CWE/P-64/2019-20 SPECIAL REPAIR TO ORS MD ACCN BLDG NO NP-10 AND

Amount

M & L Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M & L Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc complete all as specified and as directed.

M&L for Non - skid ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for glazed ceramic coloured tiles in vertical surface 450x350x7mm thick, set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M & L 20 mm thick granite ( black) work (table rubbed and polished) cills, cooking platforms, in steps, jambs, pillars, window-cill and like in cement mortar (1:4) 10mm thick including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed. Note : All Open Edges to be Half rounded.

M&L non abrasive paving (rectified endura) tiles 300mm x 300mm x10mm thick machine pressed)light shade 10 mm thick (square/ rectangul-ar) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement complete all as specified and as directed.slurry and point-ed in white or coloured cement and 15mm screed bed in cement mortar 1:4 to match complete al as specified and directed

M & L Demolition of cement concrete in ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified and as directed.

M&L 50 mm thick PCC as in plinth protection / apron type C-1, 1:3:6 (20 mm graded crushed stone aggregate) finishing the surfaces even and fair complete all as specified & directed.

Taking down chowkat with shutter (without taking off shutter from frame) exc 1.5 sqm but n.exc 4 sqm each complete all as specified and as directed.

Taking down chowkat with shutter (without taking off shutter from frame) n exc 1.5 sqm each

Taking down shutter exc 1 sqm but n exc 2 sqm each and remove to store yard complete al as specified and directed.

Taking down easing and adjusting and refixing shutter exc 1 sq. m and n exc 2 sq. m each in same openinG complete all as specified and directed

M & L Steel window/ventilator factory made, made out of mild steel tubuler frame suitable for double shutter i.e. Glazed and gauged shutter. Glazed shutter made out of tubular section with sash bar and gauged shutter made out of tubular section without sash bar including hinges, tower bolt, handle, including grill 10 mm square bar including one shop coat of red oxide primer all as per details shown in drawing No CEPZ/TD-245/01 sheet No 1/1 and CEPZ/TD-246/01 sheet No 1/2 & 2/2 complete all as specified and directed.

M&L Pressed steel frames 125 x 60 mm for doors with one or more rebates including necessary fixing lugs, MS hinges, lock strike plate,etc.,including filling of cement concrete type B-1 ,1:2:4(using 20mm graded crushed stone aggregate) as in filling hollow of frame with plain concrete and hold fast 300mm FI 25 X 6 three numbers each side complete, as specified.

S&F Solid PVC door/window frame of size 50 mm x 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube, above but wood grain printed PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and as directed.

M & L Factory made solid pannel PVC door shutter 28 to 30mm thick with 2 nos12mm thick particle board core moulded with 2mm thick wooden grain printed PVC sheet 30 mm thick (style)5mm thick x15mm wide PVC sheet beading used inside stiles and rails heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stile and plain colour PVC sheet for top rail , lock rail and bottom rail on either side and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rail with suitable PVC sheet beading and jointed together with solvent cement supplying and fixing to frame at site as per specification complete all as specified and directed.

M & L Factory made fully glazed/wire gauge single piece front side PVC printed door shutter 35 mm thick (style) consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain cover pvc "c" channel having a pvc sheet strip of 20 mm width stuck inside with solvent cement for stiles & pvc laminated sheet for top rail,lock rail & bottom rail on either side and gap insert for top rail and bottom rail; panching of prelamnited sheet to be fitted in the mild steel framed welded/sealded to stiles & rails fixed with PVC sheet beading and jointed together with solvent cements. supplying and fixing in frame as per drg No-CEPZ/TD-378/11 SHEET 1/1. The rate include for Stainless Steel wire gauge of 24 gauge to be fitted inside area of stiles and rails all as specified and directed by Eng-in-charge complete all as specified and as directed.

M&L Plain framed factory made 35mm thick shutter of 2nd class hard wood rail & style (two panel) with lock rail and panel of 9mm BWP commercial plywood or 12 mm veneered particle board with commercial veneering on both faces , the size of rail and style as per IS 1003 (Part-1) kiln seasoned and pressure treated all as specified.

Taking down and refixing of chowkhats and frames n.exc 1.5 Sqm (without taking out shutters from the frames) in same opening complete all as specified and as directed.

