REPAIR / MAINT TO VARIOUS WASHING PLANT, SIGN BOARD, LIGHTNING PROTECTION AND VARIOUS SIZES OF GEYSERS, SOLAR WATER HEATERS, SOLAR LIGHT FITTING AND PETTY REPAIR IN ZONE C AND D UNDER AGE E/M AT GE JHANSI

Supply and fix single pointed copper rod 12 mm dia and 300mm long fixed on roof in and including all fittings, fixtures and PCC 1:2:4 type B-1 bolck 100mm x 100mm x 100mm complete all as specified and as directed

Supply and fix Galvanised Iron strip 32 x 6 mm burried in ground 150 mm below ground including all excavation and earth work connecting at ends, jointing etc complete all as specified and as directed.

M&L test point terminal bolck made of metal or phosphoras bronze of size 75 x75 x 25 mm of 6mm thick or copper strip of size 32 x 6mm, 100 mm long drilled and secrewd including 03 Nos 08mm dia 25mm hex head screw complete with box.

Supply and fix single pointed Aluminium rod 12 mm dia and 300mm long fixed on roof in and including all fittings, fixturres and PCC 1:2:4 type B-1 bolck 100mm x 100mm x 100mm complete all as specified and as directed

Supply and fix Aluminium strip 25 x3.15 mm with saddles and fixing screws etc for roof and down conductors above ground level complete all as specified and as directed.

Supply and fix Aluminium strip 32 x 6 mm burried in ground 150 mm below ground including all excavation and earth work connecting at ends, jointing etc complete all as specified and as directed.

M&L for earthing complete with copper earth plate electrode 600mm x 600mm x 3.15 mm thick buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level connecting to copper strip 20x3 mm as earthing lead by means of bolts, nuts, check nuts and washers of copper and earth wire protected by 50mm dia GI pipe medium grade and connected to pole structure/ panel board/earthing test point all as shown in electrical plate No. 3 of SSR Part-I(2009) and testing on completion complete all as specified and as directed. Note :- The unit rate quoted shall also include for excavation, earth work in any type of soil, plain cement concrete 1:3:6 mix, Type C1 pit, 40mm thick RCC 1:2:4 mix type B1 cover reinforced with 8mm dia TMT bras @ 150mm C/C both ways, GI funnel with watering pipe, wire mesh, protection pipe, earth strip up to 7.50m long complete in addition to item No. 1(a) to (e) of preamble (Notes) under sub heading earthing, specified in SSR Part II (b) Earthing result should be less than 3 Ohm required.

Material and labour for servicing of mechanical laundry with washing machine of whole system assembly including ,washer extractor(02 nos),drying tumbler(01 no),steam generator (01no) ,Air compressor,hydro extractor removing parts, applying blower to remove all dust, cleaning, washing, removing dirt, washing and cleaning of whole assembly system of the laundry the necessary parts and re-assembling the dismantled components, refixing to its original position and testing for proper functioning complete all as specified and as directed. Note -Defective compnents and parts will be repaired and replaced as per CA clause (under defect liability period )in which the system has been installed complete all as specified and as directed.

Supplying, installing, testing, and commissioning of Stored Pressure ABC Type Dry Chemical Powder Extinguisher of 6 kg capacity. Must conform to IS 15683 or equivalent international standards. Unit shall include a pressure gauge, discharge hose with nozzle, wall-mounting bracket, and initial charge of mono-ammonium phosphate-based powder. Installation includes grouting of MS flat brackets into the wall with necessary nuts and bolts complete all as specified and as directed

Supply, installation, testing, and commissioning of 25 kg capacity ABC-type (Dry Chemical Powder) fire extinguisher, trolley-mounted on a rugged MS wheel-based frame for easy maneuverability. The unit shall comprise a high-grade mild steel cylinder fabricated via MIG welding, conforming to IS 16018:2012. The extinguishing media shall be Mono Ammonium Phosphate (MAP 50% or 90%) powder as per IS 14609. The expulsion method shall be via an external 1 kg CO2 gas cylinder conforming to IS 7285. The assembly must include a minimum 3-meter long high-pressure discharge hose with a squeeze-grip nozzle, pressure gauge, and safety valve. The body shall be finished with anti-corrosive epoxy polyester powder coating in Signal Red (RAL 3000) complete all as specified and as directed