GE(S) BTD TOKEN NO 60 OF 2022-23 PROVISION OF CERTAIN SPECIAL REPAIR AND MINOR WORKS UNDER AGE BR II AND EM IV UNDER GARRISON ENGINEER (SOUTH) AT BATHINDA MILIATARY STATION

Amount

S&F factory made PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening complete all as specified and as directed in Preamble 8B.2.8 of SSR Part -II (2010) and all as shown on drawing on Sl Page No 160 of SSR Part-II (2010).

S & F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 guage thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail panelling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings

Supply and fixed aluminium anodised 100mm long butt hinges with galvanised mild steel hinge pin, anodised and fixed, complete all as specified and as directed

S&F aluminium anodised barrel tower bolt, 150 mm long (ISI marked), fixed to PVC door with screws complete all as specified and as directed.

S & F Aluminium anodised handles, 125 mm long, cast type, (ISI marked) complete all as specified and as directed.

S & F Aluminium anodised handles, 150 mm long, cast type, (ISI marked) complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4 Sqm each complete all as specified and as directed.

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 125 x 60mm, complete all as specified and directed. (thickness of steel sheet shall be 1.25mm). Note:- The quoted rate deemed to include the cost of making good the disturbed surface with cement plaster 1:6 and matching the colour of new plaster with existing surface. Nothing extra shall be paid on this account.

S & F pressed steel frames for doors with one or more rebates including hinges, lock strike plate, fixing lugs, etc., size of frame 105 x 60mm, complete all as specified and directed (thickness of steel sheet shall be 1.25mm). Note:- The quoted rate deemed to include the cost of making good the disturbed surface with cement plaster 1:6 and matching the colour of new plaster with existing surface. Nothing extra shall be paid on this account.

M & L for PCC (1:3:6) type C-1 using 20 mm graded stone aggregate in copings, filling in bed block of hold fast and the like including weathering, slightly rounded or chamfered angles and throating, as directed including necessary formwork complete all as specified and as directed

Demolition of unreinforced concrete in ground floors and pavings in not exceeding 15cm thickness (below or above ground floor level) complete all as specified and directed.

Supply and fixing 35 mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), using 2nd class hard wood (Bonsum / Hollock), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed. Note - Wire gauze / glass to be measured and paid separately

S & F stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aperture 1.4mm and fixed with tinned tacks to stainless steel wire stapple complete all as specified and directed.

S & F 300mm long aluminium sliding doors bolts, plate type, stove enameled black bolts and nuts, four on bolt plate and two on staple complete all as specifiedand directed.

Supply and fixing 300mm long mild steel sliding door bolts with hasp and staple, length of bolt , plate type, stove enameled black, with bright bolts not less than 12 mm dia with and including a minimum of 6 bolts and nuts, 4 on bolt plate and 2 on staple plate and fixed, complete all as specified and as directed

Supply and fixing 200 mm long, mild steel barrel tower bolts, stove enamelled black with bright bolts and fixed (ISI marked) complete all as specified and as directed

Supply and fixing 150 mm long, Mild steel pressed handles, oval type, stove enamelled black (ISI marked) complete all as specified and as directed

Supply only Butt hinges, 100 mm long, medium weight, cold rolled mild steel, (ISI marked) complete all as specified and as directed

S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S & F 4.0mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S & F 4.0mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane fixed with oil putty or wooden beads including provn of glazing pins/spring clips wherever necessary complete all as specified and directed.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and directed

M & L for painting to old wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces complete all as specified and directed

Demolition of cement concrete (unreinforced) including tiles of any description & terrazo finish, etc. not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.and Brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry & pointed in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and directed.

M&L non skid floor tiles, colored, of size 400x400x7mm thick or of size as approved as in floors set and jointed in neat cement slurry & pointed in white cement with pigments to match over and including the provision of 10mm thick bedding layer in CM 1:6 complete all as specified and directed.

All as per ser item No. 27 But on vertical surfaces as in skirting etc on 10mm thick coat in CM 1:4 complete all as specified and directed.

M & L glazed ceramic coloured tiles of approved quality in vertical surfaces 450mmx300 mm x7mm/450mm x 350 x 7mm thick set jointed in neat cement slurry/paste and pointed in coloured cement to match with the tiles over and including 10mm thick plaster in CM 1:4 complete all as specified and directed.

