CERTAIN MINOR WORKS AND SPECIAL REPAIR WORK AT KALINA AND DGQA VIKHROLI UNDER GE NORTH MUMBAI

Amount

Taking down cement plaster on brick or stone walls, ceilings etc., without disturbing brick work, including raking out joints, hacking for key, scrubbing down with water and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Material and labour for 10mm thick rendering with cement mortar 1:6 on fair faces of brick or concrete surfaces and finished even and smooth without using extra cement etc complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering 5 mm thick in cement mortar 1:3 on ceiling surfaces and finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer etc complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for preparation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkats or frame with shutters not exceeding 1.5 sqm each (without taking off shutters from the frames) including all fittings & removing clear off site complete all as specified and as directed by Engineer-in-Charge.

Supply and fix solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with M.S. square tube and fixing in opening as per specification & drawing on Serial Page No 180 of SSR Part II (pertaining to item No 08095) and edges to be painted to match with prelam sheet complete all as specified and as directed by Engr-in-Charge. Make : RAJSHRI / SINTEX / TUFFFLON / M/s Navratan Specialty Chemical LLP – ‘Brand : GIZA’

Supply and fix factory made solid panel PVC door shutter 30mm thick (style) consisting of frame, made out of M. S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC `C` channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at site as per specification & drawing on Serial Page No 176 of SSR Part II (pertaining to item No 08080) complete all as specified and as directed by Engineer-in-Charge. Make: M/S Rajshri Plastiwood, Indore/M/S Sintex Industries Ltd/M/S TUFFFLON/M/S Dura Plast Extrusion

Supply and fix Stainless steel butt hinges medium weight of size 100mm all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix floor door stopper of aluminium alloy body and tongue, anodized with hard drawn steel spring 150mm size, complete all as specified and as directed. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix Stainless steel butt hinges medium weight of size125mm all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodised barrel tower bolt of extruded section size 150mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix extruded aluminium alloy handles fabricated types, anodised, of size 150 mm long complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix aluminium anodized sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300mm long, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Taking down shutter carefully, area exceeding 1.0 sqm but not exceeding 2.0 sqm and refixing In the same opening including all fittings etc complete all as specified and as directed by Engineer-in-Charge

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing),depositing debris out side MD land complete all as specified and as directed by Engineer-in-Charge.

Material and labour for non skid coloured ceramic tiles, 7 to 8mm thick (square/rectangular), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for coloured glazed ceramic tiles of size 350mm x 250mm x 7 mm thick / 450mm x 350mm x 7mm, on vertical surfaces etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for 25mm thick cement concrete nominal mix 1:2:4 (using 20mm graded stone aggregate) type B-1 as in levelling course,sub base, floor, pavings, path, hardstanding, slope as required etc and finishing the surface even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repairs, 100 mm bore outlet, CI floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge. Make : NECO/Sighal iron Foundry/Bengal iron Co/Dhatu Udyog/Kapilansh

Supply and fix in repairs, UPVC Nahani trap,100 mm dia with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) etc, complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex/Astral

Supply and fix mild steel tubing medium grade 15mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed to wall / ceiling or laid in floor with suitable size GI clamps including taking down existing GI pipe and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix mild steel tubing medium grade 20mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed to wall / ceiling or laid in floor with suitable size GI clamps including taking down existing GI pipe and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix mild steel tubing medium grade 25mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed to wall / ceiling or laid in floor with suitable size GI clamps including taking down existing GI pipe and making good disturbed surfaces as per existing surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix in repairs stop valve or angle cock, cast copper alloy, fancy type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repair vitreous china squatting pan Orissa pattern of size 580 x 440mm white with integral foot rest, 'P' or 'S' trap front and back inlet and including connection to trap and to flushing pipe, anti syphonage pipe etc (excluding flushing cistern & flush pipe) all as specified and as directed by Engineer-in-Charge. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/Johnson

Supply and fix in repairs PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, including flush pipe of polyethylene of low or high density or PVC 32mm dia including connection to pipe and fixing of chains and pull or lever complete all as specified and as directed. Make : Slimline/Commander/Hindustan.

