Augmentation of 10 Numbers of various 33/11 kV Substations in LESA Transgomti area including switch gear room extension, if required, in Lucknow district of MVVNL.

Amount

Carrage from Lucknow Store to Various sites, within 50 Km.

5 MVA T/F

Panther Conductor

33 KV VCB 800 Amp 750 MVA

33 KV CT 200/100/1 amp

Single T/F Control Panel

Single Feeder Control Panel

11 KV VCB I/C CTR 600/300/5 amp, 350 MVA

11 KV VCB O/C CTR 200/100/5 amp, 350 MVA

Bus Coupler 350 MVA

STP 11 Meter

Rail pieces 8 Meters long (105 lbs per meter)

Supply of materials at various sites

33 KV 3x300 sq mm XLPE Cable

11 KV 3x185 sq mm XLPE Cable

11 KV 3x300 sq mm XLPE Cable

33 KV 3x300 sq mm XLPE O/D J/Kit

33 KV 3x300 sq mm XLPE I/D J/Kit

11 KV 3x300 sq.mm Cable Jointing Kit I/D

11 KV 3x300 sq.mm Cable Jointing Kit O/D

11 KV 3x185 sq mm XLPE O/D J/Kit

11 KV 3x185 sq mm XLPE I/D J/Kit

Single core cable 1x630 sq mm

33 KV Line Isolator

33 KV Bus Isolator

33 KV Lightening Arrestor

24 Volt Battery and Battery Charger with Cabinet.

Control Cable 2x2.5 sq mm

Control Cable 4x2.5 sq mm

Control Cable 6x2.5 sq mm

Errection and fabrication of facilities (works)

Errection and fabrication of Bus Bar Gantry as per Schedule -40

EARTHING OF S/S SWITCH YARD (30x25 Mtr) as per Schedule-45

EARTHING OF S/S SWITCH YARD (20x6 Mtr) as per Schedule-45 (a)

Power T/F PLINTH SIZE 4X3X1.3 Mtr as per Schedule-44

Dismanteling of Ditribution TF Plinth

Pipe boring Earthing including all materials required as per schedule Schedule-53

Dismanteling & dump to safe place of Power T/F (5MVA/8MVA) including draining of oil from the radiator & opening of radiator if required (oil drum arrange by the contractor)

Dismantleing and reinstalling of netural stand & cable stand with grouting and plinthing

Errection of 5 MVA T/F including clamps, connectors, L-piece etc.

Errection of 10 MVA T/F including clamps, connectors, L-piece etc.

Various Stinging/ Jumpering of Panther Conductor inclung clamps and connectors

33 KV VCB 800 Amp 750 MVA

33 KV CT 200/100/1 Amp including connectors, tapes, etc.

Plinth & Foundation of 33 KV VCB

Single T/F Control Panel

Single Feeder Control Panel

11 KV VCB I/C CTR 600/300/5 amp, 350 MVA

11 KV VCB O/C CTR 200/100/5 amp, 350 MVA

Bus Coupler 350 MVA

Earthing of indoor equipments by means of M.S strip 50x6mm

Replacement 11 KV CT 600/300/5A as installed make

Excavation of pit for STP exposure

Errection and fabrication of Double Poles, cable exposer type as per schedule -29

Grouting and plinthing of STP as per schedule -29

Earthing of Double pole with earth rod as per schedule -29

Painting of double poles as per schedule -29

Fabrication and errection of Line/Bus Isolator Structure including all materials as per schedule 41

Grouting and plinthing of Line/Bus Isolator structure

Painting of Line/Bus Isolator structure

Fabrication and errection of LA/CT/PT Isolator Structure including all materials as per schedule 42

Grouting and plinthing of LA/CT/PT Structure

Painting of LA/CT/PT Structure

Fabrication of Cable Stand (Schedule-49)

Grouting and plinthing of Cable stand

Painting of cable stand

Fabrication and errection of neutral stand including materials (Schedule-52)

Grouting and Plinthing of neutral stand (Schedule-52)

Painting of neutral stand (Schedule-52)

11/33 KV Cable Laying with all Material For Single ckt,3x185 sq mm and above size (Schedule-08)

33 KV Cable Laying with all Material For Double ckt,Size 3x300 sq mm (Schedule-09)

11 KV Cable Laying with all Material For Double ckt,Size 3x300 sq mm (Schedule-09)

Opening & Dehoisting of existing hoist cable on S/G /cable stand including the cost of digging of pit for removal of cable and laying the same cable again aprox. 10 with rehoisting.

