Development of Facade Lighting Works at Bharat Mata Mandir, Durga Mandir, Kaal Bhairav Mandir, Sankat Mochan Mandir, Annapurna Mandir, Assi Ghat, Panch Ganga Ghat, Dashashwamedh Ghat And Other Major Tourist Places/Monuments of Varanasi.

SITC of high quality long through mono color wash light, Protection Rating : IP68, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012"/"IS 10322 (Part 5/Sec 5): 2013" and having CE certificate/Test certificates from National Accreditation Board for Testing and Calibration Laboratories/Government Labs against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embosed in the die cast. Power consumption : 50W, CCT : 1800K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver or AC 110-230V, 50Hz, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, IP68, NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP68 connector having the length >300mm.(Including TNP & Good for use.). The allowed tolerance shall be ±5%.Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.

SITC of high quality long through mono color wash light, Protection Rating : IP68, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" /"IS 10322 (Part 5/Sec 5): 2013" and having CE certificate/Test certificates from National Accreditation Board for Testing and Calibration Laboratories/Government Labs against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights having the rotation degrees embosed in the die cast. Power consumption : 100W, CCT : 1800K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver or AC 110-230V, 50Hz, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, IP68, NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP68 connector having the length >300mm.(Including TNP & Good for use.) The allowed tolerance shall be ±5%. Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I. Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.

SITC of 17W Mono color Projector Spot light, Protection Rating : IP68, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" /"IS 10322 (Part 5/Sec 5): 2013" and having CE certificate/Test certificates from National Accreditation Board for Testing and Calibration Laboratories/Government Labs against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 17W, CCT : 1800K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V(External Driver) or AC 110-230V, 50Hz. Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Glare : Specially designed glare free round shape 360 deg / 3 unit. Focussing area/LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic & glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3 Mtr. Toughened transparent glass having the IK protection up to IK08 sealed above the glare free unit. Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, IP68, HV Certificates from NABL Acrediated laboratory. The allowed tolerance shall be ±5%. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. (Including TNP & Good for use.) Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.

SITC of 10W Mono color Projector Spot light, Protection Rating : IP68, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" /"IS 10322 (Part 5/Sec 5): 2013" and having CE certificate/Test certificates from National Accreditation Board for Testing and Calibration Laboratories/Government Labs against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable wall mount yoke arrangements for fixing the lights. Power consumption : 10W, CCT : 1800K, (as per the design approval) Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in color mixing applications. Power Input : DC 24V(External Driver) or AC 110-230V, 50Hz. Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Glare : Specially designed glare free round shape 360 deg / 3 unit. Focussing area/LED will be kept 90 Deg perpendicular below the glare free optic. Size of the LED optic & glare unit must be equal or +/-2% higher to achieve the maximum intensity and less glare. This additional arrangement can be fixed or removed on the application. Glare free optical design for human viewing angle from a distance within 2-3 Mtr. Toughened transparent glass having the IK protection up to IK08 sealed above the glare free unit. Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, IP68, HV Certificates from NABL Acrediated laboratory. The allowed tolerance shall be ±5%.LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. (Including TNP & Good for use).The allowed tolerance shall be ±5%. Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.

SITC of high quality long through mono color Linear wash light, Protection Rating : IP68, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" /"IS 10322 (Part 5/Sec 5): 2013" and having CE certificate/Test certificates from National Accreditation Board for Testing and Calibration Laboratories/Government Labs against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights. Power consumption : 36W, CCT : 1800K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver or AC 110-230V, 50Hz, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, IP68, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP68 connector having the length >300mm.(Including TNP & Good for use.) The allowed tolerance shall be ±5%. Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.

SITC of high quality long through mono color Linear wash light, Protection Rating : IP68, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" /"IS 10322 (Part 5/Sec 5): 2013" and having CE certificate/Test certificates from National Accreditation Board for Testing and Calibration Laboratories/Government Labs against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights. Power consumption : 60W, CCT : 1800K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver or AC 110-230V, 50Hz, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, IP68, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP68 connector having the length >300mm.(Including TNP & Good for use.) The allowed tolerance shall be ±5%. Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.

SITC of high quality long through mono color Linear wash light, Protection Rating : IP68, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" /"IS 10322 (Part 5/Sec 5): 2013" and having CE certificate/Test certificates from National Accreditation Board for Testing and Calibration Laboratories/Government Labs against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights. Power consumption : 12W, CCT : 1800K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver or AC 110-230V, 50Hz, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition.LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, IP68, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP68 connector having the length >300mm. (Including TNP & Good for use.) The allowed tolerance shall be ±5%. Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.

SITC of high quality long through mono color Slim Linear wash light, Protection Rating : IP68, complying to BIS standard "IS 10322 (Part 5/Sec 1): 2012" /"IS 10322 (Part 5/Sec 5): 2013" and having CE certificate/Test certificates from National Accreditation Board for Testing and Calibration Laboratories/Government Labs against standard "Low Voltage Directive & Protective Equipment - EN 60598-1:2015", and "Electromagnetic Compatibility Directive - EN 61547: 2009", Mounting Structure : Adjustable surface mount yoke arrangements for fixing the lights. Power consumption : 15W, CCT : 1800K, (as per the design approval), Optics : PMMA with holder, Beam Angle : 15º/25º/45º/60º, Control : ON/OFF, Body : Die casted / extruded aluminium with embossed manufacturer logo, Hot spot and light distribution : Optics Designed to minimize hot spots & fringing in different applications. Power Input : Constant DC 24V with external driver or AC 110-230V, 50Hz, Surge Protection : Inbuilt surge protection in the driver 2KV-4KV(Additional if required will be added as per the requirement), Toughened transparent glass having the IK protection up to IK08, Painting : Chemical 3/7 tank processed treatment before the powder coat black/ash/approved color coat. Fixture will be suitable to operate in a temperature range of 0°C to 50°C, The light fixtures are having IP68 air vent made of stainless steel which helps to desiccate & prevent from forming moisture inside the light fixture at worst environmental condition. LED life should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. PCB thickness must be 1.6mm, 35 micron Copper, 2W TC with Black or White masking, Copper /OSP finish. LM79, IK08, IP68, HV Certificates from NABL Acrediated laboratory. LED Makes should be CREE, LumilLED, Osram, Seoul, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. Power Loop In/Out along with IP68 connector having the length >300mm. The allowed tolerance shall be ±5%. Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.

SITC of high quality Mono Color Neon Flexible light, Protection Rating : IP68, Mounting Structure : Adjustable wall mount SS clips for fixing the lights. Power consumption : 10W, CCT : 3000k, (as per the design approval) Beam Angle : 120º, Power Input : DC 24V with external driver or AC 110-230V, 50Hz, Surge Protection : Inbuilt surge protection 2KV-4KV(Additional if required will be added as per the requirement), Fixture will be suitable to operate in a temperature range of 0°C to 50°C , LED life time should be at least 50,000 burning hours at L70 at 35 degree centigrade. Luminaire is inclusive of Integral male/female waterproof connectors with structures in pre wired conditions as per IS standard. LED Makes should be CREE, LumilLED, Osram, Seoul, Epistar, Nichia or equivalent with the engineer or 3rd party testing laboratory approval. The allowed tolerance shall be ±5%. Make (Fittings):- Philips/Havells/Bajaj/K-lite/Leksa/Wipro or equivalent as per direction of E/I.