SPECIAL REPAIRS REPLACEMENT OF LT PANELS, PROVN OF ANTI SUCIDE FAN RODS (PH-II), PROVN OF ALLIED SERVICES FOR INSTALLATION OF DG SET PROVN OF WALL MOUNTED FANS AND PROVN OF FLAME PROOF LIGHTS AND EXHAUST FANS (05 JOBS) AT ATS BELAGAVI

Amount

S&F Anti suicide fan rod suitable for ceiling fan at depth ranging from as per site requirement of any sweep and any make , white in colour , MS pipe Zinc plated 12" MS Pipe Zinc Plated 19mm outer dia, 1.8mm + 0.05mm thick, spring set grade 3 Carbon steel material zinc plated, MSME tested for performance test and opening at impact load of 22 kg and spring ' hidden in pipe' should expand to about one metre or more including provn of buzzer for alrming,shackle clamp, nut & bolts, washers, split pin, rubber clamp etc. including taking down existing ceiling fan with down rod from its position and refixing the same in its original position with anti suicide fan rod complete all as specified and directed. Make:- Gold life of Safe Solutions Industries / Safe Halo or equivalent make as approved by GE Note : (i) Trial test for proper functioning of anti suicide rod shall be carried out infront of User Rep and Engr-in-Charge. (ii) Test results certificate shall be produced by the contractor. (iii) The unit rate quoted is deemed to be inclusive for the provn of 1.5 sqmm cable of suitable length as per site requirement.

All as per Srl item No.01 above but 24" -ditto-

Supplying, laying, connecting and testing of cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor, 1100 Volts grade, cross sectional area 50 Sqmm 3.5 core cable complete all as specified and directed

All as per Srl item No.3 above but 16 Sqmm 4 core -ditto-

All as per Srl item No.3 above but 35 Sqmm 3.5 core -ditto-

All as per Srl item No.3 above but 25 Sqmm 4 core -ditto-

Excavation in trenches, not exceeding 1.50m wide and not exeeding 1.50m in depth for foundations, trenches of cable or pipe lines etc or and getting out in hard/dense soil complete all as specified and as directed.

M&L for cutting the tar macadam road / hard standings for laying cable and excavating not exe. 60cm wide and n. exc 75cm depth and getting out all as directed including filing back, consolidating etc complete and finishing it with 200mm thick PCC 1:4:8 type D-2 (using 20mm graded crushed stone aggregates) complete all as specified and directed

S&F galvanised iron pipes 50mm bore light grade, with all fitting and fixed complete to poles/route/drains etc and ceillings or laid in floors complete all as specified and directed

All as per Srl item No.9 above but 40mmbore -ditto-

All as per Srl item No.9 above but 80mmbore -ditto-

S&F double wall corrugated (DWC) HDPE Pipe IS-16205, 75mm outer dia for cable protection in wall/under gorund laying of UG cables including SNAP-FIT Coupler and all fittings as required at site complete all as specified and as directed

All as per Srl item No.12 above but 40mm outer dia -ditto-

Returning filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soil complete all specified and as directed.

Removing excavated materials /soil to a distance not exceeding 50 meters and depositing where directed at a level not exceeding 1.5 meters above the starting point complete all specified and as directed.

M&L for LT Cable route indicator with a welded/riveted disc of 4 inch dia and engraved with cable with cable route marker made out of angle iron 40mm x 40mm x4 mm thick dug in ground with in and incl PCC 1:3:6 type C1 (using 20mm graded crushed stone aggregates) at approx distance 100 mtr including necessary earth work complete all as specified and directed

S&F vertical TPN DB incommer 4 way 12 outgoing having Powder coated sheet steel enclosure fitted with bus bar, DIN channel & neutral link & earth link complete all as specified and directed. Make:- Indo Asian Cat No 811888 or equivalent make as specified in list of manufacturers of Particular Specifications

S&F 4 Pole MCCB 63 Amp, 50 Hz, 415 V with rupturing capacity 16 KA complete all as specified and directed.

S&F 415V 10KA 'B' curve miniature circuit breaker (MCB) of TPN/FP and current carrying capacity 32 Amps in the DB complete all as specified and directed.

M&L for sub main wiring with 2runs of 10 Sqmm PVC insulated FR Copper conductor cable including PVC Conduit/Casing Capping of Suitable dia along with one run of 10 Sqmm FR copper cable for earth continuity conductor as earth lead for sub main wiring and connecting to common earth dolly complete all as specified and directed..

M&L for earthing complete with galvanized steel earth plate electrode 600mmX600mmX6 mm thick buried directly in ground (earth pit not le. than 2.25m deep below normal ground level) with top edge of the plate not le. than 1.5 m below normal ground level connected to GI Earth wire 4 mm dia by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.5 of .R part I including nece.ary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm long reinforcement, watering funnel, 40 mm dia light grade for protection of earth electrode 20 mm dia for watering all as specified and directed and tested on completion.