Supply and fix in repairs vitreous china wash hand basin, white, flat back of size 580 mm x 450 mm excluding taps, waste pipe, chain and plug and porcelain stopper including brackets, chromium plated waste coupling, waste fitting etc, cutting for and pinning in ends of brackets, connecting to supply and waste pipe complete as specified and directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware /Johnson

Supply and fix in repairs pillar taps fancy type cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repair PVC (SWR) single socketed rain water/soil waste pipes, type B, with rubber ring joints 110mm dia , fixed to wall or in weep holes including scaffolding upto any height complete all as specified and directed. Make: Finolex/Prince/Kisan/Supreme/Astral

Supply and fix in repairs PVC (SWR) bends any radius, 110mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex/Astral

Supply and fix in repair PVC connection, 15 mm size 450 mm long, both end socket fix and PTMT check nuts complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix in repair, Soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and as directed by Engineer-in-Charge. Make-Cera/Hindustan/Parryware/Jaguar/Hindware /Johnson

Supply and fix in repair vitreous china bowl urinal, flat back, size 465 x 355x 265 mm white (minimum), with grating and urinal for discharge pipe, waste pipe complete including providing and fixing plugs, bedding urinal against wall in CM securing urinal to plugs with and including 60mm long brass screws, pointing around, fixing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and as directed by Engineer-in-Charge. Make: Cera/Hindustan/Parryware/Jaguar/Hindware /Johnson

Supply & Fix in repairs viterous china urinal partition, white of size 310 x 700mm complete all as specified and as directed by Engineer-in-Charge. Make: Cera/Hindustan/Parryware/Jaguar/Hindware /Johnson

Supply & Fix in repairs vitreous china squatting plate urinal white (exluding flushing cistern,flush pipe and waste pipe) Make:- Cera/Hindustan/Parryware/Jaguar/Hindware /Johnson

Supply and fix 15 micron coloured aluminium sections for windows, ventilators, doors, partitions etc including fabrication of frame & shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc including all accessories such as glazing clips and rubber beadings for fixing glass panes in frame complete all as specified and as directed by Engineer-in-Charge. Make : Hindalco/Indal (Indian Al Coy)/Jindal/Associated Profile & Aluminium Ltd/Ajit India Note: (i) Glass panes will be measured & paid separately. (ii) Rubber beading will not be weighed.

Supply and fix 4.0mm thick figured glass, pin headed type ordinary quality fixing with oil putty and glazing clip, in squares, not exceeding 0.5 Sqm in each pane complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Supply & Fix granite slabs 20mm thick, table rubbed and polished, fixed independently to walls duly supported with partition walls, made to shape as directed at site, including nosing of edges, complete as in platform for oval shaped counter top wash basin complete all as specified and as directed by Engineer-in-Charge

Supply and fix in repairs vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with PVC seat cover, chromium plated hinges & nuts including ‘P’ trap / 'S' trap, connection to drain flushing pipe, antisyphonage pipe complete all as specified and as directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/ Johnson

Supply & Fix in repairs Plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and as directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/ Johnson

Supply and fix in repairs 15mm bore two way bib taps, fancy type, chromium plated, cast copper alloy, long body with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule with or without letter HOT or COLD with long screwes shanks all as specified and as directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix in repair, health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook, including making connection and fixed in position all as specified and as directed by Engineer-in-Charge. Make-Prayag/Parryware/Jaquar

Material and labour for preparation of undecorated wall surfaces and applying 1.5mm thick wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for preparation of undecorated ceiling surfaces and applying 1.5mm thick wall care putty complete to smoothen the underneath surfaces complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for 15mm thick rendering in cement mortar 1:3 mixed with water proofing compound in sunken floor including vertical surfaces upto 450mm height including applying a coat of Raincoat solution of make Dr Fixit or equivalent with uniform surfaces and supply and fix vitreous china squatting pan Orissa pattern pan of size 580 x 440mm white with integral foot rest, 'P' trap and connecting to flushing pipe, anti syphonage pipe etc (excluding flushing cistern) and connecting piece of CI pipe as per required upto T/Y joint including filling PCC 1:4:8 type D2 and over 40mm thick PCC 1:2:4, type B0 for floor with uniform surfaces and GI spout, medium grade with 50mm dia to provide that 450mm long to be extended from front surface of wall complete all as specified and as directed by Engineer-in-Charge.

Supply and fix 32mm dia low density polyethylene pipes (LDPE) of pressure rating @ 6 kgf/ cm2 fixed to wall complete all as specified and as directed by Engineer-in-Charge.

