ADDITION ALTERATION TO BUILDING NUMBER P 355 IN ZONE A AREA AND REPLACEMENT OF OLD DETORIATED AND DEFECTIVE SLUICE VALVE AND CI PIPELINE WITH DI PIPELINE IN WATER SUPPLY INSTALLATION ZONE A AT GMS UNDER GE I GOS

Amount

M&L for Excavating in trenches in soft/ loose soil, not exceeding 1.5m wide and not exceeding 1.5 m in depth for foundation, n exc 10 sqm in plan and getting out complete all as specified and directed.

M&L for Excavating in trenches in soft/ loose soil, exceeding 1.5m wide and not exceeding 3.00 m in depth for foundation, n exc 10 sqm in plan and getting out complete all as specified and directed.

M&L for Cement concrete Type D-2, 1:4:8 (40 mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete (Design mix) M-30 (using 20 mm graded aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete (Design mix) M-30 (using 20 mm graded aggregates) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for Reinforced cement concrete (Design mix) M-30 (using 20 mm graded aggregates) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for Reinforced cement concrete (Design mix) M-30 (using 20 mm graded aggregates) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Reinforced cement concrete (Design mix) M-30 (using 20 mm graded aggregates) as in chajja and the like complete all as specified and directed.

M&L for Reinforced cement concrete (Design mix) M-30 (using 20 mm graded aggregates) as in Chullah hoods; stairways (except spiral staircases) including steps (square or spandril), string pieces, carriages, etc., complete, any section straight or winding, but excluding landings; RCC water tanks upto 1500 litres complete all as specified and directed.

M&L for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, Flat, with fair finished surfaces complete all as specified and directed.

M&L for Formwork to sides of pillars, posts, struts, piers, columns and stanchions (sqaure, rectangular or polygon) with fair finished surfaces complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. Flat, with fair finished surfaces complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) Flat, with fair finished surfaces complete all as specified and directed.

Formwork to staircases with sloping or stepped soffits including risers and stringers (excluding landing) with fair finished surfaces complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as speified and directed.

M&L for Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as speified and directed.

M&L for Returning, filing in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil etc complete all as specified and directed

M&L for Removing excavated material (Soil) exc. 250 m but n exc. 500 m and depositing where directed complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

M&L for Brick work with fly ash bricks straight or curved on plan exceeding 6 m mean radius complete built in cement mortar 1:6 complete all as specified and directed.

M&L for Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for Rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished even and smooth (without using extra cement) complete all as specified and directed.

M&L for applying 2mm thick Birla / JK Putty in two layers on newly plastered walls surfaces making absolutely even and smooth, rubbing with sand paper complete all as specified and directed

M&L Rendering 15 mm thick in cement mortar 1:4, in two layers (1st layer 10 mm thick rendering coat and 2nd layer 5 mm thick finishing coat) on brick work or concrete surfaces, second layer (finishing coat) mixed with liquid water proofing compound @ 200 ml / 50 Kg bag of cement as per manufacturer's instructions and finish the surfaces even and smooth without using extra cement complete all as specified and directed. Note : Liquid WPC will be measured and paid separately.

Supply only water proofing compound (liquid), ISI marked complete all as specified and directed.

M&L Rendering 5 mm thick in cement mortar 1:3 on concrete surfaces of ceiling and finishing the surfaces even and smooth complete all as specified and directed..

M&L for 10mm thick Light shade vitrified ceramic tiles in floors, not exceeding 0.36 sqm, set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

M&L for 10mm thick Light shade vitrified ceramic tiles in skirtings/ vertical surfaces, not exceeding 0.36 sqm, set & jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

M&L for 16 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

M&L for non skid ceramic coloured tiles of design as approved 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M&L for glazed ceramic coloured tiles 350 x 250 x 7 mm / 450 x 350 x 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M&L for Rendering 10 mm thick in cement mortar 1 : 4 for fixing of wall tiles complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring average 25 mm thick surface finished even and rough (as in levelling course) to receive the topping layer complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:6 for laying of floor tiles complete all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories. Net Opening will be measured for payment purpose) (Area not exceeding 2.00 sqm)

S&F 5 mm thick sheet glass ordinary quality and gazing with oil putty in square n exc 0.5 sqm in each pane complete all as specified and directed.

