REPAIR TO STREET LIGHT, ELECTRICAL PANEL, DG SET AND ELECTRIC CABLE AT AIR FORCE STATION HIGH GROUNDS UNDER GE (AF) CHANDIGARH

Amount

EXTERNAL ELECTRIFICATION

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep for laying/taking out of cables and foundation of poles etc. and getting out, complete all as specified and directed.

All as per item No. 1.01 but exc 1.5 metre and not exceeding 3.0 metre deep , complete all as specified and directed.

Returning, filling in trenches (soil), including spreading, leveling and well ramming in layers not exceeding 25 cm thick, complete all as specified and directed.

Removal of surplus excavated soil to a distance not exceeding 50metre and depositing where directed at a level not exceeding 1.5metre above the starting point, complete all as specified and directed.

Material and labour, sand cushioning with a layer of dry river sand, 80mm thick before laying of cable and 150mm thick (punned down to 100mm thick) after laying of cables, in trenches/ducts, complete all as specified and directed. Note : Punned down thickness (overall 18cm), shall be considered for measurement and payment.

Material and labour, locally available, sub class `B’ bricks (old size), laid flat and dry perpendicular to the direction of cable adjacent to each other, in trenches over the cable for protection, complete all as specified and directed.

Relaying only well burnt brick sub class 'B' old size brick laid dry in trenches with width equal to the length of the brick , complete all as specified and directed. Note:- Bricks are to be reused retrived during the cable taking out

Taking out / down old existing LT 1100volt grade cables, size 10Sqmm, aluminium conductor 2core, XLPE/ PLCA/ PVC, armoured, laid in trenches, including bricks for protection, sand cushioning and stacking, removal to store for re-use or for credit, complete all as specified and directed Note : Excavation shall be measured and paid for separately

All as per Serial Item No. 1.08 here-in-before but 16Sqmm 2Core size

All as per Serial Item No. 1.08 here-in-before but 16Sqmm 4Core size

All as per Serial Item No. 1.08 here-in-before but 35Sqmm 3.5Core size

All as per Serial Item No. 1.08 here-in-before but 50Sqmm 3.5Core size

All as per Serial Item No. 1.08 here-in-before but 95Sqmm 3.5Core size

All as per Serial Item No. 1.08 here-in-before but 150Sqmm 3.5Core size

All as per Serial Item No. 1.08 here-in-before but HT cable 3 core 95Sqmm size

Relaying, jointing, testing and commissioning, already taken out existing LT under ground cables XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured electric power cable (heavy duty) with aluminium conductor cross sectional area 10Sqmm 2 core, 1100 volts grade, laid in trenches, along poles or passing through pipes or laid under floor or through/on walls etc, complete all as specified and directed.

All as per Serial Item No. 1.16 here-in-before but 16Sqmm 2Core size

All as per Serial Item No. 1.16 here-in-before but 16Sqmm 4Core size

All as per Serial Item No. 1.16 here-in-before but 35Sqmm 3.5Core size

All as per Serial Item No. 1.16 here-in-before but 50Sqmm 3.5Core size

All as per Serial Item No. 1.16 here-in-before but 95Sqmm 3.5Core size

All as per Serial Item No. 1.16 here-in-before but 150Sqmm 3.5Core size

Supply, laying, jointing, testing and commissioning of Low Tension (LT) XLPE insulated and armoured, heavy duty, electric power cable, cross sectional area 10Sqmm 2 core aluminum conductor 1100volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: Returning filling & removal of earth, sand cushioning and bricks for protection of cable shall be measured and paid separately.

