Loss Reduction Works under RDSS for South Zone

Amount

AB Cabling works ,33KV,22KV,11KV & LT Line overhead Line Ab Cabling & other Cabling Works as per technical specification, approved drawings and scope of work.

LT AB Cable

LT AB Cable on poles [Size: (3x95 Sq, mm ) +70sqmm(Insulated) +16 sqmm{Inclusive 3% sagging & wastage)

LT AB Cable on poles [Size: (3x95 Sq, mm ) +70sqmm(Insulated) +16 sqmm{Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

Anchoring Assembly for LT

Suspension Assembly for LT

Facade Hooks for LT

Distribution box 3 phase 5 connectors as per TS

Piercing Connector as per TS

Cable for SMDB 3.5Core X 35sqmm

LT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

LT , AB Cable (3x185 Sq. mm) +150sqmm(Insulated) +16 sqmm {Inclusive 3% sagging & wastage)

LT AB Cable on poles [Size: (3x185 Sq. mm) +150sqmm (Insulated)+16 sqmm {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

Anchoring Assembly for LT

Suspension Assembly for LT

Facade Hooks for LT

Distribution box 3 phase 5 connectors as per TS

Piercing Connector as per TS

Cable for SMDB 3.5Core X 35sqmm

LT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

LT ,AB Cable 3x240 Sq. mm+ 185sqmm(Insulated) +16 sqmm {Inclusive 3% sagging & wastage)

LT AB Cable on poles [Size: (3x240mm²) + 185sqmm (Insulated)+16 sqmm {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

Anchoring Assembly for LT

Suspension Assembly for LT

Facade Hooks for LT

Distribution box 3 phase 5 connectors as per TS

Piercing Connector as per TS

Cable for SMDB 3.5Core X 35sqmm

LT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

LT PVC Cable

LT XLPE Insulated PVC Sheathed 3.5 x95 Sq. mm Cabling Work {Inclusive 1% sagging & wastage)

3.5x95 mm sq XLPE Insulated PVC Sheathed Cable

LT Heat Shrinkable 4 Core Cable Straight Through Jointing Kit

LT Heat Shrinkable Outdoor type Termination kit

Distribution box 3 phase 5 connectors as per TS

Clamps Fittings

LT XLPE Insulated PVC Sheathed 3.5 x120 Sq. mm Cabling Work {Inclusive 1% sagging & wastage)

3.5x120 mm sq XLPE Insulated PVC Sheathed Cable

LT Heat Shrinkable 4 Core Cable Straight Through Jointing Kit

LT Heat Shrinkable Outdoor type Termination kit

Distribution box 3 phase 5 connectors as per TS

Clamps Fittings

LT XLPE Insulated PVC Sheathed 3.5 x240 Sq. mm Cabling Work {Inclusive 1% sagging & wastage)

3.5x240 mm sq XLPE Insulated PVC Sheathed Cable

LT Heat Shrinkable 4 Core Cable Straight Through Jointing Kit

LT Heat Shrinkable Outdoor type Termination kit

Distribution box 3 phase 5 connectors as per TS

Clamps Fittings

LT XLPE Insulated PVC Sheathed 3.5 x500 Sq. mm Cabling Work {Inclusive 1% sagging & wastage)

3.5x500 mm sq XLPE Insulated PVC Sheathed Cable

LT Heat Shrinkable 4 Core Cable Straight Through Jointing Kit

LT Heat Shrinkable Outdoor type Termination kit

Distribution box 3 phase 5 connectors as per TS

Clamps Fittings

LT XLPE

LT XLPE armoured 3.5 x240 Sq. mm Cabling Work {Inclusive 1% sagging & wastage)

3.5x240 mm sq XLPE armoured Cable

LT Heat Shrinkable 4 Core Cable Straight Through Jointing Kit

LT Heat Shrinkable Outdoor type Termination kit

Distribution box 3 phase 5 connectors as per TS

Clamps Fittings

HT Cabling

11kv HT AB Cable 3x95 + 70 (Insulated)Sq. mm {Inclusive 3% sagging & wastage)

11kv HT AB Cable 3x95 + 70 (Insulated) Sq. mm {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length [600 mm]

Half Clamp for Cross Arm

Anchoring Assembly for HT

Suspension Assembly for HT

Facade Hooks for HT

Heat Shrinkable Straight Through Jointing Kit

Cable Termination kit

T-Jointing kit

HT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

11kv HT AB Cable on poles [Size: (3x185 Sq, mm ) + 150 (Insulated) Sq. mm {Inclusive 3% sagging & wastage)

HT AB Cable on poles [Size: (3x185 Sq, mm ) + 150 (Insulated) Sq. mm {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length [600 mm]

Half Clamp for Cross Arm

Anchoring Assembly for HT

Suspension Assembly for HT

Facade Hooks for HT

Heat Shrinkable Straight Through Jointing Kit

Cable Termination kit

T-Jointing kit

HT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

11kv HT XLPE Cable 3x120 Sq. mm 95 sq.mm {Inclusive 1% sagging & wastage)

HT AB Cable on poles [Size: (3x120+95 Sq, mm ) {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length [600 mm]

Half Clamp for Cross Arm

Anchoring Assembly for HT

Suspension Assembly for HT

Facade Hooks for HT

Heat Shrinkable Straight Through Jointing Kit

Cable Termination kit

T-Jointing kit

HT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

Underground Cable XLPE

11kv HT XLPE armoured Cable underground cableing work {Inclusive 1% sagging & wastage)(size-3x120sqmm

11 kV XLPE armoured Cable [Size: (3x120 mm²) {Inclusive 1% wastage)]

11 kV Cable Straight Through Jointing Kit [Size: 3x120 mm²]

11 kV Cable Indoor Termination Kit [Size: 3x120 mm²]

11 kV Cable Heat Shrink Outdoor Termination Kit [Size: 3x300 mm²]

RCC Hume Pipe Dia-150 mm [Length- 2 M]

Collar RCC Hume Pipe 150 mm

RCC cable cover (2 feet long)

Sand Bag (50 Kg)

Route and Joint indicating stone

Inspection Chamber

GI Pipe earthing 40 mm x 2.5/3 m 'B' class

Pipe HDPE Size 150 mm

Lug AL Crimping 70 SQMM XLPE Single HOLE

Flat GI Size 25x6 mm

Cleat HDPE for Cable Support

G.I. Pipe 100 mm DIA 'B' CLASS

Flat GI Size 50x6 mm

Channel MS Size 75x40x6 mm

11kv HT XLPE armoured Cable underground cabling work {Inclusive 1% sagging & wastage) 11kv XLPE 3x240 sqmm

11 kV XLPE armoured Cable [Size: (3x240 mm²) {Inclusive 3% wastage)]

11 kV Cable Straight Through Jointing Kit [Size: 3x240 mm²]

11 kV Cable Indoor Termination Kit [Size: 3x300 mm²]

11 kV Cable Heat Shrink Outdoor Termination Kit [Size: 3x240 mm²]

RCC Hume Pipe Dia-150 mm [Length- 2 M]

Collar RCC Hume Pipe 150 mm

RCC cable cover (2 feet long)

Sand Bag (50 Kg)

Route and Joint indicating stone

Inspection Chamber

GI Pipe earthing 40 mm x 2.5/3 m 'B' class

Pipe HDPE Size 150 mm

Lug AL Crimping 70 SQMM XLPE Single HOLE

Flat GI Size 25x6 mm

Cleat HDPE for Cable Support

G.I. Pipe 100 mm DIA 'B' CLASS

Flat GI Size 50x6 mm

Channel MS Size 75x40x6 mm

11kv HT XLPEarmoured cable , 3x300 Sq. mm underground cableing work {additional 1% sagging & wastage)

11 kV XLPE armoured Cable [Size: (3x300 mm²) {additional 1% wastage)]

11 kV Cable Straight Through Jointing Kit [Size: 3x300 mm²]

11 kV Cable Indoor Termination Kit [Size: 3x300 mm²]

11 kV Cable Outdoor Termination Kit [Size: 3x300 mm²]

RCC cable cover (2 feet long)

Sand Bag (50 Kg)

Route and Joint indicating stone

Inspection Chamber

GI Pipe earthing 40 mm x 2.5/3 m 'B' class

Pipe HDPE Size 150 mm

Lug AL Crimping 70 SQMM XLPE Single HOLE

Flat GI Size 25x6 mm

Cleat HDPE for Cable Support

G.I. Pipe 100 mm DIA 'B' CLASS

Flat GI Size 50x6 mm

Channel MS Size 75x40x6 mm

Warning Tape (Printed PE UG utility protection)

11kv HT XLPE armoured Cable underground cableing work {additional 1% sagging & wastage)

11 kV XLPE armoured Cable [Size: (3x400 mm²) {additional 1% wastage)]

11 kV Cable Straight Through Jointing Kit [Size: 3x400 mm²]

11 kV Cable Indoor Termination Kit [Size: 3x400 mm²]

11 kV Cable Heat Shrink Outdoor Termination Kit [Size: 3x400 mm²]

RCC Hume Pipe Dia-150 mm [Length- 2 M]

Collar RCC Hume Pipe 150 mm

RCC cable cover (2 feet long)

Sand Bag (50 Kg)

