Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
Refer Docs
Closing Date
30 May 2024, 5:30 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Mission & Combat System R & D Centre
HINDUSTAN AERONAUTICS LIMITED Mission & Combat System R & D Centre
VIDEO SOURCE AND VIDEO MONITORS FOR VIDEO CONVERTER UNIT
6838
GEM/2024/B/4894821dated 27/04/2024
IMM
Unknown (Unspecified Location)
30 May 2024
27 May 2024
27 May 2024
18 May 2024
Mission & Combat System Research & Design Centre HINDUSTAN AERONAUTICS LIMITED Marathahalli Post Bangalore - 560 037 INDIA
Technical Terms and Conditions of Tender - Annexure - 1
Name of the Vendor
Name of Work: Video Source and Video Monitors (VSVMs) For Video Converter Unit
PLEASE INDICATE YOUR RESPONSE/ COMPLAINCE/ACCEPTANCE TO THE FOLLOWING TERMS (MANDATORY). INDICATE THE TECHNICAL SPECIFICATION/RANGE AGAINST HAL TECHNICAL REUIREMENTS WHEREVER NECESSARY
Scope of Work Vendor's Compliance (Complied or not complied)
1 Purpose The purpose of this document is to describe the technical requirements for Video source, Video Monitors and power supply for testing the Video Converter Unit (VCU).
2 SCOPE The scope of this document defines the requirements of the video source for VCU and Video display monitors (VSVMs) for monitoring the input and output videos of VCU along with the 28VDC power supply.
Vendor has to provide the following test equipments for functionality testing of VCU:
S.N Line Item Description/P/N Qty Note
1 RS170 PAL Analog Video Source along with built-in Video Splitter 2 Nos Dedicated power cards or Power adapters to each line item to be provided.
2 14” RGsB Video Display Monitor 1No
3 14” RS170 Video Display Monitor 1No
4 28VDC Bench Top Programmable Power supply, 2U Size, 24A/800 Watts or equivalent 1No
5 VCU Testing Looms - 7 meters of each loom as per the aircraft standard 2 set EMI Shielding and Labelling on each wire is required
3 TECHNICAL FEATURES OF VIDEO CONVERTER UNIT (VCU) 3.1 VCU OVERVIEW VCU is an airborne video converter unit, responsible for accepting PAL standard RS170 video from Avionics system as an input and provides STANAG3350B standard RGsB (with Sync on Green) analog video as an output for recording purpose. The interface diagram of VCU is given in the following figure1:
4 VCU EXTERNAL INTERFACES
S/N Interface Name Interface Type Used Remark(s)
1 Video Input 1 RS 170-PAL video
2 Video Output 1 STANAG3350B RGsB video
3 28VDC Power Power supply 1 Powering up VCU
Table 1: External Interfaces of VCU
5 VIDEO INPUT & OUTPUT CHARACTERISTICS OF VCU A brief characteristic of the external video interfaces of VCU are given below:
5.1.1 VIDEO INPUT
S/N Type Video Standard No. of channels Characteristic(s)
1 Analog Video RS170 - PAL Video Type: Unbalanced Signal levels: 1V (pk-pk) in terminated condition (625 Lines / 50 Hz Field) 1 Analog Video Signal Zin = 75Ω, 25 FPS , Coaxial 75 ohm RG179 cable, chromatic Video, Signal Levels: 0-1V(Pk-Pk) in terminated condition
Table 2: Video Input Characteristics
5.1.2 VIDEO OUTPUT
S/N Type Video Standard No. of channels Characteristic(s)
1 Analog Video RGsB STANAG 3350B Video Type: balanced differential (625 Lines / 50 Hz Field) 1 Analog Video Signal , Zout = 120Ω, Differential Balanced Video , Shielded Twisted Pair Signal Levels: 0.5 to 2.5 Vp-p@ 120Ω
Note1: The cables, mating connectors and loom preparations are under the scope of the vendor. The EICD (ELECTRICAL INTERFACE CONTROL DOC) for J1 & J2 loom of VCU will be provided by HAL after P.O Placement. Note2: CH1 & CH2 video output terminals from RS170 Video GEN are identical and both should be available simultaneously from the video GEN. III. VCU shall be connected with the 7meter length of J1-power loom, and 7 meter length of J2 loom for video input & output. Each cable loom should have proper shielding and grounding. IV. VCU has two fixed connectors which are (i) J1 Power Connector - D38999/20WC35PN and (ii) J2 Video Connector - D38999/20WD35PN.
6.2 VCU Video Test Equipments Following instruments/equipments are required for VCU Functional Testing. a. RS 170 PAL Video Generator with (1-2 Channel)Video Splitter b. RS170 Analog PAL video monitor c. RGsB analog video Monitor d. Bench Top 28VDC Programmable Power Supply (Ref: TDK Lambda) or equivalent e. VCU Testing Looms The block diagram of VCU Test Setup is shown in Figure-2.
