REPAIR MAINT TO FLOORING ANTI TERMITE TREATMENT JOINERIES PLUMBING SANITORY FITTINGS FENCING AND SEWAGE LINE AND REPAIR MAINT OF INTERNAL ELECTRIFICATION AND OTHER EM RELATED MAINT SERVICES UNDER GE EAST MATHRA

Amount

Taking down cement plaster of any description from brick wall or concrete surface etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick/ concrete surfaces in cement mortar 1:4 finished the surface even and smooth without using extra cement, mixed with 200 ml water proofing liquid per 50 kg bag of cement complete all as specified and as directed. Note : Water proffing liquid shall be measured and paid separately.

Supply only water proofing liquid complete all as specified and as directed.

M&L for 15mm thick rendering on other than fair faces of brick/concrete surfaces in cement mortar 1:6 finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5 mm thick in CM 1:3 over 10 mm thick dubbing coat in cement mortar 1:4 as on ceiling surfaces of concrete finishing the surface even & smooth without using extra cement complete all as specified and as directed.

M&L for providing damp proof layer in two coats of acrylic polymer coating consisting of 1 part of acrylic polymer liquid mixed with 2 parts of cementious powder applying at the rate of 1.40 Sqm/ Kg of mix per coat. Second coat shall be applied after 4-6 hrs of first coat, out of the surface before providing plastering compete all as specified and as directed. Note : Make of the material 'Smart Care damp block 2K' of Asian paints or equivalent from Dr Fixit/STP/CICA etc. as approved by Engineer-in-Charge.

M&L for prepration of new plastered or unplastered surface of walls and applying two coats of cement base paint complete all as specified and as directed..

M&L for prepration of new plastered or unplastered surface of walls and applying tree coats of white wash complete all as specified and as directed.

M&L for prepration of new plastered or unplastered surface of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for prepration of newly plastered or unplastered surface of wall and applying two coat of distemper oil emulsion over a coat of alklai resitant primer complete all as specified and as directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises compete all as specified and as directed.

M&L for Non Skid ceramic joint free coloured tiles 7 to 8 mm thick, (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement motar 1 : 6 complete all as specified and as directed.

M&L for Glazed ceramic coloured tiles in vertical surface of size 350x250x 7mm/ 450 x 350 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick plaster in cement motar 1:4 complete all as specified and as directed.

M&L for Vitrified Ceramic coloured tiles 10 mm thick (square/ rectagular) polished,area of each tiles not exceeding 0.36 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in cement motar 1:4 complete all as specified and as directed.

All as per item serial No 14 here in before but as in skirting/dado laid over and including 10 mm thick rendering in cement motar 1:4. complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (Below or above ground level) compete all as specified and as directed.

M&L Cement concrete type E2 1:5:10 (using 40mm graded stone aggregate) as in foundations, filling (sunken floor) and mass-concrete complete all as specified and as directed.

M&L for 50 mm thick cement concret type B1 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection, finishing cement concrete surface even and smooth without using extra cement compete all as specified and as directed.

S&F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete, including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim complete all as specified and as directed.

S&F in repair Vitrreous china wash down water closet pedestral pan white, including 10 ltrs PVC valveless, syphonic action type, flushing cistern, low level, white with inlet, ball valve, float and handle including brackets, flush pipe of polythylene of low or high density or PVC 32mm dia, plastic water closet seat, closed pattern with recessed bottom, and cover and mild steel chromium plated or aluminium hanging device, complete all as specified and as directed.

S&F in repair plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete as specified and as directed.

S&F in repairs 10 ltrs PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, aluminium brackets for bottom support etc complete all as specified and as directed.

S&F in repair 32 mm bore Low density polyethylene pipes (LDPE) of pressure rating 6 kgf/ cm2 fixed as waste pipe for WHB/Urinal etc complete all as specified and as directed.

S&F in repair Toilet paper holder of brass, chromium plated fixed to walls with chromium plated (CP) brass screws complete all as specified and as directed.

S&F in repair CP health faucet with 1.00mm long easy flex tube in chrome finish & wall hook suitable for 15 mm dia pipe including making connections and fixed in position complete all as specified and as directed. Make : Cat No ALD-565 of Jaquar or equivalent in Hindware/Cera.