M & L Non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bedding layer in CM 1:6 complete all as specified and directed.

M & L for glazed ceramic colored tiles of size 300x450x6mm thick or of size aproved in dado, set and jointed in neat cement on and including the provision of 10mm thick rendering in CM 1:4 complete all as specified and directed.

Material and labour for machine cut kota stone slab flooring 18 to 20mm thick over 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

All as per Item No. 32 But in vertical surfaces such as steps, riser, skiriting, dado and pillars over and including in 10mm thick CM (1:4) complete all as specified and directed.

M&L for machine cut Kota stone slab flooring 20-25mm thick jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick rendering in CM(1:6) complete all as specified and directed.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM(1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Supply and fixing brass chromium plated shower rose 125 mm size, with swivel joints, including fixing to steel pipe or union, complete all as specified and directed.

Supply and fixing in repair brass chromium plated shower rose 125 mm size, with swivel joints, including fixing to steel pipe or union, complete all as specified and directed.

S & F brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges complete all as specified and directed.

S & F in repairs brass chromium plated tubular towel rail, 20mm dia, D type 60cm long between flanges complete all as specified and directed.

S & F in repair sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x460mm bowl size 410mm x330mm x160mm complete all as specified and directed.

M&L for 25mm dia fancy type PVC coated on MS pipe coloured curtain rod with brackets and knobs at both ends as per site requirement including taking down old existing PVC conduit pipes with accessories complete all as specified and directed.

Taking down or up 15 mm bore galvanised iron tubing/PL-AL-PE pipes and connection complete all as specified and directed.

Taking down or up 20 mm bore galvanised iron tubing /PE-AL-PE pipes and connection complete all as specified and directed.

S & F 15 mm bore GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors complete all as specified and directed.

S & F 20 mm bore GI tubing medium grade with all fittings and fixed to walls & ceilings or laid in floors complete all as specified and directed.

Refixing old GI tubing 15 mm bore pipe and connections in new or old position as on walls ceiling floors etc complete all as specified and directed. (i) Cleaning of pipe is included in seperate item here in before. (ii) Rates quoted by the contractor deemed to be included S & F new fittings as required at site.

S&F PVC110mm bore (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls with MS clamps complete complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) fittings such as bends, tee, shoe etc; fixed to PVC pipes, complete all as specified and directed.

S&F in repair vitreous china (white) squatting pan 'Orissa' pattern, white, size 580 x 440x260 mm, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flush pipe, anti-syphonic pipe etc including making good to floor and including trap set in and including lime concrete complete all as specified and directed.

S&F in repair 10 litres capacity, PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply and fixed in repair Vitreous china wash hand basin, white, flat back, fancy type, size 550 x 400 mm including cast iron cartilever bracket 32 mm dia brass waste coupling and including fixing of taps, waste fitting and union complete all as specified and directed. Note :- Pillar tap shall be measured as supply only under respective item.

Supply only 15mm bore quarter turn, pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F in repair PVC connection 15 mm size with brass nuts of length 450mm of approved quality with PTMT nuts complete all as specified and directed.

Dismantling and disconnecting of existing CI soil vent pipe 100 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed.

Dismantling and disconnecting of existing CI soil vent pipe 75 mm bore fixed to wall,laid in trenches incl all fittings & accessories complete all as specified and directed.

S & F 75mm bore cast iron (spun) sand soil waste and vent pipe with or without ears fixed with chemical cement joints laid in trenches/floors or fixed in walls complete all as specified and directed.

S & F 100mm bore cast iron (spun) sand soil waste and vent pipe with or without ears fixed with chemical cement joints laid in trenches/floors or fixed in walls complete all as specified and directed.

S & F 75mm bore bends (any radius),diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and directed

S & F 100mm bore bends (any radius),diminishing pieces or tapers (larger bore measured) with oval access door complete all as specified and directed

S & F 100mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brancheswith oval access door bore complete all as specified and directed.

S & F 75mm bore branch pieces, single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel brancheswith oval access door bore complete all as specified and directed.

S & F 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F 100mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S & F in repair 100mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

Demolition of reinforced cement concrete of any description & in any position not otherwise specifically provided for, complete all as specified and directed.