6.2.1 Video Source with video splitter i. RS170 PAL Video shall be generated as per sec 5.1.1 ii. Generated RS170 PAL video output shall be splitted into two channels using 1-2 Channel Video Splitter. iii. RS170-PAL Video generator shall have the provision for fine turning of the video output levels with respect to timing and signal amplitude if required. Adjustment of Video output shall be demonstrated with procedure manual. iv. Video source shall be able to generate the various pattern of RS170 PAL Video and video patterns shall be selected for output through manual option or remote option. v. The same selected video pattern output should be available simultaneously on the both channels of CH1&CH2. vi. Minimum 720 x 576 resolution standard video pattern as a minimum requirement vii. Video source shall be able to drive RS170 PAL Video output on 7meter cable.
6.2.1.1 Video Source Specifications
Sl. No Specifications Description
1 Analogue Video Output Default Video output details are following: RS170 – PAL Video Video Type: Unbalanced 75 Ω Signal levels: 1V (pk-pk)- Terminated (625 Lines / 50 Hz Field)
2 Video Output Adjustments Provision for luma gain adjustment Provision for chroma gain adjustment Provision for Contrast adjustment Provision for Brightness adjustment
3 Operating temperature -5°C to +55°C
4 Storage temperature -20°C to +80°C
5 Power 230V AC ±10%
6 Relative humidity 0 to 95% RH
7 Accessories Power Cord with suitable Adaptor as per IS-1293
Note: RS170-PAL Video waveform technical details will be discussed with the Vendor after PO Placement for fine turning of video output if required.
6.2.2 RGsB Video Monitor for analog Video output Display i. Accepts the STANAG 3350B, RGsB video (576i /50 Hz) with 120Ohm Differential ii. Video Monitor is table-mount with stand iii. Operated with 230V AC input. iv. Resolution shall be selectable and adjustable v. Minimum resolution shall be as per input format video vi. LCD panel for wider viewing angle and excellent color purity. vii. The electrical loom shall be prepared as per the EICD with unit mating J2 connector provided by MCSRDC HAL. The Video cable of 7meter loom shall be interface the Video source, Video monitor and VCU.
6.2.2.1 RGsB Video Monitor Specifications
Sl. No Specification Description
1 Video Input RS 170 analog 75 Ohm
2 Levels ±1.0Vpp ±10% at 75Ω
3 Max levels 1V (pk-pk)- Terminated
4 Input Selection By MENU Selection
5 Output Screen Type 14” LCD Monitor Display
6 Display-Resolution 720X576
7 Aspect Ratio 4:3, Refresh Rate: 50Hz
8 Brightness 300 cd/m2 (with the adjustment provision)
9 Installation/Mounting Table Mountable / with Stand
10 Operating temperature -10°C to +60°C
11 Storage temperature -20°C to +80°C
12 Power 230V AC ±10%
13 Relative humidity 0 to 95% RH
14 Accessories Power Cord with suitable adaptor (if applicable) as per IS-1293
Sl. No Specification Description
1 Video Input RS 170 analog 75 Ohm
2 Levels ±1.0Vpp ±10% at 75Ω
3 Max levels 1V (pk-pk)- Terminated
4 Input Selection By MENU Selection
5 Output Screen Type 14” LCD Monitor Display
6 Display-Resolution 720X576
7 Aspect Ratio 4:3, Refresh Rate: 50Hz
8 Brightness 300 cd/m2 (with the adjustment provision)
9 Installation/Mounting Table Mountable / with Stand
10 Operating temperature -10°C to +60°C
11 Storage temperature -20°C to +80°C
12 Power 230V AC ±10%
13 Relative humidity
14 Accessories Power Cord with suitable adaptor (if applicable) as per IS-1293
6.2.4 Bench Top 28VDC Programmable Power supply i. The Power Supply Unit shall generate the 28VDC from 230V±10%, 50Hz±10%. ii. DC Regulated programmable power supply shall be in 2U Size and output terminal shall be insulated port. iii. The output voltage shall be variable from 0V to 36V with a 0.1V resolution iv. Provided Max load current up to 24A & output power of 800W. v. Output Regulation (DC): 0.5% max change in output voltage per 10% change in input; Ripple figure for DC Output voltage shall not exceed 10mV rms. vi. The power supply shall have protective function such as OVP, UVP, Thermal and Fold-back protection and over current protection by setting the current limit. vii. The electrical loom shall be prepared as per the EICD with unit mating J1 Power connector as per EICD provided by MCSRDC HAL for powering up the VCU. viii. Power Cord with suitable adaptor (if applicable) as per IS-1293 ix. The Programmable Power supply Model & Manufacturer is given below for reference: Model: TDK-Lambda Z+ 36-24 (Z+ 800 Series or above) or equivalent.
