Construction of CCP Office Building on Plot bearing P.T. Sheet no. 43 Chalta no. 111,112,132A to 132K at Panaji for Corporation of the City of Panaji

Amount

Earthwork in excavation by mechanical means (hydraulic excavator)/ manual means over areas for all leads & lifts in all types of strata comprising of any type of materials either in full or part as the case may be adopting any method/methods as may be convenient as permitted excluding blasting in all conditions such as dry, moist, foul, saturated, submerged etc. including dressing of sides, planking and strutting, timbering, ramming of bottom, pumping and bailing out water, barricading, danger lighting, guarding and carting away excess excavated earth at the site identified by the contractor and obtaining all statuatory approvals, as directed by engineer for all leads and lifts etc complete.

Earthwork in excavation by mechanical means (hydraulic excavator)/ manual means in foundation/pipeline trenches drains for all leads & lifts in all types of strata comprising of any type of material either in full or part as the case may be adapting any method/methods as may be convenient as permitted excluding blasting in all conditions such as dry, moist, foul, saturated, submerged etc. including dressing of sides, planking and strutting, timbering, ramming of bottom, pumping and bailing out water, barricading, danger lighting, guarding and carting away excess excavated earth at the site indentified by the contractor and obtaining all statuatary approvals, as directed by engineer for all leads and lifts etc complete.

Refilling the pipeline/foundation trenches plinth sides, foundation etc. with available excavated earth in layers not exceeding 20 cm depth consolidating each layer ramming and watering lead upto 50 M and all lifts and disposal of surplus earth as directed by Engineer.

Disposal of surplus earth & debris upto 10 KM lead including loading, unloading and stacking, The site should be identified by the contractor and obtain all statuatory approval.

Providing & Constructing Half brick masonry using fly ash bricks in cement mortar 1:3 (1 cement: 3 coarse sand) with bricks of class designation 40 kgs / cm2. in foundation and plinth 200x95x95 / 230x110x80

Providing & Constructing Half brick masonry using fly ash bricks in cement mortar 1:3 (1 cement: 3 coarse sand) with bricks of class designation 40 kgs / cm2. at all levels 200x95x95 / 230x110x80

Providing & laying rubble packing with hard laterite stone under floors including watering ramming and consolidating etc.in pipeline trenches and other foundations complete.

Providing & constructing laterite masonary in neatly dressed stones of size as specified in Cement mortar 1:5 (1cement : 5coarse sand) in foundation and basement.

Exposed decorative laterite masonry using Patradevi stone of size as specified and laid as directed by architect in cement mortar 1:4 (1 cement : 4 coarse sand)

Providing & constructing laterite masonary in neatly dressed stones for 23 cms masonary walls in c.m 1:4 (1 cement : 4 coarse sand) in super structure at all levels

Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in: all works upto plinth level

Providing and laying upto floor V level cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including smooth finishing to exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc. a) Kerbs, Steps and the like at or near ground level

Providing and laying upto floor V level cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including smooth finishing to exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc.b) String Courses, copings, bed plates, anchor blocks, plain window sills and the like

Providing and laying upto floor V level cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggregate 20 mm nominal size) including smooth finishing to exposed surfaces, with cement mortar 1:3 (1 cement: 3 fine sand) including centering and shuttering etc.c) Small lintels not exceeding 1.5 m clear span including coping and the like requiring formwork to the suspended portions

Centering and shuttering including strutting, propping etc. and removal of forms for a) foundation, footings, bases of columns etc.

Centering and shuttering including strutting, propping etc. and removal of forms for b) Vertical surfaces such as retaining walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like

Centering and shuttering including strutting, propping etc. and removal of forms for c) Columns, Piers, Pillars, Abutments, Posts and struts (square, rectangle polygon in plan) at all levels

Centering and shuttering including strutting, propping etc. and removal of forms for d) Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth at all levels

Centering and shuttering including strutting, propping etc. and removal of forms for e) Staircases (Except Spiral Staircases) excluding landings

Centering and shuttering including strutting, propping etc. and removal of forms for f) suspended floors, roofs, landings, shelves and their supports, balconies and chajjas at all levels

Centering and shuttering including strutting, propping etc. and removal of forms for g) Vertical or horizontal fins individually or forming box, louvers or projected bands at all levels

Centering & shuttering including Strutting, Propping & removal of forms for sloping or battering surface (slabs, beams, louvers, etc) including folded plates a) Where inclination to the horizontal does not exceed 30° requiring shuttering on the underside only

Providing TMT steel reinforcement bars of SAIL, TATA. VIZAG JSW Steel Ltd.) make only (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member.

Extra for rendering smooth the top of the suspended floors, landing and staircase (treads and risers) with cement mortar 1:2 (1 cement: 2 coarse sand) including a floating coat of neat cement and protecting the surface with a layer if 7.5 cms of earth laid over 15mm layer of fine sand in case of suspended floor and bricks laid in mud mortar in landing of steps including subsequent removal and cleaning of the same

Providing and laying in position machine batched concrete (BMC), machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to the site of laying but excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing the strength and durability as per the direction of the Engineer. M35 grade of reinforced cement conrete by using 400 kg of cement per cu.m. of concrete. All works at all floor levels. NOTE:- Use of RMC is permitted at no extra cost

Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification. - 60cm L x 30cm H x 10cm T

Supplying and fixing of Precast RCC slabs(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) at site in concrete Grade of M-25 with 20 mm nominal size Granitic or basaltic aggregate, consolidated by means of mechanical platform, vibration etc. with lifting hooks of M.s. 10mm bars and PVC cups including cost of reincforcement, Certificate from manufacturer shall be produced indicating grade of concrete and minimum content of steel in the product along with 5 year free replacement warranty in case of breakage complete and as directed by Engineer -in -charge. a) Size 900 x 400 x150 mm with steel reinforcement not less than 7.0 kg per unit - 30T Capacity

Supplying and fixing of Precast RCC slabs(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) at site in concrete Grade of M-25 with 20 mm nominal size Granitic or basaltic aggregate, consolidated by means of mechanical platform, vibration etc. with lifting hooks of M.s. 10mm bars and PVC cups including cost of reincforcement, Certificate from manufacturer shall be produced indicating grade of concrete and minimum content of steel in the product along with 5 year free replacement warranty in case of breakage complete and as directed by Engineer -in -charge. b) Size 750 x 400 x100 mm with steel reinforcement not less than 4.2 kg per unit

Add for using more cement that the quantity as provided in batch mix concrete as arrived as per the mix design

Providing and fixing wood work in frames of doors, windows, clerestory windows, trusses & other frames wrought framed and fixed in position Second class Indian Teak wood as per drawing

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type (BWP), core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing vision panel not exceeding 0.1 sq.m. in all types of flush doors - Rectangular or square Unit: SQ.M. door area as per drawing including glass of approved make

Providing and fixing second class Indian Teak wood moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surfaces etc. - 50 x 12 mm

Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastner of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer. - 10 x 120mm

Providing and fixing MS grill of required pattern in wooden frames of windows, masonry etc with MS flats, square or round bars with round headed bolts and nuts or by screws - Plain Grill as per drawing

Providing bright finished stainless steel parliamentary hinges 100x100x27mmx5mm with necessary screws etc complete instead of providing Stainless steel Butt Hinges 100x60x2.5 (Only difference in rate to be quoted)

Providing and fixing SS 304 Aldrop/ sliding door bolts with bolts, nuts and screws etc complete - 250 x 16 mm

Providing and fixing SS 304 Tower bolts (Barrel type) with necessary screws etc complete - 250x10 mm

Providing and fixing SS 304 Tower bolts (Barrel type) with necessary screws etc complete - 100x10 mm

Providing and fixing bright finished SS 304 handles with necessary screws etc complete - 125mm

Providing and fixing bright finished C. P. Brass/brass door latch with necessary screws etc complete - 250 x 16 x 5 mm

Providing & fixing Stainless Steel tubular lever D-Type mortise handles with round/Square nose, 24mm Mortise/sash lock body & Strike plate (all SS Finish), Pin cylinder 60mm with one side key and other side knob/thumb turn with necessary screws etc. complete

Providing & fixing bright finished C. P. Brass/brass 100 mm. rim latch & lock & a pair of knob, with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing 150 mm. SS 304 floor door stopper with rubber cushion screws etc. to suit shutter thickness complete.

Providing and fixing brass hydraulic door closer with necessary screws and fittings complete.

Providing & fixing Stainless Steel Cylindrical lock 60mm dia with pair of knob, keys etc. with necessary screws etc. for doors complete as approved by engineer. Entrance Function: Internal Push Button & External Key Operation

Providing and fixing Stainless steel D type handles with necessary screws etc complete a) L 300mm/325mm x 22 to 25mm dia

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) in built up sections trusses and framed work including cutting, hoisting, fixing, in position and applying priming coat of red lead paint. a) In Tees angles flats and channels

Providing and Fixing M. S. round holding down bolts with nuts and washer plates complete.