Route and Joint indicating stone

Inspection Chamber

GI Pipe earthing 40 mm x 2.5/3 m 'B' class

Pipe HDPE Size 150 mm

Lug AL Crimping 70 SQMM XLPE Single HOLE

Flat GI Size 25x6 mm

Cleat HDPE for Cable Support

G.I. Pipe 100 mm DIA 'B' CLASS

Flat GI Size 50x6 mm

Channel MS Size 75x40x6 mm

22kv HT AB Cable 3x95 +70 (Insulated) Sq. mm {Inclusive 3% sagging & wastage)

22kv HT AB Cable on poles [Size: (3x95 +70Sq, mm ) {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length [600 mm]

Half Clamp for Cross Arm

Anchoring Assembly for HT

Suspension Assembly for HT

Facade Hooks for HT

Heat Shrinkable Straight Through Jointing Kit

Cable Termination kit

T-Jointing kit

HT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

22kv HT AB Cable on poles [Size: (3x185 Sq, mm ) + 150 (Insulated) sq.mm {Inclusive 3% sagging & wastage)

22kv HT AB Cable on poles [Size: (3x185 Sq, mm ) + 150 sq.mm {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length [600 mm]

Half Clamp for Cross Arm

Anchoring Assembly for HT

Suspension Assembly for HT

Facade Hooks for HT

Heat Shrinkable Straight Through Jointing Kit

Cable Termination kit

T-Jointing kit

HT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

Underground Cable XLPE

Underground Cable XLPE

22kV XLPE armoured Cable [Size: (3x120 mm²) {Inclusive 1% wastage)]

22 kV Cable Straight Through Jointing Kit [Size: 3x120 mm²]

22 kV Cable Indoor Termination Kit [Size: 3x120 mm²]

22 kV Cable Heat Shrink Outdoor Termination Kit [Size: 3x120 mm²]

RCC Hume Pipe Dia-150 mm [Length- 2 M]

Collar RCC Hume Pipe 150 mm

RCC cable cover (2 feet long)

Sand Bag (50 Kg)

Route and Joint indicating stone

Inspection Chamber

GI Pipe earthing 40 mm x 2.5/3 m 'B' class

Pipe HDPE Size 150 mm

Lug AL Crimping 70 SQMM XLPE Single HOLE

Flat GI Size 25x6 mm

Cleat HDPE for Cable Support

G.I. Pipe 100 mm DIA 'B' CLASS

Flat GI Size 50x6 mm

Channel MS Size 75x40x6 mm

Conversion LT to HT

LT to 22kv New Line on Steel Tubular Pole with Rabbit Conductor -50Sq. mm

ACSR 6/1/3.35 (50mm²) {Includes 3 conductor lengths for 3Φ and Inclusive 3% (Sag, Jumpering and wastage}

11M Steel Tublar Pole (11 m, Working Load > 227 kgf/m²) (with Ruling Span 90 m, 8 No. Run thro' and 3 No. Double Pole Dead End Structures)

Muffs with concerete filling

Cross Arm: [Channel Iron (100x50x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators with GI Pin(Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

22 kV Pin Insulators (Porcelain, 24 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (1No. / Single Pole , 4 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 4 No; On Run Thro' structure: 2 No ]

Full clamps: [On Double Pole Dead End structure: 4 No, Single Pole Run Thro' structure: 2 No]

Danger Plate

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

LT to 22kv New Line on STP with rabbit Conductor -50 Sq. mm

ACSR Rabbit 50mm²) {Includes 3 conductor lengths for 3Φ and Additional 1% (Sag, Jumpering and wastage}

Steel Tubular Pole 11 Mtr long

Muffs with concerete filling

X-Arms: [MS Channel Iron (125x65x6 mm, Length: 2000 mm i/c tolerance 100 mm on either side] x 10 No. Structures

Pin Insulator

Knee bracing Set

Belt Set - MS Angle Iron: 65x65x6, Length:(1800 mm) x 2 No.

X-Bracing Set - MS Angle Iron: 50X50x6, Length [2700 mm) x 2 No.]

X-Arm (Horizontal) - MS Channel Iron: (125x65x6 mm), Length: 2600 mm i/c tolerance 100 mm on either side x 2 No.]

Disc insulator String (Strain) sets: 2 No. Discs in each string: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (Single Circuit: 3 No. conductors) x (2 No. sides) /Dead Structures

33 kV Pin Insulators (Porcelain, 36 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (2 No./Run Thro & 5 No. / Dead End)

Stay Wire (7/4.00 mm) (10 kg Per Stay Set)

HT Earthing set complete

Earth wire (GI, 6 SWG) {Includes Single wire length and Additional 3% (Sag, cross lacing and wastage)}@ 150 kg/km

Eye Hook for earth wire

Earth Reel

MS Channel Iron: 75x40x6, Length :3300 mm

Half clamps: [On Double Pole Dead End structure: 6 No, Run Thro' structure: 1 No]

Full clamps: [On Double Pole Dead End structure: 4 No, Run Thro' structure: 3 No]

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 20 mm Φ or more (with flat and spring washers)]

Barbed wire

Danger Plate (203X200X1.6mm)

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

HVDS-New HT Line works as per Scope of Works

New 22kv New Line on Steel Tubular Pole with Rabbit Conductor -50Sq. mm

ACSR 6/1/3.35 (50mm²) {Includes 3 conductor lengths for 3Φ and Inclusive 3% (Sag, Jumpering and wastage}

11M Steel Tublar Pole (11 m, Working Load > 227 kgf/m²) (with Ruling Span 90 m, 8 No. Run thro' and 3 No. Double Pole Dead End Structures)

Muffs with concerete filling

Cross Arm: [Channel Iron (100x50x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators with GI Pin(Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

22 kV Pin Insulators (Porcelain, 24 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (1No. / Single Pole , 4 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 4 No; On Run Thro' structure: 2 No ]

Full clamps: [On Double Pole Dead End structure: 4 No, Single Pole Run Thro' structure: 2 No]

Danger Plate

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

New 22kv New Line on STP with rabbit Conductor -50Sq.mm

ACSR Rabbit 50mm²) {Includes 3 conductor lengths for 3Φ and Additional 1% (Sag, Jumpering and wastage}

Steel Tubular Pole 11 Mtr long

Muffs with concerete filling

X-Arms: [MS Channel Iron (125x65x6 mm, Length: 2000 mm i/c tolerance 100 mm on either side] x 10 No. Structures

Pin Insulator

Knee bracing Set

Belt Set - MS Angle Iron: 65x65x6, Length:(1800 mm) x 2 No.

X-Bracing Set - MS Angle Iron: 50X50x6, Length [2700 mm) x 2 No.]

X-Arm (Horizontal) - MS Channel Iron: (125x65x6 mm), Length: 2600 mm i/c tolerance 100 mm on either side x 2 No.]

Disc insulator String (Strain) sets: 2 No. Discs in each string: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (Single Circuit: 3 No. conductors) x (2 No. sides) /Dead Structures

33 kV Pin Insulators (Porcelain, 36 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (2 No./Run Thro & 5 No. / Dead End)

Stay Wire (7/4.00 mm) (10 kg Per Stay Set)

HT Earthing set complete

Earth wire (GI, 6 SWG) {Includes Single wire length and Additional 3% (Sag, cross lacing and wastage)}@ 150 kg/km

Eye Hook for earth wire

Earth Reel

MS Channel Iron: 75x40x6, Length :3300 mm

Half clamps: [On Double Pole Dead End structure: 6 No, Run Thro' structure: 1 No]

Full clamps: [On Double Pole Dead End structure: 4 No, Run Thro' structure: 3 No]

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 20 mm Φ or more (with flat and spring washers)]

Barbed wire

Danger Plate (203X200X1.6mm)

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

11kv New Line on Steel Tubular Pole with Dog Conductor -100 Sq. mm

ACSR 6/1/4.72 {Includes 3 conductor lengths for 3Φ and Inclusive 3% (Sag, Jumpering and wastage}

11M Steel Tublar Pole (11 m, Working Load > 227 kgf/m²) (with Ruling Span 90 m, 8 No. Run thro' and 3 No. Double Pole Dead End Structures)

Muffs with concerete filling

Cross Arm: [Channel Iron (100x50x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators with GI Pin(Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

11 kV Pin Insulators (Porcelain, 12 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (1No. / Single Pole , 4 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 4 No; On Run Thro' structure: 2 No ]

Full clamps: [On Double Pole Dead End structure: 4 No, Single Pole Run Thro' structure: 2 No]

Danger Plate

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

Supply ,Installation and commissioning of New DT as per scope of work

Distribution Transformer 25 kva , 11/.440v

Distribution Transformer (Ordinary), 11/0.4 kV, 25 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incommer line

MS Angle Iron (50X50x6 mm), Length: 2800 x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : 2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x5 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(50A, 25 kA, 4P),O/G Kit Kit 63A 4Nos

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 50 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 4- KVAr for 25 KVA (rate per KVAr)

Distribution Transformer 63 kva , 11/.440v

Distribution Transformer (Ordinary), 11/0.4 kV, 63 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(63A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 120mm²

Red oxide

Aluminium Paint

LT Switched Capacitors 8- KVAr for 63KVA (rate per KVAr)

Distribution Transformer 100 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 100 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(160A, 25 kA, 4P) and SFU(100A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 185 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 12- KVAr for 100 KVA (rate per KVAr)