6.2.5 VCU TESTING Looms VCU Testing Loom shall consist of the following dedicated sub looms for video testing: A. J1-POWER LOOM - (P1 To VCU-J1) B. J2-VIDEO LOOM - (J2-Vin LOOM & J2-Vout LOOM ) C. Vin TEST LOOM - CH2 To VM2 6.2.5.1 J1-POWER LOOM (P1 To VCU-J1) I. This loom is connected between the VCU J1 Connector and P1 terminals of the Bench top 28VDC Power supply. II. One end of the J1-POWER LOOM should be D38999-26WC35SN and another end of the loom’s connector should be mate with the Bench top power supply Terminals P1. III. The wiring will be done as per the Electrical ICD provide by MCSRDC, HAL. IV. The J1-POWER LOOM details given below: a. The J1 mating connector is Mil standard D38999-26WC35SN b. Loom length is minimum length of 7 meter. c. EMI shielding of the cable is mandatory. d. The power cable of single core, shielded @ 5A rating shall be used e. The power Loom cable P/N: 806-1-0.38 from M/s.Filotex or M27500/22WJ1S06 from M/s Sanghwi or equivalent shall be used.
6.2.5.2 J2-VIDEO LOOM (J2-Vin LOOM & J2-Vout LOOM ) I. This J2-VIDEO LOOM consists of the J2-Vin Loom and J2-Vout Loom. II. This loom should have back shells of P/N: D-Size Non- Environmental EMI/RFI Straight Back shell with Spin Coupling P/N: M85049/1915W05.
6.2.5.2.1 J2-Vin LOOM: I. J2-Vin loom shall be used to provide the input video signals from the RS170 Video source (CH1) to the VCU-J2 connector. II. One end of this J2-VIN loom shall be made with J2 mating Connector D38999-26WD35PN. III. Another end of this loom shall be made using the suitable mating connector for (CH1) RS170-PALVideo source. IV. The wiring shall be done as per the Electrical ICD provide by MCSRDC, HAL. V. The J2-Vin LOOM details given below a. The J2 mating Connector is Mil standard D38999-26WD35SN b. Loom length is minimum length of 7 meter c. EMI shielding of the cable is mandatory d. Triaxial cable of 75 Ohms impedance, P/N: ETUDE 49893 (FILOTEX) or equivalent shall be used.
6.2.5.2.2 J2-Vout LOOM: I. J2-Vout loom shall be used to get the video output signals from the VCU-J2 connector and provides to the RGsB video monitor terminals VM1 (R, Gs & B). II. One end of this J2-Vout loom shall be made with J2 mating Connector D38999-26WD35PN. III. Another end of this loom shall be made using the suitable mating connector for RGsB Video monitor (VM1) terminal. IV. The wiring shall be done as per the EICD provide by MCSRDC, HAL. V. The J2-Vout LOOM details given below a. The J2 mating Connector is Mil standard D38999-26WD35SN b. Loom length is minimum length of 7 meter c. EMI shielding of the cable is mandatory d. The twisted pair cable of 120 Ohms impedance, P/N: 2524H0524 M/s Raychem or equivalent shall be used.
6.2.5.3 Vin TEST LOOM – (CH2 To VM2) I. Vin Test loom shall be used to connect the RS170-PAL video second channel (CH2) output to the RS170-PAL video Monitor terminal (VM2). II. Loom length is minimum length of 7 meter III. EMI shielding of the cable is mandatory IV. Triaxial cable of 75 Ohms impedance, P/N: ETUDE 49893 (FILOTEX) or equivalent shall be used along with suitable mating connectors on both ends.
6.3 VSVM Deliverables Module tester meeting all the Technical requirements given in section 6.1 shall be delivered to HAL. The list of deliverable items is given below in table 4.
S.N Item Quantity
1 Analog Video Source as mentioned in Section 6.2.1 along with built-in video splitter (i) Power Cord with Power adapter suitable to IS-1293 (ii) Driver Software CDs (if applicable) (iii) COCs, User manual/Operating Manual 02 Nos
2 14” RGsB Analog Video display Monitor mentioned in section 6.2.2 & 6.2.2.1 along with (i) Power Cord with Power adapter suitable to IS-1293 (ii) Driver Software CDs (if applicable) (iii) COCs, User manual/Operating Manual 01 No
3 14” RGsB Analog Video display Monitor mentioned in section 6.2.2 & 6.2.2.1 along with (i) Power Cord with Power adapter suitable to IS-1293 (ii) Driver Software CDs (if applicable) (iii) COCs, User manual/Operating Manual 01 No
Table 4: Deliverable Items List
6.4 Delivery schedule
S. No. Deliverables Qty Delivery Schedule (in weeks)
1 RS170 PAL Analog Video Source with Splitter and Power adaptor & power cable 2No T0+10 Weeks
2 14” RGsB Video Display Monitor with Power adaptor and power cable 1No
3 14” RS170 Video Display Monitor with Power adaptor and power cable 1No
4 28VDC Bench Top Programmable Power supply, 24A/ 800W, with Power cord and suitable adaptor 1No
5 VCU Testing Looms - 7 meters of each loom as per aircraft standard 2 sets
T0: Date of providing the technical inputs to the Vendor by MCSRDC after the placement of PO.
