Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹1.3 CrAccepted-AOC LEIMAKHONG BAZAR P O MANTRIPUKHRI DIST KANGPOKPI MANIPUR 795002 | KANGPOKPI | MANIPUR | 795002 | ₹1.3 Cr | L1 | Accepted-AOC Reasonable rate. |
| 2 | L2₹1.4 Cr+₹12.1 L (9.21%)Rejected-Finance FLAT NO B 205 S NO 296 2 DIVINE HOMES PORWAL ROAD LOHEGAON PUNE 411047 | PUNE | MAHARASHTRA | 411047 | ₹1.4 Cr+₹12.1 L (9.21%) | L2 | Rejected-Finance Quoted amount higher than L1 |
| 3 | L3₹1.5 Cr+₹21.4 L (16.3%)Rejected-Finance | ₹1.5 Cr+₹21.4 L (16.3%) | L3 | Rejected-Finance Quoted amount higher than L1 |
| Sl No | Description | Qty | Unit | M/S YAIPHABA ENTERPRISES L1 | BSK Construction L2 | M/S Apple constructions L3 |
|---|---|---|---|---|---|---|
| 1.00 | M & L for Construction of Valve Chamber of size 1200 X 1200 X 900 mm internal size suitable for Sluice Valve, with PCC 1:4:8, Type D2, using 40mm graded aggregate for foundation, 200 mm thick Brickwork with Fly Ash Bricks in Cement Mortar 1:6, 40 mm thick PCC, 1:2:4, Type B1, using 20mm graded aggregate Coping, rendering in CM 1:4, 15 mm thick including provision of Mild Steel Sheet Cover 3 mm thick with 40 X 40 X 6 mm size Angle Iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and including necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises, demolition of existing Valve Chamber of any description complete all as specified and shown on drawing No. TD/EM/06, Sheet No. 1 / 2, 2/2 and as directed by the Engineer-in-Charge. | 4 | Each Job | 35,500 ₹1,42,000 | 35,000 ₹1,40,000 | 34,200 ₹1,36,800 Lowest |
| 2.00 | Design, fabrication and supply and installation of 6600 gallon (30000 ltr) capacity made with 5 mm thick MS Steel water storage tank of size 6.25 Mtr. X 3.75 Mtr. x 1.25 Mtr internal size with all accessories including roof covers, nuts, bolts, washer, bracing angle, jointing materials etc complete all as specified and directed. Different size of sections and length shall be are as under:-
Notes : (i) Nos of 5 mm thick MS plate of Size 1250 mm x 1250 mm = 31 nos
(ii) Corner angle angle iron of 65 mm x 65 mm x 6 mm thick x 1240 mm = 20 Nos
(iii) Bracing angle angle iron of 75 mm x 75 mm x 6 mm thick x 1580 mm = 12 Nos
(iv) Rafter angle angle iron of 75 mm x 75 mm x 6 mm thick x 3670 mm = 4 Nos
(v) Roof cover 1350 mm x 2600 mm x 3.15 mm thick = 03 nos
(vi) Roof cover 1310 mm x 2600 mm x 3.15 mm thick = 03 nos
(vii) Roof cover 1350 mm x 2560 mm x 3.15 mm thick = 01 nos
(viii) Roof cover 1350 mm x 1350 mm x 3.15 mm thick = 01 nos | 4 | Each Job | 14,54,000 ₹58,16,000 Lowest | 20,00,000 ₹80,00,000 | 16,75,000 ₹67,00,000 |
| 2.01(ix) All joint filled with lead wool and putty (x) Tank should be painted internally with two coats of black bitumenous paint over a coat of primer and two caost of aluminium paint over a coat of red oxide primer externally. (xi) Water level indicator and ladder of required height should be provided at no extra cost. (xii) Inlet, outlet and wash out provision should be provided. (xiii) corner Box/Joint box= 8/20 Nos Note:- (i) Foundation should be measured and paid separately under relevent item of BOQ. (ii) The design and fabrication of tank shall be done in accordance with IS-804: 1967 and shall be vetted by structural Engineer of NIT/IIT/Govt Engg College and then finally approved by the GE and cost the same shall have deemed to included with unit quoted rate. (iii) If any variation of section size and length on heigher side no price adjustment shall be entertained but if the smaller size and length shall be used, minus adjustment shall be done. (iv) Water potabality test shall be carried out at NABL/ state govt lab. | ||||||
