GE/SRA/T-10/2025-26

Amount

Taking down Cement Plaster including raking out Joints, hacking for Key, scrubbing down with Water and removing Debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L for complete removal of existing treatment on old painted surfaces of internal walls and ceilings by scrapping and removing treated surfaces with mechanical wall sander (having vacuum mechanism for suction) having minimum 1500 RPM, sanding pad of 80 grit size having 7"- 9" dia (as required) including cleaning, watering to make the surface clean and free from dust, etc including necessary scaffolding, safety and protective measures complete all as specified and directed.

M&L for Rendering (Internal) 12mm thick in cement mortar 1:6 on Brick Walls or on Concrete Surfaces, Plastered Surfaces finished Even and Smooth without using Extra Cement complete all as specified and directed.

M&L for Rendering (Internal) 15mm thick in cement mortar 1:6 on Brick Walls or on Concrete Surfaces, Plastered Surfaces finished Even and Smooth without using Extra Cement complete all as specified and directed.

M&L preparing undecorated Plastered surfaces of internal walls and treating with two coats of single component penetrative cum film forming interior water proofing coating (as per manufacturer's instructions) complete all as specified and directed. (MAKE: ASIAN PAINTS, SMARTCARE HYDROLOC / DR FIXIT, SURESEAL / BERGER, DAMPSTOP ADVANCED or similar products as approved by GE) NOTE: This item shall be executed only for surfaces severly affected by moisture before applying top coat finishes.

M&L for preparation of surfaces and applying one coat of cement primer suitable for internal walls complete all as specified and directed.

M&L for applying 1.5mm thick Wall Putty (in two coats) over internal plastered surfaces of wall/cement board incl rubbing down with Sand Paper of proper grade to obtain a Smooth Finished Surface complete all as specified & directed.

M&L for applying Two Coats of Acrylic Distemper (as approved), mixed with stainer for achieving the desired shade and applied with rollers on walls/cement boards complete all as specified and directed.

M&L for Rendering 5.0mm thick in cement mortar 1:3 on Concrete Surfaces of Ceilings, Plastered Surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparing newly Plastered surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and directed.

M&L for 15 mm thick plastering in two layers, 10 mm + 5 mm in cement mortar 1:4, top layer of 5 mm thickness mixed with with water proofing compound (as per manufacturer's instructions) on external surfaces of brick/stone walls or concrete surfaces finished even and fair upto 4 storey height including necessary scaffloding complete all as specified and directed. Note : Water Proofing compound shall be measured and paid seperately as "Supply only".

Supply only Liquid Water Proofing Compound, ISI Marked, as approved, complete all as specified and directed.

M&L for preparation of newly plastered surfaces of external walls and applying a coat of suitable exterior cement primer, on new wall surfaces of any description, over 10cm width or girth not otherwise described, upto 4 storey height incl necessary scaffloding complete all as specified and directed.

M&L for applying two coats of exterior acrylic emulsion paint (having anti-dust & anti-algae properties), applied with rollers to new wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufacturer's instructions, upto 4 storey height including necessary scaffloding complete all as specified and directed.

M&L for Rough Cast Plaster on Brick Walls consisting Under Coat of Cement and Sand Mortar 1:3 not less than 10mm thick and while it is still in Plastic state the Rough Cast Mixture consisting of Crushed Stone or Fine Gravel mixed with Coarse Sand and Cement in the Ratio 1:1:1 shall be applied and finish Even, complete all as specified and directed.

M&L preparing newly Rough Cast plastered surfaces of exterior Walls and applying a coat of suitable exterior Primer (as per Manufacturer's instructions), complete all as specified and directed.

M&L for applying two coats of Exterior Emulsion Paint (having anti-dust & anti-algae properties) with approved Tint (as per Manufacturer's instructions), on rough cast plastered surfaces complete all as specified and directed.

M&L preparing old Distempered surfaces of Walls/cement boards including filling the existing Nails/Screw Holes, etc. and applying One Coat of Acrylic Distemper (of approved tint) with rollers complete all as specified and directed.

M&L for preparing old treated/decorated surfaces of ceilings and applying One Coat of White Wash, complete all as specified and directed.

M&L for preparing old treated/decorated surfaces of walls and applying One Coat of White Wash, complete all as specified and directed.

M&L preparing old Treated/Painted Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (First quality), complete all as specified and directed.

M&L preparing old decorated/painted Wood and Wood Based Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying One Coat of Synthetic Enamel Paint (1st quality), complete all as specified and directed.

M&L preparing old Decorated/Treated Plastered surfaces of Exterior Walls upto Four Storey by brooming down or steel wire brushing and scraping down, filling of cracks with suitable paste and applying with rollers One Coat of Exterior Emulsion Paint (having anti-dust & anti-algae properties) with approved Tint, applied with rollers to wall surfaces of any description, over 10cm width or girth not otherwise described, as per manufacturer's instructions, upto 4 storey height including necessary scaffloding complete all as specified and directed.

-ditto- but with One Coat of Exterior Emulsion Paint (having anti-dust & anti-algae properties) on old Decorated/Treated Rough Cast Plastered surfaces.

S&F in repair Non-asbestos Fiber Cement Building Boards 6.0mm thick, fixed to Walls with Rawl Plugs and Steel Screws complete all as specified and directed.

Demolition Brick work built in Cement Mortar and in any Position including all Quoins, Arches and Pillars, etc., and removal of debris outside AF land complete all as specified and directed.

