SPECIAL REPAIRS TO BUILDING NO P 8 AND P 9 AT INS HAMLA UNDER GE NW BHANDUP

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing rubbish off the premises complete all as specified and as directed .

Demolition of cement concrete in ground floor / paving not exceeding 15Cm thick below or above GL unreinforced complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed.

M&L PCC 20mm thick type B0, 1 : 2 : 4 (12.5mm graded aggregate) in sub flooring complete all as specified and directed.

M/L for 15 to 20mm machine cut kota stone slab in single piece with round nosing with three numbers of serration as in treads of steps for staircase laid over cement screed bed and jointed with grey cement slurry mixed with pigment to match the shade of of the slab including rubbing and mirror polishing over 15mm thick screed bed or bedding layer in CM1:4 complete all as specified and as directed.

M/L for 20-25 mm machine cut kota stone slab as in riser of steps, skirting, dado and pillar, cills and jambs laid over cement mortar backing coat jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with beewax polish over 10mm thick plaster in CM 1:4, complete all as specified and as directed

M&L machine cut kota stone slab flooring 20 - 25mm thick over 20mm cement screed in CM 1:6 laid and jointed with gray cement slurry mixed with pigment to match the shad of the slab including mirror polishing complete all as specified and as directed.

Cutting chases, pinning in brick wall, making good to facins where required and pointing in cement mortar 1 : 3 to ends of edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water tubing or concealed conduit wiring etc, making good, cutting exc 10cm girth but n exc 20cm girth complete all as specified and directed.

M&L Machine cut Kota stone slab (for CB shelf) 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing complete all as specified and directed.

M&L non-skid coloured joint free ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry over and including provision of bedding layer 15 mm thick in CM 1 : 4 complete all as specified and directed.

M&L glazed ceramic jointless coloured tiles in vertical surface 350 x 250 x 7mm / 450 x 350 x 7mm set and jointed in neat cement slurry over and including provision of bedding layer 10mm thick in CM 1 : 3 complete all as specified and directed.

M&L Marble work other than white or black 18 to 20 mm thick (table rubbed and polished) in cooking platforms, jambs and like over and including provision of 20mm thick cement mortar (1:4) including pointing in colour cement (1 :2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. .

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in (1:6) CM on fair faces of brick work or concrete surfaces of walls and finishing even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in (1:3) cm on fair faces of ceiling and finishing even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 20mm thick in two layers (15+5mm) in CM(1:4) with both layers mixed with liquid water proofing compound, surface finished even and fair without using extra cement (Note : WPC will be measured separately).

Supply only lilquid water proofing compound.

Labour only for complete removal of existing treatment on walls including washing / rubbing down with water including necessary scaffoldings etc complete all as specified .

M&L for applying 2 coats of white cement based wall care putty on wall, new or old surfaces of any description finished even and smooth complete all as specified and directed.

M&L for two coats of oil bound distemper on newly putty wall surfaces including necessary scaffoldings etc complete all as specified

Preparation of new surfaces of ceiling and application of three coats of white washing complete as specified and directed.

Preparation of old surfaces of ceiling and application of one coat of white washing complete as specified and directed.

M&L preparation of old surface of wall and applying one coat of white wash complete all as specified and directed.

M&L for preparation of New/old plastered surfaces on walls, chajjas, and applying two coats of 100% anti fungal weather resistant acrylic paint over a coat of acrylic primer in approved shade and as per manufacturer's instructions including necessary scaffolding complete all as specified and as directed.

Demolition of Reincorced concrete in roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified and directed.

M&L RCC M-30 (by using 20mm graded stone aggregate) for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

S&F Form work to soffits of suspended slabs such as roof slabs, floor slabs landings and similar work not exceeding 200mm thick( horizontal or sloping) complete all as specified and directed.

M&L form work to edge of concrete RCC slab or RCC band exc 10cm wide but n exc 20 cm wide and fair finished surface complete all as specified and directed.

