Modernisation of the Pilavukkal Periyar Dam Park, Renovation of its Infrastructures and Improvements to Approach road in Pilavukkal Periyar Dam at Khansapuram village of Watrap Taluk in Virudhunagar District.

Clearing the Scrub jungle and disposing of the same etc., complete complying with standard specification and as directed by the Departmental Officers.

Thorough scrapping of old plastered surface including all cost etc., complete complying with standard specification. W-0106

Dismantling,clearing away Stone/ Brick Masonry and carefully stacking materials usefull and re-use for 3m hight removal of debris, unloading, conveyance charges for 1kmclearing and levelling the site, etc., complete complying with standard specification.

Dismantling RCC by manual / by using deploying machineries etc, complete complying with standard specification and as directed by the Engineer in charge of work.

Earth work excavating and depositing on bank with initial lead of 10 m & initial lift of 2m in Hard stiff clay, stiff black cotton, hard red earth, shales, murram, gravel, stoney earth and earth mixed with small size boulders SS.20B

Trimming the bed and the side slope of the bank in all soils except hard rock upto a thickness of 7.5cm to 15cm and making it ready to receive the concrete

Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Providing and placing in position of Plain Cement Concrete of grade M 10 using hard well graded coarse aggregate of maximum nominal size of 40mm weigh batching the ingredients and mixing in approved mixers/ batching plant (to produce concrete of the specified characteristic strength of 10N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work (Without Vibration).

Supply and filling in foundation and basement with Gravel in layers of not more than 15cm.thick well rammed watered and compacted with surface vibrator, watered and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and filling in foundation, basement, etc with filling Stone Dust in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and erecting steel centering for Column Footing, pedestal, plinth beam sides and soffits including supports and strutting up to height of 3.29 m for plain surface with all cross bracings using mild steel B.G.10 gauge sheets of size 90cm x 60cm stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over silver oak (country wood) joists of size 10cm x6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre complete complying with standard specification and as directed by the by the Engineer in charge of work (The retrieved materials should be taken back by the contractor ). The payment for centering should be made after the concrete is laid etc.,

Supplying and erecting water tight steel centering for sides and soffits including supports and strutting up to height of 3.29 m for plain surfaces such as RCC slab, Vertical Slab, Side slabs of RCC works with all cross bracings using mild steel B.G.10 gauge sheets of size 90cm x 60cm stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding laid over silver oak (country wood) joists of size 10cm x6.5cm spaced at about 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 75cm centre to centre complete complying with standard specification and as directed by the by the Engineer in charge of work (The retrieved materials should be taken back by the contractor ). The payment for centering should be made after the concrete is laid etc.,

Without Strutting

With Strutting

Providing and placing in position of Plain Cement Concrete of grade M 15 using hard well graded coarse aggregate of maximum nominal size of 20mm weigh batching the ingredients and mixing in approved mixers/ batching plant (to produce concrete of the specified characteristic strength of 20N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work. (With Vibration)

Providing and placing in position of plain Cement concrete of grade M15 using hard well graded aggregates with the nominal maximum size of coarse aggregate of 40mm (60%) and 20mm (40%); weigh batching the ingredients and mixing in approved mixers/batching plant (to produce concrete of the specified characteristic strength of 15 N/mm2 at 28days) including dewatering the placement site by bailing/pumping and by diverting wherever necessary; laying the concrete in layers of not exceeding 15 cm thick and in bays; vibrating, compacting and finishing the surface with all leads and lifts; watering curing complete so as to attain the profile and strength specified in the approved drawing & specifications etc., complete complying with standard specification and as directed by the Departmental Officers (with vibration).

Providing and placing in position of Plain Cement Concrete of grade M 20 using hard well graded coarse aggregate of maximum nominal size of 20mm weigh batching the ingredients and mixing in approved mixers/ batching plant (to produce concrete of the specified characteristic strength of 20N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work. (without vibration)

Providing and placing in position of Reinforced Cement Concrete M20 grade using hard well graded coarse aggregate of maximum nominal size of 20mm weigh batching the ingredients and mixing in approved mixers/ batching plant (to produce concrete of the specified characteristic strength of 20N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work. (with vibration)

Below G.L

Providing and placing in position of Reinforced Cement Concrete M25 grade using hard well graded coarse aggregate of maximum nominal size of 20mm weigh batching the ingredients and mixing in approved mixers/ batching plant (to produce concrete of the specified characteristic strength of 25N/Sqmm in 28 days) including dewatering the placement site by bailing / pumping and diverting wherever necessary, laying the concrete in layers of not exceeding 15cm thick and in bays, compacting and finishing the surface to the profile with all leads and lifts, watering, curing to attain the strength as specified in the drawing for various depth and height below and above ground level etc., complete complying with standard specification and as directed by the Engineer in charge of work. (with vibration)

Supplying fabricating and placing in position of Ribbed tor steel bars of various diameter for all Reinforced Cement Concrete works including cost of rods, binding wire, Labour Charge for cutting the rods to the required length, bending, tying and fixing in position complete for various height below and above ground level etc., Complete complying with standard specification and as directed by the by the Engineer in charge of work.

Brick work in following Cement Mortar 1:5 using best quality Burnt Clay Brick of size 9” x 4 1/2” x 3” with class designation of 10 conforming to IS 1077-1992 for oundation and basement including Cost of Mortar Plasticizer curing, etc.,complete mplying with standard specification and as directed by the departmental officers. ickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge.

