, Vent cowl, ventilation conduits, vent cowl with wire mesh, pipe clamps, cleanout, etc. Pipes can be jointed by rubber jointing technique. The pipes to be mounted on support structure OR fixed on to the wall by clamps and hardware or suspended from the ceiling / truss with angle / channel / fabricated iron supports complete with Primer and paint. Civil work like wall cut-out , beam cut out, shall be included in contractors scope. Following are the piping sizes.The same piping will be for waste water and soil water connection inside building and Toilets Blocks. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Application - PVC Soil, waste and ventilating pipes for Waste water and Rain Water Downtake. MAKE : Supreme / Prince / Astral. 75 mm

SITC of PVC, SWR, Type - B, Sewage Downtake, Sewage pipe embedded in wall/ sunk & Rain water Downtake, with rubber ring (conforming to IS : 5382) ACOUSTIC performance ( LOW NOISE ) As per IS: 4985 6 Kg/sqcm, pipe Conforming to IS 13592:92 /1990 & fittings are conforming to IS 14735:99 including all fittings like Single tee, single with with door, swept tee, single tee, connecting coupler, coupler, repair coupler, Swept door tee, reducing tee, bend, reducing swept tee, reducing swept tee, eccentric reducer, cross tee, cross tee with door, reducing cross tee with door, door elbow, bend 45 degree, door bend, socket plugs, single Y, Bush, Single Y with door, reverse Y, Double Y, Double Y with Door, Vent cowl, ventilation conduits, vent cowl with wire mesh, pipe clamps, cleanout, etc. Pipes can be jointed by rubber jointing technique. The pipes to be mounted on support structure OR fixed on to the wall by clamps and hardware or suspended from the ceiling / truss with angle / channel / fabricated iron supports complete with Primer and paint. Civil work like wall cut-out , beam cut out, shall be included in contractors scope. Following are the piping sizes.The same piping will be for waste water and soil water connection inside building and Toilets Blocks. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Application - PVC Soil, waste and ventilating pipes for Waste water and Rain Water Downtake. MAKE : Supreme / Prince / Astral. 90 mm

SITC of PVC, SWR, Type - B, Sewage Downtake, Sewage pipe embedded in wall/ sunk & Rain water Downtake, with rubber ring (conforming to IS : 5382) ACOUSTIC performance ( LOW NOISE ) As per IS: 4985 6 Kg/sqcm, pipe Conforming to IS 13592:92 /1990 & fittings are conforming to IS 14735:99 including all fittings like Single tee, single with with door, swept tee, single tee, connecting coupler, coupler, repair coupler, Swept door tee, reducing tee, bend, reducing swept tee, reducing swept tee, eccentric reducer, cross tee, cross tee with door, reducing cross tee with door, door elbow, bend 45 degree, door bend, socket plugs, single Y, Bush, Single Y with door, reverse Y, Double Y, Double Y with Door, Vent cowl, ventilation conduits, vent cowl with wire mesh, pipe clamps, cleanout, etc. Pipes can be jointed by rubber jointing technique. The pipes to be mounted on support structure OR fixed on to the wall by clamps and hardware or suspended from the ceiling / truss with angle / channel / fabricated iron supports complete with Primer and paint. Civil work like wall cut-out , beam cut out, shall be included in contractors scope. Following are the piping sizes.The same piping will be for waste water and soil water connection inside building and Toilets Blocks. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Application - PVC Soil, waste and ventilating pipes for Waste water and Rain Water Downtake. MAKE : Supreme / Prince / Astral. 110 mm

Providing and fixing P.V.C. Rainwater pipes of 110 mm outer dia meter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592 -1 992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, suchas, offsets, shoes, inluding fixing the pipe on wall us in gapproved wooden cleats projecting 25 mm to 40 mm from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer incharge etc. complete. SSR 2022-2023 Item No. 42.87, Sr.No. 1458, Page No. 283, As directed by Engineer-In-Charge.

Providing & Fixing Greenlam / Equivalent Sturdo Vibrance Serene Toilet Cubicle (of standard dimension 1995mmHX1000mmWX1550mmD, which includes 600mm door size width) OR as directed by Engineer-In-Charge, made of heat, bacterial, water, chemical, scratch, impact and anti bacteria resistant 12mm thick solid compact laminate panels tested by Shriram Test House. Finish of the compact laminate panels should be Suede / *Raw Silk, which includes doors, pilasters & intermediate panels finished with approved texture / shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. The product should have Green Guard Certificate. This also includes providing and Fixing in position necessary hardware made out of Nylon Polyamide Grade-6 & Aluminium powder coated top rail as per manufacturer's specifications & Architects instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Aluminum Top Rail, (5) Coat Hooks, (6) U-Channels, (7) Adjustable Foot, (8) Noise Deafening Tape (9) Screws & Wall plugs etc. The top fitting should consist of Aluminium Powder Coated top rail which will get fixed with Mid & End pilasters. All screws shall be of 304 Grade in stainless steel with satin finish. Top rail is extruded Aluminium shall be powder coated or anodized (Grade 6063 Micron Aluminium). All pilasters are supported by grade- 6 Nylon Polyamide Thermoplastic palm design pedestal footing with non corrosive steel inserts. The base diameter 65mm and neck diameter of 33mm anchored to the floor with grade 304 satin finish stainless steel screws with push fit capping at a clearance height of 150mm.

Providing and fixing 15cm x 10cm Salt Glazed Stoneware Gully Trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. SSR 2022-23, Item No. 42.02, Sr. No. 1373, Page No. 274, Bd V 38, Page No. 572.

Auditorium Chairs (Normal) -Tip up :- Providing and fixing in position of Chairs-Type: Fixed back ‘Tip Up’ chair with yoke type M. S. Frame with single stud floor mounting chair, with fully upholstered seat and back rest using specially mould P. U. Foam with cloth / rexin covering. Central Distance 20” with Spacer 21”. Backrest Height 24”. The Frame : 1 ‘U’ shape yoke type frame made of 65 mm (W) x 5 mm thk M. S. Flat die press bent in power-press, to required curvature, with vertical limbs of 370 to 380 mm height and distance between two vertical limbs to be suitable for chair sitting of 500 to 530 mm handle centre to handle centre. The yoke to be strengthened at curved bottom using 1.5 mm thick triangular shape M. S. Plate wielded to yoke bottom. 2 The yoke to be wielded with stud and floor mounting base plate, the stud made of 1.5 mm (14 SWG) thk 60 x 60 mm M. S. Square Tube with 5 mm thk, 220x115 mm M. S. Plate welded to stud. The stud to be strengthened at back side using triangular shape support made of 1.5mm thk M. S. Sheet. 2- Back rest support of 12 mm thick waterproof plywood of 450 mm (W) x approx 550 to 600 mm (H) hot pressed to required curvature and tailor shaped as per design, with specially moulded minimum 45 mm thk P. U. Foam of density approx. 42 to 45 Kg / Cu. Mtr., covered with cloth covering. The back side of Back-rest to be covered with same cloth, padded with7 mm thk foam inside. 3- Armrests of size 20 mm thk and 35 to 75 mm (W), 375 mm length, with melamine polish to be provided.Miscellaneous: Star Nuts to be embedded in back-rest for bolt fixing of back-rest to frame. M. S. Studs 10 mm dia to seat brass bush with matching hole to studs brazed in frame for fixing seat to frame, with 2.5 mm to3mm thk M. S. ‘L’ angle plate of size 75 to 100 mm (L), 12 mm dia stopper stud. 18 to 20 SWG thick 25 mm x 40 to 50 mm Aluminium number plate with Nos. engraved.12 mm thick 20 to 250 mm (W) and 375 to 450 mm (L) tailor shaped to design and power-press, curved to Match the curvature of back-rest, welded to vertical limbs of yoke to provide tilt angle of 107 to 110 degrees (to horizontal plane) as required. 4 The entire framework shall be powder coated. The Seat and the Back – Rest 1 -19 mm MDF board support base to seat of approx size 450 x 450 mm tailored to required shape, treated with anti-termite coat, specially moulded minimum 62 mm thk mould+13mm high density p.u foam total size=75mm, P. U. Foam Seat cushion of density 45 to 48 KG/Cu. Mr. with crape type wrinkle-free cloth covering fixed to MDF board, with 7 mm foam padding with cloth covered provided to the bottom of seat for acoustic reasons. We are used in seat bracket two springs (3mm thick) for tip-up action.cloth covered ‘End Plates’ to be provided to end chair adjoining to passages. At end chairs. Fixing of chair to floor to be done using 3 Nos. of 10 to 12 mm dia 75 to 100 mm long anchor fasteners per chair.\Anker coach bolt with sturdy wall plugs 10mm x 100mm ‘L’ angle supports for fixing armrests to chair, with inter-coupling between successive chairs. Stand painted with black powder coated. Handel – Wooden with melamine polish/ Foam base/ Plastic. With bottle holder. FR grade Fabric and color of the Cloth - As approved complete.

Auditorium Chairs(VIP) - Push Back Providing and fixing in position of Push Back Chairs Backrest - backrest frame 25mmx25mmx16g square pipe and attached on frame PU mould foam (40 to 50 dencity) with fabric. In backside used A.B.S back shell for chair safety as per design. Backrest are fitted on push back machenism. Backrest size – 465mmWx 720mmD. Mould size – upper side 80mm thick and lower side 60mm thick. Seat – in seat 18mm commercial plywood attach with PU mould (40 to 50 dencity) and fabric. fitted on push back machenism. Seat size – 440mm x 440mm. PU Mould size – front size 120mm thick, backsize – 90mm thick. Push- Back machenism - all brackets, side triangular support, under seat metal sheet support are mfg in 2mm metal sheet and 4 nos. off alinghment strips used in 5 mm. centrally joint 2nos off square pipe 20mmx40mmx16g in between to triangular support. 1 nos high tension spring for push back action attach with rubber stopper centrally in between two pipe. Seat and backrest fitted to bracket with 8mm and 6mm bold with washer. All mechanism painted with black powder coated. Side Stand – 3mm side platein lower side for anchor fitting and upper side used 20mmx40mmx16g square pipe for handle fitting.one stand use in combined two chair fitting with push back machenism. Stand painted with black powder coated. Handel – Wooden with melamine polish/ Foam base/ Plastic. With bottle holder. FR grade Fabric and color of the Cloth - As approved. Foam base Laminated or plain. Chair size – Width – 535mmx560mm. Hight - 1010mm. Depth - 650mm. complete.

ACOUSTIC PANELLING Supply, Installation, testing & commissioning of grooved Acoustic Paneling having system NRC upto 0.88with lineal perforation. The high grade MDF panels shall be melamine laminate of size 600mmx600mmx18mm with 2mm groove at 14 mm pitch, Tongue and Groove edges for seamless mounting having density of 800kg/m3 (base panel confirming to IS 12406 and laminated panel confirming to IS14587). The back of the panels are perforated with anon woven fabric covering of 0.2 mm for providing Sound absorption via the acoustic impedance method. Panel is fixed by using GI Framework2400mmx50mmx0.50mm spaced at 600mmx600 c/c &12 mm ply framework spaced at 400mm centers with suitable brackets and the system is backline with acoustical webbing 50mm@48kg density and along with all accessories example:chicken mesh and all. Approved Makes: Anankon/HunterDouglas/Ecophonis

Providing Podium made in 18 mm Ply wood & Veneer With One shelf of 8” and direct connectivity To Mic and reading light with one mains Connectivity, complete in all respects with Polish etc and as per design and instructions from architect. Size : 1.2 mtr x 0.60 mtr x top – 0.60 mtr as per Architectural & Acoustical Design & Instructions & Complete in all aspects.

Providing and fixing Sign boards made in vineyl and ACP 3 mm sheet as per desired font, language and colour. Indicating toilets, canteen, managers cabin, no smoking, keep clean, do not spit, safety and mandatory instructions, etc. complete.

Providing and Fixing in position of the Auditorium Name in 15 mm PVC sheet in white colour duly painted lettering of approved colour and champhered edges and letter cut on router machine. To be fixed on the facia of stage including necessary scaffolding etc. complete.(Area to be considered in Sq.m. of name letters)

A-Acoustical Wall Panelling Above 2.4 mtr. Lvl.- Providing & Fixing in position, Acoustical Wall Panelling Above 2.4 mtr. Lvl. made from Wood Wool natural board 20 mm thick panels in SS, in front of G. I. framing of ceiling sections at every 600 mm C/C and Intermediate Channels at every 600 mm C/C, in SS screws to proper line and level. The Ceiling Section (The Main Supporting Section to fix Woodwool Tile) shall be of size 80 X 26 X 51 X 0.5 mm, Perimeter Channel: 20 X 28 X 30 X 0.5 mm, Intermediate Channel (Primary Section to support theWall Paneling): 15 X 45 X 15 X 0.9 mm, Ceiling Angle: 25 X 10 X 0.5 mm, in front of Glass wool of 48 kg/sqm- density, 50 mm thick, with chicken mesh on wall side, Primer and OBD Paint including cost of required Cut-Outs, Scaffolding etc, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. (Stage walls, auditorium side & rear wall, Stage Ceiling )

Providing & Fixing in position, Acoustical Wall Panelling made from Fabric (FR Grade Class 1 and P) stretched in grippers 10 mm including cost of required Cut-Outs, Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. (Part walls of auditorium) base rate of fabric Rs 450 per sq. m -

Providing & Fixing in position, Acoustical Wall Panelling made from Decorative Fabric (FR Grade Class 1 and P) stretched in grippers 10 mm with backing of 10mm thick 500gsm density of synthetic wool including cost of required Cut-outs, Scaffolding etc., as per Architectural & Acoustical Design & Instructions & Complete in all aspects. (Part walls of auditorium )

B-Acoustical Wall Panelling Upto 2.4 mtr. Lvl- Providing and fixing in postion of Acoustical Wall Panelling made from 12mm thick Rubber wood strips of 100 mm width in front of G. I. framing of ceiling sections at every 600 mm C/C and Intermediate Channels at every 600 mm C/C, in SS screws to proper line and level. The Ceiling Section (The Main Supporting Section to fix Rubberwood) shall be of size 80 X 26 X 51 X 0.5 mm, Perimeter Channel: 20 X 28 X 30 X 0.5 mm, Intermediate Channel (Primary Section to support theWall Paneling): 15 X 45 X 15 X 0.9 mm, Ceiling Angle: 25 X 10 X 0.5 mm.Make: Gypro (Saint Gobain), in front of Glass wool of 48 kg/cum- 50 mm thick pervaded with Manjarpat Cloth, including cost of required Cut-outs, Melamine Polish & Scaffolding, as per Architectural & Acoustical Design & Instructions & Complete in all aspects. (part of Side walls and Back Wall, Stage Front Wall and PIT Wall)

A: Auditorium Ceiling- Providing and fixing 12.5 mm thk. Plain Gypsum False Ceiling on G.I. frame work, in G. I. ceiling sections at every 600 mm C/C and Intermediate Channels at every 600 mm C/C, in SS screws to proper line and level. Cost to be inclusive of making holes/openings and required framing for fixing electrical Lights/ Fixtures, A.C. grills/Diffusers, Smoke detectors, Sprinklers, etc. Area of electrical fixtures fitted within the ceiling shall not be deducted but a piece of Plywood of thickness 8 mm shall be provided between the adjacent frame/ supports, at no extra cost, to receive Lights, including cutting holes etc, complete. The grid of the frame work shall be supported at every 600mm x 600mm interval by GI L-section, anchored to the slab to support the G.I. framework. All vertical G.I. framework to be anchored to the slab by means of anchor fasteners including all lighting troughs, coffers, cornices and all other related works etc. complete as directed by the Consultant. Including providing and fixing in postion lay in Glasswool of 48 kg/per sqm density, having 50 mm thickness, including cost of approved shade of Plastic Emulsion Paint, cleaning, scaffolding, etc., complete as directed by the Consultants. (Part of auditorium Ceiling)

B: Auditorium Ceiling- Providing and fixing Soft fiber acoustical suspended ceiling system with optra (Bevelled Tegular) edge tiles of size 15mm exposed grid. The tiles should have humidity resistance (RH) of 95%, NRC 0.9 - 1.0, Light reflection- 85%, color-Black, Fire performance UK class 0/ class 1 (BS 476 pt 6& 7) in module size of 600 x 600 x 15mm suitable for green building application with recycled content of 66% GW and 74% RW. The tile shall be laid on precoated GI channel 32 with 15mm wide T section flanges color white having rotary stitching on all T sections i.e. main runner, 1200mm and 600mm cross tees with a web height of 32 mm and a load carrying capacity of 7 kg/m2 with a minimum pull out strength of 100 kg. The T section have a galvanising of 90 gms per m2 and need to be installed with suspension system. The tile and the grid system used together should carry a 10 year warrenty. Products approved as per GRIHA and BS 476 etc. complete as directed by the Consultants. (Auditorium Ceiling) SSR 2022-23, Item No. 38.47, Sr. No. 1187, Page No. 242, As diretced b y Enginer-In-Charge.

Providing & fixing in position Stage flooring using 37mm thick (4''w x 5' L ) T. W. planks having tongue & grove on 18 mm water proof ply screwed to Teak wood frame of 50 x 50 mm wooden sections at 600mm c to c on stage surface including two coats of melamine polish, as per Architectural & Acoustical Design & Instructions & Complete in all aspects.

Excavation for foundation / pipe trenches in earth, soils of all types, sand, gravel and soft murum, including removing the excavated material upto a distance of 50 metres and lifts as below, stacking and spreading as directed, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd-A-1/259) Lift Upto 1.50m. - MJP-SSR-2021-22 - SECTION-E, Item No.1, Page No.42.

Excavation for foundation / pipe trenches in hard murum including removing the excavated material upto a distance of 50 M and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd- A-2/259) Lift Upto 1.50m - MJP-SSR-2021-22 - SECTION-E, Item No.2, Page No.42.

Excavation for foundation / pipe trenches in soft rock and old cement and lime masonry foundation asphalt road including removing the excavated material upto a distance of 50 M beyond the area and lifts as below, stacking as directed by Engineer-in- charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd-A-4/259) Lift Upto 1.50m MJP-SSR-2021-22 - SECTION-E, Item No.5, Page No.42.

Excavation for foundation / pipe trenches in hard rock and concrete by chiselling, wedging, line drilling by mechanical means or by all means other than blasting, including trimming and levelling the bed, removing th eexcavated material upto a distance of 50metres beyond the area and lifts as below, stacking as directed by Engineer-In-Charge, normal dewatering, excluding backfilling, etc. complete by all meams. (Bd-A-6/259) Lift Upto 1.50m MJP-SSR-2021-22 - SECTION-E, Item No.6, Page No.43.

Excavation for foundation / pipe trenches in hard murum including removing the excavated material upto a distance of 50 M and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd- A-2/259) Lift beyond 1.50m MJP-SSR-2021-22 - SECTION-E, Item No.1+4, Page No.42.

Excavation for foundation / pipe trenches in hard murum including removing the excavated material upto a distance of 50 M and lifts as below, stacking and spreading as directed by Engineer-in-charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd- A-2/259) Lift beyond 1.50m MJP-SSR-2021-22 - SECTION-E, Item No.2+4, Page No.42.

Excavation for foundation / pipe trenches in soft rock and old cement and lime masonry foundation asphalt road including removing the excavated material upto a distance of 50 M beyond the area and lifts as below, stacking as directed by Engineer-in- charge, normal dewatering, preparing the bed for foundation and excluding backfilling, etc. complete. (Bd-A-4/259) Lift beyond 1.50m MJP-SSR-2021-22 - SECTION-E, Item No.5+9, Page No.42 and 43.

Excavation for foundation / pipe trenches in hard rock by controlled blasting, including trimming and levelling the bed by chiselling where necessary and removing the excavated material and stacking it in measurable heaps within a distance of 50 metres from the area and lifts as below, normal dewatering, excluding backfilling, etc. complete. (Bd-A-5/259) Lift beyond 1.50m MJP-SSR-2021-22 - SECTION-E, Item No.6+9, Page No.43.

Dewatering the excavated trenches and pools of water in the building trenches / pipeline trenches, well works by using pumps and other devices including disposing off water to safe distance as directed by Engineer-in-charge (including cost of machinery, labour, fuel), etc. complete. (Bd-A-9/261) MJP-SSR-2021-22 - SECTION-E, Item No.14, Page No.45.

Filling in the trenches with available excavated stuff with soft material first over pipeline and then hard material in 15 cm layers with all leads and lifts including consolidation, surcharging etc. complete. MJP-SSR-2021-22 - SECTION-E, Item No.15, Page No.45.

Valve chamber with cast iron manhole frame and covers Providing and constructing B.B. masonry valve chambe with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportion, 12 mm thick cement plaster in CM 1:4 proportion on both sides with providing and fixing C.I. manhole frame and cover in RCC 1:2:4 coping or RCC 1:2:4 proportion x 15 cm thick slab, etc. complete as directed by Engineer-in-charge As above of 0.6 M x 0.45 M internal size and depth upto 0.9 M with 60 x 45 cm size CI manhole frame and cover of 40 kg. MJP-SSR-2021-22 - SECTION-L, Item No.2-A, Page No.221.

Valve chamber with cast iron manhole frame and covers Providing and constructing B.B. masonry valve chambe with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportion, 12 mm thick cement plaster in CM 1:4 proportion on both sides with providing and fixing C.I. manhole frame and cover in RCC 1:2:4 coping or RCC 1:2:4 proportion x 15 cm thick slab, etc. complete as directed by Engineer-in-charge As above of 0.6 M x 0.45 M internal size and depth upto 0.9 M with 60 x 45 cm size CI manhole frame and cover of 40 kg. As above of 0.90 M x 0.60 M internal size and depth upto 1.5 M with 90 x 60 cm size CI manhole frame and cover of 50 kg. MJP-SSR-2021-22 - SECTION-L, Item No.2-C, Page No.221.

Valve chamber with cast iron manhole frame and covers Providing and constructing B.B. masonry valve chambe with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportion, 12 mm thick cement plaster in CM 1:4 proportion on both sides with providing and fixing C.I. manhole frame and cover in RCC 1:2:4 coping or RCC 1:2:4 proportion x 15 cm thick slab, etc. complete as directed by Engineer-in-charge As above of 0.6 M x 0.45 M internal size and depth upto 0.9 M with 60 x 45 cm size CI manhole frame and cover of 40 kg. As above of 0.90 M x 0.60 M internal size and depth upto 1.5 M with 90 x 60 cm size CI manhole frame and cover of 50 kg. As above of 1.2 x 1.2 M internal size and depth upto 2.5 M with 53 cm dia CI manhole frame and cover of 90 kg. fixed in RCC slab. MJP-SSR-2021-22 - SECTION-L, Item No.2-E, Page No.221.

Valve chamber with cast iron manhole frame and covers Providing and constructing B.B. masonry valve chambe with 15 cm thick 1:3:6 proportion PCC bedding, excluding excavation, B.B. masonry in CM 1:5 proportion, 12 mm thick cement plaster in CM 1:4 proportion on both sides with providing and fixing C.I. manhole frame and cover in RCC 1:2:4 coping or RCC 1:2:4 proportion x 15 cm thick slab, etc. complete as directed by Engineer-in-charge As above of 0.6 M x 0.45 M internal size and depth upto 0.9 M with 60 x 45 cm size CI manhole frame and cover of 40 kg. As above of 0.90 M x 0.60 M internal size and depth upto 1.5 M with 90 x 60 cm size CI manhole frame and cover of 50 kg. As above of 1.2 x 1.2 M internal size and depth upto 2.5 M with 53 cm dia CI manhole frame and cover of 90 kg. fixed in RCC slab. As above of 1.5 x 1.5 M internal size and depth upto 3.0 M with 53 cm dia CI manhole frame and cover of 90 kg. fixed in RCC slab. MJP-SSR-2021-22 - SECTION-L, Item No.2-F, Page No.221.

Providing supplying in standard length (PE material) HDPE Double wall corrugated pipe for non pressure underground drainage and sewerage with smooth internal & corrugated external surface confirming to IS 16098:Part-2 2013 with spigot or plain end with necessary jointing material coupler including transportation and freight charges, inspection charges, loading and unloading charges, conveyance to departmental store and stacking the same in closed shade duly protecting from direct sun ray and rains excluding GST levied by Gol and GoM in all respect, etc. complete. SN4 and SN8, ID 150MM DIA MJP-SSR-2021-22 - SECTION-I(IX), Item No.4-ii, Page No.116.

Providing supplying in standard length (PE material) HDPE Double wall corrugated pipe for non pressure underground drainage and sewerage with smooth internal & corrugated external surface confirming to IS 16098:Part-2 2013 with spigot or plain end with necessary jointing material coupler including transportation and freight charges, inspection charges, loading and unloading charges, conveyance to departmental store and stacking the same in closed shade duly protecting from direct sun ray and rains excluding GST levied by Gol and GoM in all respect, etc. complete. SN4 and SN8, ID 200MM DIA MJP-SSR-2021-22 - SECTION-I(IX), Item No.4-iv, Page No.116.

Providing supplying in standard length (PE material) HDPE Double wall corrugated pipe for non pressure underground drainage and sewerage with smooth internal & corrugated external surface confirming to IS 16098:Part-2 2013 with spigot or plain end with necessary jointing material coupler including transportation and freight charges, inspection charges, loading and unloading charges, conveyance to departmental store and stacking the same in closed shade duly protecting from direct sun ray and rains excluding GST levied by Gol and GoM in all respect, etc. complete. SN4 and SN8, ID 250MM DIA MJP-SSR-2021-22 - SECTION-I(IX), Item No.4-v, Page No.116.

Lowering, Laying and Jointing (PE material) HDPE double wall corrugated pipe for non pressure underground by heating to the ends of pipes with the help of tefflon coated electric heater to the required temparature and then pressing the ends together against each other, to form a monolithic & leak proof joint by thermosetting process. The pressing may be required to be done with Jacks/ Hydraulic Jacks/Butt fusion machine etc. complete with all materials labours as directed by Engineer-in-charge. SN4 and SN8, ID 150MM DIA MJP-SSR-2021-22 - SECTION-I (IX), Item No.5-ii, Page No.116.

Lowering, Laying and Jointing (PE material) HDPE double wall corrugated pipe for non pressure underground by heating to the ends of pipes with the help of tefflon coated electric heater to the required temparature and then pressing the ends together against each other, to form a monolithic & leak proof joint by thermosetting process. The pressing may be required to be done with Jacks/ Hydraulic Jacks/Butt fusion machine etc. complete with all materials labours as directed by Engineer-in-charge. SN4 and SN8, ID 200MM DIA MJP-SSR-2021-22 - SECTION-I (IX), Item No.5-iv, Page No.116.

Lowering, Laying and Jointing (PE material) HDPE double wall corrugated pipe for non pressure underground by heating to the ends of pipes with the help of tefflon coated electric heater to the required temparature and then pressing the ends together against each other, to form a monolithic & leak proof joint by thermosetting process. The pressing may be required to be done with Jacks/ Hydraulic Jacks/Butt fusion machine etc. complete with all materials labours as directed by Engineer-in-charge. SN4 and SN8, ID 250MM DIA MJP-SSR-2021-22 - SECTION-I (IX), Item No.5-v, Page No.116.

Providing ISI standard R.C.C. pipes in standard lengths of following class and diameter suitable for either collar joints or rubber ring joints, excluding GST lev-ied by GOI & GOM in all respect including inspec- tion charges, transport to departmental stores, unloading and stacking etc. complete as per IS-458/1988. Note: One collar should be supplied with each full length plain ended RCC pipe, cost including in rates below. One rubber ring should be supplied with each full length of socketed pipe, cost included in rates below. Class NP-II ( For 2.00 m. length ) 200mm dia. MJP-SSR-2021-22 - SECTION-I (V), Item No.1-d-iv, Page No.96.

