Mother and Child Hospital (500 bedded) at Gauhati Medical College and Hospital, Guwahati under SOPD-ODS for the FY 2019-2020 (Including internal electrical works)

Amount

Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. Up to a depth of 2.00 M below the existing ground level. In ordinary soil

Earth work in excavation in slushy/ marshy soil, decomposed organic matter mixed with brickbats, broken glass panes, broken earthen pots etc. removal of stumps and other deleterious matter in the proposed building site including constant water pumping for bailing out water as directed including return filling and ramming after completion of work with good quality earth (measurement will be on the basis of profile or section measurement).

Extra over item no.1.1(A) above for each 1 m depth or part thereof beyond the initial depth of 2m. (From 2 m to 3 m)

Extra over item no.1.1(A) above for each 1 m depth or part thereof beyond the initial depth of 2m. (From 3 m to 4 m)

Extra over item no.1.1(A) above for each 1 m depth or part thereof beyond the initial depth of 2m. (From 4 m to 5 m)

Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. Stone soling of thickness 150mm.

Earth/ sand filling in plinth in layers not more than 150mm thick including necessary carriage, watering, ramming etc. complete as directed and specified including payment of land compensation, forest royalty, sales tax and other duties and taxes as may be necessary. (c) With river sand or silt (predominantly non plastic) by truck carriage including loading and unloading.

Raising low site around the building with approved soil obtained from outside by truck carriage including breaking clods, dressing etc. complete including paying necessary forest royelty, sales tax, land compensation, municipal gate fees, if any monopoly duty etc. (profile measurement to be taken and 12.5% deduction for shrinkage to be made from total quantity) etc. complete as directed and specified. (a) Within Guwahati city only

Plain cement concrete works with coarse aggregate of sizes 13 mm to 32 mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, curing complete (Shuttering where necessary shall be measured and paid saperately). In prop 1 cement :4 Sand :8 coarse aggreget by volume

Providing form work of ordinary timber planking so as to give rough finish including centering , shuttering, struting and propping etc. height of propping and centering below supporting floor to ceiling not exceeding 4.0m & removal of the same for in situ reinforced concrete and plain concrete work in: Foundations, footings, bases of columns, pile cap, raft and mass concrete work etc. Using 25 mm thick plank

Columns, Pillars, Posts and Struts Square, Rectangular, polygonal in plan or any shape like Tee/L etc. having plane vertical face.Using 25 mm thick plank Basement

Gr. Floor to Terrace

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Sides and soffits of Beams, beam haunchings, cantilever girders, bressumers, lintel and horizontel ties. For depth not exceeding 1.0 M. Using 25 mm thick plank Basement floor

Gr. Floor to Terrace

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas, balconiess and the like. Floor etc. above 200 mm in thickness. Using 25 mm thick plank Basement Roof

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas, balconiess and the like. Floor etc. above 200 mm in thickness. Using 25 mm thick plank. Gr. Floor to Terrace

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Vertical surfaces such as walls (any thickness), parapet walls, partition, walls of septic tank, inspection pit and the like including attached pilasters, butresses, plinth and string courses. Using 25 mm thick plank Basement Floor

Staircase with sloping or stepped or stepped soffits including riser and stringers but excluding landing. Using 38 mm thick plank. Basement Floor

Gr. Floor to Terrace

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item above 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Extra for each subsequent 1.0 M height or part there of beyond the initial height of 4.0 M as mentioned in item no. 3.1.1

Providing form work of ordinary timber planking and removal of the same in edge of slab and breaks in floors and walls etc. of in situ reinforced concrete work upto first floor level. Thickness not exceeding 200 mm Basement Floor

Gr. Floor to Terrace

Extra for each subsequent floor or part thereof above the first floor level as mentioned in item no. 3.1.3(a). 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Supplying, fitting and fixing in position reinforcement bars confirming to relevant I.S. Code for R.C.C. work/ R.B. walling including straigtening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level.) From primary Producer: TATA/ SAIL/ Jindal Steel/ Shyam Steel/ RINL TMT Corrosion resistance steel (CRS) reinforecement bars Foundation

Gr. Floor to Terace Floor

Extra over item for each subsequent floor or part thereof above first floor level. 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concerete Pump. In Sub Structure. Using admixture, plasticizer etc. M25 grade concrete

Providing and laying plain/reinforced cement croncrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately).Using Batching Plant/ RMC/ Truck mounted batching plant including Transit Mixer and Concerete Pump. In Super Structure. Using admixture, plasticizer etc. M25 grade concrete Gr. Floor to Terrace

M30 FOR COLUMNS

Extra over item above for each subsquent floor or part thereof above 1st floor level. 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Providing cast in-situ machine driven reinforced cement concrete piles of required bore-diameter, bulb diameter, lengths and with reinforcement as per specifications and drawings including using of Bentonite solution. (Reinforcement to be measured and paid seperately as per item no. 21.4.1). UNIFORM PILE .Concrete Grade M25 Pile dia 600 mm

PILE TESTS Routine test for test loading to 1.5 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Initial test for test loading to 2 times the specified safe working load including construction of any test pile cap and dismantling the same after completion of test. (Rate for Safe working Load)

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. In Sub-structure upto plinth level including dewatering if necessary. In proportion 1:6

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. In super structure above plinth level upto 1st floor level. In proportion 1:6 Basement Floor

Gr. Floor To Terace Floor

Extra over item above for brick work in each subsquent floor or part thereof above 1st floor level. 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

112 mm thick reiforced brick wall in prop 1:5 reinforced with two lines of M.S. rod/ Tor Steel as specified embeded in 38 mm thick concrete course in prop 1:2:4 with coarse agg. 12 mm down at every fourth courses embeded with protruding rod in column including curing etc. complete as directed (M.S. rod/ Tor steel shall be measured and paid separately) in super structure up to 1st floor level. Gr. Floor To Terace Floor