M&L for cement concrete 1:2:4 type B1 using 20mm graded crushed stone aggregate as in bedding, benching of manholes, copings, roof padding/kerbs or mud stops, rounded or chamfered on edges etc including necessary from complete all as specified and directed.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bent to shape, required including cranking, bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed. (NOTE : Weight of binding wire shall not be considered for measurement and payment purpose.)

All as per item No. 68 But 8mm dia stirupps, spacers and binders complete all as specified and as directed.

S & F in repairs 15mm bore fancy type chromium plated brass, quarter turn, bib tap long body, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15mm bore fancy type chromium plated brass bib tap long body, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F15 mm bore fancy type stop valve for cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15 mm bore fancy type stop valve quarter turn for cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for brass ferrule complete all as specified and directed.

S & F 15mm bore fancy type chromium plated stop valve, quarter turn, cast copper alloy, with long shank & cup (concealed type) with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair chromium plated soap tray of size 125mm x 125mm x 1mm stainless steel any type and dixed to plugs on wall wit chromium plated brass screws complete all as specified and directed.

S & F 20mm bore, gun metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F 15mm bore pillar taps, fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S & F GI tubing 15mm bore medium grade with all fittings and fixed to walls & ceilings or laid in floors, including connection to existing PVC tank complete all as specified and directed.

S & F GI tubing 20mm bore medium grade with all fittings and fixed to walls & ceilings or laid in floors, including connection to existing PVC tank complete all as specified and directed.

S & F PVC connection 15 mm size with brass nuts of length 600 mm of approved quality complete all as specified and directed.

S & F urinal spredaer of PTMT any colour for fixing with 15mm dia pipe (minimum weight 60 gms) complete all as specified and directed.

M & L for 10user 2000 ltrs capacity FRP moulded Anaerobic Septic Tank for an anaerobic design in which bacteria treats waste under most favorable conditions, process effectively prevents rapid accumulation of sludge and suspended solids from passing through the system untreated with innovative engineering design of the inlet-outlet short circuit of wastewater which is prevented to ensure long and enough retention time for effctive treatment, thus the effluent does not contain any solid or scum that could clog up the pipe line. The septic tank is buried underground, solid and liquid waste flow into it. Heavy solid waste settle to the bottom of the septic tank (known as sludge). The liquid wates are also held in the septic tank while bacteria break down solids into liquids in an anaerobic environment, process is known as primary treatment some bacteria and viruses are adsorbed onto solid particles and held in the sludge or scum layers, allowing for limited removal of disease cusing organisms at the stage. All that has to be done for fitting the tank is to fill the tank with water, connect the drain line to the inlet and outlet to the soak pit. Cover the manholes with the lids provided and tank is ready to use including PCC 1:4:8 below foundation and vent shaft connection, including excavation returning and filling, removal of excess soil, connection to existing sewage line including site clearance etc. complete all as specified and directed.

Supply and fixing Vitreous china wash hand basin, white, flat back, fancy type, size 450 x 300 mm inccluding fancy type 32mm waste coupling including taps, waste, chain and plug and porcelain stopper, brackets, cutting and pinning in ends of brackets or erecting stand, fixing of waste pipe etc, complete all as specified and as directed.

S & F 100mm bore cast iron cowl complete all as specified and directed.

S & F 75mm bore cast iron cowl complete all as specified and directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) not exceeding 1.5 Sqm each exceeding and removal from site complete all as specified and as directed.

S & F strutural steel work as in MS joint, channel, angle, or tee sections, fixed indeprndently, without connecting plates, etc (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed conforming to Fe 290 Gde E-165 complete all as specified and as directed.

Dismantling framed timber scantlings 40 sq. cm and over in section, in any position complete all as specified and as directed.

S & F ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe of size 20mm bore ( weight 210 gms Minimum) complete all as specified and as directed.

Dismentalling water tanks exceeding 250 ltr and not exceeding 500 ltr capacity including removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc. complete all as specified and directed

Supply and fixing three layers 500 liter HDPE water storage tanks polyproof. white in colour rotational moulded polyethylene (cylindrical vertical with closed top) hoisted and fixed in position including S&F of suitable size inlet/outlet arrangement complete all as specified and as directed.

Material and Labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide or zinc chrome complete all as specified and as directed.

Material and Labour for preparation of old steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over two coats of red oxide or zinc chrome complete all as specified and as directed.

Taking down rain water pipe and eaves gutters (any size and pattern) incl all fittings heads shoes bends swan necks etc. complete all as specified and as directed.

Dismantling of brick tiles or terracing tiles, single layer on roof and disposal off retrieved material up to a distance of 100m where complete all as specified and as directed.

Demolition of mud in roof any thickness including plastering and leeping and disposal of rubbish up to a distance not exceeding 100m where complete all as specified and as directed.

S & F CP grating (with or without waste hole), 125 mm size, fixed on floor / nahani traps etc complete all as specified and directed.

M&L for Epoxy joints over cast iron pipe of 100 mm bore pipes, bend joints etc. provided in lieu of cement joint complete all as specified and directed.

Form work to chullah hoods, chajjas, troughs and similar items including edges complete all as specified & directed.

Formwork for rough finished surfaces to soffit of suspended slab such as roof slab, floor slab/chajjas/beams/colns/fins/facia and spiral stair case not exceeding 200mm tick complete all as specified and directed.

Form work to sides of pillars , posts, struts piers, columns and stanchions and similar works rough finished complete all as specified & directed.

Formwork for rough finished surfaces to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

Formwork to sides and soffits of roof beams, gable beams & lintel beam rough finished surfaces of concrete complete all as specified and directed.

M&L brick work with sub class `B' old size bricks straight or curved on plan exc 6.0m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with sub class 'B' old size bricks, straight or curved on plan to any radius in half brick walls built in CM (1:4), etc; complete all as specified and directed.

M&L brick work with sub class 'B' old size bricks, straight or curved on plan to any radius in half brick walls built in CM (1:4) but except bricks (old serviceable bricks to be used) complete all as specified and directed. Note : The rate includes for cleaning of old bricks.

Material and labour for RCC M-25 design mix (using 20mm graded aggregate ) as in chajja, fasia and similar items complete all as specified and directed

Material and labour for RCC M-25 design mix (using 20mm graded aggregate ) as in Columns, pillars, piers, posts and struts complete all as specified and directed

M & L for provinding RCC M-25 design mix as in footings, foundations beams, plinth beams etc complete all as specified and directed

Material and labour for RCC M-25 (design mix) using 20 mm graded stone aggregates as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, shelves and the like etc complete all as specified and as directed

Material and Labour for providing RCC M-25 using graded aggregate in for beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports,overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed

M & L for form work to sides of foundation sides & sofits of foundation beams plinth beam etc and similar work vericle or batter for rough finished surface of concrete flats complete all as specified and as directed

Demolition of brick work or stone / boulder masonary, built in cement mortar including all quoins, arches, pillars etc., complete all as specified and directed.

S&F ball brass valves, high pressure, with polythene float & fly nut complete, screwed for iron pipe or brass ferrule,of size 20mm, etc complete all as specified and directed.

Material and Labour for PCC 1:5:10 type E-2 using 40mm graded aggregate as in foundation filling and mass concrete complete all as specified and directed.

Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M& L for 15mm thick rendering in CM (1:4) on fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cement and using with intgral water proofing compound complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L for 15mm thick rendering in CM (1:6) on other than fair faces of brick work or concrete finishing even & smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in CM (1:6) on fair faces of brick work or concrete finishing even & smooth without using extra cement complete all as specified and directed.

M & L for rendering 5 mm thick in cement mortar in (1:3) on ceiling and finishing the surface even & smooth without using extra cement complete all as specified and directed.

M & L for rendering 10 mm thick in cement mortar in (1:4) and finish the surface rough to receive the tile finish etc complete all as specified and directed. Note:- Rendering will be done in course sand (Toka sand) only.

M&L applying three coats of white wash on newly plastered surfaces on wall including preparation of surface, complete all as specified and directred.

M&L applying three coats of white wash on newly plastered surfaces on ceiling including preparation of surface, complete all as specified and directred.

M & L for applying two coats of distemper oil emulsion over one coat of priming plastered surfaces with alkali resistant priming paint over with 3mm thick wall care putty on wall complete all as specified and directed

M & L for applying one coat of oil bound distemper white or tinted on walls over and including preparation of old (Previously treated) plastered or unplastered surfaces of wall by washing, rubbing down and stopping of distempered or painted surfaces of walls complete all as specified and directed.