Distribution Transformer 10KVA

Distribution Transformer (Ordinary), 22/0.4 kV, 10KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(50A, 25 kA, 4P)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 35 mm²

Red Oxide

Aluminium Paint

Distribution Transformer 16 KVA

Distribution Transformer (Ordinary), 22/0.23 kV, 16 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS,12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(50A, 25 kA, 4P)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 35 mm²

Red Oxide

Aluminium Paint

Distribution Transformer 25 kva , 22/.440v

Distribution Transformer (Ordinary), 22/0.4 kV, 25 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incommer line

MS Angle Iron (50X50x6 mm), Length: 2800 x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : 2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x5 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(50A, 25 kA, 4P),O/G Kit Kit 63A 4Nos

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 50 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 4- KVAr for 25 KVA (rate per KVAr)

Distribution Transformer 63 kva , 22/.440v

Distribution Transformer (Ordinary), 22/0.4 kV, 63 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(63A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 120mm²

Red oxide

Aluminium Paint

LT Switched Capacitors 8- KVAr for 63KVA (rate per KVAr)

Conversion to LT Line to AB Cable

Conversion of bare conductor with 3x70+50 (Insulated) +16 Sq. mm AB cable

LT AB Cable on poles [Size: : 3x70mm²) + 50 sqmm+16sqmm x 1 Cables {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

Anchoring Assembly for LT

Suspension Assembly for LT

Facade Hooks for LT

Distribution box 3 phase 5 connectors as per TS

Piercing Connector as per TS

Cable for SMDB 3.5Core X 35sqmm

T-Jointing kit

LT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Conversion of bare conductor with 3x50 + 35 (Insulated) sqmm +16 Sq. mm (Insulated) AB cable

LT AB Cable on poles [Size: : 3x50mm²) + 35 (Insulated) sqmm+16sqmm x 1 Cables {Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

Anchoring Assembly for LT

Suspension Assembly for LT

Facade Hooks for LT

Distribution box 3 phase 5 connectors as per TS

Piercing Connector as per TS

Cable for SMDB 3.5Core X 35sqmm

T-Jointing kit

LT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Feeder Bifurcation Works

Feeder Bifurcation Works-New HT Lines

New 22kv New Line on Steel Tubular Pole with Dog Conductor -100Sq. mm

ACSR 6/1/4.72 {Includes 3 conductor lengths for 3Φ and Inclusive 3% (Sag, Jumpering and wastage}

11M Steel Tublar Pole (11 m, Working Load > 227 kgf/m²) (with Ruling Span 90 m, 8 No. Run thro' and 3 No. Double Pole Dead End Structures)

Muffs with concerete filling

Cross Arm: [Channel Iron (100x50x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators with GI Pin(Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

22 kV Pin Insulators (Porcelain, 24 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (1No. / Single Pole , 4 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 4 No; On Run Thro' structure: 2 No ]

Full clamps: [On Double Pole Dead End structure: 4 No, Single Pole Run Thro' structure: 2 No]

Danger Plate

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

11kv New Line on STP with rabbit Conductor -50 Sq. mm

ACSR 6/1/3.35 (50mm²) {Includes 3 conductor lengths for 3Φ and Additional 1% (Sag, Jumpering and wastage}

STP 11 Mtr Long

Muffs with concerete filling

Cross Arm: [Channel Iron (125x65x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators (Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 125x65x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

11 kV Pin Insulators (Porcelain, 12 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (2 No./Run Thro & 5 No. / Dead End)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 6 No, Run Thro' structure: 1 No]

Full clamps: [On Double Pole Dead End structure: 4 No, Run Thro' structure: 3 No]

Danger Plate (250X200X1.6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

Fault Path indicator

22kv New Line on STP with Rabbit Conductor -50 Sq. mm

ACSR Dog 50mm²) {Includes 3 conductor lengths for 3Φ and Additional 1% (Sag, Jumpering and wastage}

Muffs with concerete filling

Cross Arm: [Channel Iron (125x65x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

22kV Pin Insulators (Porcelain, 23 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 125x65x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

22 kV Pin Insulators (Porcelain, 12 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (2 No./Run Thro & 5 No. / Dead End)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 6 No, Run Thro' structure: 1 No]

Full clamps: [On Double Pole Dead End structure: 4 No, Run Thro' structure: 3 No]

Danger Plate (250X200X1.6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

11kv New Line on Steel Tubular Pole with Dog Conductor -100 Sq. mm

ACSR 6/1/4.72 {Includes 3 conductor lengths for 3Φ and Inclusive 3% (Sag, Jumpering and wastage}

11M Steel Tublar Pole (11 m, Working Load > 227 kgf/m²) (with Ruling Span 90 m, 8 No. Run thro' and 3 No. Double Pole Dead End Structures)

Muffs with concerete filling

Cross Arm: [Channel Iron (100x50x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators with GI Pin(Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

11 kV Pin Insulators (Porcelain, 12 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (1No. / Single Pole , 4 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 4 No; On Run Thro' structure: 2 No ]

Full clamps: [On Double Pole Dead End structure: 4 No, Single Pole Run Thro' structure: 2 No]

Danger Plate

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

11kv New Line on Steel Tubular Pole with Rabbit Conductor -50Sq. mm

ACSR 6/1/3.35 (50mm²) {Includes 3 conductor lengths for 3Φ and Additional 1% (Sag, Jumpering and wastage}

STP 11 Mtr Long

Muffs with concerete filling

Cross Arm: [Channel Iron (125x65x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators (Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 125x65x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

11 kV Pin Insulators (Porcelain, 12 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (2 No./Run Thro & 5 No. / Dead End)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 6 No, Run Thro' structure: 1 No]

Full clamps: [On Double Pole Dead End structure: 4 No, Run Thro' structure: 3 No]

Danger Plate (250X200X1.6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

Feeder Bifurcation Works-DT

Supply ,Installation and commissioning of New DT as per scope of work

Distribution Transformer 25 kva , 11/.440v

Distribution Transformer (Ordinary), 11/0.4 kV, 25 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incommer line

MS Angle Iron (50X50x6 mm), Length: 2800 x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : 2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x5 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(50A, 25 kA, 4P),O/G Kit Kit 63A 4Nos

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 50 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 4- KVAr for 25 KVA (rate per KVAr)

Distribution Transformer 63 kva , 11/.440v

Distribution Transformer (Ordinary), 11/0.4 kV, 63 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(63A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 120mm²

Red oxide

Aluminium Paint

LT Switched Capacitors - KVAr for 63KVA (rate per KVAr)

Distribution Transformer 100 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 100 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(160A, 25 kA, 4P) and SFU(100A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 185 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 12- KVAr for 100 KVA (rate per KVAr)

Distribution Transformer 250 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 250 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(400A, 50kA, 4P) and SFU(150A, 4No MCCB)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 300 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 36- KVAr for 250 KVA (rate per KVAr)

Distribution Transformer 400 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 400 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS,12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with ACB(630A, 50kA, 4P) and SFU(250A, 4No MCCB)

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 70 mm² X 4 Outgoing

Transformer Bed( Civil Work (As Per HPSR))

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

Red Oxide

Aluminium Paint

LT Switched Capacitors 60- KVAr for 400 KVA (rate per KVAr)

Distribution Transformer 630 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 630 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with ACB(1000A, 50kA, 4P) and SFU(250A, 4No MCCB)

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 95 mm² X 4 Outgoing

Transformer Bed( Civil Work (As Per HPSR))

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

Red Oxide

Aluminium Paint

LT Switched Capacitors 60VAr for 630 KVA (rate per KVAr)

Distribution Transformer 63 kva , 22/.440v

Distribution Transformer (Ordinary), 22/0.4 kV, 63 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(63A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 120mm²

Red oxide

Aluminium Paint

LT Switched Capacitors 8- KVAr for 63KVA (rate per KVAr)

Distribution Transformer 100 KVA

Distribution Transformer (Ordinary), 22/0.4 kV, 100 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS,12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(160A, 25 kA, 4P) and SFU(100A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 185 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 12 KVAr for 100 KVA (rate per KVAr)

Feeder Bifurcation-New LT Lines

LT AB Cable on poles [Size: (3x95 Sq, mm ) +70sqmm (Insulated) +16 sqmm{Inclusive 3% sagging & wastage)

LT AB Cable on poles [Size: (3x95 Sq, mm ) +70sqmm (Insulated) +16 sqmm{Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

Anchoring Assembly for LT

Suspension Assembly for LT

Facade Hooks for LT

Distribution box 3 phase 5 connectors as per TS

Piercing Connector as per TS

Cable for SMDB 3.5Core X 35sqmm

LT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

New LT Line -single phase two wire on rabbit conductor -50 Sq. mm

ACSR 6/1/3.35 (50mm²) inclusive of sag and wastage

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set Complete

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Earth wire (GI, 8 SWG) {Additional 1% (Sag and wastage)} @ 0.102 kg/m

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

New LT Line -Three phase four wire on rabbit conductor -50 Sq. mm

ACSR 6/1/3.35 (50mm²) inclusive of sag and wastage

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Earth wire (GI, 8 SWG) {Additional 1% (Sag and wastage)} @ 0.102 kg/m