S&F TMT bars 10mm dia & over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

S&F TMT bars 6 to 8mm dia, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for providing stages wise waterproofing treatment to sunken portion of toilets as under. Stage 1: Demolition of WC including lime concrete and cement concrete coba etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debries outside MD land etc complete all as specified and directed. Stage 2: Providing 15 mm thick plaster in CM 1:3 mixed with integral water proofing chemical of STP Ltd in the proportion /quantity all as per manufactures instructions. Stage 3 : Primer - Mix Tarfelt LM with water in ratio 1:1 @ 250 gms/sqm and apply the primer on the plaster surfaces. Stage 4 : Application of 1st coat of Tarfelt LM of STP Ltd without dilution with water@1kg/sqm by brush all as per manufactures instructions. Stage 5: Laying 50 GSM fyber glass cloth over the 1st coat while the coated surface is still tacky. Stage 6: After 6 to 7 hours interval apply second coat i.e final coat of Tarfelt LM without dilution with water of STP Ltd by brush as per manufactures instructions.@1kg /Sqm Stage 7: Providing 10mm thick protective plaster in CM 1:3 mixed with STP NO -1 @ 250ml/50kg cement all as manufactures instructions. And also provive GI spout for sunken area.

M&L for cement concrete Type E2 1:5:10 using 40 mm graded aggregate or brick bats as in lean concrete complete all as specified and directed.

S&F vitreous China squatting pan, 'orrisa' pattern wc of size 580 x 440 mm white with integral foot rest (excluding flushing cistern and flush pipe but including 'P' or 'S' trap and provision of lime concrete bedding in repairs complete all as specified and directed. Note:- Flushing cistern and flush pipe will be measured and paid under supply only rate.

M&L WC connector 110 mm PVC SWR for WC complete all as specified and directed.

Supply only PVC connector 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

M&L PVC valveless, syphonic action type, 10 ltrs cap flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and flush pipe 32mm dia and fixed in repairs complete all as specified and directed.

S & F cast iron Nahani trap in floors with grating including jointing to waste pipe of 75mm dia in cement concrete type B1 (1:2:4) fixed in repairs complete all as specified and directed.

S&F 40mm bore high density polythene pipes (HDPE) of pressure rating 6 Kg / cm2 fixed complete to walls, ceiling or in floors etc complete all as specified and directed.

S&F in repairs stainless steel sink with drainage board made of stainless steel 1mm thick kitchen or labouratory with plugs, washers, and wastes. including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm X 460mm and bowl size 410mm x 330mm x 160mm including necessary fittings such 40mm coupling waste, pipe complete all as specified and directed. Make : Nirali, Bule star ISI marked.

M&L Wash hand basin, Vitreous China white (Flat back) 630 x 450mm including brackets,, pinning in ends of brackets or erecting stand including fixing of waste pipe and pillar tap etc ( Suppy of pillar tap and waste pipe shall be measured separately) complete all as specified and directed.

Supply only pillar tap cast copper alloy chromium plated fancy type complete all as specified and directed.

M&L stop valves 15mm bore dia, cast copper alloy fancy type, chromium plated with long shank and cup concealed type, screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions in repairs complete all as specified and directed.

M&L Low density polyethlene (LDPE) pipe of pressure rating 6 Kgf / Sqcm 32mm dia complete all as specified and directed.

M&L Low density polyethlene (LDPE) pipe of pressure rating 6 Kgf / Sqcm 40 mm dia complete all as specified and directed.

M&L bib tap brass 15mm bore dia chromium plated fancy type with curtch or butterfly handle , screwed down, screwed for iron pipes complete in repairs complete all as specified and directed.

S&F in repairs brass chromium plated towel rail 20mm dia, "D" type, 600mm long between flanges complete all as specified and directed.

S&F stainless steel soap dishes approximate size 160mm x 160mm x90mm as complete as specified as directed by GE.