Table 5: Delivery Schedule
7 General Requirements i. Vendor/OEM/Manufacturer should have supplied qualified airborne standard video test equipments in the last five years with same/similar specifications as given in this RFQ to reputed aerospace industries or defense organizations across the globe and for use on an airborne military platform. Copies of the Purchase orders and project completion details shall be provided as evidence to ascertain the credentials. ii. Vendor shall have Quality Management System - ISO 9001 and/or Aerospace AS9100 certification/approval and required to submit the copies of the same along with technical offer.
8 Acceptance i. Vendor shall demonstrate the functionality of supplied items as mentioned in sec 6.3 at MCSRDC, HAL. Each line item has to be tested as per the user manual or acceptance test procedure. Testing shall be carried out as per the ATP along with actual LRU (VCU) as per Fig2. ii. The ATP report will be generated along with QC MCSRDC for acceptance. iii. 20% changes in the electrical loom modification, adjusting the video source Amplitude/timing parameters, reports and documents proposed by HAL, MCSRDC shall be incorporated by vendor.
‹慗牲湡祴愠摮匠灵潰瑲椊卖䵖瘠湥潤桳污牰癯摩慷牲湡祴漠業楮畭湯敹牡映潲桴慤整漠捡散瑰湡散戠⁹䅈ⱌ䴠千䑒⹃椊嘠湥潤桳污湥畳敲琠慨⁴桴煥極浰湥獴眠汩敢猠灵潰瑲摥眠爮琮爠灥楡Ⱳ爠灥慬散敭瑮愠摮猠慰敲畳灰祬映牯愠洠湩浩浵瀠牥潩景㈠礠慥獲愠瑦牥眠牡慲瑮ᜊ᠀ഁࠀ敂据潔⁰㠲䑖⁃牐杯慲浭扡敬倠睯牥猠灵汰⁹敭瑮潩敮湩匠捥楴湯㘠㈮㐮愠潬杮眠瑩੨椨 潐敷潃摲眠瑩潐敷摡灡整畳瑩扡敬琠卉ㄭ㤲″†⠊楩 牄癩牥匠景睴牡䑃湡椨灡汰捩扡敬椨楩 佃獃獕牥洠湡慵⽬灏牥瑡湩慍畮污*O Pß̈嘀啃吠卅䥔䝎䰠潯獭洠湥楴湯摥椠敓瑣潩⸶⸲ਵ椨 ㅊ倭坏剅䰠住⁍ⴠ†獡瀠牥匠捥㘠㈮㔮ㄮ⠊楩 ㉊嘭䑉佅䰠住⁍ⴠ愠数敓⸶⸲⸵ਲ椨楩 楖䕔呓䰠住⁍獡瀠牥匠捥㘠㈮㔮㌮⠊癩 潃瑮湩極祴☠䴠来敧整瑳爠灥牯⁴湡佃⁃潦潬浯, -9㘀㈮㌮ㄮ††删ㅓ〷䄠慮潬䅐⁌楖敤潍楮潴灓捥晩捩瑡潩獮 ‰潴㤠┵删慈ࠂ‶䍖⁕䕔呓匠呅唠⁐㘊ㄮ䐠獥牣灩楴湯漠䍖⁕整瑳猠瑥灵䤊湉琠敨嘠啃琠獥⁴敳畴Ɒ删ㅓ〷倠䱁瘠摩潥漠瑵異⁴桳污敢猠汰瑩整湩潴琠潷挠慨湮汥ⱳ漠敮漠桴档湡敮獬猠慨汬戠楤敲瑣祬挠湯敮瑣摥琠卒㜱‰䅐⁌楖敤潭楮潴湡瑯敨档湡敮桳污敢映摥琠桴䍖⁕
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
raw.json
RAW_JSON
GeM-Bidding-6348984_1714211538.pdf
TENDER_DOCUMENT • 0.11 MB
boq_item_sample_file_1714211379.csv
TENDER_DOCUMENT • 0.00 MB
TB12136_1714211381.xls
BOQ_DOCUMENT • 0.14 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .