Loading
Loading…
Loading…
Tender Value
₹46.0 L
EMD Value
₹92,500
Closing Date
9 Oct 2026, 6:00 pm
GE AF MARATHAHALLI WIND TUNNEL ROAD, KEMPAPURA, YE
GE AF MARATHAHALLI WIND TUNNEL ROAD, KEMPAPURA, YEMALUR POST, BANGALORE. PIN- 560037
PROVISION OF 30 KVA UPS BATTERIES AT PATH LAB P-13 AND SPECIAL REPAIRS/REPLACEMENT TO EXTERNAL ELECTRIFICATION AND LT PANELS AT IAM UNDER GE (AF) MARATHAHALLI BANGALORE.
2026_MES_790040_1
GE (AF) MARATHAHALLI / 8874 / E8
Open Tender
Civil Works
Item Rate
180 days
GE AF MARATHAHALLI WIND TUNNEL ROAD, KEMPAPURA, YE
AS PER ENIT
7 documents required · 7 mandatory
₹500
GE AF MARATHAHALLI WIND TUNNEL ROAD, KEMPAPURA, YE
₹92,500
Yes
18 Sept 2026
18 Sept 2026
11 Oct 2026
18 Sept 2026
9 Oct 2026
2 Oct 2026
20 Sept 2026 - 29 Sept 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | Supply, installation, testing and commissioning of outdoor type KIOSK panel board suitable for 3 phase 4 wire 415 V, 50 Hz and tested at CPRI for 415 volts factory fabricated in an approved factory having modern fabrication process powder coating in approved shared having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS : 8623/93 comprising. The outer shell shall be made out of 3.15 mm thick CRCA sheet and MS angle section 40x40x6 mm base frame factory fabricated with front and back openable, double door system lockable/ open able. The bottom of the outer shell contains a detachable plate having size with glands. The outer shell shall be mounted on stand having zine coating not less than 80 microns. Provision of threaded earthing stud at bottom and lifting lugs of suitable size at top to lift the panel safely shall be made. The degree of protection of outer shell shall be IP - 54. Inner shell shall be made out of 2.0 mm thick CRCA sheet duly compartmentalized for each control gear, TPN alluminum bus bar of rating not less than the 1.5 times the rated capacity of the incomer MCCB. The TPN bus bar shall be insulated with colour coded heat shrinkable sleave. All control wires shall be with 2.5 sqmm multi strand copper conductor and shall be propely bunched, tied, ferruled for proper identification and crimped with adequate size of lugs, incl all MCCBs/MCBs with rotary handle in LT Panel all as specified and directed by Engr in charge. | 1 | Job | 1.25 | ₹1.25 |
| 1.01 | INCOMING
(a) MCCB 4 pole, 63 Amps, 25 KA - 01 No
(b) Intelligent AC digital display three phase LCD ammeter 0 to 630A and voltmeter 0 to 500V with CT
(c) Indication lamp RYB/RRR-set of 03 -01 No
OUTGOING
(a) MCCB 4 pole 40 Amps 16 KA 415 Volt -3 No
(b) MCCB 4 pole 32 Amps 10 KA 415 Volt - 1 Nos | - | - | - | - |
| 2 | Supply, installation, testing and commissioning of outdoor type KIOSK panel board suitable for 3 phase 4 wire 415 V, 50 Hz and tested at CPRI for 415 volts factory fabricated in an approved factory having modern fabrication process powder coating in approved shared having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS : 8623/93 comprising. The outer shell shall be made out of 3.15 mm thick CRCA sheet and MS angle section 40x40x6 mm base frame factory fabricated with front and back openable, double door system lockable/ open able. The bottom of the outer shell contains a detachable plate having size with glands. The outer shell shall be mounted on stand having zine coating not less than 80 microns. Provision of threaded earthing stud at bottom and lifting lugs of suitable size at top to lift the panel safely shall be made. The degree of protection of outer shell shall be IP - 54. Inner shell shall be made out of 2.0 mm thick CRCA sheet duly compartmentalized for each control gear, TPN alluminum bus bar of rating not less than the 1.5 times the rated capacity of the incomer MCCB. The TPN bus bar shall be insulated with colour coded heat shrinkable sleave. All control wires shall be with 2.5 sqmm multi strand copper conductor and shall be propely bunched, tied, ferruled for proper identification and crimped with adequate size of lugs, incl all MCCBs/MCBs with rotary handle in LT Panel all as specified and directed by Engr in charge. | 1 | Job | - | - |
| 2.01 | INCOMING
(a) MCCB 4 pole, 400 Amps, 50 KA - 01 No
(b) Intelligent AC digital display three phase LCD ammeter 0 to 630A and voltmeter 0 to 500V with CT
(c) Indication lamp RYB/RRR-set of 03 -01 No
OUTGOING
(a) MCCB 4 pole 200 Amps 35 KA 415 Volt -1 No
(b) MCCB 4 pole 125 Amps 25 KA 415 Volt - 2 Nos
(c) MCCB 4 pole 63 Amps 25 KA 415 Volt - 1 Nos
(d) MCCB 4 pole 32 Amps , 10 KA, 415 Volt - 6 No | - | - | - | - |