Cable Hoisting on Cable Stand / Switchgear

33 KV High Pressure Testing

11 KV High Pressure Testing

11 KV Cable Hoisting with MS Pipe including all materials as per Schedule-33 on double pole

Control cable Trench per Mtr 12" wide including all materials as per Schedule-54

Control cable trench Trench cover 0.5 Mtr long 300 mm Wide for 12" wide trench as per Schedule-55

Fixation of Control Cable Tray

Laying of control cable

Testing of equipments

Carrage of 5 MVA T/F from Various sites to Lucknow Store , within 50 Km.

Carrage of 8 MVA T/F from Sarvoday Nagar to Lucknow Store

Shifting of equipments with minimal interruption of power supply including all the materials as control cable etc. for extension of control room or where ever required

Extension of Control room Building

Excavation in foundation in ordinary soil (Loam Clay or Sand) including lift upto 1.5m and lead upto 30m and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of the foundation work.

Sand filling in plinth including supply of necessary quantity of local sand from outside the UPPCL premises including watering, dressing etc. Rate to include cost of all materials, labour and T&P etc. required for proper completion of work.

Earth filling under floors and/or sub station area including cost of earth when obtained from with in 8 km outside UPPCL area including its roylty and carriage including watering, ramming in 20cm layers and dressing of earth etc. all complete

Concrete with 4cm gauge I class brick ballast (class 150) , coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 12:6:1 in foundations and under floors including supply of all materials, labour and tools and plants etc. required for proper completion.

Cement concrete with 2cm gauge approved hard stone ballast, coarse sand (F.M. 1.8 to 2.5) and cement in proportion of 4:2:1 including supply of all materials, labour,side shuttering if required and T&P etc. required for proper completion of work

Concreting of 40 mm thick RCC trench covers in mild steel frame work with RCC 1:1.5:3 in Cement,Chopan coarse sand (F.M. 1.8 to 2.5) and 2cm gauge graded hard stone ballast with 3mm thick floating coat of neat cement finish on top of cover complete with all labour, materials and placing the same in proper position at required location of cable trench within the substation area.

Concrete work with 40 mm gauge brick ballast obtained from breaking brick bats (brick bats supplied by the department free of cost) in proportion of 12:6:1 as in item 273 above including cost of all labour, materials, T&P etc required for proper completion of work.

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in lintels of doors and windows, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P.

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in slab, excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in lighter beams i.e. having span upto 6m , excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in raft foundation and footings , excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P.

RCC work with cement approved coarse sand (F.M. 1.8 to 2.5) and 2 cm gauge graded approved hard stone ballast like grainite, quartzite etc from Dalla, Jhansi or other quarries and approved coarse sand in proportion 1:1.5:3 in RCC T beam-slab and column , excluding supply of reinforcement & its bending but including its fixing and binding the same with binding wire, including cost of all other materials labour and T&P .

First class brick work in 1:6 cement and coarse sand (F.M.1.8 to 2.5) mortar in foundation and plinth including supply of all materials, labour & T&P etc. required for proper completion of work.

First class brick work in 1:6 cement and coarse sand (F.M.1.8 to 2.5) mortar in Super structure including necessary cutting and moulding of bricks as required and also including honeycomb brick work, thickness of wall not to be less than one brick including supply of all materials, labour & T&P etc. required for proper completion of work.

First class brick work in 1:4 cement and coarse sand (F.M.1.8 to 2.5) mortar in Super structure, thickness of wall 1/2 brick(115mm) including supply of all materials, labour & T&P etc. required for proper completion of work.

Brick work in foundation & plinth with old dismantled bricks (supplied by department free of cost) and coarse sand of F.M. 1.5 to 2.0 mortar in 1:6 including supply of all other materials, labour, removing mortar & cleaning of old & used bricks,T&P etc complete.

Mild Steel or Iron work in heavy sizes such as trusses built up gates, door frames, record, racks roof work gates etc. wrought to required form including holes rivetting or welding where necessary and also fixing in proper position and alignment including cost of all materials supplied by contractor.

TMT/Tor steel in plain work such as reinforced concrete or reinforced brick work (when not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage, bend, hooks and authorized overlapping shall be measured. (Steel shall be arranged by the contractor)

Providing and fixing steel glazed window and ventilators of standard rolled Mann or Mahavir steel sections conforming to IS 7452-1974 as per drawing joints metered & welded with 100x14x3.15 mm holdfast embedded in cement concrete block 15x10x10 cm. Size of 1:3:6 proportion I.E. First part of cement 3 part of approved coarse sand & 6 part of graded stone (aggregated 20mm. Nominal size) S/F of glass panes of plain pin headed 4mm. Thick nuts glazing clips and special putty of approved make complete and including a cost of red oxide paint. The fabrication should conform to I.S.1038-1975. (Aluminum beading with rubber packing included).