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

Spiral PVC Spacer

New HT Line works as per Scope of Works

Feeder Segeration-

Feeder Segeration-New HT Lines

11kv New Line on STP with Dog Conductor -100 Sq. mm

ACSR 6/1/3.35 (50mm²) {Includes 3 conductor lengths for 3Φ and Additional 1% (Sag, Jumpering and wastage}

Muffs with concerete filling

Cross Arm: [Channel Iron (125x65x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators (Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 125x65x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

11 kV Pin Insulators (Porcelain, 12 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (2 No./Run Thro & 5 No. / Dead End)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 6 No, Run Thro' structure: 1 No]

Full clamps: [On Double Pole Dead End structure: 4 No, Run Thro' structure: 3 No]

Danger Plate (250X200X1.6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

Feeder Segeration Works-DT

Supply ,Installation and commissioning of New DT as per scope of work

Distribution Transformer 63 kva , 11/.440v

Distribution Transformer (Ordinary), 11/0.4 kV, 63 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(63A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 120mm²

Red oxide

Aluminium Paint

LT Switched Capacitors 8- KVAr for 63KVA (rate per KVAr)

Distribution Transformer 100 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 100 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(160A, 25 kA, 4P) and SFU(100A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 185 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 12- KVAr for 100 KVA (rate per KVAr)

Feeder Segeration-New LT Lines

LT AB Cable on poles [Size: (3x95 Sq, mm ) +70sqmm (Insulated)+16 sqmm{Inclusive 3% sagging & wastage)

LT AB Cable on poles [Size: (3x95 Sq, mm ) +70sqmm (Insulated) +16 sqmm{Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

Anchoring Assembly for LT

Suspension Assembly for LT

Facade Hooks for LT

Distribution box 3 phase 5 connectors as per TS

Piercing Connector as per TS

Cable for SMDB 3.5Core X 35sqmm

LT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

NEW HT Lines

New 22kv New Line on Steel Tubular Pole with Dog Conductor -100Sq. mm

ACSR 6/1/4.72 {Includes 3 conductor lengths for 3Φ and Inclusive 3% (Sag, Jumpering and wastage}

11M Steel Tublar Pole (11 m, Working Load > 227 kgf/m²) (with Ruling Span 90 m, 8 No. Run thro' and 3 No. Double Pole Dead End Structures)

Muffs with concerete filling

Cross Arm: [Channel Iron (100x50x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators with GI Pin(Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

22 kV Pin Insulators (Porcelain, 24 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (1No. / Single Pole , 4 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 4 No; On Run Thro' structure: 2 No ]

Full clamps: [On Double Pole Dead End structure: 4 No, Single Pole Run Thro' structure: 2 No]

Danger Plate

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

11kv New Line on Steel Tubular Pole with Rabbit Conductor -50Sq. mm

ACSR 6/1/3.35 (50mm²) {Includes 3 conductor lengths for 3Φ and Inclusive 3% (Sag, Jumpering and wastage}

11M Steel Tublar Pole (11 m, Working Load > 227 kgf/m²) (with Ruling Span 90 m, 8 No. Run thro' and 3 No. Double Pole Dead End Structures)

Muffs with concerete filling

Cross Arm: [Channel Iron (100x50x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators with GI Pin(Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

11 kV Pin Insulators (Porcelain, 12 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (1No. / Single Pole , 4 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 4 No; On Run Thro' structure: 2 No ]

Full clamps: [On Double Pole Dead End structure: 4 No, Single Pole Run Thro' structure: 2 No]

Danger Plate

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

NEW LT Lines (on New Dts)

New LT Line -single phase two wire on rabbit conductor -50 Sq. mm

ACSR 6/1/3.35 (50mm²) inclusive of sag and wastage

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set Complete

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Earth wire (GI, 8 SWG) {Additional 1% (Sag and wastage)} @ 0.102 kg/m

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

New LT Line -Three phase four wire on rabbit conductor -50 Sq. mm

ACSR 6/1/3.35 (50mm²) inclusive of sag and wastage

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Earth wire (GI, 8 SWG) {Additional 1% (Sag and wastage)} @ 0.102 kg/m

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

Spiral PVC Spacer

New LT Line -Three phase four wire on Dog conductor -100 Sq. mm

ACSR 6/1/4.72 {Includes 4 conductor lengths for 3Φ, 4 wire and Inclusive 3% (Sag, Jumpering and wastage}

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Earth wire (GI, 8 SWG) {Additional 1% (Sag and wastage)} @ 0.102 kg/m

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

Spiral PVC Spacer

New DT

Supply ,Installation and commissioning of New DT as per scope of work

Distribution Transformer 25 kva , 11/.440v

Distribution Transformer (Ordinary), 11/0.4 kV, 25 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incommer line

MS Angle Iron (50X50x6 mm), Length: 2800 x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : 2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x5 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(50A, 25 kA, 4P),O/G Kit Kit 63A 4Nos

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 50 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 4- KVAr for 25 KVA (rate per KVAr)

Distribution Transformer 63 kva , 11/.440v

Distribution Transformer (Ordinary), 11/0.4 kV, 63 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(63A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 120mm²

Red oxide

Aluminium Paint

LT Switched Capacitors 8- KVAr for 63KVA (rate per KVAr)

Distribution Transformer 100 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 100 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(160A, 25 kA, 4P) and SFU(100A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 185 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 12- KVAr for 100 KVA (rate per KVAr)

Distribution Transformer 250 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 250 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(400A, 50kA, 4P) and SFU(150A, 4No MCCB)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 300 mm²

Transformer Bed( Civil Work (As Per HPSR))

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Red Oxide

Aluminium Paint

LT Switched Capacitors 36- KVAr for 250 KVA (rate per KVAr)

Distribution Transformer 400 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 400 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with ACB(630A, 50kA, 4P) and SFU(250A, 4No MCCB)

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 70 mm² X 4 Outgoing

Transformer Bed( Civil Work (As Per HPSR))

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

Red Oxide

Aluminium Paint

LT Switched Capacitors 60- KVAr for 400 KVA (rate per KVAr)

Distribution Transformer 630 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 630 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (11kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 11KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with ACB(1000A, 50kA, 4P) and SFU(250A, 4No MCCB)

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 95 mm² X 4 Outgoing

Transformer Bed( Civil Work (As Per HPSR))

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

Red Oxide

Aluminium Paint

LT Switched Capacitors 60KVAr for 630 KVA (rate per KVAr)

Distribution Transformer 25 kva , 22/.440v

Distribution Transformer (Ordinary), 22/0.4 kV, 25 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incommer line

MS Angle Iron (50X50x6 mm), Length: 2800 x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : 2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x5 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(50A, 25 kA, 4P),O/G Kit Kit 63A 4Nos

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 50 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 4- KVAr for 25 KVA (rate per KVAr)

Distribution Transformer 63 kva , 22/.440v

Distribution Transformer (Ordinary), 22/0.4 kV, 63 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete (HT)

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(63A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 120mm²

Red oxide

Aluminium Paint

LT Switched Capacitors 8- KVAr for 63KVA (rate per KVAr)

Distribution Transformer 100 KVA

Distribution Transformer (Ordinary), 22/0.4 kV, 100 KVA

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(200A, 25 kA, 4P) and SFU(100A, 4No, rewirable)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 185 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 12- KVAr for 100 KVA (rate per KVAr)

Distribution Transformer 250 KVA

Distribution Transformer (Ordinary), 22/0.4 kV, 250 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with MCCB(400A, 50kA, 4P) and SFU(150A, 4No MCCB)

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

LT Cable (3.5 Core) 300 mm²

Transformer Bed( Civil Work (As Per HPSR))

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Red Oxide

Aluminium Paint

LT Switched Capacitors 36- KVAr for 250 KVA (rate per KVAr)

Distribution Transformer 400 KVA

Distribution Transformer (Ordinary), 22/0.4 kV, 400 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with ACB(630A, 50kA, 4P) and SFU(250A, 4No MCCB)

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 70 mm² X 4 Outgoing

Transformer Bed( Civil Work (As Per HPSR))

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

Red Oxide

Aluminium Paint

LT Switched Capacitors 60- KVAr for 400 KVA (rate per KVAr)

Distribution Transformer 630 KVA

Distribution Transformer (Ordinary), 22/0.4 kV, 630 KVA

Steel Tubular Poles (10 m, Working Load > 300 kgf/m²)

Muffs with concerete filling

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for incomer line

MS Angle Iron (50X50x6 mm), Length: (2800 mm) x1 Nos for LA's

X-Arm: [Channel Iron (75x40x6 mm), Length : (2800 mm X 4 Nos] for supporting DO fuse unit & GO switch

X-Arm: [Channel Iron (100x50x6 mm), Length : 2800 mm X 2 Nos] for Transformer Bed

X-Arm [Channel Iron (100x50x6 mm), Length : (460 mm) x 2 Nos for supporting Main Channel of Transformer]

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (35X35x5 mm), Length : (460 ) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (950 mm) x 2 Nos for Bed Knee Bracing

MS Angle Iron (50X50x6 mm), Length : (2800 mm) x 2 Nos

MS Angle Iron (50X50x6 mm), Length : (450 mm) x 1 Nos

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

D.O Fuse Unit 22KV

Lightening Arrester, 9 kV Station Class (Porcelain Type)

Discs insulator sets (comprising 2 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.)