S&F 5 mm thick sheet glass ordinary quality and gazing with oil putty in square exc 0.5 sqm in each pane complete all as specified and directed.

S&F 12 mm thick plain Gypsum Board False Ceiling with GI frame including all necessary drilling cutting to fix electric items complete all as specified and directed with following:- (a) GI Grid channel 30x25x20 mm of 24 gauge fixed with rawl plug and screw 450 mm centre to centre alongwith perimeter walls. (b) GI channel made to shape 50x40x40 mm of 24 gauge placed @ 600 mm centre to centre from perimeter at wall except long wall (in one span). (c) GI intermediate runners of size 45x10x10 mm of 24 gauge fixed @ 1200 mm centre to centre leaving frame of one side walls (in other span). (d) GI sheet 25 mm wide and 20 mm gauge suspended fixed with steel fastner to roof ceiling and 1200 mm centre to centre including pluging of RCC Slab. (e) 12 mm thick gypsum board filling joints with POP and finishing complete with two coat of plastic emulsion paint over one coat of primer on ceiling.

M&L preparation of newly plastered surfaces and applying three coats of white wash but on ceiling complete all as specified and as directed.

M&L applying two coats of acrylic exterior weather proof emulsion paint over a coat of exterior primer on newly plastered wall surfaces complete all as specified and directed.

S&F Stainless steel fancy type curtain rod 25 mm dia as approved complete all as specified and directed

S&F SS Curtain rod Bracket fancy type for curtain rod 25 mm dia of any colour as approved complete all as specified and directed.

M&L 75 mm thick PCC 1:3:6 type C-1 using 20mm graded aggregate as in plinth protection finishing even & fair without using extra cement laid in bays with construction, 6mm thick joints should be filled with bitumen mastic filling comprising of one part of heated bitumen 80/100 gde and three part of sand ( all by weight) complete all as specified and directed.

M&L for hard core of gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as sub base of floor complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement. complete all as specified and directed.

S&F 7mm thick aluminium grills of make "Decogrill' model DG 104 surrounded by aluminium 'C' channel with mesh size 99 X 105mm complete all as specified and directed.

Demolition of Cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified & directed.

M&L for applying two coats of oil bound distemper on wall or concrete surfaces on prepared surfaces including, rubbing with sand paper complete all as specified and directed.

S&F White vitreous china wash down water closet pan pedestal pattern (white) excluding fixing bolts, flushing cistern and flush pipe complete all as specified and as directed.

S&F 10 Ltr capacity PVC valveless shyphonic action type low level flushing cistern white with inlet, ball valve, float valve and handle incl bracket and flush pipe of low level of 32mm dia fixed to wall complete all as specified and directed.

S&F Angle cock 15 mm bore fancy type chromium plated, with capstan head, high pressure, screwed down, screwed for iron pipe or for brass ferrule fixed to iron pipe complete all as specified and directed.

S&F Hand shower (Health faucet) with 1 mtr long Easy flex tube in crome finish & wall hook complete all as specified and directed.

Demolition of Reinforced Cement Concrete of any description and in any position not otherwise specifically provided for complete all as specified & directed.

M&L for pre cast cement concrete 1:1.5:3, type A-1, using 20mm graded stone aggregate as in cover slabs (for manholes etc) and similar articles with plain faces, set in CM 1:4 complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 1000 litre capacity hoisted and fixed in position complete all as specified and directed.

S&F Ball valves for 20 mm bore dia of pipe high pressure of PTMT with Epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (minimum weight 210 gms) complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S & F 15 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

S & F 20 mm bore 3 layer PP-R pipes SDR 7.4 & SDR 11 UV stablised and anti microbial welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded PP-R fittings complete to walls, ceilings or in floors complete all as specified and directed.

S&F in repair PP-R globe or gate valves screwed both ends for PPR Pipes of 20 mm bore dia of pipe complete all as specified and directed.

S&F in repair PP-R globe or gate valves screwed both ends for PPR Pipes of 25 mm bore dia of pipe complete all as specified and directed.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in Bricks/ stone Masonary wall complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints laid in floors, trenches complete all as specified and directed.

S&F PVC (SWR) pipes 75 mm bore Soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 110mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and directed.

S&F PVC(SWR) bends, any radius of 110 mm bore complete all as specified and directed.