Providing & fixing bolts with nuts & washer complete. (Hi Tensile black bolts & nuts as per approved make)

Providing & fixing Anodised Aluminium shutters in accordance with the specifications annexed with Goa schedule of rates (2004) Vol I & II including all taxes, transportation, scaffolding and handling etc Complete as per direction of the engineer : Windows with two sliding shutters using 18mm series shutters sections with plain glass including powder coating with pure polyester of required shade and colour. All work between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant Rectangular Tube @1.139Kg/m 100x40x1.50, 3 Track Top & side @0.848Kg/m 91.8x31.75x1.20, 3 Track Bottom @0.98Kg/m 91.8x31.75x1.20, Shutter Handle @0.431Kg/m 39.4x17.7x1.20, Shutter Interlock @0.51Kg/m 39.4x17.7x1.20, Shutter Top & Bottom @0.42Kg/m 39.4x17.7x1.20, 4 mm thk clear float glass, EPDM gaskets complete with accessories for locking, handles, stopppers, ball bearing etc.

Providing & fixing Anodised Aluminium shutters in accordance with the specifications annexed with Goa schedule of rates (2004) Vol I & II including all taxes, transportation, scaffolding and handling etc Complete as per direction of the engineer : Windows with three sliding shutters using 18mm series shutters sections with plain glass including powder coating with pure polyester of required shade and colour. All work between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant. Rectangular Tube @1.139Kg/m 100x40x1.50, 3 Track Top & side @0.848Kg/m 91.8x31.75x1.20, 3 Track Bottom @0.98Kg/m 91.8x31.75x1.20, Shutter Handle @0.431Kg/m 39.4x17.7x1.20, Shutter Interlock @0.51Kg/m 39.4x17.7x1.20, Shutter Top & Bottom @0.42Kg/m 39.4x17.7x1.20, 4 mm thk clear float glass, EPDM gaskets complete with accessories for locking, handles, stopppers, ball bearing etc.

Providing and fixing Anodized Aluminium shutters in accordance with the specification annexed with Goa schedule of Rates (2004) Vol & II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer : adjustable louvred windows (louvre blades of thickness 1.20mm) with figured glass including powder coating with pure polyester of required shade and colour. All work between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant Rectangular tube @0.478kg/m 50.8x25.4x1.20 U Channel top & bottom @0.073kg/m 9.52x9.52x1.10 4 mm thk figured glass, EPDM gaskets complete with accessories for locking, handles, stopppers etc.

Providing & fixing Anodised Aluminium shutters in accordance with the specifications annexed with Goa schedule of rates (2004) Vol I & II including all taxes, transportation, scaffolding and handling etc Complete as per direction of the engineer : Fixed Window/ ventilators matching with 18mm series shutters sections with plain glass including powder coating with pure polyester of required shade and colour. All work between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant Rectangular Tube with S/G @0.692Kg/m (63.50x38.10x1.15), D/G @0.724Kg/m (63.50x38.10x1.15), glazing clip @0.104kg/m 19.12x16.82x0.90 4 mm thk clear float glass, EPDM gaskets complete with accessories for locking, handles, stoppers, ball bearing etc.

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.with hairline finish, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Supply and installation of Aluminium Louvers. The frame should be made of Aluminium tubes of size 100x50X1.50 mm thk and 50X25x1.50 mm thk C channels. Aluminium Z shaped louvers of 100mm should be fixed to the supporting frame with aluminium cleats, GI screws, etc complete. The whole assembly is powder coated with pure polyester paint. (MS framing to be paid separately)

Ultra-high strength, high-precision, dual shrinkage compensated, free flow cementitious grout for machine , column base plates. Providing and Supplying Masterflow 928T of BASF make or equivalent approved which is dual shrinkage-compensated, cementitious grout shall be hydraulic-cement based free-flow, high strength grout that complies with ASTM C1107. The grout shall have compressive strength minimum of 35 MPa at 1 day and 75 MPa at 28 days; flexure strength minimum of 9 MPa at 28 days. The grout must exhibit positive volumetric expansion in plastic stage as well as hardening stage. Grout must be flowable at 0.15 w/c ratio and shall have fresh wet density in excess of 2200 Kg/m3. The grout must be accredited by reputed testing institute for dynamic load resistance test of 2 million cycles with no sign of cracking or strength loss. All scaffolding, ladders, supporting materials etc. complete. Rates shall be inclusive of all labour, materials, tools and plant etc. complete.

Proving & laying 25mm Cement concrete flooring 1:2:4 (1cement :2coarse sand:4 graded stone aggregate 12.5mm nominal size) finished with a floating coat of neat cement

Kotah stone slab flooring over 25 mm thick in risers of steps, skirtings, dado & pillars laid on 12mm (average) thick cement mortor 1:3 (1 cement : 3 coarse sand) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishingcomplete. (Quality of stone to be conforming to the price range between Rs.592-650 per sq. mt)

Rounding of edges of marble/ Granite / Kotah slab to semi circular slope

Providing and laying jet black mirror polish granite flooring and dado over 20mm thick base of cement mortar 1:4 laid over and jointed with cement slurry including rubbling complete Granitic slab (jet blck with mirror polish) 20 mm thick (Quality of stone to be conforming to the price range between Rs.1991-2000 per sq. mt)

Providing and laying jet black mirror polish granite in urinal partitions with cement Complete. 20mm one side polished should be joined together with two component epoxy adhesive to make 20+20mm = 40mm thk partition (Quality of stone to be conforming to the price range between Rs.1991-2100 per sq. mt)

Providing and laying 20mm thick cuddapah in shelves over 20 mm thick base of cement mortar 1:3 complete (Quality of stone to be conforming to the price range between Rs.323-400 per sq. mt)

Providing & laying 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer (Quality of stone to be conforming to the price range between Rs.323-400 per sq. mt)

Providing and fixing Kota stone tread tiles 35mm thick in single piece with rounded of nosing antiskid groove laid on and including 20mm (average ) thk bed of cement slurry including pointing with pigmented cement slurry to match the shade of the slab, cleaning etc. complete.

Providing & laying 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados jointing with cement based high polymer modified quick-set tile adhesive (water based) conforming to IS:15477, using 5 kg. adhesive per sq.m of tile area, in average 3 mm thickness, including pointing in white cement mixed with pigment of matching shade complete. - Wall Ceramic Glazed Tiles : 300 x 450 (Quality of tile to be conforming to the price range between Rs. 466-500 per sq. mt)

Providing & laying 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados jointing with cement based high polymer modified quick-set tile adhesive (water based) conforming to IS:15477, using 5 kg. adhesive per sq.m of tile area, in average 3 mm thickness, including pointing in white cement mixed with pigment of matching shade complete. - Wall Ceramic Glazed Tiles : 300 x 600 (Quality of tile to be conforming to the price range between Rs. 550-600 per sq. mt)

Providing and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete - Light Shades (Quality of tile to be conforming to the price range between Rs. 313-350 per sq. mt)

Providing and laying vitrified floor tiles in different sizes of (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete. - 600 x 600 mm light Shades (Quality of tile to be conforming to the price range between Rs. 551-600 per sq. mt)

Providing and laying vitrified industrial floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete a) 300 x 300 mm Light Shades - 10 mm thick (Quality of tile to be conforming to the price range between Rs. 500-550 per sq. mt)

Providing and laying vitrified unglazed porcelain tactile floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete a) 300x300 Design - Liner/ Button (Quality of tile to be conforming to the price range between Rs. 1100-1200 per sq. mt)

Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. 60 mm thick in all colours except grey (Quality of tile to be conforming to the price range between Rs. 1085-1200 per sq. mt)

Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with cement based high polymer modified quick-set tile adhesive (water based) conforming to IS:15477, using 5 kg. adhesive per sq.m of tile area, in average 3 mm thickness, including pointing/grouting in white cement mixed with pigment of matching shade complete. - 600x600 mm - light Shades (Quality of tile to be conforming to the price range between Rs. 551-600 per sq. mt)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm a) Jet Black (Quality of stone to be conforming to the price range between Rs.1991-2100 per sq. mt)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for Flooring, kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm a) Elite Brown (Quality of stone to be conforming to the price range between Rs.1668-1750 per sq. mt)

Jaisalmer stone flooring/dado with 18mm thick polished Jaisalmer stone over 20mm (average) thick base of CM 1:4 (1 cement : 4 Coarse sand) with joints finished flush (Quality of stone to be conforming to the price range between Rs.915-1100 per sq. mt)

Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete a) Elite Brown (Quality of stone to be conforming to the price range between Rs.1668-1750 per sq. mt)

Providing water proofing treatment over the new RCC roofs, terrace, sunken slabs, chajjas by spreading cement slurry over the RCC slab and laying of 100 mm average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba should be covered with damp proof of Hindustan water proofing co. Or equivalent, joint less water proofing plaster of mix 1:3 (1 cement : 3 Fine sand), finish smooth with wooden trowel with false marking of 30cm squares. the Vertical surfaces of the adjoining walls are to be treated upto a height of 30cms including rounding of junctions (The rate includes for complete items including labour and materials and including the cost of initial treatment of roof slab as follows. The injection of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb cracks etc. in the RCC slabs) Note: The cement consumption 25 kg /sq.m.