M & L for applying one coat of white wash on wall over and including preparing of plastered or unplastered old decorated surfaces of ceiling by brooming down or steel wire brushing, scraping down smoke soot, moulds, mass and efflorescent, salt and trading oil and greasy spouts including cornices etc. complete all as specified and directed.

M & L for two coats of cement base paint on new plastered wall surfaces after applying a coat of alkali resistant primer including preparation of surfaces complete all as specified and directed

M & L for applying one coat of cement base paint on walls over and includimng preparing of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing, scraping down smoke soot, moulds, mass and efflorescent, salt and trading oil and greasy spouts including cornices etc. complete all as specified and directed.

M&L for applying two coats of cement base paint over a coat of primer on newly plastered wall surfaces including cornices & pillasters etc as per manufacturer's specification & instruction including preparation of surface, complete all as specified and directred

M & L for appling a coat of cold bituminous primer over cleaned plastered surface @ 0.40 Kg/Sqm followed by APP modified five layer ploymeric membrane 3mm thick, minimum wt 3.50 kg/Sqm reinforced with polyester non-woven fabric (weighing not less than 150gms/Sqm ) manufactured by as per list of make in tender documents approved by GE, laid as per the manufactures instruction with side over lap of 75mm & end over lap of 100mm & tucked into the chases on vertical surfaces if required & finally finished with bituminous aluminum paint @ 0.10 Kg/Sqm over old roof/wall surface over and including 15mm thick screed bed in CM (1:3) complete all as specified and directed. Note using only course sand (Toka sand) in screed bed/plastering.

M & L for Cement concrete tiles 25cm x 25cm x 20 to 22 mm thick, with gray cement and no pigment machine pressed; set jointed and pointed in neat cement slurry over and including 15mm thick screed in CM (1:4) with and including mixing of liquid water proofing compound as per manufacture specifications, as in roof and floor tiles complete complete all as specified and directed. Note:- WPC shall be measured and paid separately.

Supply only liquid integral water proofing compound as approved by GE from list of make attached in tender documents complete all as specified and directed.

Dismantling of stone slab and tiles of any description or thickness in floor, aprons, kerbs, vertical surface etc laid dry complete all as specified and directed.

S&F 35mm thick factory made panelled shutter (two panel) plain framed with lock rail and panel of 12mm thick veneered particle board with commercial veneering on both faces conforming to IS-3097 exterior grade kiln seasoned and chemically pressure treated of second class hard wood rails and styles and the size of rail and style as per IS-1003 (Part I).

S&F for ventilators with top hung shutters including hinges with steel handle and steel peg stay complete with out glazing bars, complete all as specified and directed.

S & F MS galvanised mild wire cloth 0.56 mm nominal dia of wire and avarage width of aperture 1.18mm and fixed with tinned tacks to galvanised wire stapple complete all as specified and directed.

S & F 595x595mmx6mm thick Gypsum board laminated with PVC Sheet as in false ceiling including supply and fixing 'Tee" grid frame work made of GI sheet 0.30mm thick, bottom portion painted with cellular nitro painting, consisting angle cleats of size 25mm wide 1.6mm thick with flag fixed to RCC ceiling with dash fastener or wraping the suspending wire around the existing wooden/steel purlin/rafter for suslpending grid frame work of size 600mmx600mm suspended with 02 Nos, 1.60mm dia GI wire @ 600mm C/C on main Tee and fixed to T-grid as per manufacturer direction. The section consisting of main Tee 37mm x24mmx0.60mm thick, cross runner tee 37mmx24mmx0.60mm and. Perimeter angle 24mmx24mmx0.50mm thick shall be fixed to wall with GI screw of 40mm long @ 450mm C/C along the perimeter of wall including or wall including all as per manufacturer's instruction complete all as specified and directed.

Dismantling of AC sheets (corrugated, semi corrugated etc) sheets in roof covering including ridges complete all as specified and directed.

M&L for prepainted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550Mpa as in wall, fixed with slef tapping screws complete all as specified and directed.

S & F Pre-painted galvatume aluminium zinc coaring GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified including dismantling of old sheet. complete all as specified and directed.

S & F Factory made steel window box type using ERW hollow 'P' section comprising double frame for and including gauged and glazed Skeleton shutter jointed internally with flat iron 40x4mm complete including grill of 8mm square bars, fixed horizontally @ 10cm c/c, hinges, handle, tower bolts, stops, lugs etc. (ref CEBTZ drg). complete all as specified and directed.

All as per Srl item No. 141 But steel ventilators top hung complete all as specified and directed.

S & F Aluminium powder coated vents including provision of necessary rubber gasket for fixing glass panes etc complete all as shown in drawing No. CEBT/SK-936 sheet 1/1 available in AGE B&R-I office complete all as specified and directed. Note:- Sheet glass shall be measured and paid separately under respective item.

M & L 75mm thick, cement concrete 1:3:6, type C2 using 40mm graded crushed stone aggregate as in floors, plinth protection, paths, etc and finishing top surfaces even and smooth without using extra cement complete all as specified and directed.

M & L machine pressed precast concrete coloured interlocking paver block any shape, size and pattern, IS - 15658-2006 (Marked) of 60 mm thickness of M-35 grade with grey cement & pigment over and including 25mm thick sand cushioning complete all as specified and diretced.

Dismantling floor, hearth or wall tiling incl cement mortar bedding and rubbish off the premises complete all as specified and directed.

Dismantling of ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs/blankets any thickness, including cover fillets etc complete all as specified and directed.

S & F for vitreous china urinal, half stall type, white excluding flushing cistern but including flush pipe, and waste pipeand also including connections to flushing pipe and outpipes, bedding urinal against wall in cement mortar (1:2), securing urinal to plug with and including 60 mm long brass screws, pointing arount urinal back in cement complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and exceeding 1.5m depth for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. not exceeding 10 sqm on plan and not exceeding 1.5 m in depth and getting out in soft/losse soil & getting out complete all as specified and directed.

Material and labour for 100 mm thick cement concrete (1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base of floor, under tiles etc. complete all as specified and as directed.

Material and labour for 75 mm thick cement concrete (1:4:8), type D-2 using 40 mm graded stone aggregate as in sub base of floor, under tiles etc. complete all as specified and as directed.

Material and labour for broken bricks of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15cm thick, watered and rammed to a true surface complete all as specified & directed.

M & L for soakage well of size 1.8 mtr dia x 3.0 mtr effective depth including excavation in any type of soil, foundation in PCC 1:3:6 wall of honey combed masonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonry in CM, RCC cover slab in M-25/SFRC cover, inter connecting pipe of RCC/DWC complete filled with brick bats as per drawing as per CE BTD-827 complete all as specified & directed

M & L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested in cement concrete type D-2 1:4:8 using 20mm graded curshed stone aggregates for 150mm bore pipes complete all as specified and as directed

M & L for precast cement concrete (1:2:4) type B1 using 20mm graded stone aggregate in kerb stone, manhole covers, kitchen sink slab etc with plain fair faces including chamfers, eatherings,throating etc. and setting in mortar set in cement mortar (1:4) including neccessary form work complete all as specified and as directed.

Returning, filling in soft / loose soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick complete all as specified and directed.

Removing surplus excavated material not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Removing excavated material exceeding 250m not exceeding 500m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Supply and fixing in repair aluminium anodised powder coating of any color (thickness of powder coating not less than 50 micron) fixed type w/o sash bar, aluminium section weighting 0.55 Kg/m including necessary joining cleats, glazing clips, rubbers packing, anodised aluminium snap beading, screws etc complete all as specified and directed

M&L for complete removal of esixting surfaces of ceiling and applying two coat of white wash of old plastered ceiling surfaces complete all as specified and directed

M&L for complete removal of esixting surfaces of Wall and applying two coat of white wash of old plastered ceiling surfaces complete all as specified and directed

M&L for granite (of any type) work 20 mm thick (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 10 mm thick screed in cement mortar (1:4) and finish the surface rough to receive the tile complete all as specified and as directed. Note:- Sample of granite fornShade and type shall be approved by GE before procurement

Supply and fixing Sail-glazed stoneware drain pipes 150mm bore of grade 'A' laid in trenches and jointed etc. complete all as specified and directed.

Supply and fixing vitreous china (white) squatting pan 'Orissa' pattern, white, size 580 x 440 x 260mm, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flush pipe, anti-symphonic pipe etc including making good to floor and including trap set in including lime concrete complete all as specified and directed.

Supply and fixing 10 Liters capacity, PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Supply and fixing vitreous china wash hand basin, white, flat back, fanncy type, size 550 x 400mm including cast iron cantilever bracket 32mm dia brass waste coupling, waste fitting and union complete all as specified and directed.

Taking down carefully existing unserviceable Aluminium/copper point wiring (light, fan, socket) complete including removal of unserviceable fittings such as switches, sockets, pendants, holder, light fittings, call bells, bell push, ceiling roses, etc and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and directed.

M & L for point wiring for one light / fan point controlled by one switch with 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FR-LSH in and including concealed PVC conduit 20 mm dia heavy duty ISI marked, steel terminal sunken boxes and 3 mm thick phenolic laminated sheet top cover for sunken boxes flush to surface for one light point/fan point, controlled by one switch on the same board with other switch or independent including PVC insulated unsheathed 1.5 Sqmm copper conductor cable FR-LSH connected to common earth dolly complete including cutting, chasing the surface and then making good the same in CM (1:3) complete all as specified and directed .(Note :- Switches, sockets etc shall be measured and paid for separately under appropriate items of BOQ ).

All as per srl item No. 169 (here-in-before) but one light/fan/exhaust fan point controlled by 5 Amps one way switch

All as per srl item No. 169 (here-in-before) but socket 3 pin 5 Amp 230 volt flush type on same board

All as per srl item No. 169 (here-in-before) but for one socket point out let 3 pin 5 Amp in independent board.

All as per item No. 169 hear in befor but with two run of signal core 2.5 Sqmm (nominal area) PVC insulated, unsheathed multi stranded copper conductor cable FR-LSH for 15 Amps per point including one run of single core 2.5 Sqmm (nominal area) PVC insulated, unsheathed multi stranded copper conductor cable FR-LSH as earth continuity conductor complete all as specified and as directed.

M & L for point wiring for with two run of 1.5 Sqmm (nominal area) PVC insulated, unsheathed multi strand copper conductor cable FR-LSH in and including surface mounted stove enamelled steel conduit suitable dia medium grade ISI marked with one run of PVC insulated unsheathed 1.5 Sqmm copper conductor cable FR-LSH connected to common earth dolly complete all as specified and directed .(Note :- Rotary Switches, junction box etc shall be measured and paid for separately under appropriate items of BOQ).

S & F switch flame proof/weather proof rotary type switch with termination box in LM6, 16A double pole 250V complete all as specified and directed .

S & F switch flame proof/weather proof junction box in 4 way LM6 complete all as specified and directed .

S&F Switch piano, flush type single pole, one way 5 Amp complete all as specified and directed .

S&F Switch piano, flush type single pole, one way 15/16Amp complete all as specified and directed .

S&F Socket outlet 2 in 1, 3 pin, 5 Amp complete all as specified and directed .

S&F Socket outlet 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed .

S&F Socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type complete all as specified and directed .

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. complete all as specified and directed .

S&F Ceiling rose, 3 terminal PVC/polycarbonate, suitable for 230 V, AC, 50 Hz supply complete all as specified and directed .

S & F angle lamp holder polycarbonate type with back plate complete all as specified and directed .

S&F LED 9W Lamp base B-22complete complete all as specified and directed.

S&F sheet metal encloser double door 4 way SPN 240V ISI marked IP- 43 complete with neutral and earth link and bus bar complete made out of CRCA steel sheet Factory made including blanking plate for unused module including taking down old DB complete all as specified and directed

S&F in repalcementvsheet metal encloser double door 12 way SPN 240V ISI marked IP- 43 complete with neutral and earth link and bus bar complete made out of CRCA steel sheet Factory made including blanking plate for unused module complete all as specified and directed

S&F MCB 6-32 Amp 240V SP 10 KA ‘C’ series complete all as specified and directed

S&F MCB 20-25 Amp 240V SPN 10 KA ‘C’ series complete all as specified and directed

S&F MCB 40-63 Amp 240V SPN 10 KA ‘C’ series complete all as specified and directed

S & F LED light fitting 1x20 watt, 230 V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed.

S & F LED light fitting mirror type with hogh out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in repair LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrossion resistant complete with IP 65/66 protection, including fixing with GI/MS bracket made out of suitable size of light grade tube of 40mm bore with suitable length bent to shape with 02 sets of MS clamps made out of minimum 3 mm MS flat iron with suitable bolt and nuts complete with making connection complete allas specified and directed

M & L for earthing with galvanized steel plate electrode 600 x 600 mm x 6.3 mm size directly burried in ground vertically to earth pit not less than 2.25 meter deep below normal ground level with top edge of the earth plate not less than 1.5 m below normal ground level surrounded with coal dust and common salt filling in alternative layers of 15 cm thick Each connected to and including GI earth wire 4 mm dia by means of nuts, bolts, check nuts & washers etc connecting to earthing test point, main switch board and including 15 mm dia GI pipe light grade for protection of earth lead from earth plate to distribution board and 20 mm dia GI pipe medium grade connected with funnel having wire mess for watering purpose including necessary excavation and earth work, PCC (1:2:4) type B-1 (using stone aggregates) for earthing pit, 10mm thick cast iron cover with angle iron frame all as specified and shown in electrical plate No 3 of SSR Part-I and testing on completion including replacement of old unserviceable.

M & L for earthing with copper earth plate electrode 600 x 600 mm x 6.3 mm size directly burried in ground vertically to earth pit not less than 2.25 meter deep below normal ground level with top edge of the earth plate not less than 1.5 m below normal ground level surrounded with coal dust and common salt filling in alternative layers of 15 cm thick Each connected to and including GI earth wire 4 mm dia by means of nuts, bolts, check nuts & washers etc connecting to earthing test point, main switch board and including 15 mm dia GI pipe light grade for protection of earth lead from earth plate to distribution board and 20 mm dia GI pipe medium grade connected with funnel having wire mess for watering purpose including necessary excavation and earth work, PCC (1:2:4) type B-1 (using stone aggregates) for earthing pit, 10mm thick cast iron cover with angle iron frame all as specified and shown in electrical plate No 3 of SSR Part-I and testing on completion including replacement of old unserviceable.

S & F in repalcement flameproof/weatherproof DB SPN 6 way LM-6 CMRI certified made out of cast aluminium alloy confirming to IS/IEC 60079-1:2007 with ON-OFF rotary switches and LED indication lamp mopunted extenally for each circuit duly painted with anti corrosive epoxy powder coated paint including 01 No MCB SP 32A as incomer and 3 No MCB SP 6A as outgoing complete fixing on wall recessed or surface mounted complete all as specified and directed.

S & F LED light fitting 1 x 18 watt flame proof, CMRI certified recommended for gas/vapor group of IIA & IIIB, zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and directed.

Taking down carefully existing ceiling fans 1200/1400mm sweep from site, deposit safely to E/M yard and refixing the fan to respective place as and when directed by Engr-in-charge including carrying out minor repair like cleaning all the components of fan, including replacement of nuts, bolts, split pin, rubber reel, capacitor 2.5mfd & including 3 core PVC insulated PVC sheathed copper conductor flexible cable 1.5 sqmm from ceiling rose to fan and painting the fans complete all as specified and directed.

M & L for Air termination, single pointed, copper rod 12mm and 300mm long complete all as specified and directed.

M & L for Copper strip 20 x 3.15mm with saddles and fixing screw etc. for roof conductors and down conductors above ground complete all as specified and directed.

M & L for test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. Head screw complete all as specified and directed.

S & F exhaust fan 300mm sweep steel body complete with blades, frame and louvers suitable for 230 volts, 50 Hz, AC supply complete all as specified and directed.

Note:- All debris obtained from dismintling, demolition and taking down (Exept credited to contractor) shall be desposed off out side MOD land and charges, if any, as incurred in civil area as per their regulator shall be deemed to be including in quoted rates. No extra claim on this account shall be admissble.

Note:- Net contract sum shall be calculated after deduction of Sch of credit.

Ajay Enterprises

M/S BHAGWATI CONSTRUCTION COMPANY

M/s Kamal Constructions

M/S VIAJY BUILDERS & DEVELOPERS

SHARDA ENTERPRIES