| 3.00 | Supply, install, fixing, commissioning and testing of TEFC mounted centrifugal type split casing pump set with CI casing, bronze impellers, C-45 shaft with pumping capacity 3500 LPM at 50 to 80 mtr head, coupler with and including energy efficieny-2 induction motor of suitable capacity and conforming to IS : 12615 , 415Volt, 3 phase, 1450 rpm to 2000 rpm-50 Hz, AC supply and suitable for drinking water including suitable size factory mild steel base frame fixed in and including foundation as per manufacturer's recommendation with nuts and bolts including anti vibration pads, painting and connection with suction & discharge water main complete with 150 mm dia foot valve at suction end, 150 mm dia NRV of size at delivery end with standard fittings and necessary electric connections with PVC insulated industrial heavy duty copper cable 16Sqmm, 3 core, 1100 volt from starter to pump set complete all as specified and as directed.Notes :- (i) Necessary foundation, base frame & bolting required for installation high pump set shall be provided as per manufacturer's recommendation and shall be measured and the cost for the same shall be deemed to be included in the rates quoted for this item.
(ii) The cost of PVC insulated industrial heavy duty cable and all other standard accessories shall be deemed to be included in the rates quoted for this item.
(iii) Foot valve and NRV should be measured and paid separately under relevent item of BOQ. | 2 | Each Job | 9,98,000 ₹19,96,000 | 8,50,000 ₹17,00,000 Lowest | 13,20,000 ₹26,40,000 |
| 4.00 | Supplying, installation, testing and Commissioning of open well submersible pump set of 20 HP, 400 to 4800 LPM capacity, IP 68 protection, CI casing with CI motor body, CI impeller, operates at 440 volts, 3 phase 50 Hz suitable for 150mm dia delivery pipe complete all as specified and as per manufacturer's instructions and as directed by Engineer-in-Charge. | 4 | Each Job | 4,88,000 ₹19,52,000 | 2,75,000 ₹11,00,000 | 56,400 ₹2,25,600 Lowest |
| 5.00 | Supplying, installation, testing and Commissioning of automatic bleaching stick dosing system, capacty 100 litres , max temp- 45 degree celcius, made with non-mettalic thermoplastic, operates on 230 volts, 50 Hz including required attachments such as station holding assembly, water inlet regulator, over flow vent, drain valve, fluid level controller with inbuilt level switch, sludge level guage, station base assembly with station base bufferm station hood assembly with multy cavity arrangement along with minimum 125 sticks complete all as specified and as per manufacturer's instructions and as directed by Engineer-in-Charge. | 1 | Each Job | 4,62,000 ₹4,62,000 | 1,10,000 ₹1,10,000 Lowest | 6,10,000 ₹6,10,000 |
| 6.00 | Supply, installation, testing and commissioning of automatic delta starter for 50 HP, 37KW, 415 volt, 50Hz conforming to IS/IEC60947-4-1, IP-54 protection, extended with band coil, internal wiring with FRLS copper wiring of suitable size, air break type starter, class H insulation complete all as specified and as directed. | 2 | Each Job | 48,800 ₹97,600 Lowest | 1,75,000 ₹3,50,000 | 67,500 ₹1,35,000 |