Extra for brick walling for each subsquent floor or part thereof above 1st floor level. 112 mm thick brick/ R.B. wall 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Superlight weight Autoclaved Aerated concrete Block work using Grade-I AAC Block of size 625x240mm of different thickness of compresive strength 40 kg/cm2 having dry density 550 to 650 kg/cum conforming to IS : 2185 pt-3 or pt-4 in cement mortar of Prop 1:4 including racking out joints and curing complete as specified & Directed.(Protruding rod is to be provided at every 3 course interval and will be measured and paid seperately) (I) For 225 mm Thick Wall In Sub-Structure below plinth level including dewatering if necessary (Basement Floor)

Superlight weight Autoclaved Aerated concrete Block work using Grade-I AAC Block of size 625x240mm of different thickness of compresive strength 40 kg/cm2 having dry density 550 to 650 kg/cum conforming to IS : 2185 pt-3 or pt-4 in cement mortar of Prop 1:4 including racking out joints and curing complete as specified & Directed.(Protruding rod is to be provided at every 3 course interval and will be measured and paid seperately) (IIa) For 225 mm Thick Wall In Super-Structure above plinth level up to 1st Floor level. (Gr. Floor To Terace Floor)

Extra for AAC block walling for each subsquent floor or part thereof above 1st floor level. (i) 225 mm thick wall 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Superlight weight Autoclaved Aerated concrete Block work using Grade-I AAC Block of size 625x240mm of different thickness of compresive strength 40 kg/cm2 having dry density 550 to 650 kg/cum conforming to IS : 2185 pt-3 or pt-4 in cement mortar of Prop 1:4 including racking out joints and curing complete as specified & Directed.(Protruding rod is to be provided at every 3 course interval and will be measured and paid seperately) (IIc) For 125 mm Thick Wall In Super-Structure above plinth level up to 1st Floor level. (Gr. Floor To Terace Floor)

Extra for AAC block walling for each subsquent floor or part thereof above 1st floor level. (i) 125 mm thick wall 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Providing and fixing flush door shutters solid core construction with frame of 1st class hard wood with cross band and face veneered ply wood face panels conforming to relevent I.S code including oxidised iron butt hinges (100mm x 75mm x 3.5mm) 6 nos with necessary wood screws. Decorative type and block board core. 40 mm thick.

Extra for providing lapping with 1st class Teak wood battens of 25mm minimum depth on all edges of the shutters.

Supplying, fitting, fixing Stainless Steel fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished )

Supplying, fitting, fixing Stainless Steel fittings of approved make, resonably smooth, free from sharp edges and corners, flaws and other defects and with counter sunk holes for screws including necessary c.p. brass screws etc. complete.( bright natural matt & satin finished ) Tower Bolt 150mm x 10mm

Providing and fixing stainless steel (Grade 304) railing made of hallow tubes, chanells, plates etc. including welding grinding buffing, polising and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i.e. fixing railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in charge.(for payment purpose only weight of stainless steel members shall be considered excluding fixing assessories such as nuts, bolts, fasteners etc.)

Providing and fixing rolling shutters of approved make made of 80mm wide M.S. laths interlocked together through their entire length and jointed together at the ends by end-locks mounted on specially designed pipe shaft with bracket plates, guide channels and arrangements for inside and outside locking with push-pull operation complete including cost of wire, spring and hood cover for the shutters.

40 mm thick cement concrete floor consisting of 25 mm under layer of cement concrete in prop 1:3:6 (1cement : 3coarse sand : 6 coarse aggregate of 12.5 mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1cement : 1coarse sand : 2 coarse aggregate of 10 mm and down) finished with a floating coast of neat cement finish using cement slurry for bond @ 2.75 kg. per sqm. of floor area, wearing layer is to be laid in panels including curing complete as directed.

Cement plaster skirting with cement mortar in prop. 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. 20 mm thick

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). Delux range Somany/ Orient/Nitco/Qutone Make. Of size 300mmx300mm and above

Providing polished Ceramic wall Tiles of approved quality, size, shape and thickness not less than 8 mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 Cement: 3 Coarse sand), including cutting where necessary finished with flush pointing with fix-A Tile (Choksey/ Sika/ Pedelite/ Rouf/ White cement slurry) mixed with approved pigment to match the shade of tiles complete at all levels as specified and directed (coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Wall means both interior and exterior walls). Delux Range (Somany/ Orient/ Nitco/ Varmora Make). of size 300mm x 450mm and above

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). Of size 600mmx600mm and above

Providing VITRIFIED floor tiles of approved quality of specified size, shape and thickness not less than 18mm on floors, skirtings, risers and treads of steps over 15 mm thick base of cement mortar in prop. 1:3 (1 cement : 3 coarse sand ) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/Sika/Pedelite/Rouf) / white cement slurry mixed with approved pigment to match shade of tiles, mixed with approved pigment to match the shade of the tiles, complete at all levels as specified and directed. (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). Delux range -Somany/ Orient/Nitco /Varmora/VITA/ Marbito/ Make. Of size 1000mmx1000mm and above

Providing Polished vitrified wall tiles of approved quality of specified size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10 mm thick in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)/ White cement slurry mixed with approved pigment to match the shade of tiles complete at all levels as specified and directed (coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). Of size 300mm x 600mm and above

Kota stone slab flooring of 18 mm thick over 20 mm thick base of cement mortar 1 : 6 (1 cement : 6 coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete. 550mm x 550mm

Kota stone slab of 18 mm thick in riser of steps, skirting, dado and pillars laid with 10 mm thick cement plaster 1 : 3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete. 550mm x 550mm

Providing Polished Granite Slab of approved quality, size, shape and thickness not less than 18 mm on floors, skirtings, treads and risers of steps over cement mortar bed 15 mm thick in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)/ White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (Cement plastering to be measured and paid separatly) (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). Delux Quality- With Fix-A-Tile (Choksey/ Sika/ Pedelite/ Rouf)

Providing, fitting and fixing Laminated abrasion resisitant wooden flooring from Uniproducts (India) Ltd. of thickness not less than 8.2 mm laid on existing concrete floor with under layer of approved transparent polythene and foam sheet to make the floor surface even and sound free complete as directed and directed. Unitex AC4 Brand