M&L for earthing and testing complete with galvanized iron earth plate electrode 600mmX600mmX 6mm thick buried directly in ground vertically to a depth not less than 2.25m below normal ground level with top edge of earth plate at a depth not less than 1.5 M below normal ground level connected to and including GI strip 32mmX6mm as earth lead by means of bolts and nuts, check nuts and washers etc made of GI & connected to equipment and earthing test point , earth dolly all as shown in elect plate No 3 of SSR Pt-I including all necessary earth work, excavation PCC chamber cover with handle (PCC 1:2:4) and 20mm dia GI watering pipe and 40 mm dia light grade GI for protection of earth strip, wire mesh, funnel, charcoal dust & common salt, etc all as specified and directed

M&L for point wiring for one light/exhaust fan point controlled by one switch with two runs of single core 1.5 Sq.mm (nominal area) PVC insulated unsheathed multistranded copper conductor cable confirming to IS drawn through and including in stove enamelled steel conduit concealed/semi concealed including Flush type metal GI boxes for fixing modular type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm. copper conductor as earth wire connected to common earth dolly and earth in distribution board including cutting of stone masonary/ wall Complete all as directed all as specified

S&F LED light fitting 1x16 Watt flame proof, CMRI certified recommended for gas/ vapor group of IIA & IIIB, Zone 1 & 2 and IP 65 protection with die cast aluminum hosing with heat resistant toughened glass with LED tube light fixtures driver, holders, connector etc. complete with all accessories prewired and including connecting up with three core flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F Aluminium flame Proof exhaust industrial fan,AC single Phase, 230V of 12'' size, 1440 RPM, including louvers, Gas Gr- I IIA & IIB Zone and connecting upto ceiling rose complete with all accessories complete all as specified and directed.

M&L for sub main wiring with 2runs of 1.5 Sqmm PVC insulated FR Copper conductor cable including PVC conduit/casing capping of suitable dia along with one run of 1.5 Sqmm FR copper cable for earth continuity conductor as earth lead for sub main wiring and connecting to common earth dolly complete all as specified and directed.

S&F wall mounted fan, AC single Phase. 230V of size 400mm sweep,60W input power,1350 RPM, 85CMM, air delivery and thermal overload protection for long lasting motor,air delivery complete all as specified and directed.

M&L for 5A/16A, 5 in 1 flush type switch socket combinastion with box and fuse & neon indicator complete all as specified and directed.

M&L for PVC insulated flat twin core sheathed cables standard aluminium conductor 1.1 KV grade of size 10 sqmm cable including taking down old cable complete all as specified and directed.

M&L for spray painting for panel with one coat of primer and two coats of synthetic enamel paint of smoke grey colour after throughly preparing, cleaning in & out side of the panel complete all as specified and as directed.

S&F 3 core multistranded copper power cable 6 Sqmm for Centrifugal pump sets including necessary connection and testing complete all as specified and directed.

All as per Srlitem No.31 above but 10 Sqmm -ditto-

All as per Srlitem No.31 above but 16 Sqmm -ditto-

Supply , install, testing and commissioning of LT feeder pillar box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , suitable for outdoor use , with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick CRCA steel sheet of IP 65 protection, with angle iron frame work and legs of ISA 50X50X5 mm , with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs , hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated comprising of the following complete all as specified and directed:-

Supply , install, testing and commissioning of LT feeder pillar box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , suitable for outdoor use , with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick CRCA steel sheet of IP 65 protection, with angle iron frame work and legs of ISA 50X50X5 mm , with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs , hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated comprising of the following complete all as specified and directed:-

Supply , install, testing and commissioning of LT feeder pillar box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , suitable for outdoor use , with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick CRCA steel sheet of IP 65 protection, with angle iron frame work and legs of ISA 50X50X5 mm , with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs , hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated comprising of the following complete all as specified and directed:-

Supply , install, testing and commissioning of LT feeder pillar box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , suitable for outdoor use , with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick CRCA steel sheet of IP 65 protection, with angle iron frame work and legs of ISA 50X50X5 mm , with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs , hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated comprising of the following complete all as specified and directed:-

Supply , install, testing and commissioning of LT feeder pillar box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , suitable for outdoor use , with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick CRCA steel sheet of IP 65 protection, with angle iron frame work and legs of ISA 50X50X5 mm , with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs , hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated comprising of the following complete all as specified and directed:-

Supply , install, testing and commissioning of LT feeder pillar box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , suitable for outdoor use , with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick CRCA steel sheet of IP 65 protection, with angle iron frame work and legs of ISA 50X50X5 mm , with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs , hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated comprising the following complete all as specified and directed:-

Supply , install, testing and commissioning of LT feeder pillar box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , suitable for outdoor use , with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick CRCA steel sheet of IP 65 protection, with angle iron frame work and legs of ISA 50X50X5 mm , with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs , hinged doors at front with suitable locking arrangement , Provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated comprising the following complete all as specified and directed:-

Supplying , installing , testing and commissioning of LT feeder pillar box AC 415 V , 50 HZ 3 Phase 4 wire of suitable size for accomodating the following accessories totally enclosed self supporting structure / cubicle , fully compartmentalized type , suitable for outdoor use , with bottom cable entry with suitable cable glands structure made out of 3.15 mm thick CRCA steel sheet of IP 65 protection, with angle iron frame work and legs of ISA 50X50X5 mm , with four legs grouted to PCC (1:2:4) type B1 , foundation block with suitable mounting arrangement for bus bars voltmeter, ammeter , changeover switch and MCCBs , hinged doors at front with suitable locking arrangement , provision of louvers at sides , structure treated under 8 - tank metal treatment process and duly powder coated comprising the following complete all as specified and directed:-

Vinod Enterprises (BID ID -3062644)

M/s PRATAP VIJAYSINGHRAO DESAI (BID ID -3072155)

RAJENDRA KRISHNA SARAF (BID ID -3063315)

M/s ASPIRE ENGINEERING ENTERPRISES (BID ID -3071555)

M/s S N Atiwadkar (BID ID -3063461)

B5BUILDING SOLUTIONS (BID ID -3063306)