Providing ISI standard R.C.C. pipes in standard lengths of following class and diameter suitable for either collar joints or rubber ring joints, excluding GST lev-ied by GOI & GOM in all respect including inspec- tion charges, transport to departmental stores, unloading and stacking etc. complete as per IS-458/1988. Note: One collar should be supplied with each full length plain ended RCC pipe, cost including in rates below. One rubber ring should be supplied with each full length of socketed pipe, cost included in rates below. Class NP-II ( For 2.00 m. length ) 250mm dia. MJP-SSR-2021-22 - SECTION-I (V), Item No.1-d-vi, Page No.96.

Lowering, laying and jointing in proper grade and alignment R.C.C. pipes with collar joints in C.M.1:1 proportion or socketed R.C.C. pipes with rubber joints (excluding cost of rubber ring or R.C.C. collar,) including cost of conveyance from stores to site of work, cost of jointing material, labour, etc. complete as directed by Engineerin- charge (For all class of pipes.) as per IS- 783-1985. 200mm dia. MJP-SSR-2021-22 - SECTION-I (V), Item No.2-iv, Page No.98.

Lowering, laying and jointing in proper grade and alignment R.C.C. pipes with collar joints in C.M.1:1 proportion or socketed R.C.C. pipes with rubber joints (excluding cost of rubber ring or R.C.C. collar,) including cost of conveyance from stores to site of work, cost of jointing material, labour, etc. complete as directed by Engineerin- charge (For all class of pipes.) as per IS- 783-1985. 250mm dia. MJP-SSR-2021-22 - SECTION-I (V), Item No.2-vi, Page No.98.

Providing and laying in situ Ready Mix Cement Concrete grade of trap / granite / quartzite / gneiss metal for RCC works in foundation like raft. grillage, strip foundation and footing of RCC column and steel stanchions including normal dewatering, form work, compaction. finishing and curing including transporting from mixin plant upto distance of 25 km., pouring the cagcrete at work site for 1.5 M lift above G.L. and 5.0 IM lift below G.L etc. complete. M-30 MJP-SSR-2021-22 - SECTION-G, Item No.10-d, Page No.54.

Providing and fixing in position Steel bar reinforcement of various diameters for RCC Pipes , caps , foundations , footings , slabs, beams , columns , canopies , staircases, newels, chajjas,lintels,pardies, copings , fins , arches etc as per detialed designs, drawings and schedules including cutting bending hooking the bars , binding the wires or tack welding and supporting as required , etc complete (including cost of binding wire) (Bd-F-17/306) MJP-SSR-2021-22 - SECTION-G, Item No.8-b, Page No.52.

Providing and casting in situ C.C. of trap / granite/ quartzite / gneiss metal of approved quality for RCC works as per detailed drawings and designs or as directed by Engineer-in-charge including normal dewatering, centering, form work, compaction, finishing the formed surfaces with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface wherever necessary or roughening if special finish is to be provided and curing, etc. complete. (By weigh batching and mix design for M-250 and M-300 only. Use of L&T, A.C.C., Ambuja, Birla Gold, Manikgad, Rajashree, etc. cement is permitted.) (Excluding M.S. or Tor reinforcement) M-30 MJP-SSR-2021-22 - SECTION-G, Item No.5-d, Page No.50.

Providing and laying in situ Cement Concrete M-15 of trap/ granite / quartzite / gneiss metal for foundation and bedding including bailing out water, form work, compaction, curing, etc. complete. (Cement 5.90 bags / cum) MJP-SSR-2021-22 - SECTION-G, Item No.1-b, Page No.49.

Providing and fixing on walls/ceiling/floor 15 NB dia. Rigid- UPVC pipe SCH 80 with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ceiling/floor 25 NB dia. Rigid- UPVC pipe SCH 80 with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ceiling/floor 32 NB dia. Rigid- UPVC pipe SCH 80 with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ceiling/floor 40 NB dia. Rigid- UPVC pipe SCH 80 with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and fixing on walls/ceiling/floor 50 NB dia. Rigid- UPVC pipe SCH 80 with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Providing and supplying in standard lengths HDPE Pipe , Polyethelene Pipes, confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete. 16 Kg/Sq. cm : 63mm dia HDPE Pipe burried underground inter building MJP-SSR-2021-22 SECTION I -(XIII) 1. e

Providing and supplying in standard lengths HDPE Pipe , Polyethelene Pipes, confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete. 16 Kg/Sq. cm : 75mm dia HDPE Pipe burried underground inter building MJP-SSR-2021-22-SECTION I -(XIII) 1. f

Lowering, Laying and Jointing H. D. P. E./M. D. P. E. pipes in proper position including all specials by compression fitting/electrofusion and butt fusion jointing procedure as per relevent IS Code complete with all materials for jointing procedure like Electrofusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II. 63mm MJP-SSR-2021-22-SECTION I -(XIII) 2. vi

Lowering, Laying and Jointing H. D. P. E./M. D. P. E. pipes in proper position including all specials by compression fitting/electrofusion and butt fusion jointing procedure as per relevent IS Code complete with all materials for jointing procedure like Electrofusion machine, Electric heater/butt fusion welding machine with hydraulic jack, top loading clamp etc. and all labours as directed by engineer in charge as per IS-7634 Part II. 75mm MJP-SSR-2021-22-SECTION I -(XIII) 2. vii

Providing and supplying in ISI mark rigid PVC- O class-500 s/s pipe (push on joints) pressure pipes confirming to IS specifications no 16647- 2017 inclusive cost of EPDM gasket seals on joints including all statutory duties excluding GST levied by Government of India and Government of Maharashtra in all respect including third party inspection charges of agency approved by MJP, transit insurance loading, unloading charges conveyance to the departmental store / site and stacking the same in closed shade duly protected from sunrays etc complete. Class-500 PN-16 110mm

Lowering, laying and jointing with P.V.C. pipes and specials of following class and diameter including cost of conveyance from stores to site of works including cost of all labour, material, except cement solvent, rubber ring, as per IS code, etc. complete (with cement solvent joint / ring fit joint). Class-500 PN-16 110mm MJP-SSR-2021-22-SECTION I-(II) 4. b)

Providing ISI standard R.C.C. pipes in standard lengths of following class and diameter suitable for either collar joints or rubber ring joints, excluding GST lev-ied by GOI & GOM in all respect including inspec- tion charges, transport to departmental stores, unloading and stacking etc. complete as per IS-458/1988. Note :One collar should be supplied with each full length plain ended RCC pipe, cost including in rates below. One rubber ring should be supplied with each full length of socketed pipe, cost included in rates below. Class-NP-II (2.0m Length) 200mm MJP-SSR-2021-22-SECTION I -(V) 1. d. iv

Lowering, laying and jointing in proper grade and alignment R.C.C. pipes with collar joints in C.M.1:1 proportion or socketed R.C.C. pipes with rubber joints (excluding cost of rubber ring or R.C.C. collar,) including cost of conveyance from stores to site of work, cost of jointing material, labour, etc. complete as directed by Engineerin- charge (For all class of pipes.) as per IS- 783-1985. 200mm MJP-SSR-2021-22-SECTION I -(V) 2. d. iv

Providing and fixing 15 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirement etc. complete.

Providing and fixing 25 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirement etc. complete.

Providing and fixing 32 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirement etc. complete.

Providing and fixing 40 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.

Providing and fixing 50 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.

Providing and fixing 63 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.

Providing and fixing 75 mm. dia Ball cock medium type with PVC float including sockets and necessary fittings and tested as per municipal requirements etc. complete.

Providing and supplying ISI mark CI D/F reflux valves (non-return valves ) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Reflux valves as per I.S.5312 Part I (1984) without by Pass arrangement 40mm dia.

Providing and supplying ISI mark CI D/F reflux valves (non-return valves ) of following dia including railway freight, inspection charges, unloading from railway wagon, loading into truck, transportation upto departmental stores, unloading, stacking excluding GST levied by GOI & GOM in all respect etc. complete. Reflux valves as per I.S.5312 Part I (1984) without by Pass arrangement 80mm dia. MJP-SSR-2021-22-SECTION-I (XII) 1. C) iii

Lowering, laying and jointing in position following C.I.D/F Reflex valves, Butterfly valves and Sluice valves including cost of all labour jointing material, including nut bolts and giving satisfactory hydraulic testing etc. complete. (Rate for all class of valves.) 80mm MJP-SSR-2021-22-SECTION-I (XII) 4. iii

Supplying & erecting cast iron double flange butterfly valve of size 75/80 mm dia. complete as per specification no. FF-VL/BFV

Supplying & erecting cast iron double flange butterfly valve of size 100 mm dia. complete as per specification no. FF-VL/BFV

Providing and supplying Air Valves as per IS- 14845-2000 and MJP’s standard specifications of approved make and quality of following diameters including railway freight, inspection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores, unloding and stacking excluding GST levied by GOI & GOM in all respect etc. complete.Air Valve Single Ball Flanged / Screwed Type - PN -1.6. 12/15mm MJP-SSR-2021-22-SECTION XIII 5. b) i

SITC of approved make pilot operated Water Pressure regulating Valve (PRV's) conforming to ASTM standards with union etc. Z3 sealed spring cage and stainless steel corrosion resistant adjusting cage screws, Integral stainless steel strainer, Replaceable seat module, cast copper silicon alloy body, NPT threaded female union inlet x NPT female outlet, Temperature Range (0.5°C – 71°C), Maximum Working Pressure: 10 bar, Adjustable Reduced Pressure Range:25 – 75psi. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Make : Watt/ Flomatic. 15mm dia.

SITC of approved make pilot operated Water Pressure regulating Valve (PRV's) conforming to ASTM standards with union etc. Z3 sealed spring cage and stainless steel corrosion resistant adjusting cage screws, Integral stainless steel strainer, Replaceable seat module, cast copper silicon alloy body, NPT threaded female union inlet x NPT female outlet, Temperature Range (0.5°C – 71°C), Maximum Working Pressure: 10 bar, Adjustable Reduced Pressure Range:25 – 75psi. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Make : Watt/ Flomatic. 25mm dia.

SITC of approved make pilot operated Water Pressure regulating Valve (PRV's) conforming to ASTM standards with union etc. Z3 sealed spring cage and stainless steel corrosion resistant adjusting cage screws, Integral stainless steel strainer, Replaceable seat module, cast copper silicon alloy body, NPT threaded female union inlet x NPT female outlet, Temperature Range (0.5°C – 71°C), Maximum Working Pressure: 10 bar, Adjustable Reduced Pressure Range:25 – 75psi. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Make : Watt/ Flomatic. 32mm dia.

SITC of approved make pilot operated Water Pressure regulating Valve (PRV's) conforming to ASTM standards with union etc. Z3 sealed spring cage and stainless steel corrosion resistant adjusting cage screws, Integral stainless steel strainer, Replaceable seat module, cast copper silicon alloy body, NPT threaded female union inlet x NPT female outlet, Temperature Range (0.5°C – 71°C), Maximum Working Pressure: 10 bar, Adjustable Reduced Pressure Range:25 – 75psi. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Make : Watt/ Flomatic. 40mm dia.

SITC of approved make pilot operated Water Pressure regulating Valve (PRV's) conforming to ASTM standards with union etc. Z3 sealed spring cage and stainless steel corrosion resistant adjusting cage screws, Integral stainless steel strainer, Replaceable seat module, cast copper silicon alloy body, NPT threaded female union inlet x NPT female outlet, Temperature Range (0.5°C – 71°C), Maximum Working Pressure: 10 bar, Adjustable Reduced Pressure Range:25 – 75psi. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. Make : Watt/ Flomatic. 50mm dia.

Water Hammer Arrestor with complete accessories, 50mm

Water Hammer Arrestor with complete accessories, 40mm

Water Hammer Arrestor with complete accessories, 32mm

Water Hammer Arrestor with complete accessories, 25mm

Water Hammer Arrestor with complete accessories, 15mm

SITC of Strainer Y type CS body with SS 304 mesh , ISI marked tested to 12 kg/ sq. cm pressure Rate quoted shall include for supply and providing with ,necessary fitting gaskets, G.I.nuts-bolts & washers of following sizes. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting Complete to be erected as required as per site condition & guideline & satisfaction of Engineer-in-charge. Make : Flowjet/Merck. 80mm

Supplying and erecting cast iron foot valve ball type/flap type of size 80 mm dia with strainer for negative suction complete as per specification no. FF-VL/FV

SITC of Water Meter, Application for measuring Water Consumption, Temperature of water not more than 50deg. C, MOC of Water Meter Body: Brass, End Connection - threaded end, MOC of gear: Stainless Steel, Max. Pressure : 10 kg/sq.cm, Max. Flowrate: 10 cu.m/hr, Application: Water, Conforming from ISO: 4064, Rate shall include for supply and providing companion barrel nipples, hex nipple, Teflon tape and flanges etc. Meter shall have necessary input signal to BMS (RS-485) with BACKNET protocol. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. of following sizes. MAKE : Accuflow/Capston/Kranti. 15mm

SITC of Water Meter, Application for measuring Water Consumption, Temperature of water not more than 50deg. C, MOC of Water Meter Body: Brass, End Connection - threaded end, MOC of gear: Stainless Steel, Max. Pressure : 10 kg/sq.cm, Max. Flowrate: 10 cu.m/hr, Application: Water, Conforming from ISO: 4064, Rate shall include for supply and providing companion barrel nipples, hex nipple, Teflon tape and flanges etc. Meter shall have necessary input signal to BMS (RS-485) with BACKNET protocol. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. of following sizes. MAKE : Accuflow/Capston/Kranti. 25mm

SITC of Water Meter, Application for measuring Water Consumption, Temperature of water not more than 50deg. C, MOC of Water Meter Body: Brass, End Connection - threaded end, MOC of gear: Stainless Steel, Max. Pressure : 10 kg/sq.cm, Max. Flowrate: 10 cu.m/hr, Application: Water, Conforming from ISO: 4064, Rate shall include for supply and providing companion barrel nipples, hex nipple, Teflon tape and flanges etc. Meter shall have necessary input signal to BMS (RS-485) with BACKNET protocol. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. of following sizes. MAKE : Accuflow/Capston/Kranti. 32mm

SITC of Water Meter, Application for measuring Water Consumption, Temperature of water not more than 50deg. C, MOC of Water Meter Body: Brass, End Connection - threaded end, MOC of gear: Stainless Steel, Max. Pressure : 10 kg/sq.cm, Max. Flowrate: 10 cu.m/hr, Application: Water, Conforming from ISO: 4064, Rate shall include for supply and providing companion barrel nipples, hex nipple, Teflon tape and flanges etc. Meter shall have necessary input signal to BMS (RS-485) with BACKNET protocol. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. of following sizes. MAKE : Accuflow/Capston/Kranti. 40mm

SITC of Water Meter, Application for measuring Water Consumption, Temperature of water not more than 50deg. C, MOC of Water Meter Body: Brass, End Connection - threaded end, MOC of gear: Stainless Steel, Max. Pressure : 10 kg/sq.cm, Max. Flowrate: 10 cu.m/hr, Application: Water, Conforming from ISO: 4064, Rate shall include for supply and providing companion barrel nipples, hex nipple, Teflon tape and flanges etc. Meter shall have necessary input signal to BMS (RS-485) with BACKNET protocol. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. of following sizes. MAKE : Accuflow/Capston/Kranti. 50mm

SITC of Water Meter, Application for measuring Water Consumption, Temperature of water not more than 50deg. C, MOC of Water Meter Body: Brass, End Connection - threaded end, MOC of gear: Stainless Steel, Max. Pressure : 10 kg/sq.cm, Max. Flowrate: 10 cu.m/hr, Application: Water, Conforming from ISO: 4064, Rate shall include for supply and providing companion barrel nipples, hex nipple, Teflon tape and flanges etc. Meter shall have necessary input signal to BMS (RS-485) with BACKNET protocol. with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. of following sizes. MAKE : Accuflow/Capston/Kranti. 63mm

Supplying and installing pressure gauge of 100 mm dia., 0- 300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, and G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying & erecting Water level controller 230/415 V AC., Two way for under ground tank operation only.

Drinking water Kiosk with cooling SS 150 litres Stainless Steel Plain and Cold Water Cooler PC15150 -3T

RO+UV 50 L/Hour Wall mounted ABS Food Grade Plastic 230 V AC

SITC of pilot operated Water float valve inside water storage tank. The pressure rating sustain upto 10 kg , MOC : SS Mounting to be do be with extended arm with proper mounting and fixing to water inlet.with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. MAKE : Watt / Varie. 40mm

SITC of pilot operated Water float valve inside water storage tank. The pressure rating sustain upto 10 kg , MOC : SS Mounting to be do be with extended arm with proper mounting and fixing to water inlet.with including necessary accessories for fixing the same with cut-outs, chipping , screws, for recessing & grouting complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. MAKE : Watt / Varie. 63mm

Supply, Installation, testing and commissioning of Modular Water Storage Tank GI Circular with bolted structure 2.5mm minimum thickness panels and reinforced PVC liners inside , wind bracing on all the rings roof with trusses and 0.5 mm thick 550 NPA Strength# 01 & 02 - capacity - 30 KL ( For STP # 01 AND STP # 02) Recycled Water Tank .The rate quoted shall include for supply with providing necessary jointing materials & accessories etc. a. 100 MM Outlet Nozzle with Vortex : 2 Nos each b. 80 MM Outlet Nozzle with Vortex : 2 Nos each c. 65 mm Outlet Nozzle with Vortex : 4 Nos each d. Overflow 40 mm : 1 Nos each e. Drain outlet 40 mm : 1 Nos each f. Level Indicator : 1 Nos each g. Air Vent : 2 nos each h. Ladders for maintainance : 1 Nos each i. Manhole : 2 Nos each j. Hole Provision for Level Sensor : 2 Nos each k. Safety platforms : 1 Nos

SITC of FRP Buffer Tanks 20 litre with proper coating including fittings and accessories in all respect. Leakproof nozzle cutout for water inlet and outlet , drain, overflow to be done. Tank alignment, interconnection with flanges, isolation valve, nut bolt, washers etc with required fittings all to be considered.with including necessary accessories for fixing the same with complete to be erected as required at site & as per guideline, satisfaction of Engineer-in-charge and site condition. MAKE :Sintex/ Fibertech / Polyplast ( Application : Water Storage)

Excavation for Roadway in Earth, Soil of all sorts, sand, gravel or soft murum including dressing section to the required grade camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 m and spreading for embankment or stacking as directed. SSR 2022-23 Item No. 2.11, Sr.No.87, Page No.23, MORTH 301.

Excavation for Roadway in Hard Murum and boulder including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 m and spreading for embankment or stacking as directed. SSR 2022-23 Item No. 2.13, Sr.No. 88, Page No. 24, MORTH 301.

Excavation for Roadway in Soft Rock including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 m and spreading or stacking as directed. SSR 2022-23 Item No. 2.14, Sr. No. 89, Page No. 24, MORTH 301.

Excavation for Roadway in Hard Rock by wedging and chiselling or line drilling including dressing section to the required grade, camber and side slopes and conveying the excavated materials with all lifts upto a lead of 50 m and spreading for embankment or stacking as directed. SSR 2022-23 Item No. 2.16, Sr. No. 91, Page No. 24, MORTH 301.

Conveying materials obtained from road cutting including all lifts, laying in layers of 20 cm. to 30 cm. breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard proctor density for a lead of over 50 m to 300 m. inclusive from the site of excavation to the site of deposition as directed. SSR 2022-23 Item No. 2.25, Sr. No. 99, page No. 24, MORTH 305.

Conveying materials obtained from road cutting including all lifts, laying in layers of 20 cm. to 30 cm. breaking clods, dressing to the required lines, curves, grades and section, watering and compacting to not less than 97% of standard proctor density for a lead of over 300 m to 500 m. inclusive from the site of excavation to the site of deposition as directed. SSR 2022-23 Item No. 2.26, Sr. No. 99, Page No. 25, MORTH 305.

Providing earth work in Embankment with approved materials obtained from other sources, including all lead and lifts, laying in layers of 20 centimetre to 30 centimetre thickness breaking clods, dressing to the required lines, curves, grades and section, watering and compaction with vibratory roller with V-Sat attachment to achieve not less than 97% of standard proctor density etc. complete (Material obtained from Other sources). SSR 2022-23 Item No. 2.28, Sr. No. 101, Page No. 25, MORTH 305.

Transportion 1Km of excavated material from Site. SSR 2022-23, Statement C1 (with machine loading) Page No. 559.

Providing Hard Murum side shoulder including supplying hard murum at the road site, including spreading and compacting for sidewidth layers on each side with power roller including artificial watering etc complete. SSR 2022-2023 Item No. 2.29AA

Construction of granular sub-base by Plant Mix Method by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with Motor Grader/ Paver on prepared surface and compacting with vibratory power roller to achieve the desired density complete as per clause 401. Plant Mix Method and Grading II Material. SSR 2022-23 Item No. 3.02, Sr.No. 114, Page No. 27, MORTH-401.

Providing and laying 125 micron Low Density Polyethylene (LDPE) sheet confirming to IS 3395:1997 below concrete pavement including all materials and labour complete. SSR 2022-23, Item No. 5.19, Sr. No. 187, Page No.44, MORTH-602.5

Providing and laying Concrete Pipe of I.S.NP. class of 300 mm diameter in proper line, level and slope including necessary collars, excavation, laying, fixing with collars in cement mortar 1:1 and refilling the trench complete. SSR 2022-23, Item No. 42.09, Sr.No. 1380, Page No.274, Bd.V, Page No. 573.

Providing and laying cement Concrete Pipe of I.S. 458:2003 Non Pressure-2 class of 450 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 complete. SSR 2022-23, Item No. 11.08, Sr. No. 384, Page No.81, CD 7, Page No. 162.

Providing and laying in situ/ ready mix M-20 RCC of trap metal for RCC work of ballast walls and Kerbs and box returns including scaffolding, compaction, formwork finishing and curing etc. complete, excluding reinforcement, with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant/ pan mixer and fine agreegates of required specifications (VSI sand finely washed etc.) SSR 2022-23, Item No. 14.44 a, Sr. No. 476, Page No.96, BR 50, Page No. 143 and B7, Page No.38.

Providing and laying Cement Concrete Pipe of I.S. 458:2003 Non Pressure-3 class of 600 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 complete. SSR 2022-23, Item No. 11.14, Sr. No.390, Page No. 82, CD 7, Page no.162.

Providing and laying Cement Concrete Pipe of I.S. 458:2003 Non Pressure-3 class of 900 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 complete. SSR 2022-23, Item No. 11.16, Sr. No.392, Page No. 82, CD 7, Page No. 162.

Providing and laying cement concrete pipe of I.S. 458:2003 Non Pressure-3 class of 1200 milimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 complete. SSR-2022-23, Item No. 11.18, Sr. No.394, Page No.82, CD-7 Page No.162.

Providing and laying in situ/ ready mix M-20 controlled reinforced cement concrete of trap metal for Raft slab including "V" haunches, formwork, scaffolding, compaction by vibrating, finishing curing etc. complete, RCC Grade with concrete Batch mix plant (Pan mixer) etc. complete. with fine agreegates of required specifications (VSI sand finely washed etc.) SSR 2022-23, Item No. 17.32, Sr. No. 620, Page No. 131, MORT&H (5th Rev.) 1700,2304.

Providing and laying Cast in situ/ Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Pardi of required thickness including centering, formwork, cover blocks, laying/ pumping, compacting, curing, finishing and rougheningthem if special finish is to be provided and curing complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Crushed sand V.S.I. Grade). SSR 2022-23, Item No. 26.17, Sr. No. 860, Page No. 185, Bd F-11, Page No. 304 and B7, Page No. 38.

Providing and fixing Ductile Iron Manhole Cover of light/medium/heavy duty with frame of any size over inspection chamber etc. complete (Prior permission of S.E. is to be obtained before inclusion of this item in the estimate) SSR 2022-23, Item No. 50.30, Sr. No. 1751, Page No. 336, As directed by Engineer-In-Charge.

Providing & fixing G.I. wire Gabions of size 1.00 x 1.00 x 1.00 M coated with Zinc+PVC of required size, section including boxes made of mechanically woven hexagonal shaped wire mesh of type, 10x12cm. edges mechanically selvedged made of heavily (Zinc+ PVC) coated G.I. wires as per BS: 443, mesh wire 3.00 mm Ø edge wire 3.9 mm Ø and filled with 20 to 50 kilogram weight trap stones including conveying with all the leads & lifts and placing at required places in required line, level, slope as per drawing, section as directed etc. complete under tidal conditions. SSR 2022-23, Item No. 49.21 a, Sr. No. 1700, Page No. 324, Rd-19, Page No. 187, Rd-29, Page No.193, Rd-27, Page No. 192 (Except weight of stone specified in wording of specification).

Supplying and spreading Geofabric Filter Layer of Geotextile of Polypropylene multifilament woven to the line, level and grade with pore size less than 0.075 mm and permeability greater than 9.0 litre/sqm/second confirming specification IS:1969 and ASTM standard including conveying to the site, joining and stitching with proper overlap and laying at excavated surface in tidal condition as directed by Engineer- in- Charge etc. complete. SSR 2022-23, Item No. 49.01, Sr. No. 1678, Page No. 320, As directed by Engineer-In-Charge.

Providing and laying a Fibre Glass Geogrid of Tensile strength 50 kN/m manufactured from high quality glass fibre strands and coated with a polymer modified bitumen as reinforcement to Asphalt overlay flexible pavements and Asphalt over distressed rigid P.C.C. SSR 2022-23, Item No. 7.19, Sr. No. 325, Page No. 71, MORTH 702.

Providing and laying a Fibre Glass Geogrid of Tensile strength 100 kN/m manufactured from high quality glass fibre strands and coated with a polymer modified bitumen as reinforcement to Asphalt overlay flexible pavements and Asphalt over distressed rigid P.C.C. SSR 2022-23, Item No. 7.20, Sr. No. 326, Page No. 71, MORTH 702.

Transportation of Material 7 Kilometres. SSR 2022-23, Statement C1 (with machine loading) Page No. 559.

Spreading Hard Murum/ soft murum/ gravel or kankar for side width complete. SSR 2022-23, Item No.2.30, Sr. No. 104, Page No. 25.

Compacting the Hard Murum side widths including laying in layers on each side with vibratory roller including artificial watering complete. SSR 2022-23, Item No. 2.31, Sr. No. 105, Page No. 25.

Providing and laying of uniaxial polyester straps / strips with a protective polymeric coating superior ,high tenacity polyester filament yarn (low creep)

Providing and fixing factory made Hydraulically pressed Mechanically vibrated and compacted precast interlocking cement concrete paving blocks 100mm thick in M-50 grade of approved size and shape for city streets and roads with high volume / heavy traffic as specified and as per IS15658:2006 including cost of all materials, manufacturing, curing, transportation of blocks to work site including loading, unloading and stacking as directed, laying paving blocks in position over bed of natural / crushed sand of 50mm thickness including necessary excavation in all strata, spreading blindge of fine sand over the prepared bed, compacting blocks by plate vibrator etc. complete. SSR 2022-23,Item No. 5.21, Sr. No. 189, Page No. 44, IRC-SP-63.