Material and labour for post construction Anti-termite Treatment of soil under existing floors using chemical emulsion at the rate of one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Anti-termite Treatment of treating the soil along with internal/external wall /perimeter of the building with chemical emulsion at the rate of 2.25 litre per linear metre including drilling and plugging holes etc in apron complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation, laying pipes etc or for shaft, walls, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in hard/dense soil complete all as specified and as directed by Engineer-in-Charge

All as per item No. 51 above but depth exceeding 1.50M but not exceeding 3.00m

Removing excavated soil to a distance exceeding 1.5 Km but not exceeding 5 Km and depositing where directed outside MD land complete all as specified and as directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick in any soil all as specified and as directed by Engineer-in-Charge.

Material and labour for plain cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed.

Material and labour for broken stone or boulders hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed by Engineer-in-Charge.

Material and labour for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed by Engineer-in-Charge.

Material and labour for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) complete all as specified and as directed by Engineer-in-Charge.

Material and labour for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface complete all as specified and as directed by Engineer-in-Charge.

Material and labour for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed by Engineer-in-Charge.

Material and labour for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Plain Cement Concrete 1:2:4 type B1 using 20mm graded stone aggregate as in Damp Proof Course, mixed with water proofing compound complete all as specified and as directed by the Engineer-in-charge. Note: water proofing compound shall be measured & paid seprately

Supply only integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Pidilite Industries Ltd, Taloja /Super Aquacem (India) Ltd /FOSROC/Siko/Dr Fixit

Material and labour for Pre-cast cement concrete block masonry 1:3:6 type C1, (using 20mm graded stone aqggregate), with solid blocks, exceeding 10 cm in width and setting in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick cement concrete (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection and finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75mm thick Plain Cement Concrete 1:4:8 type D2, using 40mm graded stone aggregate as in sub base of flooring/ hard standing/path and finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for coloured glazed ceramic tiles of size 300mm x 200mm x 7 mm thick, on vertical surfaces etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for rendering 15 mm thick in cement mortar 1:4 on concrete / brick masonry surfaces, mixed with water proofing compound and and finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note: water proofing compound shall be measured & paid separately

Material and labour for two coats of Cement base paint including preparation of new plastered wall surfaces. etc complete all as specified and directed. Make- Super Snowcem/ Duracem/ Aquacem/ Shalimar/ Berger

Supply and fix aluminium anodised barrel tower bolt of extruded section size 200mm complete all as specified and as directed by Engineer-in-Charge. Make : Classic/ Shalimar/ CLIF/ARGET

Supply and fix mild steel TMT bars, 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Supply and fix mild steel TMT bars, 5 to 10mm dia in stirrups, spacers and binder cut to length bent to shape required inch cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for fair finished surface of concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) as in foundation, footing, bases of columns, raft and raft beams, plinth beams, mass concrete and similar work etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Formwork to sides of square/rectangular pillars, posts, struts, piers, columns and stanchions for fair finish surface of concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) as in columns, pillars, piers, posts and struts etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for fair finish surface of concrete complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Formwork to soffits of suspended slabs such as floor slabs, roof slabs, landings and similar work not exceeding 200mm thick (horinzontal or sloping) for fair finish surface of concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like etc complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for Formwork to chullah hoods, chajjas, trough and the like including edges for fair finish surface of concrete complete all as specified and as directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) as in chullah hoods, chajjas, trough and the like etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for reinforced cement concrete M-30 (design mix) (using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by Engineer-in-Charge.

Supply and fix mild steel tubing medium grade 15mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix mild steel tubing medium grade 20mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix mild steel tubing medium grade 25mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Supply and fix gun metal globe/ gate valve, 20mm bore, with iron wheel head, screwed both ends for iron pipes, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Leader/Zoloto/Seiko/Sant/ Essco/Prayag

Supply and fix ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed of 20 mm bore complete all as specified and as directed by Engineer-in-Charge Make : Leader/Zoloto/Seiko/Sant/GEM

Supply and fix stop valve/push cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix vitreous china bowl urinal, flat back, size 465 x 355x 265 mm white (minimum), with grating and urinal for discharge pipe, waste pipe complete including providing and fixing plugs, bedding urinal against wall in CM securing urinal to plugs with and including 60mm long brass screws, pointing around, fixing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and as directed by Engineer-in-Charge. Make: Cera/Hindustan/Parryware/Jaguar/Hindware /Johnson

Supply and fix waste pipe of PVC. 32 mm dia, for WHB/ urinal complete all as specified and as directed by Engineer-in-Charge.

Supply and fix stop valve/angle cock, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 15mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix PVC connection, 15 mm size 600 mm long, both end socket fix and PTMT check nuts complete all as specified and as directed by Engineer-in-Charge. Make : Jaypee/GMP/Neta/Zoloto/Prayag/Symet

Supply and fix PVC (SWR) floor trap outlet dia 75mm, plain with gratings including jointing etc complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Finolex / Supreme/Astral

Supply and fix aluminium anodised towel rail, 20mm dia, D type, 60cm long, between flanges complete all as specified and as directed by Engineer-in-Charge.

Supply and fix pillar taps fancy type cast copper alloy with capstan head, chromium plated, screwed down high pressure, with or without lettered ‘hot’ or ‘cold’ with long screwed shanks and fly nuts, screwed for iron pipes, 15mm bore complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix PVC (SWR) Single socketed rain water pipes/soil waste pipes with rubber ring joints 75mm dia , fixed to wall including scaffolding and upto any height complete all as specified and directed. Make: Finolex/Prince/Kisan/Supreme/Astral

Supply and fix PVC (SWR) Single socketed rain water pipes/soil waste pipes with rubber ring joints 110mm dia , fixed to wall including scaffolding and upto any height complete all as specified and directed. Make: Finolex/Prince/Kisan/Supreme/Astral

Supply and fix PVC (SWR) bends any radius, 75mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex/Astral

Supply and fix PVC (SWR) vent cowl 110 mm dia complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex/Astral

Supply and fix 15mm bore bib taps, fancy type, chromium plated, cast copper alloy, with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed by Engineer-in-Charge. Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix PVC valveless, syphonic action type low level flushing cistern 10 ltr capacity white with inlet ball valve, float and handle including brackets, including flush pipe of polyethylene of low or high density or PVC 32mm dia including connection to pipe and fixing of chains and pull or lever complete all as specified and as directed. Make : Slimline/Commander/Hindustan.

Supply and fix flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete all as specified and as directed by Engineer-in-Charge.

Supply and fix vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) with PVC seat cover, chromium plated hinges & nuts including ‘P’ trap / 'S' trap, connection to drain flushing pipe, antisyphonage pipe complete all as specified and as directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware/ Johnson

Supply and fix vitreous china wash hand basin, white, flat back of size 450 mm x 300 mm excluding taps, waste pipe, chain and plug and porcelain stopper including brackets, chromium plated waste coupling, waste fitting etc, cutting for and pinning in ends of brackets, connecting to supply and waste pipe complete as specified and directed. Make : Cera/Hindustan/Parryware/Jaguar/Hindware /Johnson

Supply and fix rotational moulded polyethylene water storage tank (Cylindrical vertical with closed stop), HDPE, triple layered with ISI marked of 500 ltrs capacity with inlet & outlet connections, tank nipple, bends, sockets etc, hoisted and fixed in position complete all as specified and as directed by Engineer-in-Charge. Make : Sintex/Polycon/infra/Rotex

Supply only Bitumen, blown type, 85/25 grade as in sealing compound for plinth protection complete all as specified and as directed by Engineer-in-Charge.

Material & Labour for applying evenly a tack coat of in dustrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and as directed by Engineer-in-Charge.

Material and labour for APP modified waterproofing treatment to slab & parapet wall with following specification including brushing off the surface to receive the treatment obtain the required surface complete as directed by Engineer-in-Charge :- (a) Applying oil bound bituminous primer @ 0.4 lit/Sqm of density 0.87-0.89Kg/lit of 250C on the prepared dry roof surface. (b) Laying 4mm thick APP membrane weight not less than 3.60 KILOGRAM per sqm by torch application with minimum 10cm side lap and 15cm end lap. The laying of membrane shall be got done through an authorized applicator of manufacturer of APP membrane. (c) Over the membrane provide a coat of solar reflective bituminous aluminium paint @ 0.15 Kg/Sqm prescribed by manufacturer complete all as specified. Make of APP Membrane- (a) STP Ltd (b) Texsa India Ltd (c) IWL Ltd (d) TIKI TECH.

