Wear Plate for Yoke Pin Support .

Special Eligibility Criteria

1. 1

   i. In terms of para 2.1 of Instructions to Tenderers Rev 1.21 April 2024 (along with all correction slips), Railway reserves the right to order either the entire or Bulk or entire purchase from UVAM sources of RDSO Item ID Item :3100432,Silico- Manganese & Manganese Steel Liners & Wear Plates for Bogie and Couplers Or their authorized dealer. Status of approval of tenderer shall be reckoned as on the date of tender opening and not thereafter, unless it is a case of downgrading/ removal/ suspension/ banning. ii. (a) Vendors approved for developmental ordering shall be eligible for developmental order of up to 20% of Net Procurable Quantity [NPQ] in regular tenders. ii. (b) Vendors approved by any centralized vendor approving agencies for developmental orders with condition of prototype approval and/or field trial, may be given developmental order for 5% of Net Procurable Quantity [NPQ] within or outside NPQ. However the total order on developmental firms will be limited to 20% of the NPQ. iii Authorized dealers/ distributors need to quote with Tender specific authorization from the approved vendors/developmental vendors/Manufacturers failing which offer will be summarily rejected. While issuing such authorizations the approved vendors/developmental vendors/Manufacturers must ensure that these authorized dealers/distributors are in a position to raise inspection requests on IREPS.

   Document optional
2. 2

   In keeping with the Public Procurement (Preference to Make in India) Order, 2017, as amended, and in terms of clause 2.4.2, 2.4.5 and 2.4.6 of Instructions to Tenderers Rev. 1.21 April 2024 and Railway Board Circular No.2015/RS(G)/779/5(Vol. III) Dated :12.07.2020, Public procurement of this item is restricted to Class - I local suppliers only. Thus, only class-I local supplier as defined under the public procurement (preference to Make in India) Order, 2017, as amended shall be eligible to bid in this tender. Offer from vendors who do not quality to be Class - I (Local Content :minimum 50% ) local supplier, shall be summarily rejected and, therefore, such vendors should not participate in the tender. In case any vendor who does not qualify to be a Class - I local supplier for the tendered item participates in the tender, such a bidder does so at its own risk and cost and Railways shall not be liable for any loss or damage caused to the bidder on this account. NOTE -: As per Public Procurement (Preference to Make in India) Order, 2017, procurements where the estimated value to be procured is less than Rs 5 lakhs shall be exempt from this Order.

Commercial-Compliance

1. 1

   In terms of clause as per Para 2.4.3 of Instructions to Tenderers for Electronic tenders Rev 1.21 April 2 0 2 4 regarding Restrictions on procurement from a bidders of a country which shares a land border with India, I, hereby confirm that I have read the clause regarding restrictions on procurement from a bidder of a country which shares a land border with India and I certify that I am not from such a country.

   Document optionalConfirmation required
2. 2

   No Exemption for EMD will be given to firms except to those firms as mentioned in the Instruction to Tenderers Revision 1.21 April 2024 (along with all correction slips). If the firms, other than those exempted, fail to submit EMD along with the offer, their offer will be summarily rejected.
3. 3

   For Security Money deposit, Special attention is drawn to Para 12.0 of Electronic Tender Revision 1.21 of April 2024 along with Correction Slip No. 01 of ITT_1.21_April_2024 dated 19.09.2024 and for Liquidated Damages Special attention is drawn to Para 15.0 of Electronic Tender Revision 1.21 of April 2024.
4. 4

   Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.

   Document optional

General Instructions

1. 1

   Bank Account details for the purpose of payment shall be taken as appearing in the profile of the vendor in IREPS. In case, there is any change in the bank account details, vendors are advised to update their bank account details in their IREPS profile before submitting their e-bids.
2. 2

   MARKING : Vendor name/identification marks as well as month and year of manufacture must be inscribed/engraved/screen- printed/embossed on item supplied to Northern Railway as per the relevant drawing/specification/description.

1. 1

   Validity of Offer: No deviation from the offer validity period stipulated in the tender is permitted.

2. 2

   MODE OF DESPATCH : By Road Transport on freight pre-paid and door delivery basis.

3. 3

   FOR : Destination