Supplying erecting testing and commissioning Fabricated panel MRSS 1 MAIN LT PANEL as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following 1 nos of 1600A 4P ACB + 1 nos of 1000A 4P ACB + 1 Nos of 630 Amp TPN MCCB as Incommer & 1 nos of 1600A 4P ACB EDO + 800 FPN MCCB 1 nos + 400 FPN MCCB 1 nos + 200 FPN MCCB 1 nos + 250 FPN MCCB 3 nos + 100 FPN MCCB 2 nos + 63 FPN MCB 9 nos + 32 FPN MCB 5 nos as outgoing refer SLD Panel complying to design as per IS 61439 (Part 1) (Refer : Annexure Sheet A)

Supplying erecting testing and commissioning Fabricated panel LBSS 1 MAIN LT PANEL as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following 2 nos of 1000A 4P ACB EDO + 1 nos of 1250 A 4P ACB EDO as Incommer & + 630 FPN MCCB 3 nos +400 FPN MCCB 2 nos + 100 TPN MCCB 1 nos + 250 FPN MCCB 9 nos + 63 FPN MCB 18 nos + 32 TPN MCB 11 as outgoing refer SLD Panel complying to design as per IS 61439 (Part 1) (Refer : Annexure Sheet B)

Supplying erecting testing and commissioning Fabricated panel LBSS 2 MAIN LT PANEL as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following 2 nos of 1000A 4P ACB EDO as Incommer & 250 TPN MCCB 6 nos + 630A FPN MCCB 2 nos + 250A FPN MCCB 6 nos + 400A FPN MCCB 3 nos + 63A FPN MCB 9 nos + 32A FPN MCB 2 nos + 100A FPN MCCB 2 nos as outgoing refer SLD Panel complying to design as per IS 61439 (Part 1) (Refer : Annexure Sheet C)

Supplying erecting testing and commissioning Fabricated panel LBSS 3 MAIN LT PANEL as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following 1 nos of 1000A 4P ACB EDO + 1 nos of 1000A 4P MCCB as Incommer & 630A FPN MCCB 2 nos + 250A FPN MCCB 5 nos + 100 FPN MCCB 2 nos + 63A FPN MCB 6 nos + 32A FPN MCB 6 nos as outogoing refer SLD Panel complying to design as per IS 61439 (Part 1) (Refer : Annexure Sheet D) .

Supplying erecting testing and commissioning Fabricated panel Typical 350 KVAR as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V, 800 A, and 3 pole 200 A MCCB Outgoing 3 No and 6 No TPMCB 40A to 63A Panel complying to design as per IS 61439 (Part 1) MRSS RTPFC (Refer Annexure E) .

Supplying erecting testing and commissioning Fabricated panel Typical 210 KVAR as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V, 400 A, and 2 No 3 pole 200 A MCCB Outgoing and 7 No TPMCB 40A to 63A, 30 KVAr APFC passive filter panel 9 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure F) .

Supplying erecting testing and commissioning Fabricated panel Typical 23-PLJVB--PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V, 400A, and 250 A Outgoing 1 No and 8 No TPMCB 40A to 63A Panel complying to design as per IS 61439 (Part 1) (Refer Annexure G) .

Supplying erecting testing and commissioning Fabricated panel Typical 26-USLB--PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V, 630 A , and 250 A Outgoing 6 No and 8 No TPMCB 40A to 63A and 32 A TPMCB 2 No and 200 A MCCB 2 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure H) .

Supplying erecting testing and commissioning Fabricated panel Typical 27-LMB-PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V, 250 A , and 100 A Outgoing 1 No and 8 No TPMCB 40A to 63A and 32 A TPMCB 2 No and 200 A MCCB 2 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure I) .

Supplying erecting testing and commissioning Fabricated panel Typical 29-ADB--PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V, 400A, and 200 A Outgoing 1 No and 8 No TPMCB 40A to 63A and 32 A TPMCB 2 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure J) .

Supplying erecting testing and commissioning Fabricated panel Typical 30-PVB PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V, 250 A , and 200 A Outgoing 1 No and 6 No TPMCB 63A and 32 A TPMCB 2 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure K) .

Supplying erecting testing and commissioning Fabricated panel Typical 33-PLB PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V, 200 A , and 63 A Outgoing 5 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure L) .

Supplying erecting testing and commissioning Fabricated panel Typical 37 PMB-PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer g 3 Pole MCCB 415V, 630A, and 400 A Outgoing 1 No and 250 A Outgoing 1 No 63 A Outgoing 15 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure M) .

Supplying erecting testing and commissioning Fabricated panel Typical 41 SSB-PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer g 3 Pole MCCB 415V, 630A, and 400 A Outgoing 1 No and 32 A Outgoing 4 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure N) .

Supplying erecting testing and commissioning 43 FOF-PDB Fabricated panel Typica as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer g 3 Pole MCCB 415V, 630A, and 250 A Outgoing 1 No and 200 A Outgoing 1 No 32 A MCB 4 No Panel complying to design as per IS 61439 (Part 1) (Refer Annexure O) .

Supplying erecting testing and commissioning 50 ADK-PDB Fabricated panel Typica as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer g 3 Pole MCCB 415V, 400 A and 400 A Outgoing 1 No and 2 No 32 A MCB Panel complying to design as per IS 61439 (Part 1) (Refer Annexure P) .

Supplying erecting testing and commissioning 52 SPDR PDB Fabricated panel Typica as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer g 3 Pole Air Circuit Breaker 415V, 1600 A and 630 A Outgoing 1 No and i number 250 A and 200 A MCCB and 9 No 63 A ougoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure Q) .

Supplying erecting testing and commissioning 53-MAG PDB Fabricated panel Typica as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer and Outgoing of 250 A ,1 No and i number 250 A and 200 A MCCB and 1 No 63 A ougoing and 4 No 32 A Outgoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure R) .

Supplying erecting testing and commissioning 57-KLB PDB Fabricated panel Typica as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer and Outgoing of 250 A each ,1 No and i number 250 A and 200 A MCCB and 4 No 63 A ougoing and 2 No 32 A Outgoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure S) .

Supplying erecting testing and commissioning HPS-5-6 WATER PUMP PANEL Fabricated panel Typica as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer of 200 A MCCB 1 No , 2 No 63 A MCB ougoing and 1 No 32 A MCB Outgoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure T) .

Supplying erecting testing and commissioning Fabricated panel Typica 59 DDB PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer of 250 A MCCB ,1 No , 3 No 63 A MCB ougoing and 2 No 32 A MCB Outgoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure U) .

Supplying erecting testing and commissioning Fabricated panel Typical 66 BOH-PDB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer of 400 A MCCB ,No 200 A MCCB ougoing and 3 No 63 A MCB Outgoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure V) .

Supplying erecting testing and commissioning Fabricated panel Typical 37 PMB HVAC DB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following 1 No Incomer of 630 A MCCB, 200 A MCCB ougoing 19 No 63 A MCB Outgoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure W) .

Supplying erecting testing and commissioning Fabricated panel Typical 41 SSB HVAC DB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following 1 No Incomer of 630 A MCCB, 200 A MCCB ougoing 19 No 63 A MCB Outgoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure X) .

Supplying erecting testing and commissioning Fabricated panel Typical 52 SPDR HVAC DB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following 1 No Incomer of 630 A MCCB, 200 A MCCB ougoing 19 No 63 A MCB Outgoing Panel complying to design as per IS 61439 (Part 1) (Refer Annexure Y) .

Supplying erecting testing and commissioning Fabricated panel Typical 26-USLB-EVENT DB as per SLD made of 14 SWG MS Sheet IP 42 rated duly powder coated with comprising of the following Incomer 3 Pole MCCB 415V,630 A , and 8 No 3 pole 200 A MCCB Outgoing and 6 No TPMCB 40A to 63A Panel complying to design as per IS 61439 (Part 1) (Refer Annexure Z) .

SITC of Trafo MIMIC -4 x 3 window, 230 V AC single Ph 50 Hz input, with luminous facia, lables for faults/ alarms, panel door mounted, with acnowledge, accept and reset push buttons, inbuilt sounder, silence PB, test PB, Rs 485 port complete with assembly and internal wiring with terminals

SITC of Auxiliary Relays, 5 pin, 2 changover, 5 A contact rating suitable for 230 V AC, NO/NC pair, including Base for pin mount relays, prewired, with terminal identification

SITC of standalone Auto- Mains- failure (AMF) Controller , to be mounted on panel door, with programmable timer, sensing of input, 3 channel putputs, potential free, 5 A contact rating, suitable for 230 V AC 50 Hz

Providing & erecting floor/wall mounting, MCCB panel board, with door, suitable for four pole incoming 250A, 6 ways four pole outgoing, up to 100 A MCCBs on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCBs) (CSR NO - 5-7-3)

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (36 poles) or TP MCB of 12 ways (36 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/ (CSR 5-4-17 )

Supplying & erecting triple pole and neutral distribution board (TPNDB), 3 pole/4 pole MCCB as incomer & outgoing SP MCB (24 poles) or TP MCB of 8 ways (24 poles), with door, 1.2mm thickness, surface/flush mounted, on iron/GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB1 (CSR 5-4-16 )

Supplying & erecting triple pole and neutral distribution board (TPNDB), SPMCB of 4 ways/phase (12 poles), with door, 1.2mm thickness, surface/flush mounted, IP 43 protection on iron/GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB (CSR 5-4-1 )

Providing & erecting 3 Pole MCCB 415V, 200A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in providedenclosure/panel as per specification no. SW-SWR/MCCB ( CSR NO - 5-5-2)

Providing & erecting 3 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB (CSR 5-5-3)

Providing & erecting 3 Pole MCCB, 415 V, 100A, rated short-circuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SW-SWR/MCCB ( CSR NO - 5-5-1)

Supplying, erecting & marking TPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB ( CSR NO - 5-3-11)

Supplying, erecting & marking TPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB ( CSR NO - 5-3-10)

Supplying, erecting & marking SPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB ( CSR NO - 5-3-4)

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB ( CSR NO - 5-3-3)

Supplying, erecting & commissioning 4 pole RCCB 63A, electromagnetic type with 30/100/300 mA sensitivity with earth leakage trip indication complete as per specification no. SW-RCCB/RCCB (CSR NO - 5-6-6)

Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO (CSR NO - 5-6-10)

Supplying, fixing and commissioning 2 pole, RCBO 6/10/16/20/25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO (CSR NO - 5-6-9)

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB (CSR NO - 5-3-2)

Supplying, erecting, testing and commissioning of 5 kVA capacity online pure sine wave with backup time of 0.5 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, single phase input & 1 phase output complete with all protections as per specification no. AP-UPS (CSR No - 3-7-4)

Supplying, erecting, testing and commissioning of 10kVA capacity online pure sine wave, with backup time of 0.5 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input & 3 phase output complete with all protections as per specification no. AP-UPS (CSR No - 3-7-7)

Supplying, erecting, testing and commissioning of 20kVA capacity online pure sine wave, with backup time of 0.5 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input and 3 phase output complete with all protections as per specification no. AP-UPS (CSR No - 3-7-8 ( New))

Supplying, erecting, testing and commissioning of 50 kVA capacity online pure sine wave, with backup time of 0.5 hrs. PWM & IGBT based UPS with 0.9 to unity output pf, 3 phase input and 3 phase output complete with all protections as per specification no. AP-UPS

Supplying and erecting 12 V/65Ah SMF battery with battery terminal wire, duly charged complete with 24 months warranty complete (CSR No - 3-8-11)

Supplying and erecting 12V/100Ah SMF battery with battery terminal wire, duly charged with 24 months warranty complete. (CSR No - 3-8-12)

Supplying and erecting integrated LED Highbay Fitting 100 W IP65 & IK08 class having die cast aluminium housing with polycarbonate diffuser with integrated optics, having system lumens output of Min. 15000 Lumens, min. efficacy of 145 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L50B50 , including driver complete with 3 Year warranty as per specification No FG-ODF/FLS2. HL - Highbay Light (CSR No - 2-6-2)

Supplying & erecting inverter LED batten 20 W tube light fitting with polycarbonate housing, heat sink, integrated HF electronic driver, Min. 2600 mAh Lithium ion Battery with charging time of 8-10 Hours and backup time of Min. 3 hrs. with minimum 25% of initial Watts having luminous efficacy of 100 lumen/watt, CRI>80, CCT of 6500K and THD<=20% having useful life of minimum 25000 hrs. with overheating protection with 2 years warranty (CSR No - 2-1-22)

Supplying and erecting LED square / circular Max. 18 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty (CSR No - 2-1-5)

SITC decorative chandlier having antique view Height: 115 cms Diameter: tapered uniformly to 100 cms. Weight: 75 kg.MOC - Blow Glass, Suspension chain - Brass - Length 800 mm with Eye bolt/ hook,8 x 40 W LED, Lumen output of minimum 25600 Lumens, Min efficiency of 80 lumen/W operating range of 120- 270 V direct bulbs, Input Frequency - 50 Hz, CRI>80, CCT upto 5000K, Beam Angle of 90 deg., max. ripple of 5%,THD<10%, p.f. >0.95, surge protection of 2.5 kV,Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement Supporting Rim - plated/ anodised MS - 100 cm Dia, complete with accessories complete with 3 years warranty. CL - Chandlier

SITC wall mounted decorative 2X 20 w LED Up Down light (cylindrical) with aluminium housing, beam adjustable reflector, approx cylinder dia 130 mm, offers uniform light distribution with IP65 protection suitable for wall mount application. Lumen output of minimum 4400 Lumens, Min efficiency of 110 lumen/W CRI>80, Input Frequency - 50 Hz CCT upto 5000K, max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty UDL - Up Down light

SITC erecting wall mounted decorative 1X 20 w LED Up Down light (cylindrical) with aluminium housing, beam adjustable reflector, approx cylinder dia 130 mm, offers uniform light distribution with IP65 protection suitable for wall mount application Lumen output of minimum 2200 Lumens, Min efficiency of 110 lumen/W CRI>80, Input Frequency - 50 Hz,CCT upto 5000K, max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty UDL - Up light

Supplying and erecting LED Strip light 5m Length Max. 95 W IP20 class having minimum lumens output of 1600 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50 including driver with 1 year warranty. (CSR no - 2-1-11)

SITC of ornamental wall bracket, made of wrought iron of approximate size of 600 mm x 300 mm with a holding shacle for light fitting, with natural french antic polish Suitable for operating voltage 230V (Refer conceptual drawing No ML-LE-53)

SITC of ornamental wall bracket, made of pine wood log of approximate size of 400 mm x 500 mm with a holding shackle for light fitting, with wiring fullthough etc complete with backodised antic polish. Suitable for operating voltage 230V (Refer conceptual drawing No ML-LE-53)

SITC of ornamental wall bracket, made of cast iron approximate size of 400 mm x 400 mm with a holding shacle for light fitting, with wiring fullthough etc complete with backodised antic polish. Suitable for operating voltage 230V (Refer conceptual drawing No ML-LE-53)

SITC of ornamental hanging bracket, made of jute ropes and MS rings ( 3 nos) to be suspended from true slab / ceiling by hanging size of 800 mm Diameter 650 mm,etc complete with necessary onning & acccessories.Suitable for operating voltage 230V (Refer conceptual drawing No ML-LE-53)

SITC of wall projector light fittings, LED 10 W , colour temp 3000 Deg K, Beam angle 20 Deg. MacAdam ellipse < 2/3; MOC Aluminium Die cast housing, powder coated, with external 24 V DC LED driver, CRI >90 , max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement customised mounting bracket complete with fixing accessories etc with 3 years warranty.Equivalent to AFTER 7 AFMA-8302010-DN-H,

SITC of true ceiling surface downlighter, round made up of Die cast Aluminium, with matt reflector, Lens optics, LED, 36 W, system lumens output of Min. 3960 Lumens, min. efficacy of 110 lumen/W, Beam angle 30 deg,Temp 4000 K, UGR < 19,CRI>80,Input Frequency - 50 Hz, max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement acessories complete with 3 years warranty, Equivalent to - TAKEO T150C, TMC 1-8276018F- BM

SITC of true ceiling suspended / surface downlighter, round made up of round polycarbonate, with matt PC diffuser, LED, 24 W, system lumens output of Min, 2640 Lumens, min. efficacy of 110 lumen/W, Beam angle 120 deg Temp 4000 Deg K, UGR < 26, CRI>80, max. ripple of 5%,THD<10%, p.f. >0.95, operating range of 120-270V,Input Frequency - 50 Hz, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with acessories complete with 3 years warranty, Equivalent to - MINT 280 MASM-8S3A224S-WN

SITC of ceiling Gimble spots, with 3 nos of adjustable focus LED,3 x 10 W each having ,Al die cast housing system lumens output of Min. 3300 Lumens, min. efficacy of 110 lumen/W, CRI>80,Input Frequency - 50 Hz, CCT upto 3000K, Beam Angle of 30 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with acessories complete with 3 years warranty., Equiv to Nymane

SITC of ceiling Gimble spots, with 4 nos of adjustable focus LED,4 x 10 W each having ,Al die cast housing system lumens output of Min. 4400 Lumens, min. efficacy of 110 lumen/W, CRI>80, Input Frequency - 50 Hz, CCT upto 3000K, Beam Angle of 30 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with acessories complete with 3 years warranty., Equiv to Nymane

SITC of ceiling Gimble spots, with 2 nos of adjustable focus LED,2 x 10 W each having ,Al die cast housing system lumens output of Min. 2200 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 3000K, Input Frequency - 50 Hz, Beam Angle of 30 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with acessories complete with 3 years warranty., Equiv to Nymane

SITC of Linear ascent light module profile LED 13 W ,system lumens output of Min. 1430 Lumens, min. efficacy of 110 lumen/W CRI>80,Input Frequency - 50 Hz, CCT upto 4000K, Beam Angle of 30 deg.UGR <19, max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including LED,6 nos/Mtr (inserts) integral driver having mounting arrangement suspended from true slab/ ceiling, Extruded Aluminum profile 1 mtr standard length fitting. ,warranty 3 years, Equiv to Fusion Linear- FL-AL300-13W-840-30D

SITC Of DECORATIVE WALL,MOON LIGHT, CIRCULAR wall mount 22 W,LED,MOC Die cast Aluminium with integral driver having IP 65 system lumens output of Min. 2420 Lumens, min. efficacy of 110 lumen/W CRI>80,Input Frequency - 50 Hz CCT upto 3000K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, having mounting arrangement with acessories complete with 3 years warranty, Equivalent to -CLIFTON Cat CLIF-830A125F-DN

SITC of walkover embedded up light , LED 5 W, Die cast Lauminium housing, top cover SS, system lumens output of Min. 550 Lumens, min. efficacy of 110 lumen/W CRI>80,Input Frequency - 50 Hz, CCT upto 5000K, Beam Angle of 45 deg. Lens optics for glare reduction max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, Including external 24 V DC LED driver, IP 67, having mounting arrangement with acessories complete with 3 years warranty. Equiv to TERARACE, TEMI-8304506F-DN

Supplying and erecting IP65 and IK08 rated UV shielded polycarbonate waterproof and dustproof industrial grade LED fitting (4 feet) max. 36W with high transitivity diffuser with system lumens output of min. 4300 lumens , min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50 , IP20 rated, including driver with auto cutoff & auto restart feature at 325V with end caps on PVC Block/wooden board with 3 years warranty ( CSR NO - 2-2-1)

Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% with IR remote control/compatible speed regulator, Temperature Rise of Max. 40 deg. C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF (CSR no - 2-10-22 (New))

Supplying and erecting fan hook box of 10 mm M.S. round bar bounded to the R.C.C. bars upto 50 mm length each side and pierced through a 16 S.W.G. thick aluminium/M.S. Bowl 100 mm dia. or equivalent square size and having depth upto 75 mm complete erected with duly painted by one coat of red oxide paint and two coats of paint erected in position and without any leakage of slurry of cement concrete on either side of the box and positioned to the bottom level of the slab. (CSR NO- 2-11-5)

Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire. (CSR NO- 2-11-6)

Point wiring for ceiling fan (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WG-PW/HW (Avg. Length 15 Mtr.) (CSR NO- 1-7-16 New)

Point wiring for ceiling fan concealed type in min 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WGPW/ CW (Avg. Length 15 Mtr.) (CSR NO- 1-7-6 New)

Point wiring for light/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FRLSH grade copper wires, modular type switch, earthing and required accessories as per specification No: WGPW/ HW (Avg. Length 15 Mtr.) (CSR NO- 1-7-15 )

Point wiring for light/bell/exhaust fan in 20 mm FRLS grade HMS PVC conduit with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG_0002_PW/SW. (Avg. Length 15 Mtr.) (CSR NO- 1-7-12) ( Primary light point)

Secondary point wiring for additional light/ bell point, concealed type in min 20 mm FRLS grade PVC conduit with 1.5 sq.mm. (2+1E) FRLSH grade copper wires with required accessories as per specification No: WG PW/CW (CSR NO- 1-7-22)

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WG_0002_PW/CW (CSR NO- 1-7-26)

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. (CSR NO- 1-1-9)

Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC. (CSR NO- 1-1-10)

Supplying and erecting HMS PVC conduit FRLS grade 32 mm dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. (CSR NO- 1-1-11)

Supplying and laying HMS PVC conduit FRLS grade 32mm dia. With necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC. (CSR NO- 1-1-12)

Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit (CSR NO- 1-2-2 New)

Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW (CSR No - 1-3-2)

Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW (CSR No - 1-3-2) 1/2

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW (CSR No - 1-3-3) 1/2

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW (CSR No - 1-3-3)

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete (CSR No - 1-6-1)

Supplying and erecting modular type switch 16A duly erected on provided plate and box with wiring connections complete. (CSR No - 1-6-2)

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete (CSR No - 1-6-10)

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete. (CSR No - 1-6-11)

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module duly erected. (CSR No - 1-6-28)

Supplying and erecting PVC Surface modular switch box with double mounting plate for 6 module duly erected. (CSR No - 1-6-30)

Supplying and erecting PVC Surface modular switch box with double mounting plate for 12 module duly erected. (CSR No - 1-6-32)

SITC of Exit Signages with 1 x 3 W LED. with Single / double sided & hanging arrangement. With Battery Backup. Exit Signages: A range of large exit signs for 32m, 48m or 60m viewing distances with Lithium-Ion (LIION) battery technology. Designed for ceiling installations. Electronics designed to lengthen the life of the battery, minimizing maintenance costs, as well as an environmentally friendly battery Complete as required.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 400 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 75 mm width & 50 mm height complete with necessary coupler plates & hardware in approved manner

Providing & Fixing in position, MS fabrication work using angles, sqr tubes, c channels etc for various partition frame as per Design & Instructions & Complete in all aspects . including all materials labour,finishing etc complete

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR no - 7-1-24)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½core 240 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR no - 7-1-23)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR no - 7-1-20)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR no - 7-1-19)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR no - 7-1-18)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR no - 7-1-17)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR no - 7-1-16)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR no - 7-1-15)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR no - 7-2-34)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR no - 7-2-33)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR no - 7-2-32)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR no - 7-2-31)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR no - 7-2-15)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR no - 7-2-16)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR no - 7-2-17)

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP. (CSR NO- 9-2-8)

Supplying erecting testing and commissioning cubicle pattern Vehicle charging DB for Cars & Bus as per SLD made of 14 SWG MS Sheet IP 65 rated duly painted with 2 coats of enamel paint comprising of the following Incommer 630A TPNE MCCB of as Incommer & 8 Each of 63 A TPN MCB + 1 of 250A TP MCB as outgoing Vehicle Charging DB (Bus + Car) Panel complying to design as per IS/IEC 61439 Hirkani 1 (Refere Annex AA)

Supplying erecting testing and commissioning cubicle pattern Vehicle charging DB for Cars & Bus as per SLD made of 14 SWG MS Sheet IP 65 rated duly painted with 2 coats of enamel paint comprising of the following Incommer 630A TPNE MCCB of as Incommer & 7 Each of 63 A TP MCB + 10 each of 32A TP MCB as outgoing Vehicle Charging DB (Car+Bike) Panel complying to design as per IS/IEC 61439 Hirkani 2 (Refere Annex AB)

Supplying and erecting Clear post top and Top Mounting LED Lantern - 70 W fitting , ALuminium Di cast Housing with Acrylic Diffusers Top mount lantern , Luminous flux - 5050 lm, Luminaire efficacy - 70 lm/W, CRI>70, CCT upto 5000K, THD<10%, p.f. >0.95, Input Voltage - 150V to 270V AC, Input Frequency - 50 Hz, Ingress Protection - IP65 & IK08 Class, surge protection of 10 kV,Life class of 50,000 Hrs.at L70B50 3 years warranty Tag : TF - Clear post top and Top Mounting LED Lantern - 70 W to 90 wt fitting

Supply & Installation of 7 mt long single arm decorative lamp post made of Iron Pole with cast iron on bracket arms & made of FRP to be installed on the pole top & lit up with 3Wt LED spot light from both sides of the symbol. The Cast Iron components should be made from FG220 Grade as per IS210/1993 with BHN160-220. .The pole is provided with 3 Each. A door is provided with anchorage and wiring accessories. The colour of lamp is Antique copper. Material used in poles as cast iron parts with Bottom dia of 300 mm & top section dia of 60 mm with bracket arm of 48 mm OD. Bracket arm should be 900 mm wide on Single side from the centre of the pole. Bottom of pole is rectangle shape and top or other is circular shape of pole. The product is an all-weather proof & Maintenance free Lamp post consist of access door to manage wiring & accessories. . All sections shall be free from defects like blow holes, porosity, hard spots, cracks, hot tears, cold shuts, distortion, sand and slag inclusion and other harmful defects. Accuracy of machined parts should be maintained through out. Each and every cast piece should be subject to shot blasting to remove all its external dirt and residues etc. Entire unit should be given an extensive three stage treatment with PU based etch primer and paint prescribed for such surfaces to make it absolutely rust and corrosion proof, as well as giving it a pleasing appearance & shall be in Antique finish. A minimum of 60 microns of coating thickness should be achieved on the final piece. All the grooves and carvings of the pole unit should be free from any kind of distortion for a pleasing aesthetic Appearance. Pole unit having base of size 410x410 with PCD 505 mm should be grouted using 4 nos. J-Type of hot dip galvanized type Anchor bolts of size 20x750 mm long .The Lamp Post should be designed to hang 1 no of 70 Wt to 90 Wt decorative hanging Lantern. Tag : TF - Clear post top LED Lantern Fixture Mounted Pole

Supply & Installation of 7 mt long double arm decorative lamp post made of Cast Iron Pole with cast iron on bracket arms &Rajmudr logo made FRP to be installed on the pole top & lit up with 3Wt LED spot light from both sides of the symbol. The Cast Iron components should be made from FG220 Grade as per IS210/1993.The pole is provided with 3 Each. A door is provided with anchorage and wiring accessories. The colour of lamp is Antique copper. Material used in poles as cast iron parts with Bottom dia of 300 mm & top section dia of 60 mm with bracket arm of 48 mm OD. Bracket arm should be 900 mm wide on each side from the centre of the pole. Bottom of pole is rectangle shape and top or other is circular shape of pole. The product is an all-weather proof & Maintenance free Lamp post consist of access door to manage wiring & accessories. All sections shall be free from defects like blow holes, porosity, hard spots, cracks, hot tears, cold shuts, distortion, sand and slag inclusion and other harmful defects. Accuracy of all machined parts should be maintained through out. Each and every cast piece should be subject to shot blasting to remove all its external dirt and residues etc. Entire unit should be given an extensive three stage treatment with PU based etch primer and paint prescribed for such surfaces to make it absolutely rust and corrosion proof, as well as giving it a pleasing appearance & shall be in Antique finish. A minimum of 60 microns of coating thickness should be achieved on the final piece. All the grooves and carvings of the pole unit should be free from any kind of distortion for a pleasing aesthetic Appearance. Pole unit having base of size 410x410 with PCD 505 mm should be grouted using 4 nos. J-Type of hot dip galvanized type Anchor bolts of size 20x750 mm long . The Lamp Post should be designed to hang 2 nos of 70 Wt to 90 Wt decorative hanging Lanterns. Tag : TF - Clear post top LED Lantern Fixture Mounted Pole

Earthing for Street light poles - Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP (CSR 9-1-4)

Supplying and erecting Clear post top and Top Mounting LED Lantern - 45 W fitting (BLS BOR 45W WW CL TM) Relaxed white well-lit, with reduced glare having opal PC diffuser,, PDC Heat sink on Top Extruded aluminum body in grey powder coated, Luminaire is wired with in‐built driver, Constant current electronic driver provided with high voltage, open & short circuit protection, Luminous flux - 4500 lm, Luminaire efficacy - 100 lm/W, Input Voltage - 140V to 270V AC,CRI>70,THD <10%,p.f. >0.95,CCT upto 6500K Input Frequency - 50 Hz, Ingress Protection - IP65 & IK08 Class operating range of 140-260V, in built surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50 with 3 years warranty. Tag :BF-Gate Light - Opal post top and Top Mounting LED Lantern - 45 W fitting