Supply and fix 15 micron coloured aluminium anodised grill of design No DG-101 of size 7 x 4.5mm thick, fixed with channel of size 38mm x 12mm x 1.3mm, cut to required size/shape, and fixed in position with and including aluminium beading and frame complete all as specified and as directed by Engineer-in-Charge. Make: DECOGRILL of Associated group or equivalent make as approved by GE

Supply and fix 4.0mm thick black glass, ordinary quality in square exceeding 0.5 Sqm in each pane, fixed in aluminium windows complete all as specified and as directed by Engineer-in-Charge. Make : Modiguard/Atul/Kohinoor/Swastik/Saint Gobain

Material and labour for marble work 18 to 20 mm thick machine cut, table rubbed and polished, bedded and jointed as in steps, jambs, pillar, window cills, cooking platform and like bedded and jointed with grey cement slurry and pointing in white cement 1:2 using marble dust with admixture of pigment to match including 10mm thick screed bed/recdering coat in cement mortar 1:4 etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for plain cement concrete 1:2.:4 type B-1 (using 20mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, holstring courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, kerbs, water troughs, bed plates, concrete block for hold fast etc and the like including necessary form work for fair finished surfaces including weathering, slightly rounded or chamfered angles and throating, as directed etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete 1:3:6 type C-2 using 40 mm graded stone aggregate as in surface channels and drains, benching, haunching etc. complete all as specified and as directed.

Material and labour reinforced concrete pipes 150mm bore, class NP-2, laid and jointed in CM (1:2) with spun yarn complete with collars all as specified and as directed by Engineer-in-Charge. Make : Indian hume pipes/ Everest/ Himalaya/ Thuluvananikal Pipes

Material and labour for cement concrete 1:3:6, type C2 (using 40mm graded stone aggregate), as bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in, bore of pipe 150mm bore of pipe complete all as specified and as directed by Engineer-in-Charge

Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete with using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and as directed.

Add or deduct in item No 122 above but for each 25mm girth or part thereof over or under 30cm girth complete all as specified and as directed by Engineer-in-Charge

Material and labour for rendering on concrete / brick masonry surfaces, 15 mm thick in two coats of 10mm thick in cement mortar 1:6 & 5 mm thick in cement mortar 1:4 , mixed with water proofing compound in 2nd coat only and finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note: water proofing compound shall be measured & paid separately

Supply and fix mild steel TMT bars, 6 to 8mm dia cut to length bent to shape required including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Material and labour for precast reinforced cement concrete with nominal mix, 1:2:4, type B1 using 20mm graded stone aggregate for manhole /drain covers/ cover slabs and similar articles with plain faces set in CM 1:4 finishing the exposed faces even and smooth using extra cement including demolition of existing un serviceable RCC covers and removing debries out side MD land complete all as specified and as directed by Engineer-in-Charge Note- Reinforcement shall be measured and paid separately

Supply and fix framed work confirming to Fe-410- W (Gde E-250) quality B as in doors or gates of angle or other section with gusset plate, rails, braces etc complete, drilled for fixing of steel sheeting or other covering,doors etc to be prepared for hanging or sliding with and incl. either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and guaging also fastening and fixing complete all as specified and as directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed by Engineer-in-Charge

Material and labour for cutting into existing manholes for 150/200mm internal dia of pipes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B1, smooth finished and reforming benching as required complete all as specified and as directed by Engineer-in-Charge.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in deep for foundation, laying pipes, laying UG cables etc or for shaft, walls, manholes, pier holes etc not exceeding 10 sqm on plan and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge

All as per item No. 127 above but depth exceeding 1.50M but not exceeding 3.00m

Supply and fix galvanised iron pipe, light grade, 40mm bore for cable protection on wall, trenches, road crossings etc. with suitable size of GI saddle, wherever necessary complete all as specified and as directed by Engineer-in-Charge. Make: TATA/SWASTIK/JINDAL/Bharat Steel tube/ZENITH/Indian Tube Company

