8210 REPAIR TO DRAIN, FENCING, BOUNDARY WALL, HARD STANDING, PATH GATE AND MISC B/R WORKS AT MIL STN SHAHJAHANPUR UNDER GE (E) BAREILLY.

Amount

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

M&L 40mm thick PCC 1:2:4 type B1 using 20mm graded stone aggregate laid in panel finished even and smooth with using extra cement as in flooring complete all as specified and directed.

Supply only glass dividing strip 3mm thick and 38mm wide in flooring complete all as specified and direcetd.

M&L 75 mm thick, PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection/foot path finishing cement concrete even and smooth with out using extra cement complete all as specified and as directed.

M&L for 100mm thick cement concrete type B-1 1:2:4 (using 20 mm graded stone aggregate) laid in panels as in hardstanding etc and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

M&L forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, grade 'A', 100 mm thickness of concrete slab complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in surface channels and base of drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and directed.

M&L for cement concrete 1:5:10, type E-2 (using 40 mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified and directed.

M&L for preparation of sunken floor and applying a coat of hot bituminous primer @ 0.30 kg/sqm and applying a coat of industrial bitumen 85/25 @ 1.20 kg/sqm over primer and laying modified polymeric water proofing membrane(weight not less than 3 kg/sqm 2 mm thick consisting 100 mm micron HMHDE FILM) and applying one coat of industrial btumen grade 85/25 @ 1.2 kg/sqm on top of membrane with 100 mm overlap at side end lap where required over 10 mm thick rendering in CM 1:4 including integral waterproofing compound 3% and taking down existing plastering as per manufacturer instruction and complete all as specified and directed

Removing existing water proofing treatment and preparing surfaces to the entire satisfaction of Engineer-in-Charge / GE including taking down existing plaster, cleaning of all foreign material such as grass, roots, dust etc and roughening the concrete surfaces by wire brushing and washing down to remove dust etc. flushing at junction of parapets complete and removing the same to the places where directed by Engineer-in-Charge

M&L for rendering 15mm thick on roof surfaces in CM 1:4 complete all as specified and direcetd.

M&L for preparation of roof surfaces, applying a coat of primer@ 0.40 Kgs/sqm applying a coat of bitumen grade 85/25 @1.2kg/sqm supplying and laying water proofing treatment with using polymeric water proofing membrane (weight not less then 3kg/Sqm) consisting of 100 micron HMHDPE film centre core including applying a coat of bitumen 85/25 grade @ 1.2kg per sqm on top surface of membrane and torch application of membrane with 10cm overlap where required and finally finished with and including a coat of aluminium paint @0.20 Ltr/Sqm as per manufacture instruction complete all as specified and directed.

Demolition of brick work in cement mortar incl all quoins, arches, pillars etc, but excluding ashler facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L brick work with sub class B bricks burnt straight or curved on plan exc 6 M mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class ‘B’ old size bricks straight or curved on plan to any radius as in half brick thick wall built in CM 1:4 complete all as specified and directed

Taking down cement plaster including racking out joints hacking for key and scrubbing down with water etc. complete all as specified and directed.

M&L rendering 15mm thick in cement plaster 1:4 on surfaces fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 15mm thick in cement plaster 1:6 on surfaces other than fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and directed.

M&L rendering 10mm thick in cement plaster 1:4 on concrete surfaces of ceilling and finished the surface even and smooth without using extra cement all as specified

M&L for two coats of cement base paint incl preparation of new surface of wall complete all as specified and as directed.

M&L for two coats of cement base paint incl preparation of old decorated surface of wall complete all as specified and as directed.

M& L for two coat of oil bound distemper incl preparation of new surface of wall complete all as specified and as directed.

M& L for two coat of oil bound distemper incl preparation of old treated surface of wall complete all as specified and as directed.

M&L for 1mm thick Wall putty (JK/Birla) on wall all as specified and directed

M&L three coat of white wash on wall including preparation of new plastered surface complete all as specified and directed.

M&L three coat of white wash on ceilling including preparation of new plastered surface complete all as specified and directed.