Basement Floor

For Ground floor

For First floor

Brick partition walls of 11.50cm thickness using best quality Burnt Clay Brick of size 9” x 4 1/2” x 3” with class designation of 10 conforming to IS 1077-1992 in Cement Mortar 1:3 (One Cement and Three CS Sand) using hoop iron reinforcement if found necessary including Cost of Mortar Plasticizer, curing etc. complete complying with standard specification and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering Sand) 10mm thick including mortar plasticizer at 200ml per 50Kg of cement used , hacking the surfaces and curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering the surface of walls with Cement Mortar 1:3 (One cement and Three plastering sand), 20mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used , curing etc., complete complying with standard specification and as directed by the departmental officers.

Plastering the surface of walls with Cement Mortar 1:5 (One cement and Four plastering sand), 12mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used, curing etc., complete complying with standard specification and as directed by the departmental officers.

Internal Plastering

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 20mm thick in all floors including mortar plasticizer at 200ml per 50Kg of cement used curing etc. complete complying with standard specification and as directed by the departmental officers.

Stucco plastering 12mm thick using blue granite chips of size 10mm and below over a base plastering with cement mortar 1:5, 12mm thick, etc., complete complying with standard specifications

White washing two coats with freshly burnt white shell lime in all floors including cost of lime, blue powder fevicol type gum, brushes, scaffolding charges, etc., complete complying with standard specification and as directed.

Colour washing two coats in all floors using best freshly burnt white shell lime and best quality of approved variety of colouring pigment including cost of lime, colouring pigments, fevicol type gum, brushes, scaffolding charges etc., complete complying with standard specification. Mineral colouring pigments not affected by lime should only be used (stainers and colour solutions should not be used.)

Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting the wall two coats with approved weather proof Exterior Emulsion paint over one primer coat on cement Plastered wall surface ect., complete complying with standard specification and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting Old iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with Two coats of best approved first quality and colour of synthetic enamel paint in all floors etc., complete complying with standard specification and as directed by the departmental officers.(The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Painting Old Plastered Wall Surface with Two finishing coats of ready mixed (Emulsion) of approved quality and colour over the existing wall in all floors etc., complete complying with standard specification and as directed by the departmental officers. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and painting the walls with two coats of wall putty as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications and as directed by the departmental officers. (The wall putty shall be got approved by the Executive Engineer before use of work).

Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothly with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (water proof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers.( The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (water proof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coats of putty, scrapping the putty area to level the surface smooth, etc.,complete. The putty should be got approved by the Executive Engineer before use on work

Supplying and fixing Mild Steel grills for windows, ventilators etc.,complete complying with standard specifications and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Granite Stone Slabs of following size and Variety with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., complete complying with standard speicification and as directed by the departmental officers.(The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work)

Paving the floor with best quality vitrified Tiles of 600x600x8mm and variety conforming IS 15622 with water absorbtion less than 0.08% of approved colour and shade laid over cement mortar bed of 20mm thick in cement mortar 1:3 (one cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer in all floors and the top pointed with Water Resistant Tile Epoxy Grout etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in accordance with IS 1443 over a cement mortar bed of 20mm thick in Cement Mortar 1:3 (One Cement and Three crushed stone sand) with required Cement Slurry and Mortar Plasticizer and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with following best approved quality, white glazed tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)Dadooing walls with following best approved quality, white / colour glazed tiles conforming to IS 15622 of following sizes in Cement Mortar 1:2 (One Cement and Two crushed stone sand),10 thick with Mortar Plasticizer and pointing the joints with Water Resistant Tile Epoxy Grout at the rate of 0.27 Kg. / sq.m. neatly in all floors, curing, etc., complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by Executive Engineer before use on works)-(first quality white glazed tiles of size150mm x 150mm x 6mm )

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone M.Sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of 230mm x 230mm x 20 mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Supplying and fixing of marble of 0.61*1.22m.,18/20mm thick in all floors for urinal partition including for labour charges for fixing and polishing etc.,

Fabricating, Supplying and fixing in position of steel sheeted windows with the following specifications. Outer frames of windows made of ‘Z’ section F7D of size 33 x 25 x 3mm at 1.419 kg/ m and mullion ‘J’ section (F4B) of size 46x25x3mm at 2.28kg/m and shutter section of made of F7D of 33x25x3mm at 1.419 kg/m as specified in IS 7452/1990. Each openable shutter should not exceed a width of 600mmto enable separate operations and easy maintenance. The panel of the shutters to be covered with 18 gauge cold rolled sheet of superior quality and welded intact with shutter frames. Horizontal stiffeners using 18x5mm MS Flat at 0.70kg/m at 3 Nos. for each shutter and additional diagonal stiffeners of the same MS flats at all the four corners of each shutters to the suitable length welded to the shutters, for holding the CR Sheets in position firmly. 2 numbers of Steel Offset Pivot hinges of size 3” and one number of handle-Cu.m-latch of special type made with 18x5mm MS flats are revetted to the shutters at an appropriate height in window. suitable opening is left for its easy operation. a stopper square rod for handle is provided in the mullion section at suitable place to catch the window handle. each window shutter having an adjustable stay made out of 18 x 5mm at 0.70 kg/ m MS flat of length 320mm with three adjustable position. A matching peg is provided in the outer frame of the window at suitable place. 4 Nos. of hold fasts of 200mm length spliced at the ends are welded to the outer frame of the window by using MS flat of 18x5mm at 0.70kg/m, welded to the shutter at two place equivalent from each from top and bottom of the shutter. An MS square bar of 12mm size is welded to theinner face of the window at an equal interval not exceeding 100mm edge between them. All members are painted with one coat of anti-corrosive red oxide primer as directed by the departmental officers. All sections should be in confirmed with IS 7452/1990.The cost includes cost of all materials, labour charges and other incidental charges, etc., complete complying with standard specification and as directed by the departmental officers.