S&F in repairs vitreous china wash hand basin, white, flat back, size 550x400mm including brackets, waste fittings, brass, chromium plated 32mm with long screwed shanks and fly nuts, flanged end bedded in red lead cement and other end fixed, including PVC waste pipe of 32mm bore 75cm long, complete all as specified and as directed.

Taking up or down mild steel tubes galvanized iron 15mm dia bore and connections including cleaning for refixing or removing from site complete as specified and as directed.

M&L for Cutting chases pinning in , making good to facing where reqd. and pointing in cement mortar 1:3 to ends or edges of landing , steps, cills, sunshades,selfs lintels etc. and cutting chases for conceled for water tubing or conceled condute wiring etc and making good, cutting n.exc 10cm girth.complete all as specified and as directed.

S&F mild steel galvanised tube 15mm dia/bore medium grade with all fittings fixed to walls, ceiling or laid in floor complete all as specified and as directed.

Taking up or down mild steel tubes galvanized iron 20 mm dia/bore and connections including cleaning for relaying/refixing or removing from site complete all as specified and as directed.

S&F mild steel galvanised tube 20mm dia/bore medium grade with all fittings fixed to walls, ceiling or laid in floor complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank (Triple layers white in colour) (Cylindrical vertical with close top) hoisted and fixed in position 500 liters capacity including connections and dismantling existing old u/s water storage tank complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank (Triple layers white in colour) (Cylindrical vertical with close top) hoisted and fixed in position 750 liters capacity including connections and dismantling existing old u/s water storage tank complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank (Triple layers white in colour) (Cylindrical vertical with close top) hoisted and fixed in position 1000 liters capacity including connections and dismantling existing old u/s water storage tank complete all as specified and as directed.

S&F ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for 20mm bore dia of pipe and fixed ( Minimum weight 210 gms each) complete all as specified and as directed.

Cleaning of HDPE tank of capacity 1000 litres by Flushing out water cleaning & removing of sludge, scale mud etc from wall & floor by rubbing with brushes, cleaning with caustic soda etc complete & finally washing with fresh water, including writing date of cleaning with white synthetic enamel paint and removing sludge, scale mud etc to a distance not exceeding 50 metre and depositing where directed complete all as specified and as directed.

S&F in repairs cover for HDPE water tank of capacity 500 & 1000 ltrs any type & make rotating type with frame including nut bolt complete all as specified and as directed.

S&F in repairs ball valves high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for 20mm bore dia of pipe and fixed (minimum weight 210 gms each) complete as specified and as directed.

S&F, Gun matel, globe or gate valves with iron wheel head, screwed both ends for iron pipe 20 mm bore dia and fixed all as specified and as directed

S&F in repair bib taps chromium plated cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe 15mm bore dia complete all as specified and as directed.

S&F in repairs chromium plated brass angle valve fancy type screwed both ends high pressure for iron pipe or ferrule 15 mm bore complete as specified and as directed.

M&L for pillar taps, cast copper allloy, with capston heads, chromium plated fancy type, screwed down high pressure, with or without letter hot or cold with long screwed shank and fly nuts, screwed fo iron pipe 15mm bore dia of pipe complete all as specified and as directed.

S&F PVC connection 15mm size with PTMT nut of length 600mm complete as specified and as directed.

S&F in repair wash basin mixer 15mm bore complete as specified and as directed. Make: Cat No : APR-101011B of ESSCO or equivalent in approved list of makes as approved by Engineer-in-Charge.

S&F in repair stop valve cast copper alloy fancy type cromium plated screwed down high pressure with crutch or butterfly handle scrwed both with ends for iron pipe or union and fixed 15 mm dia bore complete as specified and as directed.

S&F in repair stop/gate valve cast copper alloy, chromium plated, fancy type with long sank and cup (concealed type) screwed down high pressure with with crutch or butterfly handle, screwed both ends for iron pipe or union 15mm dia bore and fixed complete all as specified and as directed.

S&F in repair Brass CP mixer for mixing hot & cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified and as directed.