M&L preparing Old plastered or unplastered surfaces of wall and applying one coat of white wash on old decorated surface of wall complete all as specfied and direcetd.

M&L preparing Old plastered or unplastered surfaces of ceiling and applying one coat of white wash on old decorated surface of ceiling complete all as specfied and direcetd.

Dismantling floor hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for machine pressed pre-cast concrete interlocking coloured paver block and shape and size conforming to IS-15658-2006 of 60mm thickness M-35 grade with grey cement and pigment laid dry over and including 50 mm thick stone dust or sand base and compacted using vibrator complete all as specified and directed.

Demolition of stone slab and tiles of any description or thickness in floor, aprons etc. complete all as specified and directed.

M&L for machine cut mirror polished kota stone slab flooring 20-25mm thich over 15mm thick screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shad of the slab including round nosing at corners rubbing and polishing complete all as specified and directed.

M&L for machine cut kota stone slab as in flooring 20 to25 mm thick in floor riser of steps, skirting, dado,and pillars including rendering 15mm thick or bedding layer for laying floor finishes CM 1:4 etc set and jointed in neat cement slurry and jointed with greay cement slurry mixed pigment to match shade of slab incl rubbing and polishing complete all as specified and directed.

M&L for granite (of any type) tiles 20 mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing types over 20mm thick screed bed in CM 1:4 complete all as specified and directed.

M&L for 20 mm thick granite (of any type) tiles machine cut in skirting / dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete over 15mm thick rendering in CM 1:4.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed.

S&F solid PVC door frames of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (Style) consisiting of frame made out of MS tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain coloured PVC 'C' channel having a PVC sheet strip of 20 mm which stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rails & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement suppling & fixing in the frame at site as per specification & drawing.

S&F 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed as specified and as directed.

S&F 100 mm long butt hinges, extruded alminium alloy with galavanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed.

S&F 150 mm aluminium handles cast type, anodised complete all as specified and as directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) exc 1.5 sqm but n. exc 4 sqmeach complete all as specified and directed.

Taking down shutter of any description exc 1 sqm but n exc 2 sqm each

S&F alluminium alloy anodised door frame fixed with side hung shutters and glazing fixed with and including 4.80 mm thick tinted glass fixed with rubber gasket with aluminium heading, clips frame made with aluminium box sec as appended below complete all as specified and directed :- (a) Frame 80x44x1.98mm thick with rawl plug (b) Middle and lock rail : 150x44x1.98mm thick (c) Bottom rail : 150x44x1.98mm thick (d) Top rail/sype : 85x44x1.98mm thick (e) Aluminium beading : 0.7mm thick (f) Aluminium handle D type 150mm long, 100 mm long steel butt hinge, aluminium tower bolt 9.9mm dia shoot 200mm long brass mortice lock 100mm 4 leaver ,aluminium stopper, hydraulically regulated door closer ( Make Sandhu ISI marked or ites equivalent approved make) (g) Making good of wall surface to match with existing surface complete.

S&F aluminium anodised sliding windows ,shutter glazing with and including 4.8 mm thick tinted glass fixed with rubber gasket with aluminium beading, clips , frame, with duco pattern grill of size 75 mm X 75 mm and steel mosquito wire netting fixed with beading made with aluminium section suitable for three track slids . Making good of wall surfaces to match with existing surfaces complete all as specified and directed.

S&F aluminium anodised windows,ventiletators frame with side hung shutters and glazing with and including 3.8 mm thick tinted glass fixed with rubber gasket with aluminium beading ,clips, frame made with aluminium section as appended below (i) Frame :65X40X1.98 mm thick (ii) Top/bottom rail and style /rail of shutter : 44X47X1.98 mm thick (iii) Aluminium beading - 0.7 mm thick (iv) Aluminium fitting such as peg stay,aluminium hinges,aluminium handle 100 mm long,aluminium tower bolt 100mm long (v) Making good of wall surfaces to match with existing surfaces complete all as specified and directed

S & F Mild steel work as in chowkats/frame of door or gates of angle or other section with gusset plate, rail braces etc complete drilled for fixing of steel sheeting or other covering, doors etc to be prepared for hanging or sliding with and inclu either hooks and hinges or steel hanging door fittings (exclusive of steel, sheeting or other covering, running rails and guisides) and hanging also fastening and fixing complete all as specified and directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F 300 mm long mild steel sliding door bolts, ISI marked clip & bolt type, stove enamelled black, with bright bolt not less than 16mm dia with and including minimum 6 bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

S&F 2nd class hard wood glazed and skeleton shutters 35mm thick open rebated and prepared to receive glass, gauze etc (without sash bars) , edges of framing plain, chamfered or rounded , fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) , supplied and fitted to chowkats complete all as specified and directed.

S&F 100 mm butt hinges medium weight cold rolled mild steel and fixed

S&F 150 mm long mild steel pressed handles oval type stove enamlled black complete all as specified and directed.

S&F 200 mm long mild Barrel tower bolt, oval type stove enamlled black with bright bolt and fixed

M & L preparing wood or wood based surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Taking down steel/wooden window of any size and description complete.

S&F steel windows with side hung shutters including projecting type hinges with steel handles, and steel peg stay complete without glazing bars, dovetailed or welded.

S&F steel windows with side hung shutters including projecting type hinges with steel handles, and steel peg stay complete with glazing bars, dovetailed or welded.

S&F steel ventilator with top hang shutter including hinges steel pag stay,complete.

M&L framed work such as grills grating etc with end of bars shoulderd and/or riveted welded or forged into spikes framedguard bars iron doors ladders framed balusters, walk ways. Railings, frame work of of water tanks and ssimilar work conforming to Fe410 complete all as specified and directed.

S&F 3 mm thick sheet glass, Ordinary quality and glazing with oil putty in square n. exc 0.5 Sqm in each pane complete all as specified and as directed.

All as per Srl item No. 70 here in before but 4.8mm thick frosted sheet glass.

S& F galvanised mild steel wire clothes 0.56 mm nominal dia of wire and average width of aperture1.18 mm complete all as specified and as directed .

S&F 0.80 mm thick mild steel plain black sheet in hearths, covering to door chowkhats (frames) chullah hoods, water tanks , water troughs, ducts, urinal trough and funnels etc, cut to size, edge beaded if directed, holes punched, including round headed screws, clout nails or rivets and fixed to wood or steel members, etc with plain 40 mm lap joints or welded /riveted seams including bending, turning up,mitred angles, stopped ends, outlets etc as required complete all as specified and directed.

M&L applying 2 coats of synthetic enamel paints on new steel surfaces over a coat of red oxide primer including surface preparation over 10 cm width and girth complete all as specified and directed.

Hacking out old broken glass of (any thickness, size, quality or description) from old wooden/steel frame, or stones, concrete or brick surrounds glazed with putty or fixed with beads complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20mm graded stone aggregate) for filling in bed block of hold fast etc complete all as specified and direcetd.

S&F in repair vitreous china wash down water closet pan (pedestal pattern) white(excluding flushing cistern and flush pipe) including connection to drain or out going pipe and flush pipe anti symphonize pipe etc complete all as specified and as directed.

Supply only plastic water closet seat cover black closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device

S&F in repair for CP Health Faucet with 1 Meter Flexible tube & Hook complete all as specified and directed.

S&F in repairs 15mm dia two way angle valve, cast copper alloy, chromium plated screwed down, high pressure with crutch or butterfly handle complete all as specified and directed.

S&F in repair Jet spray chromium plated with 1mtr heavy PVC hose butterfly type, with chromium plated nuts complete all as specified and directed.

Disconnecting existing PVC water tanks of 500 ltrs capacity, setting aside (or lowering if required) for repairs, cleaning with bleaching powder, etc and hoisting if required reconnecting and refixing in same position as specified and as directed.

Disconnecting existing PVC water tanks of 1000 ltrs capacity, setting aside (or lowering if required) for repairs, cleaning with bleaching powder, etc and hoisting if required reconnecting and refixing in same position as specified and as directed.

S&F GI tube 15 mm dia medium grade with all fittings and fixed to wall, ceiling or laid in floors including taking down existing GI tubing 15 mm dia & connections complete all as specified and directed.