Taking down and refixing of chowkhats and frames exc 1.5 Sqm and n. exc 4.0 sqm(without taking out shutters from the frames) in same opening complete all as specified and as directed.

M & L Factory Made Solid PVC flush door shutter with wood free EPS core, 28 to 30mm thick (stiles), with 5mm thick prelam PVC Sheet on the front face & 5mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified and as directed.

S&F brass door magic eye: as given specification material resin lens +zinc alloy,top diameter: 31.2mm, botom diameter approx 24mm, pipe diameter approx 16mm total length approx 50mm, inner height approx 36mm application 35 to 60mm thick viewing angle 200 degree of surrounding without opening the door unique design ultra clear view and superior finish, wide angle best in class lens for all round visibility the outsider cannot hide any ware, the back cover protects you from the outsider observing any movements inside easy to instal with inbuilt screw over a wide range of door thickness from 35 mm to 60mm etc required at site complete as directed by Engr-in-charge complete all as specified and as directed.

S&F in Sheet glass ordinary quality 3 mm thick and glazing with oil putty ang glazing clips in squares n. exc 0.50 sqm each pane complete all as specified and as directed.

M & L Sheet glass ordinary quality, ground or obscured or frosted, on one side 3 mm thick and glazing with oil putty and glazing clips in squares n. exc 0.50 sqm each pane complete all as specified and as directed.

Supply and fix in repair GI wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

S&F butt hinges medium weight 100 mm cold rolled mild steel complete all as specified and directed.

S&F aluminium anodised, 150 mm long barrel tower bolt of extruded section complete all as specified and directed.

S&F aluminium alloy, anodised 250 mm long sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 300 mm long mild steel ordinary rat tail rod paltren spring incl roller and roller plate complete all as specified and directed.

S&F 150 mm long aluminium handles , cast type, anodised complete all as specified and directed.

Supply and fix in repair hasp and staple of size 100 mm, aluminium anodised, including bolt to hinge plate and fixed with screws complete all as specified and directed.

Taking down cement plaster on brick wall or concrete surfaces of ceilling etc incl racking out joints hacking for key scrubbing down with water etc. complete all as spd & directed.

M&L rendering 15 mm thick on fair faces of brick work or concrete surfaces including fin facia in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified & directed on external surfaces .

M&L rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement moratr 1:6 finished even and smooth with out using extra cement complete all as specified & directed.

M & L for rendering 10 mm thick on concrete surfaces of ceiling in cement mortar 1:3, finished even and smooth without using extra cement complete all as specified and directed.

M&L for two coat plaster 35 mm thick (20 mm + 15 mm) on rough concrete surfaces of fin, facia, chhajja and similar article in cement mortar 1:3 finished even and smooth without using extra cement in any height including necessary scaffolding complete all as specified & directed. Note :- Two coat plaster shall be carried out as mentioned in clause 14.18 of SSR-2009, Part-I.

M & L for two coat of synthetic enamel paint over a coat of primer on new steel surfaces of any description, not otherwise described over 10cm width or girth including preparation complete all as specified and directed.

M & L for preparation of wooden surfaces of any description exc 10 cm in girth and applying a coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old painted steel surfaces of any description exc 10 cm in girth and applying a coat synthetic enamel paint complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall and complete removal and washing of existing treatment and treating the surface with a coat of cement based putty (JK/Birala wall putty) to make surface smooth including two coats of distempering of wall with distemper oil emulison (any tint) complete all as specefied and directed.

M&L for preparation of new or old plastered surfaces and complete removal and washing of existing treatment and treating the surface with a coat of cement based putty (JK/Birala wall putty) to make surface smooth of wall applyng two coats of cement base paint complete all as specified and directed including curing before and after providing of each coat.

M & L for preparation and complete removal and washing of existing treatment and of old surfaces of ceilling and applying two coats of white wash complete all as specified and directed.

M & L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and directed.

S&F solid chromium plated heavy door chain (weight not less than 249grms) with brass screws to any type of door shutter and frame complete all as specified and directed

M & L Demolition of brick work or stone masonry built in cement mortar including all quoines arches,pillar etc but excluding ashlar facing , dressed stone work and precast concrete articles complete all as specified.