An elastomeric, cementitious, waterproof coating for concrete and masonry. Providing and applying on a well prepared vertical / Horizontal surface Masterseal 550EL of BASF make or equivalent elastomeric flexible, two component polymers modified cementitious composite system that requires no addition of water at the site. The product shall be applied in minimum two coats to achieve total DFT of 1mm. The material shall be mixed and applied fully in accordance with the manufacturer's instructions. The product shall exhibit at least 40% elongation at ambient & 30% elongation in under water condition with tensile strength greater then 20 Kg/cm2. The product shall resist 1.5 bars pressure when tested as per DIN 1048 at 2mm DFT. When applied at 2mm DFT, elastomeric coating shall be able to bridge crack up to 0.5mm width. All scaffolding, ladders, supporting materials etc. complete. Rates shall be inclusive of all labour, materials, tools and plant etc. complete.

Providing & Fixing in position Double Skin roof with Zincalume/ Galvalume colour coated & bare profile sheet with subtle square fluting factory cut at all heights for roof, side & Gable cladding complete in all respect. TOP SHEET-The end rib shall be designed for anti-capillary action. The feed material should be manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc &1.5% Si) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with quality paint coat as per AS/NZS 2728 type 3-4. The paint shall have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior SMP coat on top surface and nominal 5 μm reverse backer coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade. Total Coated Thickness (TCT) should be 0.50mm. Total Painted Thickness (TPT) should be in addition to 0.50mm. The steel sheet shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturers recommendations.The profile sheet, fastener size etc. shall be approved by the Engineer. The sheeting should be with minimum 200mm lap & waterproof with Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed Z-Sub Girt - roll formed section 50x50x50x1.50 TCT, 120GSM Galvanised, High Strength (345 MPa), approximate Wt. 1.85 kg/r.m. fixed with self tapping screws Glass Wool Insulation with FSK facing 50mm with 24 kg/m3 density in between 2 sheets. LINER SHEET-bare galvalume/zincalume roofing sheet of same profile as top sheet. The feed material is of manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.47 mm TCT), Histrength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides), passivated & resin coated. The feed material should have coil manufacturer’s product details marked at regular interval for confirming genuinity of the material. complete as per the directions of the engineer. The steel manufacturer's test certificate for the chemical & mechanical properties of steel must be submitted for approval prior to installation.

Providing & fixing in position Galvalume/Zincalume flashings, cappings, ridges, gutters upto 600mm/610mm girth and min 3.00m in length (cold Rolled Steel 550 MPa yeild Stress ASTM A 446 Grade E) with hot-dip metallic coating of aluminium-zinc alloy(AZ 150 galvalume) (150 gms/sqm total of both sides with Al-Zn Composition= 55% & 43.5% resp. & 1.5% Si conforming to ASTM 792/ AS 1397) 0.45 mm base metal thickness and 0.50mm total coated thickness, factory cut at all heights for roof, side & gable cladding complete in all respects with AZ 150 GSM SMP color Coated (20mic exterior coat of Silicon Modified Polyester paint system over 5 mic primer and 5 mic polyester back coat over 5 mic primer) incl. fixing to purlins with no 12x14x55mm mechanically galvanised hex head self drilling screws of the best quality as per AS-3566 class 3-4 approved, which should be compatible to be used with sheets. with integral washers and EPDM seals etc. Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed.

Providing & fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length & of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24/15x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm & wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27x37x25/15x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85x30x0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24/15 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer. a) GI Metal Ceiling Lay in plain Tegular/ Bevelled edge Global white color tiles of size 595x595 mm, & 0.4-0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) & electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

b) GI Metal Ceiling Lay in perforated Tegular/ Bevelled edge global white color tiles of size 595x595 mm and 0.4-0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Providing and laying integral cement based treatment (Box type) for water.proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer and consisting of : i) Ist layer of 20 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer using rough Shahbad/Kotah stone

Providing and laying integral cement based treatment (Box type) for water proofing on the vertical surface by fixing specified stone slab 20 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer using rough Shahbad/Kotah stone.

Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge.

Providing and Fixing M/F suspended ceiling (Single Layer) which includes providing & fixing GI perimeter channels of size 0.55mm thk having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brickwall/partition with the help of nylon sleeves and screws, at 610mm centres. Then suspending GI intermediate channels of size 45mm, 0.9mm thk with two flanges of 15mm each from the soffit at 1220mm centres with ceiling angle of width 25mmx10mmx0.55mm fixed to soffit with GI cleat and steel expansion fastners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 457 mm centres. 8mm tapered edge Calcium Silicate Board is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, Joint paper tape and 2 coats of Drywall topcoat Suitable for Calcium Silicate board, complete in all respects.

Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

12mm cement plaster 1:4 (1cement: 4 fine sand)

6mm cement plaster to ceiling 1:4 (1 cement : 4 fine sand)

neat cement punning

Extra for providing and mixing water proofing material proportion recommended by the manufacturers. a)12mm cement plaster 1:4 (1 cement : 4 sand)

18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge including providing and mixing water proofing material proportion recommended by the manufacturers at all height from ground level

12mm thick molded cement mortar bands in cement mortar 1:4 (1 cement : 4 fine sand) cm per meter

White washing with lime on new work (three or more coats) to give an even shade

Applying priming coat with ready mixed primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat ) with superior quality ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give a even shade

Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for wood work of approved brand & manufacture in all shades on new work to give an even shade.

Painting(two or more coats) with synthetic enamel paint of approved brand and manufacture in all shades on new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade

Painting (one or more coats) with black japan paint of approved brand and manufacture to give an even shade.

Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade (including min two priming coats and two layers of putty alternatively)

Varnishing (two or more coats) with copal varnish of approved brand and manufacture on new work including an under coat Bees waxing on wood work with local made wax polish in proportion of 2:1 5:1 0.5 (2 wax: 1.5 linseed oil - With transparent wood filler.

Painting three or more coats with acryllic exterior paint of approved brand and manufacture (such as weather shield, Apex) including applying one coat of cement primer and one coat of surface treatment etc. complete, At all heights from ground level

Melamine polishing on wood work (one or more coat) a) Matt

Applying breathable, non-reactive, antifungal, and water repellant Silane/ Siloxane chemical as approved by Archaeological Survey of India/ Engineer, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the exposed laterite masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer. (The rate is inclusive of all materials & labours).

Supplying and stacking of good earth at site including royalty and carriage upto 1km (earth measured in stacks will be reduced by 20% for payment) including Spreading of Sludge Farm Yard Manure or/and good Earth in required thickness (cost of sludge, farmyard manure or/and good earth to be paid for separately)

Turfing lawns with fine grassing including ploughning, dressing including breaking of clods, removal of rubbish, dressing and supplying doob grass roots at 10 cm apart including supplying and spreading of farmyard manure at rate of 0.6 cum per 100 sqm as per MORT&H Specification 307 including Maintenance of lawns with fine grassing for the first year including watering, etc.as per MORTH Specification 307

Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metre and supplying and planting hedge plants at 30 cm apart as per MORT & H Specification 307 including maintenance of hedge for one year including watering etc.

Planting of trees by the roadside (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground mixing the soil with decayed farmyard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year as per MORTH Specification 307

Supply at site of work well decayed farmyard manure, from any available source approved by the engineer-in charge including screening and stacking as per MORT & H Specification 308.2 including Spreading of Sludge Farm Yard Manure or/and good Earth in required thickness

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand ) including testing of joints, etc. complete.- A) 100 mm dia RCC pipe

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand ) including testing of joints, etc. complete.- B) 250 mm dia RCC pipe

Providing and fixing Rigid PVC (SELFIT) pipes for public water supply including Railway freight, carting, loading and unloading, stacking, transit insurance etc, conforming to ASTM 2467 with ISO 14001, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer.conforming to IS 4985-2000 and bearing ISI mark, CLASS 6 KG/ SQ. CM a) Outer dia 63 mm

Providing and fixing Rigid PVC (SELFIT) pipes for public water supply including Railway freight, carting, loading and unloading, stacking, transit insurance etc, conforming to ASTM 2467 with ISO 14001, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer.conforming to IS 4985-2000 and bearing ISI mark, CLASS 6 KG/ SQ. CM b) 75 mm

Providing and fixing Rigid PVC (SELFIT) pipes for public water supply including Railway freight, carting, loading and unloading, stacking, transit insurance etc, conforming to ASTM 2467 with ISO 14001, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer.conforming to IS 4985-2000 and bearing ISI mark, CLASS 6 KG/ SQ. CM c) 110 mm

Providing and fixing Rigid PVC (SELFIT) pipes for public water supply including Railway freight, carting, loading and unloading, stacking, transit insurance etc, conforming to ASTM 2467 with ISO 14001, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer.conforming to IS 4985-2000 and bearing ISI mark, CLASS 6 KG/ SQ. CM d) 140 mm

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall. SCH-40 (blue)/(white) 50mm outer dia.

Proving and fixing white vitreous china extended Wall Hung type (European Type) water closet of approved shape with seat and lid with C.I. brass hinges and rubber fittings with white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/ 8 litre), etc. including chair bracket/rag bolts, cutting & making good the walls and floors where required and concealed seat support - W.C. Pan with white plastic seat and lid

Providing and fixing white vitreous china flat back Large lipped front urinal basin of 590x375x390mm size with Urinal Valve Auto closing system with built in control cock & wall flange with fittings, spreader, R.S. or C.I. brackets, standard size C.P. Brassl flush pipe and spreaders with C. P. brass unions & C. P. Brass clamps with waste fitting as per IS 2556, PVC trap with outlet grating and other couplings in CP Brass complete, including painting, fittings, cutting and making good the walls and floors where required. - Range of one urinal basin

Providing and fixing vitreous china under counter wash basin with RS or C.I. brackets painted white, NICKEL chrome plated copper alloy Fancy Pillar Cock rocket type Jaquar make or equivalent. Confirming to IS 8931;1993, 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. Or C.P. brass trap and union complete, including cutting and making good the walls where required. - wash basin 550x400/Oval 560x410mm/ round 550x450mm including cutting in base etc complete with sealing

Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete

Providing & fixing C.P. Brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C.P. Brass Screws - 600x20mm size

Providing and fixing toilet paper holder - C.P. brass

Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw

Providing & fixing G.I. pipes (B class) complete with G. I. fittings and clamps, including cutting and making good the walls etc. (Internal work) a) 15mm nominal bore

Providing & fixing G.I. pipes (B class) complete with G. I. fittings and clamps, including cutting and making good the walls etc. (Internal work) b) 20mm nominal bore

Providing & fixing G.I. pipes (B class) complete with G. I. Fittings including trenching and refilling etc. (External work) a) 15mm nominal bore

Providing & fixing G.I. pipes (B class) complete with G. I. Fittings including trenching and refilling etc. (External work) b) 32mm nominal bore

Providing & fixing G.I. pipes (B class) complete with G. I. Fittings including trenching and refilling etc. (External work) c) 40mm nominal bore

Providing & fixing G.I. pipes (B class) complete with G. I. Fittings including trenching and refilling etc. (External work) d) 50mm nominal bore

Fixing water meter and stop cock in G.I. Pipe line including cutting and threading the pipe and making long screw etc. complete ( cost of water meter and stop cock to be paid separately.

Providing and fixing brass stop cock (heavy) of approved quality : a) 20mm nominal bore

Providing and fixing brass stop cock (heavy) of approved quality b) 25mm nominal bore

Providing and fixing brass stop cock (heavy) of approved qualityc) 32mm nominal bore

Providing and fixing brass stop cock (heavy) of approved quality d) 40mm nominal bore

Providing and fixing brass stop cock (heavy) of approved quality e) 50mm nominal bore

Providing and fixing brass full way valve (heavy duty) with wheel of approved quality a) 20mm nominal bore

Providing and fixing brass full way valve (heavy duty) with wheel of approved quality b) 25mm nominal bore

Providing and fixing brass full way valve (heavy duty) with wheel of approved quality c) 40mm nominal bore

Providing and fixing brass full way valve (heavy duty) with wheel of approved quality d) 50mm nominal bore

Providing and fixing ball valve (brass) of approved quality High pressure with P.V.C. floats - 20mm nominal bore

Providing, laying and jointing glazed stone ware pipes grade “a” with stiff mixture of cement mortar in the proportion of 1:1 (1 cement :1 fine sand) including testing of joints etc. complete - 150mm diameter

Providing and laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone, aggregate 40 mm nominal size) alround S.W. pipes including bed concrete 15 cm thick as per standard design - 150mm diameter S. W. pipe

Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with C.I grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design - 150 x 100 mm size – P or S type

Constructing brick masonry manholes or inspection chamber with second class bricks in cement mortar 1:5 (1 Cement : 5 Fine Sand), RCC top slab 1:1.5:3 mix (1 Cement :1.5 Coarse Sand : 3 graded stone aggregate 20mm nominal size) Foundation concrete 1:1.5:3 (1 Cement :1.5 Coarse Sand : 3 graded stone aggregate 20mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 Cement : 3 Coarse Sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4mix (1 Cement :2 Coarse Sand : 4 graded stone aggregate 20mm nominal size) neatly finished complete as per standard design. a) Inside size 90x80 cm and 60 cm deep including Supplying and fixing at the site of work of Steel Fibre Reinforced Concrete (SFRC) manhole covers with frames made as per IS :12592 (part I and II) - 1991 in concrete M45grade. The covers and lapped in 2mm thick. steel plate and this plate & lifting hooks are duly painted in corrosion resistant epoxy paint etc. complete. Light Duty (2.50 Metric Tonne Capacity) a) 450x900

Constructing brick masonry manholes or inspection chamber with second class bricks in cement mortar 1:5 (1 Cement : 5 Fine Sand), RCC top slab 1:1.5:3 mix (1 Cement :1.5 Coarse Sand : 3 graded stone aggregate 20mm nominal size) Foundation concrete 1:1.5:3 (1 Cement :1.5 Coarse Sand : 3 graded stone aggregate 20mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 Cement : 3 Coarse Sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4mix (1 Cement :2 Coarse Sand : 4 graded stone aggregate 20mm nominal size) neatly finished complete as per standard design. b) Inside size 60x60 cm and 60 cm deep including Supplying and fixing at the site of work of Steel Fibre Reinforced Concrete (SFRC) manhole covers with frames made as per IS :12592 (part I and II) - 1991 in concrete M45grade. The covers and lapped in 2mm thick. steel plate and this plate & lifting hooks are duly painted in corrosion resistant epoxy paint etc. complete. Light Duty (2.50 Metric Tonne Capacity) b) 450x600

Supplying and fixing at the site of work of Steel Fibre Reinforced Concrete (SFRC) manhole covers with frames made as per IS :12592 (part I and II) - 1991 in concrete M45grade. The covers and lapped in 2mm thick. steel plate and this plate & lifting hooks are duly painted in corrosion resistant epoxy paint etc. complete. Light Duty (2.50 Metric Tonne Capacity) a) 450x600

Providing & fixing rigid PVC SWW (soil, waste and rain water drainage pipes of approved make including lubricant etc. complete ( single/double socketed) a) 110 mm dia

Providing & fixing rigid PVC SWW (soil, waste and rain water drainage pipes of approved make including lubricant etc. complete ( single/double socketed) b) 75 mm dia

Providing & fixing rigid PVC bend (approved make) for SWR pipes including lubricating etc. complete bend with door a) 100 mm dia

Providing & fixing rigid PVC bend (approved make) for SWR pipes including lubricating etc. complete bend with door b) 75 mm dia

Providing & fixing single Tee of rigid PVC (approved make) for SWR pipes including lubricating etc. complete bend with door a) 110 mm dia

Providing & fixing single Tee of rigid PVC (approved make) for SWR pipes including lubricating etc. complete bend with door b) 75 mm dia

Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : a) 110 mm dia

Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : b) 75 mm dia

Providing and fixing double “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : a) 110 mm dia

Providing and fixing double “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door : b) 75 mm dia

Providing & fixing Nahani trap of rigid PVC of (approved make) for SWR pipes including lubricating etc complete with SS door a) 110mm dia

Providing & fixing Nahani trap of rigid PVC of (approved make) for SWR pipes including lubricating etc complete with SS door b) 75mm dia

Providing & fixing U.P.V.C. pipe clips (approved make) for S.W.R pipe a) 110mm

Providing & fixing U.P.V.C. pipe clips (approved make) for S.W.R pipe b) 75mm dia

Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Body Jaquar make or equivalent. Confirming to IS 8931;1993 a) 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931;1993 a) 15mm nominal bore

Providing and fixing NICKEL chrome plated copper alloy Fancy CONCEALED STOP COCK WITH SLINDING FLANCE 15MM Jaquar make or equivalent. Confirming to IS 8931;1993 a) 15mm nominal bore

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. a) 15 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. b) 20 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. c) 25 mm dia nominal outer dia pipes.

Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. d) 32 mm dia nominal outer dia pipes.

Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards.

Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way Bib Cock with single knob and wall flange conforming to IS 8931:1993 15mm nominal bore.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work. SCH-40 (blue)/(White) a) 20mm outer dia.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work. SCH-40 (blue)/(White) b) 25 mm dia nominal outer dia pipes.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work. SCH-40 (blue)/(White) c) 32 mm dia nominal outer dia pipes.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work. SCH-40 (blue)/(White) d) 40 mm dia nominal outer dia pipes.

Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work. SCH-40 (blue)/(White) e) 50 mm dia nominal outer dia pipes.