Supply and fixing galvanised mosquito proof jali (16x24 gauge) with M.S. flat of 20 x 3 mm. size, on both sides screwed or welded to window or door frame

Providing M.S. Frames work, rack etc for R.C.C. Trench covers and edging with M.S. angles and M.S reinforcement including cutting, bending and welding as per approved drawing. The rate is including cost of all labour, materials etc. as required for proper completion of the work.

Fixing and grouting of trench edging in proper level and alignment including cost of all labour, and T&P etc. required for proper completion of the work but excluding cost of C.C.

Making expansion joints with 24 gauge Aluminium sheet in walls with necessary cutting shaping of bricks if any & covering joints by 10 mm Ply wood , 150 mm wide.

12 mm thick plaster with cement mortar consisting of one part of cement & four part of coarse sand (1:4), minimum thickness not to be less then 10 mm including supply of all material, labour and T&P etc for proper completion of work.

12 mm thick plaster with cement mortar consisting of one part of cement & six part of coarse sand(1:6),minimum thickness not to be less then 10 mm including supply of all material, labour and T&P etc for proper completion of work.

Add for extra labour and materials for plaster over rough face of one brick thick wall.

S/mixing approved water proofing compound (CICO,DR FIXIT etc) in cement mortar in plaster or concrete work in the proportion as recommended by the manufacturer

Providing (12x15)mm section groove in plaster at the junction of ceiling & walls, including all material, labour and T&P etc. required for proper completion of the work.

Making drip course (25x12) mm in 1:2 cement and course sand including supply of all materials, labour and T&P etc required for proper completion of work.

3 mm thick floating coat of neat cement finish including supply of all materials,labour and T&P etc. required for proper completion of the work.( cement consumtion 0.044 bag/Sq.m.)

2.5 cm thick 1:2:4 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and excluding base concrete and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work.

Providing and fixing glass strips of 3.15 mm thickness & 25mm depth in joints of floor and skirting at the time of laying floors, flush with floor level including supply of all materials, labour& T&P etc. completion required for proper completion of work.

Providing and laying 20 mm. thick Kota stone in flooring or skirting over base cement mortar 1:4 mix and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete and including supply of all materials labour and T&P etc required for proper completion of the work.

Painting or varnishing new iron work in small areas or new wood work with one coat of ready mixed priming paint and one coat of approved superior quality ready mix paint "Luxol" or equivalent brand or varnish including supply of all materials, labour and T&P etc. required for proper completion of the work. Paint to be used should conform to the I.S. 103-1950.

As in item 13.01 above but for every coat after first coat

One priming coat and one coat oil bound distemper on new work including supply of all materials,labour and T&P etc. required for proper completion of the work.

Every coat after first coat of oil bound distemper including supply of all materials,labour and T&P etc. required for proper completion of the work. but for every coat after the first coat.

Applying Birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ICI or equivalent brand for smoothening and levelling of the surface as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work.

Applying Birla or equivalent putty on new interior or exterior surface over one coat of water based cement primer of ICI or equivalent brand for smoothening and levelling of the surface as per requirement and direction of Engineer I/C including cost of all material, labour, T & P etc required for proper completion of work.

Painting one coat with APEX or equivalent brand weather coat paint on new wall surfaces (well prepared with Birla putty and one coat of primer ICI or equivalent which shall be paid separately) including thorough washing with water including cost of all materials, labour, T&P required for proper completion of work.

For every coat of additional APEX or equivalent brand weather coat paint including thorough washing with water including cost of all materials, labour, T&P required for proper completion of work.but for every coat of additional APEX or equivalent brand weather coat paint .

Dismantling brick work or stone work in lime or cement mortar and including stacking of materials as directed by the Engineer-in-charge within a distance of 60 metres.

Dismantling existing plaster including disposal of refuse as directed by the Engineer-I/C within a distance of 60 M.

Dismantling reinforced cement concrete or reinforced brick work, including stacking of dismantled materials as directed by the Engineer-Incharge within a distance of 60 metres.

Scrapping old white or colour wash or distemper including disposal of refuse as directed by the Engineer-I/C within a distance of 60 M.

Providing and fixing of 110 mm dia PVC pipe 4 Kg/ Sq.cm for with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work.

Cleaning, Repairing of visible cracks/pot holes/uneverness using polymerised motar (Addcon chemical or Star equivalent make) as per manufactures specifications including supply of all material, labour and T&P etc for proper completion of work as per direction of Engineer Incharge.

Providing and Applying one coat of DI PRIMER for prime sealing (Addcon or Star equivalent make) over the prepared surface using a brush. if the surface is very porous two coats could be applied with a gap of 2-3 hours between each coat. one coat as per manufactures specifications including supply of all material, labour and T&P etc for proper completion of work as per direction of Engineer Incharge.

Providing and applying after the primer coat is completely dried apply two coats of ENIROOF SPR®. It is recommended to apply the 2nd coat after the 1st coat is totally cured with GLASS FIBRE REINFORCEMENT embedded into 1st coat of ENIROOF SPR® while still wet. ENIROOF SPR® could be diluted up till 15 – 25 % for 1st coat and 10 – 15 % for 2nd coat to make material workable and get the desired coverage. Follow application instructions of KOSTER coating being installed. Embed KOSTER Glass Fiber Mesh into the fresh first layer. After the first layer has cured, cover with subsequent layers. Installed sheets of KOSTER Glass Fiber Mesh must overlap each other by at least 2 inches (ENIROOF SPR® Make) as per manufactures specifications including supply of all material, labour and T&P etc for proper completion of work as per direction of Engineer Incharge.

Wiring point for light with 1.0 sq.mm FR PVC insulated multistrand single core copper conductor cable in heavy duty (2 mm thick) PVC conduit concealed in wall complete with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit, 6amp. Piano type switch and ceiling rose / angle / batten holder on 3mm. thick phenolic laminated backelite- sheet etc. complete in all respect,as directed .

Wiring point for fan/fresh air fan (light duty exhaust fan) with 1 sq. mm. FR PVC insulated multistrand copper conductor cable in PVC conduit concealed in wall, complete with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit, Piano type switch and ceiling rose on 3mm. thick phenolic laminated backelite- sheet etc. complete in all respect,as directed .

Wiring point for plug with 1.0 sq.mm FR PVC insulated multistrand single core copper conductor cable in heavy duty (2 mm thick) PVC conduit concealed in wall complete with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit, 6amp. Piano type switch and 5pin socket etc.complete on 3mm. thick phenolic laminated backelite- sheet etc. complete in all respect,as directed .

Wiring point for exhaust fan with 1.5 sq.mm FR PVC insulated multistrand single core copper conductor cable in heavy duty (2 mm thick) PVC conduit concealed in wall complete with 1.5 sq.mm. FR PVC insulated multistrand copper conductor cable as earth wire drawn inside the conduit, 15amp. Piano type switch and ceiling rose / angle / batten holder on 3mm. thick phenolic laminated backelite- sheet etc. complete in all respect,as directed .

Supply and wiring of submains with 2 nos. 2.5 sq.mm & with 1 no earth continuity wire of 1.5 sq.mm FR PVC insulated 1100V grade insulated multistrand single core copper conductor cable in 20mm dia heavy duty (2mm thick) PVC conduit concealed in wall complete,including supply of all materials, labour and T&P etc.required for proper completion of the work.

S/F of power plug with 15A/240V flush type switch and 5 pin 15A/250V flush type universal socket in suitable MS box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3 mm thick fixed with brass machine screw and cup washer.

S/F hexagonal fan box with hexagonal side of approx 80 mm in length fabricated from 16 SWG MS sheet incorporating 10 mm dia. M.S. round bar duly bent for supporting fan hanger duly painted with red oxide and screwing arrangement with wiring conduit laid in the RCC roof before concreting along with supply of all material, labour, T&P etc. required for proper completion of the work.

Supply and installation of LED tube light with fittings, box/channel type T-5 energy saver without a refelector & without end covers for 1 no. 20 watt T-5 lamp/Tube with 1x 20 watt T-5 lamp/Tube (Crompton, Bajaj, or equivalent make) complete in all respect

Supply and fixing of approved quality ceiling fan (Crompton, Bajaj, or equivalent make) including all cost of all materials, labour, T&P etc. for proper completion of the work.

Supply and fixing of approved quality exaust fan (Crompton, Bajaj, or equivalent make) including all cost of all materials, labour, T&P etc. for proper completion of the work.

GST SHALL BE PAID EXTRA

CAPITAL ELECTECH PVT LTD