M&L for brick work with sub class 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 all as specified and directed

M & L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in cm 1:4 as in half bricks complete all as specified and directed

M&L water proofing treatment by cleaning of all foreign material such as fungus,mass,dust etc by brushing with steel wire brush and dusting,washing down with water and level the surface with 20mm thick cement mortar 1:4 mixed with and including waterproofing compound as per manufacturer instructions and apply treatment by applying waterproofing membrane APP(atactic polypropylene polymer) modified membrane with non woven polyster reinforcement/mat with thermal insulation with white mineral gravel finished on upper side of weight not less than 3.5 kg/sqm and thickness not less than 3mm, laid by torch application method with overlap 100mm on length side and 100m on the width side over a coat of hot industrial bitumen 85/25 applied @ 1.20 kg/sqm over a priming coat @ 0.40 ltr/Sqm complete all as specified and as directed.

M & L for rendering 10 mm thick on concrete surfaces of roof in cement mortar 1:3, finished even and smooth without using extra cement complete all as specified and directed

M & L Supply only liquid water proofing compound complete all as specified and directed

M & L Dismantling water tanks of capacity exc 250 Litre but not exc. 500 ltr and removing to store complete all as specified and directed

S & F Rotational moulded polythene water storage tank, coloured, tripple layer cylindrical vertical with closed top 500 litre capacity hoisted and fixed in position, including inlet and outlet pipe connections, 20mm dia and 15 mm dia GI pipes medium grade respectively, 20mm GI pipe medium grade over flow pipe 15 cm long wash out with plug,complete all as specified and directed.

S & F 20 mm dia ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms ) complete all as specified and directed

Taking down steel water tubing of 15 mm dia bore incl connection & removal to store complete all as specified and directed

Taking down steel water tubing of 20 mm dia bore incl connection & removal to store complete all as specified and directed

M&L Refixing old steel tubing 15mm and connections in new or old position (Walls, ceiling, floors, etc complete all as specified and directed

M&L Mild steel GI tubing 15 mm bore medium weight with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

M&L Mild steel GI tubing 20 mm bore medium weight with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed

S&F 20mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

M&L Sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 160mm complete all as specified and directed.

M&L Plate rack made of stainless steel 1.00 mm thick of size 600 mm (ht) x 900mm (width) fixed to wall with and including nuts & bolts of suitable size for fixing in wall complete all as specified and directed.

Supply and fix in repair 10 ltrs capacity PVC symphonic action type, flushing cistern, low level, white, with inlet,ball valve, float and handle including brackets, fush pipe of polyethylene of low or high density or PVC. 32 mm dia complete all as specified and directed

Supply and fix in repair Vitreous China squatting pan orissa pattern size 580 x 440 mm white with integral foot rests including connection to trap and to flushing pipe, complete all as specified & directed.

S&F vitreous China wash basin,ovel shape counter sunk type white or in matching colour of tiles ,size 550x400 mm excluding taps,but including 32 mm dia waste coupling chromium plated brass and PVC waste pipe 750 mm long( Minimum), chain and plug and porcelain stopper, brackets for fixing any size, including cutting for and pinning in ends or erecting stand as directed by EIC fixed in repairs complete all as specified and directed

S&F swan neck long type Pillar taps, cast copper alloy 15 mm bore, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs complete all as specified and directed

S&F PVC connection 15 mm dia with PTMT nuts of length 450 mm. complete all as specified and directed

Supply and fix in repair chromium plated (min weight 640grms) bib taps, cast copper alloy with copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

Supply and fix in repair CP stop cock/angle valve cast copper alloy screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore complete all as spd & directed

S&F stop valve chromium plated 15 mm bore fency type with long shank and cup (concealed type) screwed down high pressure ,with crutch or butterfly handle screwed both ends for iron pipe or for union of 15 mm bore complete all as spd & directed .

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed

S & F brass chromium plated shower rose 125 mm size complete all as specified and directed

S&F shall as PTMT fixed with and including chromium plated brass screw and wooden plastic cleats (min wt 300 grms) complete all as specified and directed

S & F curtain rod 25 mm dia of pre painted aluminium with fixing brackets, stops, rollers, knob etc complete all as directed.