S&F PVC(SWR) bends, any radius of 75 mm bore complete all as specified and directed.

S&F Stack clamps made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 110 mm PVC pipe complete all as specified and directed.

S&F Stack clamps made out of 50x5 mm flat iron, 16mm dia round iron stays including bolts & nuts and securing ends of stays to wall or roof for 75 mm PVC pipe complete all as specified and directed.

S&F Vitreous China urinals, half stall urinal, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement including waste pipe complete all as specified and directed.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

S&F Vitreous china WHB size 550x400 mm white flat back including PVC waste pipe but excluding taps, waste, chain & plug & porcelain stopper but including brackets with two coats of synthetic enamel painting over a coat of red oxide primer etc complete all as specified and directed.

S&F Vitreous china urinal partition white of size 310 x 700 mm complete all as specifeid and directed.

S&F PVC connection 15 mm bore, 450 mm long complete with both ends unions complete all as specified and directed.

S & F Brass CP Basin mixer 15mm bore for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F Stop valves fancy type, chromium plated 15 mm bore with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S & F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete all as specified and directed.

S&F 75mm PVC (SWR) floor trap, plain with grating,jointing with solvent cement as per site requrement all as specified and directed.

S & F 125 mm dia chromium plated shower rose of with or without swivel joint incl fixing to steel pipe complete all as specified and directed.

S & F in repair sheet Glass Shelf assembly consisting of 5.5 mm glass sheet shelf 12 cm wide with cromium plated bracket guard and railing 60 cm long complete all as specified and directed..

S&F LDPE pipe 50mm of pressure rating 6Kgf/sqcm fixed complete to walls, ceilings or in floors etc complete all as specified and directed.

M&L for Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 150 mm internal dia of pipe com plete all as specified and directed.

M&L for salt glazed stoneware (SGSW) drain pipes laid in trenches of 150 mm internal diameter of pipe and jointed in CM 1:1 complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L in repairs salt glazed stone ware gully traps size 150 x 150mm, square or round mouthed, type ‘P’ including setting and jointing to drains with CM 1:1 including demolition of existing traps complete all as specified and directed. (Note: CI grating will be meaured separately).

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, coping, benching, bed block, lintel band, plinth courses etc and similar work including weathering,slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

S&F mild steel framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings,frame work of watertanks and similar work conforming to Fe -290 Gde E-165 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm signle core PVC insulated unsheathed copper FRLSH multi stranded copper conductor cable in and including concealed PVC conduit of size 19 MM ISI marked inclusive of tees, bend, elbows etc upto and including GI sunk boxes of size 1.2 mm thick and 60mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switch/ socket of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sqmm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal incuding cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by ENgr-in-Charge for One light point controlled by one , one way switch 5 Amp.

All as per item no. 99 One fan point controflled by one, one way switch 5 Amps and regulator

All as per item no. 99 One exhaust fan point controlled by one, one way switch 5 Amps

All as per item no. 99 One 3 pin 5 Amps Switch socket outlet point controlled by one switch on the same board

All as per item no. 99 One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board

Description all as per tiem NO 99 here in before but using 2.5 Sqmm single core copper conductor cable of multistranded flame retardent PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket combition point including necessary running of 2.5 Sqmm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly.

M&L for Modular switch 1 way 6A, 1 module complete all as specified and directed

M&L for Ceiling rose 3 terminals of PVC/ polycarbonate, as per relevant IS code, ISI marked isolated body complete all as specified and directed.

M&L Modular Socket outlet 2 in 1, 6 pin 6 Amp 2 module ISI marked, complete all as specified and directed.

M&L for Modular switch 1 way 16A, 2 Module 3 pin ISI marked, complete all as specified and directed

M&L for Socket 6A/16A - 2/3 pin combined 2 module, ISI marked, complete all as specified and directed

M&L for Fan step regulator, 120W - 1 module, ISI marked complete all as specified and directed

Supply and fixing lights fitting 1x 20W, 220V, surface and wall mounted LED batten with polycarbonate housing and integrated electronic driver including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed

S&F decorative mirror light fitting of capacity 7 W 220 volts , 50 Hz complete all as specified and directed. Make: Philips Cat Part No 31402 or equivalent

M&L for Sheet metal enclosure factory made double door for mounting MCBs with 200A rated bus bar Scapacity SPN 8 way AC 240 Volts with IP-43 protection, complete all as specified and directed.

Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of capacity 40 to 63 Amp SPN 240 Volts and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

M/L of 2 Runs of cable PVC insulated but unsheathed 1.5 Sq mm, stranded copper conductor in and including PVC conduit with continuous earthing cable PVC insulated 1.5 Sq mm, stranded copper conductor all as specified and directed.(Cable make Anchor/Havells/Finolex) Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre.

Submain wiring with two single core 4.0 Sqmm size stranded copper conductor PVC insulated unsheathedcable FRLS in and incl PVC rigid non metalic conduit concealed/ surface type and one PVC cable of 4.00 Sqmm size solid copper conductor PVC insulated andunsheathed for continous earth wire with junction boxes covered with laminated sheet 3 mm thick and other accessories complete all as specified and directed.

M/L for 2 Runs of cable PVC insulated but unsheathed 6.0 Sq mm, stranded copper conductor FRLS in and including PVC conduit with continuous earthing cable PVC insulated 6.0 Sq mm, stranded copper conductor FRLS all as specified and directed.(Cable make Anchor/Havells/Finolex) Note :-2 runs of cable, one run of earth wire (copper cable) & one run of PVC conduit shall be measured as one running metre.

Supply and fix exhaust fan made of sturdy Engineering plastic complete voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 260 mm suitable for ceiling fitting including the exhaust pipe of suitable size complete. Make Usha Crisp Air Premia or equivalent

S&F crysta chip on board (COB) swivel downlight with crisp light throw and high CRI with capacity 3Watts complete 220 volts all as specified and directed. Make Havells cat Part No LHEEGEPBIE1W003. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

S&F aesthetically designed, decorative recess mounted 12 Watts (Round) 6500K spot light for low ceiling height complete all as specified and directed. Make Havells Cat Part No LHEEBPP7IL1W012. Note : Contractor will write in permt maker CA No and date of instllation on the light fitting

Supply and fixing of new generation energy saving and environmental friendly long life LED bldg security lights with capacity 25 watts made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover having botom opening separate driver compartment with IP66 protection and impact resistance of IK08 complete all as specified and directed

Material labour for laying of concealed PVC conduit of size 20/25 MM ISI marked inclusive of tees, bend, elbows for one telephone socket point alongwith for RJ-11 telephone socket with transparent shutter 1 module alongwith fulsh metal box 1 module and front cover plate 1 module complete all as specified and directed.

Material labour for laying of concealed PVC conduit of size 20/25 MM ISI marked inclusive of tees, bend, elbows for one TV socket point alongwith TV socket 1 module alongwith fulsh metal box 1 module and front cover plate 1 module complete all as specified and directed.

S&F flexible led strip light to be fixed in ceiling 220 volts , 50 Hz with driver complete all as specified and directed

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and ccessories, 230 V, 1400 mm sweep. Min air delivery 245 CFM with service value 6.00 BEE. Five star rated complete all as specified and directed

Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less'than 1.5 meters below normal ground level, connected to galvanised iron earth lead wire of 4 mm dia GI pipe mediam grade 15 mm dia upto 7.5 mtr including provn of conrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick cover of RCC (1:2:4) reinforced with XPM (weight not less than 4 kg/sqm) and frame of angle iron 25x25x3 mm with lugs 02 Nos and with 6.0 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for earth plate, common sald and charcoal filing, test point made out of Bronze/ Gun metal with fixing arrangement, funnel, wire mess and excavation/ earthwork in hard/ dense soil, to a distance not exceeding 50 mtr all as per electrical plate No 3 of SSR 2010 Part I and connecting to earth test point all as specified or indicated incl testing on completion.

S&F for modular MCB 5 to 32 SP 240 volts 50 Hz complete al as specified and directed

M&L for street light fitting bracket made out of 25 mm bore GI pipe, light grade, tubing bend to shape, 1.2 metre long, fixed to pole/wall, painting with two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.