M&L Glass Assembly sheet glass consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracked guard and railing 60cm long in repairs complete all as specified and directed.

M&L Hat and coat hooks, solid body of aluminium, 175mm to 250mm long and fixed in repairs complete all as specified and directed.

M&L Brass chromium plated shower rose 125mm size including fixing to steel pipe or union in repairs complete all as specified and directed.

Taking up or down steel tubing 15mm bore of pipe and connections including cleaning for refixing etc as required complete all as specified and directed.

All as per item No 52. but 20mm bore of pipe complete all as specified and directed.

All as per item No 52 but 25mm bore of pipe complete all as specified and directed.

M&L tubes medium grade galvanised, with all fittings and fixed complete to walls or ceiling or laid in floors 15mm bore dia complete all as specified and directed.

All as per item No 55 but 20mm bore dia complete all as specified and directed.

All as per item No 55 but 25mm bore dia complete all as specified and directed.

S&F gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed bore of 25 mm in repairs complete all as specified and directed.

M&L Rotational moulded polyethylene water storage tanks (Cylindrical verticval with closed top) hoisted & fixed in position in repairs all as specified of 2000 ltrs capacity complete all as specified and directed.

M&L in repairs Ball valve high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete .25mm dia complete all as specified and directed.

M&L Nipple suitable for HDPE water tank (minimum weight 25mm - 65 gms) 25mm bore dia complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutter from the frames) exceeding 1.5 sqm but n exc 4 sqm completed as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutter from the frames not exceeding 1.5 Sq. M each complete all as specified and directed.

Taking down shutter of any description exc 1.00 but n exc 2.00 sqm each Sqm each complete all as specified and directed.

S&F extruded Powder coated aluminium section as in window, ventilation,door (powder coated 50 micron in blackcolour) with movable, openable or fixed type shutter or any pattern as directed, aluminumsection medium weight of series B or size as directed by the Engr in charge cut to size , jointed toghter including rubber beading and all necessary fitting complete all as specfied and directed (Make: Jindal/Hindalco) Note :- (i) Only aluminum sections measured and paid in this item. (ii) Rate quoted by the contractor shall deemed to be inclusive of all neecssary fittings and fixture such as roller,handle,locks etc (iii) Glass pane and XPM jali measured and paid under supply only rate.

S & F aluminium grill conforming to DG- 102 of Deco Grill or equivalent , (10mm X 5.2mm) thick of approved design or equivalent as approved by Accepting Officer and fixing with and including 'F/U' channel not less than 1.5mm thick complete all as specified and directed.

Supply only sheet glass 5.00 mm thick in glazing with rubber and aluminium beading/ packing with rubber gasket complete as specified and directed.

Supply only aluminium anodised XPM Jali, 0.45mm nominal dia with 1.4mm average width of aperature complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F IInd class Hard Wood plain, solid straight chawkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, completed as specified and directed.

S&F MS flot iron as in hold fast and similar work as specified Gde Fe 290 or E-165 complete all as specified and directed.

M&L PCC Block for hold fast and similar work etc 1 : 2 : 4 type B-1(using 20mm graded stone aggregate) complete all as specified and directed.

M&L preparing surfaces of wood or wood based materials, any description ends of posts, backs of chowkats, etc and treating with tar or coal tar black paint area tarred exc 0.1 sqm but n exc 0.5 sqm each complete all as specified and directed.

Preparing surfaces of small articles such as stop, covers, gully gratings, holdfasts, ends of posts, backs of chowkats etc area n exsc 0.1 sqm each and treating with tar or coal tar black paint complete all as specified and directed.

M&L Flush shutters 30mm, solid core construction, with partical board core and ply wood face panels, commercial type on both sides complete all as specified and directed.

S&F 35mm IInd class hard wood glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc (without sash bars) edge of framing plain, chamfered or rounded, fitted with cut and mitred bends for securing glass etc. size of members of shutters as specified in SSR, Part I, section -8, clause 8.20(a) supplied and fixed to chowkhats complete all as specified and directed.