M&L for Brick Work with Fly-Ash Bricks (Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and directed.

M&L Brick work using Serviceable Bricks obtained from Item No. 21 here-in-before including removing old Mortar, Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in cement mortar 1:6, complete all as specified and directed.

Demolition Cement Concrete (Reinforced) of kitchen slab, and similar work (reinforcement cut as required to facilitate demolition) and removing debris, etc. to Outside MOD Land, complete all as specified and directed.

M&L Reinforced Cement Concrete 1:2:4 type B0 (12.5mm graded stone aggregate) as in Shelves, Chajja, Facia, Sunshade and Similar Items and smooth finishing at Top side using extra Cement, complete all as specified and directed. (NOTE: MS reinforcement & Formwork shall be measured and paid seperately)

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (horizontal or sloping) for rough finished surfaces complete all as specified and directed.

M&L TMT Bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hoping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia or securing with Clips, complete all as specified and directed.

M&L TMT Bars 06-08mm dia, cut to length bent to shape required including cranking, bending spirally for hoping for Columns, hooking Ends and binding with and including Mild Steel Wire (annealed) not less than 0.9mm dia or securing with Clips, complete all as specified and directed.

Taking down damaged/unserviceable PVC Chowkat or Frame not exc. 1.50 Sqm Each with shutter (without taking off shutter from the frame) and removal from site complete all as specified and directed.

S&F factory made single extruded WPC (Wood Polymer composite) solid door/window/ceosetory windows & other frames/chowkhat of size 45 X 75mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibres (wood powder/rice husk/wheat husk) and non-toxic additives (maximum toxicity index of 12 for 100 grams) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N(Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with mild steel hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. (NOTE: MS hold fast/lugs or SS dash fasteners shall be paid for seperately. For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made)

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and shall be fixed with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed. (Note: Butt hinges and necessary S.S screws shall be paid separately)

S&F Butt hinges, 100mm long, stainless steel complete all as specified and directed.

S&F Aluminium alloy Handle 125mm long, cast type, anodised, complete all as specified and directed.

S&F Aluminium Barrel Tower Bolt 150 mm long, extruded section, complete all as specified and directed.

Resecuring or easing & adjusting without taking down shutters of any description, area exceeding 1.0 sqm but not exceeding 2.0 sqm each complete all as specified and directed.

Taking down Shutter of any description, area exc 1.00 Sqm and not exc. 2.00 Sqm Each and Refixing in the Same Opening, after resecuring or easing and adjusting, etc., complete all as specified and directed.

Taking down damaged/unserviceable Steel/Wooden Chowkat or Frame exc. 1.50 Sqm but not exc. 4.00 Sqm Each with shutter( without taking off shutter from the frame) and removal from site complete all as specified and directed.

Taking down damaged/unserviceable Steel/Wooden Chowkat or Frame not exc. 1.50 Sqm Each with shutter( without taking off shutter from the frame) and removal from site complete all as specified and directed.

S&F Pressed Steel Frame of size 105x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates incl necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and directed.

S&F Pressed Steel Frame of size 125x60mm using 1.25mm thick Mild Steel Sheets for Doors with One or More Rebates incl necessary Fixing Lugs, Hinges, Lock Strike Plate, etc., complete all as specified and directed.

Taking down Shutters of any description exc 1.0 sqm and not exc 2.0 Sqm each and removal from site complete all as specified and directed.

M&L for Flush Shutters of 30mm thick, solid core construction with block board core and plywood face panels, cmmercial type on both sides and fitted to Steel Frame, complete all as specified and directed.

M&L Panelled Shutter 35mm thick of Second Class Hardwood with Panels of 12mm thick Veneered Particle Board medium density wood with commercial face veneered both side and fitted to Chowkats, having size of Rail and Stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and directed.

M&L Glazed and Skeleton Shutter 35mm thick of Second Class Hardwood prepared to receive Gauge/Glass (without Sash Bars) fixed with mitred beeds supplied and fitted to Chowkat and securing Glass, Gauge, etc. sizes of Members of Shutter as specified in SSR Part-I, Section-8, Clause 8.24(a), complete all as specified and directed.

M&L Cement Concrete 1:3:6 type C0 (12.5mm graded stone aggregate) as in Filling Back side of Chowkats, complete all as specified and directed.

S&F Aluminium Barrel Tower Bolt 200mm long (weight not less than 210 Gram), extruded section, complete all as specified and directed.

S&F Aluminium alloy, anodized, Sliding Door Bolt 250mm long with Hasp Staple (Bolt type) and Fixing Clips of Sheet cast or extruded section and fixing Bolts and Sliding Bolts of extruded section and fixing, complete all as specified and directed.

S&F Aluminium alloy Handle 150mm long (weight not less than 100 Gram), cast type, anodised, complete all as specified and directed.

S&F in repairs Floor Door Stopper 150mm in size, Aluminum alloy Body and Tongue with Hard Drawn Steel Spring (weight not less than 90 Gram), complete all as specified and directed.

S&F in repairs Aluminium Barrel Tower Bolt 200mm long (weight not less than 210 Gram), extruded section, complete all as specified and directed.

S&F in repairs Aluminium Barrel Tower Bolt 150mm long (weight not less than 210 Gram), extruded section, complete all as specified and directed.

S&F in repairs Aluminium alloy, anodized, Sliding Door Bolt 250mm long with Hasp Staple (Bolt type) and Fixing Clips of Sheet cast or extruded section and fixing Bolts and Sliding Bolts of extruded section and fixing, complete all as specified and directed.

S&F in repairs Aluminium alloy Handle 150mm long (weight not less than 100 Gram), cast type, anodised, complete all as specified and directed.

S&F in repairs Door Spring of Mild Steel 150mm long, Ordinary Rat Tail type, Rod pattern Springs including Roller and Roller Plate welding with frame , etc., complete all as specified and as directed.

M&L preparing new Wood and Wood Based Surfaces of any description, not otherwise described, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Coat of Pink Primer, complete all as specified and directed.

M&L preparing new or previously untreated Steel and Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, etc. and fixed complete all as specified and directed.

S&F in repair Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples, etc complete all as specified and directed.

Taking down Steel Window/Ventilator, fixed type, of any description, area not exc.1.00 Square Metre Each, complete all as specified and as directed.

Taking down Steel Window Frame (without taking off Shutter from the Frame) of any description including Guard Bars/Grill, exc. 1.00 Square Metre but not exc. 2.00 Square Metre Each, complete all as specified and as directed.

S&F Steel windows or ventilators, fixed type, with glazing bars complete all as specified and directed

S&F Steel Window Box type using ERW ‘P’ Section comprising Double Frame for Gauged and Glazed Skeleton Shutters, having Outer Frame of Section 50x25mm and Inner Frame of Section 40x20mm, jointed internally with Mild Steel Flat Iron 40x3mm complete with Stainless Steel Tower Bolts, Hinges, Handles, Stops, Lugs, etc. including Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm, guard bars etc., complete all as specified and directed. NOTES :- (a) For the purpose of Measurement and Payment, Double Shutters with Frame shall be considered as ONE UNIT. (b) Unit Rate quoted shall deem to be include all the Stainless Steel Builders & Hardware as required/directed at Site. (c) Quoted Unit Rate shall also deem to be include Mild Steel Guard Bars of 10mm Square Bar, spacing at 10 Cm centre to centre on both Vertical & Horizontal directions. (d) Mosquito proof wire cloth and Sheet Glass shall be Measured and Paid for separately under appropriate Item.

Hacking out old broken Glass (any thickness, size, quality or description) from Metal Frames, glazed with putty or fixed with beads, complete all as specified and directed.

S&F Plain Sheet Glass 4.0mm thick, Ordinary quality and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and directed.

S&F Frosted Sheet Glass 4.0mm thick, Ordinary Type and glazing with Oil Putty in Square not exc. 0.50 Sqm in Each Pane, complete all as specified and directed.

S&F in repairs Stainless Steel Curtain Rod 25mm dia/bore (as approved) including fixing stainless steel Bracket (shaped as approved) not less than 80mm long to wall with Screws/ secured with stainless steel side doom(as approved) fitted/tightened on Curtain Rod at both ends with screw, complete all as specified and as directed. Note : Cost of brackets and end caps shall deemed to be included in the quoted rate.

S&F in repairs 18-19 mm thick PVC Board Scratch and strain free (weight not less 9 Kg/Sqm) in Kitchen Cabinets (shelves, doors etc), one side laminated , jointed by means of PVC Adhesive Solvent and fixed using Self-tapping Aluminium Screws, including providing & fixing of Stainless steel L shaped hinges suitable for PVC Board (minimum of 02 Nos for Each leaf ) to hold cabinet door, Stainless Steel Silver chrome Door Handle 100mm long (01 No for each leaf of shutter), magnetic catcher, etc complete all as specified and directed. NOTE: Quoted unit Rates are inclusive of PVC board, handles, hinges, screws, magnetic catcher etc.

S&F in repair stainless steel Cup and Saucer basket of size (370x485x100mm) and fitted to a telescopic drawer channel and PVC celuka Ply board with smooth movement complete all as specified and directed. Make : Godrej (Product Code : 6129) or equivalent in HETTICH/OZONE/EBCO/HAFFLE

S&F in repair stainless steel Perforated Cutlery basket of size (370x485x100mm) and fitted to a telescopic drawer channel and PVC celuka Ply board with smooth movement, complete all as specified and as directed. Make : Godrej (Product Code : 6132) or equivalent in HETTICH/OZONE/EBCO/HAFFLE

S&F in repair 500 mm telescopic drawer channel fitted to celuka Ply Board and stainless steel basket for smooth movement, complete all as specified and as directed. Make: Godrej (Product Code : 5919) or equivalent in HETTICH/OZONE/EBCO/HAFFLE

M&L for Dismantling Stone Slabs and/or Tiles of any description or thickness in Floors, Aprons, etc. laid, bedded and pointed in Cement Mortar, removal of debris outside AF land, cleaning of area to remove dust, loose particles, washing with water complete all as specified and directed.