Stay set complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Substation Pipe Earthing Complete Set(REC Constr. Stand. J-1) Inclusive MS Flat 50x6

LT Distribution Panel Box with ACB(1000A, 50kA, 4P) and SFU(250A, 4No MCCB)

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 95 mm² X 4 Outgoing

Transformer Bed( Civil Work (As Per HPSR))

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Half Clamp (M.S. Flat 50X6 mm)

Full Clamps (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

Barbed Wire

Red Oxide

Aluminium Paint

LT Switched Capacitors 60KVAr for 630 KVA (rate per KVAr)

Augmentation of DT as per given Scope of work

Augmentation of DT 25 KVA to 63 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 63 KVA

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(32A, 4No, rewirable)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

LT Cable (3.5 Core) 120mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors8- KVAr for 63 KVA (rate per KVAr)

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 25 KVA to 100 KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 100 KVA

LT Distribution Panel Box with MCCB(160A, 25 kA, 4P) and SFU(16A, 4No, rewirable)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

LT Cable (3.5 Core) 185mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 12- KVAr for 100 KVA (rate per KVAr)

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 63 KVA to 100KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 100 KVA

LT Distribution Panel Box with MCCB(160A, 25 kA, 4P) and SFU(16A, 4No, rewirable)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

LT Cable (3.5 Core) 185 mm²

Red oxide

Aluminium Paint

LT Switched Capacitors 12- KVAr for 100KVA (rate per KVAr)

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 100 KVA to 250KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 250 KVA

LT Distribution Panel Box with ACB(400A, 50 kA, 4P,1 No) and SFU(150A, 4No MCCB)

Half Clamp (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

LT Cable (3.5 Core) 300 mm²

LT Switched Capacitors 36- KVAr for 250KVA (rate per KVAr)

Civil Work Bed for 250 KVA DT (As PER HPSR)

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 250 KVA to 400KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 400 KVA

LT Distribution Panel Box with ACB(630AI/C, 50 kA, 4P, & o/G 4 Nos MCCB 200A

Half Clamp (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 70 mm² X 4 Outgoing

LT Switched Capacitors 60 KVAr for 400KVA (rate per KVAr)

Civil Work Bed for 400 KVA DT (As PER HPSR)

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 250 KVA to 630KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 630 KVA

LT Distribution Panel Box with ACB(I/C 1000A, 50 kA, 4P,&5 Nos O/G MCCB 200 A

Half Clamp (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 95 mm² X 4 Outgoing

LT Switched Capacitors 60KVAr for 630KVA (rate per KVAr)

Civil Work Bed for 400 KVA DT (As PER HPSR)

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 630 KVA to 1000KVA

Distribution Transformer (Ordinary), 11/0.4 kV, 1000 KVA

LT Distribution Panel Box with ACB(I/C 1600A, 50 kA, 4P,&5 Nos O/G MCCB 200 A

Half Clamp (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

LT Cable (3.5 Core) 500 mm² X 2 incommer

LT Cable (3.5 Core) 185 mm² X 4 Outgoing

LT Switched Capacitors 60 KVAr for 1000KVA (rate per KVAr)

Civil Work Bed for 400 KVA DT (As PER HPSR)

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 400KVA to 630KVA

630 KVA,11/0.4KV DISTRIBUTION TRANSFORMER,

Transformer Bed( Civil Work (As Per HPSR))

LT Distribution Panel Box with ACB(1000A, 50 kA, 4P and SFU 4Nos MCCB 250A

M.S. NUTS &BOLTS OFF SIZES

Aluminium Thimble

Aluminium Thimble

LT Cable (3.5 Core) 400 mm² x 2 incoming

LT Cable (3.5 Core) 95 mm² x 4outgoing feeder

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Red Oxide

Aluminium paint

LT Switched Capacitors 60 KVAr for 630KVA (rate per KVAr)

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 25 KVA to 63 KVA on 22kv line

Distribution Transformer (Ordinary), 22/0.4 kV, 63 KVA

LT Distribution Panel Box with MCCB(100A, 25 kA, 4P) and SFU(32A, 4No, rewirable)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

LT Cable (3.5 Core) 120mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 8- KVAr for 63 KVA (rate per KVAr)

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 63 KVA to 100KVA on 22kv line

Distribution Transformer (Ordinary), 22/0.4 kV, 100 KVA

LT Distribution Panel Box with MCCB(160A, 25 kA, 4P) and SFU(16A, 4No, rewirable)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

Danger Plate

LT Cable (3.5 Core) 185 mm²

Red Oxide

Aluminium Paint

LT Switched Capacitors 12- KVAr for 100KVA (rate per KVAr)

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 100 KVA to 250KVA on 22kv line

Distribution Transformer (Ordinary), 22/0.4 kV, 250 KVA

LT Distribution Panel Box with MCCB(400A, 50kA, 4P) and SFU(150A, 4No MCCB)

Half Clamp (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

LT Cable (3.5 Core) 300 mm²

Civil Work Bed for 250 KVA DT (As PER HPSR)

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

LT Switched Capacitors 36 KVAr for 250KVA (rate per KVAr)

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 250 KVA to 400KVA on 22kv line

Distribution Transformer (Ordinary), 22/0.4 kV, 400 KVA

LT Distribution Panel Box with ACB(630A, 50kA, 4P) and SFU(250A, 4No MCCB)

Half Clamp (M.S. Flat 50X6 mm)

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Thimble

Aluminium Thimble

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 70 mm² X 6 Outgoing

Civil Work Bed for 400 KVA DT (As PER HPSR)

Chain link welded fencing , Angle Iron ,Gate etc for transformer fencing

Capacitor Bank of 60VR for 400kVA,

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of DT 400KVA to 630KVA

630 KVA,11/0.4KV DISTRIBUTION TRANSFORMER,

Transformer Bed( Civil Work (As Per HPSR))

LT Distribution Panel Box with ACB(1000A, 50kA, 4P) and SFU(250A, 4No MCCB)

M.S. NUTS &BOLTS OFF SIZES

Aluminium Thimble

Aluminium Thimble

LT Cable (3.5 Core) 400 mm² X 2 incommer

LT Cable (3.5 Core) 95 mm² X 4 Outgoing

Chain Link fencing , Angle Iron ,Gate etc for transformer fencing

Red Oxide

Aluminium paint

LT Switched Capacitors 60KVAr for 630KVA (rate per KVAr)

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of LT Line

Augmentation of LT Lines -1 phase to 3-phase with 50 Sq. mm Rabbit conductor

ACSR Rabbit Conductor 50 Sq. mm inclusive of sag and wastage

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

Spiral PVC Spacer

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of LT Lines -2 phase to three phase with 50 Sq. mm Rabbit conductor

ACSR Rabbit Conductor 50 Sq. mm inclusive of sag and wastage

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

Spiral PVC Spacer

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augmentation of LT Lines -1 phase to three phase with 100 Sq. mm Dog conductor

ACSR Dog Conductor 100 Sq. mm inclusive of sag and wastage

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

Spiral PVC Spacer

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Augumentation of LT Line with LT AB Cable on poles [Size: (3x120 Sq, mm ) +70sqmm +16 sqmm{Inclusive 3% sagging & wastage)

LT AB Cable on poles [Size: (3x120 Sq, mm ) +70sqmm +16 sqmm{Inclusive 3% sagging & wastage)

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Stay Set Complete

Stay Wire (7/3.15 mm) (7.0 kg Per Stay Set)

Full Clamp for stay

Anchoring Assembly for LT

Suspension Assembly for LT

Facade Hooks for LT

Distribution box 3 phase 5 connectors as per TS

Piercing Connector as per TS

Cable for SMDB 3.5Core X 35sqmm

LT Earthing set complete (preferbly coil earthing)

Red Oxide

Aluminium paint

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

Reconductoring of LT Lines -3 phase4Wire with 100 Sq. mm Dog conductor

ACSR 6/1/4.72(100mm²) inclusive of sag and wastage

Steel Tubular Poles (9 m, Working Load > 200 kgf/m²)

Muffs with concerete filling

Angle Iron (75x75x6) [Length- 1.50 Mtr + 0.02 Mtr]

Shackle Insulator (16 kN)

D-Iron (U- Clamps)

Earth Knob

LT Stay Set

Stay Wire (7/3.15 mm) (6.0 kg Per Stay Set)

Full Clamps [ 2 No for A.I + 1 No for Stay Set]

Earthing Set complete

Earth wire (GI, 8 SWG) {Additional 1% (Sag and wastage)} @ 0.102 kg/m

Spool Tie

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Aluminium Paint

Red Oxide

Spiral PVC Spacer

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

New 11 kv line

11kv New Line on Steel Tubular Pole with Dog Conductor -100 Sq. mm

ACSR 6/1/4.72 {Includes 3 conductor lengths for 3Φ and Inclusive 3% (Sag, Jumpering and wastage}

11M Steel Tublar Pole (11 m, Working Load > 227 kgf/m²) (with Ruling Span 90 m, 8 No. Run thro' and 3 No. Double Pole Dead End Structures)

Muffs with concerete filling

Cross Arm: [Channel Iron (100x50x6 mm), Length: 1270 mm i/c tolerance of 100 mm either side) x 8 structure

Angle Iron (50x50x6 mm), Length: 750 mm x 2 No. x 8 structures

Pole Top Bracket [MSCI:100x50x6 mm- 100 mm]

11 kV Pin Insulators with GI Pin(Porcelain, 12 kV, 10 KN): 3 No per pole structure

Belt Set - MS Angle Iron: 50x50x6, Length :1800 mm x 2 No.