M&L Dismantling of cast iron,PVC or reinforced concrete soil waste and drain pipe, 50/75/100 mm dia, jointed in cement mortar or lead and taking out of trenches, if required complete all as specified and directed

S&F PVC (SWR) pipes 75 mm bore, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed

S&F PVC (SWR) pipes 110 mm bore, single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed

S&F PVC (SWR) bends 110 mm bore any radius complete all as specified and directed

S&F PVC (SWR) bends 75 mm bore any radius complete all as specified and directed

M&L Salt-glazed stoneware gully traps of size 150 mm x150 mm, square or round mouthed, tvpe 'P' complete all as specified and directed

S&F PVC (SWR) junction single,(Single T) equal or unequal of 110mm complete all as specified and directed

S&F PVC (SWR) junction single,(Single T) equal or unequal of 75mm complete all as specified and directed

S&F PVC (SWR) vent cowl 110mm complete all as specified and directed

S&F PVC (SWR) vent cowl 75mm complete all as specified and directed

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil complete all as specified and directed

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specfied and directed.

Demolition of cement concrete exc 15 cm thickness of any description under depressed portion of WC and Bath. complete all as specified and directed.

M&L Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering complete all as specified and directed

M&L 100 mm thick PCC 1:4:8 type D-2 (with using 40mm graded stone aggregate) as in floor and finishing even and smooth with using extra cement and spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green complete all as specfied and directed.

S&F 150mm UPVC Pipes (SCH-80) 8KN complete all as specified and directed

M&L Concrete bed to drain pipes (150 mm dia) including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D2 complete all as specified and directed

M&L Returning, filling in, including spreading, levelling, watering & well ramming in layers n exc 25 cm with any type of soil complete all as specified and directed

Removing excavated material (soil) to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed.

S&F bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed

M&L Cutting into existing man hole for connection new drain pipe ,making good to walls and rendering ,cutting out existing branch, channel, and making good benching in cement concrete 1:2:4 type B1 and smooth finish, forming benching as required for internal dia of pipe 160 mm all as specified and as directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed

M & L for precasted RCC 1:2:4 type B-1 using 20mm grade crushed stone agregate manhole cover slabs of size as per site requirement or as directed by Engr-in-Charge in circular/square/rectangular size as per site requirement and placing on manhole/soakage well/septic tank complete all as specified and directed.

M&L Mild steel TMT bars 8 mm dia and over, cut to length, bent to shape required incl crancking, bending spirally for hooping columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed

M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded aggregate)as in foundation filling and mass concrete complete all as specified and directed

M&L PCC 1:2:4 type B-1 ( using 20 mm graded crushed stone aggregates) as in copings, ,bed plates and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed

S&F mild steel angle or Tee section as in supports for shelves /water cooler etc and similar articles conforming to Fe-290 Gde E-165, including embeded in wall complete all as specified and directed.

M&L Rooting out trees, flora & fauna and foliage as grown on RCC roof surfaces and brick walls by cutting hole into slabs/walls for digging out roots and using chemical to burn deep rooted tree roots etc and making good dirturb portion of wall/roof with cement concrete 1:2:4 type B 1 complete all as specified and directed.

S&F 18mm thick ultra voilet printed PVC board (weight not less than 12 Kg/Sqm) duly edge bonded with 0.8mm thick PVC taping as in cupboard/kitchen cabinet shutters fitting complete all as specified and as directed by Engineer -in-Charge

Dismantling of old asbestos cement corugated,semi corrugated etc) sheets in roof coverings complete all as specified and directed

S&F mild steel angle iron or hollow section fixed in wall for chowkhats with hold fast including welding,angle iron support for chajjas/slab or similar works as specified or as directed by Engr-in-Charge

M&L for Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws/type hooks as specified including dismantling of old sheets of any description complete all as specified and directed

S&F mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc complete, drilled for fixing of steel sheeting or other covering doors etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings as specified and as directed by Engr-in-Charge

M&L for continuous (piano) hinges , mild steel bright finish or electro galvanised, width of flaps 30mm (when open) (ISI marked complete all as specified

Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power socket and bulk head fittings) on surface wiring on wooden batten/ casin caping complete including fixture and fittings such as switches, ceiling roses, pandents holder , regulators, sockets, lamp holder, buzzer , light fittings and defective main switch/DB/MCB/Metal plug etc by unscrewing carefully from board etc and making good disturbed surfaces of wall, floors, complete all as specified and directed.

M & L Point wiring for light/fan point controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkum boxes having thickness as specified 3mm bakalite laminated sheet for switches and sockets, including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) (b) On RCC roof ceiling PVC conduit shall be provided on surface for fan with proper fixing clips e all as specified and directed.

All as per above item no 110.00 here in before but for one 5 pin socket outlet 5 amp on independent board all as specified and directed.

All as per above item no 110.00 here in before but for one 3 pin socket outlet 5 amp on same board all as specified and directed.

M & L All as per Srl No 110.00 here in before but for call Bell point complete all as specified and directed .

M&L Point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS with and including PVC rigid conduit (medium grade) having thickness as per IS code with all fittings including galvanised pressed steel sunkum boxes having thickness as specified 3mm bakalite laminated sheet for one 3 pin socket outlet 15 Amp on independent board including 2.5sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including cutting, chiseling for concealed piping and making good disturbed surface area and white wash/colour wash to matching with the existing colour complete all as specfied and directed. Note : (a) Colour coding is to be maintained (Ph-Red, N-Black, Half -Yellow, Earth- Green) complete all as specified and directed.

S&F Switch piano flush type one way 5 Amps single pole 240 volts complete all as specified and directed.

S&F Switch piano flush type one way 15 Amps single pole 240 volts complete all as specified and directed.

S&F Switch bell push flush type 5 Amp 240 volt complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 amps flush type 240 volt complete all as specified and directed.

S&F socket outlet 2 in 1, 3 pin 5 and 15 amps flush type 230 volt complete all as specified and directed.

S&F Lamp holder PVC/Polycarbonate type with back plate having matching colour to holder for angle/batten fittings (ISI marked) complete all as specified and directed.

S& F bell and AC heavy duty 230 volts single pole complete and all as specified. all as specified and directed by Engineer-in-Charge.

S & F Ceiling rose, 65x50mm three therminals isolated body (ISI marked) complete all as specified.

M& L celling fan regulator electronic socket type 5 stage speed variation ISI marked complete all as specified and directed.

M & L LED bulkhead 10 watt connecting electricaly to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75 sqmm all as required complete all as specified and directed.

S & F in replacement of CFLs with LED smart Lamp, B22 type,14 watt complete all as specified and directed.

Supply and Fix in replacement existing UNSV tube light fitting with LED 20W inverter batten type fitting 4 feet long aluminium extruded housing, charging time 10-12 hours and back up time 04 hours, IP-20 ,rated voltage 230 V, 50 hz, system wattage 20W +/- 10%, system current less than 102 mA, power factor more than 0.95, system lumen efficiency 100lm/watt,CCT 6500K, CRI more than 80, THD less than 30%, driver efficiency more than 85% complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed. Notes: (i) LM79 report from third party (instead of company in house lab) NABL/UL accredited lab (ii) LM 80 report from LED manufacturer (iii) Test certificates to be submitted before commencement of work/ claiming for payment . (iv) Warranty certificate for minimum 2 years to be submitted from OEM.

S&F Sheet metal enclosure powder coated factory made (Double door) for DBs, single pole and neutral, 240 volts, 50 Hz, 12 way with 200Amps rated copper bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning, complete all as specified.

M & L MCB single pole 240 volts any rating from 20 to 40 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

M & L MCB single pole and neutral 240 volts any rating from 6 to 40 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 60cmx60cmx6 mm thick buried directly in ground (Earth pit not less than 2.25 Mtr deep below normal ground level )with top edge of the plate not less than 1.5 Mtr below normal ground level connecting with galvanized iron GI earth wire 4mm dia by means of bolt nut check nuts and washers of galvanized iron and provision of GI tubing medium grade (ISI marked)of size 15mm for protection of GI earth wire upto test point, 20mm dia GI light grade watering pipe with funnel and wire mesh, RCC pit cover of size 300x300x40mm reinforced with XPM having weight not less than 4Kg/sqmm including 6mm thick MS bar handle made to shape, PCC pit with 1:3:6 type C1 with angle iron frame made of angle iron of size 40x40x4mm, adequate qty of charcoal dust and salt layers all around the earth plate, earth work in any type of soil, complete all as specified in plate No 3 of SSR Part-I and all as specified or indicated including testing on completion.NOTE :-Rates inclusive of necessary earth work, PCC pit, RCC cover, funnel with watering pipe, GI earth strip upto 7.5 m long for connecting to test point etc. all as required at site for complete earthing).