M&L for providing Granite (of any type) Tiles, 16-18mm thick, machine cut, bedded and jointed with grey cement slurry and pointed with white cement and admixture of pigment to match the shade of granite stone including edge moulding, grinding and polishing complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

-ditto- but for Granite (of any type) Tiles, 16-18mm thick machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry, and pointed with white cement and admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

M&L for providing Machine cut Pre-Polished Kota Stone Tiles, of any size as directed by Engineer-in-Charge, 18-20mm thick in Flooring, laid and joined with grey cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

-ditto- but for Machine cut Pre-Polished Kota Stone Tiles 18-20mm thick, in Riser of Steps, Skirting, Dado and Pillar, joined with grey Cement slurry mixed with pigment to match the shade of the slab complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

Dismantling Floor, Paver Tiles, Hearth or Wall Tiling, etc. including Cement Mortar Bedding (but not backing) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L for providing non-skid/matt finish Ceramic tiles, coloured, 7-8 mm thick (Square/rectangular), area of each tile exc 0.18 Sqm but not exceeding 0.38 Sqm in Flooring, set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the tiles complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

-ditto- but ceramic tiles of size exc 0.18 Sqm but not exceeding 0.38 Sqm in skirting

M&L for providing non-skid/matt finish Ceramic tiles, coloured, 7-8 mm thick (Square/rectangular), area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm in Flooring, set and jointed in Neat Cement Slurry and pointed in White or Colour Cement to match the tiles complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

M&L for providing Coloured Glazed Ceramic Tiles in vertical surfaces, size 300X600X 7mm thick, set and jointed in neat cement slurry and pointed in white or colour cement to match the Tiles complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

M&L for providing Vitrified Ceramic Tiles, 9-10mm thick (Square/ Rectangular), coloured, Light shade, Polished, area of each Tile exc. 0.42 Square Metre but not exc 1.00 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

-ditto- but for vitrified tiles in skirting, fixed over and including Screed or Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be included in the Quoted Unit Rate.

M&L for providing Vitrified Ceramic Tiles, 9-10mm thick (Square/ Rectangular), coloured, Light shade, Polished, area of each Tile not exc. 0.36 Square Metre in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Tiles, laid over and including 15mm thick Screed or Screed Bed in Cement Mortar 1:4, complete all as specified and as directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

-ditto- but for vitrified tiles in skirting, fixed over and including Screed or Screed Bed 10mm thick in Cement Mortar 1:4, complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

M&L for providing screed bed for fixing of ceramic floor tiles in cement mortar 1:4, 15mm thick complete all as specified and directed

M&L for providing screed bed for fixing of stone floor tiles in cement mortar 1:4, 20mm thick complete all as specified and directed

M&L for providing screed bed for fixing of ceramic/stone tiles in skirting, etc with cement mortar 1:4, 10mm thick complete all as specified and directed

M&L for providing screed bed for fixing of ceramic/stone tiles in dado, etc with cement mortar 1:3, 10mm thick complete all as specified and directed

S&F in repair angle valve, 15 mm bore, chromium plated brass body, concealed type with wall flange fixed to iron pipe complete all as specified and directed.

S&F in repair Chromium plated brass body two way Angular stop cock, concealed type with wall flange fixed to 15 mm bore of Iron pipe, complete all as specified and directed.

S&F in repair chromium plated Hand shower (health faucet), ABS body with 1.2 metre long flexible tube in chrome finish with wall hook complete all as specified and directed.

S&F in repair Jet Spray with Connection Pipe 15mm bore (dia), Brass Chromium Plated and suitable for Wash Down Water Closet Pan (Pedestal Pattern) , complete all as specified and directed.

S&F in repair Vitreous China White Squatting Pan of size 580x440mm, 'Orissa' Pattern with Integral Foot Rests, ‘P’ or ‘S’ Trap, providing Joints between Flush Pipe and Socket of WC Pan, Cones, India Rubber (nozzles of WC Pan) including provision of Lime Concrete Bedding and Making Good to Floor/distrubed surfaces, complete all as specified and directed.

S&F in repair vitreous china floor mounted one piece closet (Pedestal pattern), white including vitreous china valveless syphonic action type flushing cistern with inlet ball valve float, push button, flush pipe incl bracket, P/S trap, PVC soft close seat cover and connecting fittings complete all as specified and directed. (Make : CERA, Model: CHAMP / PARRYWARE, Model: Entice / HINDWARE, Model: FLORA / ASIAN PAINTS, Model: IMMERSE / ESSCO, Cat No: AIS-WHT-101851S220SPPSM )

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, with 'P' or 'S' trap front or back inlet, fixing bolts (except flushing cistern and flush pipe) incl plastic water closet seat cover (white) and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repair Plastic Water Closet Seat and Cover for Water Closet Pan (Pedestal Pattern), White, Closed Pattern with Flat bottom and Cover and Mild Steel Chromium plated or Aluminised Hinging Device and complete all as specified and directed. NOTE: This item shall be measured for replacement of only seat cover on existing EWC.

S&F in repair Plastic seat & cover, white, soft close type, for water closet (of any description) incl chromium plated hinge complete all as specified and directed. NOTE: This item shall be measured for replacement of only seat cover on existing EWC.

S&F in repair 10 ltrs capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and incl with flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and directed.

S&F in repair PVC Connection Pipe 15mm size and 45 Cm in length with Adapter Nuts of PVC, complete all as specified and directed.

S&F in repair PVC Connection Pipe 15mm size and 60 Cm in length with Adapter Nuts of PVC, complete all as specified and directed.

S&F in repair Rotational Moulded Polyethene Water Storage Tank, 1000 Litre Capacity, Cylindrical, Vertical with Closed Top, 3 layered, conforming to IS, hoisted and fixed in Position alongwith GI tank nipple & tank cover complete all as specified and directed.

S&F in repairs Ball Valve 20mm dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe, complete all as specified and directed.

M&L Cleaning and removing all Scales and dirts from the Tank and mouths of circulating Pipes, etc. after draining out Water from the Tank of capacity 250 Litre but not exc. 500 Litre, cleaning the Tank by scrubbing the deposits with Wire Brush, re-fixing Inlet and Outlet Pipes in the Same Position and writing Letters "CLEANED ON DD.MM.YYYY" (i.e. Date of Cleaning of Tank) not exc. 50mm in height, complete all as specified and directed.