Supply and Lay LT UG XLPE insulated, heavy duty, 1100 V grade electric cable with aluminium conductor, served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of size 10 sqmm x 2 core, laid in trenches or passing through pipe, making all connections with and including provision of necessary glands, lugs, bushing etc as required complete all as specified and as directed by Engineer-in-Charge. Note : Earthwork excavation, pipe for cable protection shall be measured and paid separately in their respective items Make: Cable Corporation of India (CCI)/ Asian Cable Co, Chattisgarh/ Finolex/ Polycab/ Gloster/Universal/ RPG Cables Ltd , Thane/ Havells India Ltd/ RR Kabel/ KEI Industries Ltd(KEI)

Material & Labour for sand filling in trenches with clean dry fine sand unwashed including gently punning around cables complete all as specified and as directed by Engineer-in-Charge

Supplying and laying old size bricks, common burnt clay building bricks, sub class 'B', designation 75, laid in trenches over sand for cable protection complete all as specified and as directed by Engineer-in-Charge

Supply and fix mild steel tubing medium grade 20mm, galvanized iron with all fittings such as Tees, elbows, sockets, bends, unions, short pieces, nipples, brass nuts and diminishing pieces complete all as per IS 1239, laid in trenches complete all as specified and as directed by Engineer-in-Charge. Make: Tata / Jindal / Surya Prakash / Zenith

Cutting existing steel tubing for alterations or additions of size 40/50mm bore, screwing (Each cut to be measured) complete all as specified and as directed by Engineer-in-Charge.

Supply and fix stop valve, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipes or for unions of 20mm bore complete all as specified and directed by Engineer-in-Charge Make : Jaquar (Essco)/Prayag / Seiko

Supply and fix gun metal globe/ gate valve, 50mm bore, with iron wheel head, screwed both ends for iron pipes, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Leader/Zoloto/Seiko/Sant/ Essco/Prayag

Material and labour for rendering 10 mm thick in cement mortar 1:6 on concrete / brick masonry surfaces and finished even and smooth with 1.5mm thick wall care putty complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for rendering 5 mm thick in cement mortar 1:3 on concrete / brick masonry surfaces and finished even and smooth with 1.5mm thick wall care putty complete all as specified and as directed by Engineer-in-Charge. Make: Asian Paints / Nerolac Paints /Jenson & Nicholson / Shalimar Paints / JK wall care putty

Material and labour for preparation of newly plastered ceiling surfaces and applying two coats of oil bound distemper with roller over a coat of alkali resistant wall primer etc complete all as specified and directed by Engineer in Charge. Make: Asian Paints (Tractor) / Nerolac Paints /Jenson & NIcholson / Shalimar Paints

Material and labour for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc., set and jointed in neat cement slurry and pointed in coloured cement to match over and including screed bed of 15mm thick in cement mortar 1:6 including scarifying the floor complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Material and labour for light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, on vertical surfaces etc, set and jointed in neat cement slurry and pointed in coloured cement to match including 10mm thick backing coat in cement mortar 1:4 complete all as specified and as directed by Engineer-in-Charge. Make: M/s H R Johnson / M/s Kajaria / M/s Somany Tiles Ltd / M/s Orient bell / M/s RAK tiles

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of size 150mm bore complete all as specified and as directed by Engineer-in-Charge. Note- Earth work shall be measured and paid separately.

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of size 200mm bore complete all as specified and as directed by Engineer-in-Charge. Note- Earth work shall be measured and paid separately.

Demolition of reinforced cement concrete of manhole cover (reinforcement cut as required to facilitate demolition) and removing concrete debris and depositing outside MD land complete all as specified and as directed by Engineer-in-Charge

Demolition of brickwork /stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Removing manhole cover of any type / size / thickness and cleaning manhole chamber of any shape & size not exceeding 1.50m deep by removing sludge / mud frome manhole and removing of debris outside MD land complete all as specified and as directed by Engineer-in-Charge

Supply and fix PVC (SWR) single socketed rain water/ soil waste pipes, type B, with rubber ring joints, 110mm dia, laid in trenches or in floors complete all as specified and as directed by Engineer-in-Charge Make: Finolex/Prince/Kisan/Supreme/Astral

Surface dressing n exc 15cm in hard dense soil complete all as specified and as directed by Engineer-in-Charge

Site clearance including removing all grown vegetation, trees, shrubs, plants etc complete all as specified and as directed by Engineer-in-Charge

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and as directed by Engineer-in-Charge.

Rough excavation not exceeding 1.5m deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

Rough excavation exceeding 1.5m deep & not exceeding 3.0m deep and getting out in soft/loose soil complete all as specified and as directed by Engineer-in-Charge.

Rough excavation not exceeding 1.5m deep and getting out in hard/dense soil complete all as specified and as directed by Engineer-in-Charge.

Rough excavation exceeding 1.5m deep & not exceeding 3.0m deep and getting out in hard/dense soil complete all as specified and as directed by Engineer-in-Charge.

Material and labour reinforced concrete pipes 200mm bore, class NP-2, laid and jointed in CM (1:2) with spun yarn complete with collars all as specified and as directed by Engineer-in-Charge. Make : Indian hume pipes/ Everest/ Himalaya/ Thuluvananikal Pipes

Material and labour for brick work with sub class 'B' bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for plain cement concrete 1:2:4 type B-2 using 40 mm graded stone aggregate in foundation, filling and mass concrete complete all as specified and directed.

Demolition of cement concrete unreinforced of any description and in any position, not otherwise specifically provided for including removing debris out side MD land complete all as specified and directed by Engineer-in-Charge.

Material and labour for 100mm thick Plain Cement Concrete 1:4:8 type D2, using 40mm graded stone aggregate as in hard standing/path and finished even and fair without using extra cement etc complete all as specified and as directed by Engineer-in-Charge

Material and labour for 100mm thick Plain Cement Concrete 1:2.:4 type B2, using 40mm graded stone aggregate as in hard standing/path and finished even and smooth without using extra cement etc complete all as specified and as directed by Engineer-in-Charge

Material and labour for plain cement concrete 1:2:4, type B-2 using 40 mm graded stone aggregate as in surface channels and drains, benching, haunching etc. including necessary formwork for fair finished surfaces complete all as specified and as directed by Engineer-in-Charge

Material and labour for cement concrete 1:3:6, type C2 (using 40mm graded stone aggregate), as bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in, bore of pipe 200mm bore of pipe complete all as specified and as directed by Engineer-in-Charge

Material and labour for reinforced cement concrete, 1:2:4 type B-1 using 20 mm graded stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs, shelves and the like etc complete all as specified and as directed by Engineer-in-Charge.

Systematically cleaning mud / sludge from the drain of any size and depth including all precautionary and safety measures as required and removing the debris out side MD land complete all as specified and as directed by Engr-in-Charge.

Supply and fix in repairs PVC (SWR) single socketed rain water/soil waste pipes, type B, with rubber ring joints, 75mm dia, fixed to walls or in weep holes complete all as specified and as directed by Engineer-in-Charge. Make : Prince / Supreme / Finolex/astral

Supply and fix in repairs PVC (SWR) bends any radius with access door, 75mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex/astral

Supply and fix in repairs PVC (SWR) bends any radius with access door, 110mm dia. complete all as specified and as directed by Engineer-in-Charge Make : Prince / Supreme / Finolex/astral

Material & Labour for Hand packing using broken stone or boulders (any thickness) at back of walls over arches etc. and raising (or lowering) to the required level complete all as specified and as directed by Engr-in-Charge

Supply & Fix in repairs salt glazed stoneware gully traps, square/rounded mouthed type ' P 'of size 150 x 150mm including grating and setting in PCC 1:2:4 type B1 and jointing to drain with CM (1:1) complete all as specified and as directed by Engr-in-Charge

Supply of PWTS series Polyethylene Tank which is an advance version of Septlc Tank with capacity of 5000 lit per day, diameter of 2070 mm and height of 2280 mm, tank has two zone, first is septic zone where sludge is stabilized by anaerobic digestion, second zone is pall ring media zone having surface area of 190 Sq.mt/ Cum and retain micro-organism long enough to digest the organic waste which results in 60-70% of BOD reduction from final out let. It is provided with inlet & oulet pipe of 100 mm dia., vent pipe of 50 mm dia, lnternal piping, manhole cover of 400 mm dla-1No. complete all as specified and as directed by Engr-in-Charge Make- Sintex or equivalent as approved by GE Note : The unit quoted rate shall be deemed to include for following: (i) Excavation in any type of soil , RFR, removal of excavated soil and depositing the same outside the MD land. (ii) Size of excavation pit shall be approximately 600mm from external wall of the tank for work space. Depth of the pit should be decided based on position of inlet and outlet with required gradient and disposal point plus 150mm extra for bedding as directed by Engineer-in-Charge . (iii) Contractor is responsible for lowering the tank properly and positioning it in the pit vertically, centrally positioned, correctly aligned and leveled using a spirit level. The outlet pipe should face the soak pit and inlet pipe swivels, ensuring a straight connection and tank shall be checked for any leakage after installation and any damage during installation shall be borne by contractor.