Manufacturing supplying and fixing of Fully Panelled steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames, stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter. 3nos. of Steel Parliament Hinges of Size 125mm x 150mm in case of single leaf and 6nos. of Steel Parliament Hinges of Size 125mm x 150mm in double leaves shutter to be provided. 6nos. of holdfasts 200 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 3 nos, one at the top, one at lock rail(Inner) and the other at the bottom are provided 1no. Aldrop is provided at lock rail section in the door 2 Nos of 200mm handle are to be provided. One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters. at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete complying with standard specification and as directed by the departmental officers. -Single leaf of size 1.00m x 2.10m.

Supplying and Fixing in position steel glazed Ventilators with central hung swing shutter using F7D section of size 30x25x3mm for inner outer froames with 4 Nos. Of 12mm dia MS sq.bars for protection and 2 Numbers of clamps welded with outer frame and using 3mm thick pin headed glass for panel including painting with one coat of Red Oxide Primer dismantling the masonry wherever necessary for fixing the ventilator and redoing the same to the original condition fixing the ventilator and redoing the same to the original condition fixing the ventilator in position etc. complete complying with standard specification and as directed by the departmental officers.

Supplying and Erecting Pull and Push Type Rolling Shutter with ISI make of approved size and section using 18 GI sheet. The shutter shall be painted with one coat of red oxide primer and the rate is inclusive of hood covers, transportation charges etc (manually operated) (upto 8 Sq.m Area)

FRP Door Sutter with FRP Door Frames made out of FRP Sheets of 3mm thick of over all size 65mm x 50mm with rebate suitably reinforced using MS Angle / Flats, cost of holdfasts and Solid Core FRP Shutter Panel of 5mm thick and hollow core frames of 3m wall thickness for styles and rails etc., of sizes specified by Engineers M-0394

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of neceSORy PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cast of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of “U” clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification and as directed by the departmental officers

110mm dia

160mm dia

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

110mm dia pipe

75mm dia pipe

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications (for both internal and external water supply arrangements). The valves to be used on work shall be got approved by the Executive Engineer before use on work.

25mm Gun Metal Gate Valve

32mm Gun Metal Gate Valve

40mm Gun Metal Gate Valve

Supplying and fixing in position 15mm dia brass CP screw down tap / Pillar tap (heavy duty) of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

SD Tap

Pillar Tap

Supplying, laying and jointing UPVC pipes of Class 6 (having working pressure of 12.50 kg/sq.cm) conforming to IS 4985- 2000 of approved quality and best variety of the following dia including cutting and fixing UPVC specials using UPVC adhesives (but excluding cost of such specials) in accordance with IS 7634-3 (2003) and fixing into wall with teak wood plugs, PVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works.

a)Internal water supply above ground level

25mm dia Pipe

32mm dia Pipe

b)External water supply above ground level

32mm dia Pipe

Supplying UPVC Specials (with working pressure 10 kg. / sq.cm.) in water supply arrangements (both in internal and external water supply arrangements Since the labour for cutting, threading / pasting, sundries have already been included under pipe line item of works, no separate provision for fixing UPVC specials needs to be allowed

Coupler

25mm dia Pipe

32mm dia Pipe

Elbow

25mm dia Pipe

32mm dia Pipe

25mm dia Pipe

32mm dia Pipe

25mm dia Pipe

32mm dia Pipe

Union

25mm dia Pipe

32mm dia Pipe

Reducer

25 mm x 20 mm

32 mm x 25 mm

Reducer Tee

25 mm x 20 mm

32 mm x 25 mm

Reducer Elbow

25 mm x 20 mm

32 mm x 25 mm

Hex Nipple

25mm dia Pipe

32mm dia Pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).(D)

PVC Elbow

160mm dia

110mm dia

75mm dia

PVC Elbow with Door

160mm dia

110mm dia

75mm dia

PVC Tee

160mm dia

110mm dia

75mm dia

Supplying and fixing in position best quality and approved make Indian made white / colour glazed earthernware wash hand basin of size 550 x 400mm (with pedestal / without pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia “B” class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).- (White color without pedestal)

Supplying and fixing in position Indian make bevelled edge mirror of approved quality and brand PVC / Fibre Glass framed 5.5mm thick mirror of followingsize , Shelf type with hard board backing of approved colour fixed with brass screws, rawl plug, etc., complete complying with standard specification. (The mirror should be got approved by the Executive Engineer before use on woks)- Size 600 x 450 mm

Supplying and fixing best approved best quality Procelain CP soap tray of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The soap tray should be got approved by Executive Engineer before use on works).