S&F in repair for brass chromium plated tubular towel rail, 20mm dia, ‘D’ type, 60cm long between flange complete all as specified and directed.

S&F in repair PVC cabinet with mirror of size 350 mm x 450 mm, fixed to wall with screw all as specified and as directed. Make:- Prayag Cat No 551 or equivalent of make Commonder / Neelkamal / Polytuff

S&F in repair chromium plated shower rose with 240mm long arm complete as specified and as directed. Make : ESSCO cat no: ALE-536A/EOS-542A as approved by Engr-in-charge.

S&F in repair Harrison rails, mild steel, chromium plated curtain rod 20 mm dia with fixing brackets including CP decorative stops, roller etc complete as specified and as directed.

S&F Stainless steel plate rack made of 1.00mm thick stainless steel sheet for kitchen of size 750x600 mm fixing with stainless steel and with screw on wall complete as specified and as directed.

S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F in repair 75mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

S&F 110mm bore PVC (SWR) bends any radius complete as specified and as directed.

S&F 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal provided with acess door complete as specified and as directed.

S&F 110 mm bore PVC (SWR), vent cowl complete as specified and as directed.

S&F PVC (SWR) bends any radius 75mm bore complete as specified and as directed.

S&F in repair 75mm dia of outlet PVC (SWR) floor trap plain with grating including jointing with solvent cement complete as specified and as directed.

S&F waste coupling of PTMT for 30mm bore discharge pipe (half or full threaded) (minimum weight 45gms) complete as specified and as directed.

S&F waste coupling of PTMT for 40mm bore discharge pipe (half or full threaded) (minimum weight 60gms) complete as specified and as directed.

S&F in repairs PVC flexible waste pipe 32 mm dia complete as specified and as directed.

S&F in repairs PVC flexible waste pipe 40mm dia complete as specified and as directed.

M&L Machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid over and including 15mm thick screed bed in cement mortar 1:4 and jointed with gray cement pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over and including 15 mm tick rendering in cement mortar 1:4 and jointed with gray cement and pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) in steps jambs,window cills, cooking platform and like laid over and including 15 mm thick screed in cement mortar 1:4 pointing in white cement using marbal dust with admixture of pigment to match the colour including rounded/ half rounded edge and hole for gas pipe in pre-cast slab complete all as specified and as directed.

M&L for Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete as specified and as directed.

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete as specified and as directed.

S&F in repairs Stainless steel sink with draining board made out of 1.0 mm thick sheet for kitchen with plug washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe. Overall size 915mmx460mm bowl and size 410x330x160mm complete as specified and as directed.

S&F in repairs 15mm bore Nipple suitable for HDPE water tank minimum weight 38gms complete as specified and as directed.

S&F in repairs 20mm bore Nipple suitable for HDPE water tank minimum weight 45gms complete as specified and as directed.

Taking down chowkhat or frames with shutters without taking off shutters from frame area n.exc 1.50 Sqm each complete as specified and as directed..

Taking down door chowkhat or frames with shutters without taking off shutters from frame area exc 1.5 sqm and n. exc 4 Sqm each complete as specified and as directed..

S&F Pressed steel frame size 105 X 60 mm for doors with one or more rebates including necessary fixing lungs, hinges, lock strike plate, etc, supplied and fixed complete all as specified and as directed.

S&F Pressed steel frame size 125 X 60 mm for doors with one or more rebates including necessary fixing lungs, hinges, lock strike plate, etc, supplied and fixed complete all as specified and as directed.

M&L for cement concret 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) as in filling of pressed steel frame complete all as specified and as directed.

S&F 30 mm thick, Flush shutters, solid core construction, with block board core and plywood face panels, commercial type both face covered with decorative face veneer with lipping/frame to match on both sides complete all as specified and as directed.

S&F 30 mm thick factory made glazed and skeleton shutters of 2nd class HW, open rebated and prepared to receive glass/gauze etc edges or framing plain chamfered or rounded fitted with cut or mitred beads for securing glass etc as specified in SSR Part-1 section 8.20 (a) complete as specified and as directed.

S&F Solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles) with 2, 4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face with wood free EPS complete as specified and as directed.

S&F 150 mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F Aluminium handles,fabricated type, anodised 150 mm long complete as specified and as directed.

S&F 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete as specified and as directed..

S&F floor door stopper of aluminium alloy body and tongue overall length of cover plate 150 mm, anodised with hard drawn steel spring fixed in floor complete as specified and as directed..

S&F 300 mm, mild Steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded ccomplete all as specified and as directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

S&F 4 mm thick sheet glass, ordinary quality and glazing fixed in repairs to aluminium/ Steel/ wooden frame in square exc. 0.5 square metre in each pane complete as specified and as directed.

S&F 4mm thick frosted glass, ordinary quality and glazing fixed to aluminium frame in square exc. 0.5 square metre in each pane complete all as specified and as directed.

M&L Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete as specified and as directed.

S&F in repairs Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples/ screwed complete all as specified and as directed.

M&L for prepration of new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamal paint over a coat of red oxide primer complete as specified and as directed.

M&L for Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area using chemical chlorophyriphos or lindane emulsifiable concentrate 20EC conforming to IS:8944 or IS 632 complete all as specified and as directed.

M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical chlorophyriphos or lindane emulsifiable concentrate 20EC conforming to IS:8944 or IS 632, emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed.

M&L for Treatment of soil under existing floors using chemical chlorophyriphos or lindane emulsifiable concentrate 20EC conforming to IS:8944 or IS 632, emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete as specified and as directed.

Dismantling fencing wire mesh, any type complete as specified and as directed..

Excavatoin in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm as in soft/ loose soil complete as specified and as directed.

M&L for Cement Concrete 1;3:6 type C-2 (using 40 mm graded stone aggregate) as in foundation filling & mass concrete etc complete all as specified and as directed.

S&F MS angle iron posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc flat iron fillet (for securing wire mess etc) and similar works confirming to Fe-290 Gde E-165 complete as specified and as directed.

S&F mild steel screw bolts (machine made) dia of 5 to 10mm including all necessary dwelling bolting or riveting etc with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete as specified and as directed.

S&F mild steel round bars 10mm dia cut to length, bent to shape required bent to shape required and fixed in fencing grade-I IS-432 (Part-I) Part-I complete all as specified and as directed.

S&F Mild steel work as in hand rails , half round or other section, balusters running bars, nosing to steps, wind ties, posts and struts in fencing incl cutting tops to shape as required, drilling holes, noching for wire, flat iron fillets for securing wiremesh etc., incl all necessary drilling, bolting or riveting etc & similar work conforming to Fe-290 Gde E-165 and complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete as specified and as directed.

Supply only MS galvanised chain link wire mesh 100mm x 100 mm size of mesh as in fencing with 3.15mm dia galvanised steel wire complete as specified and as directed.

S&F in repair galvanised 2 strand steel barbed wire 2.24mm, dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provn of galvanised mild steel wire staples or steel pins complete as specified and as directed.

Cleaning of sewage lines which are blocked /filled with sludge, semi solid/material etc by roding manholes to manholes manuually or by cleaning machine removing the sludge to a non inhabitant area or buried into ground all as specified for the following internal dia of pipe complete as specified and as directed:- Note :- (i) Sewage line cleaned should function smoothly during entire contract period and measurement shall be made only once. (ii) Contractor shall be responsible to clear any further blocagkage without any extra payment till completion of work.

150 mm bore dia.

200 mm bore dia.

Dewatering effluent completely from soak well of any capacity by means of sludge pump machine, drainage or made drain complete as specified and as directed.

Desilting completely from septic tank and removing the Sludge through covered vehicle to a non inhabitant to a distance exc 1.0 km and n.exc 1.5 kms area and buried into ground complete as specified and as directed.

Cleaning of blockage of any type of wc (Indian/pedestal) from WC pan to Ist manhole in single/double storied bldg including resetting/ refitting of asccess door in soil pipe where open without causing any damage to the wc pan 'P' OR 'S' trap and pipe fitting complete all as speciffied and as directed.

Cleaning of blockage of any type in Nahani trap provided in bath room, kitchen and indoor water pipe of kitchen sinks and WHB and removing all the sludge and foreign material from the trap and waste pipe from blocked trap to gully trap/ surface drain wherever opened or without causing any damage to the trap and pipe including fitting distance of gully trap from outer wall of bldg upto 2m complete all as specified and as directed.

Excavation in trenches in soft/ loose soil exc 1.5 m deep and getting out including forming bottom to required level or slop for laying pipe, concrete bed manhole etc n.exc 10 Sqm on plan complete all as specified and as directed. Note: Pipe and concrete bed shall be measured and paid separately.

All as per item Serial No.114 here in befoe but exc 1.5 deep and n.exc 3 m deep complete all as specified and as directed.

M&L Cement concrete 1:4:8 Type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm dia pipe complete all as specified and as directed.

Demolition of breaking up 150 mm dia drain pipe including fittings of any desciption and position and removing rubbish upto a distance of n. exc 50 mtr complete all as specified and as directed.

M&L salt glazed stone ware drain pipe 150 mm bore grade 'A' laid in trenches and jointed with cement mortar 1:1 complete all as specified and as directed.

Demolition of breaking up 200 mm dia drain pipe including fittings of any desciption and position and removing rubbish upto a distance of n. exc 50 mtr complete all as specified and as directed.

M&L cement concrete 1:4:8 Type D-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm dia pipe complete all as specified and as directed.

M&L salt glazed stone ware drain pipe 200 mm bore grade 'A' laid in trenches and jointed with cement mortar 1:1 complete all as specified and as directed.

Returning filling in soft/loose soil including spreading levelling ,watering and well ramming in layers not exc 25 mm thick complete all as specified and as directed.

Removing of excavated surplus materials to a distance exc 50 m but nexc 100 mm and depositing where directed a level n.exc 1.5 mtrs above the starting point complete all as specified and as directed.

Demolition of brick work of any description and position built in cement mortar and removing rubbish upto a distance of n exc 50 mtr complete all as specified and as directed.

M&L for brick work with sub class 'B' bricks straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M&L half brick thick brick work with sub class ‘B’ built in cement mortar1:4 complete all as specified and as directed.

Demolition of reinforced cement concrete as in cover slabs of any description, removal of debris out side MD land complete as specified and as directed.

M&L reinforced cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floor, roof, beams and shelves etc for soak well/septic tank in running and manhole cover slab with plain fair faces and set in cement mortar 1:4 condition complete all as specified and as directed.

M&L for use & waste form work to soffits of suspended slabs such as roof slabs, landing and similar work n exc 200 mm thick, (Horizontal or sloping) for rough finished surfaces complete all as specified and as directed.

M&L deformed/twisted mild steel bars 6 mm to 8 mm dia cut to length, bent to shape required, including cracking, bending,spirally for hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

S&F for deformed mild steel bar or TMT bars 10 mm dia and over in reinforcement cut to length bent to shape reqd incl crancking, bending, binding, hooking end etc and binding with MS annealed with MS binding wire not less than 0.9 mm dia including supply of binding wire complete as specified and as directed.

All as per item serial No 131 above but mild steel round bar 10 mm dia and over as in handles of manhole covers complete all as specified and as directed.

Taking down unserviceable ceiling fans/exhaust fans of any make and type and rectifying the defects including replacement of unserviceable parts and testing and reinstalling at same or any other location complete as specified and as directed. Notes - (i). The unit rate is deemed to include the cost of taking down carefully fans from existing position after disconnecting electric connections, sealing cable ends,replacement old copper wire of 1.5sqmm size upto 1mtr bringing to MES store yard. (ii) Cost of major items such as ball bearing, gun metal bush, capacitors, blades, canopy and repair/ rewinding /painting etc shall be measured and paid separately under relevant item of this schedule as supply only. (iii) Minor items or works like tightening loose connections in switch, binding insulation tape to the naked wires, replacement of unserviceable clamps, nuts and bolts, split pins, rubber reel, washers etc will be provided without any extra cost and cost of these minor items or works will be deemed to be included in the quoted rates against this item.