Taking up or down existing GI Tubing 15 mm dia & connections including cleaning for refixing seviceable the same with new fittings and fixed to wall, ceiling or laid in floor and ceiling and wall all as specified and dircted

S&F GI tube 20 mm dia medium grade with all fittings and fixed to wall, ceiling or laid in floors including taking down existing GI tubing 20 mm dia & connections complete all as specified and directed.

Taking up or down existing GI Tubing 20 mm dia & connections including cleaning for refixing seviceable the same with new fittings and fixed to wall, ceiling or laid in floor and ceiling and wall all as specified and dircted

S&F rotational moulded polethylene water tank of 500 ltrs capacity, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 500 ltr complete all as specified and directed.

S&F rotational moulded polethylene water tank of 1000 ltrs capacity, ISI Marked (cylindrical vertical with closed top) hoisted and fixed in position all as pacific SSR Part- I including dismantling of existing water tanks capacity n exc 1000 ltr complete all as specified and directed.

S&F 20mm ball valve high pressure of PTMT with epoxy coated aluminium rod and high denty plastic ball screwed for iron pipe and fixed (min wt. 210gms) complete all as specified and directed.

S&F 20 mm dia gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section including taking out embedded portion and making good disturbed ground post embedded in concrete, brick work, masonry etc complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n exc 50m and making good sufrace in soft/loose soil complete all as specified and directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in foundation/mass concrete complete all as specified.

S&F MS angle post & struts as arms over compound wall in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

S&F mild steel screw bolts (machine made) with hexagonal or square head at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 30 cm long and dia meter of neck in mm n exc. 12mm.

Supply and Fixing in repair chain link fencing including line wires, any mesh size and type of any type of standards, rails, straining bolts etc including provision of binding wire. Wt 3 to 4 Kg per Sqm complete all as specified and directed.

M&L for 10mm dia and over mild steel TMT bars, cut to length , bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips, quality of steel conforming to demormed or twisted bars Fe-410-W (Gde E-250) complete all as specified and directed.

S&F in repairs Galvanised 2 strand , steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rail straining bolts including securing or tying at crossings with and provisons of galvanised mild steel wire, staples or steel pins etc as directed (each line wire to be measured) complete all as specified and directed.

Dismantling structural steel work wrought iron or mild steel work including door, gates, of any description not otherwise provided for complete all as specified and directed.

S&F of Rolled sections of Fe-410-W (Gde-E-250) quality-B as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including bending, welding etcincl one shop coat of zinc chromate primer incl preparation of surfaces complete all as specified and directed.

S&F in repair for Amstrong ceiling made out of 600x600x15 mm thick classic lite(RH-95) mineral fibre acoustics ceiling board/tiles with and including powder coated exposed GI grid suspension system (E-Grid T-2430 or equvalent load carrying capacity with mid span deflection not exc. 1/360 span with hanger spacing of 1200mm c/c) consisting of main runner 3600mm long, cross Tee 1200mm/600mm long and wall angle. The main runners to be placed @ 1200mm, the cross Tee 1200mm will be inserted in the pre cut slots of main runner at a regular interval of 600mm to form a modular grid of 1200mmX600mm. Additional cross Tees of 600mm shall be placed perpendicular to the cross tee 1200mm long to finally form a grid of 600mmX600mm. Grid of modular size 600mmX600mm shall be supported by 6 mm dia G.I. wire for suspending, bolts, necessary washer, nut/ clits/ pin hook etc for securing frame work to ceiling to the snap gridcomplete all as per manufacturer's instruction.

S&F in repairs insulated PVC wall lining 25mm thick consisting of PVC insulated panels having expanded polystyrene (EPS) stuck to 2mm thick plain colour PVC sheet duly fitted into the wall as per specification and drawing.

S&F in repair chromium plated curtain rods including CP knobs and brackets complete all as specified and directed.

S&F in repair 600mmx450mm bevelled edges mirror consisting of 5.5mm thick commercial plywood and fixed to plug with chromium plated brass screwed and cup washer complete all as specified and directed.

S&F in repair Aluminium Mortiee lock 4 lever, size 75mm complete all as specified and directed.

S&F in repair door closer aluminium (Die cast) body hydraulically regulated, designation No 3, universal type, suitable foor door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.complete all as specified and directed.

S&F in repair double action floor spring hydraulically regualted made up of minimmum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless stell cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all as specified and directed

Dismantling Asbestos Cement/CGI (Corrugated, Semi corrugated etc.) sheets in roof coverings complete all as specified and directed.

M&L 6mm thick Asbestos Cement, one piece plain angular ridge in roof fixed with L Type or J type or crancked hook bolt etc.complete all as specified and directed.

M&L 6mm thick Asbestos Cement, Corrugated or Semi corrugated sheets in roof, wall fixed with L Type or J type or crancked hook bolt etc.complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 55- Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F pre-painted galvalume aluminium zinc coated GI based plaint steel sheet 0.50 mm thick of an colour having tensile strength of 55- Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F in repair PVC waste pipe of 32/40mm dia complete all as specified and directed.

S&F in repair kitchen sink coupling of any size and any pattern including waste pipe complete all as specified and directed.

S&F in repair bib taps 15mm bore standard of PTMT any colour high pressure screwed for iron pipe and fixed all as specified (minimum wt. 90gms) complete all as specified and directed.

S&F (in repairs) Bib taps cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed for iron pipe or or brass ferrule for 15 mm bore of pipe complete all as specified and as directed.

S&F (in repairs) angle cock cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule for 15 mm bpre of pipe complete all as specified and as directed.

S&F (in repairs) Stop cock (Concealed) cast copper alloy chromium plated fancy type with crutch or butterfly handle screw down ,screwed both end for iron pipe or or brass ferrule with long shank and cup for 15 mm bpre of pipe complete all as specified and as directed.

S&F in repair swivel shower rose of brass Chromium plated for fixing with 15mm pipe fixed complete all as specified and directed.

S&F in repair vitreous china squatting pan "Orissa" pattern size 580mmx440mm white with integral foot rests excluding flushing cictern and flush pipe all as specified and directed

S & F in Repair 10 ltrs capasity PVC valveless syphonic action type flushing cistern low level white, with inlet ball valve, float and handle including bracket and flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern complete all as specified and as directed.

S&F in repair vitreous china wash basin white, flat, back, size 550x400 mm excluding tap waste but including brackets and including cutting for and pinioning in ends of brackets but exclusive of supply waste pipe all as specified

S&F in repairs 15mm bore pillar tap cast copper allloy with capstan head Chromium plated scwed down with or without letter Hot or Cold with long shank and fly nuts scrwed for iron pipe and fixed as specified and directed.

S&F PVC connection 15mm bore length not less than 300 mm long with both ends PTMT nuts complete all as specified.

S&F in repair 15mm bore angle stop valve of PTMT any colour high prssure screwed for iron pipe and fixed all as specified (minimum wt. 90gms) complete all as specified and directed.

S&F in repair CP towel rail 20mm dia, 600 mm long between flanges complete all as specified and directed.

S&F in repairs brass CP basin mixer for mixing hot & cold water screwed down for iron pipe and fixed of 15mm dia pipe complete all as specified and directed.

S&F in repairs brass chromium plated wall mixer any type and shape with all fittings complete all as specified and directed.

S&F in repairs 75 mm dia PVC (SWR) floor trap plain with greting incl jointing with solvent cement complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) pipes of single socketed in any length with rubber ring joints fixed to wall all as specified and directed.

S&F 75 mm bore PVC (SWR) bends complete all as specified and directed.

S&F 110mm bore PVC(SWR) junction single (single T) equal or unequal with access door complete all as specified and directed.

S&F 110 mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm PVC (SWR) bend any radius complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches complete all as specified and directed.

Taking down aluminium door shutter and replacement of parts such as rubber beading, glass panes, mortice lock, floor spring, hydraulic door closer and other fittings and refixing in the same opening after replacement of parts complete all as specified and directed.

M/S SHAHABUDDIN AND SONS

m/s udit constructions

M/S DEEN ENTERPRISES

M/S MANSI TRADERS