Supply & Fixing aluminium anodised XPM Jali, 24 gauge with 1.4mm average width of aperature complete all as specified and directed.

M&L prelaminated particle board 18/19mm thick, interior grade, prelaminated one side with decorative choice lamination & other side balancig white lamination, fixed with screws in repairs for pelmet boxes complete all as specified and directed.

S&F Hasp and staple 150mm size, safety type of aluminium with aluminium pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S&F continuous (piano) hinges mild steel, bright finish or electrogalvanised 40mm width of flaps complete all as specified and directed.

S&F stainless steel butt hinges 100mm size complete all as specified and directed.

S/F 150mm length extruded aluminium alloy handles,fabricated type, anodised complete all as specified and directed.

S&F200 mm length aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F Aluminium anodised barrel tower bolt of extruded section and fixed 300mm long complete all as specified and directed.

M&L 300mm long Aluminium alloy, anodised, sliding door bolt with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section or cast aluminium alloy and fixed complete all as specified and directed.

M&L 150mm long Aluminium alloy body latch, anodised with two levers and fixed complete all as specified and directed.

S&F 150mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and directed.

M&L 300mm, ordinary rat tail rod pattern springs including roller and roller plate mild steel complete and fixed in repairs complete all as specified and directed.

M&L for preparation of new wood and wood based surfaes any description, not otherwise described oer 10cm width or girth one coat of pink primer and application of two coats of synthetic enamel paint on new wooden surfaces complete all as specified and directed.

M&L for preparation of old decorated wooden surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint. complete all as specified and directed.

S&F curtain rod 20mm dia Aluminium anodised & fixed in repairs complete all as specified and directed.

S&F in repairs Aluminium brackets for curtain rail 20mm dia and fixed complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fitting and accessories)

S&F 75mm bore PVC soil waste pipe pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc including taking down of any type complete all as specifed and directed.

S&F 110mm bore PVC soil waste pipe pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc including taking down of any type complete all as specifed and directed.

S&F 200mm bore PVC rain water pipe single socketed(ISI Marked) any length with rubber ring joints , complete fittings etc fixed to wall fixed with MS clamps8mm dia with two nuts wall nails etc including taking down of any type complete all as specifed and directed.

S&F 200mm dia PVC (SWR) single PVC (SWR) bend any radius, completed as specified and directed.

S & F 110 mm bore PVC (SWR) Branch piece, single (single Y) equal or unequal of any radius with access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) Branch piece, single (single Y) equal or unequal of any radius with access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) branch piece (Double `Y') equal or unequal with access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) branch piece (Double `Y') equal or unequal with access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bend any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) Vent Cowl complete all as specified and directed.

S & F 75 mm bore PVC (SWR) Vent Cowl complete all as specified and directed.

S& F Stack clamp out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 200mm bore dia complete all as specified.

S& F Stack clamp out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110mm bore dia complete all as specified.

S& F Stack clamp out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 75mm bore dia complete all as specified.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L brushing neat cement slurry @ 3 Kgs of cement per Sqm complete all as specified and directed.

M&L for PCC (1:2:4) type B0 using 12.5 mm graded stone aggregate as in levelling padding course over RCC roof surface including rounded or chamferred on edges etc., with approved water proofing compound all as per manufacturer's instructuions on the roof surface to achieve requisite slope all as specified and directed. (Note :- Supply only water proofing compound shall be measured & paid separately).

Rendering 15mm thick in (1:3) CM on fair faces of brick work or concrete surfaces and finishing even and smooth without using extra cement complete all as specified and directed.