Supply and fixing in position of best Indian make white / colour glazed earthernware lipped mouth flat back urinal of best quality and approved make of size 430mm x 260mm x 350mm with GI pipe, 32mm dia bell mouth PVC connection and waste pipe, 15mm dia GI pipe of required length, 15mm dia GM wheel valve, 15mm dia brass nipple 2 Nos., and fixing the urinals in position with necessary TW plugs, clamps, screws, etc., including dismantling masnory and re-doing the same to the original condition, etc., including painting the pipe with two coats of best quality approved synthetic enamel paint over one coat of red oxide primer and checked without any leakage etc. complete complying with standard specifications and as directed by the departmental officers. (The urinal should be got approved by the Executive Engineer before use on works.) - White Glazed Urinal

Supplying and fixing in position white / colour glazed European Water Closet of best quality and approved make with 100 mm “P” or “S” trap connecting with CI pipe of 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn,teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings such as 15mm brass ball valve with polythene float with brass handle, union, coupling connected by means of 40mm white PVC flush hand using Indian adopter joint including all internal fittings such as 15mm brass connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe including cost of 600mm length of 110mm dia PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition etc. complete complying with standard specifications. (The EWC and flushing tank wiht all accessories should be got approved by the Executive Enginer before use on works)-white in colour

Supplying and fixing of Granite Sink of size 600 x 600 x 250mm (M-0556)

Supplying and fixing in position CP Two Way Bib Cock with Health Faucet complete complying with standard spoecifications,labor inclusive of fixing lowlevel flushing tank.

Supply and fixing of 300mm (12") sweep (heavy duty) AC exhaust fan complete with necessary wall opening and making good of the wall

Supplying and fixing position CI Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of crushed stone sandand five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position 150 x 100mm "P" or "S" stoneware gully trap 'A' grade with CI double gratings of size 150 x 150mm and 230 x 230mm at bottom and top respectively with necessary earth work excavation laid over a bed of brick jelly cement concrete 1:3:6 (One cement, Three crushed stone M.Sandand Six broken brick jelly) 150mm thick using 40mm size broken brick jelly including necessary brick work and plastering including dismantling masonry wherever necessary and re-doing the damaged portions to the original conditions using cement concrete 1:3:6 using 20mm stone jelly for fixing the gully trap and giving connections to stoneware sewer line etc., complete complying with standard specifications. [Earth work excavation, brick work, plastering shall be measured and paid separately]. The stoneware gully trap should be got approved by the Executive Engineer before use on works.

Supplying and Fixing of Tamil Brass Letters and Tamil Stainless Steel Letters of approved size and colour. The colour treatment process is achieved with colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes

Tamil Brass Letter 25cm

Tamil Brass Letters 20cm

Tamil Stainless Steel Letters- Emblem (15)

Earthwork Excavation THE RATES FOR EARTH WORK EXCAVATION AND REFILLING FOR PIPE LINE WORKS HAVING BED WIDTH OF 1.25M AND BELOW ON LINEAR MEASUREMENT BASIS

110mm Dia HDPE Pipe

160mm Dia HDPE Pipe

Refilling THE RATES FOR EARTH WORK EXCAVATION AND REFILLING FOR PIPE LINE WORKS HAVING BED WIDTH OF 1.25M AND BELOW ON LINEAR MEASUREMENT BASIS

110mm Dia HDPE Pipe

160mm Dia HDPE Pipe

Supply and Delivery of HDPE PIPES PN10- PE 100 AS PER IS 4984/2016 (Pre-Compounded Resin) including all cost and conveyence etc, Complete asper standard specification.

110mm Dia HDPE Pipe

160mm Dia HDPE Pipe

Lowering HDPE pipes and specials to trench and laying to proper grade and alignment and as directed by the TWAD Officers

90mm to 110mm Dia (OD) HDPE Pipe

125 to 160mm Dia (OD) HDPE Pipe

Jointing HDPE Pipes and Specials by butt fusion welding / electro fusion welding joints using fusion equipment as per ISO 21307-2011 and as per IS 7634 (part-2) : 2012 including cost of hire charges for butt fusion equipment power supply arrangements etc., complete as per directed by TWAD Board Officers

110mm Dia HDPE Pipe

160mm Dia HDPE Pipe

SPECIALS FOR HDPE PIPES AS PER IS 8360/1977/Part I(Reaffirmed 1992) Part II and III (Reaffirmed 2002) including all cost and conveyence etc, Complete asper standard specification.

90 Degree Bend

110mm Dia

160mm Dia

Equal Tee

110mm Dia

160mm Dia

Supply and Delivery of DUCTILE IRON SOCKET/SPIGOT PIPES AS PER IS 8329/2000 FOR CLASS K7 including all cost and conveyence etc, Complete asper standard specification.

D.I Pipe150mm dia

D.I Pipe100mm dia

Supply and Delivery of DUCTILE IRON CLASS PN10 FLANGED PIPES AS PER IS 8329/2000 including all cost and conveyence etc, Complete asper standard specification.

1 m length of pipes 100mm

2 m length of pipes 100mm

2.5 m length of pipes 100mm

Supply and delivery of DI D/F Gate (sluice) valves (soft seated) resilient seated soft sealing Gate Valves (Sluice Valves) with body Bonnet of Ductile cast iron of Grade GGG 40 or GGG 50, Wedge fully rubber lined with EPDM replaceable spindle nut without gland packing and with 3 O- Ring protection on the shaft and seals of NBR and the valves should be of Vacuum tight and 100% leak proof with face to face dimensions as per BS 5163-89/ISI 14846-2000/DIN 3202 F4. All the valves should be with electrostatic powder coating both inside and outside with pocket less straight through body passage. All the valves are to be compatible for buried application with pressure rating PN 10/16 and with 5 years warranty

100mm Dia

150mm Dia

Manufacture, Supply and Delivery of Tamper proof DI single chamber double orifice triple function (ventilating, admitting & ventilating during operation) air release valve with pressure rating PN 10/16 with body and cover made of Ductile Iron of Grade GGG 40 or GGG 50, conforming to IS 1865 with Food Grade Epoxy Powder coating (EP-P) inside and for outside of colour blue RAL 5005. All internal parts such as float, shell etc., cover bolts, made of Austenitic alloy steel of SS AISI 304/316. The float shall be made of Polytetrafluroethylene/ Austenitic alloy steel of AISI 304/316. Gaskets and seals of EPDM / Neoprene rubber for TWAD Board works anywhere in Tamil Nadu and with 5 years warranty

100mm Dia

150mm Dia

Lowering of D.I Pipes and specials in the trenches and laying to proper grade and alignment and as directed by the TWAD Officers.