M&L for automatic hand dryer ABS plastic automatic sensor high jet speed with power 1800 watts, 240 volts, 50 Hz, with induction distance 5 to 20 mm complete all as specified and directed

Supply and laying for 3- layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply all PP-R plain & brass threaded polypropylene random fittings of outer dia 25 MM laid in trenches. complete all as specified and directed

S&F PP-R Gate valves (brass insert) as per requirement of the site of size 25 mm complete all as specified and directed

Making connection of PP-R distribution branch with PP-R main of 16-40 MM sizes by providing and fixing tee including cutting and making fusion joint etc

M&L for XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 16 sq. mm 2 Core complete all as specified and directed

Supply and providing sand cushioning with dry clean sand 15 cm below cable and 8 cm above the cable complete all as specified and directed. Note : Punned thickness shall be measured for the purpose of payments.

Supply and laying flyash building bricks laid in trenches for LT cable complete all as specified and directed.

M&L for Tubes, 'light grade', galvanised, with all fitting; laid in trenches, walls of bore 25 mm for laying of cable complete all as specified and directed

M & L for Taking up or down CI/GI/PPR of water mains of 150mm bore(including all fittings), with spigot and socket ends and lead joints including burning out joints incliding turning water OFF or ON as necessary and taking off and refixing covers, access doors etc. complete all as specified and directed.

All as per item No 138 above but 100 mm bore dia

Supply , laying, jointing & testing of 150 mm dia DI Type K-7 pipe with socket & spigot ends, with cement morter zinc coated out side as per IS 8329/2000 in standard length suitable for and including push on tyton joints with rubber rings, laid in trenches complete all as specified and directed by Engr in charge. Note: (Excavation and earth work, DI specials will be measured and paid seperately)

Supply , laying, jointing & testing of 100 mm dia DI Type K-7 pipe with socket & spigot ends, with cement morter zinc coated out side as per IS 8329/2000 in standard length suitable for and including push on tyton joints with rubber rings, laid in trenches complete all as specified and directed by Engr in charge. Note: (Excavation and earth work, DI specials will be measured and paid seperately)

M& L for MS/CI/DI fittings up to 150mm bore such as collar, bends (any type radius, any angle, double end socketted or double flanged or spigot & socket, tail pieces (all socketed or all flanged with an equal & other end tapering bellmouth or flanged plates, connecting pieces straight (both end flanged or socketed of socket & flanged & spigot ends or bellmouth tailpieces ( one end flanged & other end spigot or socket or tapering as bell mouth or flanged ) caps blank flanges heavy duty suitable for mechanical joint/flanged joint with and incl taking down old fitting of any type and any size complete all as specified and directed. Note: Certifiacte for Weight of fitting by the manufacturere shall be submitted before payment.

Supply and fixing and testing resilient sealed sluice valves 200mm bore of dia both ends flanged and drill in with brass spindle and brass check nuts, hand wheel made out of CI complete suitable for tested hydrostatic pressure 15 Kg/Sqcm. (PN 1.6) and confirming to IS 780 complete and of size 100mm dia Make: Kirloskar/Zoloto/BIR

All as per Item No 143 but of size 150mm dia

All as per Item No 143 but of size 100mm dia

All as per Item No 143 but of size 80mm dia

Taking down old unserviceable and Supply and fixing Monoblock pump sets , electric driven ,Three phase suitable for suction and delavery line size 100x80 mm , 30 HP (22KW ), Head 48 meter and discharge 28 litres per second. (Model KDS 3068+ ,code D12013000110, Make :KDS,kirloskar complete fitting and testing ,alignment of motor , all as specified and directed NOTE: The Unsv. Pump sets will be Deposited to the AGE E/M Store yard .

Taking down old unserviceable and Supply and fixing Monoblock pump sets , electric driven ,Three phase suitable for suction and delavery line size 100x80 mm, 25 HP (19KW ),Head 44 meter and discharge 26 litres per second (Model KDS 2560 ,code D112012500110, Make :KDS,kirloskar complete fitting and testing ,alignment of motor , all as specified and directed NOTE: The Unsv. Pump sets will be Deposited to the AGE E/M Store yard .

M&L cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as concreting filling and mass concrete complete all as specified and directed

M/S. KISHAN ENGINEERING

DHABALESWAR ENGINEERING WORKS

M/S JAGANNATH SASMAL

M/s MAA BHAIRABI ENTERPRISES

HARAGOURI SUPPLIERS

M/S SIWALIK AND CO

G.KRISHNA MURTHY AND PARTNERS

M/s Ats Electricals