| 7.00 | Supply, installation, testing and commissioning of automatic delta starter for 20 HP, 16KW, 415 volt, 50Hz conforming to IS/IEC60947-4-1, IP-54 protection, extended with band coil, internal wiring with FRLS copper wiring of suitable size, air break type starter, class H insulation complete all as specified and as directed. | 4 | Each Job | 22,000 ₹88,000 Lowest | 85,000 ₹3,40,000 | 34,200 ₹1,36,800 |
| 8.00 | Supply and laying of 16 Sqmm 3 core submersible flat cable complete all as specified and as directed. | 416 | RM | 1,130 ₹4,70,080 | 750 ₹3,12,000 Lowest | 2,090 ₹8,69,440 |
| 9.00 | Supply and laying of PVC hose pipe of 150mm dia including all required fitting such as clamp / screws of suitable size to fix the pipe with pump set complete all as specified and as directed. | 121 | RM | 1,350 ₹1,63,350 Lowest | 2,000 ₹2,42,000 | 3,210 ₹3,88,410 |
Tender Value
₹1.3 Cr
EMD Value
₹2.1 L
Closing Date
23 Apr 2026, 6:00 pmClosed
COL AMIT CHAUBEY
HQ 137 Wks Engr PIN 914137 c/o 99 APO
SPECIAL REPAIRS TO BER PUMPS AND MS WATER TANK OF 6400 GALLON CAPACITY INCLUDING ALL CONNECTED ITEMS AT LEIMAKHONG MIL STN
2026_MES_757820_1
8100/E8
Open Tender
Civil Works
Item Rate
180 days
LEIMAKHONG
As per tender document
6 documents required · 6 mandatory
₹1,000
GE 869 EWS
₹2.1 L
Yes
9 Jun 2026
26 Mar 2026
30 Apr 2026
26 Mar 2026
23 Apr 2026
16 Apr 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| - | M & L for Construction of Valve Chamber of size 1200 X 1200 X 900 mm internal size suitable for Sluice Valve, with PCC 1:4:8, Type D2, using 40mm graded aggregate for foundation, 200 mm thick Brickwork with Fly Ash Bricks in Cement Mortar 1:6, 40 mm thick PCC, 1:2:4, Type B1, using 20mm graded aggregate Coping, rendering in CM 1:4, 15 mm thick including provision of Mild Steel Sheet Cover 3 mm thick with 40 X 40 X 6 mm size Angle Iron frame work embedded in concrete with suitable hinges and locking arrangements including two coat of synthetic enamel black paint over a coat of red oxide zinc chrome primer to steel surfaces and including necessary earth work excavation in any type of soil etc., removal of surplus soil off the premises, demolition of existing Valve Chamber of any description complete all as specified and shown on drawing No. TD/EM/06, Sheet No. 1 / 2, 2/2 and as directed by the Engineer-in-Charge. | - | Each Job | - | - |
| - | Design, fabrication and supply and installation of 6600 gallon (30000 ltr) capacity made with 5 mm thick MS Steel water storage tank of size 6.25 Mtr. X 3.75 Mtr. x 1.25 Mtr internal size with all accessories including roof covers, nuts, bolts, washer, bracing angle, jointing materials etc complete all as specified and directed. Different size of sections and length shall be are as under:-
Notes : (i) Nos of 5 mm thick MS plate of Size 1250 mm x 1250 mm = 31 nos
(ii) Corner angle angle iron of 65 mm x 65 mm x 6 mm thick x 1240 mm = 20 Nos
(iii) Bracing angle angle iron of 75 mm x 75 mm x 6 mm thick x 1580 mm = 12 Nos
(iv) Rafter angle angle iron of 75 mm x 75 mm x 6 mm thick x 3670 mm = 4 Nos
(v) Roof cover 1350 mm x 2600 mm x 3.15 mm thick = 03 nos
(vi) Roof cover 1310 mm x 2600 mm x 3.15 mm thick = 03 nos
(vii) Roof cover 1350 mm x 2560 mm x 3.15 mm thick = 01 nos
(viii) Roof cover 1350 mm x 1350 mm x 3.15 mm thick = 01 nos | - | Each Job | - | - |
stage.html
html • 0.05 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.31 MB
BOQ_848850.xls
BOQ • 0.25 MB
8100tenderdocx.pdf
Tender Documents • 1.62 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .