Upgradation of Birsa Stadium, Saraikela District

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classfication of soil item - A) and disposal of excavated earth a obtained to a distance up to 50M including all lifts with leveling ramming the foundation trenches removing roots of trees shurbs all complete as per approved design and per building specification and direction of E/I.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item - B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts includng cost of all materials, Labour, rotalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume).

Providing designation 75B brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening maerials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Providing R.C.C. M-200 in band at plinth level with nominal mix of (1:1.5:3)

Providing and laying 25 mm thick kotah stone slab flooring of approved size, texture and colour over 19 mm thick base of lime mortar (1:1:1) (lime putty: surkhi : coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I

Providing and laying 25 mm thick kotah stone tiles in risers of steps, skirting and pillars of approved size, texture and colour laid over 12 mm thick base of cement mortar (1:3) and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I kotah stone tiles in risers os steps, skirting and pillars of approved size,

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Supplying, fitting and fixing 30mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

35 mm Thk. Factory made POLYVINYL Choride PVC Door Shutter made of Styles and rains of a UPVC hollow Section of size 60x30mm and wall thickness2mm(+-0.2mm) with inbuilt decorative moulding edging on one side.The styles and rails mitred and joint at the corners by means of ms .galvanised/plastic brackets of size 75x220mm having wall thickness 1.0mm and stainless steel screw.The styless of the shutter reainforced by inserting galvanised M.S tube of size 25x20 mm and 1mm(+-0.1MM) Wall thickness. The lock rail made up of h section a upvc hollow section of size 100x30 mm and 2 mm (+ 0.2 mm) wall thickness fixed to the shutter styles by means of plastic galvanised M.S.u cleats the shutter frame filled with a upvc multi chambred single panel of size not less than 620mm having over all thickness of 20mm and 1 mm (+0.1mm) wall thickness the panels filled vertically and tie bar at two places by inserting horizantally 6 mm galvanised M.S road and fastened with nuts washers complete as per manufacture's specification and direction of Engineer -in-charge.POLYVINYL Choride PVC Door Shutter made

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5 mm, made out of extruded 5mm extrude rigid pvc foam sheet, mitred at corners and joimed with 2 nos of 150 mm long brackets of 15x15mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm MS.square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame.The door frame The door frame to be fixed to the wall using M.S. screws of 65/100mm size, complete as per manufacture specification and direction of Engineer-in-charge.

Providing Toe steel reinforcement of 8mm dia to 32mm dia rods as approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (Only Valid for SAIL & TATA STeel)

Providing designation 75 B one brick flat soling joints filled with local sand including cost of watering texes royalty all complete as per building specification and direction of E/I.

Providing and laying 6 mm precast white glazed tiles in walls over 12 mm cement mortar (1:3) and jointed with with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing taxes, and royalty all complete as per building specification and direction of E/I with grade A coloured 15cm x15cm tiles.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5mm cement punning including curing, carraige of water with all leads and lifts as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone orfine and paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Dismantling old plaster and pointing in cement or lime and raking out joints to 15mm depth, watering and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Taking down old door and window shutters including stacking and serviceable materials within 15m lead and disposal of unserviceable materials with all leads all complete as per direction of E/I

Taking down chaukhats in doors including stacking serviceable materials within 15M,. Lead and disposal of unserviceable materials with all leads all complete as per direction of E/I.

Stone tile work for wall lining upto 10 m height with special adhesive over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including pointing in white cement with an admixture of pigment to match the stone shade. Raj Nagar plain white marble/ Udaipur green marble/ Zebra black marble

Providing and fixing pressed steel door frames conforming to IS: 4351,manufactured from commercial mild steel sheet of 1.60 mm thickness,including hinges, jamb, lock jamb, bead and if required angle threshold ofmild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressedmild steel welded or rigidly fixed together by mechanical means, includingM.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplateand shock absorbers as specified and applying a coat of approved steelprimer after pre-treatment of the surface as directed by Engineerin-charge: Profile B- Fixing with adjustable lugs with split end tail to each jamb

Steel work in built up tubular (round,square or rectangular hollow tubes etc.) trusses etc. including cutting,hosting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc.complete Hot finished seamless type tubes

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat and paint of approved steel primer all complete.

Providing and laying rectified glazed ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacture) of 1st quality conforming to IS 15622 of approved make in all colours shades except white lvory, Grey Fume red brown laid on 20 mm thick cement mortor 1:4 (1 cement: 4 coarse sand), jointing wth grey cement slurry 3.3kg /sqmm including pointing the joints with white cement and matching pigments etc, complete.