10 mm cement plaster in single coat on fair side of brick/concrete walls for interior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed. In cement mortar 1:6 Basent. Floor

Gr. Floor to Terrace Floor

Extra over item above for interior plastering above 1st floor level for every additional floor or part there of including curing complete as directed. (a) On single coat plaster. 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

15 mm cement plaster in single coat on rough side of single or half brick walls for interior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed.In cement mortar 1:6 Basent. Floor

Gr. Floor to Terrace Floor

Extra over item above for interior plastering above 1st floor level for every additional floor or part there of including curing complete as directed. (a) On single coat plaster. 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

15 mm cement plaster in single coat on rough side of single or half brick walls for exterior plastering upto 1st floor level including aries or rounded angles not exceeding 80mm grith and finished even and smooth including curing complete as directed. In cement mortar 1:6 Gr. Floor to Terrace Floor

Extra over item above for exterior plastering over wall for every additional floor or part there of beyond 1st floor level including curing complete as directed. (a) On single coat plaster. 1st Floor

2nd Floor

3rd Floor

4th Floor

5th Floor

6th Floor

7th Floor

8th Floor/ Terrace

Applying one coat of cement primer of approve brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and other foreign matter and including preparing the surface even and sand papered smooth.

Providing two coats of Birla White Wall Care Putty (Water Resistance White Cement based putty for concrete/ mortar walls and ceiling both internal and external) after removing all loosely adhering material from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm). Thickness = 1.5 mm thick

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. Acrylic Emulsion Paint approved brand and manufacture (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac).

Painting two coats (Including priming coat) on new steel and metal surface surface with enamel paint of approved brand and manufactures (Asian paint/ Berger paint/ ICI paint/ J&N paint/ Narolac) to give an even shade including cleaning the surfaces of all dirt, dust and other foreign matter. Surfaces over 100 mm in width or girth. High gloss (Asian paint/ Berger paint/ ICI paint/ J&N paint / Nerolec).

Finishing old/ new wall with water proofing weather coat smooth anti-fungal premium textured exterior finish of Sandex Matt brand of Snowcem India Ltd. of required shade after clering and clearing the surfaces etc.including scaffolding complete as directed at all levels (two coats).

ALUMINIUM PARITION WITH DOORS Providing, fitting and fixing anodised aluminium framed glazed doors with partition walls partly glass and partly prelaminated board with anodised aluminium frame made of 100mm x 43mm x 2mm sections of approved brand with doors style of size 81mm x 43mm x 2mm, top rails 46mm x 43mm x 2mm, lock rails 81mm x 43mm x 2mm, fitting with glazing clip, special rubber type gusket complete including hydraulic floor spring pivot aluminium door handle lock angles cleat etc. complete as directed by the department at all levels. 6mm thick glass panes and 12mm prelaminated board

ALUMINIUM SLIDING DOOR Providing, fitting and fixing coloured anodised aluminium sliding glazed doors with anodised aluminium frames made of 100mm x 45mm x 2mm section of approved brand with door style of size 81mm x 45mm x 2mm, top rails 55mm x 45mm x 2mm, lock rails 81mm x 45mm x 2mm, fitted with glazing clip, special type rubber gasket complete including roller, tower bolt, aluminium door handle, lock, angles, cleat etc. complete as specified and directed by the department at all levels. 6mm clear glass

Providing and fixing of leak proof,fire retardant and Uv resistant skylighting galzing with Lexan polycarbonate sheet fixed with specially designed Domal management system confirming to IS:737 alloy & temper 6063 - T6 with a UTS of 180 to 200 mpa and weight of 1.03 kg/mtr. approx with EPDM rubber gasket of specific gravity as per ISO 2781,age resistant as per ASTM - D573 hardness as per 2240 & tensile strength as per ASTM 412 including the silicon sealent GE Bayer Weathersil NY as per drawing and directed by the Engineer in charge. 10 mm thick Polycarbonate Sheet (Multiwall)

By Mechanical Transport including loading ,unloading and stacking up to 5 km

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement :3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Providing and laying in position ready mixed plain cement concrete, using fly ash and cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. Note : (1) Excess/less cement used than specified in this item is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement is to be ensured in accordance with clauses 5.2 and 5.2.1 of IS: 456 -2000 in the items of BMC and RMC. All works upto plinth level : M-10 grade plain cement concrete (cement content considered @ 220 kg/cum)

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical locations in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions.The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in-Charge. (Material shall conform to ASTM 6063). Floor Joint of 200 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning /centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall conform to ASTM 6063.). Floor Joint of 200 mm gap

Providing and fixing of expansion joint system of approved make and manufacture for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides water tight roof to roof /roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions.The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.). Floor Joint of 200 mm gap

Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately. Providing M-30 grade concrete instead of M-25 grade BMC/RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. (Area of slab upto 0.50 sqm)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade. (Area of slab over 0.50 sqm)

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Extra for fixing marble/granite stone over and above coresponding basic item, in facia and drops of width upto 150 mm with expoxy resin based (Araldite or equivalent) adhesive including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basins/kitchen sink in kitchen platform. Vanity counters and similar location in marble/granite/stone work including necessary holes for pillar taps etc. including rubbing,moulding and polishing of cut edges etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square.

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing fire resistant door frame of section 50 x 60mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per direction of Engineer-in-charge. The glass shall be clear, toughened, interlayered, non-wired fire resistant having 11 mm thickness of approved brand with 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 15 min of insulation (EI15) and having a sound reduction of 37dB and LT of 86%. Glass shall be compliant to class 2(B)2 category of Impact Resistance as per EN 12600. The glass should be manufactured in UL & TUV audited Facility and including UL-EU Certification.The maximum glazing size cannot be more than 1100 mm x 2200 mm (w x h) or 2.42 sq mts in total area. The test report for the complete system (Glazed Door or Partition) will be considered valid only if it contains the stamp and signature of the authorized signatory from the glass manufacturer. (Actual glass size is to be measured at site for payments).