Supplying & Fixing C.I. Foot valve with metal valve and seat full bore type, having total area through strainer perforations three times that of pipe size suitable for working pressure of 2 kg/sq.cm. As per IS: 4038 (lift type) - 50 mm dia

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete a) Overall size 535mmx460mm (21"x18") bowl size 460mmx380mmx200mm (18"x 15"x 8") depth 200 mm. Glossy. 1.0mm thk,

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Construction of meter box of size1.00x0.45x0.90 m in laterite stone masonry in cement mortar1:5 (1cement :5coarse sand). Foundation concrete of 8cm thick 1:4:8 (1 cement : 4 coarse sand : 8 graded granitic or basaltic stone aggregate 40mm nominal size) RCC top slab 8cm thick 1:2:4 (1Cement:2 coarse sand:4 graded granitic or basaltic stone aggregate 20mm nominal size) including high yield steel bars 8mm dia. 4 nos. each in both directions finished with 12mm thick cement plaster 1:6 (1 cement:6 coarse sand) including white washing with lime, two or more coats to give an even shade. Providing & fixing door cover of mild steel angle frame of size 20mmx20mmx3mm including necessary hinges and holdfast of size 100mmx20mmx3mm (2 Nos.), paintings etc. complete as directed by the Departmental Officer (rate inclusive of earthwork in excavation, rubble packing 10cm thick, refilling of excavated earth etc. complete as per the standard drawing). In the various Scattered locations as per the direction of the Engineer -in-charge

Providing anti termite treatment to the building conforming to IS:6313 (part II) 1971 adopted, including adopting the precautions for health hazards and safety measures as required therein with the cost of all materials, chemicals plants, equipments etc required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guarantee period complete. The payment will be made on the Plinth of the building) a) Preconstruction

Providing and fixing G.I. chain link mesh 6.35cm x 6.35 cm x 10 gauge (2.5” x 2.5” x 10 gauge) fixed with angle iron posts and struts by G.I. or M.S. staples at 20cms apart with welding with the iron posts (placed at 3 metres centre to centre) including providing barbed wire stiffeners (shall weigh 9.33 kg. per 100 metres minimum) at top and bottom with barbed wire stiffers by binding wires at 50cms centre to centre complete as per the direction of the Engineer – in – charge (angle iron posts struts, earthwork and concrete for fencing posts and struts to be paid separately)

Providing and fixing prefabricated compound gate of G.I . pipes 40-50mm dia (medium) with 12mm m.s square bars of G.I . pipes grill work as per drawing including providing and fixing locking arrangements pintals and hold fast embedded in cement concrete 1:2:4 (1cement:2 coarse sand:4 granitic or basaltic stone ballast 20mm nominal size )including applying priming coat with ready mixed red lead paint and painting two or more coats with superior ready mixed approved brand and manufacture in all shades as per direction complete.

Providing and fixing in position Glass Reinforced Concrete (G.R.C) Screens in approved size, pattern, design, thickness (40-50mm thk border + 25-30mm thk inside membrane) and color. The Screens should be made from White Portland Cement, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber, Super Plasticizers, Polymers and U.V resistant Synthetic inorganic pigments should be used for pigmentation. The material casting should take place in Synthetic Rubber / FRP Mould. The fixing of Screens should be ‘Dry fixing’ i.e. to be done with Stainless Steel (SS – 304) ‘L’ shaped Clamps, dash fasteners and pins complete.

Providing & fixing in position traction matting antiskid clear tape 2 inch wide (50mm) for staircase having Granite Treads. The antiskid clear tape should be mineral coated slip resistant material with pressure sensitive adhesive including cleaning, degreasing, priming to mask the surface (if required), presssing using rubber roller etc. complete

Demolishing cement concrete 1:3:6 or richer mix including disposal of material within 50 m lead.

Demolishing R.C.C. work including stacking of steel bars & disposal of unserviceable within 50 mts. lead.

Extra for cutting reinforcement bars in R.C.C. or R.B. work

Demolishing brick work in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Demolishing laterite stone masonry in cement mortar including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Dismantling wood work of sectional area 40 sq.cm. and above wrought framed and fixed in frames, other frames and trusses including stacking of material within 50 mts. lead (span upto 10 mtrs.)

Dismantling wood work of area below 40 sq.cm. wrought framed and fixed in frames, other frames and trusses including stacking of material within 50 mts. lead

Dismantling doors, windows and clearestory windows (steel or wood) shutters including chowkhats architrave holdfast etc. complete and staking within 50 mt. Lead - Of area 3 sq.m. and below

Dismantling doors, windows and clearestory windows (steel or wood) shutters including chowkhats architrave holdfast etc. complete and staking within 50 mt. Lead b) Area beyond 3 sq.m.

Dismantling steelwork in single sections in channels,angles,tees,flats including dismembering and staking within 50 mts. Lead

Dismantling steelwork in built up sections in angles, tees, flats and channels including all gusset plates bolts, nuts, cutting dismembering and staking within 50 mts. lead

Dismantling asbestos sheet roofing including ridges, hips valley and gutters and stacking the material within 50 meters lead.

Dismantling tiled roofing (mangalore or pot or country tiles) with battens etc. complete including stacking of serviceable material & disposal of unserviceable material within 50 mts. lead.

Dismantling wooden boarding in linings of walls & partitions excluding supporting members but including stacking within 50 metres lead. a) Thickness above 19mm and upto 25mm

Dismantling cement asbestos celotex or other ceiling or partition hard broad wall including stacking of serviceable materials and disposal of unserviceable materials within 50 mts. lead.

Dismantling of existing G.I. Pipe including disposal of unserviceable material and stacking of serviceable materials a) upto 20mm nominal bore

Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete wood work, steel work, including T & P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 metresas per MORTH 202 - Dismantling stone pitching/dry stone spalls

Dismantling the existing cables of all types & size upto 10 sq mm.

Dismantling of existing fluorescent fitting of any type & size

Dismantling of existing ceiling fan/ exhaust fan / cabin fan bracket fan complete with accessories, G.I. down rod, frame etc. and making the site clear

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit (heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (a) Group C -- with Cat B Modular Accessories

Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit (heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit (heavy) with 2 way modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. with Cat B Modular accessories

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required - Cat B

Supply and erecting fan hook box (100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required.

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required. - Cat B

Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required. - Cat B

Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as required - Cat B

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit (heavy) of appropriate size as required. a) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit (heavy) of appropriate size as required. a) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit)

Supplying and drawing following sizes of FRLS PVC insulated copper conductor single core cable in the existing surface/ recessed steel PVC conduit or casing caping, including dismantling, removing old wires as required. - 2 x 6 sq.mm

Supplying and erecting square shaped CRCA /die-cast aluminium powder coated housing LED Panel light (slim edge-lit) 600X600mm suitable for 36W-40W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting LED square / circular 16 to 20W downlighter having pressure die-cast aluminium housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting LED Mirror Light with integrated driver including 7W to 9W lamp with polycarbonate housing and opal diffuser to be fixed above mirror or as required on clamps complete.

Supplying & erecting LED 20W tube light fitting (4 feet) with aluminium housing, heat sink, integrated HF electronic driver complete. (including lamp).

Supply and erecting of 48 inch (1200mm sweep) ceiling fan, double ball bearing type, complete with all accessories. - Cat B

Supply and erecting of 9 inch (225 mm sweep) exhaust fan, 1400 rpm, complete with all accessories. - Cat A

Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/RCCB/Isolator) - 8 way double door Cat B

Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) - 6 way (4+18), double door, Horizontal type Cat B

Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator) - 8 way (8+24), double door, Horizontal type Cat B

Supplying installation testing and commissioning of surface/ recess mounting vertical type 415 V TPN, double door MCB DB of sheet steel dust protected duly phosphatised and powder painted inclusive of 200 A tinned copper busbar common neutral link earth bar din bar for mounting MCBs detachable gland knock out plate and with 100 A 10 KA MCCB as incomer interconnection between incomer MCCB and busbars of following ways (but without MCCB/MCBs as required) - 8 way with 100A MCCB as Incomer, double door, Cat B

Supplying installation testing and commissioning of surface/ recess mounting vertical type 415 V TPN, double door MCB DB of sheet steel dust protected duly phosphatised and powder painted inclusive of 200 A tinned copper busbar common neutral link earth bar din bar for mounting MCBs detachable gland knock out plate and with 100 A 10 KA MCCB as incomer interconnection between incomer MCCB and busbars of following ways (but without MCCB/MCBs as required) - 12 way with 100A MCCB as Incomer, double door, Cat B

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. a) SP, Cat B

Supplying, erecting & marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SWSWR/MCB

Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. a) TP, Cat B

Supplying and fixing 63 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. - TP, Cat B

Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. - TPN, Cat B

Providing and fixing following rating and breaking capacity fixed type/adjustible 3 pole MCCB inside the existing cubicle panel board including drilling holes in cubicle panel making connections etc as required - 100 A 25 KA, CAT B

Providing and fixing following rating and breaking capacity fixed type/adjustible 3 pole MCCB inside the existing cubicle panel board including drilling holes in cubicle panel making connections etc as required - 125 A 25 KA, CAT B

Supplying, fixing and commissioning 2 pole, RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per specification no SWRCCB/RCBO