Supplying and erecting integrated LED Bollard Cylindrical/Cubical shaped 800mm 8W IP65 & IK10 class having extrusion aluminium housing with polycarbonate diffuser, having system lumens output of Min. 800 Lumens, min. efficacy of 100 lumen/W, CRI>80, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 2 kV, Life class of 25,000 Hrs. at L50B50, including driver complete with 2 Year warranty as per specification No FG-ODF/FLS2. Tag : BL - Bollard Light (CSR No - 2-4-20)

Supplying and erecting integrated LED flood light fitting Max. 195W IP65 & IK07 class having pressure die-cast aluminium housing, having system lumens output of Min. 23400 Lumens, min. efficacy of 120 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-270V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50, including driver with U shaped bracket with 3 Years warranty as per specification No FG-ODF/FLS2. Tag : HM - Flood Light (CSR no -2-4-18) (Parking + 13 PT)

Supplying and erecting 16 m (clear height) motorized high-mast (Top-150mm,Bottom- 360mm) hot dipped galvanized material with average minimum thickness 65 micron, made from high tensile structure grade steel as per BSEN -10025 S 355/E350 & 3 mm thickness, with base plate 25 mm thick x OD 520 mm grade as per IS-2062, pole made in single section & submerge arc welded, with lowering & raising motorized unit, wire rope stainless steel 316 grade 2 Each., 7x19 construction 5mm, SG-DG U clamps, double drum winch assembly 350 kg, 5x2.5 sq.mm flexible copper cable with lantern carriage assembly suitable for max. 12 Each.luminaires and its control gear box, lightning arrestor, arrangement for fixingaviation light, high-mast with serial number, factory inspection report/test report of high-mast should be provided as per specifications on provided foundation J type stud/bolts with necessary accessories complete. specification no. OHPL/ HM (excluding luminaries) Pole For above Light (CSR no - 8-2-2)

Supply and erecting 9m (clear height) Fixed type high-mast (Top-100mm,Bottom- 200mm) with hexagonal /round bracket and foundation bolts suitable for max. 4 nos. flood light fixtures on provided foundation as per specification no.OH-PL/OPL (excluding luminaires). (CSR no - 8-2-8)

SITC Building focus lights with different beam angles & multiple lumens output. 150W power, 6 LEDs/fixture,system lumens output of min. 15000 lumens, min. efficacy of 100 lumen/W, CRI>70, CCT upto 5000K CC or DMX512 control.IP66 Protection, with powder coated grey color housing.Frequency 50/60 Hz, operating range of 140-260V, in built surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK08 Class rated on provided PVC Block / wooden board Control Mode: CC/DMX512,Installation Pipe Diameter: Ø 8.5 x 60 mm, Temperature of Working Condition: -30⁰~50⁰C, with 3 years warranty. Tag : SFL - Special Focused Light - 150 W fitting

SITC Underwater Lights 50 W (IP68) high power colour changing with any colour Pressure Die cast, Stainless Steel grade SS 316L grade front cover and housing 7’’ diameter round type wall mount LED Bulb,12 V DC. Protection class IP68 suitable for fountain of different colours.system lumens output of min. 5500 lumens, min. efficacy of 110 Lumen/W, CRI>70, CCT upto 4000K, Beam Angle of 70 deg., THD<10%, p.f. >0.95, operating range of 230-12 V DC Including external driver in built surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, IK08 Class rated, IP68, PG - 11 CU with NICKEL - coated cable gland, EPDM gasket, Built in over heat sensor system inabling automatic shutdown at 75 deg. with 3 years warranty.equivalent to LHENBNPSU49I035 Tag : WIL - Underwater Lights (Marinashine Maxi) - 50 W fitting

Supplying and erecting LED Strip light 5m Length Max. 95 W IP20 class having minimum lumens output of 1600 Lumens/m, min. efficacy of 90 lumen/W, CRI>80, CCT upto 5000K, Beam Angle of 110 deg., THD<10%, p.f. >0.95, operating range of 230-270V, Life class of 30,000 Hrs. at L70B50 including driver with 1 year warranty. Tag : STRL - LED Strip - 95 W / mtr (CSR No : 2-1-11)

Supplying and erecting IP65 and IK08 rated UV shielded polycarbonate waterproof and dustproof industrial grade LED fitting (4 feet) max. 36W with high transitivity diffuser with system lumens output of min. 4300 lumens , min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 4 kV, Life class of 50,000 Hrs. at L70B50 , IP20 rated, including driver with auto cutoff & auto restart feature at 325V with end caps on PVC Block/wooden board with 3 years warranty. (CSR : 2-2-1) Tag : TL - Tube Light - 36 W fitting

SITC of Integrated flood light outdoor type (RGBW) , Main material used is high strength aluminium die casting material, IP 65 surface anti-ageing electrostatic spray processing,super resistance to corrosiont,Toughened glass cover, High strength impact resistance.Configurable white or monochromatic RGB, Lighting effects with gorgeous color purity and powerful change.Voltage of AC100-277V with beam angle is 25°x60°Of 3980 Lumen , RGB colour , CRI>80,THD<10%, p.f. >0.95, in built surge protection of 10 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated . 6 Kg net weight, 3 years warranty, Equivalent to LHEPBNUSP47J113 with 3 years warranty. Tag : FCDL - Facade light (Ranger Maxi)- 110 W fitting

SITC of 27 W Color changing & monochromatic Buried Uplighter ideal for uplighting facades, columns & features with multiple Optics & extensive pallet of colors.Luminaire body uses high pressure die-casting aluminium. Coveruses stainless steel while the buried barrel uses high-quality corrosion resist antnylon. The diffuser use thickened toughened glass, having an advantages inimpact resistance and abrasion. the diffuser and light cover is at the samelevel, no fall. monochrome or RGB color It’s carried out by the DMX512 system Humanized design, fit for a wide range of demand in variouspplications temperature ofthe cover is low, High strength toughened glass, can withstand a weight of 3400 KG.system lumens output of min. 2970 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated with 3 years warranty..Equivalent to LHEOGCPSU48V027 Tag :WSL - Engross MaxiRGB/Mono- - 31W

Making cement concrete foundation in 1:2:4 cement concrete with foundation bolts and nuts complete. (cost of wooden box is included) (for pumps). (CSR No - 16-3-5)

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole). (CSR No - 16-3-9)

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 9m & 10m high octagonal /conical GI pole). (CSR No - 16-3-1)

Making M- 20 cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq. m at 2 m depth including excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 16 m raising lowering high mast). (CSR No - 16-3-13)

Supplying and laying HMS PVC conduit FRLS grade 25 mm dia with necessary accessories in RCC work/false ceiling/false flooring as per specification No. WG-MA/CC. (CSR no - 1-1-10)

Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV (CSR no - 1-3-14)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-24)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½core 240 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-23)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-22)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-20)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-19)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 70 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-18)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-17)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 35 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-31)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-30)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-29)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL ( CSR No - 7-1-28)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR No - 7-1-15)

Supplying & erecting cast iron cable indicator plate buried along with route of cable for PVC / XLPE armoured cable as per specification No. CB-CIP (CSR No - 7-8-1)

Supplying, erecting & commissioning 20 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW (CSR No - 1-9-12)

Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 250 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete. (CSR No : 7-6-7)

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. (CSR No : 7-6-10)

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. (CSR No : 7-6-9 )

Supplying, erecting, testing and commissioning of 10kW, 3 x 3.3 KW AC Electric Vehicle charger (suitable for 2/3/4 wheeler) having minimum IK08/IP 54 Protection suitable for three phase, 415V AC, 50Hz incoming and 3 Each. output as per IEC 60309 industrial sockets having capacity of output current of 16A 240V AC at each socket with 3.5"TFT touch screen for human interface & LED Light for status indication and metering for measurement of consumed energy having metering accuracy +/-1%, one hour battery backup for communication, emergency push stop button and having short circuit, over & under voltage, overload, over temperature, earth leakage protection and enclosure made of minimum 1.5mm duly RAL7035 Coated M.S, Erected on iron/GI frame on provided cement concrete foundation complete with one year on site warranty, confirming to IS 17017 Series as per specification (CSR No - 4-7-1)

Supply, Installation, Testing and Commissioning 7.2 kW AC Electric Vehicle charger (suitable for 4 wheeler) having minimum IK08 & IP54 protection suitable for single phase, 230V AC, 50Hz, incoming and 1 nos. output having capacity of output current of 32A at 230V with Type two connector as per IEC 62196-2 , Interlocking arrangement & minimum 5 meter charging cable length, 3.5" TFT screen for human interface & LED light for status indication and metering for measurement of consumed energy having metering accuracy +/- 1%, one hour battery backup for server communication, emergency push stop button, with user interface by mobile application/QR Code/RIFD Card/Password Login and having short circuit, over & under voltage, overload, earth leakage ,Over temperature, surge protection and enclosure made of minimum 1.5mm duly RAL7035 coated M.S, erected on iron/GI frame on provided cement concrete foundation complete with one year on site warranty, confirming to IS 17017 Series as per specification (CSR No - 4-7-2)

Supplying, erecting, testing and commissioning of 30 kW DC ElectricVehicle Charger (suitable for 4 wheeler) having minimum IK08 & IP 54 Protection suitable for three phase, 415V AC, 50Hz incoming supply and 1 nos 30kW output charger interface CCS2 with 200-500VDC supply, Interlocking arrangement with minimum 4 meter charging cable length, 5" LCD Touch Screen for human interface & LED Light for status indication and metering for measurement of consumed energy having metering accuracy +/-1%, One hour battery backup for communication, emergency push stop button. User interface by mobile application/QR Code/RIFD Card/Password Login with payment options and having short circuit, over & under voltage, input phase reversal, surge protection, earth leakage protection and enclosure made of minimum 1.5mm duly RAL7035 coated M.S, erected on iron/GI frame on provided cement concrete foundation complete with one year on site warranty, confirming to IS 17017 Series as per specification (CSR No - 4-7-4)

Providing yearly subscription of payment gateway option for AC/DC EV Charger CMS (Charger management software) system for billing and payment gateway along with mobile application /android/IOS base app to facilitate charging, CMS should have ISO/IEC 27001:2003 certification (CSR No - 4-7-5)

Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC (CSR NO 1-10-1)

Supplying and installing cat-6 cable with rodent proof and anti termite jacket suitable for networking as per specification No. WG-COC/NC (CSR NO -1-10-6)

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP (CSR.NO 1-12-4)

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO (CSR.NO 1-12-2)

Supplying and erecting PVC Surface modular switch box with double mounting plate for 3 module duly erected. (CSR.NO 1-6-28)

Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 2 module duly erected flush to wall with required chiselling and finishing with cement mortar / POP as per required to match the background (CSR.NO 1-6-35)

Supplying and fixing 1 m length, UTP patch cord of enhanced Cat 6 type with 4-connector channel, performance test report as per ANSI/TIA-568.2-D in position as per specification No. WG-COC/PC (CSR.NO 1-10-17 (New))

Supplying and fixing 3 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC (CSR.NO 1-10-19)

Supplying and installing, testing & commissioning of digital (hybrid) type EPABX of 6 x 32 extensions suitable upto 96 extensions complete (CSR.NO 1-9-26 + Note 1 X 4 Time)

Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW (CSR.NO 1-9-1)

Supplying, erecting & commissioning MDF Box 200x200 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW (CSR.NO 1-9-4)

Supplying & erecting 100 pair, 0.5 mm dia. jelly filled armoured telephone copper cable with poly-al laminate moisture barrier, polythene sheathed, G.S.Tape armoured polythene jacketed having laid in provided trench as per specification No. WG-TW (CSR.NO 1-8-16)

Supplying & erecting 20 pair, 0.5 mm dia. jelly filled armoured telephone copper cable with poly-al laminate moisture barrier, polythene sheathed, G.S.Tape armoured polythene jacketed having laid in provided trench as per specification No. WG-TW (CSR.NO 1-8-14)

Supplying & erecting 2 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/conduit as per specification No. WG-TW (CSR.NO 1-8-1)

Supplying & erecting rosette box RJ type Bakelite box on wall with LED indication duly connected as per specification no. WG-TW (CSR.NO 1-9-20)

Supplying & erecting 0.5 mm dia, copper jumper wire as per specification No. WG-TW (CSR.NO 1-8-17)

Supplying, installing, testing & commissioning IP telephone instrument as per specification complete. (CSR.NO 1-8-30)

Supplying, installing, testing & commissioning push button telephone instrument desk top/wall mount with caller ID & Speaker unit as per specification complete (CSR.NO 1-9-29)

Supplying and erecting broadband splitter unit with 1 input & 2 output RJ 11 female connectors complete (CSR.NO 1-9-21)

Supplying and erecting LSZH armoured multimode optical fibre cable with 6 fibres, core dia 50/125 µm (OM3), suitable upto 10 GBPS, ethernet distance at 850 nm of wavelength, on wall/ceiling or laid in provided pipe/trench as per specification no. WG-COC/OFC LSZH (CSR.NO 1-10-8)

Supplying and fixing 12 ports light guide unloaded interconnect unit, wall mounted type, with adapter panel for termination of optical fibre cables on wall in provided U rack complete as per specification no. WG-NAS/ LIU (CSR.NO 1-12-6)

Supplying and fixing SC/LC type multimode pigtails (OM4) as per specification complete. WG-NAS/LIU2 (CSR.NO 1-12-14)

Supplying and plugging 3 m fibre patch cord LC-LC MM (50) OM3 LSZH duplex complete as per specification no. WG-COC/FPC (CSR.NO 1-10-24)

Supplying and fixing multimode pigtails with SC/SC type splicing for (OM4) complete. (CSR.NO 1-10-28 (New))

Supplying, fixing, and configuring 24 ports + 4 (SFP+) port, Managed Layer 2, POE Switch of , 370W, 6KV surge protection on ethernet port and console port for management erected in provided rack complete. (CSR.NO 1-11-10(New))

Supplying, fixing, and configuring 48 ports managed gigabit switch Layer 2 with 48 10/100/1000 Base-T ports management switch with 4 10GE SFP+ ports erected in provided rack complete. (CSR.NO 1-11-13(New))

Supplying, fixing, and configuring modularised multi-service router 802.11/a/n/ac unified Wave 2.5 GHz, with RJ-45 port, supporting 1 to 13 channels for 2.4 GHz, with unified wireless access point complete. (CSR.NO 1-11-18)

Supplying, installing and activating physical license pack software for multiple access point with management, configuration and trouble shooting for all access point in network complete. (CSR.NO 1-12-37)

Supplying, fixing, and configuring 10G Base -SR (SFP+) simplex MM transceiver erected in provided rack complete. (CSR.NO 1-11-15)

Supplying, fixing, and configuring media convertor 1000 Base-T to 1000 baseSX SC multi-mode media converter (550m) complete. (CSR.NO 1-12-38)

Supplying and fixing POE adaptor to provide DC supply to ethernet devices as per specification No. WG-NAS/PEA (CSR.NO 1-12-15)

Supplying and erecting 25m HDMI cord low voltage grade minimum 4k compliant to be laid in provided conduits with male/female 19 pin HDMI connectors complete. (CSR.NO 1-8-26)

Supplying and fixing 42 U floor mount server rack (Dimension-DxWxH – 800x1000x2070 mm) as per specification No. WG-NAS/RAK (CSR NO:1-12-29)

Supplying and fixing 15U wall mount rack (Dimension-DxWxH – 500x600x767 mm) as per specification No. WG-NAS/RAK (CSR NO:1-12-20)

Supplying and fixing 9U IP66 outdoor mount server rack with pole mount bracket (Dimension- DxWxH - 500x600x450 mm) as per specification No. WGNAS/RAK (CSR NO:1-12-31)

Supplying and fixing IP66 enclosure for fibre splicing complete. (CSR no - 1-10-29)

Supplying, fixing, and configuring min. 580 watt redundant power supply system erected in provided rack complete. (CSR NO:1-11-14)

SITC of 4 MP Full HD IP Dome /Bullet Camera Image Sensor 1/3" 4 megapixel progressivescan CMOS Effective Pixels 2304 (H) × 1296 (V) Electronic Shutter Speed Auto/Manual 1-1/100000 s Min. Illumination 0.5 lux F2.1 (Color); 0 lux (IR LEDs on IR Distance - nUp to 100 ft (30 m) Day/Night -auto (ICR)/Color/BW Backlight Compensation - BLC/HLC/DWDR White Balance - Auto/Manual Gain Control - Auto/Manual Noise Reduction - 3D Privacy Masking- Up to 4 areas Lens verifocal Length- 2.8 -12 mm Horizontal Angle of View 92° 86°-28 Compression H.265 (Main/High/Baseline Profile) /MJPEG Resolution 3 MP (2304×1296) 1080p Main Stream 4 MP ,30 fps 16x Digital zoom 60 fps, Resolution- Verifocal lens with in built mike ,320 db Corridor Mode Support Network Protocol IPv4/IPv6 HTTP HTTPS TCP/IP UDP UPnP ICMP IGMP RTSP RTP SMTP NTP DHCP DNS PPPoE DDNS FTP IP Filter QoS Compatibility -NON VIF Profile S CGI Max. User Access 20 users Mobile App - for iPhone iPad Android Phone and Tablet Power Supply PoE (802.3af) 12 V DC Working Environment -22°F to 140°F (-30°C to 60°C); 10% to 100% RH condensing Ingress Protection IP66 Vandal Resistance - IK10 Regulatory FCC Part 15B Class B (3 years warranty)

SITC of 1080p IR Bullet camera(2/12MP) with 1/2.8 inch CMOS, Total sensor pixels 1937 (H) x 1097 (V); 60fps, optical & Digital zoom in zoom out 2/12MP, 60fps, Sensitivity – (3200K, reflectivity 89%, F1.4, 30IRE) Color 0.0225 lx, Mono 0.0051 lx, With IR 0.0 lx, 134dB WDR, H.265; H.264; M- JPEG, Automatic Electronic Shutter (AES); Intelligent Dynamic Noise Reduction, In built mike, Intelligent Defog,Rule based alarms and tracking, Line crossing, Enter /leave field, Follow route, Loitering, Idle / removed object, People counting, Crowd density estimation, (Camera should be able run minimum 4 to 5 analytics simultaneously), 3D tracking based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), Audio detection (if microphone used), Privacy Masking, Pixel counter, Memory card slot, IR Rang 60mtr, Automatic Varifocal 2.8 to 12 mm, Alarm Input 1/1, Audio Input/output, RJ45, G.711, Signal-to-Noise Ratio >55 dB, Aud io Streaming Full-duplex / half duplex, ONVIF Profile S & G & T, IP67, IK10. SD card support up to 2TB. FTP, Dropbox and e-mail applications 3 year warranty

SITC of 4MP IR PTZ Camera with 1/1.8" progressive scan CMOS, Effective pixels 2688 x 1520 (4 MP), 60fps, 30x Optical Zoom (6.6 mm to 198 mm)(F1.5 to F4.8), 16X Digital Zoom, Minimum Illumination- Color: 0.0101 lux , B/W: 0.0016 lux, IR: 0 lux; IR distance 320m; White light illuminator 60m; 133dB HDR, H.265, H.264, MJPEG streams, Intelligent Dynamic Noise Reduction, BLC, White Balance, Pan Range 360° continuous, Tilt Range -90° to 5° (Auto-flip 190°), Pan/Tilt Modes - Pan: 0.1°/s - 240°/s; Tilt: 0.1°/s - 100°/s, Presets 256, Tours, Audio- 1/1 Channel In/Out, Micro SD card support up to 2TB, 32 individually configurable privacy masks,In built mike, Alarm inputs/outputs - 2/1, Dual Power options, Any object, Object in field, Crossing line, Entering field, Leaving field, Loitering, Following route, Idle object, Removed object, Counter, Occupancy, Crowd detection, (Camera should be able run minimum 6 analytics simultaneously), Condition change, Similarity search, Tampering, Object filters based on Duration, Size, Aspect ratio v/h, Speed, Direction, Color, Object classes (Upright persons, Bikes, Cars, Trucks), IP66 , IK10 ONVIF Profiles S & G & T, FCC, CE, UL Certified. In-built rain-sensing Wiper 3 year warranty

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC. (CSR.NO 1-12-1)

SITC of 8 TB (7200 RPM) Surveillance hard disk 8 TB storage capacity with SATA support 6GB/s NCQ 64 MB cache 3.5 inches, 3 years warranty

SITC of all in one Type Core i5 Family Processor Spec 2.3 GHz Ram 8 GB Memory Technology DDR4 Computer Memory Type GDDR4 Hard Drive Size 1 TB Hard Disk Description HDD hard Drive Interface Serial ATA SSD 256 GE Additional Graphics Coprocessor Intel UHD Graphics 630 Graphics Chipsel Standing Screen display Size 21.5 Inches Connectivity Type Bluetooth Wireless Type Bluetooth 801.11ac. Hardware Platform Windows Operating System Windows 10 Professional Warranty - 3 years

SITC of Full HD commercial LED TV DISPLAY-Screen Size 55-inch Aspect Ratio 16:9 Backlight Scanning 100Hz Resolution 1920 x 1080 pixels Viewing Angle178°/178° TERMINAL- VIDEO IN RCA X 1 AUDIO IN (L/R) RCA Pin Type X 2 HDMI IN HDMI 1.4 X 3 USB Input USB 2.0 X 2 RS232C Yes HDMI CEC Yes VGA IN Yes PC AUDIO IN Yes (1) (Share with AC)

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. (CSR.NO 1-1-9)

Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit (CSR.NO 1-2-2)

Supplying, installation, testing and commissioning of main fire pump (MFP / EP) suitable for water discharge of 2280 to 2850 LPM at 90 to 70 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 55kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/EP (2Nos Hydrant Pump and 1 Nos Sprinkler Pump) (CSR No : 13-1-5)

Supplying, installation, testing and commissioning of jockey fire pump (JP) suitable for water discharge of 180 to 240 LPM at 90 to 70 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 9.3 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, multi stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete, as per specification no. FF-MFP/JP (CSR No : 13-2-2)

Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 900 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 7.5 kW or of suitable Kw capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of cast iron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/BP (CSR No : 13-3-2)

Supplying, installation, testing and commissioning of main fire pump (MFP/DP) suitable for water discharge of 2280 to 2850 LPM at 90 to 60 m head driven by 76 HP or suitable HP capacity diesel engine at required working speed suitable for manual/automatic operation and casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical seal conforming to IS 1520. (b) Water cooled with radiator, diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12/24 volts DC electric starting equipment with battery of required AH capacity with necessary charger suitable to work on 230v, 50Hz AC supply, diesel tank of minimum 150ltr capacity with first filling of diesel up to 100% level with necessary piping with valves up to engine, exhaust pipe extended up to 10 m outside pump house duly insulated with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential silencer, instruments and the event of fault with audio indications etc. as required. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation aligning, proper levelling complete pump set with engine assembly and accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/SSC/DP (CSR No : 13-4-2)

Supplying and installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessories complete as per specification no. FF-FFA/PT (CSR No : 13-8-1)

For addition of capacity of main electric motor driven fire pump MFP (1 working) for hydrant system is more than 22 kW, add as follows in the basic cost of Item no 13-5-1 towards increased capacity switchgears and motor starters for main & jockey pumps along with necessary accessories for main & jockey fire pumps MFP=(1working), JP = (1working + 1standby, alternate run per start in auto mode) For main electric motor driven fire hydrant system pump of 55kW capacity & relevant capacity jockey pump add Rs… (CSR No : 13-5-1) (A-4)

For addition of fire sprinkler system to basic fire hydrant system control panel(FCP) which includes one main electric motor driven fire pump MFP (1working) having __kW capacity & relevant capacity jockey pumps, add as follows in the basic cost of Item no 13-5-1 towards increased capacity switchgears busbar and additional motor starters for main & jockey pumps along with necessary accessories with software & hardware for main & jockey fire pumps additional Sprinkler system MFP=(1working)@22kW, JP = (1working+1standby, alternate run per start in auto mode) @relevant capacity For main electric motor driven fire sprinkler system pump of 55kW capacity (1Working) & relevant capacity jockey pumps (1working+1standby, alternate run per start in auto mode, add Rs…. (CSR No : 13-5-1 : B-5) (for 1 nos Sprikler Pump )

For standby main electric motor driven fire hydrant/sprinkler system pump (MFP- 1 standby), add as follows in the basic cost of Item no 13-5-1 towards required switchgears and motor starter along with necessary accessories and updation of control logic with interlocking for operation of pumps MFP=(1working+1standby, alternate run per start in auto mode) JP = (1working+1standby, alternate run per start in auto mode) for main & jockey fire pumpsFor standby main electric driven fire hydrant/sprinkler system pump of 55kW capacity, add Rs….... (CSR No : 13-5-1 : c-5)

For addition of booster pump for fire hydrant/sprinkler, add as follows in the basic cost of item no 13-5-1 towards necessary accessories, indicators etc. with necessary interlocking and updation of control logic, add Rs....... for 11kW centrifugal type booster pump 1no(1working) , add Rs….... (CSR No : 13-5-1 : E-2)

Supplying and erecting G.I. pipe ‘C’ class ERW 20 mm dia with necessary fittings complete as per specification no. FF-PP (CSR No : 13-6-1)

Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP (CSR No : 13-6-2)

Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings complete as per specification no. FF-PP (CSR No : 13-6-3)

Supplying and erecting G.I. pipe ‘C’ class ERW 65 mm dia with necessary fittings complete as per specification no. FF-PP (CSR No : 13-6-4)

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP (CSR No : 13-6-5)

Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP (CSR No : 13-6-5)

Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP (CSR No : 13-6-7)

Supplying and erecting G.I. pipe ‘C’ class ERW 200 mm dia with necessary fittings complete as per specification no. FF-PP (CSR No : 13-6-8)

Providing coating of bitumen paint & 4 mm thick wrapping for underground 100 mm ring main of fire fighting system. (CSR No : 13-6-9)

Providing coating of bitumen paint & 4 mm thick wrapping for underground 150 mm ring main of fire fighting system. (CSR No : 13-6-10)

Providing coating of bitumen paint & 4 mm thick wrapping for underground 200 mm ring main of fire fighting system. (CSR No : 13-6-11)

Excavating hard murum / stone metal road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes & clearing the site by removing debris & making the site as required complete. (CSR No : 16-1-6)

Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 250 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete. (CSR No 7-6-7)

Supplying and erecting 75/80 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, SS screen, end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS (CSR No : 13-7-5)

Supplying and erecting 150 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, SS screen, end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS (CSR No : 13-7-7)

Supplying and erecting 200 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, screen of SS end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS (CSR No : 13-7-8)

Supplying and erecting 75/80 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV (CSR No : 13-7-13)

Supplying and erecting 150 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV (CSR No : 13-7-15)

Supplying and erecting 200 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV (CSR No : 13-7-16)

Supplying and erecting 50 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV (CSR No : 13-7-17)

Supplying and erecting 65 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV (CSR No : 13-7-18)

Supplying and erecting 75/80 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV (CSR No : 13-7-19)

Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV (CSR No : 13-7-20)

Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV (CSR No : 13-7-21)

Supplying and erecting 200 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV (CSR No : 13-7-22)

Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV (CSR No : 13-7-23)

Supplying and erecting 150 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV (CSR No : 13-7-25)

Supplying and erecting 200 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV (CSR No : 13-7-26)

Supplying and erecting gun metal single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV (CSR No : 13-7-34)

Supplying and installing wall mounting swinging hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per specification no. FF-FFA/HV (CSR No : 13-8-2) (in Staircase @ 37 + 41)

Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe, 15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL (CSR No : 13-8-4)

Supplying and erecting gun metal branch pipe of 63 mm dia fitted with 20 mm dia detachable hexagonal nozzle complete as per specification no. FF-FFA/NZ (CSR No : 13-8-7)

Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC (CSR No : 13-8-10)

Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV (CSR No : 13-8-13)

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG (CSR No : 13-8-14)

Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per specification no. FF-FFA/PS (CSR No : 13-8-15)

Supplying and erecting brass orifice plate having 6 mm. thickness, 140 mm outer dia with required diameter of inner hole at every single outlet hydrant valve as per specification no. FF-FFA/OP (CSR No : 13-8-16)

Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve of size ( 400 x 400 x 400)mm or hose pipe box of size ( 600 x 600 x 200)mm made from min. 1.5 mm thick CRCA sheet with angle iron work of min. of size (25 x 25 x 4) mm having front doors with viewing glass of size (200x150) mm and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5) (CSR No : 13-8-18)

Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade / SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5) (CSR No : 13-8-19)

Supplying and erecting 20 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV (CSR No : 13-7-31)

Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV (CSR No : 13-7-32)

Supplying and erecting 50 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV (CSR No : 13-7-33)

SITC Expansion Bellows (ISI marked) (Antivibration Rubber bellows )of half circular flanges on both end with tie rod fitting , ISI marked tested to 12 kg/ sq. cm pressure. Rate quoted shall include for supply and providing with companion, flanges, necessary gaskets, H.D.G.nuts-bolts & washers for 80 NB

SITC Expansion Bellows (ISI marked) (Antivibration Rubber bellows) of half circular flanges on both end with tie rod fitting , ISI marked tested to 12 kg/ sq. cm pressure. Rate quoted shall include for supply and providing with companion, flanges, necessary gaskets, H.D.G.nuts-bolts & washers for 150NB

SITC Expansion Bellows (ISI marked) (Antivibration Rubber bellows) of half circular flanges on both end with tie rod fitting , ISI marked tested to 12 kg/ sq. cm pressure. Rate quoted shall include for supply and providing with companion, flanges, necessary gaskets, H.D.G.nuts-bolts & washers for 250 NB

Supplying & erecting Water level controller 230/415 V, A.C.Four way under ground & Over head tank operation only (CSR No : 12-4-15)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 185 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR No : 7-2-27)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR No : 7-2-24)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR No : 7-2-31)

Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU (CSR No : 13-9-10)

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP. (CSR No : 9-2-8)

Supplying, installing, testing and commissioning FR, XLPE armoured cable 12 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU (CSR No : 13-9-13)

Supplying and erecting ABC powder type fire extinguisher as per IS : 13849/15683 of 1 kg capacity with necessary clamp for erection on wall.

Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 /15683 of 6 kg capacity with necessary clamp for erection on wall.

Supplying and erecting D.C.P. type fire extinguisher 6 kg capacity cartridge type with gun metal cap 150 gram CO2 gas cartridge, powder and brackets conforming to IS 2171-1985/ IS 15683 and complete erected with necessary clamps made from 50x6 mm M.S. flat with nuts & bolts grouted in wall complete.

Supplying and erecting D.C.P. type fire extinguisher 9 kg capacity cartridge type with Gun Metal cap 150 gram CO2 gas cartridge, powder and brackets conforming to IS 2171-1985 and complete erected with necessary clamps made from 50x6 mm M.S. flat with nuts & bolts grouted in wall complete.

Supplying and erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete. (CSR No : 13-15-1)

Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.

Providing Floor mounting stand for keeping 4 Nos. of FIRE buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of silver paint complete.

Providing and fixing of portable fire extinguisher Chemicl Foam Type of 6 Kg Capacity ( IS 10204). Complete with standard discharge valve with tube CI bracket for wall mounting etc. ( ISI MARKED) with signboard depicting the type, method of use etc. Application- at Canteen and Pantry area. Florescent type ( should glow in darkness)Indication stickers to be provided in various relevant location. rate should inclusive in this section. Confirming to IS:2190

Providing and fixing of portable fire extinguisher WATER TYPE 9 LTR. PORTABLE FIRE EXTINGUISHER ( IS 10204). Complete with standard discharge valve with tube CI bracket for wall mounting etc. ( ISI MARKED) with signboard depicting the type, method of use etc.Application- at Canteen and Pantry area. Florescent type ( should glow in darkness)Indication stickers to be provided in various relevant location. rate should inclusive in this section. Confirming to IS:2190

SITC Florescent type ( should glow in darkness)Indication stickers(As Per IS:9457 for Safety colour and Safety, size of 6cm x 15 cm IS:12349 for Fire Protection Safety Signs, IS:12407 for Graphics symbols for Fire Protection Plan.) like DANGER, NO SMOKING, EXIT, FIRE ESCAPE, EXSTINGUSHERS, HYDRANT, ARROWHEAD DIRECTION ,PUMP NAME on panel and PRESSURE SWITCH NO. ,HYDRANT POST BOX ,etc.to be provided. Also board " DO AND DONT" to be provided in various relevant location. The letter size as specify in the tender.

Supply, erection of Florescent type ( should glow in darkness) emergency telephone numbers like "police", "fire brigade", hospital", "doctors", & "responsible persons of the office", should be displayed in security cabin, reception area. The letter size as specify in the tender & the size is 50 cm x 30 cm

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. (CSR No : 6-1-19)

Making cement concrete foundation in 1:2:4 cement concrete with foundation bolts and nuts complete. (cost of wooden box is included) (CSR No : 16-3-5)

Supplying, erecting, testing and commissioning vane type water flow detector 100 mm dia. with 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4)Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track )synchronised switches 7) serviceable without draining pipes. (CSR No : 13-12-3)

SITC of Control Valve with turbine type automatic Alarm Gong to be connected with control valve, drain & test valve and all other necessary components as per manufacturer's specifications complete as required. The Valve must be UL Listed Size: 200NB

Supplying, erecting, testing and commissioning of quartzoid bulb sprinkler, 15 mm (½") dia. NBCM Body chrome finished, 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FFSPR. (CSR No : 13-12-1)

SITC of sprinkler flexible hose FM Approved stainless steel corrugated flexible pipe (hose) for dropping sprinklers below false ceiling ,pipe shall be 16 bar pressure 25 mm Dia with including all fittings like couplings bends, tees, Clamps, flanges. Gaskets, including cutting, welding / flanged joints necessary washers, nuts, bolts, L- brackets or S- brackets , rachets plates in case of falce ceiling , supprting arrangement above false ceiling with all other required accessories to be connected with header branch/sub branch and sprinkler unit for following pipe sizes. Assembly length 1500 mm (1 by 1/2)

SITC The Rosette Plate shall be fabricated by M.S.plate of 2mm thick and the finish shall be powder coated and color shall be as approved by architects /clients.

Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 1 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity, interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty FF-AFAS/CP (CSR No : 13-10-1 (New))

Supplying, installing, testing and commissioning of repeater panel with suitable battery backup of a minimum of 24 hours in normal condition and 30 min in alarm condition, 80 backlit alphanumeric LCD display with inbuilt buzzer to indicate fault/fire alarm, manual control keys for silence/mute and to reset the FACP from the repeater station. Panel size shall not more than 175 x 275 x 65 mm conforming to EN 54 or UL approved with 3 years equipment replacement warranty FF-AFAS/RP (CSR No : 13-10-5 (New))

Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to 32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300µA and alarm condition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020 EN 54 or UL Approved with 3 years equipment replacement warranty FFAFAS/SD . (CSR No : 13-10-6 (New))

Supplying, installing, testing and commissioning of intelligent addressable thermal/ heat detector with rate of rise cum fixed temperature thermistor complete with base as required, suitable for temperature variations from - 20°C to 38 °C for fixed-heat and rate-of-rise type detectors whereas 0°C to 90°C for high heat type detectors, in built isolation mode, suitable for industrial/ kitchen/ boiler room etc. with 3 years equipment replacement warranty, IS : 2175-1988 reaffirmed 2000, IS 15908:2021 standards FF-AFAS/SD. (CSR No : 13-10-8 (New))

Supplying, installing, testing and commissioning remote response indicators suitable to operate on 5 - 28 V dc supply having FR Polymer ABS Housing complete as per specification no. FF-FAAS/RRI (CSR NO:13-9-9)

Supplying, erecting testing and commissioning beam smoke detector four wire single ended reflected type with 8 " receiver having digital display for easy alignment, adjustable sensitivity & heater kit for transmitter/receiver and reflector with necessary connections on suitable back box. The protection range of beam detector is 70 to 100 m. (CSR NO:13-9-5)

SITC of Power Supply SITC of Power Supply or SMPS Output 24V - 3 Amp. with IP 65 Enclosures etc. Rate shall be including with required support system. key features as followed: - Universal input: -220-230 v AC; Overcurrent/overvoltage protection; Voltage adjustment +10% Spring-up crew terminal, IP20; DIN rail or panel surface mount

Supplying, installing, testing and commissioning of addressable manual call points ( break glass type/pull station type), made of addressable break glass plastic square in shape surface/flush mounted with "Break Glass" massage embedded on the glass, complete erected with mounting base and required accessories conforming to EN 54 or UL listed with 3 years equipment replacement warranty FF-AFAS/MCP. (CSR NO:13-10-9 (New))

Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 module duly erected. (CSR NO:1-6-27)

Supplying, installing, testing and commissioning of addressable horn cum strobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH. (CSR NO:13-10-13 (New))

Supplying, installing, testing and commissioning of addressable fire control/relay module complete as required, with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 reed relays, EN 54 or UL Listed FF-AFAS/CRM (CSR NO:13-10-10 (New))

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM (CSR NO:13-10-12 (New))

Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU (CSR NO:13-9-10)

Supplying, installing, testing and commissioning FR, XLPE armoured cable 4 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU (from Pressure switches to Main Panel) (CSR NO:13-9-11)

SITC of Fire command station including Graphical user Interface Software. The GUI based main network software shall be capable of graphically representing each node beingmonitored with floor plans and icons depicting the actual locations of the various systems; and/ or senCSRs' locations.The GUI Software shall be located in control room and shall monitor all the blocks panel connected with each other. The software shall provide the facility to Monitor over Fire Network along with the Fire detection Signal.The graphic Workstation shall act as an independent node communicating on the peer to peer network and shall not be dependent on the fire panel CPU for operation (Failure of any CPU shall not result in failure og Grapgic Workstation).

SITC of Full HD commercial LED tv ,DISPLAY-Screen Size 55-inch Aspect Ratio 16:9 Backlight Scanning 100Hz Resolution 1920 x 1080 pixels Viewing Angle178°/178° TERMINAL- VIDEO IN RCA X 1 AUDIO IN (L/R) RCA Pin Type X 2 HDMI IN HDMI 1.4 X 3 USB Input USB 2.0 X 2 RS232C Yes HDMI CEC Yes VGA IN Yes PC AUDIO IN Yes (1) (Share with AC)

Supplying and installing cat-6 STP cable suitable for networking complete as per specification. (1-10-5)

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO (CSR.NO 1-12-2)

SITC of Network Controller SITC of EN-54 Certified IP based EVAC PA controller capable of 12 zones in the system and expandable upto 400 zones with 14x 4 Audio matrix with full DSP functionality. 8 audio inputs, 4 audio outputs, 4 channel output matrix. Shall support the following: single line switching or redundant group A/B switching, amplifier redundany, 4 x 100V audio inputs and 12 speaker line outputs. Fault, warning and event conditions log. Built in message manager for 100 emergency/business calls up to 85 minutes. 10 control inputs and 13 control outputs. Impedance measurement and Pilot Tone supervision for speaker line monitoring. The controllers shall be able to exchange audio signals over the network without the need of a running PC/server, software dependent solutions shall not be accepted.The network controllers will be integrated using an interface module which is able to send and receive Dante audio to and from other Controllers.Frequency response (ref. 1 kHz) 20 Hz to 20 kHz (-0.5 dB), Signal-to-noise ratio (A-weighted): Line in to line out: 106 dB typical, THD+N < 0.05%, Crosstalk (line level) Line in to line out (0 dB gain): < 100 dB at 1 kHz, Sample rate 48 kHz, DSP processing resolution 24-bit linear A/D and D/A conversion, 48-bit processing. The omneo interface unit is able to send and receive Dante audio to and from other PA Controllers with the transmission of up to 16 digital audio input signals and 16 digital audio output channels with low latency shall be possible.Ethernet connectors (Primary /Secondary)100/1000 Mbit/s, RJ-45,integrated transformer isolationSampling rate 48 kHz. Data format 24 Bit. Audio channels Up to 16 ✕ 16 at 48 kHz, Audio flows Up to 16 ✕ 16 simultaneous audio streams,Latency across network 5 ms (typically). Multiple controllers should communicate over IP without need of running PC/Server. Graphics User Interface software should be considered for Monitoring and control of signal. Make and Model: - Equivalent to PVA-4CR12 + OM-1 .

SITC of Router SITC of EN54 Certified EVAC Router for adding 24 zones in the system and to route 4 channels into 8 100V audio inputs to 24 loudspeaker line outputs. 2-in-6 matrix. 20 Control Inputs, 26 Control Outputs. Shall support single line switching or redundant group A/B switching, amplifier redundancy. Impedance measurement and Pilot Tone supervision for speaker line monitoring. Make and Model: - Equivalent to Bosch PVA-4R24

SITC of 15 W Horn Speakers -15 W high efficiency ABS horn loudspeaker with weather protection IP65 - Max. Power: 22.5 W,Rated Power: 15 Watts, Power tapping: 15/7.5/3.75W - Effective frequency range(-10 dB) :(500 Hz to 5KHz) - SPL at rated power (1Khz) 115 dB - Self extingguishing acc. to UL94 V0 - IP65 acc. to IEC 60529, Safety acc. to EN60065 Make and Model: - Equivalent to Bosch LBC3470/00 .

SITC of Full Metal grille ceiling speaker 6W ceiling mount speaker with excellent speech & music reproduction - Max Power: 9W,Rated Power: 6Watts, Power Tapping: 6/3/1.5W - Effective frequency range(-10 dB) : 150 Hz to 15KHz - SPL at rated power (1Khz at 1 m) 108 dB - Opening Angle 1 KHz / 4 KHz:: 180° / 45° Make and Model: - Equivalent to Bosch LBD0606/10

SITC of 6 W Cabinet Speaker - 6W wall mount speaker with excellent speech & music reproduction - Max Power: 9W,Rated Power: 6Watts, Power Tapping: 6/3/1.5W - Effective frequency range(-10 dB) : 200 Hz to 15KHz - SPL at rated power (1Khz at 1 m) 96 dB - Opening Angle 1 KHz / 4 KHz (-6 dB): 150/70 Make and Model: - Bosch LBD3902-D/L

SITC of 6 W ABS Cabinet Speaker - 6W ABS wall mount speaker with excellent speech & music reproduction - Max Power: 9W,Rated Power: 6Watts, Power Tapping: 6 / 3 / 1.5 / 0.75 W - Effective frequency range(-10 dB) : 145 Hz to 18kHz (-10 dB) - SPL at rated power (1Khz at 1 m) 99 dB - Opening Angle 1 KHz / 4 KHz (-6 dB):165º / 88º(H/V) Make and Model: - Equivalent to Bosch LB9-UC06 .

SITC of 30 W Elliptical Horn Speakers 30W Horn speaker with excellent speech reproduction - Max Power: 45 W W,Rated Power: 30 Watts - Effective frequency range(-10 dB) :490 Hz to 4500 Hz - SPL at rated power (1Khz at 1 m) 115 dB - Opening Angle 1 KHz / 4 KHz (-6 dB):112 (H) /85 (V) -IP rating:- IP 65.

SITC of Volume control units 12W Power : 12 W (max) Attenuation Steps : 5 x 3 dB + off; Frequency Response : 50 Hz to 20 kHz; Current Consumption : 20 mA @ 24 V DC; Connection : Screw terminals; Color : White (RAL 9010); Mounting : U40; Rate shall be Inculding all other required accesCSRies such as a back box, faceplate etc. and complete as per guideline & site condition. Make and Model: - Equivalent to Bosch LBC1400/10

SITC of Volume control units 36W Power : 36 W (max); Attenuation Steps : 8 x 3 dB + off; Frequency Response : 50 Hz to 20 kHz; Current Consumption : 20 mA @ 24 V DC; Connection : Screw terminals; Color : White (RAL 9010); Mounting : U40; Rate shall be Inculding all other required accesCSRies such as a back box, faceplate etc. and complete as per guideline & site condition. Make and Model: - Equivalent to Bosch LBC1410/10

SITC of Wireless Handheld Microphones Power Source - Batteries 2 x LR6 / AA / UM3 1.5 V; Channels - 57 channels in steps of 125 kHz ; Response - 50 Hz ~ 15 kHz Rate shall be Inculding all other required accesCSRies and complete as per guideline & site condition.

SITC of Wireless Belt-pack Transmitters Batteries - Batteries 2 x LR6 / AA / UM3 1.5 V; Channels - 57 channels in steps of 125 kHz; Response - 50 Hz ~ 15 kHz Rate shall be Inculding all other required accesCSRies and complete as per guideline & site condition.

SITC of Wireless Microphone Receivers Power Source - 12V to 18 V, 500 mA; Channels - 57 channels in steps of 125 kHz; Antenna - xx ; Connector - BNC ; Rate shall be Inculding all other required accesCSRies and complete as per guideline & site condition.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR NO: - 7-2-8)

Supplying, erecting, testing and commissioning of 2 core shielded cable complete as per specification no. FF-PA/MCC (CSR NO: - 13-11-6)

Supplying, erecting & commissioning 10 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW (CSR NO: - 1-9-11)

Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit (CSR NO:1-2-2 (New))

Supplying and fixing 22 U floor mount rack (Dimension-DxWxH – 800x600x1176 mm) as per specification No. WG-NAS/RAK (CSR NO: - 1-12-22)

Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 module duly erected. (CSR.NO 1-6-27)

Supply Installation Testing & Commissioing of Programmable Logic Controller - capacity 140 DI, 30 DO, 100 max modbus inputs, 14 ethernet TCPIP , & profibus connectivity to Remote I/O , motherboard modular, assembled and mounted in 2 full height cabinets enclosure RITTAL with doors, ( PLC) CPU, power supply, Back planes, I/O cards, relay modules, terminals, racks, software, programme, connectors, prewired accessories, etc complete for Instruments and Uilities Related to it. Refer IO List, Cards Summary, PLC version Equiv to S7 1500 series of Siemens. Communication cards include Modbus, Ethernet TC pip for Hi end communications and SCADA application. refer Arch. Hardware Diagram of BMS system for compatibility. The relays shall be briad board mounted, with LED indication & with manual over ride (OEN /PLA / OMRON). One vertical portion to house the PLC and its accessories, and other vertical to house relays, terminal blocks, wiring troughs, identification rulers etc. The PLC elevation shall be at a visibile height for an upright standing person. The terminations also should facilitate ease of access and clearance for terminations. 3 years warranty

SITC of Remote I/O PLC Panel - with Supply Installation Testing & Commissioing of Programmable Logic Controller - capacity 140 DI, 30 DO, 100 max modbus inputs, 14 ethernet TCPIP , & profibus connectivity to Remote I/O , motherboard modular, assembled and mounted in 2 full height cabinets enclosure RITTAL with doors, ( PLC) CPU, power supply, Back planes, I/O cards, relay modules, terminals, racks, software, programme, connectors, prewired accessories, etc complete for Instruments and Uilities Related to it. Refer IO List, Cards Summary, PLC version Equiv to S7 1500 series of Siemens. Communication cards include Modbus, Ethernet TC pip for Hi end communications and SCADA application. refer Arch. Hardware Diagram of BMS system for compatibility. The relays shall be briad board mounted, with LED indication & with manual over ride (OEN /PLA / OMRON). One vertical portion to house the PLC and its accessories, and other vertical to house relays, terminal blocks, wiring troughs, identification rulers etc. The PLC elevation shall be at a visibile height for an upright standing person. The terminations also should facilitate ease of access and clearance for terminations. power supply unit, rack 20 DI, 6 DO, 10 max modbus inputs , 3 years warranty

SITC HUMAN MACHINE INTERFACE UNIT: Touch Panel 19''- The minimum hardware configuration of Human Machine Interface (HMI) shall be 2.1 GHz processsor (in case RISC & EPIC it shall be at least 1.2GHz), 8GB Main memory (RAM), 216 GB Auxiliary memory (Hard disk drive), 48x24x48 CD-R/W drive, 19” TFT/LED colour monitors, Graphic adaptor cards, Two speakers for audible alarms with configurable tones, Keyboard & Mouse, Dual 10/100/1000Mbps Ethernet ports, One hot pluggable for external Cartridge magnetic tape drive, Parallel, serial and USB (2.0) ports to accommodate printers, mouse and other peripherals etc. TP1900 Comfort- 3 years warrnty

SITC of BMS - SCADA Software System with 7000 tags (bit/memory tag) required licesnce valid for 5 years to be installed in the PC (Eng. Station) fault Alarm management , Energy Supervision, Preventive Maintenance tips, Auto Lighting Control Graphics, Trends, Events,History Configuration & various Management report generation, etc. System with required software & Interconnection with the PLC System and software to be installed in the Engineering Station. Post Commissioing support for Entire System - 30 Mandays to be included in basic package, 3 years warrnty

Supplying & installing GUI creation of graphics with dynamic dashboards, Min 25 nos of user friendly Graphics, legible , easy to use alongwtih the trends, comparison charts, Energy Monitoring Dashboard, Weekly report, monthly report, power quality paramters, Alarm management, historic trends, pop up alarms, fault status smmary etc as per user consultants guidelines. Verification of all tags, trouble shooting & on site simulated checks for readiness, 3 years warrnty

SITC of Communication shall be 600V AC grade 2 core, Cu flex, stranded, annealed, 0.5 sqmm twisted pair sheilded cable communication

SITC of Communication cables shall be 600V AC grade 4 core, Cu flex, stranded, annealed, 0.5 sqmm twisted pair sheilded cable

Supplying, installing, testing and commissioning FR, XLPE armoured cable 12 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU (CSR - 13-9-13 )

SITC of Instrumentation/Communication/Hi end cables shall be 600V AC 36 C X 1.5 sqmm,Cu, PVC Insulated , round wire armoured

SITC of Instrumentation/Communication/Hi end cables shall be 600V AC grade one triad shielded , 1.5 sqmm Cu Flex stranded cable for RTD PT 100 3 wire type

Supplying and installing cat-6 STP cable suitable for networking complete as per specification. (CSR No. 1-10-5)

SITC of End termials Glanding & Cable end terminations for above Cable. (Double compressed gland) 2 core, Cu flex, stranded, annealed, 0.5 sqmm twisted pair sheilded cable.

SITC of End termials Glanding & Cable end terminations for above Cable. (Double compressed gland) 4 core, Cu flex, stranded, annealed, 0.5 sqmm twisted pair sheilded cable.

SITC of End termials Glanding & Cable end terminations for above Cable. (Double compressed gland) 10 Core, 1.5 sqmm, unshielded, armoured, Cu flex stranded cable

SITC of End termials Glanding & Cable end terminations for above Cable. (Double compressed gland) 36 C X 1.5 sqmm, Cu, PVC Insulated , round wire armoured Cable.

SITC of End termials Glanding & Cable end terminations for above Cable. (Double compressed gland) 1.5 sqmm Cu Flex stranded cable for RTD PT 100 3 wire type.

SITC of End termials Glanding & Cable end terminations for Supplying and fixing tool-less shutter keystone jack (RJ-45) in provided patch panel complete as per specification no. WG-NAS/KJ (CSR N0. - 1-12-3)

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO (CSR N0. - 1-12-2)

Supplying and erecting rigid steel conduit 16 SWG 25 mm dia. with necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC. (CSR N0. - 1-1-4)

SITC of JB Polycarbonate Housing , outdoor type, IP 65, size Aprox 750 mm X 1200 mm for Terminal Enclosure Box as per following specification 1 ) 4 no's terminales CU. suitables for 10 pair , 0.5 sqmm. 2 )2 no's terminales CU.2 Pair X 0.5 sq mm 3) 2 no's terminales CU. ,10 Core, 1.5 sqmm 4) 2 nos of terminals for 20 Core, 1.5 sqmm. 5) 2 nos of terminals for 36 C X 1.5 sqmm 6) 2 nos of terminals for one triad shielded , 1.5 sqmm Cu Flex stranded cable,, 3 years warranty

SITC of Operator Workstation Workstation with latest i7 procesCSR, 16 GB RAM, 2 TB HDD, keyboard, mouse, windows 11 Operating system, Graaphics Card: ATI 4GB. Software & Licenced Anti-Virus Software LED Colour Monitor of 15.6 inch. Rate shall be Inculding with required all other accesCSRies Complete as per guideline & site condition inculding Intuikey Digital Keyboard W/ LCD for use with DIVAR DVR AND System 4 Multiplexers + License Workstation expansion + SMA license for 1 year, MBV-XWSTPLU.