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Deduct for not providing hinges in doors, windows or clerestory window shutters with : ISI marked M.S. pressed butt hinges bright finished of required size. For 2nd class teak wood and other class of wood shutters

Extra for providing ISI marked Stainless Steel butt hinges instead of M.S. pressed butt hinges bright finished of required size with necessary screws. (Shutter area to be measured).

Structural steel work riveted or bolted in built up sections, trusess and framed work, including cutting,hoisting,fixing in position and applying a priming coat of approved ateef primer all complete.

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position and applying a priming coat of approved steel primer using structural steel, etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying C.C. pavement (TRIMIX) of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge .(Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

Filling the gap in between aluminium frame & adjacent RCC/ Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-incharge complete. Upto 5mm depth and 5 mm width

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately).

Providing and laying integral cement based treatment for water . proofing on horizontal surfaces at all levels as directed by Engineer-incharge and consisting of: 1) 1st layer of 20 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement:3 coarse sand) mixed with water proofing compund conforming to IS: 12645 in the recommnded proportion. Joints sealed and grouted with cement slurry mixed with water proofing compound conforming to IS: 12645 in proportions recommended by the manufacturer. II) 2nd'c!ass layer of 25 mm thick cement mortar 1:3 (1 cement:3 coarse sand) mixed with water proofing compound in recommended proportions. Ill) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreadidng @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota sotne.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing sspecified stone slab 20 mm thick with cemm slurry mixed with water proofing compound conforming to IS: 2645 in recommended proportion with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar1:4 (1 cement:4 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge. Using rough kota stone.

Providing and mixing integral crystalline admixture for water proofing treatment to RCC structures like basement raft, retaining walls, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc. at the time of transporting of concrete into the drum of the ready-mix truck, using integral crystalline admixture @ 0.80% (minimum) to the weight of cement content per cubic meter of concrete) or higher as recommended by the manufacturer’s specification in reinforced cement concrete at site of work. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 90%, compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure. The crystalline admixture shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For vertical surface two coats @ 0.70 kg per sqm

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage. For horizontal surface one coat @1.10 kg per sqm.

Providing and Placing in position suitable PVC water stops for construction/expansion joints between two RCC memberrs and fixed to the reinforfement with binding wire before pouring concrete etc. complete. Serrated with central buld (225 mm wide, 8-11 mm thick)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of: (i) 1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming tc IS 2645 in recommended proportions.(ii) 11 nd course of 20 mm cement plaster 1:3 (1 cement:3 coarse sand)mixed with water proofing compound in recommended proportion, (iii) Illrd course of applying blown or/residual bitumen aplied hot at 1.7 kg. per sqm of area, (iv) Ivth course of 400 micron thick PVC sheet.(Overlaps at joints of PVC shet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and fixing at all height false ceiling including providing and fixing of frame work made of special sections power pressed from M.S. sheet and galvanised in accordance with zinc coating of grade 350 as per IS : 277 and consisting of angle cleats of size 25mm wide x 1.6mm thick with flanges of 22mm and 37mm at 1200mm centre to centre one flange fixed to the ceiling with dash fastener 12.5mm diax40mm long with 6mm dia bolts to the angle hangers of 25x25x0.55mm of required length, and other end of angle hanger being fixed with nut and bolts to G.I. channels 45x15x0.9mm running at the rate of 1200mm centre to centre to which the ceiling section 0.5mm thick button wedge of 80mm with tapered flanges of 26mm each having clips of 10.5mm at 450mm centre to centre shall be fixed in a direction perpendicular to G.I. channel with connecting clips made out of 2.64mm diax230mm long G.I. wire at every junction including fixing the gypsum board with ceiling section and perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450mm centre to centre with 25mm long drive-all screws @ 230mm interval including jointing and fixing to a flush finish of tapered and square edges of the board with recommended filler, jointing tapes, finisher and two coats of primer suitable for board as per manufactures specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed all complete as per drawing and specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 gsm/sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main "T" at 600mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 x mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum),including factory painted after bending and perforation,and backed with a black Glass fiber acoustical fleece.

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance > 85%, Thermal Conductivity k = 0.052 - 0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm ) comprising of main T runners of 15x32 mm of length 3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised @80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod upto 1000mm length and L-hape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘T’. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be prepainted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. With 16 mm thick beveled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications

Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). White sand stone - 30mm thick gang saw cut stone

Providing and fixing structural steel frame (for dry cladding with 30 mm thick gang saw cut with machine cut edges sand stone) on walls at all heights using M.S. square/ rectangular tube in the required pattern as per architectural drawing, including cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and embedded in brick wall with cement concrete block 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of necessary centring and shuttering and with approved expansion hold fasteners on CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be welded to the frame work to support stone cladding, the steel work will be given a priming coat of Zinc primer as approved by Engineerin-charge and painted with two or more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the Engineer-in-charge for approval before execution). The frame work shall be fixed in true horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for the purpose of payment, stainless steel cramps shall be paid for separately and nothing extra shall be paid).

Providing and fixing adjustable stainless steel cramps of approved quality, required shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not less than 260 gms), for dry stone cladding fixed on frame work at suitable location, including making necessary recesses in stone slab, drilling required holes etc complete as per direction of the Engineer-in-charge.

Applying breathable, non-reactive, antifungal, and water repellant Silane/Siloxane chemical as approved by Archaeological Survey of India/ Engineer-in-charge, of approved brand and manufacture, diluted with solvent mineral Turpentine oil in the ratio of 1:12 (One part of approved chemical :12 Part of Turpentine oil), on the existing sand stone masonry surface with two or more coats to give uniform application of chemical on the surface, all complete as per direction of Engineer-In-charge (The rate is inclusive of all materials & labours involved except scaffolding).

Extra for stone work for wall lining on exterior walls of height more than 10 m from ground level for every additional height of 3 m or part there of.