D.I Pipe150mm dia

D.I Pipe100mm dia

Jointing the C.I/ D.I - S/S pipes and specials with molten lead and Yarn including caulking the joints. (Including cost of jointing materials).

D.I Pipe150mm dia

D.I Pipe100mm dia

Supply and delivery of clear water vertical wet type submersible pump suitable for 100mm dia borewell conforming to IS 8034/2002 as amended thereafter and BEE 3 Star Rated capable of discharging noted LPM against head of water column due to all causes. The pump shall be with stainless steel shaft and dynamically balanced bronze or Cast SS impeller, brass screws and CI FG 200 grade pump bowl/diffuser with ISI mark. The pump shall be directly coupled to a continuos rated two pole suitable wet type vertical squirrel cage induction motor as per IS9283 /1995 and as amended thereafter, suitable for operation in AC three phase 415 V+/- 10 %, 50 HZ +/- 5 %

Labour charges for the erection of submersible pumpset in borewell/openwell including fixing and jointing submersible cable with proper clamps upto the starter to required depth and also fixing of riser pipes to the required depth valves erection clamps, pressure gauges upto the exterior wall of pump room and erection of panel board consisting of TPICN switches starter, Voltmeter, Ammeter, three pilot (indicating) lamps capacitor single phasing preventor, water level guard and laying and jointing the cables and twin earthing as per IE rules etc., complete and testing the pumpset and trail run for 10 days

Upto 5 HP

Above 5.00 HP to 10.00 HP

Supply and delivery of direct online starter confirming to IS13947, IEC60947-1 and as amended thereafter with suitable KW rating for operation in AC/Three Phase/50HZ (± 5%) and 415 V(±10%) including Ammeter, Voltmeter, Thermal Overload relay, 16 Amps 2 pole Magnetic Contactor with under Voltage protection, Indication lamp, starting capacitor, running capacitor and On/Off Push button switches, 5 way connector, wiring with 1 sq. mm/1.5 sq. mm copper PVC insulated cable, powder coated vermin proof box including the capacitor (the cost of capacitor is to be taken separately).

3phase panel board- DOL with two Level guard and auto start- 1HP

3phase panel board- star delta with two Level guard and auto start- 7.5HP

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Supply and Delivery and fixing of outside MS Ladder of 45cm clear wide made out of 50 mm x 50mm x 6mm MS angle for sides and steps in 16 mm MS plain rods fixed at 30cm C/C welded jointed etc ., providing with suitable side supports, clamps and locking arrangements provided with two coats of approved enamel paint over one coat of redoxide paint , for providing access to roof top of OHT of suitable inclined length , including bottom anchorage and transportation and as directed by TWAD Board officers. The rate includes concrete bed block in CC 1:2:4 using 20mm HBGS at top and bottom of suitable size with necessry anchor bolts.

Manufacturing, Fabrication, Supply and delivery of Aluminium ladder 6m height Folding type for operating inside the pumproom made out of Aluminium “ Џ “ channel 3” x 1 1/2” , 4mm thick for sides and steps in “L” channel 3” x 1 1/4” , 4mm thick @ 45cm width, 30cm c/c providing with suitable roller, rope, rubber bush etc. Including cost of all materials, labour etc. complete and as directed by TWAD Board officers.

Supplying and fixing in position of PVC Water Tank of approved by quality conforming to ISI specification 1000 litres capacity having suitable cover, bolt including cost of tab, taxes, transportation to work spot, fixing in position a place as shown and directed by the departmental officers including conducting required water test complete complying with standard specification.

Supplying and fixing New G.I pipe post using G.I pipe of approved quality and good variety ISI brand "B" class pipes of the following sizes for fencing post including cutting the pipe to required length fixing the pipe to plumb in the existing holes and laying the concrete. The rate is inclusive of cost of G.I pipes, including conveyance to work site and labour charges for cutting the pipe to required length and fixing in position as directed by the Departmental officers. etc., complete. (TNBP N. 86 ) 50 mm dia G.I pipe post. (M-0434 )

Supplying and fixing new 6 mm thick M.S chain link fencing of approval gauge with angle above ground level and tying the same with an angle including the cost of MS flat making holes on the flat cost of bolt nut 40 nos washer etc to size of the chain link fenching is 2 " x 2" x 10 gauge

Supplying fabricating and erecting welded and/or bolted and/or riveted steel work in built up sections, trusses and framed work, staging, racks, Height Gauge etc. for Steel Structures other than bridge girders, using RSJ, tees, angles and channels/flats, plates, gussets, round or square bars, cleats, bolts etc., including cutting, bending, straightening, drilling, riveting, hoisting, fixing, erecting, welding, bolting etc., with Providing stiffeners wherever required as per approved drawing including applying a priming coat of a approved steel primer with all materials, labour, tools & plants, lead & lift etc., complete as per specification and as directed by Engineer-in charge.