Material and labour for construction of soak pit of bore 1.20 metre dia x 1.5 metre deep including necessary excavation in any type of soil with foundation of PCC 1:3:6 Type C2, honey combed and solid in M-25 concrete incl. intercepting chambers, screen chambers brick work in CM 1:4, RCC cover slab M-25 filling with brick bats complete all as shown on drawing, complete all as specified and as directed by Engr-in-Charge. DRG NO. CWE BOMBAY TD/8811 Sheet no .1/1 Dated 19 Jul 88 revised date 15/12/12

Material and labour for Point wiring for complete with PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor conforming to IS-694, 1.5sqmm (nominal area) drawn through and including non metallic PVC conduit 20mm dia (ISI marked) and accessories laid on surface of wall/roof with sunken type pressed steel/welded terminal boxes made out of 1.2mm mild steel sheet, modular cover plates for mounting of switches, socket outlets, regulators etc., including provision of PVC insulated FRLS cable 1100 volts grade with multi stranded copper conductor 1.5sqmm as earth continuity conductor and connecting to common earth dolly for One light controlled by one, one way switch complete all as specified and as directed by Engineer-in-Charge. (i) Red wire use for live connection, black wire use for neutral and green wire use for earthing also individual circuit form DB. for each board. Note: Serviceable switch / socket outlet shall be reused. Make of Cable-Plaza, Finolex, Havells, Polycab Make of PVC conduit-Anchor, Modi, Pressfit, Precision, Astral, Panasonic Anchor, Polycab, Presto Plast, Supreme

All as per item No.172 above but for One exhaust fan controlled by one, one way switch

Supply and fix Modular type switch, single pole, one way, 6 Amps, One Module, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T / Honeywell/ Crabtree/ leader

Supply and fix Ceiling rose, surface type Bakelite, three terminal PVC/ polycarbonate isolated body, 65x32mm, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make: Anchor / Legrand / L&T / Honeywell/ Crabtree/ leader

Supply and fix MCB distribution board SPN, 240 Volts, 4 ways powder coated, CRCA steel sheet constructed as per IS:8623, degree of protectrion IP 43-IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral bus bar, earth bar, DIN bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required complete all as specified and as directed by Engineer-in-Charge. Make: Havells / Legrand / L&T

Supply and fix LED batten (1.2m) made of aluminium housing with a PC glossy diffuser duly prewired connection having a nominal system, lumen output of 2000 lumens at a minimum system efficiency of 100+ lumens per watt and total power consumption not less than 20 watt incl. driver with rated system life time of 40000 burning hours at L70 and should have a colour temperature of B196eng-in-charge. Make:- Phillips cat part no. BNO21C LED20S PSU CW GR S2 or Equivalent of Havells/ Bajaj

Supply and fix MCB SP, 6 Amps to 32 Amps, 240 volts,10 KA 'C' Series, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider//BENTEC

Supply and fix MCB DP, 32 Amps, 240 volts,10 KA 'C' Series, ISI marked complete all as specified and as directed by Engineer-in-Charge. Make : Legrand / L&T / Havells / ABB / Siemens / Schneider//BENTEC

Supply & Fix air ventilation fan 250mm in toilet in rectangular in shape, PVC body, white colour, 230V including louver shutter complete all as specified and as directed by Eng-in-charge. Make: Havells/bajaj/wipro

Cutting chases with dust free cutting machine, pinning in, making good the disturbed surface of wall/ceiling and pointing in cement mortar 1:3 to cutting chases for concealed conduit wiring etc. and making good etc, not exceeding 10 cm girth complete all as specified and as directed by Eng-in-charge

Note: Deduct Credit for demolished / dismantled material of Rs. (-) 56855.00 (Minus) as listed in Schedule of Credit. Tenderers will not quote against this item being a tentative amount to be considered to arrive at the 'Contract Sum'

S.N Enterprises

MAHESH ENTERPRISES

joshua construction