Supply only bush made out of Gun metal suitable for ceiling fan/exhaust fan as required at site complete all as specified and as directed.

Supply only shaft of approved quality for ceiling fan as per existing make, type and size complete all as specified and as directed.

Supply only canopy suitable for ceiling fans of any make, type and size complete all as specified and as directed. Make: Usha/Bajaj

Supply only Rubber reel with clamp including split pins and nuts, bolts for ceiling fans complete all as specified and as directed.

Supply only down rod MS grade 15 mm bore of length upto 75 cm size for ceiling fans of any type and size including cutting, drilling holes, making thread and painting complete all as specified and as directed.

Supply only capacitors 2.5 MFD suitable for all types of fans complete all as specified and as directed. Make: - Usha/Universal/Epcos/L&T/ABB/GE

Supply only capacitors 4.0 MFD suitable for all types of fans complete all as specified and as directed. Make: - Usha/Universal/Epcos/L&T/ABB/GE

Supply only SKF 6201 ball bearing suitable for ceiling fan of any type as required including proper alignment of shaft and testing complete all as specified and as directed.

Supply only SKF 6202 ball bearing suitable for ceiling fan of any type as required including proper alignment of shaft and testing complete all as specified and as directed.

Supply only SKF 6203 ball bearing suitable for exhaust fan of any type as required including proper alignment of shaft and testing complete all as specified and as directed.

Dismantling of worn out/burnt out windings of ceiling fan and re-winding the motor of ceiling fan with super enamelled copper wire of existing gauge, varnishing with approved quality insulating varnish complete including replacement of split/safety pins, locking nut, check nut and testing for original and consumption complete all as specified and directed for following sizes:-

1200 mm sweep.

1400 mm sweep.

Dismantling of worn out/burnt out windings of exhaust fan any type and re-winding the motor with super enamelled copper wire of existing gauge, varnishing with approved quality insulating varnish complete and testing for original and consumption complete all as specified and as directed for following sizes:-

200/230 mm sweep.

300 mm sweep.

450 mm sweep.

Material and labour for spray painting ceiling fan 1200 mm/1400 mm with blades 3 Nos of any type and applying one coat of synthetic enamel paint by spraying including filling cavities with filler, after cleaning all dusts including writing of MES Nos in black paint complete all as specified and as directed.

Material and labour for spray painting to exhaust fan with blade of any type and size with one coat of synthetic enamel paint as approved by Engr-in-charge including filling cavities with filler, after cleaning all dusts including writing of MES Nos in black paint complete all as specified and as directed.

Supply and fixing in replacement ceiling fan blade of type and make as existing complete all as specified and as directed at site of following sizes:-

1200mm sweep

1400mm sweep

Supply and fixing in replacement step type electronic fan regulator switch type on the existing phenolic laminated sheet including taking down the old unserviceable one complete all as specified and as directed. Make : Havells/Orient/Bajaj/CG/Philips

Supply and fixing in replacement step type electronic fan regulator socket type on the existing phenolic laminated sheet including taking down the old unserviceable one complete all as specified and as directed. Make : Havells/Orient/Bajaj/CG/Philips

Supply and fixing in replacement step type electronic fan regulator modular type on the existing laminated sheet including taking down the old unserviceable one complete all as specified and as directed. Make : Havells/Orient/Bajaj/CG/Philips

S&F PVC insulated sheathed 1.5 sqmm 3 core cable 1100 volts grade ISI marked copper conductor complete all as specified and as directed. Make : Havells/RR Kable/Polycab/Gloster

S&F PVC insulated sheathed 2.5 sqmm 3 core cable 1100 volts grade ISI marked copper conductor complete all as specified and as directed. Make : Havells/RR Kable/Polycab/Gloster

Taking down existing copper / aluminium point wiring (Light / Fan / Socket or Power Point) complete, (fittings such as switches, ceiling roses, pendants, regulators, sockets), removing materials from site and making good the disturbed surfaces of walls, floors etc as per existing specification complete all as specified and as directed.

Taking out existing copper/aluminium sub main wiring of any size and making good the disturbed surfaces complete all as specified and directed.

M & L for Point wiring with 1.5 Sqmm (nominal area) single core PVC insulated unsheathed FRLS cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia med gd)and its all accessories complete concealed in wall / roof incl cutting & chases( making good all to the disturbed surfaces as per existing) and including with flush metal boxes with sheet suitbale for mounting switches, socket, regulator etc and including earth wire of PVC insulated FRLS copper conductor multistranded of 1.5 Sqmm size in green colour for one light/fan/bell point controlled by one switch complete all as specified as directed. Make : Havells/Polycab/Finolex/RR Kable/Plaza

One light/fan point controlled by one way switch 5 amp complete all as specified and as directed.

All as per item Serial No 156 but surface conduit/casing caping wiring complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one switch on independent board complete all as specified and as directed.

One 3 pin 5 Amps socket point controlled by one way switch on same board complete all as specified and as directed.

One light point controlled by two 2-way switches complete all as specified and as directed.

M & L for Point wiring with 2.5 Sqmm (nominal area) single core PVC insulated unsheathed FRLS cable, multi-stranded, copper conductor, in universal colour code with & including suitable size of rigid non-metallic PVC conduit (not less then 20mm dia medium grade) and its all accessories complete concealed in wall/roof incl cutting & chases making good all to the disturbed surfaces as per existing and including with modular flush metal boxes with modular cover plates & frame for mounting modular switches, sockets, regulators etc and including earth wire of PVC insulated FRLS copper conductor multistranded of 2.5 Sqmm size in green colour complete all as specified in current SSR Part-I & II complete all as specified and as directed. Make : Havells/Polycab/Finolex/RR Kable/Plaza

Supply and Fixing switch piano flush type 5 Amps single pole one-way complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

Supply and Fixing socket outlet flush type 2-in-1, 3 pins 5 Amps multipurpose complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

Supply and Fixing switch flush type 2-in-1,3 and 5 pins 15 Amps multipurpose complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

Supply and Fixing socket outlet flush type 2-in-1,3 and 6 pins 15 Amps multipurpose complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

Supply and Fixing switch piano flush type 5 Amps single pole two-way complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

Supply and Fixing ceiling rose surface bakelite 65mm x 50mm three terminals complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

Supply and Fixing bell Push switch flush type 6 Amps single pole one-way complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

Supply and fixing Bell Multi Music type, 230 Volts with connection complete all as specified and as directed. Make : Havells/Orient/Bajaj/CG/Philips

S&F in repairs of Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor FRLS cable of size 6sqmm, 1100 votls grade drawing through concealed PVC conduit 20 mm dia medium duty and including PVC insulated 6sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly complete all as specified and as directed. Make : Havells/Polycab/Gloster Note : Two runs of 6 Sqmm cable, one run of 6Sqmm earth wire & 20mm PVC Conduit shall be measured as one unit length.

S&F in repairs of Sub main wiring with two single core cable PVC insulated unsheathed of copper multi strandard conductor FRLS cable of size 4 sqmm, 1100 votls grade drawing through concealed PVC conduit 20 mm dia, medium duty and including PVC insulated 4sqmm unsheathed multistranded FRLS copper conductor cable for earth continuity and connected to common earth dolly complete all as specified and as directed. Make : Havells/Polycab/Gloster Note : Two runs of 4Sqmm cable, one run of 4Sqmm earth wire & 20mm PVC Conduit shall be measured as one unit length

Material and labour for Earthing complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level ) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI wire 4.0 mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and incl 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and chaarcoal filling, necessary excavation and earth work complete all as specified and as directed.

S & F factory made epoxy powder coated Distribution Board TP&N 4 ways TPN MCB DB with metal door ( IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with Knockouts complete all as specified and as directed. Make : Havells/L&T/Legrand/Simens/Schenider.

S&F 4 Pole TPN MCB 63 Amps ,415 V, 50Hz, with repturing capacity 16 KA complete all as specified and as directed. Make : Havells/L&T/Legrand/Simens/Schenider.

S&F factory made epoxy powder coated Distribution Board SPN 8 ways (SPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with Knockouts complete all as specified and as directed. Make : Havells/L&T/Legrand/Simens/Schenider.