Providing and fixing approved brand and manufacture SS 304 Lever Handle D-type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade SS 304 grade Mortice lock with key cylinder fixed fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade wall mounted door buffer fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Door Stopper - door mounted hanging type fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Top & Bottom Patch fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade D type 1200mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade D type 300mm Pull Handle with 32mm dia fixed with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Providing and fixing approved brand and manufacture SS 304 grade Glass to Glass Lock Round type with SS screws etc. complete in all respects as per manufacturers' specifications & as directed by Engineer-in-charge.

Toilet Cubical Providing and fixing Toilet Cubicle (of following standard dimension which includes 600 mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant 12 mm thick solid compact laminate panels Finish of the compact laminate should be raw silk which include doors, pilasters and intermediate panels finished with approved texture/shade as per the detail drawing and as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of Stainless Steel (Grade 316) as per manufacturer's specifications and EIC instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset indicators, (4) Coat hooks, (5) U- Channels, (6) SS-Shoe Box Plate, (7) MS-Base Plate, (8) Rubber noise deafening tape, (9) Screws and wall Plugs.

Providing and fixing 18mm thick Granite stone work for wall lining upto 10 m height in cement mortar 1:3 (1cement : 3 coarse sand) including pointing with white cement mortor with an admixture of pigment to match the granite shade complete as per direction of Engineer-in-charge.

Providing and fixing 18mm thick pre-polished granite stone strip of any colour and shade 60mm wide with one edge round moulded and polished, fixing the strip in wall above the top of dado, by cutting chase in wall and fixing the same with cement mortar 1:3 (1cement : 3 coarse sand), neatly finished and fixed such that the outer rounded edge projected 20mm beyond the surface of dado , all complete as per direction of engineer-in-charge.

Providing and Fixing of Tarkett Centra-43 or equivalent make, Size: 2mm thick, 2mtrs. x 20mtrs. imported Vinyl Flooring, 100% recycled flexible, homogeneous antistatic calendared compacted floor covering of approved manufacturer, suitable for heavy traffic areas having total weight 3000 g/m2 in sheet of size 2mtrs. x 20 mtrs. In approved pattern & color combination with PUR – patented polyurethane surface treatment with unique performance in staining providing unrivalled chemical and scratching resistance. Having wear resistance of ≤ 4.0mm3 as per EN 660.2 and Wear Resistance Group ‘T’ as per EN and should have a residual indentation of <0.01mm confirming to EN-433. The laid flooring should have Non- directional design, color dyed as a raw mixture to ensure even color throughout the thickness and its surface should be densely compacted for improving wear and ease of maintenance with Anti- bacterial and Fungicidal properties. The joints in the flooring will be sealed by using a PVC welding bar of matching color. The cost is included for Supply and Fixing of Self Leveling Compound (2-3mm approx. thick) all complete as per direction of Engineer-In-Charge.

Supply and Fixing of Tarkett Somwall or equivalent make, 1mm thick, size 2mtrs. X 35mtrs. Imported vinyl wall covering, 100% recycled having total weight 1750 g/m2 in approved pattern & color combination with PUR – patented polyurethane surface treatment with unique performance in staining providing unrivalled chemical and scratching resistance, anti- bacterial and fungicidal properties. all complete as per direction of Engineer-In-Charge.

Providing and fixing Single Glazing 6mm thick toughened glass complete in all respects as per direction of the Engineer-in-charge. (Required properties Solar factor ≤ 0.45, U-Value ≤ (W/sq.m-K) 5.7W /M2K, Visible light transmittance ≥ 0.30)

Waterproofing Treatment for Landscaping Decks/ Terrace Polyurethane based waterproofing system for podium and landscape decks. Base preparation 1. Compressed air cleaning has to be done so as to make the surface free of dust, debris, laitance etc. Repairing cracks by cutting and making V-groove in 25x25 mm, with SBR polymer modified mortar , filling the groove with CM(1:3) mixed with SBR latex 10% by weight of cement 2. Providing and making fillets at the junction of the walls and the slabs using cement mortar of 1:4 mix admixed with 5 % of SBR latex by weight of cement. 3. Provide and applying liquid applied,highly permanent elastic,cold applied & cold curing single component PU based waterproofing coating based on pure elastomeric hydrophobic polyurethane resins having resistance to root penetration, Apply 2 [email protected]/sq.mtr to achieve an avergae thickness of 1.2 .The product must have the following technical properties: Elongation at break 400 % as per ASTM D-412, Tensile strength 4 N/mm2 as per ASTM D412, Shore hardness-65 as per ASTM 2240.The coating must be applied over the prepared substrate primed with PU Primer@180-190 gms/sq.mtr. 4. Providing & laying of minimum 150 gsm geotextile layer. 5. Laying of Protection screed of average 75 mm thick in slope using 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) grade concrete over geotextile as per recommendations (supply of oncrete in scope of civil contractor) FOR LANDSCAPE AREAS Supply and installation of approved make Rolled Matrix Soil Filter cum surface drainage System as per approved manufacturers specifications. consist of dimple raised, moulded polypropylene sheet bonded to a high strength polypropylene geotextile fabric This geotextile fabric composite allows passage of moisture through fabric while preventing fine soil from entering to drainage channel. all complete as specified and as directed by the Engineer-in-Charge :

Providing and fixing 300mm wide 1mm thk grade-304, SS Kick plate over flush door with suitable adhesives, screws etc. all complete as per direction of Engineer-In-Charge.

Providing & Fixing PVC Stretcher Guard minimum 150 mm wide with extruded aluminium base including all accessories per approved design all complete as per direction of Engineer-In-Charge.

Providing & Fixing PVC. Corner guard 40x40x4mm size fixed to wall including fixing arrangement as per approved design all complete as per direction of Engineer-In-Charge.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry density (proctor density).

Supplying and stacking at site. 90 mm to 45 mm size stone aggregate

63 mm to 45 mm size stone aggregate

Supplying and stacking at site. Stone screening 13.2 mm nominal size (type A)

Supplying and stacking at site. Stone screening 11.2 mm nominal size (type A)

Supplying and stacking at site. Moorum

Laying spreading and compacting stone aggregate of specified sizes to WBM specifications including spreading in uni form thickness, hand picking, rolling with 3 wheeled road/vibratory roller 8-10 tonne in stages to proper grade and camber, applying and brooming requisite type of screening/binding material to fill up interstics of coarse aggregate watering and compacting to the required density.