For MS Channels

For MS Angles

For MS Pipes

Providing and fixing Bitumen Pad for Expansion joint in between pavement slabs to 12mm thick and fixed as shown in the drawing including cost and conveyence of expansion joints including shalimar pad and joint sealent etc, complete as per standard specification

Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum- Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories. (a) MS Skid - 1 No. (b) Media 11054 No. Vessel with 20 nb Multiport Valve (with Media Pubble and Fine Sand and Activated Carbon Filling) set (c) Feed Pump 0.50 HP – 1 No. (d) Vertical Pump 2-9, 2.00 HP / Single Phase – 1 No. (e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos. (f) Flow Meter - 1 No. 20 Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings. The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact.

Supply of Wall Mount Chimney model of CNY bolt FL SW SC BK 0.90m 1500 m3/hr 90cm including all cost and conveyence etc, Complete.

Supplying and laying of Interlocking Paver Block Stone 60mm thick Over a base layer of crushed stone sandfilling incl. Cost of materials laying and Labour charges etc complete complying with the standard specification and as directed by the departmental officers.

Supplying and Fixing and roofing with colour galvalume sheet of 0.47mm thick with all necessary accessories such as J/V bolt and nuts of suitable length with suitable bitumen washers complete complying with standard specification and as directed by the departmental officers.

Picking the existing old mettaled surface from 50mm to 80mm thick surface without damaging the exisiting base course and cleaning the site etc, complete

Providing and laying, spreading and compacting graded stone aggregate to Wet mix macadam (WMM) specification including premixing the material with water at OMC in mechanical mix plant carriage to mixed material by tipper to site laying in uniform layers with paver in sub base / base course on well prepared surface and compacting with vibratory roller to achive the desired density complete as per clasue 406 of MORTH specifications.

Providing and laying Prime coat of 7 kgs/10 sqm over the WMM surface treated with primer using 7 kgs of bituminous Emulsion (SS) for 10square meter area including cost of bituminous binder, including labour charges for applying the required quantity of bituminous binder as Prime coat manually etc., complete as per 502 of MORTH Rev-5 Specifications

Providing and laying tack coat of 2.5 kgs/10 sqm over the WMM surface treated with binder using 2.5 kgs of bituminous Emulsion (RS) for 10square meter area including cost of bituminous binder, including labour charges for applying the required quantity of bituminous binder as tack coat manually etc., complete as per 503 of MORTH Rev-5 Specifications

Providing and laying Tack Coat over Dry Lean Cement Concrete surface using 3.00Kg of Bitumen Emulsion (RS1)per 10 sqm for preparatory to another bituminous construction over it including cost of material, labour charges, rentals for machinery,fuel and all other incidental charges etc., complete as per Clause 503 of MORTH Rev-5

Providing and laying 50mm consolidated thick Bituminous Macadam using 0.20cum of 26.50-13.20mm, 0.43 cum of 13.20-2.36mm and 0.08 cum of 2.36mm & below and with 37Kgs of VG30Grade bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing the min. required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to worksite, spreading the mix to uniform thickness of 50mm with paver to the specified grades and cross sections and consolidated by 8-10 tonne Vibratory Roller to the required density etc., including labour for attending to paver at site etc., including hire charges and fuel charges for 20- 30t CMP with bitumen boiler, tipper trucks, Paver Finisher, Vibratoryrollers and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 504 MORTH Rev-5

BITUMINOUS CONCRETE 30/40 MM THICK USING cmp (Grade-II) Providing and laying Bituminous Concrete to 25/30/40mm thick using 0.13 cum of 19.00- 9.50mm, 0.17 cum of 9.50-2.36mm and 0.26 cum of 2.36 and below with 50.30kgs of VG30 bitumen for premixing per 10sqm including cost and conveyance of all materials to CMP site, heating the bitumen and aggregate to required temperature and mixing them in required temperature in central hot mix plant 20-30 ton capacity, conveying the mix by tipper trucks to paver site, spreading the mix to uniform thickness of 40mm with mechanical paver to the specified grades and cross sections and consolidated by 8-10 tonne Vibratory to the required density etc., including labour for attending to paver to site etc., including hire charges and fuel charges for 20-30 t CMP with bitumen boiler, tipper trucks, Paver Finisher, Vibratory roller and all other tools and plant required, including fuel and all other incidental charges etc., complete as per specification using CMP as per clause 507 of MORTH Rev-5

Supply and fixing of Kilometre stone of standard design and drawing as per IRC:8-1980 (second revision),including painting and numbering etc., and all other incidental charges etc., complete.

Providing and laying of Gravel including cost and conveyance of the same to work site from approved quarry including stacking the same to departemental gauge for premeasurement including all labour charges for laying, spreading, including all hire and fuel charges for power roller for compaction, etc., complete and as directed by the departmental engineers for making up of low berms

Supplying and fixing in position 32mm dia Ball Valve of approved quality conforming to BIS etc., Complete complying with standards specification ( The 32mm dia Ball Valve should be got approved by the excutive engineer before use on works )

Supplying and Erecting 1.00 H.P monoblock with ISI mark with necessary accessories ( Motor should be got approved by the excutive engineer before use on works ) Complete complying with standards specification

Supplying and fixing in position PVC Screw Down Tap Heavy Type 15mm dia of approved quality conforming to BIS etc., Complete complying with standards specification ( The 6mm PVC Tap should be got approved by the excutive engineer before use on works )

Supply & stacking of red earth at site to the departmental guage for pre-measurements which is of light textured, crystalline, porous and friable and not of generally acidic or neutral but not of alkaline and should be fertile, including seignior age charges, cost of transportation, loading, unloading, stacking and inclusive of all taxes etc., complete.