M&L for providing 4 mm thick APP modified membrane over (Accessible) RCC roof with the following specifiations :- (a) Cleaning existing surface properly. (b) Apply oil bound bitumen primer @ 0.40 lit/Sqm manufactured by the same agency as that of APP with a density of 0.87 -0.89 Kg/Lit at 25 Degree Centigrade on the prepared dry roof surface. (c) Providing and Laying APP modified water proofing membrane reinforced with non wooven polyster mat with physical properties as under :- (i) Membrane weight >3.6 Kg/Sqm . (ii) Net woven polyster weight >160 gm/Sqm (iii) Softening point of membrane > 150o C (iv) Joint Tensile strength Longitudiual > 650 Sq Cm at 230o C & Transverse > 450/ Sqcm (v) Tear strength - Longitudual > 300 N & Transverse > 250 N Direction (vi) Elongation > 30 % (vii) Impermeability under water pressure > 3 Kg/Sq cm Note :- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane. (d) Over the membrane provide 20-25 mm thick machine pressed cement concrete tiles 300mm x300mm over & incl cement screed bed 15mm thick in CM 1:4 set and jointed, pointed in neat cement slurry with grey cement complete all as specified and directed".

M&L for providing 4 mm thick APP modified memberane in repairs including removing old treatment over (Inaccessible) RCC roof with the following specifiations :- (a) Cleaning existing surface properly. (b) Apply oil bound bitumen primer @ 0.40 lit/Sqm manufactured by the same agency as that of APP with a density of 0.87 -0.89 Kg/Lit at 25 Degree Centigrade on the prepared dry roof surface. (c) Providing and Laying APP modified water proofing membrane reinforced with non wooven polyster matt with physical propertities as under :- (i) Membrane weight >3.6 Kg/Sqm. (ii) Net wooven polyster weight >160 gm/Sqm (iii) Softening point of membrane > 150o C (iv) Joint Tensile strength Longitudiual > 650 Sq Cm at 230o C & Transverse > 450/Sqcm (v) Tear strength - Longitudual > 300 N & Transverse > 250 N Direction (vi) Elongation > 30 % (vii) Impermeability under water pressure > 3 Kg/Sqcm Note:- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane. (d) Over the membrance provide a finishing with solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane complete all as specified and directed.

Chipping, removing, carefully concrete including loose palster by low impact Hammer without damaging the structure and cleaning and disposal of debris out side the premises including necessary form work ie providing & erecting steel props, safety nets, dust control net, Self supported two legged B class tubular steel scaffolding , 4mm thick ply covering to machineries / other utilities etc complete all as specified and directed.

Cleaning the existing reinforcement with wire / rotary wire brush, making the surfaces free from loose material dirt etc, complete. Applying two coats of alkaline rust converting primer conforming to ASTM-B- 117, on the rebars, including cleaning the reinforcement, wire brushing to remove loose rust spalls, with time interval of 1 hour between the coats complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. Note: (1) Anchoring of reinforcement bars will be measured and paid seperately under item No 119. (2) This item is applicable for additional bars requied in the existing RCC structures.

M&L for anchoring & welding reinforcement bar in existing RCC member by providing holes of minimum 10d depth for bars upto 16 mm dia and grouting in position with locfix (fosroc), including drilling of holes, cleaning etc. complete all as specified and directed, Note:-reinforcement will be measured and paid for separately.

M&L for carrying out application of 'Bi-polar migratory corrosion inhibitor' EPCO-KP-100 on concrete surface. This inhibitor has migratory kind of propertyh which permits the material to migrate to a virtual extent of 100mm, through pores of concrete, inhibiting the corrosion and de-passivating the Electro-chemical reaction. It has property to attach anode as well as cathode, which is purely alkaline in nature (pH-9.5), so it has no carcinogen activity with concrete complete all as specified and directed.

M&L for applying Anticorrosive Treatment to Reinforcement by IPNET RB. Application of two coats of IPNET RB on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be by brush complete all as specified and directed.

Providing and applying structural grade epoxy-latex bond coat pririor to application of any type of mortar conforming to ASTM-C-882-91 (Arizona Slant Shear Test) to ensure bond between old concrete & new concrete by brush application complete all as specified.