LEVEL CONTROLLERS SITC of digital percentage level indicator for the following storage tanks consisting of display unit and level senCSR. The display unit should have 2-1/2 digit seven segment LED to display the levels as 0%, 10% --- 100%. The unit should be weather proof and wall / panel mounted input to the unit should be 230V AC. The level senCSR should consists of float operated magnetic float switch with one PUF float suitable mounting flange and flame proof enclosure. The unit shall be BMS Compatable; Complete to be erected as required as per site condition & guideline & satisfaction of Engineer-in-chargeinclude necessary Chain pulley and guide rail arrangement for easy maintenance. Complete to be erected as required as per site condition & guideline & satisfaction of Engineer-in-charge , 3 years warranty

Supplying, erecting, testing and commissioning 11KV HT metering cubical (compact / vertical type) approved by MSEDCL / licensee fabricated with 2mm (14 SWG) M.S. sheets with supporting angle, painted with powder coating /epoxy paint of required shade, copper bus bar size 25 x 6 mm, heavy duty mechanical lock, with counter meter for measuring no of times the opening of meter door, top side cover (CT, PT cover) interlock with meter door, epoxy casted 3 nos. CT having required ratio between 50/5A to 200/5A, VA 10 or 15, Class 0.2S, epoxy casted 3 nos. PT having ratio 11000/V3/110/V3 VA 50, Class 0.2suitable for provided trivector meter, and provision for incoming and outgoing cables complete duly tested by licensee with necessary test certificates and erected on provided plinth/ cc foundation. (CSR No : 6-4-2)

Supplying, erecting, testing & commissioning 11kV, 630A, 21kA/3sec, 3 way outdoor, extensible motorised SCADA compatible RMU, internal arc tested consisting of 1 no. feeder with 1 LBS and 2 nos. feeder with 2 VCB. compliant to IEC 62271 -100,200 and 102, as per specification no. SW-HTS/RMU SCADA (CSR No : 5-9-21)

Supplying, erecting, testing & commissioning 11kV, 630A, 21kA/3sec, 4 way outdoor, extensible motorised SCADA compatible RMU, internal arc tested consisting of 2 nos. feeder with 2 LBS and 2 nos. feeder with 2 VCB compliant to IEC 62271 -100, 200 and 102, as per specification no. SW-HTS/RMU SCADA (CSR NO: 5-9-18 )

Supplying, erecting, testing & commissioning 11kV, 630A, 21kA/3sec, 5 way outdoor, extensible motorised SCADA compatible RMU, internal arc tested consisting of 2 nos. feeder with 2 LBS and 3 nos. feeder with 3 VCB compliant to IEC 62271 -100, 200 and 102, as per specification no. SW-HTS/RMU SCADA (CSR NO: 5-9-19 )

Supplying, installing, testing & commissioning compact substation with 3 phase, 11/0.433, 50 Hz., 630 kVA, Mineral oil immersed Copper wound ,without gas cushioning ,hermetically Sealed transformer having indoor type transformer bushings, with HT side (incoming side) load break switch of appropriate capacity and LT side (outgoing side) MCCBs (4 pole) of appropriate capacity , with inbuilt metering cubical, using type A winding insulation (kraft paper), standard accessories complete with test certificate with losses below 1860 Watts at 50% load, 5300 Watts at 100% load for transformer, as per IS:1180 (part 1) : 2014 , with necessary permissions of Electrical Inspectors per specification no SS- TR- SL (CSR No - 10-4-3)

Supplying, installing, testing & commissioning compact substation with 3 phase, 11/0.433, 50 Hz., 1000 kVA, Mineral oil immersed Copper wound ,without gas cushioning , hermetically Sealed transformer having indoor type transformer bushings, with HT side (incoming side) load break switch of appropriate capacity and LT side (outgoing side) MCCBs (4 pole) of appropriate capacity , with inbuilt metering cubical, using type A winding insulation (kraft paper),standard accessories complete with test certificate with losses below 2790 Watts at 50% load, 7700 Watts at 100% load for transformer, as per IS:1180 (part 1) : 2014 , with necessary permissions of Electrical Inspectors per specification no SS- TR-SL (CSR No - 10-4-5)

Supplying, erecting and commissioning of diesel generating set with alternator of 750 kVA output continuous rating, 3 phase, 415 V, 50c/s 0.8 p. f. A.C a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising of meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level upto 75 dB at 1.0 m, provided with first filling of oil, diesel etc. and obtaining necessary approval from Electrical Inspector as per specification no. GEN-DG (CSR No - 11-1-22)

SITC of D.G. Exhust Pipe 150 mm class B, M.S. black pipe with bends & other accessories as required with 'Thermal insulation with 100 mm thick rock wool and cladded with 0.6 mm Al. foil for 150 mm dia also with including required adequate supporting system (The Distance to be Considered as per PWD Guidelines and Approval)

Supplying , erecting & terminating XLPE insulated, galvanised steel formed wire armoured (strip) cable 11 kV(UE), 3 x 120 sq. mm. aluminium conductor laid in provided trench / pipe as per specification no. CB-HT (CSR NO : 7-3-10)

Providing and erecting Heat shrinkable indoor termination kit for 11 kV ( E ) XLPE HT cable 3x120 to 185 sq. mm. with necessary material as per specification no. CB-JT/HT (CSR NO : 7-5-2)

Providing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill Ground Enhancing compound complete with all materials, testing & recording the results as per specification no ESE -LA (CSR NO : 9-1-6)

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP (CSR NO : 9-1-3)

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP. (CSR NO : 9-2-7 )

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non-corrosive bond with required joints As per specification no. EA-EP. (CSR NO : 9-2-8 )

Supplying & erecting cast iron cable indicator plate buried along with route of cable for PVC / XLPE armoured cable as per specification No. CB-CIP (CSR NO : 7-8-1 )

Supplying standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use, scissors, anti-septic solution,etc. (All above contents shall be of standard makes) (CSR NO : 10-6-24 )

Providing printed instruction chart for treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete. Shock treatment chart (CSR NO : 10-6-22 )

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class C insulation conforming to IS: 15652 – 2006 tested having 3mm thickness up to 33 kV11 KV insulating mats (CSR NO : 10-6-27 )

Supplying and fixing PVC synthetic elastomer electrically insulating mat with class A insulation conforming to IS: 15652 – 2006 having 2 mm thickness up to 3.3 kV 33 V insulating mats (CSR NO : 10-6-25 )

Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working upto 22 kV supply complete. Hand gloves (CSR NO : 10-6-23)

Supplying and erecting GI sheet 1.6 mm (16 SWG) caution board of size 200 x 150 mm duly painted with red oxide and enamel paint in Marathi, Hindi and English erected at position for medium voltage (415 Volt) installation with compliance to IS 2551-1982 (CSR NO : 6-1-15)

Supplying and erecting GI sheet 1.6mm (16 SWG) caution board of size 250 x 200 mm duly painted with red oxide and enamel paint in Marathi, Hindi and English erected at position for HV/EHV (11000 Volts) installation with compliance to IS 2551-1982 (CSR NO: 6-1-16 )

Supplying & laying (including excavation) reinforced cement concrete pipe of IS 458:2003 NP-2 class of 250 mm internal diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete. (CSR NO: 6-1-7 )

Supplying and erecting LT CT multifunction DLMS compliance energy meter of accuracy of class 0.5 , 3x240V,50 Hz with optical & RS 232 port, backlit LCD, measure & display trivector energy, load survey, TOD, tamper detection & logging, power ON /OFF events, instantaneous parameters of rating 1/5 A with display in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided M.S. box and connected to CTs. (CSR NO: 6-3-5 )

Providing and making second class Burnt Brick masonry with conventional /I.S. type bricks in cement mortar 1:6 in foundation sand plinth of inner walls /in plinth external walls including bailing out water manually, striking joints on unexposed faces, raking out joints on exposed faces and watering etc. Complete. (CSR No-16-2-1)

Providing and fixing reinforced cement concrete cover of size 60 cm x 45 cm with frame over inspection chamber etc. complete of medium duty (100 Kilogram). (CSR No-16-2-4)

Excavating hard murum / stone metal road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes & clearing the site by removing debris & making the site as required complete. (CSR No-16-1-6)

Supplying, installing, testing and commissioning of 600 kWp ON-GRID Solar PV System / Plant consisting Solar PV Poly Crystalline Panel (335 Wp X 1800 Nos.) and Solar ON-GRID Inverter of similar capacity (THD<3%) with interconnecting wires / cables up to solar ON GRID inverter, proper base plate, canopy box to house Inverter and necessary accessories i.e. ACDB/ DCDB , MCB etc. wiring up to solar Inverter in casing and capping, display board, sign board, two distinct earthing, lightning arrester, liaisoning charges, remote monitoring system with maintaining card / chip for 5 years including net charges for RMS System, complete up to net meter Installation and export to the grid with 5 year ON-SITE warranty and fully comprehensive maintenance contractas per Specification no. ESD-RT-ONG. (Refer : Annexure Sheet - 600-S)

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. (CSR No 6-1-19)

Supplying and installation of Solar PV Module cleaning unit consisting of nozzles spray, necessary pipes, valves, post, electronic panel board concealed with weather proof cabinet, spreading water periodically for removal of dust, related motor pump, controller, timer and nozzles set suitable for covering 600 KW Solar PV Module. (Approx. 35 Sq. Mtr. PV Module area) (Refer : -Annexure Sheet - 600-CU)

Providing and fixing high-density polyethylene (HDPE) container one piece moulded triple layer water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres. (CSR - 4-8-7 )

Supplying erecting testing and commissioning cubicle pattern electrical control panel (Solar Power evacuation Panel (600 Kwp System) as per SLD) made of 14 /16 / 18 / 20SWG MS Sheet IP 54 rated duly painted with 2 coats of enamel paint comprising of the following Incommer 1250A FP ACB as Incommer And 7 nos of 400 Amp FP MCCB + 1 no of 630 amp FP MCCB as outgoing (Refer : - Annexure Sheet - 600 - ECP)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR No 7-1-24)

Supplying and installing cat-6 armoured cable with ECCS tape suitable fornetworking as per specification No. WG-COC/NC (CSR - 1-10-7)

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 400 mm width & 75 mm height complete with necessary coupler plates & hardware. (CSR - 7-11-9)

Supplying, installing, testing and commissioning of 300 kWp ON-GRID Solar PV System / Plant consisting Solar PV Poly Crystalline Panel (335 Wp X900 Nos.) and Solar ON-GRID Inverter of similar capacity (THD<3%) with interconnecting wires / cables up to solar ON GRID inverter, proper base plate, canopy box to house Inverter and necessary accessories i.e. ACDB/ DCDB , MCB etc. wiring up to solar Inverter in casing and capping, display board, sign board, two distinct earthing, lightning arrester, liaisoning charges, remote monitoring system with maintaining card / chip for 5 years including net charges for RMS System, complete up to net meter Installation and export to the grid with 5 year ON-SITE warranty and fully comprehensive maintenance contractas per Specification no. ESD-RT-ONG. (Refer : Annecture Sheet - 300-S1)

Supplying and installation of Solar PV Module cleaning unit consisting of nozzles spray, necessary pipes, valves, post, electronic panel board concealed with weather proof cabinet, spreading water periodically for removal of dust, related motor pump, controller, timer and nozzles set suitable for covering 300 KW Solar PV Module. (Approx. 35 Sq. Mtr. PV Module area) (Refer : Annecture Sheet - 300-CU)

Providing and fixing high-density polyethylene (HDPE) container one piece moulded triple layer water tank made out of high density polyethylene and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres. (CSR - 4-8-7 )

Supplying erecting testing and commissioning cubicle pattern electrical control panel (Solar Power evacuation Panel (600 Kwp System) as per SLD) made of 14 /16 / 18 / 20SWG MS Sheet IP 54 rated duly painted with 2 coats of enamel paint comprising of the following Incommer 630 A FP ACB as Incommer And 4 nos of 250 Amp FP MCCB + 1 no of 630 amp FP MCCB as outgoing (Refer : - Annexure Sheet - 300 - ECP)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 300 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL (CSR No 7-1-24)

Supplying and installing cat-6 armoured cable with ECCS tape suitable for networking as per specification No. WG-COC/NC (CSR - 1-10-7)

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 400 mm width & 75 mm height complete with necessary coupler plates & hardware. (CSR - 7-11-9)

SITC of Gross Metering along with epoxy casted 3 nos. CT having required ratio between 600/5A, VA 10 or 15, Class 0.2S, epoxy casted 3 nos with reuired wiring,.Terminals Links, testing in housing box and calibration at Parking Area Sealed by MSEDCL

SITC of Vertical Air Termination Solid Aluminium with base- 16 mm dia and 1000 mm long. Air Terminal Base should be tested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform in an accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol Supply of Special standing seam fixureClamp for Air terminal on Metal Structure -Site specific

SITC of Vertical Air Termination Solid Aluminium with dia 16 mm, for LPS suitable for firm routing on wall / parapet/ roof or sheet/calzip tested by accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017

SITC of Cross splicer should be tested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform in an accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol 10 Dia Stainless steel Air termination- 3 Mtrs Long with 2 nos SS Clamp Suitable for side mounting on wall

SITC 10 Dia Stainless steel Air termination- 3 Mtrs Long with special Fixing Arrangement (movable support + 3 Nos of 14mm Dia, 2mm Thick Al. pipe)

SITC of concrete block for fixing/Mounting Vertical Air Termination / Mast on RCC Floor with special concrete compound Quick and easy mounting of interception rod using anchor.

SITC of Cross splicer should be tested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform in an accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol 10 Dia Stainless steel Air termination- 2 Mtrs Long with 2 nos SS Clamp Suitable for side mounting on wall

SITC Air Terminal 16mm Dia and 1500mm Length Solid Aluminium Blunt Special Fixing Arrangement for fixing Air Terminal

SITc of 8 mm dia solid Aluminium Conductor tested as per IEC 62561- 2 conducted in the Govt. aggregated thirty party laboratory to meet the requirement of IS / IEC 62305

SITC of Standing Seam clamp :To hold 8 mm Al conductor at every 1m dist on the top roof without any drilling on roof , Installation can be made through simple fastening system ,mainly used for seaming sheet roof application tested as per IEC-62561-2 for conditioning & Ageing test & conducted in the Govt. accredited Third party laboratory to meet the requirements of IS/IEC 62305

SITC of Special fixure Clamp for conductor on Metal Structure roof/wall-Site specific

Making cement concrete foundation including excavation ( 100x100x50 ) mm deep in 1:3:6 cement concrete,Duly plastered, with necessary curing and finishing complete.

SITC of Expansion Piece without connector to compensate the expansion and contraction of Solid Round Al. Conductor during temperature variations to be provided on conductors length over 20 meters to connect Solid Round Al. Conductor at both ends to meet the requirements of IS/IEC 62305.

SITC of Al. Straight Splicers for 8mm and 10 mm Conductor to meet the requirement of IS IEC 62305 tested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform in an accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol

SITC of Cross splicer should be ttested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform in an accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol

SITC of Al. Straight Splicers for 8mm and 10 mm Conductor to meet the requirement of IS IEC 62305 tested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform in an accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol

SITC of Cross splicer should be ttested for conditioning, Ageing Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform in an accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1 2017 protocol Supply of Al conductor holding clamp suitable for fixing 8 mm ,.Conductor holder @ 1 meter distance should be tested as per IEC-62561-2 conditioning & Ageing test, conducted in the Govt. accredited thirty party laboratory to meet the requirement of IS/ IEC 62305 Supply of Pipe type Clamp Holder -SS-Round for fixing conductor on pipe to meet the requirements of IS /IEC 62305 -3

SITC universal parapet conductor holder, MOC - Polyamide/Nylon suitable for 8 to 10 mm dia conductor, Used for solid round AI air terminal on Parapet/Concrete wall, fixed using screws as per IS/IEC 62305 Length 100- 150 mm

SITC Each down-conductor should be provided with a test link in order to disconnect the earth termination system for enabling measurements. SS Test Link To connect Round to Flat conductor.

SITC of 25 X 6 mm GI strip from AL Conductor to the earth pit station and further the same strip shall be used for interconnecting all the earth pits below ground leve Zinc coating: 500 g/m square (Approx :70 micron coating) Should be tested and use exclusively for lightning protection ,earthing system and ring equipotential bonding

SITC LPES Flat strip holder with female thread M^ via Slotted clamp, thickness 5 mm, Fixed conductor routing conductor support GI 30 x 3.5 mm height of conductor holder as per IEC 62305 Part 151212

SITC Earth Electrode Cu Bonded Steel Rod 14.2mm dia x 3000mm-(250Microns) Eco Friendly rust proof heavy duty weather proof Polyethylene Earth Pit Chamber with following dimensions :254 mm dia (top), 330 mm dia (bottom) & 260 mm (height). 14.2 / OD SS Clamp Both Side OEM Safe carbon based backfill compound - 50 Pounds

SITC of Electric Traction Passenger Lift with 1299498 • Rated capacity :- 10 Passenger/680Kg • Floors :- G+1 floor (2 Stops/2 Landings) • Travel :- 3 to 4.2 mtrs • Location of Lift Machine:- MR/MRL • Rated speed :- 1.0mps VS • Car/Landing door clear opening of 800 mm wide x 2000 mm high • Clear Car size of 1300 mm wide x 1350mm deep x 2250mm high • Lift shaft available having clear size of 1495 mm wide x 1805 mm deep,mm Pit depth, mm Overhead. • Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landingdoors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issuedby NABL accredited or Independent test laboratory). • Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge.• COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor. LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings • Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters. The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provisionfor addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class.• ARD complete with necessary SMF VRLA batteries.• Fireman controller having fireman switch at fire Landing. • CCTV surveillance system comprises of 2 nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min.18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength.• Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work.• Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery,adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting andhoisting lift machine etc. complete as per specification no. LFT.• General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. • The above rate includes Fully Comprehensive AMC for one year from the date of commissioning. (CSR NO - 17-1-4)

SITC of Electric Traction Passenger cum Stretcher/Hospital Lift with • Rated capacity :- 20 Passenger/1360Kg • Floors :- G+1 floor (2 Stops/2 Landings) • Travel :- 3 to 4.2 mtrs • Location of Lift Machine:- MR/MRL • Rated speed :- 1.0mps VS • Car/Landing door clear opening of 1100/1200 mm wide x 2000 mm high Lift shaft available having clear size of 1500 mm wide x 1800 mm deep, 1500 mm Pit depth, 3000 mm Overhead. • Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid(non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory) • Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge. • COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Liftcar, LMR & FCC/ground floor. LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings.Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, bchange direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters, The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class.• ARD complete with necessary SMF VRLA batteries. • Fireman controller having fireman switch at fire Landing. CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for min. 90 days with min. 20" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. • Lift Machine of Gearless PMSM of suitable kW with duty cycle of minimum 120 starts/hr (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on LMR floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength • Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work. • Minor civil work such as alteration work if any necessary for erection of landing door frames and it's accessories e.g. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing and fixing steel girders/RCC work having adequate strength for mounting and hoisting lift machine etc. complete as per specification no. LFT. • General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. • The above rate includes Fully Comprehensive AMC for one year from the date of commissioning. (CSR NO - 17-1-10)

For Lift having 1100mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade solid(non-cladded) landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrows-indicators, extension of guide rails, shaft wiring with trunking, travelling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories etc. necessary for the normal safe functioning of lift installation complete (CSR No - Add on - A6)

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB (CSR NO - 5-3-13)

Supplying, erecting & marking DPMCB 6 A to 32 A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB (CSR NO -5-3-7)

Supplying, fixing and commissioning 2 pole, RCBO 6 / 10 / 16 / 20 / 25A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO (CSR NO -5-6-9)

Supplying, fixing and commissioning 4 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO (CSR NO -5-6-13)

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/ FP MCB / RCCB / RCBO complete erected on angle iron/GI frame. (CSR NO -5-4-13)

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. (CSR NO -6-1-19)

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete. (CSR NO -1-6-1)

Supplying and erecting modular type 3 pin 6A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete (CSR NO -1-6-10)

Supplying and erecting Ceiling rose / Batten holder / Slanting holder /hanging cord switch / hanging bell push / pendant holder bakelite base 6A. erected on filled polypropylene board or polished double wooden block/ PVC junction box. (CSR NO -1-5-7)

Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f.>0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver,IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty.Supplying and erecting electronic type driver for indoor LED 25W-40W fixture (CSR NO 2-1-15)

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module duly erected.Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module duly erected. (CSR NO -1-6-29)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR NO -7-2-31)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 2.5 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU (CSR NO -7-2-8) (For car Lighting)

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP (CSR NO -9-1-2)

Supplying and erecting annealed bare copper wire of high purity of required sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws complete. (CSR NO -9-2-4)

Supplying, erecting, testing and commissioning 10 HP, VRF / VRV air conditioning system, outdoor unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. Celsius and non stop cooling even at 56 deg. Celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.

Supplying, erecting, testing and commissioning 12 HP, VRF / VRV air conditioning system, outdoor unit (ODU) type-IV OEM standards working on HFC free refrigerant R410A or other required/ suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. Celsius and non stop cooling even at 56 deg. Celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 meter operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter / control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil seperator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V + 10%, 50 Hz, 3 phase power supply, internal wiring and discharge of refrigerant, etc. all housed in powder coated weather proof cabinate on provided angle iron frame or suitable foundation connected to the system in approved manner complete.

Supplying, erecting, testing and commissioning 14 HP, VRF / VRV air conditioning system, outdoor unit (ODU) type-IV OEM standards working on HFC free refrigerant R410A or other required/ suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. Celsius and non stop cooling even at 56 deg. Celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 meter operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter / control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil seperator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V + 10%, 50 Hz, 3 phase power supply, internal wiring and discharge of refrigerant, etc. all housed in powder coated weather proof cabinate on provided angle iron frame or suitable foundation connected to the system in approved manner complete.

Supplying, erecting, testing and commissioning 16 HP, VRF / VRV air conditioning system, outdoor unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. Celsius and non stop cooling even at 56 deg. Celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.

Supplying, erecting, testing and commissioning 18 HP, VRF / VRV air conditioning system, outdoor unit (ODU) type-IV OEM standards working on HFC free refrigerant R410A or other required/ suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. Celsius and non stop cooling even at 56 deg. Celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 meter operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter / control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil seperator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V + 10%, 50 Hz, 3 phase power supply, internal wiring and discharge of refrigerant, etc. all housed in powder coated weather proof cabinate on provided angle iron frame or suitable foundation connected to the system in approved manner complete.

Supplying, erecting, testing and commissioning 22 HP, VRF / VRV air conditioning system, outdoor unit (ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. Celsius and non stop cooling even at 56 deg. Celsius and coefficient of performance (COP) 3.00 to 4.00, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.

Supply, Installation, Testing and Commissioning of VRF/VRV based ceiling suspended 4 Way cassette indoor unit (IDU) compact/ standard size of nominal cooling capacity 2.6 TR (918 cfm) to 2.8 TR (1100 cfm) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides, indoor unit complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1- phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charged as per requirement during installation and connected to the system complete.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indoor unit (IDU) compact / standard size of nominal cooling capacity 2.0TR ( 618 cfm ) / 2.3TR ( 671 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indoor unit (IDU) compact / standard size of nominal cooling capacity 1.5TR ( 512 cfm ) / 1.8TR ( 618 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indoor unit (IDU) compact / standard size of nominal cooling capacity 1.0TR ( 541 cfm ) / 1.3TR ( 512 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete.

Supplying, installing, testing and commissioning split type variable speed inverter technology room Air conditioning unit 2 TR capacity having ISEER minimum 4.50 suitable to operate on 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall/ floor mounting type complete with Refrigerants R410 A /R32 and copper condenser at position. specification no. APAC/ SAC

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete.

supplying and installation of high pressure grade required size copper connection Y or T -joints / refnet for liquid and suction line complete erected on wall / ceiling with supports/ raceways, nitrile rubber insulation, painting etc. with brazing and testing for leakage confirming the normal operation of the VRV/VRF air conditioning system

Supplying, erecting, testing and commissioning centralised programmable remote control panel (HMI) touch manager controls minimum 16 system of minimum 64 ODU's can be controlled and up to 992 IDU's can be individually mounted and controlled indoor units having minimum 200 mm size colour LCD touch panel, yearly scheduled, power proportional distribution function, temperature limitation, history function complete erected on wall with an arrangements to integrate with provided fire alarm system.

supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4 mm dia (OD) for liquid line / suction line supply and return piping and suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fitting such as bends, tees, valves gauge, strainer with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra voilet radiations complete with OEM standards of VRV/VRF air conditioning system.

supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line / suction line supply and return piping and suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fitting such as bends, tees, valves gauge, strainer with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra voilet radiations complete with OEM standards of VRV/VRF air conditioning system.

supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) for liquid line / suction line supply and return piping and suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fitting such as bends, tees, valves gauge, strainer with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra voilet radiations complete with OEM standards of VRV/VRF air conditioning system.

supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line / suction line supply and return piping and suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fitting such as bends, tees, valves gauge, strainer with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra voilet radiations complete with OEM standards of VRV/VRF air conditioning system.

supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1 mm dia (OD) for liquid line / suction line supply and return piping and suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fitting such as bends, tees, valves gauge, strainer with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra voilet radiations complete with OEM standards of VRV/VRF air conditioning system.

supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2 mm dia (OD) for liquid line / suction line supply and return piping and suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fitting such as bends, tees, valves gauge, strainer with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra voilet radiations complete with OEM standards of VRV/VRF air conditioning system.

supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping and suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fitting such as bends, tees, valves gauge, strainer with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV/VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra voilet radiations complete with OEM standards of VRV/VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying and erecting an air flow regulating valves / dampers in provided flexible or rigid duct / pipe of 100 mm size with an alteration for existing flexible PVC pipe duct and necessary joints, sealing, coupling, complete at position.

Supply, installation, testing and commissioning of manually operated, opposed blade, duct mounted flanged volume control damper of required sizes in GI construction complete with operating mechanism, mounting arrangement, rubber refrigerant kits etc. complete.

Supply, fabrication, installation and testing of flexible canvass connections constructed between ductable unit / dampers / ducting of required size with fire resist flexible double canvas sleeve complete.

Providing adhesive thermal insulation for supply / return air duct with 19 mm nitrile rubber insulation having R-value as per the prevailing provisions in ECBC-2007.

Carrying out core cutting of size 3'' to 5'' dia x 15'' length in the c.c./rock/stone wall with help of specialized core cutting machine in proper manner and finishing the site as original.

Supplying and installing of coller damper of galvanised iron material of upto 120 microns for anti corrosive resistance for supply air grill of required size

Supplying and erecting aluminium powder coated linear grill of suitable size for width length without collar dampers having matching colour with the existing false ceiling and suitable for deflection of 15/30/45 degree.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting hot dipped galvanised ladder type cable tray manufactured from 16 SWG (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware.

Providing & erecting Hot dipped galvanized cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) GI sheet of 150 mm width & 20 mm height complete with necessary hardware in approved manner.

Providing & erecting Hot dipped galvanized cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) GI sheet of 300 mm width & 20 mm height complete with necessary hardware in approved manner.

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV.

Supplying and erecting HMS PVC conduit 25 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation.

Supplying and erecting iron sheet metal work consisting of CRCA sheets various sections of iron plates chequered plates rods bars MS pipes etc. for panel board or any other purpose with bending cutting drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supply, Installation, Testing & Commissioning of Air Cooled Screw Chiller with VFD Starter complete with multiple / single Semi Hermetic Screw Compressor, Shell & Tube Condenser & Chiller Expansion Valves, First Charge of Gas R134a / R 410A & Oil etc. & unit mounted VFD. The plant should be suitable for the following parameter Capacity. Actual Capacity at Baramati Ambient Conditions. The Chillers should be installed on a baseframe along with Antivibration Spring mounted pads. Detailed Specifications as per tender Documents. The Chillers shall be made available for Factory Testing as per AHRI standards on AHRI certified Test Bed for multiple point testing. The chiller shall be AHRI / Eurovent certified. Actual Capacity 120 TR Chilled Water Inlet Temperature = 12.0 Deg.C Chilled Water Outlet Temperature = 7.0 Deg.C Air Temperature over Condenser = 40.0 Deg.C. Evaporator Fouling Factor: 0.0001 FPS. C.O.P.: Not less than 2.90. IKW/TR: Not more than 1.30 @ 100% Load. The equipment shall be complete with electrical panel and microprocessor control, with the following specifications:. a. Single Phasing Prevention. b. Under / Over Voltage Protection. c. Phase Reversal protection. d. Independent Set Points for each refrigeration ckts. e. HP / LP Trip signal interlocking. f. Interlocking for Chilled water Flow Switch. g. Auto / Manual / Test Mode facility. h. Runtime equalization for multiple compressors. i. Password access for authorised handling. j. PT-100 RTD sensor for chilled water. k. Electronic Expansion Valve. l. Anti Corrosive Treatment for Condenser.

Supply, Installation, Testing & Commissioning of Air Cooled Screw Chiller with VFD Starter complete with multiple / single Semi Hermetic Screw Compressor, Shell & Tube Condenser & Chiller Expansion Valves, First Charge of Gas R134a / R 410A & Oil etc. & unit mounted VFD. The plant should be suitable for the following parameter Capacity. Actual Capacity at Baramati Ambient Conditions. The Chillers should be installed on a baseframe along with Antivibration Spring mounted pads. Detailed Specifications as per tender Documents. The Chillers shall be made available for Factory Testing as per AHRI standards on AHRI certified Test Bed for multiple point testing. The chiller shall be AHRI / Eurovent certified. Actual Capacity 90 TR Chilled Water Inlet Temperature = 12.0 Deg.C Chilled Water Outlet Temperature = 7.0 Deg.C Air Temperature over Condenser = 40.0 Deg.C. Evaporator Fouling Factor: 0.0001 FPS. C.O.P.: Not less than 2.75. IKW/TR: Not more than 1.25 @ 100% Load. The equipment shall be complete with electrical panel and microprocessor control, with the following specifications:. a. Single Phasing Prevention. b. Under / Over Voltage Protection. c. Phase Reversal protection. d. Independent Set Points for each refrigeration ckts. e. HP / LP Trip signal interlocking. f. Interlocking for Chilled water Flow Switch. g. Auto / Manual / Test Mode facility. h. Runtime equalization for multiple compressors. i. Password access for authorised handling. j. PT-100 RTD sensor for chilled water. k. Electronic Expansion Valve. l. Anti Corrosive Treatment for Condenser.

Supply, Installation, Testing & Commissioning of Air Cooled Screw Chiller with VFD Starter complete with multiple / single Semi Hermetic Screw Compressor, Shell & Tube Condenser & Chiller Expansion Valves, First Charge of Gas R134a / R 410A & Oil etc. & unit mounted VFD. The plant should be suitable for the following parameter Capacity. Actual Capacity at Baramati Ambient Conditions. The Chillers should be installed on a baseframe along with Antivibration Spring mounted pads. Detailed Specifications as per tender Documents. The Chillers shall be made available for Factory Testing as per AHRI standards on AHRI certified Test Bed for multiple point testing. The chiller shall be AHRI / Eurovent certified. Actual Capacity 80 TR Chilled Water Inlet Temperature = 12.0 Deg.C Chilled Water Outlet Temperature = 7.0 Deg.C Air Temperature over Condenser = 40.0 Deg.C. Evaporator Fouling Factor: 0.0001 FPS. C.O.P.: Not less than 2.75. IKW/TR: Not more than 1.25 @ 100% Load. The equipment shall be complete with electrical panel and microprocessor control, with the following specifications:. a. Single Phasing Prevention. b. Under / Over Voltage Protection. c. Phase Reversal protection. d. Independent Set Points for each refrigeration ckts. e. HP / LP Trip signal interlocking. f. Interlocking for Chilled water Flow Switch. g. Auto / Manual / Test Mode facility. h. Runtime equalization for multiple compressors. i. Password access for authorised handling. j. PT-100 RTD sensor for chilled water. k. Electronic Expansion Valve. l. Anti Corrosive Treatment for Condenser.

Supply Installation Testing & Commissioning of Primary Chilled Water Pump skid with end suction pump sets (1W + 1S), each capable of delivering 320.4 USGPM of water at 18 m head. The pump skid should be supplied with 100 mm NB Butterfly Valves, Check Valve and Y Strainer. Header Size 100 mm. Weather proof Pressure & Temperature gauges. The pump should be supplied with Bronze impeller & mechanical seal. Pumps should be mounted on C section base frame with antivibration mounts in between Vibration isolators at inlet & outlet of each pumps. The skid shall be completely painted with Zinc Chromate Primer & Epoxy Paint. The Skid should be insulated with Closed cell Nitrile Rubber of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering. Only pre assembled skids, no site fabrication is allowed. We will not provide any separate foundation. Motors shall be of IE2 GRADE. The pump motor shall be suitable for 415 + 10% volts, 50 cycles, 3 phase power supply.

Supply Installation Testing & Commissioning of Primary Chilled Water Pump skid with end suction pump sets (2W + 1S), each capable of delivering 214USGPM of water at 18 m head. The pump skid should be supplied with 100 mm NB Butterfly Valves, Check Valve and Y Strainer. Header Size 125 mm. Weather proof Pressure & Temperature gauges. The pump should be supplied with Bronze impeller & mechanical seal. Pumps should be mounted on C section base frame with antivibration mounts in between Vibration isolators at inlet & outlet of each pumps. The skid shall be completely painted with Zinc Chromate Primer & Epoxy Paint. The Skid should be insulated with Closed cell Nitrile Rubber of 25 mm thickness with Chemically Treated Woven Glass Fibre Covering. Only pre assembled skids, no site fabrication is allowed. We will not provide any separate foundation. Motors shall be of IE3 GRADE. The pump motor shall be suitable for 415 + 10% volts, 50 cycles, 3 phase power supply.

Supply Installation Testing & Commissioning of Secondary Chilled Water Pump skid with end suction pump sets (1W + 1S), each capable of delivering 320.4 USGPM of water at 32 m head. The pump skid should be supplied with 100 mm NB Butterfly Valves, Check Valve and Y Strainer. Header Size 100 mm. Weather proof Pressure & Temperature gauges. The pump should be supplied with Bronze impeller & mechanical seal with VFD. Pumps should be mounted on C section base frame with antivibration mounts in between Vibration isolators at inlet & outlet of each pumps. The skid shall be completely painted with Zinc Chromate Primer & Epoxy Paint. The Skid should be suitably insulated with Closed cell Nitrile Rubber of 25mm thickness with Chemically Treated Woven Glass Fibre Covering. Only pre assembled skids, no site fabrication is allowed. No separate foundation for pumps. Motors shall be of IE2 GRADE. The pump motor shall be suitable for 415 + 10% volts, 50 cycles, 3 phase power supply.

Supply Installation Testing & Commissioning of Secondary Chilled Water Pump skid with end suction pump sets (2W + 1S), each capable of delivering 214 USGPM of water at 42 m head. The pump skid should be supplied with 100 mm NB Butterfly Valves, Check Valve and Y Strainer. Header Size 125 mm. Weather proof Pressure & Temperature gauges. The pump should be supplied with Bronze impeller & mechanical seal with VFD. Pumps should be mounted on C section base frame with antivibration mounts in between Vibration isolators at inlet & outlet of each pumps. The skid shall be completely painted with Zinc Chromate Primer & Epoxy Paint. The Skid should be suitably insulated with Closed cell Nitrile Rubber of 25mm thickness with Chemically Treated Woven Glass Fibre Covering. Only pre assembled skids, no site fabrication is allowed. No separate foundation for pumps. Motors shall be of IE3 GRADE. The pump motor shall be suitable for 415 + 10% volts, 50 cycles, 3 phase power supply.

Supply, Installation, Testing & Commissioning of Closed Expansion Tank will be of M.S. construction with interchangeable EPDM-BUTYL rubber membrane. The expansion tank shall be complete with safety relief valve and pressure gauge. The tank will be of pressure rating to suit the system pressure and will be sized to adequately compensate for water expansion due to operating temperature variations. The tank shall be fabricated as per IS 2825-1969 for “non-fired pressure vessels” and the flanges shall be as per IS 6392-1971. For chilled water application, it will be insulated with Closed Cell Nitrile Rubber Insulation Class 'O' 25 mm thickness covered with 26 G Aluminium Cladding. Inlet & Outlet Size 100 mm dia.

Supply, Installation, Testing, Commissioning of Pressurization Unit shall consist of two Nos. (1 working + 1 stand-by) high pressure pumps of suitable pressure rating mounted on M.S. frame, complete with interconnecting piping, isolation valves, NRV, Y-strainer, pressure gauge, pressure transmitter, auto-logic panel (IP55) with dry-run protection, electrical MCB and interconnecting wiring. The unit shall be housed in powder-painted canopy suitable for external installation, if required. Flow: 2 CMH, Head: 25 m Water Column.

Supply, Installation, Testing, Commissioning of The Centrifugal Air - Separator will be of M.S. construction with flanged connections. The air separator will be adequately sized to achieve maximum air-separation. It will be provided with a high capacity vent at the top with ball valve. The shell shall be fabricated as per IS 2825-1969 for “non-fired pressure vessels” and the flanges shall be as per IS 6392-1971. For chilled water application, it will be insulated with Closed Cell Nitrile Rubber Insulation Class 'O' of thickness 25 mm covered with 26 G Aluminium Cladding. Inlet & Outlet Size 100 mm dia.

Supply, Installation, Testing & Commissioning of Dirt Separators with dirt removal as well as magnetic particles using a ferro magnet upto 5 microns as per the specifications on the return water line located at the pump suction or a suitable location as suggested and suitable for water flow mentioned below. The dirt separator should have a removable flange base to allow cleaning and maintenance of the dirt separator. The separator should be complete with service valve, non return valve, butterfly valve connection for makeup water inlet, flanges, drain valve etc. Suitable for 480.6 USGPM.

Supply, installation, testing & Commissioning of 125 mm dia. M. S. Class 'C' CHILLED WATER PIPING as per IS:1239 for pipes upto 150 mm dia. & above as per IS:3529 with all structural supports along with pipe rack required with insulation of Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding.

Supply, installation, testing & Commissioning of 100 mm dia. M. S. Class 'C' CHILLED WATER PIPING as per IS:1239 for pipes upto 150 mm dia. & above as per IS:3529 with all structural supports along with pipe rack required with insulation of Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding.

Supply, installation, testing & Commissioning of 80 mm dia. M. S. Class 'C' CHILLED WATER PIPING as per IS:1239 for pipes upto 150 mm dia. & above as per IS:3529 with all structural supports along with pipe rack required with insulation of Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding.

Supply, installation, testing & Commissioning of 65 mm dia. M. S. Class 'C' CHILLED WATER PIPING as per IS:1239 for pipes upto 150 mm dia. & above as per IS:3529 with all structural supports along with pipe rack required with insulation of Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding.

Supply, installation, testing & Commissioning of 50 mm dia. M. S. Class 'C' CHILLED WATER PIPING as per IS:1239 for pipes upto 150 mm dia. & above as per IS:3529 with all structural supports along with pipe rack required with insulation of Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding.

Supply, installation, testing & Commissioning of 40 mm dia. M. S. Class 'C' CHILLED WATER PIPING as per IS:1239 for pipes upto 150 mm dia. & above as per IS:3529 with all structural supports along with pipe rack required with insulation of Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding.

Supply, installation, testing & Commissioning of 32 mm dia. M. S. Class 'C' CHILLED WATER PIPING as per IS:1239 for pipes upto 150 mm dia. & above as per IS:3529 with all structural supports along with pipe rack required with insulation of Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding.

Supply, installation, testing & Commissioning of 25 mm dia. M. S. Class 'C' CHILLED WATER PIPING as per IS:1239 for pipes upto 150 mm dia. & above as per IS:3529 with all structural supports along with pipe rack required with insulation of Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding.

Supply, Fixing & Commissioning of Valves & Gauges for Chilled Water Circuit with Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding. Butterfly Valves - 100 mm dia. PN 10.

Supply, Fixing & Commissioning of Valves & Gauges for Chilled Water Circuit with Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding. Flow Switch suitable for 100 mm dia. pipe.

Supply, Fixing & Commissioning of Valves & Gauges for Chilled Water Circuit with Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding. Pressure Independent Balancing Control Valve suitable for 320.4 USGPM.

Supply, Fixing & Commissioning of Valves & Gauges for Chilled Water Circuit with Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding. Pressure Independent Balancing Control Valve suitable for 214 USGPM.

Supply, Fixing & Commissioning of Valves & Gauges for Chilled Water Circuit with Closed Cell Nitrile Rubber Class 'O' Insulation of 25 mm thickness covered with 26 G Aluminium Cladding. Anti Vibration Bellow 100 mm.

Supply, Fixing & Commissioning of Temperature Gauges with Mercury in Glass Stem Type.

Supply, Fixing & Commissioning of Pressure Gauges SS Siphon & Gun Metal Ball valve. 150 mm dia Glycerine filled dial.

Supply, Fixing & Commissioning of Gun Metal Ball Valves Size: 25 mm Dia.

Supply, Fixing & Commissioning of Auto Air Vent.

Supply, Installation, Testing & Commissioning of Chilled Water Cassette Units complete with Cooling Coil, 4 Way Grille, Blower, Drain Pump kit. The blower shall be capable of delivering 800 CFM of air quantity. The cooling capacity of the cassette unit shall be 2.0 TR.

Supply, Installation, Testing & Commissioning of Chilled Water Cassette Units complete with Cooling Coil, 4 Way Grille, Blower, Drain Pump kit. The blower shall be capable of delivering 600 CFM of air quantity. The cooling capacity of the cassette unit shall be 1.5 TR.

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nosy strainer-1 No.,Pressure Independent Balancing Control Valve, complete with bypass line, with temp. and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber class 'O' of 25 mm thickness covered with 26 G Aluminium Cladding for following AHUs. AHU 22000 CFM

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nosy strainer-1 No.,Pressure Independent Balancing Control Valve, complete with bypass line, with temp. and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber class 'O' of 25 mm thickness covered with 26 G Aluminium Cladding for following AHUs. AHU 9000 CFM

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nosy strainer-1 No.,Pressure Independent Balancing Control Valve, complete with bypass line, with temp. and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber class 'O' of 25 mm thickness covered with 26 G Aluminium Cladding for following AHUs. AHU 7000 CFM

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nosy strainer-1 No.,Pressure Independent Balancing Control Valve, complete with bypass line, with temp. and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber class 'O' of 25 mm thickness covered with 26 G Aluminium Cladding for following AHUs. AHU 5000 CFM

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nosy strainer-1 No.,Pressure Independent Balancing Control Valve, complete with bypass line, with temp. and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber class 'O' of 25 mm thickness covered with 26 G Aluminium Cladding for following AHUs. AHU 4000 CFM

Supply, Installation, Testing & Commissioning of Readymade AHU Valve Station complete with Butterfly Valves 5 Nosy strainer-1 No.,Pressure Independent Balancing Control Valve, complete with bypass line, with temp. and pressure gauges to inlet & outlet lines, duly painted & insulated with Closed cell Nitrile Rubber Insulation of suitable thickness nitrile rubber class 'O' of 25 mm thickness covered with 26 G Aluminium Cladding for following AHUs. AHU 24000 CFM

Supply, Installation, Testing & Commissioning of Hard PVC condensate drain water piping with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell polyethylene foam. 50 mm Dia.

Supply, Installation, Testing & Commissioning of Hard PVC condensate drain water piping with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell polyethylene foam. 40 mm Dia.

Supply, Installation, Testing & Commissioning of Hard PVC condensate drain water piping with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell polyethylene foam. 32 mm Dia.

Supply, Installation, Testing & Commissioning of Hard PVC condensate drain water piping with necessary clamps, supports, hangers and fitting such as bend, tees, reducers etc. duly insulated with 9 mm thick chemically cross-linked closed cell polyethylene foam. 25 mm Dia.

Supply, Fabrication, Installation & Testing of GI Ducting Factory Fabricated with T.D.Flange as per SMACNA Class-2 with conventional supports of full Threaded GI rods of required size. All Plenums to be made out of 18 G Only. Use of 26G sheets for duct fabrication not permitted). Ducts to be properly sealed along the Joints & Flanges with approved sealant. Ducts to be tested for leakage with Smoke leakage test. Plenums to be fabricated in 18G only. No slip joints allowed.120 GSM zinc coating to consider. The quoted price shall include the cost of minor works like wall opening & closing to run the supply & return ducts. The Pressure testing of sheet metal ducts shall be carried out for complete air distribution system, The testing shall be performed before insulating the ducts as per SMACNA standards. The entire air distribution system shall be balanced to supply the air quantities as required in various zones and rooms to maintain the specified room conditions. Air Balancing of each individual supply air outlet to within +10% or -5% of the design air quantity and tabulating the same in a form of report and also the final air balancing figures shall be indicated against each measured outlets in the as built drawings. Balancing shall also include balancing of return air, supply air and outdoor fresh air quantity. Cost for air balancing before and after the client occupancy shall be considered by vendor, after client occupancy vendor shall monitor and record the air quantity at peak ambient in each terminals for a period of 15 days based on the observations vendor shall redo the air balancing as required. Calibrated air flow hoods shall be used for measuring the air flow across the square diffusers, Grill etc. and Calibrated velocity matric shall be used for measuring return air and calibrated pitot tubes with electronic controller to measure main duct airflow and static pressure. 24 G

Supply, Fabrication, Installation & Testing of GI Ducting Factory Fabricated with T.D.Flange as per SMACNA Class-2 with conventional supports of full Threaded GI rods of required size. All Plenums to be made out of 18 G Only. Use of 26G sheets for duct fabrication not permitted). Ducts to be properly sealed along the Joints & Flanges with approved sealant. Ducts to be tested for leakage with Smoke leakage test. Plenums to be fabricated in 18G only. No slip joints allowed.120 GSM zinc coating to consider. The quoted price shall include the cost of minor works like wall opening & closing to run the supply & return ducts. The Pressure testing of sheet metal ducts shall be carried out for complete air distribution system, The testing shall be performed before insulating the ducts as per SMACNA standards. The entire air distribution system shall be balanced to supply the air quantities as required in various zones and rooms to maintain the specified room conditions. Air Balancing of each individual supply air outlet to within +10% or -5% of the design air quantity and tabulating the same in a form of report and also the final air balancing figures shall be indicated against each measured outlets in the as built drawings. Balancing shall also include balancing of return air, supply air and outdoor fresh air quantity. Cost for air balancing before and after the client occupancy shall be considered by vendor, after client occupancy vendor shall monitor and record the air quantity at peak ambient in each terminals for a period of 15 days based on the observations vendor shall redo the air balancing as required. Calibrated air flow hoods shall be used for measuring the air flow across the square diffusers, Grill etc. and Calibrated velocity matric shall be used for measuring return air and calibrated pitot tubes with electronic controller to measure main duct airflow and static pressure. 22 G

Supply, Fabrication, Installation & Testing of GI Ducting Factory Fabricated with T.D.Flange as per SMACNA Class-2 with conventional supports of full Threaded GI rods of required size. All Plenums to be made out of 18 G Only. Use of 26G sheets for duct fabrication not permitted). Ducts to be properly sealed along the Joints & Flanges with approved sealant. Ducts to be tested for leakage with Smoke leakage test. Plenums to be fabricated in 18G only. No slip joints allowed.120 GSM zinc coating to consider. The quoted price shall include the cost of minor works like wall opening & closing to run the supply & return ducts. The Pressure testing of sheet metal ducts shall be carried out for complete air distribution system, The testing shall be performed before insulating the ducts as per SMACNA standards. The entire air distribution system shall be balanced to supply the air quantities as required in various zones and rooms to maintain the specified room conditions. Air Balancing of each individual supply air outlet to within +10% or -5% of the design air quantity and tabulating the same in a form of report and also the final air balancing figures shall be indicated against each measured outlets in the as built drawings. Balancing shall also include balancing of return air, supply air and outdoor fresh air quantity. Cost for air balancing before and after the client occupancy shall be considered by vendor, after client occupancy vendor shall monitor and record the air quantity at peak ambient in each terminals for a period of 15 days based on the observations vendor shall redo the air balancing as required. Calibrated air flow hoods shall be used for measuring the air flow across the square diffusers, Grill etc. and Calibrated velocity matric shall be used for measuring return air and calibrated pitot tubes with electronic controller to measure main duct airflow and static pressure. 20 G

Supply, Fabrication, Installation & Testing of GI Ducting Factory Fabricated with T.D.Flange as per SMACNA Class-2 with conventional supports of full Threaded GI rods of required size. All Plenums to be made out of 18 G Only. Use of 26G sheets for duct fabrication not permitted). Ducts to be properly sealed along the Joints & Flanges with approved sealant. Ducts to be tested for leakage with Smoke leakage test. Plenums to be fabricated in 18G only. No slip joints allowed.120 GSM zinc coating to consider. The quoted price shall include the cost of minor works like wall opening & closing to run the supply & return ducts. The Pressure testing of sheet metal ducts shall be carried out for complete air distribution system, The testing shall be performed before insulating the ducts as per SMACNA standards. The entire air distribution system shall be balanced to supply the air quantities as required in various zones and rooms to maintain the specified room conditions. Air Balancing of each individual supply air outlet to within +10% or -5% of the design air quantity and tabulating the same in a form of report and also the final air balancing figures shall be indicated against each measured outlets in the as built drawings. Balancing shall also include balancing of return air, supply air and outdoor fresh air quantity. Cost for air balancing before and after the client occupancy shall be considered by vendor, after client occupancy vendor shall monitor and record the air quantity at peak ambient in each terminals for a period of 15 days based on the observations vendor shall redo the air balancing as required. Calibrated air flow hoods shall be used for measuring the air flow across the square diffusers, Grill etc. and Calibrated velocity matric shall be used for measuring return air and calibrated pitot tubes with electronic controller to measure main duct airflow and static pressure. 18 G

Supply and Installation of washable, inherent and permanent fire retardant type fabric air dispersion ducting system. Fabric air dispersion system shall be made of 100% inherent and permanent fire retardant polyester and shall have a flame spread and smoke developed index satisfying Class 1 rating in accordance with ASTM E 84 of NFPA 90-A testing Standard and shall also have a fire propagation index (I) of less than 12 and first index score of less than 6 satisfying Class ‘O’ rating in accordance with BS 476: Part 6: 1989+A1: 2009 testing standard. Permeability of fabric ducts should be less than 0.5 cfm/ft2 (at 120Pa pressure). Fabric duct system should be complete with all attachments (straights, bends, endcaps, Tee's, reducers), suspension fittings, laser cutting orifices for air dispersion, pressure adjustment device and airflow control device as per manufacturers standards. The item should also include necessary mounting arrangement alongwith necessary runs of gripple wire and clamping arrangements and secondary supports neatly clamped to the existing structure etc. complete. Diameter 850 mm

Supply and Installation of washable, inherent and permanent fire retardant type fabric air dispersion ducting system. Fabric air dispersion system shall be made of 100% inherent and permanent fire retardant polyester and shall have a flame spread and smoke developed index satisfying Class 1 rating in accordance with ASTM E 84 of NFPA 90-A testing Standard and shall also have a fire propagation index (I) of less than 12 and first index score of less than 6 satisfying Class ‘O’ rating in accordance with BS 476: Part 6: 1989+A1: 2009 testing standard. Permeability of fabric ducts should be less than 0.5 cfm/ft2 (at 120Pa pressure). Fabric duct system should be complete with all attachments (straights, bends, endcaps, Tee's, reducers), suspension fittings, laser cutting orifices for air dispersion, pressure adjustment device and airflow control device as per manufacturers standards. The item should also include necessary mounting arrangement alongwith necessary runs of gripple wire and clamping arrangements and secondary supports neatly clamped to the existing structure etc. complete. Diameter 600 mm

Al. Louvers for Fresh Air / Exhaust Supply, installation, testing & commissioning of Fresh Air / Exhaust Air Louvers - constructed in Extruded Aluminium Anodised finish. Blades inclined at 45deg. on 40mm pitch complete with:Minimum Measerable unit 0.1 Sq.mt.a) Sheet steel enclosure cowl b) Opposed Blade Volume Control Damper c) Bird wire guard in galvanised steel with front flanged frame

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 2000 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 750 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 1600 CFM (Fresh Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 500 CFM (Fresh Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 450 CFM (Fresh Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 350 CFM (Fresh Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 250 CFM (Fresh Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 200 CFM (Fresh Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 150 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 200 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 250 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 300 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 350 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 450 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 500 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 600 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 700 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 900 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Cabinet Type Inline Fans with DIDW forward curved impeller fitted with maintenance free motor with EU – 4 Filter, confirming to technical specifications provided with the tender. Including double canvass connection (fire retardant). The fan shall have low sound level not exceeding 40 DBA at three meter distance. Only Fresh Air fans to be provided with filters. 1000 CFM (Exhaust Air Fan)

Supply, Installation, Testing & Commissioning of Acoustic Insulation of Duct with 19 mm thick Open Cell Nitrile Rubber with Anti Microbial Treatment & of Class '1' stuck inside the duct using rubber adhesives. Density of 140 - 180 Kg/m3.

Supply, Installation, Testing & Commissioning of Underdeck Roof insulation with 19 mm thick Nitrile rubber insulation with Aluminium foil on one side.

Supply, Installation, Testing & Commissioning of 100 mm dia Preinsulated flexible duct with end clamps and Aluminium foil on both side as required in various sizes as below. The duct shall fire retardant UL standard approved.

Supply, Installation, Testing & Commissioning of Aluminium powder coated Non Vision Type Louvers.

Supply, Installation, Testing & Commissioning of UV Coating For Exposed Copper Pipes to Atmosphere. Piping insulation to be covered with Woven Glass Cloth 100 gsm and finished in U/V Treatment.

Supply & Top of Additional Refrigerant R410A for VRV / VRF System as per Manufacturer requirement.

Supply,Installation,Testing & Commissioning of All side Flanged Grille made out Extruded Aluminium duly powder coated of following size: Grille: 600 x 600

Supply, Installation, Testing & Commissioning of All side Flanged Grille made out Extruded Aluminium duly powder coated of following size:150X150

Supply, Installation, Testing & Commissioning of Aluminium powder coated long jet nozzles capable of delivering with VCD. 400 mm Dia.

Supply,Installation,Testing & Commissioning of 150 mm Disc Valve. PVC / HDPE Material Only. (Ordering by HVAC vendor only after Approval of Technical Specifications & Colour shade of Physical sample by Consultant & Architect).

Supply, Installation, Testing & Commissioning of hi capacity drain pumps for Hiwall units.

Supply, Installation, Testing and Commissioning of Air Cleaning Equipment Dry Scrubber confirming Following & as per specification. Construction: Made of 16 gauge galvanized sheet, high bake epoxy powder coated or 2 mm mild steel plate oil proof of IP 54. The unit shall have energy efficient (IE3) Motor. Pre Filter: Washable type aluminium mesh pre-filter. Collector Plate: High grade Aluminium collector plates which should be alternatively charged positive & negative with large collecting area. Collector cell should be of permanent type and slide out facility for easy removal for cleaning. Insulator: PTFE or Ceramic Insulator. Access door to filter section shall be equipped with safety limit switch. Oil outlet ½’’ shall be provided at under side (when fitted horizontal) Capacity of the Exhaust 20000 CFM

Supply, Installation, Testing & Commissioning of Double Skin Evaporative Cooling Unit complete with MS base frame, fan section, wet section & filter section. The unit shall have its own sump & frame. The sump shall be of 1.6mm thick SS 304 construction. 300 mm thick cellulose cooling pad, 10 micron HDPE filters & 4 Pass PVC Mist Eliminators. The unit shall be capable of delivering following Air Quantity. The colour of the unit shall be confirmed as per the client's requirement. The unit shall have energy efficient (IE3) Motor. 18000 CFM

Supply, Installation, Testing & Commissioning of Hard UPVC supply water piping using plumbing grade UPVC pipes. The piping shall be properly clamped using saddle & pressure clamps. (50 mm Dia)

Supply, Installation, Testing & Commissioning of Hard UPVC supply water piping using plumbing grade UPVC pipes. The piping shall be properly clamped using saddle & pressure clamps. (32 mm Dia)

Supply, Installation, Testing & Commissioning of cast brass ball valves chrome plated ball inside and hard chrome plated ball PTFE (Teflon) seal and ring and chrome plated steel centre handle with female BSP threads as directed by the Engineer-in-Charge .including all taxes, for all leads and lifts, testing etc. complete. (Prior approval of sample and brand by Ex.Engineer is necessary before use.) 25 mm dia.

Supply, Installation, Testing & Commissioning of Pressure Balancing valve suitable for 50mm Dia pipe so as to maintain 1kG pressure in the line

Supply Installation Testing & Commissioning of Exposed duct insulation with 19 mm thick nitrile rubber and externally covered with 26 gauge aluminium cladding for all leads and lifts.

Chhatrapati Shivaji Maharaj Statue with Meghdambari and Ornamentations: Detailed Thematic Designing, planning, Providing and fixing, fabricating, erecting, and installing, and handing over of said work as per approved design, drawing & dimensions. he statue shall be created with Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt.The work is divided in FOUR stages: Clay & Structure: (Work Weightage - 45%) The cladding will be created by using clay mould method, as referred in the approved drawings. Moulding & Production: (Work Weightage - 35%) Composite synthetic polymers and glasswool shall be used in 3 layers for casting moulds and dyes for production with spray treatment of COT100. Fabrication, Installation and Coloring (Work Weightage - 15%) The fabrication work shall be done by using MS coiled pipes of 14 to 16 gauge as per requirement and in 1" to 2" of sections with anti rust coatings (SMAC RCCP - 120) in TWO layers, Colouring & Finishing in bronze texture. The entire art work, once installed, shall be painted with combination of branded water based exterior emulation and oil based auto colours and finishing touch. including all labour, Material, all leads and lifts, with Transportation,including all necessarry Scaffolding etc, complete. Commissioning (Work Weightage - 5%). To be executed as directed by Engineer in Charge.