All as per Serial Item No. 1.23 here-in-before but 16Sqmm 2Core size

All as per Serial Item No. 1.23 here-in-before but 16Sqmm 4Core size

All as per Serial Item No. 1.23 here-in-before but 35Sqmm 3.5Core size

All as per Serial Item No. 1.23 here-in-before but 50Sqmm 3.5Core size

All as per Serial Item No. 1.23 here-in-before but 95Sqmm 3.5Core size

All as per Serial Item No. 1.23 here-in-before but 150Sqmm 3.5Core size

Supply, laying, jointing, testing and commissioning of High Tension (HT) XLPE insulated , screened, PVC bedded, galvanized steel strip or wire armoured, armoured, heavy duty, electric power cable, cross sectional area 95Sqmm 3core aluminum conductor 11000volts grade under ground cable including both side connection with cable lugs etc, laid in trenches, along poles or passing through pipes or laid under floor or through walls etc, complete all as specified and as directed. Note: Returning filling earth work, sand cushioning and bricks for protection of cable shall be measured and paid separately.

Supply, jointing & testing, indoor end termination joint kit (Heat shrinkable) complete with jointing material and accessories suitable for 3wire, 11KV (Earthed) grade, HT, underground XLPE insulated armoured aluminium conductor cable, 3core, 95Sqmm size cable, complete all as specified and directed.

Supply, jointing & testing, outdoor end termination joint kit (Heat shrinkable) complete with jointing material and accessories suitable for 3wire, 11KV (Earthed) grade, HT, underground XLPE insulated armored aluminium conductor cable, 3core, 95Sqmm size cable, complete all as specified and directed.

Supply, jointing & testing, straight through joint kit (Heat shrinkable) complete with jointing material and accessories suitable for 3wire, 11KV (Earthed) grade, HT, underground XLPE insulated armoured aluminium conductor, 3core, 95Sqmm size cable, complete all as specified and directed.

Supply and laying / fixing , GI pipe light grade 100mm dia bore for cable protection fixed to pole/wall or laid under floor/road/pavement, including flat iron clamp, nut, bolt, wahser etc of required size and taking out old & removal, complete all as specified and directed. Note: Boring of holes under road etc. shall be measured and paid separately.

Supply and laying / fixing , GI pipe light grade 80mm dia bore for cable protection fixed to pole/wall or laid under floor/road/pavement, including flat iron clamp, nut, bolt, wahser etc of required size and taking out old & removal, complete all as specified and directed. Note: Boring of holes under road etc. shall be measured and paid separately.

Supply and laying / fixing , GI pipe light grade 50mm dia bore for cable protection fixed to pole/wall or laid under floor/road/pavement, including flat iron clamp, nut, bolt, wahser etc of required size and taking out old & removal, complete all as specified and directed. Note: Boring of holes under road etc. shall be measured and paid separately.

Material and labour for switch air break, gang operated triple pole ,mechanically operated, mounted on 12 insulators including drop out insulators including 3 nos barrel type drop out fuses and steel frame with operating mechanism worked from ground level with 25mm light grade GI tubing for current rating upto 400 amps,11000 volt including taking down old and removal complete all as specified and directed.

Material and labour for lightening arrestor high tension ,expulsion type complete with all fittings, transmission class ,discharge capacity 65 kilo amp ,suitable for 11000 volt grade system fixed in position including disconnecting and taking down old and removal complete all as specified and directed.

Supply and filling of transformer oil of superior quality having di-electric strength not less than 40 KV at 4.0mm gap, ISI marked and filling into transformers and other equipments installed at various locations, after taking out old unserviceable oil, complete all as specified and directed. Note:- (i) Transformer oil will be supplied in duly filled in sealed drums. (ii) Necessary test certificate provided from authorised lab or state electricity board test lab.

Supply and fixing in replacement the under mentioned spare/parts of transformer capacity from 50 KVA to 400KVA, complete all as specified and directed.