Supply of Vermicompost in powder form, devoid of impurities and other materials, nutrient dense and which supports plant growth including cost of transportation

Planting of Ficus black ornamental foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges,transportation, stacking of saplings at site, earthwork excavation of required size, planting ofsapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Nerium oleander dwarf foliage shrub variety of height 30-45 cm in polythene bag of size6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Jasmine Plant foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges,transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Ixora ordinary foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting ofsapling, refilling of excavated earth etc as directed by the site in-charge.

Planting of Murraya exotica foliage shrub variety of height 30-45 cm in polythene bag of size 6x8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supply and planting of Shade grass including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, Supply and planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supplying and Planting of Ashoka tree sapling of height 180 - 240 cm in polythene bag of size 15x16 inch including supporting stack of 5 cm dia casurina pole of 10 feet height, including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supply and planting of Washingtoniafilifera ornamental foliage palm of height 120-150cm in polythene bag of size 21×21 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling,refilling of excavated earth etc as directed by the site-in-charge.

Supply and planting of Leucophyllumfruitescens ornamental specimen plant of height 90-120cm in polythene bag of size 21×21 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling, refilling of excavated earth etc as directed by the site-in-charge.

Supply and planting ofCassia alataornamental foliage tree of height 30-45cm in polythene bag of size 7×8 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the sitein-charge.

Supply and planting of Bougainvillea dwarfornamental foliage shrub of height 30-45cm in polythene bag of size 7×8 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling,refilling of excavated earth etc as directed by the site-in-charge.

Supply and planting of Burnfeisia pauciflora ornamental foliage shrub of height 30-45cm in polythene bag of size 7×8 inch including loading and unloading charges,transportation, stacking of saplings at site,earth work excavation of required size,planting of sapling,refilling of excavated earth etc as directed by the site-in-charge.

Supply of White Pebbles including cost of transportation

Planting of Bougainvillea hybrid foliage shrub variety of height 30-45 cm in polythene bag of size 6x7 inch including loading and unloading charges, transportation, stacking of saplings at site, earth work excavation of required size, planting of sapling, refilling of excavated earth etc as directed by the site in-charge.

Supply, Installing, testing and commissioning of Stainless Steel Corrugated Flexible Braided Pipe (Hose) for dropping sprinklers below false ceiling. Pipe shall be 16 bar pressure rating and 1000mm long, 25mm dia with union / reducer, collar, clamps, etc. It shall have UL listed and FM approved

Supply and delivery of 120 Lit Capacity Mobile Garbage Bins shall conform to following specifications:-G• The material shall be heat and chemical resistant and shall be UV stabilized. The manufacturing process shall be Injection molding only as specified by EN 840-1 standard. The bins shall have suitable lid of HDPE Injection Molded at the top which shall be hinged on one side and open easily by gravity while unloading in refuse compactors. The bins shall have Nominal volume of 120 Ltrs. The bins shall have Two Solid rubber wheels of 200 mm Dia. (+-5 mm). Both these wheels shall be mounted on axle, which shall be corrosion resistant. The bins shall be provided with single piece pulling handle. The bins shall have deep and strong combs as per EN Standards. These combs shall ensure optimum accommodation on the lifting devices i.e. Refuse Compactors with Universal Bin Lifting mechanism. The useful load shall be min. 110 Kgs. As per EN standard. The color of the bins shall be Green/Blue/Grey/Yellow/Red and aesthetically pleasant in nature

Manufacturing, supplying and erection of AIR WALKER with following specification:- Main Post : 114mm OD GI “B” Class Pipe Supporting pipe : 32& 38mm GI “B” Class Pipe Foot Rest : LLDPE Movements :Smooth bearing movement Safety : No sharp edges Powder coating : UV 7 tank powder coating Area required:5X4’

Manufacturing, supplying and erection of Dip & Hip with following Specification: Main Post : 114mm OD GI “B” Class Pipe Supporting pipe : 32& 38mm GI “B” Class Pipe Foot Rest : LLDPE Movements :Smooth bearing movement Safety : No sharp edges Powder coating : UV 7 tank powder coating Area required:6’X4’

Manufacturing, supplying and erection of Hyper extension with following Specification : Main Post : 114mm OD GI “B” Class Pipe Supporting pipe : 32& 38mm GI “B” Class Pipe Chest Rest : LLDPE Movements :Smooth bearing movement Safety : No sharp edges Powder coating : UV 7 tank powder coating Area required:4’X3’

Manufacturing, supplying and erection of DIPPING with following Specification : Main Post : 114mm OD GI “B” Class Pipe Supporting pipe : GI 38mm OD GI “B” Class Pipe Safety : No sharp edges Powder coating : UV 7 tank powder coating Certification : ISO and NSIC certification Area required:8’X3’

Manufacturing, supplying and erection of DOUBLE TWISTER with following Specification : Main frame : 114mm OD GI “B” Class Pipe , Supporting pipe : 32& 38mmOD GI “B” Class Pipe. Twister : 2 nos of LLDPE Twister Movements : Smooth bearing movement Safety : No sharp edges Powder coating : UV 7 tank powder coating Area required:6’X6’

Manufacturing, Supplying and fixing of Topeiary Green miniature made up of fibre glass/ ferro cement / M.S steel gauge with turf for garden and outdoor which is aesthetically present in nature and rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance etc

Canteen Dining Tables (1.5 m × 1.0 m) • Size: 1.5 × 1.0 × 0.75 m • Steel frame with laminated wooden top • Heat & stain-resistant surface, PVC edge band • Capacity: 4–6 seater • Color: Standard or custom • Warranty: 1 year

Canteen Chairs • Stackable, heavy-duty, easy-clean design • Powder-coated MS tubular frame • Polypropylene or cushioned seat/back • Color: Standard or custom • Warranty: 1 year

Renewal Stone Water Falls Existing Fountain Work For Civil Work, Natural Stone, Under water Light, Plumping and Electrical Works, Pumb and Pannel Board 5Hp including all cost and conveyence etc, Complete.

Renewal FRP Statue Water Falls Existing Fountain Work For Civil Work, FRP Statue, Under water Light, Plumping and Electrical Works, Pumb and Pannel Board 7Hp including all cost and conveyence etc, Complete.

Renewal Forrest Water Falls Existing Fountain Work For Civil Work, Natural Stone, Under water Light, hpPlumping and Electrical Works, Pumb and Pannel Board 7Hp including all cost and conveyence etc, Complete.

Renewal Statue Water Falls Existing Fountain Work For Civil Work, Statue, Under water Light,Form Nozil, Plumping and Electrical Works, Pumb and Pannel Board 5 Hp including all cost and conveyence etc, Complete.

Renewal Statue Water Falls Existing Fountain Work For Civil Work, Statue, Under water Light,Form Nozil, Plumping and Electrical Works, Pumb and Pannel Board 7 Hp, G.I Pipe for Fountain and Nozil including all cost and conveyence etc, Complete.

Renewal Statue Water Falls Existing Fountain Work For Civil Work, Statue, Under water Light,Form Nozil, Plumping and Electrical Works, Pumb and Pannel Board 5 Hp including all cost and conveyence etc, Complete.

"Supplying, erecting and Fixing precast reinforcement bench with back rest.Bench shall consist of 2 nos. L shaped bases support in natural cement color of thickness 100mm, back height 1000mm,front height 450mm, base width 620mm and 5Nos Reinforced Concrete planks in red color and size of 1500x100x50mm and 1no.reinforced concrete plank of 150x200x50mm:manufactured by using M-30 grade concrete & reinforced suitably: all parts to be joined with galvanized nuts and bolts of suitable size."(HC-W0302)

See- Saw Four Seated:Manufacturing, supply and erection of See Saw Four Seated made up of size 2.10 Mt long and 1.5 Mt width supporting with 35 mm dia of C.R pipe of “B” class thickness and 4 nos. of seat arrangements, one safety back rest up & down movement will be controlled by heavy duty bearing mounting including one coat of red oxide and two coat of best enamel with foundation clamps etc, complete.

Slide with Ladder: Manufacturing, supply and erection of Slide with ladder made up of “B” class C.R pipes 32 mm, 38 mm and 25 mm size. Sliding length 2.4 mt, height 1.82 mt and width 508 mm including one coat of anti-rust epoxy primer and two coat of multicolor enamel coating for glazy finish with foundation clamp etc,complete

Arch Frame Swing Four Seats: Manufacturing, Supply and erection of Arch Frame Swing four seats made of B class GI pipes of sizes of 50mm dia. The main frame supported by three numbers of Arch 8 feet height and four seats are mounted in the main bar. Heavy duty tested chains are used for seating arrangements. Size: 8 feet height x 5 feet width x 16 feet breadth including one coat of antirust poly urethane primer and two coat of multicolor poly urethane coating for glazy finish with foundation clamp etc, complete.

Horse Shaped Merry Go Round:Manufacturing, supply and erection of Horse Shaped Merry Go Round – made of “B” class C.R pipe sized of 35mm, 25mm, 20mm and 100mm. Size of 1.5-meter dia made up of center post 100mm dia and two sides smooth ball bearings and side support of 25mm dia of ‘B’ class C.R. pipe with duck shaped seats 4nos. including one coat of anti-rust epoxy primer and two coats of multicolor epoxy coating for glazy finish with foundation clamps etc, complete.

Manufacturing, supply and erection of Swing Double Seat made of 50mm, 63.5mm B class C.R pipes.Dimensions height -3.048-meter, Length – 3.048 meters. Tested bearing supported molded chains with attractive colors. Seating arrangements made by GI sheet including one coat of anti-rust poly urethane primer and two coat of multicolor poly urethane coating for glazy finish with foundation clamp etc,complete.

C90 spotting scope 1250mm FL Magnification:39 x (with included eyepiece)Objective Lens Diameter:90mm (3.54″)Eyepieces:32mm Plössl (1.26″)Angular Field of View:1.3° with included eyepieceLinear Field of View (@1000 yds)/@1000m):68 ft (20.7 m) with included eyepieceFocal Length:1250mm (49″)

Supply of NP3 Class RCC Pipe conforming to IS 458/2003 including cost of pipe as a finished work including all other incidental charges, testing charges including loading, unloading, transport and delivery in good condition at work site etc., complete, as directed by the Departmental Officers and as per standard specifications.

Please Enable Macros to View BoQ information