M&L Cleaning and removing all Scales and dirts from the Tank and mouths of circulating Pipes, etc. after draining out Water from the Tank of capacity 500 Litre but not exc. 1000 Litre, cleaning the Tank by scrubbing the deposits with Wire Brush, re-fixing Inlet and Outlet Pipes in the Same Position and writing Letters "CLEANED ON DD.MM.YYYY" (i.e. Date of Cleaning of Tank) not exc. 50mm in height, complete all as specified and directed.

S&F in repair PVC (SWR) 75 mm floor trap plain with grating including jointing to waste pipe, fixed in cement concrete 1:2:4 (20 mm graded stone aggregates) complete all as specified and directed.

S&F in repair PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, laid on floor, trench etc complete all as specified and directed.

S&F in repairs PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, laid on floors, trench etc complete all as specified and directed.

S&F in repairs PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, single socketed, in any length with PVC Joints, with or without Ears, fixed to Walls with PVC clips, complete all as specified and directed.

S&F in repair PVC (SWR) 110mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, fixed to Walls with PVC Clips, complete all as specified and directed.

S&F in repair PVC (SWR) 75mm bore (dia), Bend any type, provided with Access Door, etc. and jointing with Solvent Cement, complete all as specified and directed.

S&F in repair PVC (SWR) 110mm bore (dia), Bend any type, provided with Access Door, etc. and jointing with Solvent Cement, complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, with access door complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal, with access door complete all as specified and directed.

S&F in repair 75 mm bore PVC (SWR) junction single (single T) equal or unequal, with access door complete all as specified and directed.

S&F in repairs 110 mm bore PVC (SWR) junction single (single T) equal or unequal, with access door complete all as specified and directed.

S&F in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed

M&L for concrete bed to drain pipes including packing under and completely surrounding pipes with concrete after they are laid and tested in cement concrete 1:3:6 , type C2 (using 40 mm graded aggregates) for 110mm OD PVC SWR pipes complete all as specified and directed. (NOTE: Cost of earthwork shall be deemed to be inluded in quoted rate)

Taking up or down Steel Tubing 15mm bore (dia) with Fittings/ Connections, segregating Serviceable Pipes and Fittings/ Connections and keep in Safe Custody for re-use, complete all as specified and directed.

Taking up or down Steel Tubing 20mm bore (dia) with Fittings/ Connections, segregating Serviceable Pipes and Fittings/ Connections and keep in Safe Custody for re-use, complete all as specified and directed.

S&F Chlorinated Polyethylene Chloride (CPVC) pipes 20 mm outside dia, SDR-11, having thermal stability for hot and cold water supply incl all SDR-11 CPVC plain and brass threaded fittings (such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector etc) fixed/laying walls, ceilings or in floors etc. with suitable size MS clamp of spacing 1.00 mtr etc pipe line complete all as specified & directed.

-ditto- but with 25 mm outer dia size CPVC pipes

S&F in repairs CPVC Ball valve 20mm (outer dia), screwed both Ends for CPVC pipes, complete all as specified and directed.

S&F in repairs CPVC Ball valve 25mm (outer dia), screwed both Ends for CPVC pipes, complete all as specified and directed.

S&F in repair Chromium plated brass body Bib cock with wall flange, short body, fixed to 15 mm bore of Iron pipe complete all as specified and directed.

S&F in repair Chromium plated brass Bib cock with wall flange , fancy type, long body, fixed to 15 mm bore of Iron pipe complete all as specified and directed.

S&F in repair 15mm bore chromium plated two way bib cock with flange, fancy type complete all as specified and directed.

S&F in repair 15mm bore chromium plated brass body single lever central hole basin mixer without popup waste system with 450mm long copper pipe and brass nut, complete all as specified and directed.

S&F in repairs Vitreous China Wash Hand Basin 550mm x 400mm in size, white, Flat Back or Angle Back Type, making good disturbed Surfaces in Cement Mortar 1:3, providing CP waste coupling and PVC waste pipe and connected Items, complete all as specified and directed. (Make of WHB : PARRYWARE, Model: FLAIR / HINDWARE, Model: MARIO / JAQUAR, Model: CONTINENTAL / CERA, Model: CLAIR) (NOTE: Cost of Waste coupling and Waste pipe shall deemed to be included in the quoted rate)

S&F in repair vitreous china, white, counter top wash hand basin, including providing 32 mm dia chromium plated waste coupling and making all necessary connections complete all as specified and directed. (Make of Basin : Hindware, Cat No: 10038 / CERA, Cat No: S2030101 / Parryware, Cat No: C0431) (NOTE: Cost of Waste coupling shall deemed to be included in the quoted rate.)

S&F in repair vitreous china, white, under counter wash hand basin, including providing 32 mm dia chromium plated waste coupling and making all necessary connections complete all as specified and directed. (Make of Basin : Hindware, Cat No: 10049 / CERA, Cat No: S2030104 / JAQUAR, Cat No: CNS-WHT-705 or equivalent model in PARRYWARE) (NOTE: Cost of Waste coupling shall deemed to be included in the quoted rate.)

S&F in repair CP bottle trap with internal portion 32mm size with 190mm long wall connection pipe complete all as specified and directed

S&F in repair Chromium plated brass body Wall mixer, with concealed body, with overhead shower arrangement fixed with 15 mm bore Iron pipe complete all as specified and directed.