Surface dressing one coat on new surface with bitumen of specified grade at a rate of 1.95 kg/sqm of surface area with 1.5 cum of stone chippings 13.2 mm nominal size per 100 sqm of road surface, including consolidation with road roller of 6 to 8 tonne capacity , etc. complete : Using bitumen emulsion (minimum 50% bitumen content-RS grade conforming to IS : 8887)

Providing and applying tack coat using bitumen emulsion conforming to IS:8887, using emulsion pressure distributer including preparing the surface & cleaning with mechanical broom. With rapid setting bitumen emulsion On bituminous surface @ 0.25kg/sqm

Providing and laying Bitumen Penetration Macadam with hard stone aggregate of quality, size and grading as specified, with bitumen of suitable penetration grade, including required key aggregate as specified, spreading coarse aggregate with the help of self propelled/tipper tail mounted aggregate spreader and applying bitumen by a pressure distributor and then spreading key aggregate with the help of aggregate spreader complete, including consolidation with road roller of minimum 8 to 10 tonne capacity to achieve specified values of compaction and surface accuracy : For 50mm compacted thickness using coarse aggregate of size 50-20 mm graded @ 0.60 cum per 10 sqm key aggregate of size 12.5 mm graded @ 0.15 cum per 10 sqm. With paving asphalt grade VG - 10 @ 50 kg/ 10 sqm.

Providing and laying seal coat over prepared surface of road with bitumen heated in bitumen boiler fitted with the spray set spraying using 98 kg of bitumen of grade VG - 10 and blinding surface with 0.90 cum of stone aggregate of 6.7 mm size (Passing 11.2 mm sieve and retained on 2.36 mm sieve) per 100 sqm of road surface, including rolling and finishing with power road roller all complete. Note: Seal coat items to be operated only with the prior approval of chief Engineer concerned.

Painting runway/taxi track/apron marking with adequate no. of coats to give uniform finish with road marking paint of superior make as approved by the Engineer-in-charge i/c cleaning the surface of all dirt, scales, oil, grease and other foreign material etc. and lining out complete. New work (Two or more coats)

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50 mm thick compacted of coarse sand, filling the joints with coarse sand etc. all complete as per direction of engineer-in-charge.

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement in position to the required line ,level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand) including making joints with or without grooves (thickness of joints except sharp curve shall not be more than 5mm) including making drainage opening wherever required complete etc. as per direction of engineer-in-charge(length of finished kerb edging shall be measured for payment).(Precast C.C. kerb stone shall be approved by engineer-in-charge).

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including geting out and disposal of excavated earth, lead upto 50m and lift upto 1.5m, as directed by Engineer-in-Charge. All kinds of soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in. All kinds of soil.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves,chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing & reinforcement with1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size)

Centring and shuttering including stutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and acees platform

Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of Grade Fe-500D or More.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS: 10910 on 12mm dia steel bar conforming to IS :1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and heaving manufactures permanent identification mark to be visible even after fixing " including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6: (1 cement :3 coarse sand :6 graded stone aggregate 20mm nominal size )complete as per design.

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality. HD-20 circular shape 560 mm internal diameter.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90 metre depth below ground level. All types of soil 400 mm dia.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge. 200 mm nominal size dia.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia.

Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer –in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 ( 1cement : 2 Coarse sand : 4 graded stone aggregate 20 mm nominal size )

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, beyond 90 metre & upto 150 metre depth below ground level. All types of soil (400 mm dia)

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Providing and fixing 80 mm dia. GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete.

Supply, Lowering, installation & testing of KSB make submersible pumping set with 7.5 HP motor 4 stage pump suitable for 20/26/30/38/40/45/50 m3 hr. at 42/38/36/32/29/25/20 mtr. Head respectively. With Three Phase. (Model: 273/4)

Providing & fixing cable 6 sq.mm. From submersible pump to panel board.

Providing & fixing Panel Board for submersible pump fitted with DOL starter ammeter, voltmeter single phase preventer standard/indo/cop make MCB of off switch push bottom duly wired and made out of 16/18 SWG sheet.

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified. 80 mm dia.

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified. 80 mm dia.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly leveling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or/and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 16 mm

Supplying and stacking at site dump manure from approved source, including carriage up to 1 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 4.75 mm

Fine dressing of the ground

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Officer-in-charge (Cost of sludge, dump manure and / or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge..

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 60 cm dia, and 60 cm deep.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 45 cm dia, and 45 cm deep.

Providing and Displaying of Wadelia trilobata plant,full of leaves in 15 cm size of Poly bags & as per direction of the officer-in-charge.

Providing and Displaying of Duranta Golden plant, having ht.15 to 20 cm bushty shape plant with fresh and healthy leaves in 20 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge..

Providing and Displaying of Iresine herbstii plant, of height 20-30 cm. full of branches well developed in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.

Supply and stacking of Alstonia scholaris plant of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Bauhinia blakeana (Kachnar) plant of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Bombax ceiba plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Grevillea robusta (Silver Oak) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Kigelia pinnata plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Melia azedarach plant of height 120-135 cm. in big poly bag of size 25cm as per direction of the officer-in-charge.

Supply and stacking of Michelia champa (Golden Champa)plant of height 90-105 cm. in earthen pots of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Putranjiva roxburghii plant of height 90-105 cm. in big polybag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Jatropha multifida (red colour) of height 60-75 cm. multibranched in p.bag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of plant Calliandra hybrida of height 105-120 cm., well branched, bushy in big size HDPE bag as per direction of the officer-in-charge.

Supply and stacking of plant Gardenia jasminoides of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of plant Nerium oleander (kaner) of height 45-60 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge.

Supply and stacking of Clerodendrum splendens plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Supply and stacking of Jasminum grandiflorum (chameli) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. .

Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors whereever required. (Flushing Cistern to be paid separately). Indian type W.C Orissa pattern of size 580 x 440 mm . C) Jaquar Make, White

Provinding fitting and fixing Vitreous china wall hang water closet (European type W.C PAN 400 mm high) with seat and lead, CP Brass hinges and rubber buffers , CI/MS brackets,40 mm dia flush band with fittings including painting of fittings and brackets, required.(flushing Cistern to be paid separately). C) Jaquar Make, White (i) Florentine Cat. No. FLS-WHT-0111 (inclusive of seat cover and fittings)

Provinding fitting and fixing Vitreous china wall hang water closet (European type W.C PAN 400 mm high) with seat and lead, CP Brass hinges and rubber buffers , CI/MS brackets,40 mm dia flush band with fittings including painting of fittings and brackets, required.(flushing Cistern to be paid separately). C) Jaquar Make, White (ii) Solo Cat. No. SLS-WHT-0117 (inclusive of seat cover and fittings)

Supplying, fiting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately). Parryware make, White (i) Economy Single Flush (Cat No.C8090/C8055)

Supplying ,fitting and fixing concealed cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. compete as directed and specified (pipes will be measured separately). Jaquar make Concealed Cistern ( Cat. No. CIB-WHT-31801011X) with Control Plate (CP) (Cat.No. CIS-CHR-31191510X)

Providing fitting and fixing vitreous china flat back type lipped front urinal; basin of with automatic flushing cistern with standard flush pipe and CP brass spreader andbrass unions,etc. complete including painting of fittings and complete, cutting and making good the walls & brackets, cutting and making good the walls & floors wherever required. Make-Jaquar make , White (i) Urinal (Cat.No. URS-WHT-0704) with Sensor (Cat. No. SNR-CHR-51097)

Suppling fiting and fixing glass division plate of jaquar make including fitting and fixing compate as directed and specified.

Provinding vitreous china wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required.(Pillar cock, stop cocks, waste coupling are to be paid separately ). Table Top Basin -Jaquar Make ii) Solo ( Cat. No. SLS- WHT-0558)

Provinding vitreous china wash basin with CI/MS brackets, C.P brass chain with plug,PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required.(Pillar cock, stop cocks, waste coupling are to be paid separately ). Table Top Basin -Jaquar Make (iii) Lyric ( Cat. No. LYL-WHT-0555)

Providing fitting & fixing stainless steel kitchen sink of parry make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings, cutting & making good the walls wherever required.( Sink cock, stop cocks, waste coupling are to be paid separately . Parryware Make (ii) Single Bowl with Drain board (400x200) flat Edge - Glossy ( Cat. No. C8537)

Providing fitting & fixing laboratory sink of Parryware make with CI/MS brackets, C.P. brass chain with rubber plug, PVC waste pipe etc. complete including painting the fittings ,cutting &making good the walls wherever required. (Sink cock, stop cocks, waste coupling are to be paid separately. Parryware Make , White. (i) Lab Sink 450mm (Cat.No.C0602)

Providing fitting and fixing Decorative Mirror complete as directed and specified. Parryware Make (a) Size 800mmx600mm

Providing fitting and fixing Decorative Mirror complete as directed and specified. Parryware Make (b) Size 600mmx 450mm

Providing,fitting and fixing CP soap tray / soap dish complete as directed and specified. Jaquar make- ( e) Hotelier (Cat.No. AHS - 1531)

Providing fitting and fixing liquid soap dispenser and liquid soap container complete as directed ad specified. Jaquar make- ( c) Kubix with glass bottle (Cat.No. AKB-35735)

Providing fitting and fixing CP towel rail complete as direted and specified. Jaquar make- (vii) Kubix(600mm long) (Cat.No. AKB-35711)

Providing, fitting and fixing Chrome Plated towel ring complete as directed and specified. Jaquar make- (ii) Continental towel ring round (Cat.No. ACN-1121BN)

Providing ,fitting and fixing chrome plated robe hook complete as direted and specified. Jaquar make- (iii) Kubix (Cat.No.AKB-35791)

Providing, fitting and fixing chrome plated tumbler holder complete as directed and specified. Jaquar make- (iii) Kubix (Cat.No.AKB-35741)

Providing fitting and fixing chrome plated TOILET PAPER holder of complete as directed and specified . Jaquar make-(ii) Continetal toilet paper holder with flap(cat.No. ACN1153N)

Providing fitting and fixing chrome plated TOILET PAPER holder of complete as directed and specified . Jaquar make-(vii) Kubix toilet roll holder with cover (Cat.No. AKB-35753)

Providing ,fitting andd Fixing chrome plated waste coupling complete as directed and specified. Jaquar make- (i) 32mm (HT/FT) (Cat.No. ALD-705/709

Providing ,fitting andd Fixing chrome plated Bottle Trap complete as directed and specified. Jaquar make- (i) Bottle trap (with internal partition) 32mm size with 250mm long wall connection pipe(Cat.No.ALD-769)

Supplying fitting and fixing C.P bib cock 15 mm dia of approved brand as directed and specified (G.I & C.P pipes will be measured separately). Jaquar make-(a) Continental / clarion (ii) Bibcock long thread

Supplying fitting and fixing C.P bib cock 15 mm dia of approved brand as directed and specified (G.I & C.P pipes will be measured separately). Jaquar make-(a) Continental / clarion (iii) 2-Way bib cock

Supplying fitting and fixing chorom plated (C.P) stop- cock of approved brand and size as mentioned below as directed and specified.(G.I) & C.P Pipes will be measured and paid separately). Jaquar-(a) Continental / Clarion (iii) 15mm (Angular stop cock with long thread )

Supplying and fiiting fixing C.P pillar cock of 15 mm dia of approved brand as specified and directed. Jaquar make- (a) Continental

Supplying,fitting and fixing chorme plated (C.P) shower 15 mm dia. Of approved nrand as directed and specified.( pipes will be measured and paid separately) . Jaquar Make - (a) Continental (ii) Shower arm 190mm long heavy casted body with wall flange