Entry Gate for Zones: Detailed Thematic Designing ,planning ,Providing and fixing, fabricating, erecting, and installing, commissioning testing and handing over as the said work per approved design, drawing & dimensions. The Entry Gate shall be created with Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The entire cladding work is divided in FOUR stages: Clay & Structure: (Work Weightage - 45%) The cladding will be created by using clay mould method, as referred in the approved drawings. Moulding & Production: (Work Weightage - 35%) Composite synthetic polymers and glasswool will be used in 3 layers for casting moulds and dyes for production with spray treatment of COT100. Fabrication, Installation and Coloring (Work Weightage - 15%) The fabrication work will be done by using MS coiled pipes of 14 to 16 gauge as per requirement and in 1" to 2" of sections with anti rust coatings (SMAC RCCP - 120) in TWO layers, Colouring & Finishing in stone texture.: The entire art work, once installed, will be painted with combination of branded water based exterior emulation and oil based auto colours and finishing touch. including all labour ,Material,all leads and lifts,with Transportation,including all necessarry Scaffolding etc,complete. Commissioning (Work Weightage - 5%). To be executed as directed by Engineer in Charge.

Theming: with upto 4 inches relief work. Detailed Thematic Designing ,planning ,Providing and fixing, fabricating, errecting, and installing, commissioning testing and handing over as the said work per approved design, drawing & dimensions. All the theming work shall be created with Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt.The entire cladding work is divided in FOUR stages: Clay & Structure: (Work Weightage - 45%) The cladding will be created by using clay mould method, as referred in the approved drawings. Moulding & Production: (Work Weightage - 35%) Composite synthetic polymers and glasswool will be used in 3 layers for casting moulds and dyes for production with spray treatment of COT100. Fabrication, Installation and Coloring (Work Weightage - 15%) The fabrication work will be done by using MS coiled pipes of 14 to 16 gauge as per requirement and in 1" to 2" of sections with anti rust coatings (SMAC RCCP - 120) in TWO layers, Colouring & Finishing: The entire art work, once installed, will be painted with combination of branded water based exterior emulation and oil based auto colours and finishing touch. including all labour ,Material,all leads and lifts,with Transportation,including all necessarry Scaffolding etc,complete. Commissioning (Work Weightage - 5%). To be executed as directed by Engineer in Charge.

Props: Detailed Designing, creating and installation of Exact replicas of Tents, Bunkers, Rocks, Guns, Ammunitium, Boxes, Cannons, swords, Javelins, Thrones, Shields, and other historical weapons and artifacts used by the Maratha, Moghuls dynasty including required tapestry as per approved artwork. All the props shall be created in either entirely or in appropriate combination of FRP, metal, glass, wood, ornamental stones, cloth, tapestry & plastic. Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The entire art work, once installed, shall be painted with combination of branded water based exterior emulation and oil based auto colours and finishing touch. including all labour ,Material,all leads and lifts,with Transportation,including all necessarry Scaffolding etc,complete. As directed by Engineer-In-Charge.

Static Statue - Type - A To provide Life Like, Wax Finsh statues of Prominent Characters related to the concept with real clothes, hair and proper makeup with artificial jewellery of appropriate scale suitable to scene as per approved references. The base material for the statues shall be FRP. Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The process is to photograph good actors with appropriate expressions as references as the statues are supposed to look life like. As directed by Enginer-In-Charge.

Static Statue - Type - B To provide Life Like, Wax Finsh statues of General Catagorey Characters of soldiers, & villagers related to the concept with real clothes, hair and proper makeup. In appropriate scale suitable to scene as per approved references. The base material for the statues shall be FRP. Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The process is to photograph good actors with appropriate expressions as references as the statues are supposed to look life like. As directed by Enginer-In-Charge.

Static Statue - Animals - Horse, Bullock: To provide Life Like, Wax Finsh statues with necessary riding accessories with appropriate scale suitable to scene as per approved references. The base material for the statues shall be FRP. Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The process is to photograph good actors with appropriate postures as references as the statues are supposed to look life like.Wax Finsh statues with necessary riding accessories with appropriate scale suitable to scene as per approved references. As directed by Enginer-In-Charge.

Static Statue - Animals - Camel To provide Life Like, Wax Finsh statues with necessary riding accessories with appropriate scale suitable to scene as per approved references. The base material for the statues shall be FRP. Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The process is to photograph good actors with appropriate expressions as references as the statues are supposed to look life like. Wax Finsh statues with necessary riding accessories with appropriate scale suitable to scene as per approved references. As directed by Enginer-In-Charge.

Static Statue - Animals - Elephant To provide Life Like, Wax Finsh statues related to the concept with real accessories and clothes, of appropriate scale suitable to scene as per approved references. The base material for the statues shall be FRP. Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The process is to photograph animals with appropriate postures as references as the statues are supposed to look life like.To provide Life Like, Wax Finsh statues with necessary riding accessories with appropriate scale suitable to scene as per approved references. As directed by Enginer-In-Charge.

Animatronic Statue - Animals - Elephant To provide Life Like, Wax Finsh statues related to the concept with real accessories and clothes, of appropriate scale suitable to scene as per approved references. The statues of elephants shall be rigged with robotic technology. The elephants shall, thus be able to make realistic movments of eyes, trunk, mouth, ears, breathing and tail. The enitre robotic animal shall run on electricity as with the pre-programmed motion cycles, designed according to the script. The base material for the statues shall be soft silicon and FRP.Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The process is to photograph animals with appropriate postures as references as the statues are supposed to look life like.To provide Life Like, Wax Finsh statues with necessary riding accessories with appropriate scale suitable to scene as per approved references. As directed by Enginer-In-Charge.

Semi Robotic Statue - To provide Life Like, Wax Finsh statues of prominent characters related to the concept with real clothes, hair and proper makeup with artificial jewellery of appropriate scale suitable to scene as per approved references. The statues shall be rigged with robotic technology. They shall, thus be able to make realistic movments of eyes, mouth, neck & hands. The enitre robotic statue shall run on electricity as with the pre-programmed motion cycles, designed according to the script.The base material for the statues shall be FRP. Fiber Reinforce Polymers (FRP). Fibre-reinforced polymers (FRP; also called fibre-reinforced plastics) is a composite material made of a polymer matrix reinforced with fibres. The fibres are usually glass (in fibreglass), carbon (in carbon-fibre-reinforced polymer), aramid, or basalt. The process is to photograph good actors with appropriate expressions as references as the statues are supposed to look life like. As directed by Enginer-In-Charge.

Media Production: This is a multi track media production to create an experience of historical happenings in the times of Chatrapati Shivaji Maharaj. The recordings will employ considerable amount of sound design with appropriate sound effects, acostic music and dramatisation of voice track as well as audio voice over commentroy. The entire media shall be mixed in 5.1 configuration according to the approved script. As directed by Enginer-In-Charge.

Media Production: AV to be used in special attraction presentation like 270 degree projection, Dual or Triple blended projections or of odd shaped projections required according to the approved script & scene.The media production shall be done in Full HD 1920/1080 format with CG, VFX, Shooting, Compositing, and Post Production with Sound Dubbing. Shooting : Live + Chroma (Green screen) , Editing, Special Effect - VFX with 3D modeling, Rigging, lighting, animation and texturing with Compositing, Dubbing, Music & Background Score and sound effects, 5.1 Surround Sound Mixing at Site, Special Effect Design, Programming, Testing and Debugging. As directed by Engineer-In-Charge.

Media Production - Type - A: Mapping : Creating a specialized media in full HD 1920/1080 format with CG, shooting, compositing, and post production with sound dubbing suitable for projecting and mapping on uneven surfaces of the miniature models.

Media Production - Type - B - Stereoscopy Simulation - High Version: To create & provide media in LEFT & RIGHT format in Full HD 1920/1080, CG, VFX, Shooting, Compositing, and Post Production with Sound Dubbing. Shooting : Live + Chroma (Green screen) Shooting will be done, Editing, Special Effect - VFX with 3D modeling, Rigging and texturing with Compositing, Dubbing, Music & Background Score, 5.1 Surround Sound Mixing at Site, Special Effect Design, Programming and synchronizing with simulation equipment, Testing and Debugging complete.

Media Production - Type - C - Setreoscopic - Small Version: To create & provide media in Full HD 1920/1080 format, CG, VFX, Shooting, Compositing, and Post Production with Sound Dubbing. Shooting : Live + Chroma (Green screen) Shooting will be done, Editing, Special Effect - VFX with 3D modeling, Rigging and texturing with Compositing, Dubbing, Music & Background Score, 5.1 Surround Sound Mixing at Site, Special Effect Design, Programming, Testing and Debugging.

Projector - Type - A To provide, install, map, test and commission the 4000-5000 Lumens Projectors with ST or UST fittings with onsite resizing of Media suitable to Projection area. The preferred makes are BenQ / Optoma / EPSON / Panasonic or equivalent

Projector - Type - B To provide, install, map, test and commission the 18000-20000 Lumens Projectors with Standard Lens of Panasonic PT - RZ21K with LE6/Barco HDX W20 Flex / Christie WU 20K-J or equivalent with onsite resizing of Media suitable to Projection area.

Projector - Medium (8.5k lumens): SITC of 8500 Lumens Projectors. 1-Chip DLP Projection system with Standard Lens of Panasonic /Benq/ Optoma or equivalent with onsite resizing of Media suitable to Projection area.

Projector - High (10k lumens) : SITC of 10000 Lumens Projectors. 1-Chip DLP Projection system with Standard Lens of Panasonic /Benq/ Optoma or equivalent with onsite resizing of Media suitable to Projection area.

LCD Panel: To provide, install, synchronize, test and commission the 65 inches LCD Panels with proper connection to the main server including necessary cabling and required accessories. Make-Panasonic, LG, Samsung or equivalent with onsite resizing of Media suitable to display area.

LED Wall in surround Configuration: To provide, install, synchronize, test and commission the P5 Active LED Wall in surround configuration and blending with proper connection to the main server including necessary cabling and required accessories. Pixel pitch, Brightness-1400cd/m2, Min. viewing distance 6 mtrs., Cabinate diamension 1152x 960mm Make - Panasonic, LG, Sunrise, Logic or equivalent with onsite resizing of Media suitable to display area and programmed with the master playback server.

Sound: Small To provide, install, synchronize, test & commission the 5.1 surround sound system, comprising of Center Speaker 40Hz-150Hz with BASS reflex, Front Speaker with BASS reflex, 10ohms, 80mm Cone Type. Make-SONY / Yamaha or equivalent.

Sound: Medium To provide, install, synchronize, test & commission the 5.1 surround sound system, comprising of LCR- 3-way, Bi-ampled Powered Speaker, Bass-reflex, Frequency Range (-10dB) 31Hz - 20kHz, Maximum Output Level (1m; on axis) 143dB SPL., Sorround speakers- Power rating: 700W, max SPL: 125dB, Frequency range: 48Hz -20Khz, sub woofer- Powered sub woofer with bass reflex, Frequency range ( -10dB) 30Hz – 150 Hz, Maximum output level (1m on axis) 136dB SPL, Amplifier - Class D, Balanced output circuit (BTL) , with Output Power (1kHz Non-clip 20msec Burst ) : 8 Ohms 500W X 2, Frequency Response: ±1.0dB (1W, 8Ω, 20Hz to 20kHz). and AVR -11.2Ch 8K Ultra HD AV Surround Pre-Amplifier with HEOS® Built-in and Voice Control Featuring 11.2 channel XLR and RCA pre-outs, supporting all 3D audio formats including Dolby Atmos®, Dolby Atmos Height Virtualization, DTS:X®, DTS Virtual:X™, IMAX Enhanced®, and Auro-3D.along with all the required accessories to synchronize with Show control. Make - BOSE/JBL/SONY/Electro Voice/ YAMAHA or equivalent.

Sound: Special To design, provide, install, synchronize, test & commission with onsite sound mixing of the 5.1 surround sound system, comprising of Main L-C-R, with IL -IR: M/HF - frequency response (-3DB): 40Hz-19KHz, LF:800w, M/HF-300w, Normal impedance: 12Ohms x 5 nos., LF for Main L-C-R, with IL -IR: frequency range:30Hz-20KHz, sensitivity-115DB with systeme input power rating-LF:1200w, MF:700w, HF:150w x 5 nos., Subwoofers: 40Hz-100Hz, 100DB, 1w @1m, maximum impedance:4Ohms, input power handelling-950w x 10 nos., Surrounds (6-12-6): Frequency range (-10DB):50Hz-25KHz and 60Hz - 25KHz, rated impdance-8Ohms x 24 nos., with required all accessories for installation., Cinema Audio Processor 7.1 Format: Digital input:impedance 100Ohms @0.5-10Vpp, Analog output: Impedance 30Ohms (Balanced), frequency response:20Hz-20KHz x 1 no.,with Audio Processor: 1 no., Analog IN Card x 3 no., Analog OUT x 1 no., BOB x 1 no. Make - JBL / YAMAHA / BOSE / EV or equivalent.

Sound - Theatrical 7.1 Surround Sound: SITC of Sound Equipment - Detailed Designing, planing, providing, fixing, positioning of 7.1 Surround Sound System – Pro Audio System, EV ELX-115, 112, 118P/ JBL SRX 815,812,828 with AV Processor-Marantz SR 5013 and Amplifier-AMB-600, AMB-1200, AMB-1600, SRT-4200/ EV Q99, EV Q1212/ CROWN 900HD, 2400-N with 32 U Rack alongwith Onsite Installation of audio equipment and On Site Sound Mixing. Make - JBL / YAMAHA / EV or equivalent.

Show Lights: Detailed Designing, planning, and providing, fixing, positioning, Synchronizing, testing & commissioning of Show lights Boxer - k2D068 / S008 – 3 x 54 RGBW LED PAR S101 – 3 x 54 RGBW LED PAR OR Mini Moving Head / 7R Sharpy / 10R Sharpy / DMX Splitters 8-12 Channels or equivalent, with Creative programming, color combination, movements, strobes and other light effects at site according to the story of the attraction. Make - stan/Canara/Big dipper/LBT or equivalent.

Synchronus Media Player with TC Control: To provide, install & commissioning of dedicated synchronizable (in Master Slave Configuration) Media Player unit capable of FULL HD 1920 x 1080 video playback- comprising of Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz, 2GB, LPDDR4-3200 SDRAM (depending on model), 2.4 GHz and 5.0 GHz IEEE 802.11ac wireless, Bluetooth 5.0, BLE, Gigabit Ethernet, 2 USB 3.0 ports; 2 USB 2.0 ports., 2 HDMI ports (up to 4kp60 supported, 2-lane MIPI DSI display port, 2-lane MIPI CSI camera port, 4-pole stereo audio and composite video port, H.265 (4kp60 decode), H264 (1080p60 decode, 1080p30 encode), OpenGL ES 3.1, Vulkan 1.0, Micro-SD card slot for loading operating system and data storage, Power over Ethernet (PoE) enabled (requires separate PoE HAT), Operating temperature: 0 – 50 degrees C ambient. Sync signal INPUT through Ethernet . Digital Inputs : 5 potential free contacts( 12 Volt Tolerant ), Digital Outputs : 5 ( To control external Relays with isolated ground), Operating System: Linux, Power Supply : 230VAC, 50 Hz, Power Consumption: 10 W. Make- GME/Alcon-McBright or equivalent

Show Control: To provide, install & commissioning of show control unit - SPD2101 with capability of synchronizing muliple devices. Precision sync with SMPTE standard including Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz, 2GB, LPDDR4-3200 SDRAM (depending on model, 2.4 GHz and 5.0 GHz IEEE 802.11ac wireless, Bluetooth 5.0, BLE Gigabit Ethernet, 2 USB 3.0 ports; 2 USB 2.0 ports, 2 HDMI ports (up to 4kp60 supported), 2-lane MIPI DSI display port, 2-lane MIPI CSI camera port, 4-pole stereo audio and composite video port, H.265 (4kp60 decode), H264 (1080p60 decode, 1080p30 encode), OpenGL ES 3.1, Vulkan 1.0, Micro-SD card slot for loading operating system and data storage, Power over Ethernet (PoE) enabled (requires separate PoE HAT), Operating temperature: 0 – 50 degrees C ambient. Custom built dedicated hardware & software device, easy to use with out board control panel. Sync signal through Ethernet to control all slave units . Digital Inputs : 5 Potential free contacts (To control Start Stop of Show), Digital Outputs : 5 ( To control external Relays with isolated ground) , Operating System: Linux, Power Supply : 230VAC, 50 Hz, Power Consumption: 10 W, Mechanical Dimensions: 2 U 19 inch Rack.

DMX Recorder & Control: To provide, install & commissioning of DMX Recorder & Control unit - PMN2103 with capability of recording 4 Universes Real Time and ability to work with any lighting board, including Broadcom BCM2711, Quad core Cortex-A72 (ARM v8) 64-bit SoC @ 1.5GHz, 2GB, LPDDR4-3200 SDRAM (depending on model, 2.4 GHz and 5.0 GHz IEEE 802.11ac wireless, Bluetooth 5.0, BLE Gigabit Ethernet, 2 USB 3.0 ports; 2 USB 2.0 ports, H.265 (4kp60 decode), H264 (1080p60 decode, 1080p30 encode), OpenGL ES 3.1, Vulkan 1.0, Micro-SD card slot for loading operating system and data storage, Power over Ethernet (PoE) enabled (requires separate PoE HAT), Operating temperature: 0 – 50 degrees C ambient. Storage capacity of about 50 hours of playback. Sync signal through Ethernet to control all slave units . Digital Inputs: 5 potential free contacts( 12 Volt Tolerant., DMX OUT : 1 Universe(512), DMX time line program is accepted through Ethernet from another PC through QLC, Operating System: Linux, Power Supply: 230VAC, 50 Hz, Power Consumption: 10 W, Mechanical Dimensions: 2 U 19 inch Rack

Onsite Show Mapping Produciton-1 Creation of final show with minute geomatric corrections of the Full HD videos (upto 2 videos) according to the special requirements of the varied surfaces of the approved scene. 'Mapping' is fitting the desired videos on the odd shaped surface areas geometrically. These may be building facades or indoor areas and part of the attractiions. Shivsrushti is using many miniature models, dark ride and odd shaped, more than 60 degrees projections. These will need extremely good quality mapping to create the desired dynamic motion effects. Highly specialised softwares like MAD MAPPING, GREEN RHINOS shall be usd for precision mapping results. The process is extremely complicated as the geometry is reshaped at pixel level. As directed by Engineer-In-Charge.

Onsite Show Mapping Produciton-2 Creation of final show with minute geomatric corrections of the Full HD videos (upto 10 videos) according to the special requirements of the varied surfaces of the approved scene. 'Mapping' is fitting the desired videos on the odd shaped surface areas geometrically. These may be building facades or indoor areas and part of the attractiions. Shivsrushti is using many miniature models, dark ride and odd shaped, more than 60 degrees projections. These will need extremely good quality mapping to create the desired dynamic motion effects. Highly specialised softwares like MAD MAPPING, GREEN RHINOS shall be usd for precision mapping results. The process is extremely complicated as the geometry is reshaped at pixel level. As directed by Engineer-In-Charge.

Onsite Integration: Desigining, Equipment Installation with Light Controls (Upto 60 Lights), Media Control (per Projection), Special Effect Control, Show Control, Accessories etc complete - To provide, install and program Show Director SX-0001 / TrueLive HD-933 / iLitStream DX – 2009 / QuickSense – DI2166 / QuickR – DO2216 Multi-protocol architectural lighting controller with DMX Interface Cinema Server with HD Playback GPIO Interface Module with RS 232 port, DMX-512 port supporting ethernet based protocols Show control unit with Time Code Master, Slave supporting UDP, TCP, OST and MIDI Protocols Show control unit with Time Code Master, Slave supporting UDP, TCP, OST and MIDI Protocols with onsite Installation of Integration Equipments. The Show Control Unit is a combination of above mentioned equipments as per Technical Requirements of particular Scene. As directed by Engineer-In-Charge.

Show Projection Screen: (100 feet x 24 feet) with Mechanism Motorized winding and unwinding unit with Tension Controller for Screen including Main Axial Drum System with Interface and Support System for free rotary motion and Sturdiness. Linear Winding Mechanism with Pulling Ropes and Hooks & Rubberized Rotary Support for Full Length with support structure. Frame Structure with Rope Anchoring Support Top (Screen) Full Length. Screen Bottom Support to Interface with Tension Controllers & Control Panel. Make -Customized - Mechanisum with 10HP MOTOR WITH REDUCTION GEAR BOX. MOTOR : Total 10HP : Hindustan / CG / Rotomotive or Equivalent. Gear Box : Bonfiglioli / Rotomotive / Equivalent Mechanisum : Rotary mechanism, full screen Length, Motor Drive Controller (speed) Indications : Technik / Equivalent Switches : Technik / Equivalent MCB : Polycab / Equivalent. Drive : Fuji / ABB / Delta or Equivalent Wires : Polycab / RR Cable or Equivalent. Contactor : CG / Havells / L&T or Equivalent Panel Screen: FP XL MESH for constant gain. Make - Showtex / Crystal / Veron or equivalent. As directed by Engineer-In-Charge.

Miniature Model - High - Detailings (up to 3 feet contour): Detailed Thematic Designing, planning, Providing and fixing, fabricating, erecting, and installing, and handing over of said work of a scaled miniature model of a building or a terrain created with all the detailings of existing contours, topography, structural elements in a proportional scale suitable to the display venue but not exceeding the height of 3'-0". This model is made in a mix material meduim like FRP, wood pulp, POP clay or Foam sheet as per the required details and the type of media to be projected on it as directed by site incharge.

Paintings: Detailed thematic desining, sketching, colouring, finishing & installating of paintings as per approved concept. The artwork will be painted with a combination of branded water based exterior emulsion and acrylic colours. The approved artwork to be enlarged and printed on a larger size of 12 x 18 ft., using digital printing technology and fixed on a permanent structrue in wooden or MS Frame of the appropriate size.

Cutouts: Detailed designing, creating & installation of cutouts made in 4 mm foam sheet of maximum size of 6 feet high and 2 feet wide in proportion to the human scale supported with MS fabricated stand.

Holography Setup: SITC of customized holography setup to give a feel of mid air projection. The set up of 15 feet wide and 30 feet length to be created using 3D holographic technology with all the necessary rigs and fitments as per the international standards. The technology uses petented silver foile coated transperent surface with above 99.91% opacity with sufficiantly lit background and foreground objects to create a mid air floating image. The loss of brightness due to surface is compensated by high luminance projections and ultra short thow lenses. As direcetd by Engineer-In-Charge.

Chair Simulation Setup: SITC of 96 seat simulation equipment assembly with Pneumatic motion system. The system will work with pneumatic actuator bore 80 strokes 75 and needs to support the ssure of 8 bar. The air distribution system will be with solenoid valve bi-stable ¼ inch. The complete system will work with fast couplings and pressure regulator. The Pneumatic motion system used will be of JANATICS/FESTO. Chairs - The chairs used for the 7D Cinema are sport chairs structured on a steel base and the cushions are built with specific foam and covered with black and grey leatherette. Measurements 31 Inch * 21 Inch. Special effects included on/in chair. The chairsshould have 3 special effects included, namely: water spray, air spray and leg ticklers. The special effects on the chairswill work with solenoid valve mono-stable and will be able to support a maximum pressure of 10 bar - this pressure will be controllable which can be regulated separately from movement system. Sensor of Linear Position The linear position sensor will work from 0 to 5volts.Should have capability to read 5(Five) different spatial position. Compressor – 3 Oil injected screw compressor. working pressure 10 bar g - 145 psi g and Min. working pressure 5 bar g - 72.5 psi g. Maximum power consumption needs to be 11 kW - 15Hp and needs to have 3 Reserve Air Tanks having a capacity of 500 liters each. The compressor used will be of ELGI/CHICAGO make. Electrical Panel. The system will work with 400-volt tri-phase and 220-volt mono-phase. Max. power consumption should be50 kw hour. Every electrical line will have a dedicated breaker switch to protect the system. The master line willbe protected with differential breaker switch. All electrical fittings will be as per ISI or CE standard. PLC (drive and synchronize system). The PLCs will be able to work in low tension 24-volt dc. The PLCs will have the capability to drive movement and multiple special effects. PLC should be capable of readinglinear sensor of position and drive of 16 different special effects. The PLC used will be a custom build PLC as per the requirement of the system. Special Effects in the room The 7d cinema must have 5 special effects namely: wind, thunder, bubbles smog, aroma. Wind machine mentioned above should consist of Blade diameter of 390 MM, a flow rate of 128 m3-min and static pressure of 400 Pa, voltage 220 v, an frequency of 50Hz, power usage of 1500 Watts and speed of 2900 r\min. The make of the blower used as special effects will be Star brand and will have 1 HP each. As direcetd by Engineer-In-Charge.

Simulation Platform with 9D Effects: SITC of customized High- Tech simulation platform System with, Modules of 48 seats, Fluid dynamic movements, Variable,Linear Position Servo Driver, Operating pressure 9/13 bar, Silent Compressor, Air Collecting cylinders 500 lts. 15Hp, Feet Ticklers, Air Spray, water Spray, Tornado (Wind) effects, Bubble effects, fog effect, Lightining effect as directed by site incharge.

Polarizer: SITC of 3D modulator supporting DLP projection up to 32k lumens lamp power silver screen of 2.4 gain & active surface size of 171 x 116 mm. Make - Volfoni / DepthQ / Expand OR equivalent.

Screen Silver - Special Projection: SITC of customized perforated silver screen of above 2.4 gain suitable for 3D streoscopic film as per required size and specifications along with the framed support structure. Make - Veron / Crystal or equivalent.

3D Passive Glasses: SITC of passive 3D glasses suitable for giving 3D visual effect. Make - DepthQ / Expand or equivalent.

Fountain Assembly: SITC of “Outside drop” ring of 2.5 metre dia having brass ball nozzles with jet height of 3 metre with galvanized manifold and supporting stands and suitable mono submersible pump (Kirloskar) of suitable head & discharge with suction mesh cover and control panel as per approved designs.

Seating Arrangement: Providing and fixing of customized seating arrangement with a capacity of 80 persons made in a 3 seat modular form using MS framed structure and teak wood with PU coat.

Outdoor Scultpure: Detailed Thematic Designing, planning, Providing and fixing, fabricating, erecting, and installing and handing over the scenic work of 3 dimensional sculpture of 8 metre wide and 10 metre length with proportional height. The entire cladding work is divided in FOUR stages: Clay & Structure: (Work Weightage - 45%) The cladding will be created by using clay mould method, as referred in the approved drawings. Moulding & Production: (Work Weightage - 35%) Composite synthetic polymers and glass wool will be used in 3 layers for casting moulds and dyes for production with spray treatment of COT100. Fabrication, Installation and Colouring (Work Weightage - 15%) The fabrication work will be done by using MS coiled pipes of 14 to 16 gauge as per requirement and in 1" to 2" of sections with anti rust coatings (SMAC RCCP - 120) in TWO layers, Colouring & Finishing: The entire art work, once installed, will be painted with combination of branded water based exterior emulsion and oil based auto colours and finishing touch. Including all labour, Material, all leads and lifts, with Transportation, including all necessary Scaffolding etc, complete. Commissioning (Work Weightage - 5%).

Chunyacha Ghana: Detailed Thematic Designing ,planning ,Providing and fixing, fabricating, erecting, and installing and handing over the scenic work replica of Chunyacha Ghana of 6 metre dia. The entire cladding work is divided in FOUR stages: Clay & Structure: (Work Weightage - 45%) The cladding will be created by using clay mould method, as referred in the approved drawings. Moulding & Production: (Work Weightage - 35%) Composite synthetic polymers and glass wool will be used in 3 layers for casting moulds and dyes for production with spray treatment of COT100. Fabrication, Installation and Colouring (Work Weightage - 15%) The fabrication work will be done by using MS coiled pipes of 14 to 16 gauge as per requirement and in 1" to 2" of sections with anti rust coatings (SMAC RCCP - 120) in TWO layers, Colouring & Finishing: The entire art work, once installed, will be painted with combination of branded water based exterior emulsion and oil based auto colours and finishing touch. Including all labour, Material, all leads and lifts, with Transportation, including all necessary Scaffolding etc, complete. Commissioning (Work Weightage - 5%).

Shubham EPC Private Limited