| 3 | Supply, installation, testing and commissioning of outdoor type KIOSK panel board suitable for 3 phase 4 wire 415 V, 50 Hz and tested at CPRI for 415 volts factory fabricated in an approved factory having modern fabrication process powder coating in approved shared having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS : 8623/93 comprising. The outer shell shall be made out of 3.15 mm thick CRCA sheet and MS angle section 40x40x6 mm base frame factory fabricated with front and back openable, double door system lockable/ open able. The bottom of the outer shell contains a detachable plate having size with glands. The outer shell shall be mounted on stand having zine coating not less than 80 microns. Provision of threaded earthing stud at bottom and lifting lugs of suitable size at top to lift the panel safely shall be made. The degree of protection of outer shell shall be IP - 54. Inner shell shall be made out of 2.0 mm thick CRCA sheet duly compartmentalized for each control gear, TPN alluminum bus bar of rating not less than the 1.5 times the rated capacity of the incomer MCCB. The TPN bus bar shall be insulated with colour coded heat shrinkable sleave. All control wires shall be with 2.5 sqmm multi strand copper conductor and shall be propely bunched, tied, ferruled for proper identification and crimped with adequate size of lugs, incl all MCCBs/MCBs with rotary handle in LT Panel all as specified and directed by Engr in charge. | 1 | Job | 100 | ₹100 |
| 3.01 | INCOMING
(a) MCCB 4 pole, 160 Amps, 35 KA - 01 No
(b) Intelligent AC digital display three phase LCD ammeter 0 to 630A and voltmeter 0 to 500V with CT
(c) Indication lamp RYB/RRR-set of 03 -01 No
OUTGOING
(a) MCCB 4 pole 40 Amps 16 KA 415 Volt -6 No | - | - | - | - |
| 4 | Supply, installation, testing and commissioning of outdoor type KIOSK panel board suitable for 3 phase 4 wire 415 V, 50 Hz and tested at CPRI for 415 volts factory fabricated in an approved factory having modern fabrication process powder coating in approved shared having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS : 8623/93 comprising. The outer shell shall be made out of 3.15 mm thick CRCA sheet and MS angle section 40x40x6 mm base frame factory fabricated with front and back openable, double door system lockable/ open able. The bottom of the outer shell contains a detachable plate having size with glands. The outer shell shall be mounted on stand having zine coating not less than 80 microns. Provision of threaded earthing stud at bottom and lifting lugs of suitable size at top to lift the panel safely shall be made. The degree of protection of outer shell shall be IP - 54. Inner shell shall be made out of 2.0 mm thick CRCA sheet duly compartmentalized for each control gear, TPN alluminum bus bar of rating not less than the 1.5 times the rated capacity of the incomer MCCB. The TPN bus bar shall be insulated with colour coded heat shrinkable sleave. All control wires shall be with 2.5 sqmm multi strand copper conductor and shall be propely bunched, tied, ferruled for proper identification and crimped with adequate size of lugs, incl all MCCBs/MCBs with rotary handle in LT Panel all as specified and directed by Engr in charge. | 1 | Job | 53 | ₹53 |
| 4.01 | INCOMING
(a) MCCB 4 pole, 160 Amps, 35 KA - 01 No
(b) Intelligent AC digital display three phase LCD ammeter 0 to 630A and voltmeter 0 to 500V with CT
(c) Indication lamp RYB/RRR-set of 03 -01 No
OUTGOING
(a) MCCB 4 pole 63 Amps 25 KA 415 Volt -1 No
(b) MCCB 4 pole 40 Amps 16 KA 415 Volt - 4 Nos
(c) MCCB 4 pole 32 Amps , 10 KA, 415 Volt - 1 No | - | - | - | - |
| 5 | Supply, installation, testing and commissioning of outdoor type KIOSK panel board suitable for 3 phase 4 wire 415 V, 50 Hz and tested at CPRI for 415 volts factory fabricated in an approved factory having modern fabrication process powder coating in approved shared having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction confirming to IS : 8623/93 comprising. The outer shell shall be made out of 3.15 mm thick CRCA sheet and MS angle section 40x40x6 mm base frame factory fabricated with front and back openable, double door system lockable/ open able. The bottom of the outer shell contains a detachable plate having size with glands. The outer shell shall be mounted on stand having zine coating not less than 80 microns. Provision of threaded earthing stud at bottom and lifting lugs of suitable size at top to lift the panel safely shall be made. The degree of protection of outer shell shall be IP - 54. Inner shell shall be made out of 2.0 mm thick CRCA sheet duly compartmentalized for each control gear, TPN alluminum bus bar of rating not less than the 1.5 times the rated capacity of the incomer MCCB. The TPN bus bar shall be insulated with colour coded heat shrinkable sleave. All control wires shall be with 2.5 sqmm multi strand copper conductor and shall be propely bunched, tied, ferruled for proper identification and crimped with adequate size of lugs, incl all MCCBs/MCBs with rotary handle in LT Panel all as specified and directed by Engr in charge. | 1 | Job | 10 | ₹10 |
| 5.01 | INCOMING
(a) MCCB 4 pole 250 A 50 KA 415 Volts - 1 No
(b) Intelligent AC digital display three phase LCD ammeter 0 to 200A and voltmeter 0 to 500V with CT
(c) Indication lamp RYB/RRR-set of 03 -01 No
OUTGOING
(a) MCCB 4 pole 100 Amps 25 KA 415 Volt -2 No
(b) MCCB 4 pole 63 Amps 25 KA 415 Volt -6 No | - | - | - | - |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.30 MB
TENDER.pdf
Tender Documents • 0.52 MB
BOQ_885633.xls
BOQ • 0.48 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .