Repair of wornout signalling gears, attending defective signalling cables and ancillary works and to enchance the reliability of signalling gears in HMRDC sections over Mysur division.

C-Schedule C [Execution Portion] 1382544.00 Below/P

D-Schedule D [ Supply and Installation Portion] 3351144.00 Below/P

E-Schedule E [Non SOR Items]

Supply of Universal locks with one key for every ten locks. 1602697.0

Supply, Installation, testing and commissioning of SMPS based Integrated Power Supply (IPS) upto 6 Lines in RE area confirming to RDSO Specification No. RDSO/SPN/ 165/2023 (Ver. 4.0) with latest amendment with STR No:- SIQ 0110 Ver. 3.0 or latest along with B & C Class SPDs,63 Amps fuse, status monitoring panel as per Drawing No.B/SG/Proj/BNC/ IPS /PI-4L/RE/01 of dated 06- 10-2021 enclosed as Annexure A and B. IPS should be supplied with (55+5@ 61<41@ Nos. of uncharged LMLA Secondary Cells 2V-200AH/2V-300AH(For RE section 2V/200AH for non RE section 2V/300AH) as one set for one IPS confirming to QA IRS:S-88/2004 Low Maintenance Lead Acid 02 Stationary Secondary Cells For S&T Installations along with 16 Sqmm cable for each IPS set is (50 Mtrs Red + 50 Mtrs Black + 50 Mtrs Green) = 150 Mtrs. SPECIAL CONDITIONS:-1. Including supply of all the accessories required for installation. The supplier shall take up installation , wiring, testing and commission with minimum one month prior notice period from Railways. 2.All the required cables/ Miscellaneous items like wooden plank,ladder etc for installation and commissioning shall be supplied as part of the work. 3.Supply, installation, testing and commissioning of SPDs (class B&C) are covered in scope of this work. 4. Contractor should make the power supply arrangments if any required for charging the supplied cells at site. contractor should arrange the industrial grade diluted H2SO4 for the charging of cells. The cells should be charged as per specification enclosed. RDSO/SPN/165/2023 Ver 4.0

Supply of Digital Megger with range selection of 500V,100V,50V. Make Rish Insu 10 or better.

Manufacturing, Supply, painting and fixing of markers of G/P/C/A/IB Markers/Number plates with engineering grade reflective sticker on MS sheet with clamps asper drawings/as per site incharge. including all fixing materials.

Supply of electric track drilling machine with suitable horizontal stand with attachments to drill holes of various sizes up to 7mm to 13mm Make Rallywolf Model WD 34 C or better. 110V AC

Supply of Digital Earth Tester Det-1 with metal carrying box and auxiliary earthing net Make Wago or better.

Supply of Track lead junction box - FRP type with 4 terminals and stumps with necessary inspection as per specification/ drawing enclosed.

Supply of NON-AC Immunized Relays, Plug-In-Type, style QN1, 8F/8B Contacts, DC 08 Neutral line Relay, Working voltage 24V DC, metal to carbon, with plug bord, retaining clip and connectors as per RDSO Specification No BRS:930,IRS: S: 34 & IRS: S: 23, STR: SIQ 0420 Ver.1 or latest,. The Interlocking code for this relay shall be ABCDF.

Supply of Key Lock Checking Relay (KLCR) working on24V DC, AC Immunized with 09 different ward combinations and contact configuration 4F/4Bwith 2 extra ward plates and with case, RDSO spec no. RDSO/SPN/219/2016 ver 1.0 with amendment or latest, confirming to IRS S-23, S-34 & S@ 45<44@ IRS S:46

"Bush Cutter Machine Make: Honda Model: (HONDA 50 HP BUSH CUTTER (BRUSH CUTTER UMK450T U2NT) Heavy DutY or better "

Painting of two coats of synthetic enamel paint overone coat of primer on the following after scraping & cleaning surface wherever necessary with contractor'own supply of paints.Wherever required contractor shall apply coating of epoxy paint also as per instructions of 11 site-in-charge.Epoxy paint will be supplied by Railways. NOTE :- The paint and primer should be from M/s Asian paints Co. Ltd.,. The paints will be primer (IS 5660 of 1970) the Aluminium synthetic black enamel (IS 2932 of 1974) brilliant white and yellow Painting two coats of enamel paint over one coat of primer. "iii) Main Signal Post with Signal Units, Surface base and complete fittings as per Central Railways standard practice."

iv) Shunt signal post with signal unit, surface base as per Central Railway's Standard Practice."

v) Track lead Junction Box. (Black enamel outside only)

vi) Point Machine with ground connections complete (Point Machine with Black enamel only outside and ground connections with Red Oxide)"

"Lettering / Numbering of Signals, Point Machine, Track Lead Junction Boxes, Block Joints, Apparatus Cases etc. (each item to be taken as One Unit) This work will be carried out as per the standard practice being followed in Central Railway."

Fabrication supply and fixing of C clamp for clamping GI pipe 100mm in tunnels walls 16 at interval of 2 meter. The work consist of:- Supply of 60cm length x4cm widthx0.4cm thickness MS flat iron C clamp and fixing of GI pipes on the tunnel walls by using the C clamps (all the materials required for this work shall be supplied by the contractor except GI pipe

Additional input datalogger

Software modificaton & validation at site

Data base updating at central place

Supply, testing, installation & commissioning of Digital mother board for Datalogger with accessories. As per RDSO specification IRS:s:99-2006 (Amdt-3)

Supply, testing, instllation & commissioning of 64 Digital stack cards with ribbon cables and acessories. As per RDSO specification IRS:s:99-2006 (Amdt-3)

Supply, installation & wiring of 128 Tag block for Datalogger with all connected accessories. As per RDSO specification IRS:s:99-2006 (Amnd-3)

"Supply of Dominos and alteration of existing operating control cum indication panel. [Per Unit = Per Domino]"

Blue print of As made negative size of A3

Blue print of As made negative size of A2

Blue print of cable core & Cable route plan

Emergency sliding boom. Supply of Sliding Boom Type Gate as per E.Rly/Signal 27 Workshop /HWH's Drg. No. BSA/29/730, BSA/29/731, BSA/29/737. This includes supply of 5 nos 'E' type Lock with Key as per IRS Spec. No. IRS:S-30/64 with Latest Amdt and as per Drg. No. SA-3376/M with latest admt. Ward No. to be decided by the site engineer. 'E' type lock to be fixed on MS Plate as per Site requirement.

Fixing in position and commissioning of Sliding Barrier Boom Set (one set will consist of two sliding barrier boom, one for either side of track) this include carry out civil masonary work at site like digging of pits for foundations, casting of RCC foundation and fixing of foundation bolts (12 28 nos. in each site of size 18"x18"x36"). This also include loading, unloading and leading of all the material to site of work from the store of Concerned SSE/Sig/ Incharge (One set at each location) This include complete sliding gate in working order as per instruction of Railway Engineer at site and painting of sliding boom type barrier of LC gate with metallic paint, similar to Asian paint or better .All materials except sliding boom gate & 'e' type lock with key to be supplied by the contractor.

Excavation of pit and concreting foundations for resting stand/meeting stand (approx.10nos) for sliding boom erection allrequired materials for foundation like, sand, cement, jelly and other misc. materials are to be arranged by contractor

Provision of extension stamper rails for extending the height of sliding booms, where 30 uneven surfaces are available at site. the work involves, transportation of rails, cutting of rails, welding of supporting anchoring plates on either sides, and other misclleneous works as instruted by railway incharge supervisors all materials reqiured for the work excluding rails shall be supplied by contarctor.[Per Unit= Per Stamper]

Supply of Electronic Time Delay Units (/60 sec.s), Working Voltage 24V DC with plug boards, connectors and retaining clips as per RDSO specification No. IRS:S-61/2000 , STR: SIQ 422 Ver1.0 or latest.

"Supply & installation of Remote Terminal Unit (RTU) to monitor 128 Digital and 16 32 Analog inputs as per IRS: S99/2006 (Amd3) or latest. With one number of inbuilt dual card leased line modem for networking purpose. The RTU should be compatible for networking with existing NMDL system"

Supply & Installation of GSM & GPRS Modem.

Supply of Veeder Counter for 24 V DC 23.3mA

Supply & installation of wireless MODEM adopter card

Item Breakup - A-Schedule A [SOR Items]

11000.00 except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.3 Mtrs. Laying of cables is not included in this schedule.

500.00 except hard rocky areas including clearing of roots of trees, rocks, bushes etc. to a depth of 1.0 Mtrs and to a width of 0.5 Mtrs. Laying of cables is not included in this schedule.

200.00 the Passenger Platform, trenching to a depth of 0.6m to accommodate the additional cables, replacing the slabs removed after the cables are laid and replastering with cement mortar, refilling the trench by ramming and consolidating it as per the instructions of Railway Representatives at site. Laying of cables is not included in this schedule. [Cement, river sand and all other miscellaneous materials required for the work shall be supplied by the Contractor].

100.00 track crossing of cables, laying of DWC/ RCC pipes with collar/coupling, refilling of trench by ramming and consolidating it as per the instructions of Railway representative at site. During excavation of trench it has to be ensured that the excavated soil does not mix with the ballast available. The depth of 1m trench shall be from the bottom of sleepers for track crossings. Laying of cables is not included in this schedule.(Supply of DWC/RCC pipes with couplers/ collars is not included in this schedule). MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

100.00 road crossing of cables, laying of DWC/ RCC pipes with collar/ coupling, refilling of trench by ramming and consolidating it and resurfacing it to the original position. Laying of cables is not included in this schedule. (Supply of DWC/RCC pipes with couplers/ collars is not included in this schedule).

300.00 laying with offset at both ends and with couplings over RCC Bridges/ Drainage/ Culverts with concrete masonry supports of size 300mm x 300 mm x 300 mm at an interval of 2m. The ends of the pipes shall be closed with brick masonry work so that no cable is exposed, The work shall be carried out as per the instructions of Railway representative at site. (Supply of GI pipes with couplings and laying of cables is not included in this schedule.)[Stone jelly of size 20/25mm, bricks, sand, cement and all other miscellaneous materials required for the work shall be supplied by the Contractor].

30.00 laying with offset at both ends and with couplings over girder bridges by fixing on suitable MS Clamps at an interval of 2 Mtrs. The ends of the pipes shall be closed with brick masonry work so that no cable is exposed, The work shall be carried out as per the instructions of Railway representative at site. Supply of GI pipes with couplings and laying of cables is not included in this schedule.[MS angles, flats, bolts and nuts for manufacturing fixing clamps, bricks, river sand , cement and all other miscellaneous required for the work shall be supplied by the Contractor].

30.00 laying in hard rocky area with off sets at both ends duly supported by concrete blocks of size 300mm x 300 mm x 300 mm at an interval of 2m. The ends of the pipes shall be closed with brick masonry work so that no cable is exposed, The work shall be carried out as per the instructions of Railway representative at site. Supply of GI pipes with couplings and laying of cables is not included in this schedule.[Stone jelly of size 20/25mm, bricks, sand, cement and all other miscellaneous materials required for the work shall be supplied by the Contractor].

10000.00 cables as per cable plan in cable trenches, masonry ducts, RCC Pipes, DWC pipes, GI Pipes etc.(Supply of cables is not included in this schedule).

11000.00 width throughout, with earth after laying of cables, and consolidating the trench by ramming and leveling.

500.00 width throughout, with earth after laying of cables, and consolidating the trench by ramming and leveling.

200.00 No.CSTE/CN/OFC/1. The lettering on the cable marker shall be "SIG" / "TELE" / "OFC" as per the instructions of Railway representative at site. MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

200.00 300mmX300mm, casting of concrete foundation of size 300mmX300mmX300mm and Placing of RCC cable markers on top of the foundation and refilling the pit and consolidating it by ramming. The cable markers shall be provided at an interval of 20 Mtrs. within station limits and 50 Mtrs. outside station limits throughout the cable route, diversions and also at every track/road/crossing.

200.00 103.5mm inner dia & 120mm outer dia conforming to specification No. IS 14930(Part 2): 2001 with one coupler for every 6m of pipe as specified in Vol.II of the Tender document.

300.00 as specified in Vol.II of the Tender document.

30.00 as specified in Vol.II of the Tender document

30.00 as specified in Vol.II of the Tender document

4.00 and erection of apparatus case full size as per Drg. No.SG/CN/02/6 and fixing of 2 Nos. of 'E' type locks, one for the front door and another for the back door, fixing of one hard wood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints.(Supply of apparatus case is not included in this schedule).[Foundation bolts & nuts, 'E' type locks, cement, river sand, stone jelly of size 20/25 mm, hardwood plank of 37mm thick, paints, varnish, fixing bolts & nuts and all other miscellaneous materials required for the work shall be supplied by the Contractor.]

2.00 and erection of apparatus case half size as per Drg, No.SG/CN/02/7, fixing one 'E' type lock for the front door and latching arrangement for the back door, and fixing of one hardwood shelf plank 37mm thick and painting the apparatus case inside and outside with one coat of red-oxide and two coats of aluminium paints.(Supply of apparatus case is not included in this schedule).[Foundation bolts and nuts, cement, 'E' type locks, river sand, stone jelly of size 20/25mm, 37mm hard wood planks, latching arrangements, paints, varnish, fixing bolts & nuts and all other miscellaneous materials required for the work shall be supplied by the Contractor] MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

39.78 existing terminals/ fuse blocks in apparatus cases/ battery boxes/ CT boxes/ cable termination racks as per approved circuit diagram. The terminal particulars are to be repainted /corrected on the doors of apparatus cases/ battery boxes/ cable termination boxes and FTOT index board as instructed by Railway representative at site. This work includes closing the opening created for entry of new cables in the apparatus cases with masonry brick work and sealing the bottom of the apparatus cases/ cable termination racks with cable compound. [Paints, wire PVC 3/0.75mm and 16/0.2mm copper, sealing compound, bricks, cement, river sand and all other required miscellaneous materials shall be supplied by the contractor].

93.16 cables and internal wiring on terminal/ fuse blocks in new apparatus cases, cable termination boxes and in gate Lodges excluding cable termination rack at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing of Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each apparatus case, varnishing all teakwood items, fixing of terminals/ fuse blocks on the terminal board, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as per approved circuit diagram and cable plan, painting of particulars on sleeves and also on the inner side of the doors of apparatus cases. After terminations are over, the side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter-space filled with river sand up to base level and the bottom surface shall be sealed with sealing compound. (Supply of PBT terminals and Fuse blocks is not covered in this schedule). [Cement, teakwood cable clamp 50mm x 50mm, base planks 100mm x 25mm, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, PVC/Nylon sleeves, varnish, paints, bolts, nuts and washers, Non-deteriorating type of fuses of various capacities, Aluminium cable tags, sealing compound, country bricks 220mm x 100mm x 60mm, copper bus bars, brass screw, river sand, wire PVC3/0.75mm copper and other miscellaneous materials shall be supplied by the Contractor]. a. Termination on 25/60mm PBT terminals (new location) (Phynolic sheet) MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

100.00 cables and internal wiring on terminal/ fuse blocks in new apparatus cases, cable termination boxes and in gate Lodges excluding cable termination rack at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing of Phynolic synthetic industrial fibre base fine weave cotton fibre board 6mm thick for terminal board to suit each apparatus case, varnishing all teakwood items, fixing of terminals/ fuse blocks on the terminal board, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as per approved circuit diagram and cable plan, painting of particulars on sleeves and also on the inner side of the doors of apparatus cases. After terminations are over, the side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter-space filled with river sand up to base level and the bottom surface shall be sealed with sealing compound. (Supply of PBT terminals and Fuse blocks is not covered in this schedule). [Cement, teakwood cable clamp 50mm x 50mm, base planks 100mm x 25mm, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, PVC/Nylon sleeves, varnish, paints, bolts, nuts and washers, Non-deteriorating type of fuses of various capacities, Aluminium cable tags, sealing compound, country bricks 220mm x 100mm x 60mm, copper bus bars, brass screw, river sand, wire PVC3/0.75mm copper and other miscellaneous materials shall be supplied by the Contractor]. a. Termination on 25/60mm PBT terminals (new location) (Phynolic sheet) b. Termination on PBT fuse block (new location) (Phynolic sheet) MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

100.00 cables and internal wiring by fixing additional terminals/ fuse blocks on the existing terminal boards of apparatus cases, cable termination boxes etc. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, varnishing all teakwood items, fixing of terminals/ fuse blocks, on the existing terminal boards, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as per approved circuit diagram and cable plan, painting of particulars on sleeves and also on the inner side of the doors of apparatus cases. After terminations are over, the side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter- space filled with river sand up to base level and the bottom surface shall be sealed with sealing compound. (Supply of PBT terminals and Fuse blocks is not covered in this schedule).[Cement, teakwood cable clamp 50mm x 50mm, base planks 100mm x 25mm, PVC/Nylon sleeves, varnish, paints, bolts, nuts and washers, Non-deteriorating type of fuses of various capacities, Aluminium cable tags, sealing compound, country bricks 220mm x 100mm x 60mm, copper bus bars, brass screw, river sand, wire PVC3/0.75mm copper and other miscellaneous materials shall be supplied by the Contractor]. a. Termination of cables on 25/60mm PBT terminals (existing location)

10.00 cables and internal wiring by fixing additional terminals/ fuse blocks on the existing terminal boards of apparatus cases, cable termination boxes etc. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, varnishing all teakwood items, fixing of terminals/ fuse blocks, on the existing terminal boards, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as per approved circuit diagram and cable plan, painting of particulars on sleeves and also on the inner side of the doors of apparatus cases. After terminations are over, the side openings of apparatus case foundation shall be closed with brick work, cement plastered, the inter- space filled with river sand up to base level and the bottom surface shall be sealed with sealing compound. (Supply of PBT terminals and Fuse blocks is not covered in this schedule).[Cement, teakwood cable clamp 50mm x 50mm, base planks 100mm x 25mm, PVC/Nylon sleeves, varnish, paints, bolts, nuts and washers, Non-deteriorating type of fuses of various capacities, Aluminium cable tags, sealing compound, country bricks 220mm x 100mm x 60mm, copper bus bars, brass screw, river sand, wire PVC3/0.75mm copper and other miscellaneous materials shall be supplied by the Contractor]. b. Termination of cables on PBT fuse block (existing location) MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

4.00 of suitable size to hold up to 4/ 8/ 12/ 20 relays as required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit and Point control circuits, fixing of plug boards, relays, resistors and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, wiring and termination as per approved circuit diagram and painting the particulars.(Supply of all types of relays, plug boards, connectors and retaining clips is not covered in this schedule).[Wire PVC copper, 3/0.75mm and 16/0.2mm copper, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, MS flats 25mm x 6mm brass bolts and nuts, paints, soldering materials, resistors, condensers and all other miscellaneous materials required for the work shall be supplied by the contractor]. c. Wiring of Signal/ Point/ LC control circuit (up to 12 relays)

6.00 of suitable size to hold up to 4/ 8/ 12/ 20 relays as required by Railways and fixing them in apparatus cases for all types of signal control circuits, LC gate control circuit and Point control circuits, fixing of plug boards, relays, resistors and electrolytic condensers on Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, wiring and termination as per approved circuit diagram and painting the particulars.(Supply of all types of relays, plug boards, connectors and retaining clips is not covered in this schedule).[Wire PVC copper, 3/0.75mm and 16/0.2mm copper, Phynolic synthetic industrial fibre base fine weave cotton fibre sheet - 6mm thick to IS specification 2036 - 1995 - Type F5, for fixing resistors and condensers, MS flats 25mm x 6mm brass bolts and nuts, paints, soldering materials, resistors, condensers and all other miscellaneous materials required for the work shall be supplied by the contractor d. Wiring of Signal/ Point/ LC control circuit (up to 20 relays)

550.00 disturbing the terminations and equipments inside. The work involves scraping of old paint, applying one coat of Red oxide and two coats of Aluminium paint on the inside and outside the apparatus cases, and painting of termination and equipment particulars on the doors of the apparatus cases, as instructed by Railway representative at site. [Aluminium paint, red-oxide and all other miscellaneous materials required for the work shall be supplied by the Contractor]. a. Painting of existing apparatus case - Full size MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

80.00 disturbing the terminations and equipments inside. The work involves scraping of old paint, applying one coat of Red oxide and two coats of Aluminium paint on the inside and outside the apparatus cases, and painting of termination and equipment particulars on the doors of the apparatus cases, as instructed by Railway representative at site. [Aluminium paint, red-oxide and all other miscellaneous materials required for the work shall be supplied by the Contractor]. b. Painting of existing apparatus case - Half size

100.00 particulars of functions in the existing apparatus cases, cable termination boxes, etc., on the PVC/ nylon sleeves and painting of new nomenclature on the existing signaling gadgets. This work includes carrying out alterations of particulars on the inner side of the doors of apparatus cases, re-numbering of apparatus cases and cable termination boxes. [Paints and all other miscellaneous materials required for the work shall be supplied by the Contractor]. a. Alteration to painting particulars (apparatus case - Full size)

20.00 particulars of functions in the existing apparatus cases, cable termination boxes, etc., on the PVC/ nylon sleeves and painting of new nomenclature on the existing signaling gadgets. This work includes carrying out alterations of particulars on the inner side of the doors of apparatus cases, re-numbering of apparatus cases and cable termination boxes. [Paints and all other miscellaneous materials required for the work shall be supplied by the C o n t r a c t o r ] . b. Alteration to painting particulars (apparatus case - half size)

6.00 particulars of functions in the existing apparatus cases, cable termination boxes, etc., on the PVC/ nylon sleeves and painting of new nomenclature on the existing signaling gadgets. This work includes carrying out alterations of particulars on the inner side of the doors of apparatus cases, re-numbering of apparatus cases and cable termination boxes. [Paints and all other miscellaneous materials required for the work shall be supplied by the C o n t r a c t o r ] . c. Alteration to painting particulars (apparatus case-quarter size/ CT box)

6.00 as per Drg.No.SG/CN/02/9 using metallic templates, for erection of colour light signals up to 4 aspects.[Foundation bolts, cement, river sand, stone jelly of size 20/25mm dia and all other miscellaneous materials required for the work shall be supplied by the Contractor]. MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

6.00 mounting of colour light signal up to 4 aspects complete on Signal pole/ Off-set bracket, (for LED/ filament bulbs) with lenses, triple pole lamp holder, filament switching units, CLS transformer, current regulators (whichever is applicable), fixing of ladder with platform complete and concreting of ladder shoe, fixing of number plates, marker board, lens guard, termination of tail cables, wiring of signal unit with PVC wire 3/0.75mm copper, provision of EWS locks, and painting of one coat of red oxide and two coats of aluminium/ enamel paints. When the aspect is fixed on Offset bracket using 'U' bolts and nuts, a through bolt shall be provided by drilling a hole in the signal pole to prevent the offset bracket from sliding down.(Supply of surface base, Offset bracket, CLS pole, CLS aspects complete, ladder with shoes and platform, LED aspects, current regulators, lamp holders, lamps, filament switching unit and CLS transformer is not covered in this schedule). ['U' bolts and nuts, through bolts and nuts, cement, stone jelly 20/25mm dia, river sand, Signal Collar Rings, wire PVC 3/0.75mm copper, lens-guard, all fixing bolts and nuts, lead wool, paints PVC/Nylon sleeves, enameled number plates. enameled marker boards, EWS locks, and all other miscellaneous materials for the work shall be supplied by the Contractor].

2.00 way to 6 ways - complete/ fixing of additional limb to the existing route indicators, termination of tail cables, wiring as per approved circuits diagram using wire PVC 3/0.75mm copper, provision of required No of EWS locks, wire mesh, and painting.(Supply of junction type Route Indicators - complete and additional limb is not covered in this schedule).[3/0.75mm wire PVC, fixing bolts and nuts, EWS locks, wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the Contractor]. a. Fixing and wiring of direction type route indicator - 1 way

2.00 nuts, erection of Calling On Signals/ 'A' marker lights, termination of tail cables and wiring using wire PVC 3/0.75mm copper, provision of EWS lock, number plates/ marker boards and painting. The work also includes drilling suitable holes on the CLS post and provision of a through bolt with nut to prevent the Off-set bracket from slipping down. (Supply of Calling On Signal/ 'A' marker light, LED aspects/ holders & bulbs and Off set brackets is not covered in this schedule).['U' bolts and nuts, through bolts with nut, wire PVC 3/0.75mm copper, EWS lock, Enameled number plates, wire mesh, PVC/Nylon sleeves, paints and all other miscellaneous materials shall be supplied by the contractor]. MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

140.00 plates as per drawing No.TY/08/2008 with fixing arrangements and fixing them on the existing Signals as per the instructions of Railway representative at site.[Enameled number plates with fixing arrangements with bolts and nuts shall be supplied by the Contractor].

30.00 No.SG/SN/02/13 and earthing of metallic sheath and armour of all cables in all apparatus cases, relay room, equipment room, SM's room for block and control, and earthing of all equipments in apparatus cases, power room, relay rack, cable termination rack, control panel, signals, lever frames with MS flat 35mm X 6mm/19c cable (MS flat for closure by areas and MS flat/19c cable combination for farther areas) as per the instructions of Railway representative at site. The work includes painting of earth resistance value on the earth pit. Supply of 19C cable is not covered in the scope of this schedule.[MS flat for earthing 35mm X 6mm, cement, GI earth electrodes, common salt, charcoal, country bricks, river sand, soldering materials and all other miscellaneous materials required for the work shall be supplied by the Contractor].

15.00 IRS type and connecting all ground connections including wiring and termination in point machine and interconnections between point machine and CT box through PVC hose pipe with 3/0.75mm and 7/1.40mm copper wire and painting. This work includes provision of insulation to stretcher bars, throw bar lug and "D" bracket wherever required, cutting of notches on the point machines covers to suit crank handle configuration. (Combined type point machine with ground connection, uninsulated stretcher bar, throw bar lug and 'D' brackets will be supplied by Railways.[All types of insulations connected to point work, coal bengal, all type of bolts and nuts, washers spring/flat wire PVC 7/1.4mm copper, PVC hope pipe, paints, PVC/nylon sleeves and all other miscellaneous materials required for the work shall be supplied by the Contractor].

6.00 4.6m/ 3.6m tall with necessary inspection as per specification/ drawing/ description enclosed in this document. b. Supply of colour light Signal pole (3.6m)

6.00 140mm dia with necessary inspection as per specification/ drawing/ description enclosed in this document.

6.00 suit CLS pole 4.6m/ 3.6m tall, with necessary inspection as per specification/ drawing/ description enclosed in this document. b. Supply of ladder with platform and shoes for 3.6m CLS pole MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

6.00 10296.00 complete for 4/ 3/ 2 aspect with mounting socket, with necessary inspection as per specification/ drawing/ description enclosed in this document b. Supply of colour light Signal unit - 3 aspect

2.00 10868.00 arm - 1/ 2/ 3/ 4/ 5/ 6 way with mounting sockets, with necessary inspection as per specification/ drawing/ description enclosed in this document. a. Supply of Junction type route indicator - 1 way

2.00 complete with necessary inspection as per specification/ drawing/ description enclosed in this document. a. Supply of Calling On Signal

3.00 of cast iron with necessary inspection as per specification/ drawing/ description enclosed in this document. a. Supply of Off-set bracket (large)

44.00 and PBT Fuse blocks with necessary inspection as per specification/ drawing/ description enclosed in this document. a. Supply of PBT terminal - 25mm centre

100.00 and PBT Fuse blocks with necessary inspection as per specification/ drawing/ description enclosed in this document. b. Supply of PBT terminal - 60mm centre

100.00 and PBT Fuse blocks with necessary inspection as per specification/ drawing/ description enclosed in this document. c. Supply of PBT fuse block (without ND fuse)

420.00 the following capacities with necessary inspection as per specification/ drawing/ description enclosed in this document. e. Supply of secondary cells-2V-300AH capacity

6.00 12012.00 size) to suit Southern Railway standard with necessary inspection as per specification/ drawing/ description enclosed in this document: a. Supply of apparatus case - Full size

2.00 size) to suit Southern Railway standard with necessary inspection as per specification/ drawing/ description enclosed in this document: a. Supply of apparatus case - Full size b. Supply of apparatus case - Half size

20.00 of required ward Nos. with keys, with necessary inspection as per specification/ drawing/ description enclosed in this document. MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

420.00 the following capacities, on existing battery stand/ RCC slabs in the battery room. The work involves charging of secondary cells, fixing and connecting the batteries with strips, manufacture and fixing of teakwood terminal box, termination of cables, wiring with suitable wire PVC 7/1.40mm and 3/0.75mm copper through suitable PVC pipes/ casing properly clamped, provision of battery particulars board made of phynolic sheet 6mm thick of size 900mm x 1200mm with Aluminium grooved channel frame in the relay room. The particulars shall be digitally using good quality laminated gum sheet, provision of hydrometer -1 No. on a stand and battery tester-1 No. Charging of secondary cells shall be done by the contractor through reputed agencies(Supply of secondary cells is not covered in this schedule).[Teakwood plank 25mm thick for manufacturing termination box with locking facility, wire PVC 7/1.4mm and 3/0.75mm copper, anti- corrosive paint, varnish, PVC pipes/ casing, and all other miscellaneous materials required for this work shall be supplied by the contractor]. a. Installation of 2V-300AH cell on existing stand / slabs

70.00 boards, warning boards, STOP boards etc., as per standard practice and as per the instructions of Railway representative at site. (Supply of boards is not included in this schedule). [Paint and all other miscellaneous materials required for the work shall be supplied by the Contractor].

10.00 for fixing the same in LC/HP/FP Locks/SM slides and painting as per standard practice and instructions of Railway representative at site. (Supply of E type Locks, Keys, Paints, all types of screws, bolts & Nuts and all other miscellaneous materials shall be supplied by the Contractor).

15.00 machines (all types) including ground connections and other accessories available complete without any damage to the gadgets, accounting and stacking them neatly at a place as instructed by Railway representative at site. Total 5960650.30

Item Breakup - B-Schedule B [Supply Portion]

100.00 110 mm Outer Dia, 10 mm Wall Thickness, along with one coupler for every 6 Meters as per specification No. IS 4984: 2016 with latest amendments and Material Grade:PE 80.

10.00 Free Earth as per RDSO Spec No. RDSO/ SPN/197/2008 or latest and as per relevant Technical specification

2.00 131287.00 Channels- 110V AC, 2 Channels- 110V DC , 6 Channels- 24V DC) as per RDSO Spec./256/2002 or latest with 6 digit counter. MYSORE DIVISION-S AND T/SOUTH WESTERN RLY Total 557874.00

Item Breakup - C-Schedule C [Execution Portion]

100.00 based on RDSO Report No. BS - 105. This also includes insertion of HDPE Pipe of 110mm Outer dia in the Bore drilled.(Supply of HDPE Pipe is not included).

80.00 power cables and internal wiring on terminal/ fuse blocks in cable termination Rack at relay room. The work includes fixing of all new cables by teakwood clamp on teakwood base plank, fixing of Hylem sheet 10 mm thick for terminal board , varnishing all teakwood items, fixing of terminals/ fuse blocks on the terminal board, drilling of necessary holes, termination of cables, wiring, identification of cables using aluminium tags with letters punched neatly, as per approved circuit diagram and cable plan, painting of particulars on sleeves . After terminations are over, cable entry at the bottom shall be closed with , cement plastered, the inter- space filled with sand upto base level and the bottom surface shall be sealed with sealing compound. Cable armour to be soldered to earth.(Supply of cable termination racks is not included in this schedule). [All bolts and nuts with washers, Hylum Sheet 10 mm Thick, cement, sand, stone jelly, Teak wood base , paints a n d all other miscellaneous materials required for the work shall be supplied by the contractor]a. Termination on 25/60mm PBT terminals {Per Unit-Per Terminal}

1.00 50502.00 Single Section digital Axle counter (SSDAC) with High Availability. HA-SSDAC to be installed, wired, tested and commissioned by OEM as per guidelines issued by RDSO, wiring discipline should be as per RDSO TAN No. STS/E/TAN/6001 Version 1.0 or latest. The pre-commissioning checklist issued by RDSO for SSDAC to be prepared by OEM and jointly signed by OEM & Railway. Before commissioning of HA-SSDAC, OEM should submit site installation certificate.

200.00 pipe/DWC/HDPE pipe in which cable is already laid to a size of 300*300mm with 1:3:6 mortar. (All the matetrials required for the work should be supplied by the contractor) {Per Unit- RMT}

10.00 as per RDSO specification No.RDSO/ SPN/197/ 2008 or latest and as per Technical Specification

2.00 39526.00 Leakage Detector 12 channel . MYSORE DIVISION-S AND T/SOUTH WESTERN RLY

730.00 Technical manpower to carryout works like drawing, computation, write up etc., using computer, using software like AUTOCAD, MS Office etc., between 08.00 Hrs and 20.00 Hrs of the day with all expenses of transportation, accomodation, food, consumables etc., with all ascents, descents, taxes, octroi, cess, fees, duties with contractors cost etc., as per special conditions/specifications/regulations and as directed by ENgineer-in-charge. Note: The person engaged for providing the services shall be convergent with computer working knowledge in above software's."

730.00 to carry out miscellaneous/sundry works in Days the office/field between 08.00 hrs and 20.00 hrs of the day and accompanying Railway staff with all expenses of transportation, accomodation, food, consumables etc., with all ascents/descents, taxes, octroi, cess, fees, duties, with contractors tools and plants, materials, consumables, labour, crew, machineries with all lead and lift etc., complete as per special conditions, specification, regulation and as directed by Railway Engineer-in-charge. Total 1382544.00

Item Breakup - D-Schedule D [ Supply and Installation Portion]

2.00 Goods Warning Boards as per practice & SEM(Angle/Rail is to be supplied by Railway).

10.00 Calling-On/STOP/BSLB/Legend boards as per practice & SEM (Angle/Rail is to be supplied by Railway).

284.00 2840000.00 120/103 mm dia, 2 meter long in already dug cable trenches. The unit of RMT means two split pipes of 1 Mtr each. Material shall be supplied as per specification RDSO/SPN/204/2011 or latest" {Per Unit- RMT}

10.00 Handle Cum Key Lock Relay Box (of MS Sheet) along with LEDs, with approved type push buttons, Wago or similar Disconnecting type Terminal Blocks inlcuding DIN rail etc., as per tentative drawing enclosed. Installation, fixing and wiring of boxes for Key Lock Relays to be carried with Contractor's wiring and fixing material. The work shall be carried as per the instructions of site engineer.

2.00 43374.00 (Aqua-Ion Model No. ACAMB 4 Bed Type). Total 3351144.00