M& L for providing /cutting the round/square hole of required size in wall and finishing the same disturbed surface to match the existing finishes and including supply & fixing ventilation fan AC sinlge phase 230/240 volts of size 250 mm sweep, 900 RPM complete including grouting the ragged bolts in wall and including PVC insulated 1.5 sqmm copeer cable connecting to ceiling rose all as required or directed and writing MES no with black synthetic enamel paint 2 cm high

Supply and laying in replacement of existing unserviceable/ burnt submain wiring alongwith two single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of size 6 sqmm drawing into and including concealed PVC rigid non metallic conduit of 20mm dia , 1.8 mm wall thickness and single core cable PVC insulated and unsheathed cable with copper conductor FRLS (multistrand) of 6 sq mm as earth wire including cutting chases in brick wall, rendering in cement mortar 1:4 and making good the disturbed surfaces to match existing complete all as specified & directed. Note: (i) Two runs of 6 Sqmm single core PVC insulated copper conductor cable(FRLS) and one run of 6 sqmm copper conductor cable (FRLS) as a earth lead and one run of PVC conduit of 20mm dia , 1.8 mm wall thickness wiil be measured as a one unit. (ii) Proper colour coding is to be followed as per IS Specification. (iii) wiring shall be concealed/ on surface with rigid PVC conduit medium grade.

S & F in replacement of old unsv sheet metal enclosures distribution boards, double door three phase 415 volts 4 ways vertical TPN DB of comprising yhree phase four wire copper strip bus bar of appropriate capacity complete all as specified and comprising of the following (a) MCCB FOUR POLE 100 AMPS AC 415 VOLTS 25 KA=01 NO as incoming and 12 nos. MCB SP 40 Amps, C series as outgoing (Note :- (i) The DB shall be VTPN series of Schenieder Cat Part No :- A9HVD04K or equivalent in any of the make mentioned in list of product. (ii) The DB shall be flush fixed, and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii) connection ofthe MCCBs/ MCBs with cable shall be made throughapproprite size pin/ bottle type thimble complete all as specified and directed.

Supply and laying for XLPE insulated, armoured, heavy duty electric cable with aluminum conductor, 1100 Volts grade, of size 25 Sqmm 4 core and taking down of old unservicable /brunt electric cable complete all as specified and directed. Note:- Earth work including excavation, returning filling , removing, sand cushioning, GI pipe,brick covering for mechanical protection of cable etc will be measured and paid for separately under respective items of schedule.

Excavation in trenches n. exc. 1.5 metre wide and n. exc. 1.5 metre in depth for laying of UG cable and getting out in soft/loose soil complete all as specified and directed.

Sand cushioning for under ground cable upto 8 cm before laying the cable and 15 cm after laying and stretching the cable and punned down to form a bed.The punning shall be done by hand complete all as specified and directed.

Material and labour for sub class 'B' bricks well burnt old size laid dry flat perpendicular to the length of cablefor protection of cable complete all as specified and directed.

Supply and fixing in replacement of GI tubing medium grade of 40 mm nominal bore of pipe in trenches/under roads/ under culverts/under paths/under floor/on walls /with pole in new position with screwed sockets joints, together with all tube fittings complete all as specified and directed .

S & F bldg secuirty light fitting energy saving high efficiency LED street light fitting 25 Watts, 5700 K, IP 66, having pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, prismatic polycarbonate cover complete including GI bracket of size 32 mm dia bent to shape having length on less than 1.5 mtr fixing with clamp etc and making connections using cord flexible 3 core copper cable of size 23/ .0076 from ceilling rose/ PVC connector to light fittings or as directed by Engr-in-chrage. Notes :- (i) Contractor shall produce LM79 & LM 80 test report from OEM owned NABL accredited laboratory. (ii) Contractor shall give guarantee/ warranty of complete fitting/ fixture for minimum 2 years from the date of completion. (iii) Contractor shall arrange complete material at site for approval of GE before incorporation in the work. (iv) Driver shall be IP 66 degree of protection potted seal type with inbuilt SPD and external SPD of capacity 10 KV to be provided in addition to inbuilt.

Notes : The Schedule of Credit amount shall be deducted from the total of this schedule(BoQ) to arrive at Contract Sum.

VIKRAM SINGH MANHAS

GANDOTRA CONSTRUCTION CO

M/S SALARIA BUILDERS

M/S Raghuvanshi Builders

Ms Dalip Kumar and Co.

Raghbir chand