(a) Air breather assembly with silica gel

(b) HT side procelain bush 11KV (Set of 03) with brass studs, nuts & washers, rubber gasket etc

(c) LT side procelain bush 415V upto 100KVA transformer (Set of 04) with brass studs, nuts & washers, rubber gasket etc

(d) LT side procelain bush 415V upto 200KVA - 250KVA transformer (Set of 04) with brass studs, nuts & washers, rubber gasket etc

(e) LT side procelain bush 415V upto 300KVA - 400KVA transformer (Set of 04) with brass studs, nuts & washers, rubber gasket etc

Dismantling/Strip opening of the HT VCB 11KV 400 Amps for calibration, repairing, preventative maintenance, servicing including replacement of worn out parts to make it fully functional, reassembling the same after repair, installation to its original position, connection input/output supply, testing to its full load capacity and all other relevant tests as per IE/IS rules, complete all as specified and directed. Note: Spare parts required for repair/replacement shall be maeasured and paid separately.

Supply and fixing in replacement under mentioned spare/parts 11KV, 400 Amps HT VCB, any model/type of make :- Kirloskar/Crompton complete all as specified and directed.

Supply only, PT trannsformer of 11KV/110V, totally ennclosed, sealed and stamped, epoxy filled, heavy duty, suitable for 11 KV, 400 Amps HT VCB, complete all as specified and directed.

Supply only, Micro process based relay heavy duty, suitable for 11 KV 400Amps HT VCB, complete all as specified and directed.

Supply only, vaccum interruptor for VCB, complete all as specified and directed.

Supply only, trolly insulator for mounting vaccum interruptor for VCB, complete all as specified and directed.

Supply only, epoxy fibre base plate for interruptor, complete all as specified and directed.

Supply only, epoxy insulator for bus bar supports, complete all as specified and directed.

Supply and fix, finger moving contact (Made up of six, each male and female, fingers), spring loaded, heavy duty, suitable for 11KV, 400Amp, HT VCB, complete all as specified and directed.

Supply only, Current Transformer (CTs) of CTR 50-25 / 5Amps, totally enclosed, sealed and stamped, epxoy filled, heavy duty, suitable for 11 KV 400 Amps HT VCB, complete all as specified and directed.

Servicing of all relays, Battary Bank, and checking calibration and time gap, adjustment of earth fault relay, over current relay and reconnecting all the relays to their respective circuits and locations, of HT VCB 11 KV 400 Amps, and testing on completion to the entire satisfaction of Engr-In-Charge, complete all as specified and directed.

Supply and fix, in replacement MCCB, four pole, 400Amps, 415 volts, 50 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Supply and fix, in replacement MCCB, four pole, 250Amps, 415 volts, 35 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Supply and fix, in replacement MCCB, four pole, 200Amps, 415 volts, 35 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Supply and fix, in replacement MCCB, four pole, 160Amps, 415 volts, 25 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Supply and fix, in replacement MCCB, three pole, 250Amps, 415 volts, 35 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Supply and fix, in replacement MCCB, three pole, 200Amps, 415 volts, 25 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Supply and fix, in replacement MCCB, three pole, 160Amps, 415 volts, 25 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Supply and fix, in replacement MCCB, three pole, 125Amps, 415 volts, 25 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Supply and fix, in replacement MCCB, three pole, 63Amps, 415 volts, 16 KA, 50Hz , with adjustable thermal and magnetic release, complete with extension links and making connection in panel board, complete all as specified and directed.

Demolition of cement concrete (unreinforcement) as in coping /foundation of poles and other similar work including removal of rubbish outside MOD land complete all as specified.

Material and Labour for PCC 1:2:4 type B-1 using 20mm graded stone aggregate for coping incuding necessary form work, complete all as specified and directed.

Material and Labour for PCC 1:4:8 type D-2 using 40mm graded stone aggregate for foundation filling, complete all as specified and directed.

Material and labour, Cross arms, bracing, supports, clamps and back plates, fabricated from structural steel section Fe-290 grade E-165 quality including nuts, bolts, washers, and welding, bending cold or hot, drilling holes for bolts, in any shape or size as directed including two coats of alminium paint over a coat of red oxide primer including dismantling ,complete all as specified and directed.

Material and labour, painting two coats of aluminium paint to steel tubular poles of any description (external surface only) 9m long, including MS cross arms etc making of 5 strips of width 300mm each (03 Nos Sky blue and 2 No. white) writing pole No. with black paint with letters/figures in girth 3 inch, including preparation of old painted surface, complete all as specified and directed.

Material and labour, painting two coats of aluminium paint to MS cross arms only fitted with PCC poles of any description and making of 5 strips of width 300mm each (03 Nos Sky blue and 2 No. white) writing pole No. with black paint with letters/figures in girth 3 inch, including preparation of old painted surface, complete all as specified and directed.

Material and labour, applying one coat of synthetic enamel paint on old steel surfaces over 10cm width or girth, including preparation of steel surface, complete all as specified and directed.

Supply and fix in replacement chequered plate of any thickness as in duct cover, complete all as specified and directed.

Supply and fix cable jointing kit for 1.1 KV grade cable for straight through joint complete with jointing material heat shrink type and accessories suitable for 25 Sqmm to 50Sqmm 3.5 core indoor/outdoor type, complete all as specified and directed.

All as per Serial Item No. 1.74 here-in-before but 70Sqmm to 95Sqmm 3.5 core.

All as per Serial Item No. 1.74 here-in-before but 120Sqmm to 150Sqmm 3.5 core.

All as per Serial Item No. 1.74 here-in-before but 185Sqmm to 300Sqmm 3.5 core.

Supply and fix in replacement factory made indoor type bus bar chamber box, wall mounted type, made out of 2mm thick CRCA sheet powder coated, single door of size 60cmx60cmx30cm having insulated copper bus of capacity 200Amps three phase installed on porcelain insulator, complete all as specified and directed.

Supply, installing, testing and commissioning, factory made & tested including CPRI approved, LT Feeder pillar box outdoor type of size 90cmx60cmx30cm, suitable for 415Volts 3phase 4wire 50Hz AC supply having bus bar chamber with insulated copper bus bar 200amp rating installed on pocelain insulators, The panel shall be dust and vermin proof, IP65 protection & made out of MS CRCA quality sheet 3.15mm thick, and 50mm x 50mm x 6mm angle iron base frame with 04 Nos legs 75cm long made out of MS angle iron of size 50mm x 50mm x 6mm, legs embedded in PCC (1:2:4) having bottom of the panel at height of 45cm above ground level, duly powder coated finish over one coat of red oxide primer outside and two coats of red oxide primer inside and front and back openable type with aprons for cable entry with double door shutter and locking arragements, internal wiring with PVC insulated solid copper conductor FRLS cable, IS-694 marked of adequate size, complete all as specified and directed.

Supply and fix in replacement, on-load change over switch four pole, 200Amp in steel sheet enclosure, complete all as specified and directed.

Supply and fix in replacement, on-load change over switch four pole, 400Amp in steel sheet enclosure, complete all as specified and directed.

DG SET REPAIRS

Maintenance of DG set of any make, type, model as per set norms of the original manufacturer set and by the authorised rep of the company after unscrewing nut, bolts, screws etc. for servicing, maintenance, tigthtening, adjustment & cleaning of all moving and stationary parts of DG set, complete and segregating the parts for repair/ refixing/ replacing of capacity 10KVA installed at IMMOLS , complete all as specified and directed. Make of DG sets :- kirloskar/Crompton Greaves/Ruston/Ashok Leyland Note: The quoted rate includes the following: (a) Taking down of unserviceable parts. (b) Any minor repair, replacement of minor parts such as screws, gasket, nuts, bolts, washers, cleaning & greasing etc. of DG set parts. (c) Defective parts/ engine oil to be replaced will be measured & paid separately under supply only item as apended below.

All as per Serial Item No. 2.01 here-in-before but capacity 30 KVA installed at Sewage pump house

All as per Serial Item No. 2.01 here-in-before but capacity 35 KVA installed at Pump house No. 5 & TOP

All as per Serial Item No. 2.01 here-in-before but capacity 40 KVA installed at Pump house No. 5 & 6

All as per Serial Item No. 2.01 here-in-before but capacity 63 KVA installed at TRU & TOP

All as per Serial Item No. 2.01 here-in-before but capacity 75KVA installed at AFNET

All as per Serial Item No. 2.01 here-in-before but capacity 82.5KVA installed at MIG-29 complex

All as per Serial Item No. 2.01 here-in-before but capacity 400KVA installed at Avionics lab complex

Supply only under mentioned spare/parts suitable for the DG set complete all as specified and directed:-

Primary fuel filter element for DG set capacity 10KVA

Primary fuel filter element for DG set capacity 30KVA

Primary fuel filter element for DG set capacity 35KVA

Primary fuel filter element for DG set capacity 40KVA

Primary fuel filter element for DG set capacity 63KVA

Primary fuel filter element for DG set capacity 75KVA

Primary fuel filter element for DG set capacity 82.5KVA

Primary fuel filter element for DG set capacity 400KVA

Secondry fuel filter element for DG set capacity 10KVA

Secondry fuel filter element for DG set capacity 30KVA

Secondry fuel filter element for DG set capacity 35KVA

Secondry fuel filter element for DG set capacity 40KVA

Secondry fuel filter element for DG set capacity 63KVA

Secondry fuel filter element for DG set capacity 75KVA

Secondry fuel filter element for DG set capacity 82.5KVA

Secondry fuel filter element for DG set capacity 400KVA

Air filter element for DG set capacity 10KVA

Air filter element for DG set capacity 30KVA

Air filter element for DG set capacity 35KVA

Air filter element for DG set capacity 40KVA

Air filter element for DG set capacity 63KVA

Air filter element for DG set capacity 75KVA

Air filter element for DG set capacity 82.5KVA

Air filter element for DG set capacity 400KVA

Oil filter element for DG set capacity 10KVA

Oil filter element for DG set capacity 30KVA

Oil filter element for DG set capacity 35KVA

Oil filter element for DG set capacity 40KVA

Oil filter element for DG set capacity 63KVA

Oil filter element for DG set capacity 75KVA

Oil filter element for DG set capacity 82.5KVA

Oil filter element for DG set capacity 400KVA

Water hose pipe set complete for DG set capacity 10KVA

Water hose pipe set complete for DG set capacity 30KVA

Water hose pipe set complete for DG set capacity 35KVA

Water hose pipe set complete for DG set capacity 40KVA

Water hose pipe set complete for DG set capacity 63KVA

Water hose pipe set complete for DG set capacity 75KVA

Water hose pipe set complete for DG set capacity 82.5KVA

Water hose pipe set complete for DG set capacity 400KVA

Fuel and oil hose pipe set complete for DG set capacity 10KVA

Fuel and oil hose pipe set complete for DG set capacity 30KVA

Fuel and oil hose pipe set complete for DG set capacity 35KVA

Fuel and oil hose pipe set complete for DG set capacity 40KVA

Fuel and oil hose pipe set complete for DG set capacity 63KVA

Fuel and oil hose pipe set complete for DG set capacity 75KVA

Fuel and oil hose pipe set complete for DG set capacity 82.5KVA

Fuel and oil hose pipe set complete for DG set capacity 400KVA

Material and labour for taking out radiator and repairing/brazing to make it leakage free, cleaning and re-fixing the radiator including testing for DG set capacity 10KVA to 40KVA, complete all as specified and directed.

All as per item No. 2.58 here-in-before but DG set capacity 63KVA to 82.5KVA complete all as specified and directed.

All as per item No. 2.58 here-in-before but DG set capacity 400KVA complete all as specified and directed.

Supply only lubricant oil (Engine oil) SAE30 (Make as recommended by the manufacturer of DG set and as approved)

Supply, install, connecting and testing in replacement maintenance free batteries, 12 Volts, 180AH, complete all as specified and directed.

Supply, install, connecting and testing in replacement maintenance free batteries, 12 Volts, 92AH, complete all as specified and directed.

Supply and fix, battery lead not less than 1.5mtr long, made out of 50Sqmm copper cable with terminal of brass with marking (+)/(-) and fixing in position and testing, including taking down and removal, complete all as specified and directed.

Supply and filling, engine coolant in radiators of DG sets as per DG set manufacturer's recommendations at different locations, brought at site in sealed packets, complete all as specified and directed.

Maintenance, repair, servicing and calibration of automatic mains failure panel, DC & 415/440 volt AC supply operated system by locating faults and replacement of unserviceable parts and components for DG set 10KVA to 400KVA and testing on completion , complete all as specified and directed. Make of DG sets:- Kirloskar/Crompton Greaves/Ruston/Ashok Leyland Note: The quoted rate includes the following: (a) Taking down of unserviceable parts. (b) Any minor repair, replacement of minor parts such as screws, gasket, nuts, bolts, washers, cleaning & greasing etc. of DG set parts. (c) Defective parts/ engine oil to be replaced will be measured & paid separately under supply only

Repair of faulty worn out control wiring DC/AC for engine starting and off, with adequate and suitable size copper conductor wire, connected with proper copper lugs & terminals through protection pipe/casing, complete all as specified and directed.

Repair of worn out/faulty internal wiring of controls and timers, indicating/measuring instruments through various control fuses and relays with suitable and adequate size of copper conductor wire, connected with suitable copper lugs and terminals, complete all as specified and directed.

Replacement of worn out small control fuses, indicating lamps, various type of copper lugs, thimbles terminals all as deemed necessary or directed including minor spare parts and components in order to make system serviceable and perfectly in working order , complete all as specified and directed.

Material and labour for repairing battery charging dynamo including replacing work out/unserviceable spares upto the capacity of 82.5 KVA, complete all as specified and directed.

Material and labour for repairing battery charging dynamo including replacing work out/unserviceable spares upto the capacity of 400KVA, complete all as specified and directed.

Material and labour for repairing self starter including replacing work out/unserviceable spares upto the capacity of 82.5 KVA, complete all as specified and directed.

Material and labour for repairing self starter including replacing work out/unserviceable spares upto the capacity of 400 KVA, complete all as specified and directed.

Material and labour for replacing the unserviceable AVR of DG sets upto the capacity 82.5 KVA and testing, complete all as specified and directed.

Material and labour for replacing the unserviceable AVR of DG sets upto the capacity 400 KVA and testing, complete all as specified and directed.

Power contractor 3 pole 200 Amps 415 volts operating coil voltage 230 Volts, complete all as specified and directed. Make:- Havells/L&T/ABB

Power contractor 3 pole 315 Amps 415 volts operating coil voltage 230 Volts, complete all as specified and directed. Make:- Havells/L&T/ABB

Power contractor 3 pole 400 Amps 415 volts operating coil voltage 230 Volts, complete all as specified and directed. Make:- Havells/L&T/ABB

Material and labour for repair to unserviceable street/security light fittings of LED of any wattage and size by taking down from poles/buildings after disconnecting the electric connection, replacing the unserviceable driver, PVC connector etc, cleaning and refixing the light fittings at its original position after rectifying the defects and connecting to street light feeder including testing, complete all as specified and directed. Note:- (i) Replacement of parts like driver etc will be measured and paid separately.

Taking down the existing light fittings multi mounting brackets from high mast pole/structure for repairs/replacing the defective parts and refixing the same in original position after carrying out necessary repair/replacement of parts i.e. unserviciable ignitor, ballast, capacitor from control gear box , complete all as specified and directed.

PVC insulated stranded aluminium conductor, 1100 volts grade heavy duty cable of size 2.5Sqmm 2 core (from junction box to street light fitting mounted on steel tubular/PCC pole) including taking down existing unserviceable cable, complete all as specifie

Supply only open construction ballast copper wounded for 400 watts HPSV/MH lamps, complete all as specifie

Supply only metal halide lamp 400 watts, 230 volts, single/double ended tubular/ballon type, complete all as specifie

Supply only electronic driver suitable for LED street/flood light of capacity upto 90W, complete all as specifie

Supply and fixing in replacement LED street light fitting 60W, AC 240 volts 50Hz powder coated pressure die cast aluminium housing power LED with heat resistant toughened glass IP 66 , complete all as specified and directed. Make:- Havells Cat Part No. ENDURAPEARLPLUSSL60WLED757SASYTOPC or Equivalent in Appendix 'B'.

Supply and fixing in replacement LED street light fitting 25W, AC 240 volts 50Hz powder coated pressure die cast aluminium housing power LED with heat resistant toughened glass IP 66 , complete all as specified and directed. Make:- Havells Cat Part No. ENDURAPEARLSL25WLED757SASYTOPC or Equivalent in Appendix 'B'.

Supply and fixing in replacement LED flood light fitting 150W, AC 240 volts 50Hz powder coated pressure die cast aluminium housing power LED with heat resistant toughened glass IP 66 , complete all as specified and directed. Make:- Havells Cat Part No. JETAIRISFLS 150WLED757PSYMLTG or Equivalent in Appendix 'B'.

Supply and fixing LED post top latern 25 Watts comprising of single piece pressure die cast aluminium alloy housing powder coated cone round milkey post top, complete prewired fixed to pole/wall bracket and connected with flexible copper conductor cable of size1Sqmm three core suitable length, including taking down old fitting, complete all as specified and directed. Make:- Havells Cat Part No. CORALPT25WLED757PSYMTOPC or Equivalent in Appendix 'B'.

Supply and fix, junction box of size 30cmx20cmx15cm, outdoor type, made out of mild steel CRCA sheet 2mm thick duly painted with synthetic enamel paint (internally & externally) over a coat of red oxide primer and provision of hinged door with locking arrangement & fixing with steel tubular poles with 2Nos. MS flat iron clamps 25mmx3mm made to shape with nuts, bolts, washers etc. and provision of aluminium bus bar 100Amps-04Nos & MCB SPN 6Amp, 10 KA, 240volts, fixed in repair, complete all as specified and directed.

Supply and fix, junction box of size 30cmx20cmx15cm, outdoor type, made out of mild steel CRCA sheet 2mm thick duly painted with synthetic enamel paint (internally & externally) over a coat of red oxide primer and provision of hinged door with locking arrangement & fixing with steel tubular poles with 2Nos. MS flat iron clamps 25mmx3mm made to shape with nuts, bolts, washers etc. and provision of aluminium bus bar 100Amps-02Nos & MCB SPN 6Amp, 10 KA, 240volts, fixed in repair, complete all as specified and directed.

Supply and fixing LED Bollard 8Watts comprising of pressure die cast aluminium alloy housing powder coated pyramid Square top bollard 600mm , complete prewired fixed to pole/wall bracket and connected with flexible copper conductor cable of size 1Sqmm three core suitable length, including taking down old fitting, complete all as specified and directed. Make:- Havells Cat Part No. CONEBL8WLED857SSYMTOPC or Equivalent in Appendix 'B'.

Supply and fixing water pump for DG set suitable for capacity upto 82.5KVA, including dismantling and refixing accessories, complete all as specified and directed.

Supply and fixing in replacement, fully automatic battery charger suitable for 12V battery capacity upto 180AH having ammeter and charge cut option, complete all as specified and directed.

Note: The Total amount shall subject to adjustment of credit of Rs.60440.00 for old Materials as per Schedule of Credit

M/S BALWINDER SINGH