X-Bracing Set - MS Angle Iron: 50x50x6, Length: 2125 mm x 2 No.

X-Arm (Horizontal) - MS Channel Iron: 100X50x6, Length: 2340 mm x 2 No.] ∆ Formation

Discs insulator sets on Dead End structures (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors) x (2 No. sides)

11 kV Pin Insulators (Porcelain, 12 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (1No. / Single Pole , 4 No. / Double Pole Structures)

Stay Wire (7/3.15 mm) (10.0 kg Per Stay Set)

HT Earthing set complete (REC Constr. Stand. J-1)

Single Continous Earth wire (GI, 8 SWG) {alongwith 2 wire lengths for avg. one road crossing @ 20 m and Additional 1% (Sag and wastage)} @ 0.102 kg/m

Cross Lacings (GI, 8 SWG) [ 2.2 m x 9 Nos @ 2 m spacing] {0.102 kg/m}

Eye Hook for earth wire

Earth Wire Clamp

MS Channel Iron: 75x40x6, Length : 2400 mm for Road crossing

Half clamps: [On Double Pole Dead End structure: 4 No; On Run Thro' structure: 2 No ]

Full clamps: [On Double Pole Dead End structure: 4 No, Single Pole Run Thro' structure: 2 No]

Danger Plate

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

Barbed Wire

Red Oxide

Aluminium Paint

GO Switch Handle Supporting: [Channel Iron (75x40x6 mm), Length : 460 mm

GO AB Switch Unit (22kV, 400A, 25 KA ) Tripple pole O/D type

Augumentation of 33 kv line

Augumentation of 33KV Wolf Conductor of 150sqmm

ACSR (150mm²) {Includes 3 conductor lengths for 3Φ and Additional 1% (Sag, Jumpering and wastage}

Steel Tubular Poles (11 m, Working Load > 227 kg) (with Ruling Span 90 m, 10 No. Run thro' and 3 No. Dead End Structures)

Muffs (2000mm) with concerete filling

X-Arms: [MS Channel Iron C type (125X66X6) mm, Length: 3250 mm i/c tolerance 100 mm on either side] x 10 No. Structures

Disc insulator String (Suspension) sets: 3 No. Discs in each string: ^^(Porcelain, CT, 12 kV, 90 kN) including dead end clamps etc)x (Single circuit : 3No conductors) x 1 No sides) /Run Throu' structures.

Belt Set - MS Angle Iron: 65x65x6, Length:(1800 mm) x 2 No.

X-Bracing Set - MS Angle Iron: 50X50x6, Length [2700 mm) x 2 No.]

Belt Set - MS Angle Iron: 65x65x6, Length:(1800 mm) x 2 No.

X-Bracing Set - MS Angle Iron: 50X50x6, Length [2700 mm) x 2 No.]

X-Arm (Horizontal) - MS Channel Iron C type: (125x66x6 mm), Length: 3250 mm i/c tolerance 100 mm on either side x 2 No.]

Discs insulator String sets on Dead End structures (comprising 3 No. Discs in each string: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps, Bend Stapples & straight Stapples etc.) x (3 No. conductors) x (2 No. sides)

33 kV Pin Insulators (Porcelain, 36 kV, 10 kN): 3 No per double pole structure

Dead End Clamp L/S

PG Clamp L/S

Stay set complete in all respect (2 No./Run Thro & 8 No. / Dead End)

Stay Wire (7/4.00 mm) (9.0 kg Per Stay Set)

HT Earthing set complete

Eye Hook for earth wire

Earth Reel

Half clamps: [On Double Pole Dead End structure: 6 No, Double Pole Run Thro' structure: 8 No]

Full clamps: [On Double Pole Dead End structure: 4 No, Double Pole Run Thro' structure: 4 No]

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 20 mm Φ or more (with flat and spring washers)]

Barbed wire

Danger Plate (203X200X1.6mm)

Red Oxide

Aluminium Paint

Cost is inclusive of dismantling of existing infra and depositing all Dismantalled Material back to Concerned Store as per direction of Engineer In Charge

New 33 KV Line Work

New 33 KV Single Circuit Line with Dog Conductor on STP

ACSR 6/1/4.72 (100mm²) {Includes 3 conductor lengths for 3Φ and Additional 1% (Sag, Jumpering and wastage}

New 33 KV Single Circuit Line with Dog Conductor on 11 mtr STP

Muffs with concerete filling

X-Arms: [MS Channel Iron (100x50x6 mm, Length: 3250 mm i/c tolerance 100 mm on either side] x 10 No. Structures

Disc insulator String (Suspension) sets: 3 No. Discs in each string: ^^(Porcelain, CT, 12 kV, 90 kN) including dead end clamps etc)x (Single circuit : 3No conductors) x 1 No sides) /Run Throu' structures.

Belt Set - MS Angle Iron: 65x65x6, Length:(1800 mm) x 2 No.

X-Bracing Set - MS Angle Iron: 50X50x6, Length [2700 mm) x 2 No.]

Belt Set - MS Angle Iron: 65x65x6, Length:(1800 mm) x 2 No.

X-Bracing Set - MS Angle Iron: 50X50x6, Length [2700 mm) x 2 No.]

X-Arm (Horizontal) - MS Channel Iron: (100x50x6 mm), Length: 3250 mm i/c tolerance 100 mm on either side x 2 No.]

Disc insulator String (Strain) sets: 3 No. Discs in each string: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (Single Circuit: 3 No. conductors) x (2 No. sides) /Dead Structures

33 kV Pin Insulators (Porcelain, 36 kV, 10 kN): 3 No per double pole structure

Stay set complete in all respect (2 No./Run Thro & 4 No. / Dead End)

Stay Wire (7/4.00 mm) (10 kg Per Stay Set)

HT Earthing set complete

Earth wire (GI, 6 SWG) {Includes Single wire length and Additional 1% (Sag and wastage)}@ 150 kg/km

Eye Hook for earth wire

Earth Reel

MS Channel Iron: 75x40x6, Length :3300 mm

Half clamps: [On Double Pole Dead End structure: 6 No, Double Pole Run Thro' structure: 8 No]

Full clamps: [On Double Pole Dead End structure: 4 No, Double Pole Run Thro' structure: 4 No]

Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 20 mm Φ or more (with flat and spring washers)]

Barbed wire

Danger Plate (203X200X1.6mm)

Red Oxide

Aluminium Paint

New 33/11 KV Sub Station

2X10MVA (NEW PSS)(At -Kirpalpur,Tehliwal For Solan circle,Moginand,Kheri for Nahan Circle) Total = 4 Nos.

Power Transformer (10 MVA, 33/11 kV, ONAN, OLTC, Outdoor)

Sub Station Transformer (100 kVA, 33/0.4 kV)

33 kV Switchgear & Allied Equipment:

a) 33 kV Control and Relay (CR) Panel (with Numeric Differential Relay, IEC 61850)

b) 33 kV Control and Relay (CR) Panel (33 kV Incomer Bus) [Numeric Relay, IEC 61850]

c) 33 kV VCB (36 kV, 1250A, 26.2 kA, Outdoor Type)

d) 33 kV Isolator (1600 A, 25kA, with Earth Switch) (Moterised)

e) 33 kV Isolator (1600 A, 25kA, without Earth Switch) (Moterised)

f) 33 kV LA /Surge Arrester (30 kV, 10KA, Station class, ZnO, Porcelain)

g) 33 kV Current Transformer (33 kV, 1Φ, Multi Ratio Multi Core, Outdoor) (1 No. per Φ)

h) 33 kV Potential Transformer (33 kV/110 V, 1Φ, Multi-Core, Outdoor), (1No. per Φ)

i) 33 kV Drop Out Fuse Unit (33 kV, Expulsion)

11 kV Switchgear and Allied equipment: 02 No. incomer Bus

a) 11 kV incomer Bus: Control and Relay (CR) Panel with VCB (12 kV, 1250 A, 25KA) [Numeric Relay, IEC 61850]

b) 11 kV Incomer Bus: Potential Transformer (11 kV/110V, 3Φ, Indoor)

c) 11 kV LA/ Surge Arrester (9 KV, 10 kA ,Station Class, ZnO, Porcelain, Outdoor)

d) 11 kV Cable (11 kV, 630 mm², XLPE, single Core, Armoured) {Transformer to 11 kV Bus} {50m}+Spare

e) 11 kV Cable Termination Kit (630 mm², Outdoor)

f) 11 kV Cable Termination Kit (630 mm², Indoor)

11 kV Switchgear and Allied equipment: Single (8 No.) Outgoing Feeder

a) 11 kV Outgoing Feeder: Control and Relay (CR) Panel with indoor VCB (12 kV, 1250 A, 25KA) including CT

c) 11 kV LA/ Surge Arrester (9 kV, 10 kA Station Class, ZnO, Porcelain, Outdoor)

d) 11 kV Cable (11 kV, 185 mm², XLPE, Three Core, Armoured) {Busbar VCB to Isolator} {50m+ Spare- 50m}

e) 11 kV Cable Termination Kit (185 mm², Outdoor)

f) 11 kV Cable Termination Kit (185 mm², Indoor)

LT Cable (1.1 kV, 3.5 Core, 70 mm2) {from Station Tfr}

Capacitor Bank (3-Ф, 50 Hz, 1800 KVAr) [ IS:2834 ]

Automatic Capacitor Switch (12 kV, 1250 A, 25 kA) [REC Spec. 20/1981]

Battery Bank with Battery Charger (15 No x 2V Cell, Lead Acid, 30 V, 200 AH)

Distribution Panel (30V, DC)

Distribution Panel (415 V, AC)Distribution Panel (415 V, AC) 200 Amp as incomer MCCB & 6 Nos 63 Amp MCCB as outgoing with voltmeter and Ammeter of 0.5 accuracy class alongwith phase indicating lamps of accuracy class 0.5

Super Strcture and Bus Bar Arrangement

(i) R.S. Joists, size 12800x250x125 mm 16 supports

(ii) R.S.Joists, size 4200x250x125 mm supports for Power Transformer's LA, Station Transformer LA, I/C, Power Transformer's CTs

(iii) M.S. channel iron 125x65 mm, X-arm @13.1 kg/m at 5% wastage for Bus-bar,Isolators,CT, LA's transformer etc.

(iv) M.S. angle iron 65x65 X-arm @ 5.8 kg/m & 5% wastage for body supports belt of Station transformer including 5% wastage

(v) Nuts & Bolts with Washers off sizes

BUS-BAR

(i) 3 Disc insulators Tension String complete with fitting

(ii) ACSR conductor 200 mm² at 10 % wastage

For jumpers at 2 m average 30 nos I.e.

(iii) Tee connections

(iv) PG clamps

Gantry FOR 33 kV

(a) Steel tubular pole 11 m long

(b) RCC muffs (2000mm) & concreting thereof for 1 No. out going Feeder

(a)5.5 m long M.S. channel iron 100X50X5 mm 9.56 kg/m Cross arms for Sub-Station With 1 No. out going Feeder (33kV)

(b) M.S. angle iron 50X50X6 mm 4.5 kg/m Cross arms for Sub-Station With 1 No. out going Feeder [ 4.2x3+5.33x2] (11kV)

(d) M.S. Half clamps

(e) Full Clamp

(f) Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

ACSR 100 mm² conductor for Jumpers [approx. 4 mtr/ phase]

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors)

Clamps for 1 Nos. out going Feeder

33 kV Isolator Moterised with ES

Gantry for 8 no. outgoing feeder

(a) Steel tubular pole 11 m long for 8 No. out going Feeder

(b) RCC muffs (2000mm) & concreting thereof for 1 No. out going Feeder

(a)4.2 m long M.S. channel iron 100X50X5 mm 9.56 kg/m Cross arms for Sub-Station With 1 No. out going Feeder (11Kv)

(b) M.S. angle iron 50X50X6 mm 4.5 kg/m Cross arms for Sub-Station With 1 No. out going Feeder [ 4.2x3+5.33x2] (11kV)

(d) M.S. Half clamps

(e) Full Clamp

(f) Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

ACSR 100 mm² conductor for Jumpers [approx. 4 mtr/ phase]

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors)

Clamps for out going Feeder

11 kV Isolator

Earthing of 33/11KV Substation Total 4 PSS

Earthing of 33 kV yard & equipment & 22 kV or 11kV panels M.S. flat 50x6 mm,wt. 2.4 kg/m At 5% wastage:- (a) Transformer Earthing at 3 points for 2 Nos Power Transformers (body & neutral) at 10 Mtr each 2X(3x10)x1.05=63 Mtr (b) For 4 No. LA's at 4.2 Mtr each 2X4.2x2x1.05=17.64 Mtr (c) For 22 nos. 33 kV super structure at 11.50 Mtr each 22x11.50x1.05 =265.65 Mtr i.e. 266 Mtr (d) For 32 Nos. VCB & CT body earthing at 10 m Each (32x10)x1.05 = 336 Mtr Total =682 mtr. i.e. 682X 2.4= 1638 ie 1.638 MT

GI Wire 6 No. SWG for screening etc.

Eye Block for screening

Tumbuckle for screening

GI Pipe 50 mm dia with holes of 16mm dia at 150 mm for centre to centre for 2 m distance from bottom For Transformer and for 11KV panels and fencing and Fixing of GI pipe 50mm with earth pit 10 nos per PSS Providing Coal=125 kg,Charcoal 23 kg ,Salt 122 kg,Sand 84 kg in each Earth Pit(Earth Pit Material)

MS plates 150x150x6mm for two connection

50x6 mm MS Flat connection with the mat to mat

Nut and bolts galvanized various sizes

Chequered plate cover 500x500x6mm i.e.11.8Kg

Providing MS Rod 40 mm dia 6 mtr long for Earth Matt Rods )(weight 9.9 kg per mtr) 16x6x9.9=950kg and Digging of 6 meter pits for earth rods 40 mm dia

Yard Lighting:-a) 9 m, Steel Tubular poles for yard lighting

b)18 W LED Lamp complete with fittings

c)Post Erection for gate

d)Clamps for GI pipe bracket

e)Underground cable 16 mm² for yard lighting

f)PVC cable size 6 mm² for connecting LED lamp supply

g)Junction box i/c MCCB and other allied

Lighting Emergency (3 No LED Bulbs with holders / wire)

control cable: 2x2.5 mm²

control cable: 4x2.5 mm²

control cable:12x2.5 mm²

3.5 core 95 mm² aluminium cable suitable for 415 V, AC

Fire Fighting Equipments as per TS

Safety Equipments & T & P as per TS

CIVIL WORKS

Control Room one Storey Building Sizes(14.7x14.8)sqm as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33202/2018

water supply and sanitary installation for Control Room Building.

Electrical Installation for control room building (for 60 points)

Septic Tank (1 Nos) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33254/2020

Rain Water Harvesting Tank (1 No per PSS) as per drawing of HPSEBL/SE(D)/ESHPSEBL/HAMIRPUR/33249/2020

Power Transformers Foundation suitable for upto 10 MVA (2 Nos) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33239/2020

Substation Transformer Foundation (1 No)

VCB Foundation (5 Nos) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33241/2020

Foundation of R.S. Joist supports (16 Nos) as per drawing of HPSEBL/SE(D)//ESHPSEBL/HAMIRPUR/33243/2020

Foundation of CT, PT & LA (14Nos) as per drawing of HPSEBL/SE(D)//ESHPSEBL/HAMIRPUR/33242/2020

Outdoor Cable Trench ( 80 mtr Per PSS) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33245/2020

Indoor Cable Trench ( 30 mtr trench per PSS) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33247-48/2020

Cost Of Boundary Wall (200Meter/Pss) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33251-52/2020

Main Gate & Sub-Station Yard Gate(1 Nos) as per drawing of HPSEBL/SE(D)/ESHPSEBL/HAMIRPUR/33253/2020

Spreading of gravells/ Shingles in yard (30CUM ) as per drawing of HPSEBL/SEDES/SSD-478/2021-22-7972-79/2021

Formation of drainage system around the substation around 60x40mtr yard (200 Meter) as per drawing of

Chain Link Fencing with wooven mesh of GI wire 15MX30M

Firewall Protection as per drawing HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33244/2020

Cost of Soil Testing & Contour plans & design

Site Development at Kheri under ED Nahan.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. CODE-2.6.1 (Cutting work)

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.CODE-2.7.1

Centering and shuttering including strutting, propping etc. and removal of form work for : Foundations, footings, bases for columns Code-4.3.1

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:3:6 (1 Cement : 3 coarse sand): 6 graded stone aggregate 40 mm nominal size) CODE: 4.1.6

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size) CODE: 4.1.8

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75mm dia

Site Development at Moginand under ED Nahan.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:1:3:6 (1 cement : 3 coarse sand) : 6 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc.and removal of form for :Retaining walls, return walls, Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. In retaining wall :1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75 mm dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

New 33/11 KV Sub Station

2X6.3 MVA (New Substation)(Shamti at Solan) Total = 1 Nos.

Power Transformer (6.3 MVA, 33/11 kV, ONAN, OLTC, Outdoor)

Sub Station Transformer (100 kVA, 33/0.4 kV)

33 kV Switchgear & Allied Equipment

a) 33 kV Control and Relay (CR) Panel (with Numeric Differential Relay, IEC 61850)

b) 33 kV Control and Relay (CR) Panel (33 kV Incomer Bus) [Numeric Relay, IEC 61850]

c) 33 kV VCB (36 kV, 1250A, 26.2 kA, Outdoor Type)

d) 33 kV Isolator (1600 A, 25kA, with Earth Switch) (Moterised)

e) 33 kV Isolator (1600 A, 25kA, without Earth Switch)(Moterised)

f) 33 kV LA /Surge Arrester (30 kV, 10KA, Station class, ZnO, Porcelain)

g) 33 kV Current Transformer (33 kV, 1Φ, Multi Ratio Multi Core, Outdoor) (1 No. per Φ)

h) 33 kV Potential Transformer (33 kV/110 V, 1Φ, Multi-Core, Outdoor), (1No. per Φ)

i) 33 kV Drop Out Fuse Unit (33 kV, Expulsion)

11 kV Switchgear and Allied equipment: 02 No. incomer Bus

a) 11 kV incomer Bus: Control and Relay (CR) Panel with VCB (12 kV, 1250 A, 25KA) [Numeric Relay, IEC 61850]

b) 11 kV Incomer Bus: Potential Transformer (11 kV/110V, 3Φ, Indoor)

c) 11 kV LA/ Surge Arrester (9 KV, 10 kA ,Station Class, ZnO, Porcelain, Outdoor)

d) 11 kV Cable (11 kV, 400 mm², XLPE, Three Core, Armoured) {Transformer to 11 kV Bus} {50m}+Spare

e) 11 kV Cable Termination Kit (400 mm², Outdoor)

f) 11 kV Cable Termination Kit (400 mm², Indoor)

11 kV Switchgear and Allied equipment: Single (8 No.) Outgoing Feeder

a) 11 kV Outgoing Feeder: Control and Relay (CR) Panel with indoor VCB (12 kV, 1250 A, 25KA) including CT

c) 11 kV LA/ Surge Arrester (9 kV, 10 kA Station Class, ZnO, Porcelain, Outdoor)

d) 11 kV Cable (11 kV, 185 mm², XLPE, Three Core, Armoured) {Busbar VCB to Isolator} {50m+ Spare- 50m}

e) 11 kV Cable Termination Kit (185 mm², Outdoor)

f) 11 kV Cable Termination Kit (185 mm², Indoor)

LT Cable (1.1 kV, 3.5 Core, 70 mm2) {from Station Tfr}

Capacitor Bank (3-Ф, 50 Hz, 1800 KVAr) [ IS:2834 ]

Automatic Capacitor Switch (12 kV, 1250 A, 25 kA) [REC Spec. 20/1981]

Battery Bank with Battery Charger (15 No x 2V Cell, Lead Acid, 30 V, 200 AH)

Distribution Panel (30V, DC)

Distribution Panel (415 V, AC)Distribution Panel (415 V, AC) 200 Amp as incomer MCCB & 6 Nos 63 Amp MCCB as outgoing with voltmeter and Ammeter of 0.5 accuracy class alongwith phase indicating lamps of accuracy class 0.5

Super Strcture and Bus Bar Arrangement

(i) R.S. Joists, size 12800x250x125 mm 16 supports

(ii) R.S.Joists, size 4200x250x125 mm supports for Power Transformer's LA, Station Transformer LA, I/C, Power Transformer's CTs

(iii) M.S. channel iron 125x65 mm, X-arm @13.1 kg/m at 5% wastage for Bus-bar,Isolators,CT, LA's transformer etc.

(iv) M.S. angle iron 65x65 X-arm @ 5.8 kg/m & 5% wastage for body supports belt of Station transformer including 5% wastage

(v) Nuts & Bolts with Washers off sizes

BUS-BAR

(i) 3 Disc insulators Tension String complete with fitting

(ii) ACSR conductor 200 mm² at 10 % wastage

For jumpers at 2 m average 30 nos I.e.

(iii) Tee connections

(iv) PG clamps

Gantry FOR 33 kV

(a) Steel tubular pole 11 m long

(b) RCC muffs (2000mm) & concreting thereof for 1 No. out going Feeder

(a)5.5 m long M.S. channel iron 100X50X5 mm 9.56 kg/m Cross arms for Sub-Station With 1 No. out going Feeder (33kV)

(b) M.S. angle iron 50X50X6 mm 4.5 kg/m Cross arms for Sub-Station With 1 No. out going Feeder [ 4.2x3+5.33x2] (11kV)

(d) M.S. Half clamps

(e) Full Clamp

(f) Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

ACSR 100 mm² conductor for Jumpers [approx. 4 mtr/ phase]

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors)

Clamps for 1 Nos. out going Feeder

33 kV Isolator Moterised with ES

Gantry for 8 no. outgoing feeder

(a) Steel tubular pole 11 m long for 8 No. out going Feeder

(b) RCC muffs (2000mm) & concreting thereof for 1 No. out going Feeder

(a)4.2 m long M.S. channel iron 100X50X5 mm 9.56 kg/m Cross arms for Sub-Station With 1 No. out going Feeder (11Kv)

(b) M.S. angle iron 50X50X6 mm 4.5 kg/m Cross arms for Sub-Station With 1 No. out going Feeder [ 4.2x3+5.33x2] (11kV)

(d) M.S. Half clamps

(e) Full Clamp

(f) Nuts and Bolts of Various Sizes (Galvanised / Coated) [Preferably 16 mm Φ or more (with flat and spring washers)]

ACSR 100 mm² conductor for Jumpers [approx. 4 mtr/ phase]

Discs insulator sets (comprising 1 No. Disc: ^^(Porcelain, BS, 12 kV, 90 kN) including Dead End Clamps etc.) x (3 No. conductors)

Clamps for out going Feeder

11 kV Isolator

Cost of Earthing

Earthing of 33/11KV Substation

Earthing of 33 kV yard & equipment & 22 kV or 11kV panels M.S. flat 50x6 mm,wt. 2.4 kg/m At 5% wastage:- (a) Transformer Earthing at 3 points for 2 Nos Power Transformers (body & neutral) at 10 Mtr each 2X(3x10)x1.05=63 Mtr (b) For 4 No. LA's at 4.2 Mtr each 2X4.2x2x1.05=17.64 Mtr (c) For 22 nos. 33 kV super structure at 11.50 Mtr each 22x11.50x1.05 =265.65 Mtr i.e. 266 Mtr (d) For 32 Nos. VCB & CT body earthing at 10 m Each (32x10)x1.05 = 336 Mtr Total =682 mtr. i.e. 682X 2.4= 1638 ie 1.638 MT

GI Wire 6 No. SWG for screening etc.

Eye Block for screening

Tumbuckle for screening

GI Pipe 50 mm dia with holes of 16mm dia at 150 mm for centre to centre for 2 m distance from bottom For Transformer and for 11KV panels and fencing and Fixing of GI pipe 50mm with earth pit 10 nos per PSS Providing Coal=125 kg,Charcoal 23 kg ,Salt 122 kg,Sand 84 kg in each Earth Pit(Earth Pit Material)

MS plates 150x150x6mm for two connection

50x6 mm MS Flat connection with the mat to mat

Nut and bolts galvanized various sizes

Chequered plate cover 500x500x6mm i.e.11.8Kg

Providing MS Rod 40 mm dia 6 mtr long for Earth Matt Rods )(weight 9.9 kg per mtr) 16x6x9.9=950kg and Digging of 6 meter pits for earth rods 40 mm dia

Yard Lighting:-a) 9 m, Steel Tubular poles for yard lighting

b)18 W LED Lamp complete with fittings

c)Post Erection for gate

d)Clamps for GI pipe bracket

e)Underground cable 16 mm² for yard lighting

f)PVC cable size 6 mm² for connecting LED lamp supply

g)Junction box i/c MCCB and other allied

Lighting Emergency (3 No LED Bulbs with holders / wire)

control cable: 2x2.5 mm²

control cable: 4x2.5 mm²

control cable:12x2.5 mm²

3.5 core 95 mm² aluminium cable suitable for 415 V, AC

Fire Fighting Equipments as per TS

Safety Equipments & T & P as per TS

CIVIL WORKS

Control Room one Storey Building Sizes(14.7x14.8)sqm as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33202/2018

water supply and sanitary installation for Control Room Building.

Electrical Installation for control room building (for 60 points)

Septic Tank (1 Nos) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33254/2020

Rain Water Harvesting Tank (1 No per PSS) as per drawing of HPSEBL/SE(D)/ESHPSEBL/HAMIRPUR/33249/2020

Power Transformers Foundation suitable for upto 10 MVA (2 Nos) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33239/2020

Substation Transformer Foundation (1 No)

VCB Foundation (5 Nos) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33241/2020

Foundation of R.S. Joist supports (16 Nos) as per drawing of HPSEBL/SE(D)//ESHPSEBL/HAMIRPUR/33243/2020

Foundation of CT, PT & LA (14Nos) as per drawing of HPSEBL/SE(D)//ESHPSEBL/HAMIRPUR/33242/2020

Outdoor Cable Trench ( 80 mtr Per PSS) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33245/2020

Indoor Cable Trench ( 30 mtr trench per PSS) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33247-48/2020

Cost Of Boundary Wall (200Meter/Pss) as per drawing of HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33251-52/2020

Main Gate & Sub-Station Yard Gate(1 Nos) as per drawing of HPSEBL/SE(D)/ESHPSEBL/HAMIRPUR/33253/2020

Spreading of gravells/ Shingles in yard (30CUM ) as per drawing of HPSEBL/SEDES/SSD-478/2021-22-7972-79/2021

Formation of drainage system around the substation around 60x40mtr yard (200 Meter) as per drawing of

Firewall Protection as per drawing HPSEBL/SE(D)/ES HPSEBL/HAMIRPUR/33244/2020

Chain Link Fencing with wooven mesh of GI wire 15MX30M

Cost of Soil Testing & Contour plans & design

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth in all leads and lifts, as directed by Engineer-in-charge. All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand) : 8 graded stone aggregate 40 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form work for :

4.3.1 Foundations, footings, bases for columns

Retaining walls, return walls, walls (any thickness) including attached pilasters,buttresses, plinth and string courses fillets, kerbs and steps etc.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing weapholes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 110 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 Providing weep holes in plain retaining/reinforcement/Breast wall with 110mm dia. PVC pipe

Stone filling behind retaining wall

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50metres.