S&F in repair Chromium plated brass Wall mixer , concealed type incl concealed body, with both overhead and telephone shower arrangement, fixed with 15 mm bore Iron pipe complete all as specified and directed. NOTE: Telephone shower shall be measured and paid seperately.

S&F in repair fancy type chromium plated telephonic hand shower (ABS Body), multiflow type with flexible tube and hook screwed for iron pipe including frame complete all as specified and directed.

S&F in repair chromium plated brass over head shower rose (100 mm dia) with arm , with 3 flow, fixed to 15mm bore of iron pipe complete all as specified and directed.

S&F in repair chromium plated brass over head rain shower rose, square (minimum 150 mm size), duly fixed from ceilings, single flow, fixed to 15mm bore of iron pipe complete all as specified and directed.

S&F in repairs, chromium plated brass Tubular towel rail, 20mm dia, 600 mm long between flanges including brass chromium plated brackets complete all as specified and directed.

S&F in repair Glass Shelf (Bath Tray), 600 mm long alongwith all accessories complete all as specified and as directed.

S&F in repair Corner Glass Shelf single Decker (Triangular shape) of size 30 Cm, complete all as specified and as directed.

S&F in repairs toilet paper holder, chromium plated, surface type with flap complete all as specified and directed.

S&F in repair Chromium plated brass Towel ring complete all as specified and directed.

S&F in repairs towel rack with lower hangar with hook complete all as specified and directed.

S&F in repair chromium plated tumbler holder with glass tumbler & wall flange complete all as specified and directed.

S&F in repairs soap dish, chromium plated body complete all as specified and directed.

S&F in repair 15mm dia soap dish, square, acrylic body with chromium plated base complete all as specified and directed.

S&F in repair soap dispenser with glass bottle with chromium plated base complete all as specified and directed.

S&F in repair sinks made of stainless steel 1 mm thick in kitchen with plug washers, CP waste coupling, PVC waste pipe and fixing cantilever brackets connecting union to pipe, overall size of sink 24" X 18" X 8" complete all as specified and directed. (NOTE: Cost of CP waste coupling and PVC waste pipe is deemed to be included in the quoted rates)

S&F in repair 15mm bore chromium plated brass body sink mixer, swivel casted spout (wall mounted model), single or dual knobs complete all as specified and directed by Engineer-in-charge

S&F in repair Stainless Steel Plate Rack 75x75x25 Cm in size, made out of Stainless Steel 0.63mm thick with all Internal Fittings and fixing with Brass Chomium Plated Mild Steel Screws, complete all as specified and directed.

S&F in repair Grating 100mm dia in size, Chromium Plated (as approved), complete all as specified and directed.

S&F in repairs for waste coupling chromium plated for sink /wash basin, suitable for 32mm dia waste pipe complete all as specified and directed. (NOTE: This item shall only be measured for replacement in existing sinks, basins etc)

S&F in repair PVC Waste Pipe 32mm bore (dia), 60-75 cm length (as required at Site), complete all as specified and directed. (NOTE: This item shall only be measured for replacement in existing sinks, basins etc)

M&L for built in steel cup board with pressed steel frame of size 75x45x1.25 mm thick with pressed steel shutter 1.00 mm thick (Godrej Pattern) fixed to masonry wall by hold fast made out of 25x3 mm thick flat iron incl MS hanging rod of 10mm dia with bracket fixed on inner side of cup board shutter and on other leaf provision of MS peg set of 03 including spray painting with two coats of synthetic enamel paint over one coat of red oxide primer all around steel surfaces of frame and shutter including taking down old existing wooden cup board shutters and making good disturbed portion of walls in CM(1:4) or PCC 1:2:4, surfaces finished with 1.5 thick wall putty and two coats of acrylic distemper complete all as specified and directed. NOTE: For measurement purpose, only exposed portion from front to be considered.

S&F in repair 19mm thick commercial faced plywood grade BWR type B-B fixed with screws to timber frame work as in cupboard shelves & partitions, pelmet boxes, etc complete all as specified and directed.

M&L for 2nd class harwood beadings,19mm wide & 3-4 mm thick, made to shape and fixed with countersunk screws to the edges of plywood shelves, partitons etc, holes filled with putty and surfaces finished with varnish complete all as specified and directed.

Demolition Cement Concrete (un-reinforced) of any description and in any position and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L Cement Concrete 1:5:10, type E-2 (40mm graded stone aggregate) as in mass concrete, sunken floor filling,etc. complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description in rafters, purlins and wind ties wtc and removal from site complete all as specified and directed.

M&L for Mild steel framed works such as grills, gratings etc. with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tanks and similar works conforming to Fe-290 Gde E-165 complete all as specified and directed.

Removing vegetation growth/shrubs (girth up to 30 CM), cutting in brick wall/concrete surface upto triple storey building carefully without damaging the existing soil, vent, water supply pipe and removing roots of plants completely and filling the gaps with PCC 1:2:4, Type B-0 finished with existing surface including all scaffolding ladder etc as required surface are n.exc. 0.36 Sqm each complete all as specified and directed.

M&L applying Flexible Water Proofing & Protective coating on Floor and Walls of Sunken portion as per IS- 2645 and application as per manufacturers instructions comprising with the following, complete all directed by Engr-in-Charge/GE :- (a) Cleaning of surfaces properly to remove all moss, algae, loose particles, oil, laitance, dust etc. All cracks shall be cut in 'V' grooves and shall be filled with latex solution. (Make:- Asian Paint latex/Sika latex SBR 100 putty/ Dr fixit 302 SBR latex/ FOSROC Nitobond SBR Latex) (b) The joints of sunken slab & walls shall be filled with suitable epoxy sealent . (c) Providing 15 mm thick PCC 1:1½:3 type A0 (12.5 mm graded stone aggregates) in floors & fillets at corners. Top surface of the PCC shall be finished with cross slope directed towards the spout. (d) GI pipe of 40 mm medium grade to be inserted at the lateral slope projection at least 25 cm beyond the outer most projected part of the building below the drain pipe. contd.....

Item No 167 (contd....) (e) Watering the concrete surface for proper curing and removing all excess water to leave just a damp surface. (f) Applying Two Coats of two component polymer modified cementitious waterproofing coating @ 1.50 KILOGRAM PER SQM Each Coat (or as recommended by manufacturer) on plastered/concrete surfaces. The Second Coat shall be applied in crosswise direction when the First Coat is completely dried and after a gap of minimum 01 hour. (MAKE: DR FIXIT, PIDIFIN 2K / SIKA, SikaTop®-107 Seal IN /FOSROC, Brush Bond or similar item in other approved makes) (f) A protection plaster 12 mm thick in CM 1:3 mixed with appropriate admixture shall be applied on vertical surfaces as per manufacturers instructions. (Make: SIKA, PLASTOCRETE/FOSROC, CONPLAST WL/DR FIXIT, PIDIPROOF LW+ or similar item in other approved makes) (G) Curing of waterproof coating for a minimum period of 24 hours using watering, wet hessian cloth etc directed by Engineer-in-Charge. NOTE:- Measurement for payment shall be considered for the flat horizontal surface area of the sunken portion of floors.

M&L Repairing of broken/damaged portions of Ceilings, upto any height, adhering proper safety precaution and including necessary preparation i.e. scrapping, cutting, chiseling, removing all loose concrete and cleaning exposed reinforcement with wire brush and applying one coat of cement slurry and filling the surfaces with min 15mm thick Cement Concrete 1:1½:3 (12.5mm graded stone aggregate), finished with 5mm thick rendering in cement mortar 1:3 and surfaces finished to match with existing surfaces including finishing with three coats of white wash complete all as specified and directed. NOTES : 1) Site for application is at various locations in patches with varying heights upto 4m. Contractor's quoted rate shall deemed to be inclusive of the ibid aspect. NO claim shall be entertained during currency of work. 2) Cost of Formwork/Prop, scaffolding, safety gear shall be deemed to be included in the Quoted Unit Rate.

M&L Repairing of broken/damaged portions of RCC Projection, Chajjas, Roofs Facia, Column, etc. upto any height adhering proper safety precaution and including necessary preparation i.e. scrapping, cutting, chiseling, removing all loose concrete and cleaning exposed reinforcement with wire brush, removing all dust & debris, cleaning with water and and applying one coat of cement slurry and filling the surfaces with min 25mm thick Cement Concrete 1:1½:3 (12.5mm graded stone aggregate) duly reinforced witth GI wire netting, surfaces finished to match with existing surfaces including providing a Coat of Chalk Whiting and finishing with Two Coats of Exterior Emulsion Paint over a coat of exterior cement primer with approved Tint as per manufacturer's instructions, complete all as specified and directed. NOTES : 1) Site for application is at various locations in patches with varying heights upto 12m. Contractor's quoted rate shall deemed to be inclusive of the ibid aspect. NO claim shall be entertained during currency of work. 2) Cost of Formwork/Prop, scaffolding, safety gear shall be deemed to be included in the Quoted Unit Rate. 3) Wire netting shall be paid seperately as "Supply Only"

Supply only wire netting of stainless steel wire, 1.4mm dia, with mesh size 12mm complete all as specified and directed.

Demolition Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level) and removing debris, etc. to Outside MD/AF Land, complete all as specified and directed.

M&L for Cement Concrete 1:3:6 type C1 (20mm graded stone aggregate) 75mm thick as in Plinth Protection, finishing Cement Concrete surface Even and Smooth without using Extra Cement, including making joints 12mm wide upto total depth of concrete at every 3.00 metre interval and every change of direction and filling with bitumen mastic complete all as specified & directed.

M&L Cement Concrete 1:3:6 type C1 (20mm graded stone aggregate), 100mm thick, as in floor, path, hardstanding etc, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for providing outdoor type heavy duty ceramic Floor (Paver) Tiles, 300 x 300 x 9-10mm thick, Anti-skid type, Impact Resistant, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete all as specified and directed. NOTE : Cement Screed Bed shall be measured and paid seperately.

M&L for Cement Concrete 1:2:4 type B1 (20mm graded stone aggregate) as in Coping, Bed Plates, Holdfast, Bed Block, Kerb Stones including necessary Formwork and weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed.

Taking down damaged/unserviceable Aluminiumm Chowkat or Frame exc. 1.50 Sqm but not exc. 4.00 Sqm Each with shutter( without taking off shutter from the frame) and removal from site complete all as specified and directed.

Taking down damaged/unserviceable Aluminium Chowkat or Frame not exc. 1.50 Sqm Each with shutter (without taking off shutter from the frame) and removal from site complete all as specified and directed.

Taking down aluminium Shutter of any description, area exc 1.00 Sqm and not exc. 2.00 Sqm Each and Refixing in the Same Opening, after resecuring or easing and adjusting, etc. including re-fixing of glass sheet and replacement of necessary Jointing Cleats, Glazing Clips, Rubber Neoprene Packing, Screws, etc. and repairing of Locking Arrangement if any, complete all as specified and directed. NOTE : Cost of Materials required for smooth functioning of Shutter shall deem to be included in the Quoted Unit Rate. Locks and glass sheet, if required to be replaced shall be measured seperately under respective items.

S&F powder coated (medium thickness of powder coating 50 micron) anodised aluminium frame for door, windows, partitions and ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, anodised aluminum fittings such as suitable 150 mm long peg stays (01 No), hinges type B-21 100 mm long (02 Nos), suitable handle - 01No each shutter etc as per manufactures instruction complete all as specified and directed. (NOTE: Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle etc as described in item. Sheet glass shall be measured seperately)

S&F powder coated (minimum thickness of powder coating 50 micron) anodised aluminium doors shutters, aluminium section weighing 0.55 Kg/metre including necessary jointing cleats, glazing clips rubber packing handle 2 Nos in each door, hinges, Mortise lock vertical type size 100 mm 4 levers of brass in each door, anodised aluminium snap beading screws etc as per manufactures instruction complete all as specified and directed. (NOTE:- Quoted rate is deemed to be inclusive of the cost of include for anodised aluminium hard ware as indicated, glazing clips, rubber packing, anodised aluminium snap on beading for fixing glass panes in frames, handle, Mortice Lock etc as described in item. Sheet glass shall be measured seperately)

S&F powder coated aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in- charge.

S&F in repair Mild Steel Mortice Lock 100mm in size, 4-Lever, Vertical type, complete all as specified and directed.

S&F in repair Double Action Floor Spring Hydraulically Regulated made up of minimum 1.25mm thick Aluminium alloy Sheet Foundation Box, Main Body with Stainless Steel Cover, Governing Pivot made of Brass, Other Parts made of Mild Steel heavy duty complete all as specified and as directed.

S&F in repair Door Closer Aluminium (Die cast) body, hydraulically regulated, Designation No. 3, Universal type, suitable for Door Shutters of 851mm to 1000mm in width and of weight between 61.00 to 80.00 Kilogram complete all as specified and directed.

S&F Sheet Glass 5.50 mm thick, Tinted (as approved by GE), fixed to Aluminium Windows of size exc 0.50 sqm each pane complete all as specified and directed.

S&F Sheet Glass 4.80 mm thick, Tinted (as approved by GE), fixed to Aluminium Windows of size exc 0.50 sqm each pane complete all as specified and directed.

S&F in repair stainless steel peg set of five, best quality complete all as specified and as directed.

Dismantling of ceiling board incl snap grid frame of any thickness including cover fillets complete all as specified and directed.

Dismantling of wall board as in lining, panelling etc, of any gauge or any thickness including cover fillets complete all as specified and directed.

S&F Suspended metal grid Ceiling System with mineral fibre acoustic tiles as per following specifications:- a) Ceiling Tiles:- Mineral fibre acoustic tile of 16mm thickness having sand textured finish with acoustical punchers, bevelled tegular edge and 8mm drop in module size of 600 x 600mm. Tiles shall have humidity reistance (RH) of 99%, NRC 0.50 (Average value of Absorption Co-efficient readings taken at 250 Hz, 500 Hz, 1000 Hz and 2000 Hz) as per ASTM C423 standard, CAC of 33db as per ASTM E1414, Light Reflectance ≥85% as per ASTM E-1477, Thermal Conductivity k = 0.052 - 0.057 W/mK, Colour Global White, Fire Performance of class 0/1 as per BS 476 Part 6/7 and Class A as per ASTM E84. b) Metal Grid:- The grid system shall be 15 mm wide T - section flanges colour global white (matching to tile color) having roll formed double stroke rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 38mm (all sections). The deflection loading of the system shall be 12.5 kg/m2 (as per standard installation layout mentioned below) and main beam tested as per ASTM C635 (Deflection limit less than L/360) with a deflection loading of 15kg/m. The end details of the cross tee shall be made of pre hardened steel and fixed to the ends of the cross tee to provide double locking between “cross tee to cross tee” and “cross tee to main beam”. Contd......

Item No 191 (contd....) All main beam to main beam and cross tee to cross tee connection shall have a pull out strength of more than 100kg. The T Sections shall be made of hot dipped galvanized steel of 90 gsm as per IS 277 (2003) and pre-painted steel with baked polyester paint with 0T bending capability. The ceiling grid sections shall be fixed to ceiling with 6 mm dia GI hangers upto required length by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5mm dia 40 mm long. (MAKE OF CEILING GRID : ARMSTRONG, Model: SUPRAFINE or equivalent in GYPROC / USG BORAL / UNISTEEL MAKE OF CEILING TILES: ARMSTRONG, Model: DUNE or equivalent item in GYPROC / USG BORAL / U TONE)

S&F wall panelling with hollow 5 mm thick PVC panels of 10"/12" width and any height, single side pre-laminated with flat or fancy patterned on laminated side, fixing on walls with screws or with solvent cement as required on site including necessary corner angles, fillets etc as required at site complete all as specified and directed.

M/S GOYAL CONSTRUCTIONS (BID ID -3311946)

M/s Satguru Traders (BID ID -3312069)

M/s Shree Bala Ji Construction Company (BID ID -3312345)

shiv shanker enterprises (BID ID -3308151)