S&F factory made epoxy powder coated Distribution Board SPN 4 ways (SPN MCB DB ) with metal door ( IP-43 protection) fabricated from minimum 1.6mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removeable gland plates with Knockouts complete all as specified and as directed. Make : Havells/L&T/Legrand/Simens/Schenider.

S&F SPN MCB 40 Amps, 240 V, 50Hz, 10KA breaking capacity complete all as specified and as directed. Make : Havells/L&T/Legrand/Siemen/Schneider/ ABB/ C&S/HPL

S&F SP MCB 6-32 Amps, 240 V, 50Hz,10KA breaking capacity complete all as specified and as directed. Make : Havells/L&T/Legrand/Siemen/Schneider/ ABB/ C&S/HPL

S&F in replacement of Ceiling fans of size 1200mm sweep, BEE, 5 star rated complete 230 Volt, including hanging arrangement at site complete all as specified and as directed. Note : Depositing the old ceiling fans in MES store yard complete.

S&F in replacement of exhaust fan heavy duty 300 mm AC 230Volt Metal body single phase including louvers Make : Havells Note : Depositing the old exhaust fan in MES store yard complete.

S&F in replacement of indoor decorative ultra slim surface /Wall mounted aluminium extruded T5 LED batten tube light complete fitting 1x 18 watt 4' LED Tube fitting complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

S&F in replacement of environmental friendly, ultra modern, energy saving, surface mounted, Bulk Head fitting of 10 Watt complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable with suitable size of complete all as specified and as directed. Make : Surya Cat Part No SLE BH 10W or equivalent make in philips/Havells.

S&F in replacement of LED T-5 Intergrated Batten PC housing extruded 2' light fittings 14 w complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

S&F in replacement of LED T8 Tube 20w with aluminium extrusion heat sink for optimum performance complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

S&F in replacement of building street light fitting, IP66 powder coated pressure die cast aluminium with heat resistant toughened glass complete of 36 Watt capacity including fixing arrangement complete with all accessories including connecting up with twin core copper conductor cable with suitable size complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

S&F 40 mm dia tube medium grade galvanised with all fitting and fixed complete in/on the wall ,roof for hanging of fan with fan hook including making good the disturbed surface to match with the existing complete all as specified and as directed. Make : Jindal/TATA/PRAKASH

S&F LED retrofit lamp 9 Watt complete all as specified and as directed. Make : Havells/Bajaj/Crompton/Philips/C&S/Surya.

Supply and fixing Lamp holder, PVC / polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F SPN/2 pole RCBOs 32 Amp , 100 mA, 230volt 10kA complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as specified and as directed. Make : Havells/Legrand /L&T/Siemens/Schnieder

Supply and fixing hook for hanging ceiling fan confirming to Fe-290 Gde-E-165, size as per site requirements including nut, bolts & clamps complete all as specified and as directed.

S&F switch modular type 6 Amps complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F socket modular type, single pole one module 6 Amps 230v complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F switch modular type, single pole one module 16 Amps 230v complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F socket modular type 2-in-1, 5 Pin, 6/16 Amps 2 module complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F modular bell push switch 6 A, 1 Module complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F in repair modular sunkun box 3 module with modular 5/15 A switch& socket complete with cover plate set including PCC m-15 grade using 20mm graded stone aggregate and making good the disturbed surface with existing complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F in repair modular sunkun box 1 module with modular 5 A switch complete with cover plate set including PCC m-15 grade using 20mm graded stone aggregate and making good the disturbed surface with existing complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F in repair modular sunkun box 6 module complete incl fixing modular switchs,sockets regulator with cover plate set including PCC m-15 grade using 20mm graded stone aggregate and making good the disturbed surface with existing complete all as specified and as directed. Make : Havells/Anchor(Roma)/Legrand/Honeywell/ Polycab/Crabtree

S&F LED Round recess mounted downlighter with die cast aluminium housing 24w complete all as specified and as directed. Make : Havells/CG/Philips/Wipro/Syska/Bajaj

Ms Kamal Kant Agarwal

M/s Hoti Lal Contractor

BHARDWAJ CONSTRUCTIONS