SPECIAL REPAIR TO BUILDING NO P-59 UNDER GE (SOUTH) MAMUN AT MAMUN MIL STN

Amount

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M&L for Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates using steel conforming to grade Fe- 290 (Gde E- 165) incl 02 coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 incl 02 coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coveringscomplete all as speecified and directed.

M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering/cladding to wall, (maximum height upto 10m) fixed with self tapping screws complete all as speecified and directed. [Note : The colour of sheet shall be as approved by GE ]

M&L for Plain, galvanised, mild steel sheeting 1 mm thick as in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 for collection of rain water at a height of 15m fixed with self tapping screws washers etc & other necessary fitting as reqd at site complete all as speecified and directed.

M&L for Rain water pipe of size 100 x 100 mm with using Plain, galvanised, mild steel sheeting 1 mm thick made with shape including joining welding cleats , rivetting, cutting to required shape & fixing the pipe in existing valley gutter on one end incl cutting of valley as per site requirement complete all as speecified and directed.

M&L for 60mm thick factory made rubberised coloured (laminated) interlocking paver block (using vibro compaction method) (topping thickness not less than 5mm) in white cement and non fadable glossy pigment of approved shade of any shape and size conforming to IS-15658-2006 of M-35 grade laid over & including cleaned dry sand cushion 50mm thick over and including 75mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) including demolition of damaged cement concrete of any type or description and removal of debris out off the premises etc complete all as specified and directed.

M&L for Cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) such as in column for fixing of truss, benching, coping, Bed blocks and the like, rounded or chamfered on edges including necessary formwork including demolition of existing concrete of any description and removal of debris out off the premises complete all as specified and directed.

M&L for rendering 10mm thick on brick work or concrete surface in CM (1:6) on wall surfaces finished even and smooth using extra cement including taking down cement or cement lime plaster of any description and raking out joints, hacking for key, scrubbing down with water and removal of rubbish, out off the premises complete all as specified & directed.

S&F ALCO panel (Aluminium composite panel) 4mm thick for fixing in Aluminium frame for partition and the like, complete all as specified & directed.

M & L for 5mm thick Colour printed solid PVC sheet as in wall panelling/lining for fixing on Brick masonary wall and solid PVC Partitions inclusive of 5mm thick and 35mm wide vertical PVC beading fixed with machine screw with a horizontal spacing of 300mm c/c at site incl demolition of existing lining of any description complete all as specified and directed.

M&L for Bird proofing spikes of material polycarbonated plastic/PVC, Pesticide free, high quality spike for pigeon/bird ledge protection upto 150mm, length of spike should not be less than 75mm fixed to steel member/masonary work with and incl necessary adhesive/tape/screw etc at height around upto 10m including necessary scaffolding including taking down existing spikes, complete all as specified and directed.

S&F Zebra Blinds for windows incl all accessories complete all as specified and as directed.

S&F vertical Blinds for windows incl all accessories complete all as specified and as directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for RCC( 1:1.5:3) type A-1 using 20mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary formwork complete all as specified and directed.

M&L for Granite (of any type) tiles 18mm to 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over & including laid over and including 15mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed.

M&L for 20mm thick PVC shutter, printed one side with one coating of ultra voilet chemical, glossy/mat finish incl 100% termite proof/water proof, fire resistant, ECO friendly, weight not less than 12 Kg per Sqm complete all as specified and directed.

All as per Ser item No 19 but without coating of ultra voilet chemical complete all as specified and directed.

S & F for Continuous (piano) hinges, with width of flap 30 mm mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F for 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finishedcomplete all as specified and directed.

S&F for Hasp and staple, safety type of size 100 mm , brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

M&L for Ball catcher with proper magnetic effect fixed with shutter complete all as specified and directed.

M&L for 0.80mm thick PVC edge binding tape around the 20mm thick PVC shutter edge, complete all as specified and directed. Make : Polycon, HR Enterprises, Kumar Tech

S&F for stainless steel plain basket of size 17" x 20" x 6" complete all as specified and directed. Make : Silkmove/Homecare/Hatic

S&F for stainless steel partition of size 17" x 20" x 6" complete all as specified and directed. Make : Silkmove/Homecare/Hatic

S&F for stainless steel cutlery of size 17" x 20" x 6" complete all as specified and directed. Make : Silkmove/Homecare/Hatic

S&F for stainless steel grain trolly with stand of size 21" x 17" x 10" complete all as specified and directed. Make : Silkmove/Homecare/Hatic

S&F for stainless steel cup & soucer of size 17" x 20" x 4" complete all as specified and directed. Make : Silkmove/Homecare/Hatic

S&F for stainless steel plate basket of size 17" x 20" x 6" complete all as specified and directed. Make : Silkmove/Homecare/Hatic

S&F for 20" long telephonic slider to facilitate drawer slide of steel ball bearing fixed with steel screws complete all as specified and directed. Make : Nixon/Rodal/Ozone/Ultima or equivalent

S&F for auto hinges for cabinet case complete all as specified and directed.. Make : Karf/Hetich

S&F 150mm size stainless steel bright finish handle for cabinet/cup board shutter complete all as specified and directed..

M&L for anodised aluminium frame for doors,windows, ventilators and partition walls with one or more rebates including joining cleat rubber packing & strips etc for fixing glass & Alco panel into the frame for fixing incl Powder Coating (minimum thickness of powder coating 50 micron) complete all as specified and directed. Note: S&F of Glass Panes & Alco panel shall be measured & paid seperately under relevent items of this BOQ)

S&F 5.5 mm thick Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane for fixing in aluminium partition and the like complete all as specified and directed.

S&F 5.5 mm thick Sheet glass,ordinary quality and glazing with oil putty in square exc 0.5 sq. m in each pane for fixing in aluminium partition and the like complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of distemper oil emulsion (OBD) over a coat of primer as per manufacturer instructions (from same manufacturer of OBD) over a layer of wall care putty 2 mm thick complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall & applying two coats of cement base paint over a coat of primer as per manufacturer instructions complete all as specified and directed.

M&L for 5 mm thick PVC sheet fillet of width 35 mm for wall paneeling inclusive of fixing on to wall to make PVC frame as per specifications and drawing complete all as specified and directed.

Taking down carefully unserviciable/ damaged copper/aluminium surface (batten/coduit or casing caping) point wiring any length for light/fan/socket or power including unscrewing from board (fitting and fixture such as switches, sockets, ceiling rose, lamp holders, brackets, pendent, regulators, sockets, Bracket /sketch fitting etc ) and removing material from site and making good to the disturbed surface to match with existing finish complete all as specified and directed.

M&L for Modular Point wiring using FRLS PVC insulated unsheathed /multi stranded copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box and approved make sunken modular metal flush gang box and suitable support frame and cover plate (inner/outer) of required modules for mounting modular switches/ sockets etc, connecting earth including cutting groove for concealed wiring, making good to disturb surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc (conduit shall be fixed on surface of ceiling with necessary saddles where concealing of conduit is not feasible), for light/fan/bell point complete all as specified and directed. (Note : Modular switch/bell push/fan regulator etc shall be measured and paid separately under respective items.)

All as per Srl item No. 42 above but for 5 pin 5 Amp socket outlet point on independent gang box and suitable support frame and cover plate (inner/outer) controlled by one switch 5Amp one way, etc complete all as specified and directed.

All as per Srl item No. 42 above but for 5 Pin 5 Amp socket outlet point on same board controlled by one switch 5 Amps one way on same gang box support frame and cover plate etc complete all as specified and directed.

All as per Srl item No. 42 above but for one 15Amp socket outlet point concealed using 2.5Sqmm FRLS PVC insulated multi-strand copper conductor wire including 1.5Sqmm FRLS PVC insulated unsheathed copper conductor earth wire and making good to disturbed surfaces of wall floor to match existing finishes complete all as specified and directed.

S&F Modular Socket outlet, 5 pin, multi purpose 2 module 6 Amps, AC 230 volts, etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVKSWW065 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

S&F Modular Switch 1 way 6/10 Amps , 1 module etc complete all as specified and directed. Make : Crabtree (Verona) Cat Part No : ACVSXXW101 or equivalent of Legrand/Siemens/Schenider/Anchor Roma.

S & F modular switch piano type flush button 16 Amp one module, complete all as specified and directed. Make : Legrand Cat Part No 673009/Crabtree Cat Part No ACMSXXW102/Anchor Roma Cat Part No 66104.

S&F Ceiling rose polycarbonate isolated body surface Bakelite, not less than 50x20mm, three terminals, AC 230 volts etc complete all as specified and directed. Make : Anchor (Penta) Cat Part No : 39040 or equivalent of Havells(Reo)/SSK (Topline)/GM (Vyoma)

S & F Fan regulator modular step type suitable for 1200/1400mm sweep ceiling fan hum free, 120W- 2 module including necessary connections complete all as specified and directed. Make : Legrand Cat Part No 673028/Crabtree Cat Part No ACARFHW005/Anchor Roma Cat Part No 66502.

S&F Surface mounted 1x20 watt LED tube light fittings (4 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

S&F Surface mounted 1x10 watt LED tube light fittings (2 feet long), prewired, decorative luminaire with inbuilt LED tube rod and acrylic end covers with all accessories and PVC Round/Square block for fixing of fittings and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose/PVC connector to light fitting and testing etc complete all as specified and directed.

S&F in replacement recess mounting LED flat panal 2'x2' made of CRCA sheet duly power coated with High effcient 36 watt LED complete with all accessories inernely pre-wired and including connecting up with three core twisted flexible copper conductor cable of suitable size complete all as specified and directed.

Taking down ceiling/exhaust fan of any sweep & size and refix in same position after overhauling including minor repairs by replacement of capacitor, safety pin, cap, nuts & bolts etc and making connection using 3 core, 0.50 Sqmm PVC insulated and overall sheathed flexible copper conductor cable from ceiling rose to fan, including testing to ensure efficient functioning including application of one coat of synthetic enamel paint by spray painting & rewriting number complete all as specified and directed.

S&F Lamp holder insulated body with back plate suitable for batten fitting including 12W LED lamp of approved make and cat part and PVC Round/Square block etc complete all as specifeid and directed.Notes : Notes for Srl item No 51 to 55:- 1. Driver shall be potted antivibration type. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be povided. 3. CRI (Colou Rendring Index) of fixture shall be > 70. 4. CCT (Colout Correlated Temprature of fixture shall be 5700K ± 300 K. 5. System Lumen Efficacy shall be > 100Lm/W 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 5 years gurantee shall be provided by contractor suppoted by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the Contractor shall replace / repair the defective fitting within 07 Days after handing over to Contractor for replacement / repair 11. CA No shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintaince required, if any can be carried out from Top cover.

S&F Double door MCB DB SPN, 240 Volts, 08 Way made out of CRCA powder coated sheets, IP43 protection with copper bus bar including taking out old unsv DB any size/type, complete all as specified and directed. Make: Legrand Cat Part No 6077-11 or equivalent model in L&T/Hager/SCHNEIDER

S&F for MCB single pole (SP) 240 volts, 6 to 32 Amps, 10KA (C-series) , complete all as specified and directed. Make : Legrand/Schneider/Hager

S&F for MCB single pole neutral (SPN) 240 volts, 6 to 32 Amps, 10KA ((C-series) complete all as specified and directed. Make : Legrand/Schneider/Hager

M&L for Sub main wiring with FRLS PVC insulated unsheathed 2X6 sqmm multistranded copper conductor cable 1100 V with 1X6 sqmm FRLS PVC insulated green multistranded copper cable for continuous earth drawn through & including concealed PVC conduit of appropriate size not less than 20 mm dia & 1.8mm wall thickness with all accessories including cutting grooves and making good disturbed surface to match existing including taking down existing surface sub main wiring complete all as specified and directed. (Note: Two runs of FRLS PVC cable with one run of earth conductor and conduit shall be measured as one RM.) Make for wire : Polycab/Anchor/Finolex

M&L for earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, HDPE pipe 15mm bore as protection pipe, GI watering pipe 20mm bore light grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is deemed included in unit rate quoted by the contractor. 2. Earth filling shall be done by vegitable soil. 3. Soil shall be free from stone, boulders, aggregate, gravels .

M/S INDIAN ELECTRICAL

AV ENTERPRISES

Alishan Builders

A V BUILDERS

KULBHUSHAN AGGARWAL

WALIA ENTERPRISES

GANDOTRA CONSTRUCTION CO