Providing, casting & repairing of excessively damaged members with Micro-concrete at all levels with all leads & lift or as directed including formwotk, centering, scaffolding & mixing, laying, levelling and finishing including curing etc complete ( for thickness more than 40mm) all as specified and directed.

Building up the profile of structual members by using polymer modified mortar upto 20mm thickness including levelling profilling etc complete all as specified and directed.Make:- Molith PMM of Krishna conchem or equivalent.Note :- Mode of measurement : Superficial area of concrete will be measured.

Building up the profile of structual members by using polymer modified mortar upto 40mm thickness including levelling profilling etc complete all as specified and directed.Make:- Molith PMM of Krishna conchem or equivalent.Note :- Mode of measurement : Superficial area of concrete will be measured.

Removing and cleaning existing vegetation growth in Structural & Non Structural members, shall be done by uprooting the tree projections of any girth, depth etc from members, cleaning roots and other plant extracts from the members, filling the voids in structural elements shall be done by cleaning the voids, cutting with concrete cutter to retular shape, applying polymer modified mortar 1 :4 propostion with addition of specified polymer 20% by weight of cement, finishing with spatula to build up section of the member complete all as specified.

Flush cutting of RCC chajjas, fins with reinforcement up to 150 mm depth by norms of RCC mechanical cutting machine, all as specified.

S&F premoulded FRP Chajjas with 2 to 2.5 mm FRP thickness on both sides with manglore clay type finished with 150 mm drop on front, sides and 60 mm collar on back side including necessary fixtures complete all as directed.

M&L for post construction anti- termite traetment along the external wall below concreate or masonary apron using chemical emulsion @2.25 liters per linear meter including drilling and plugging holes with cement morter 1:2 to match the existng floor etc complete all as specified and directed.

M&L for post construction anti- termite of soil / concreate under existing floor along the floor and wall junction using chemical emulsion @ 1 liters per hole 300 mm apart including drilling and plugging 12 mm dia holes with cement morter 1:2 to match the existing floor etc complete all as specified and directed.

M & L for post construction anti - termit treatment at points of contract of wood work using chemical emulision (in oil or kerosin based solution ) @ 0.5 liters per holy by drilling 6 mm dia holes at a down ward angles of 45 degree at 150 mm centere to center and sealing the same with white cement and making good to the existing surfaces etc complete all as specified and directed.

Demoltion of brick work or stone/boulder masonry, built in cement mortar or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facing, precast concrete articles complete all as specified and directed.

M&L for brick work with Sub class 'B' bricks straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L Pcc (1:2:4) type B1 (20mm graded aggrgate) as in coping, lintel bands , hold fast, PCC benching weathering etc.including necessary form work complete as specified and directed.

M&L for 50mm thick Pcc (1:3:6), type C1, using 20mm graded stone aggregate as in plinth protection / paving, surfae finished even & smooth without using extra cement complete as specified and directed.

Forming construction Joint 30mm deep x 10mm wide filled with sealing compound grade 'A' complete all as specified and directed.

M&L for Brick work with sub class-"B" Bricks, straight or curved on plan exc 6m mean radius built in CM (1:4) Complete all as specified and directed.

Material and Labour for rendering 15 mm thick cement plaster in CM (1:4) on fair faces of brick work or concrete surfaces and finished with 5 mm thick plaster, complete all as specified & directed.

Exavating in trenches in Hard / dense soil n. exe 1.5 m wide and n. exe 1.5 m in depth, for foundation etc or for shafts, wells, cess pits, man holes, pier holes etc n exe 10 sq m on plan n exe 1.5 m depth and getting out complete all as specified and directed

S/F 150mm bore salt glazed stone ware drain pipes laid in trenches and jointed as specfied complete all as specfied and directed.

M&L for concrete in cement concrete 1:3:6 type C2 to bed drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specfied and directed.

Returning, filling in, including spreading, levelling, watering and well raming in layer not exe 25cm complete as specified and directed.

Removing exavated material ourside MD land exe 1.50km but n. exe 5km and depositing where directed complete as specified and directed.

Cutting into existing man holes for connecting new drains of 150mm dia pipe and making good two pipes and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 and finished and reforming benching as required complete all as specified and directed.

Demolition of Reincorced concrete in any position, manhole covers etc & disposal of subbish off the premises complete all as specified and directed.

M&L precast RCC 1 : 1.5 : 3 type A1 (using 20mm graded stone aggregate) in cover slab and set in CM 1 : 4 including necessary form work complete all as specified and directed.

M&L in repairs PVC(SWR) gully trap 125 / 110mm setting and jointing with solvent cement complete all as specified.

S & F in repairs stainless steel plated rack of overall size 75 x 75 Cm made out of 0.8mm thick SS sheet, with shelves and racks to hold kitchen utensils such as plated, tumblers, bowls and cutlery etc with edges of racks and shelves turned in, including fixing to wall iwth brass chromium plated screws as directed, plate rack of design and quality as approved and directed.

Taking down carefully copper/alumunium point wiring for light, fan, bell, socket or power complete including fittings such as switches, ceiling roses pendents regulators, sockets and tube light fittings etc, removing materials from site or for reuse refixing and making good distrubed surface of wall, floors etc all as specified and directed.

Taking down main switches DBs with sheet metal enclosure 2/4/6/8/12 way SPN/TPN/DBs etc all as specified and directed.

Taking down down ceiling fan/exhaust fan from the position and deposit MES store yard all as specified and directed

M&L for light/fan point wiring complete with 1.5 sqmm PVC insulated unsheathed 1100 volts grade (FRLS) cable stranded copper conductor single core partly concealed in wall through PVC conduit and concealed accessories and partly surface on ceiling, beams and cloumns through casing capimh and accessories of size 20/25mm complete with modular box and plate for fitting mounting switch/sockets regulators with 1.5 sqmm PVC insulated copper conductor earth wire and connected to earth dolly for one light point controlled by one switch complete

All as per item No 152 herein above but ceiling/Exhaust fan point controlled by one switch complete all as specified and directed.

All as per item No 152 above but for one bell point controlled by 5 Amps bell Push complete all as specified and directed.

All as per item No 152 herein above but for one 3 pin switch socket 5 Amp same board complete all as specified and directed.

All as per item No 152 herein above but for one 3 pin switch socket 5 Amp independent complete all as specified and directed.

M & L for point wiring complete with proper colour coding using 1100 volts grade, 2.5 Sqmm, PVC insulated, FRLS,unsheathed wire with multi stranded copper conductor confirming to IS-694, Part II, ISI marked, drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good the same in CM 1:3 to match with the existing surfaces and partly drawn in and including PVC casing caping fixed on the surfaces of RCC slab/ ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc, including provision of modular metal flush boxed with modular cover plate and frame suitable for mounting modular switches , sockets, fan regulators etc, also inclduifng 2.5 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts mutli-stranded copper conductor green colour as continous earth wire connected to common earth dolly all as specified and diretced for one 5Pin,6/16Amps,Socket outlet independent,complete all as specified and directed

Supply & fixing ceiling rose , surface bakelite 3 terminal complete all as specified and directed.

Supply & fixing switch modular type 6 Amp single pole one way 230V complete all as specified and directed.

Supply & fixing socket modular type 6 Amp 2/3 pin single pole one way 230 V complete all as specified and directed.

Supply & fixing switch modular type 16 Amp single pole one way 230V complete all as specified and directed.

Supply & fixing socket modular type 16 Amp 2/3 pin single pole one way 230 V complete all as specified and directed.

Supply & fixing Modular white cover plate with frame 6 Module complete all as specified and directed.

Supply & fixing Modular white cover plate with frame 3 Module complete all as specified and directed.

Supply & fixing modular Metal Flush box 6/8 Module complete all as specified and directed.

Supply & fixing modular Metal Flush box 3 Module complete all as specified and directed.

Supply and fix in replacement of bell push 6 Amp modular type single pole 230 volts one way complete all as specified and directed.

Supply and fix in replacement of call bell AC, 230 Volts single pole all as specified and directed.

M&L for sub main wiring complete two run of size 4.0 sqmm PVC insulated ,unsheathed, heavy duty 1100 volts grade (FRLS) multi-stranded copper conductor cable,drawn partly in and including PVC conduit concealed in walls etc including cutting chases and making good in CM 1:3 to match with the existing surfaces and partly drawn in and including PVC casing caping fixed on the surfaces of RCC slab/ceiling/columns/beams etc with all accessories, fittings, PVC junction boxes etc, also including one run of 4.0 Sqmm, PVC insulated, FRLS, unsheathed, 1100 Volts multi-stranded copper conductor green colour as continous earth wire connected to common earth dolly and mains, complete all as specified and directed.

S&F ceiling fan 1200 mm sweep with electroninc fan regulator modular type , 230 Volt, BEE 5 star rating and provisioning of flexible copper cord of size 23/0.0076 of required length from ceiling rose or connector to ceiling fan, complete with dow rod, blades, canopies etc, all as specified and directed.

Supply & fix exhaust fan 300 mm sweep, 900 rpm, 230V complete with louvers, steel body, bolts, nuts, washers, suitably embedded in wall with provisioning of 23/0.0076 flexible three core wire for electrical connections from ceiling rose to fan and cutting of wall suitable size for fixing of exhaust fan all as specified and directed.

Supply and fixing integrated sleek extruded LED channel with acrylic cover 20 watt with white light including with driver and preqired complete including 0.5 sqmm 3 core flexible wire connecting from ceiling rose complete all as specified and difected. Make :Luker Cat No. LT5M20,

Supply and fixing integrated sleek extruded LED channel with acrylic cover 10 watt with white light including with driver and preqired complete including 0.5 sqmm 3 core flexible wire connecting from ceiling rose complete all as specified and difected. Make :Luker Cat No. LT5M10,

Supply and fix in repairs highly efficient high power 25 W LED street light fitting with pressure die cast aluminum housing heat resistant toughened glass in bulit fittings etc, with all accesories, pre-wired, also with and including GI steel tube lihht grade 40mm bore bracket of length upto 1.50 metre, bent to shaoe of off set angle upto 45 dgree for fixing street light fittings including necessary MS clamps, nutsm bolts etc all as specified and directed. make havels Cat No ENDURAPEARLSL25WLED757SASYTOPC, IP-66 protection or equivalent from Philips/bajaj/Crompton, as approved by the GE

Supply and fix sheet metal enclosure powder coated for MCB DB SPN 12 way double door type with din rail and bus bar including making good to the disturbed surface matching with the existing complete all as specified and directed.

Supply and fix sheet metal enclosure powder coated for MCB DB SPN 8 way double door type with din rail and bus bar including making good to the disturbed surface matching with the existing complete all as specified and directed.

Supply and fix of MCB SPN 240 Volts 32 Amp breaking capacity 10 KA rating complete all as specified.

Supply and fix of MCB SP 240 Volts 6 to 32 Amps breaking capacity 10 KA rating complete all as specified and directed.

Material and labour for earthing complete with GI earth plate electrode 600x600x6 mm thick burried directly in ground (earth pit not less than 2.25 mtr deep below ground lavel) with top edge of the plate not less than 1.5mtr below normal ground lavel connected to GI earth strip 32X6 mm by mean of bolts, nuts, check nuts and washer of brash all as shown in electrical plate No 5 connected to earthing test point all as specified or indicated including PCC pit and CI cover fullel with watering pipe, wire mess and copper lugs etc GI protection pipe 40 mm dia medium grade including testing on completion all as specified and directed.

R K TYAGIS

kajal construction

M/s. MAYUR ENTERPRISES