Providing and laying Double Charge vitrified floor tiles in Different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and confirming to IS 15622/ISO 13006, of approved make , in all colour and shades laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointed with grey cement [email protected] kg /sqm including grouting the joints with white cement and matching pigment etc.Size of tiles 600x600mm

Providing corrugated G.S. sheet roofing including vertical / curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 0.63 mm thick with zinc coating not less than 275 gm/ m²

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

110mm shoe

75mm shoe

110mm bend

75 mm bend

sw gully trap

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete110 mm

Finishing walls with Acrylic Smooth exterior paint of required shade New work(Two more coat [email protected]/10 sqm over and including priming coat of Exterior primer [email protected] kg/10sqm) Acrylic Smooth exterior paint (OUTER)

Providing applying plaster of paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth copmlete.

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surfaceto prepare the surface even and smooth complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete. On concrete work

Finishing walls with Acrylic Smooth exterior paint of required shade : 13.111.1 Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion - Powder coated aluminium (minimum thickness of powdercoating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

Providing Boulder of Size 150mm and below soling in road …do ..all completet job

Labour charge for pitching with stone with stone boulder do all completet job

Shaliltex board(For use as per expansion joint I.S. 1838-1938 Filter)

Carriage of Materials

Bricks Lead = 1k+7P(8km)

Sand lead = 10 km

Stone chips lead = 22 km

GOOD earth-2 km

Boulder-22 km

Stone metal lead = 22 km

Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.

Horizontal - 32 mm dia

Vertical -(iv) 32mm dia weiqht not less than 600qms.

v) 40mm dia weiqht not less than 700qms

(iii) 25mm dia weiqht not less than 375qms.

Cutting chhajja or corince for laying G.I. / C.P.V.C pipe and restoring the same with R.C.C. (1:2:4) brick work in cement mortor (1:4) as per specification and direction of E/I.

Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I.

125 mm thick wall

250 mm thick wall

Supplying, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Mirror of 6 mm thick plate glass bevelled edge mirror including C.P. brass remolving fitting 3 mm ply wood board and C.P hinges to fix with Mirror (600 x 450mm)

C.P. brass soap container medium quality with screw and hinges etc.

Supplying, fitting and fixing viterious white glazed earthen ware I.W.C. of parry Hindustan or any other I.S.S. approved make with 100mm H.C.I. 'p' trap 15 litres C.I. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings C.I. or C.C. brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair or viterous white glazed earthenware footrest to be fixed in floor 15mm C.I. body brass spindle stope cock of weight not less than exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/I. 580mm long - With 12.5 lit. low level PVC cistern

Supplying, fitting and fixing 40mm highb viterous white glazed earthen E.W.C. with 'P' trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fitting with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stope cock of approved quality weight not less than 450 grams 15mm PVC alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic soild state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming all complete as per specification and direction of E/I. With 'P' trap - 12.5 lit low level PVC Cistern

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of exacavted earth within initial lead and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/I. (i) For classification of soil item-A 75x 0.450 x 0.600

Approved basic rates construction materials for preparation of schedule of rates only, (Material should conform to relevent B.I.S. specification). The rates are inclusive of all taxes, royalty, cess and carraige but exclusive of contractor's profit and overhead charges - Special type of C.P. Bath room fitting for V.I.P. buildings (JAL, Jaguar, Marc or equivalent mark)

(iv) Bib Cock (Long Thread) (lSl Marked)

(ii) Pillar Cock (Long neck) (lSl Marked)

(vi) Angular Stop Cock (Long Thread) (lSl Marked)

(xxv) Toilet Paoer Holder

(xxvi) Glass Shelf 22"

(xxi) Towel Rail24"

(xxiii) Soap dish

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required :

White Vitreous China Wash basin size 630x450 mm witha pair of 15 mm C.P. brass pillar taps

Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall

25 mm nominal outer dia Pipes

32 mm nominal outer dia Pipes

40 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.

15 mm nominal outer dia Pipes

20 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet : 150 mm diameter

Providing and fixing PTMT grating of approved quality and colour.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design.With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

Power Plug wiring in PVC Conduit (2X4 Sq.mm) :- Wiring for light/power plug with 2x4 Sq.mm FR PVC insulated copper conductor songle core cable in surface/recessed PVC conduit along with 1 No. 4 Sq.mm FR PVC insulated copper conductor single core cable for loop earthing etc. as required.

Circuit/Sub-main wiring in PVC Conduit:- Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sqmm earth wire

2x4.0 Sqmm + 1x2.5 sq mm earth wire

4x4 Sqmm + 2x4 sqmm earth wire

4 X 10 sq. mm + 2 x 6 sq.mm Earth Wire

Supplying and fixing of following sizes of PVC conduit alongwith the accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required for Tele, RJ45 Cat 6 data outlet for computer network.20 mm

S/F Modular type switch socket - Supplying and fixing following modular switch/socket on the existing modular plate and switch box including connection but excluding modular plate etc. as required

5/6 amps, one way switch

3 pin 5/6 amps, socket outlet

S/F Modular type Switch / Socket: Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required. TV antenna socket outlet

S/F Modular type electronic fan regulator:- Supplying and fixing stepped (two module) type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

Supplying and fixing following size / modules GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 module (78 mm x 78 mm x 45 mm)

S/F light plug point with modular type accessories - Supplying and fixing suitable size G.I. box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch connection, painting etc. as required . (For light plugs to be used in non residential buildings)

S/F power plug point with modular type accessories:- Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

S/F Ceiling Rose:- Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

Installation of exhaust fan upto 450mm sweep in the existing opening, including making the hole to suit the size of he above fan making good the damage, connection, testing, commisionig etc as required.

S/F SP MCB DB: Supplying and fixing of following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (Without MCB/RCCB/ISOLATOR). 12 ways Double Door -for lighting

S/F TP MCB DB: Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (Without MCB/RCCB/ISOLATOR).

4 Way (4+12) Double Door, Horizontal type

6 Way (4+18) Double Door, Horizontal type

S/F 'C' series SP MCB:- Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required. Make- Legrand/Schneider/ Siemens.

6/32A Single Pole

40A DP MCB for outer light

63A rating, TPN MCB, "C" curve 10 KA breaking capacity.

40A rating, TPN MCB, "C" curve 10 KA breaking capacity.

Supplying and fixing 20 amps 240V, SPN industrial socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 amps "C" curve, SP MCB insheet steel enclosure on surace or in recess with chained metal cover for the socket outlet and complete with connections, testing & commissioning etc.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required

P/F 25 x 5mm GI earth strip in ground :- Providing and fixing 25mmx5mm GI earth strip in surface / recess as earth strip electrode including soldering welding etc. as required.

MV Cable Laying upto 25 Sq mm in ground:- Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc, as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of l.l KV grade of size exceeding 95 sq mm but not exceeding 185 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed/ XLPE power cable of l.l KV grade of size not exceeding 35 sq mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as requir

Supply and fixing of 45/48W LED street light fitting ,with die cast aluminium housing of ingress protection of IP65 and complete with all accessories etc on pole including connection and earthing the body etc as required. Make- Bajaj/ Philips/ Havells.

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50H2, single phase supply etc. complete as required. 20/22W LED Tube light including making good the damage, connection testing, commissioning etc as required( Make- Polar/Bajaj/ Havells/Crompton)

S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 1C[.Z70Y AC,50Hz. Luminarie shall be confirm tolS:,1,0322part-5/section-5 and shall be complete with all neccssary accessories as required 75l80W LED Flood light ( make Havells/Bajaj/ Philips/Wipro)

4CX10 sq. mm armoured AL Cable.( for street light)

Supply of 12" (300mm) metal exhaust fan

3.5 Core 120Sq mm (DG supply)

Supply of Decorative Ceiling Fan: Supplying and fitting of 1200 mm Sweep regular/ decorative model AC ceiling fan , including connection with 1.5 sq mm copper wire, down rod of standared length(upto 30cm) withall accessories as required. Make :- Polar/Bajaj/Crompton / Havells / GEC.

Supply of Metal Exhaust Fan 12"(300mm): Supply of 12"(300mm), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required( Make- Polar/Bajaj/ Havells/Crompton)

installation, Testing & Commissioning of the 7 Mtr. Octagonal Pole & light fitting with the help of suitable tools and plants, and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10T/mhs sq. but excluding wire and MCB

Slim Downlighter(Surface) 6W LED: Supply erection and commissioning of LED 6W, ultra sleek surface-mounted, round round LED downlight with all accessories as required. ( make : Wipro/Bajaj-BGSLO SLEEK 6W SURFACE WH RD OR Euivalent)

LED Post top of 25W : Supply and fitting of LED post top made in die cast aluminium housing with decorative opal polycarbonate diffuser IP65 protection. Model - Bajaj-BGCT 25LED or equivalent)

Supply of 125 kVA 415 Volts (3-Phase) DG Set comprising of Cummins make engine model 6BTAA5.9G13 and Genset model-CJ125D5P and 125 KVA Stamford make alternator mounted on a common base , complete with: a) Fuel tank. b) Batteries and leads. c) Manual Control Panel. d) Residential Silencer e) First fill of lube oil f) AVM Pads g) PC1.1 h) Acoustic Enclosure

Material for panel- 14SWG(2mm) CRCA sheet steel including fabrication base channel as per required size with nuts bolts and wahers including seven tank treatment of CRCA sheet followed by finishing powder coating painting of min 60 micron thickeness, covered by soft rubber gasket locking arrangement etc as required.

Outdoor Feeder Panel: Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of suitable size ,earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. All inter connections shall be made with 2.5, 4 & 6 Sq mm PVC Cu. wire.

Incomer

MCCB, 4P, 63A, 25kA

Outgoings

MCB, 4P, 40A, 16kA - 4 nos

Chemical Earthing Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing)

Each chemical earthing shall have following details:-

Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each

Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed).

Supply of Stainless Steel "U" Bolt Clamp

Split AC-1.50T -3 Star : Supply, installation , testing and commissioning of 1.50 TR , 230 V, 50Hz split Airconditioner 3 star rating. Make Hitachi/ Bluestar/ Daikin)

Voltage Stabilizer-5.0kVA : Supply, installation , testing and commissioning of 5.0kVA stabilizer, operating voltage 130V to 280V, single phase for all 2.0T AC. Make-V-guard/Philips/Bluebird

Copper refrigerant piping: Hard drawn suction line with insulation+ Liquidline

PVC Drainline 1": Supply and installation of 1" hard PVC drainline for indoor unit of split AC

Supply of 7 metre hot dip galvanised Octagonal pole(BOP-7030) with top dia 70mm, bottom dia 130mm & made of 3 mm thick sheet, base plate dimensions 200 x 200 x 12 mm(LXBXT) including suitable sizes of foundation bolt all complete as reqd. (without arm)

Supply of 0.5m single arm suitable for 70mm top

Supply Of 800 W LED Sports Light Product Technical Specification : - - Lokozo Part No : CANIS - Z - 800W - Power : 800W. - IP Rating : IP 66. - Operating Voltage : 180 V to 265 VAC. - LED : OSRAM / CREE. - LED Efficacy : 157 lm/W. - Colour : Cool White. - Colour Temparature : 5500K to 6500K. - LENS : 60D / 45D / 15D - BIS Approved Lights.

Supply Of 30 Mtr Mast Pole With Ladder -Suitable For 24 Nos of 800W Luminary Mounting Structure. -Suaitable for Foundation Bolts for 30 Mtr pole.

Supply of GI earthing of suitable size as per requirement per mast

Supply and installation of LED Aviation Light

Supply of Cables and other accessories: 1. Control Panel 2. Driver placed at the bottom of the pole inside the control panel 3.Terminal Block , Circuit Breaker etc. 4. Each light will be provided with separate MCB and control from the control panel 5. Master Box with locking system 6. MCCBs/MCBs, contactors 7. 3C 2.5 sq.mm Copper cable between control panel and lights

i. Grouting (Foundation and Civil work including materials) ii. Grouting of the Control panels. iii. Earthing Pit for panels. 4. Includes JCB Rental Charges

i. 2 Ft Digging of earth for laying Of cables - 540 Meters ii. Cable laying

Erection and Commissioning of the System - It includes: i. Erection of the MAST ii. Erection of the Light mounting arrangements ii. Installation of Lights iv. Cabling to all lights v. Adjustment of Lights vi. Control Panel Installation vii. Commissioning vii. Renting Crane for Erection

Supplying and stacking of good earth at site including royalty and carriage upto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S designation 16mm (20 % of Earth)

Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank.

Labour for laying, fitting and fixing NP2 R.C.C. spu pipe with colars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails, bonning rod, night guard, Red light and barrier etc. all complete as per specification and direction of E/I. 150mm dia RCC spun pipe - Upto 3.0 metre depth of invert below G.L.

250mm dia R.C.C. spun pipe

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not leaa than 36 kg) alongwith earth work in exacavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I. 200 mm Dia

250 mm Dia

Add 18% GST

Add 1% Labour cess 1%

SRI SATYA NARAYAN AGARWAL

ASHOK KUMAR PRADHAN