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6A/10A/16A/20A/25/A as per specification no SWRCCB/RCBO

Supplying and fixing SP blanking plate in the existing MCB DB complete as required

Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20 mm Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. g)watering arrangement(plumbing will be paid seperately). a) In soily strata

Earthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20mm, Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e) Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid seperately). a) In soily strata

Extra for using salt and charcoal for GI or copper plate earth electrode as required (96 Kgs of Charcoal and 5 Kgs of Salt)

Supplying and laying 25 mm x 5 mm Copper strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Supplying and laying 25 mm x 5 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required

Supplying and laying 25 mm x 5 mm Copper strip in 40 mm dia GI pipe from earth electrode as required

Supplying and laying 25 mm x 5 mm GI strip in 40 mm dia GI pipe from earth electrode as required

Providing and fixing 25 mm x 5 mm Copper strip on surface or in recess for connections etc. as required

Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for connections etc. as required

Providing and fixing 6 SWG dia GI wire on surface or in recess for loop arthing . as required

Supplying and Installing following size perforated type 16 SWG, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. - 150mm width x 50mm depth

Supplying and Installing following size perforated type , M.S.cable tray bends of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. - 150mm width x 50mm depth (16 SWG)

Supplying and Installing following size perforated type , M.S.cable tray tees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. - 150mm width x 50mm depth (16 SWG)

Supplying and Installing following size welded ladder type , 100mm depth, M.S.cable tray of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. - 300 mm width X 100 mm depth with runner size 25x100x25mm, rung size 20x40x20mm with rungs at 250mm c/c. (12SWG)

Supplying and Installing following size welded ladder type , 100mm depth, M.S.cable tray bend of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. - 300 mm width X 100 mm depth with runner size 25x100x25mm, rung size 20x40x20mm with rungs at 250mm c/c. (12SWG)

Supplying and Installing following size welded ladder type , 100mm depth, M.S.cable tray tees of GI pregalvanised/hot dip galvanised/ powder coated finish, in convenient sections, joined with connectors, suspended from the ceiling with suitable MS suspenders including bolts and nuts, painting suspenders etc, complete as required. - 300 mm width X 100 mm depth with runner size 25x100x25mm, rung size 20x40x20mm with rungs at 250mm c/c. (12SWG)

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554 (Part I) ,IS:7098(Part I) with latest amendments of following size. - 3 1/2 Core 240 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554 (Part I) ,IS:7098(Part I) with latest amendments of following size. - 3 1/2 Core 185 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554 (Part I) ,IS:7098(Part I) with latest amendments of following size. - 3 1/2 Core 70 sq.mm

Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554 (Part I) ,IS:7098(Part I) with latest amendments of following size. - 3 1/2 Core 35 sq.mm

Supply of 3 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. - 3 Core 25 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. - 4 Core 16 sqmm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. - 4 Core 6 sq.mm

Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. - 4 Core 2.5 sq.mm

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 3 1/2 x 240 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 3 1/2 x 185 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 3 1/2 x 70 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 3 1/2 x 35 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required.. 3 x 25 Sq. mm.

Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 4 x 16 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 4 x 6 Sq. mm.

Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 4 x 1.5/2.5 Sq. mm.

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 120 sq.mm but not exceeding 400 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable)and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. - In soily strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 120 sq.mm but not exceeding 400 sq.mm direct in ground in the same trench in one tier horizontal formaion including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required - - In soily strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground in the same trench in one tier horizontal formaion including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required - In soily strata

Laying of one number additional PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground in the same trench in one tier horizontal formation including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required - In soily strata

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 400 sq.mm in the existing masonry open duct, etc. complete as required

Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing masonry open duct, etc. complete as required

Supply and fixing of cable route marker 15 cms diameter of GI plate 6mm thick with inscription theron bolted or welded to 25mm x 25mmx 5mm angle iron 60 cms long and fixing the same in ground with PCC etc complete as required.

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-45 connector (modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. b) Cat B

Supplying and drawing of Cat - 6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVC sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required (a) Cat 6

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-11 connector(modular telephone socket) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. b) CAT B

Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated copper conductor unarmoured telephone cable ITD/DOT approved, with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s), complete as required. a) 2 Pair

Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with modular TV socket including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. a) CAT B

Supplying and drawing of Co-axial TV cable of required grade, solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required. a) RG - 6

Supplying, Installing, Testing & Commissioning of Indoor PoE IR Dome Camera, minimum 2.0 mega pixel, 30m IR distance, 10/100 base T LAN, ONVIF, PoE (IEEE 802.3 af compliant), Day/ Night, Night Vision, Motion based recording, 1/3" CMOS sensor, 0.02 min. lux for colour & 0.1 lux for monochrome, 16:9 aspect ration, 2592x1520, 20 FPS, H.264 Video compression, autofocus with 2.8mm fixed lens, Contrast/ Sharpness/ White Balance/ DWDR/ Privacy masking, power supply, BNC/ DC connectors, Wall/ False ceiling mounting with all necessary accessories.

Supplying, Installing, Testing & Commissioning of Outdoor PoE IR Bullet Camera, minimum 2.0 mega pixel, 30m IR distance, IP66, 10/100 base T LAN, ONVIF, PoE (IEEE 802.3 af compliant), Day/ Night, Night Vision, Motion based recording, 1/3" CMOS sensor, 0.02 min. lux for colour & 0.1 lux for monochrome, 16:9 aspect ration, 2592x1520, 20 FPS, H.264 Video compression, autofocus with 2.8mm fixed lens, Contrast/ Sharpness/ White Balance/ DWDR/ Privacy masking, power supply, BNC/DC Connectors, Wall/ False ceiling mounting with all necessary accessories.

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. a) 20 mm

Supplying, Installing, testing & Commissioning of rack mount, ON/VIF support network Video Recorder suitable for 3MP, 32 input channels for 25 FPS at minimum 4 CIF simultaneous recording in RAID 1 & H.264/MPEG/MJPEG, with continuous/ scheduled/ event and motion trigger record, minimum 4 channel min 4 CIF live playback, with Recording NVR has separate VMS software the same should be included in package and loaded on client viewing with licence for cameras.

Supplying, Installing, Testing & Commissioning of 6 TB surveillance HDD

Supplying, Installing, Testing & Commissioning of Wall bracket mounted professional grade 40" back lit LED screen for workstation operated panel 1920x1080 min, 16:9 aspect, 350 nits, 5000:1 contrast, 1780 H/V, VGA/DVI-D/ HDMI input, RS232C In/Out, Narrow Bezel, stereo input/ output

Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated copper conductor unarmoured telephone cable ITD/DOT approved, with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s), complete as required. a) 50 Pair

Supplying, installing, testing and commissioning of Junction Box, ITD/DOT approved, indoor type with wall mounting/concealed facility having front door with lock along with aluminium frame for mounting disconnection type Krone modules, complete cabinet fabricated from 18 SWG CRCA sheet with powder coating in appropriate manner and suitable for following capacity of pairs, including Krone makemodules, crimping and terminations, etc. complete as required. a) 50 Pair

Supplying, installing, testing and commissioning of Junction Box, ITD/DOT approved, indoor type with wall mounting/concealed facility having front door with lock along with aluminium frame for mounting disconnection type Krone modules, complete cabinet fabricated from 18 SWG CRCA sheet with powder coating in appropriate manner and suitable for following capacity of pairs, including Krone makemodules, crimping and terminations, etc. complete as required. a) 100 Pair

Supplying and drawing/fixing jelly filled outdoor type armoured telephone cable with 0.5 sq.mm dia. tinned copper conductor, ITD/DOT approved, with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s), complete as required. a) 5 Pair

Supplying and installing, testing & commissioning of digital (hybrid) type EPABX (Electronic Private Automatic Branch Exchange) of 6 x 96 extensions suitable upto 96 extensions complete.

Supplying, installing, testing & commissioning push button telephone instrument desk top/wall mount unit as per specification complete

Supplying and fixing 1 meter length, UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying, fixing, and configuring ethernet managed ethernet switch of 24 ports with 2 SFP + 2 combo port and web view/CLI on provided rack or as directed as per specification no. WG-NWC/GBS

Supplying, fixing, and configuring Web Smart Power over Ethernet Switch of 24 Ports, on provided rack or as directed as per specification no WGNWC/ENS

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing 6U Wall Mount Rack (Dimension-DxWXH - 450X550X367 mm) as per specification in approved manner

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Providing & erecting 7 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no.OHPL/OPL.

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings as per specification No. FF-PP

Supplying and erecting Street light bracket made from 25 mm. dia ‘B’ class G.I. Pipe, 0.6 m in length along with pole cap of 300mm length and 80 mm dia duly welded with provided leads as per specification no. FG-BKT/BPC

Supplying and erecting LED street light fitting suitable for above 70W- 75 lamp, including lamp, with PF > 0.95 class IP 65 and above housing of pressure die cast aluminium alloy and heat sink extruded aluminium complete per specification No FGODF/FLS2

Supplying and erecting Gate/garden light fitting with 200mm dia. glass bowl suitable for upto 12W LED lamp on provided pipe as per specification No. FG-ODF/GLT

Supplying & erecting 5W-7W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying and erecting water light terminal box of 1.6mm thick ( 16 gauge ) CRCA sheet of size 200 x 150 x 150 mm complete on pole as per speciffication no CB-SB

Supply, Fabrication, Erection, Testing and Commissioning of Main Panel floor mounted with frame of suitable M.S channel dully painted, fabricated of 14/16 swg CRCA sheets completely derusted, chemically treated and powder coated with shade suggested by client and having following items as per single line diagram:- 600/630A, 36KA, Adjustable TP MCCB - 1 no. wiring for ammeter having Three and half digit LED display, external C.T. operated, calibrated for suitable to operate on 500V, 0 to1000A AC supply, L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio with 15VA, 3 pilot lamps all Bakelite with colour glasses with miniature lamps 230 V/250V from CSS and conected to 630A, Aluminium Busbar with outgoing feeder of 1no160A, TP MCCB, 5nos 100A, TP, MCCB along with 400A ON LOAD transfer switch and which have other incoming supply from DG with 400A, TP, 35/40KA adjustable MCCB wih Voltmeter and Ammeter connected to ATS with 400A, 4P, busbar and outgoing feeders of 1no, 125A, TP, MCCB 2nos, 100A, TP, MCCB complete as per single line drawing of MLTP

Supplying & erecting on line UPS pure sine wave of 2 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins battery backup, as per specification no. AP-UPS

Supplying and erecting Centrifugal water pump (Monoblock), 415V, three phase 50 cycles A.C. supply of 2.25 KW/ 3 HP with discharge 2/4.9 Litres per second (LPS) for head of 14/36 m and 50 mm suction/ 40 mm delivery pipe on provided C.C. foundation as per specification no. WP-CGP

Supplying and erecting D.O.L. Starter 400V. 3 phase, 50 cycles with no volt coil and overload element with necessary materials and connected to supply upto 7.5 H.P.

Supplying & erecting automatic control panel for 3 Ph, 415 volt, A.c. Submersible/centrifugal pump set upto 7.5 HP consisting of DOL starter having relay range 9-14 AMP, S.P.P., Combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc

Supplying, installing, testing & commissioning compact substation with 3 phase, 11/0.433 kV, 50 Hz., 250 kVA, oil immersed copper wound transformer having indoor type transformer bushings, with HT side (incoming side) load break switch of appropriate capacity and LT side (outgoing side) MCCBs (4 pole) of appropriate capacity , with inbuilt metering cubical, standard accessories complete with test certificate with losses below 980 Watts at 50% load, 2930 Watts at 100% load for transformer, as per IS:1180 - 2014 energy efficieny level II, with necessary permissions of Electrical Inspector, as per specification no SS- TR.

Supplying & erecting 11 kV 630A, indoor type ring main unit with 1 or 2 incoming & 2 or 1 outgoing with HRC fuses complete erected on provided cc foundation/MS channels/trench, etc, as per specification no SW-HTS / RMU

Supplying , erecting & terminating 3 x 95 sq. mm. aluminium 11 kV(E), XLPE armoured cable on wall/ceiling or laid in provided trench / pipe in an approved manner as per specification no. CBHT

Providing and erecting Heat shrinkable indoor termination kit for 11 kV ( E ) XLPE HT cable 3x up to 95 sq. mm. with necessary material as per specification no. CB-JT/HT

Providing and erecting Heat shrinkable out door termination kit for 11 kV ( E ) XLPE HT cable 3 x up to 95 sq. mm. with necessary material as per specification No. CB-JT/HT

Providing printed instruction chart for treating persons suffering from electric shock, printed in English & Marathi and duly laminated complete.

Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working upto 22 kV supply complete.

Providing Round bottom fire bucket of 9 Litres capacity as per IS :2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.

Providing Floor mounting stand for keeping 4 Nos. of FIRE buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4 hooks and duly painted with one coat of red lead and two coats of silver paint complete.

Supplying and erecting fencing of section having size 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete as per specification no SS-AS/FSG

Supplying and erecting 50 x 50 x 6 mm angle iron as corner support 2m long fixed at the middle of the fencing frame and the other side inclined at 30 degree angle, in cement concrete foundation of 15 x 15 x 40 cm complete duly painted with one coat of red oxide and two coats aluminum paint complete

Supplying and erecting double leaf hinged door each 1500 mm in width x 1850 mm in height using B class, GI pipe with angle iron supports, chain link wire mesh (jali) complete supported on channel iron, erected in foundation, and painted complete as per specification no SS-AS/DLD

Supplying, Installing, Testing and Commissioning (SITC) of Electric Traction Passenger Lift with • Rated capacity :- 8 Passenger/544Kg • Floors :- B+G+5 floor (7Stops/7 Landings) • Travel :- 19.5 mtrs • Location of Lift Machine:- Machine Room Less (MRL) • Rated speed :- 1.0mps Variable speed (VS) • Doors type :- Centre Opening Power Operated (COPO)/ Telescopic Opening Power Operated (TOPO) Doors with frame having clear opening of 800 mm wide x 2000mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves /frames. • Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. • Car Operating Panel (COP) with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with Floor Position Indicator (FPI), scrolling UP/DN LED indicator & with/without attendant key switch, Overload warning Device (OWD) with audio-visual alarm, Voice annunciation system (VAS) in Konkani/Marathi, Hindi & English with intercom system with telephone instrument in Lift car & FCC/ground floor • Clear Car size of 1100mm wide x 1300mm deep x 2250mm high • Landing Operating Panel (LOP) with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with Car Position Indicator (CPI), Lift car arrival & next travel direction audio-visual indication at all landings Lift controller based on microprocessor/ Programmable Logic Control (PLC) with Variable Voltage Variable Frequency (VVVF) Drive having closed loop control system, with Intelligent Building Management System (IBMS) compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor/ control card & allied accessories control panel having enclosure of 1.5mm Cold rolled Close Annealed (CRCA) sheet with powder coating with IP54 Protection class • Automatic Rescue Device (ARD) complete with necessary Sealed maintenance free (SMF) Valve-Regulated Lead-Acid (VRLA) batteries • Fireman controller having fireman switch at fire Landing, • Closed Circuit Television (CCTV) surveillance system comprises of 2nos minimum 2.0MP FHD IP (Internet Protocol) based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with Network Video Recorder (NVR) kept in LMR/Fire Command Centre (FCC) with High Definition Recording (HDR) data backup for 60 days with 18" Full High Definition (FHD) TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. • Lift Machine of Gearless Permanent Magnet Synchronous AC Machine (PMSM) of suitable kW with Traction pulley, Over speed safety governor (OSG), electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on Lift machine room (LMR) floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength • Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work.Minor civil work for alteration if any and erection of door frames and accessories, erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails fixing of girders for mounting lift machine etc. complete as per specification no. LFT. • Lift shaft available having clear size of 1800 mm wide x 1800mm deep, 1300 mm Pit depth, 4000-4200mm Overhead. Including For Lift having 800mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrows indicators, extension of guide rails, shaft wiring with trunking, travelling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories, door operator mechanism with drive, required aluminium sill, infrared curtain & necessary wiring with interlocking arrangement etc. necessary for the normal safe functioning of lift installation complete. • Full Collective Control System • Duplex Lift control system 1) General: - Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge. 2) Warrantee: - Job covers three years onsite warrantee for all the Lift parts with FCAMC as per the maintenance schedule.

Supplying, installing, testing and commissioning with perfect aligning, proper levelling of fire service main single stage pump, of 2400 LPM at 76 m head centrifugal type, 75 HP (55 kW) 3 phase, 415 volt, 50Hz or of suitable HP complete as per specification no. FF-MFP/SSC

Supplying and installing, testing, perfect aligning and proper levelling and commissioning of Diesel operated fire service stand by pump, of 2280 LPM, @ 70 m head, centrifugal type, single stage pump, including all accessories like Suitable fuel tank, battery, exhaust pipe with silencer, suitable foundation etc.

Supplying, installing, testing and commissioning with perfect aligning, proper levelling of jockey pump of 240 LPM at 56 m head, 15 HP (11 kW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/JP

Supply, installation, testing and commissioning of Fire Pump Control Panel (MCC). The control part should have logic such that, in the event of any Hose reel or landing valve is opened, then the pressure in the line drops and the pressure switches installed on the pump manifold give the indication for the jockey pump to start. If more than one landing valves are opened then as sufficient pressure is not built up in the line by jockey pump, hence it will stop and main pump starts. Incase of power failure, diesel pump should start automatically. Floor Mounting Type.

Supplying and erecting cast iron double flange sluice valve 160 mm dia. as per specification No. FF-VL/SV

Supplying and erecting cast iron double flange sluice valve 100 mm dia. as per specification No. FF-VL/SV

Supplying and erecting cast iron double flange sluice valve 75/80 mm dia. as per specification No. FF-VL/SV

Supplying and installing cast iron foot valve Ball type/Flap type of size 150 mm dia with strainer for negative suction as perspecification No.FF-VL/FV

Supplying and installing cast iron foot valve Ball type/Flap type of size 80 mm dia with strainer for negative suction as perspecification No.FF-VL/FV

Supplying and erecting cast iron double flange NRV of size 100 mm dia. complete as per specification No. FF-VL/NRV

Supplying and erecting cast iron double flange NRV of size 75/80 mm dia. complete as per specification No. FF-VL/NRV

Supplying and installing pressure gauge of 100 mm dia., 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, and G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supplying and installing pressure switch with 12/15 mm dia. Isolation valve, G.I. nipple, elbow, etc. complete as per specification no. FF-FFA/PS

Supplying and erecting Stainless Steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV.

Supplying fire fighting Reinforced Rubber lined (R.R.L.) Hose pipe, 63 mm dia, 15 m in length, fitted with necessary accessories complete as pre specification no. FF-FFA/RRL

Supplying and erecting M.S./CRCA cabinet for housing Floor Hydrant valve, hose pipe, hose reel and branch pipe (size 1000 x 736 x 736 mm.) made from 16 SWG sheet and angle iron 25 x 25 x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying & erecting Stainless steel branch pipe of 63 mm dia. Fitted with 20mm dia detachable hexagonal nozzle complete as per specification no. FF-FFA/NZ

Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30 meter long high pressure polypropylene (Polyhose) fitted with necessary accessories complete. As per specification no. FF-FFA/HV

Supplying and erecting fire brigade header (siamese connection) of 150 mm dia for supplying water to wet riser system complete as per specification no. FF-FFA/SMC

Supplying and erecting fire brigade header of 150 mm dia, for supplying water in fire tank complete as per specification no. FF-FA/FBC

Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV

Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade/ SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying & Installation of 25 mm Size Ball Valve

Supplying and erecting G.I. pipe above ground of 'C' class ERW (Electrical Resistance Welding) of size 25 mm dia with necessary fittings complete as per specification no. FF-PP

Supply and installing G.I. pipe above ground of 'C' class ERW of size 32 mm dia with necessary fittings as per specification No.FF-PP

Supply and installing G.I. pipe above ground of 'C' class ERW of size 40 mm dia with necessary fittings as per specification No.FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings complete as per specification No. FF-PP

Supplying and erecting G.I. pipe above ground of ‘C’ class ERW of size 65 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 75/80 mm dia with necessary fittings complete as per specification no. FF-PP.

Supplying and erecting G.I. pipe above ground of 'C' class ERW of size 100 mm dia with necessary fittings complete as per specification no. FF-PP.

Supplying and erecting G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings complete as per specification no. FF-PP

Providing coating of Bitumen Paint & 4mm thick Wrapping for underground 100 mm Ring Main of Fire Fighting System.

Providing coating of Bitumen Paint & 4mm thick Wrapping for underground 150 mm Ring Main of Fire Fighting System.

Supplying, installing, testing and commissioning addressable type heat detector complete on box as per specification no. FF-FAS/HD

Supplying, installing, testing and commissioning addressable type optical type smoke detector complete on box as per specification no. FFFAS/SD

Supplying, installing, testing and commissioning addressable type manual call point (Pill box) with break glass push button in metal enclosure complete as per specification no. FF-FAAS/MCP

Supplying, installing, testing and commissioning addressable type hooters with CRCA enclosure complete as per specification no. FF-FAAS/HTR

Supplying, erecting, testing and commissioning vane type water flow detector suitable for detecting flow of water in wet sprinkler pipe of main line or branch lines of following dia having following features 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4) Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT (Single pole double track) synchronised switches 7) serviceable without draining pipes - 65mm dia

Supplying, erecting, testing and commissioning vane type water flow detector suitable for detecting flow of water in wet sprinkler pipe of main line or branch lines of following dia having following features 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4) Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT (Single pole double track) synchronised switches 7) serviceable without draining pipes - 75/80mm dia

Supplying, erecting, testing and commissioning vane type water flow detector suitable for detecting flow of water in wet sprinkler pipe of main line or branch lines of following dia having following features 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4) Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT (Single pole double track) synchronised switches 7) serviceable without draining pipes 100mm dia

Supplying, installing, testing and commissioning of 01 Loop addressable type fire alarm control panel (FACP) with standard accessories 230V AC, standby battery & battery charger with LCD display, facility to integrated control module, monitor module, detectors like photo-electric detectors & std. facilities complete as per specification no. FF-FAAS/FACP

Supply, installation, testing and commissioning of Tube trace fire supression System for Main Panel SIZE: 60mx2.5mx0.5m

120 Minutes Fire rated Door System for Electrical Room 1x2 mtr conforming of BS 476 part (20& 22), tested at CBRI. Fire door shall befitted with appropriate fir resistant fittings, such as frame and door.

Supply, installation, testing & commissioning of isolator module with back box addressable for alarm panel.

Supplying, installing, testing and commissioning FRLS, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CBLT/CU

Supplying, erecting & terminating XLPE armoured cable 3 core 35 sq. mm. aluminium conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3 core 6 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, installing, testing and commissioning FRLS, XLPE armoured cable 12 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CBLT/ CU

Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/ recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. - 25 mm

Supplying and erecting ABC powder type fire extinguisher as per IS : 13849/ 15683 of 1 kg capacity with necessary clamp for erection on wall.

Providing & Fixing Self luminating signages of size 100mm x 300mm (4" x 12") with necessary accessories all complete, indicating Exits, Fire Extinguishgers, Hose Reel, etc

Supplying, erecting, testing and commissioning of 15 mm (½") dia. NBCM Body chrome finished quartzoid bulb sprinkler having 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FF-SPR

Boring holes vertically true to line and form for R.C.C. bored piles (Bored cast-in-situ) of required diameter in all strata including removing slush, all kinds of soil and rock (including socketing upto 2 times diameter of pile in hard/soft rock), percolating water etc. complete from the above to keep ready for concrete (including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads) after placing reinforcement but excluding the cost of providing and laying concrete and reinforcement. a) 500mm dia bore upto 21.0m depth from ground (length of pile for payment shall be measured up to bottom of pile cap). All work to be done as per IS 2911

Providing and laying reinforced cement concrete of grade M 40 (mix design) with coarse sand and graded granitic or basaltic aggregate 20mm nominal size as per mix design requirements in bored cast in situ piles of specified diameter at the required workability and compaction as per the direction of the Engineer-in-charge including all operation for placing the concrete, lifting the casing in stages etc. but excluding the cost of reinforcement. a) 500mm dia pile upto 21.0m depth from G. L. (including welding of reinforcement, lowering reinforcement cage, use of tremie, dressing the excess pile concrete upto to pile cutoff level). All work to be done as per IS 2911

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/ Anchor Piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. a) Single pile above 100 tonne and upto 150 tonne safe capacity - Initial Test (Test load 2.5 times the safe capacity)

Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/ Anchor Piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge. Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge. b) Single pile above 100 tonne and upto 150 tonne safe capacity - Routine Test (Test load 1.5 times the safe capacity)

Cyclic vertical load testing of pile in accordance with IS Code of practice IS: 2911 (part IV) by Kentledge/ Anchor Pile method including preparation of pile head etc for. a) Single pile above 100 tonne and upto 150 tonne capacity

Lateral load testing of single pile in accordance with IS Code of practice IS : 2911 (Part IV) for determining safe allowable lateral load on pile : a) upto 50 tonne capacity pile

Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, all complete as per direction of Engineer-in-charge.

High Strain Dynamic Pile Testing on r.c. bored piles using Pile Driving Analyzer. The equipment shall have ability to record both force and velocity. Both strain and acceleration sensors shall be used to collect data & atleast 2 pairs shall be connected at diametrically opposite sides of the pile. The test and equipment shall conform to ASTM D4945-2000 & include CAPWAP analysis. The CAPWAP match quality shall be preferably less than 5. The test shall be conducted by an experienced independent test agency that has demonstrated their capabilities by performing reliability studies in various conditions such as for friction piles, end bearing piles etc. and/or by publishing technical literature through the known forums. The testing agency should have atleast five years experience with testing of bored piles a) above 100 tonne and upto 150 tonne capacity pile

Providing, placing and driving in position 6 mm thick permanent M.S.Liner upto required depth with 12 mm thick M.S. cutting edge of 0.5 metre length of bottom including fabricating, cutting the M.S. sheet to required diametre and shape, welding the joints and driving with the help of required machineries including all materials, labour and lift etc. complete.

Providing and applying as per technical specification anticorrosive treatment consisting of 2 coats of coal tar epoxy with one coat of zinc rich epoxy primer (total dry film thickness 50 + 80 + 80 = 210 microns) for foundations, liner of pile and substructure in contact with soil / earth or water.

Providing corrosion resistant steel CRS-50 bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) (Confirming to IS 1786 if 1985) for RCC work including bending, binding & placing in position in all the floors along with factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member .

BAGKIYA CONSTRUCTIONS PVT LTD