Supplying,fitting and fixing chorme plated (C.P) shower 15 mm dia. Of approved nrand as directed and specified.( pipes will be measured and paid separately) . Jaquar Make - (a) Continental (iii) Pressure adjustable shower with revolving joint

Supplying, fitting and fixing Chorme plated (C.P) basin mixer complete as directed . Jaquar make (For VIP use. Prior approval of chief Enginner PWD (Bidg) must be taken before use)-(a) Continental/ Clarion (iii) Central hole basin mixer without popup waste system with 450mm long coper pipe and brass nuts Cat.No. 169

Supplying, fitting and fixing Chrome Plated (C.P) sink mixer complete as directed. Jaquar make- (a) Continental / Clarion (i) Sink mixer with swinging casted spout ( wall mounted model) Cat No. 309

Supplying fitting and fixing Chrome plated (C.P) bath tub spout of approved brand complete as directed. Jaquar make - (a) Continental (ii) Bath tub spout 235 mm long with wall falnge Cat No. 433

Supplying , fitting and fixing Chorme Plated (C.P) divertor of approved brand complete as directed . Jaquar make (a) Continental/ Clarion - 4 way divertor for concealed fitting with build in non return valves with divertor handle Cat. No.421

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified.In Exposed Surface or in Trenches.-160mm dia.

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified.In Exposed Surface or in Trenches.-110mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified.In Exposed Surface or in Trenches.-75mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified.In Exposed Surface or in Trenches.-63mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified.In Exposed Surface or in Trenches.-50mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.- 160mm dia.

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.- 110mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.- 75mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.- 63mm dia

Supplying, fitting and fixing PVC pipes of 6 kg/cm2 (supreme/Price) or other ISI approved including joining, fitting and fixing with clamps etc.as necessary complete at all levels including below G.L as directed and specified. Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages.- 50mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 160mm dia.

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 110mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 75mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches. 50mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 160mm dia.

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 110mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 75mm dia

Supplying fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. 50mm dia

Supplying fitting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches.- 110mm dia

Supplying fitting and fixing 87.5 degree PVC bend with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified .Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. -110mm dia

Supplying fitting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches - 160mm dia.

Supplying fitting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches - 110mm dia

Supplying fitting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches - 75mm dia

Supplying fitting and fixing 45 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches - 50mm dia

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches.- 160mm dia.

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches.- 110mm dia

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . In Exposed Surface or in Trenches.- 50mm dia

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. -160mm dia.

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. -110mm dia

Supplying fitting and fixing PVC plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.Las directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. -50mm dia

Supplying fitting and fixing PVC plain single tee with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches.-110mm dia

Supplying fitting and fixing PVC plain single tee with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. -110mm dia

Supplying fitting and fixing PVC plain single Y of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches.-160mm dia.

Supplying fitting and fixing PVC plain single Y of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches.- 110mm dia

Supplying fitting and fixing PVC plain single Y of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. -160mm dia.

Supplying fitting and fixing PVC plain single Y of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages. -110mm dia

Supplying fitting and fixing PVC plain single Y with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches- 110mm dia

Supplying fitting and fixing PVC plain single Y with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . Concealed by chiselling or breaking brick wall/C.C./R.C.C and making good to the damages - 110mm dia

Supplying fitting and fixing PVC coupler of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches -110mm dia

Supplying fitting and fixing PVC coupler of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches -75mm dia

Supplying fitting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches - 160mmx110mm

Supplying fitting and fixing PVC reducing Tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc.as necessary complete at all levels including below G.L as directed and specified . In Exposed Surface or in Trenches - 110mmx75mm

Supplying fiting and fixing PVC reducing Tee with door of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified. 160mmx110mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified- 110mm

Supplying fiting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified- 75mm

Supplying fiting and fixing PVC cleaning pipe of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified - 160mm

Supplying fiting and fixing PVC cleaning pipe of (Supreme/Prince) or other ISI approved including joinning, fitting and fixing etc. in exposed surface or trenches as necessry complete at all levels including below G.L as directed and specified - 110mm

Providing fitting and fixing PVC of cowel of ISI make complete as directed and specified - 110mm dia . PVC cowel of ISI make

Providing fitting and fixing PVC of cowel of ISI make complete as directed and specified - 75mm dia . PVC cowel of ISI make

C.P. Grating - 160mm

C.P. Grating -110mm

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories). In internal Wall - Exposed on Wall -20 mm OD

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories). In internal Wall - Exposed on Wall -25 mm OD

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories). In internal Wall - Exposed on Wall -32mm OD

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories). In internal Wall - Exposed on Wall -40 mm OD

Supplying fitting and fixing Ajoy Flowguard CPVC (Chlorinated Polyvinyl Chloride) pipes having thermal stability for hot and cold water supply including all CPVC Plain and bruss threaded fitting including clamps at 1.00 m spacing including joining of pipes and fitting with one step CPVC solvent cement and testing of joints complete at all levels as directed and spcified. (Note: Ball Valve and union will be charged extra and does not comes under Accessories). In internal Wall - Exposed on Wall -50 mm OD

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. Exposed on Walls- 50 mm dia (medium) ,Using Tata make

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. 40 mm dia (Medium) -Using Tata make

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. 32 mm dia (Medium)- Using Tata make

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. 25 mm dia (Medium) -Using Tata make

Suppling fitting and fixing G.I pipes of following sizes, with all necessary 'R' brand or similar approved G.I. fittings such as bend,tee,elbow, reducer,nipple,plug,long screw fitting,H.W. clamps etc. complete at all levels including below G.L as directed and specified. 20 mm dia (Medium )-Using Tata make

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls- 20 mm OD

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls- 25 mm OD

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls- 32mm OD

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls- 40 mm OD

Providing and fixing Chlorinated polyvinyle Chlorinated polyvinyle chloride (CPVC)Pipes, having thermal stability for hot and cold water supply including all CPVC plain with brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing .This includes jointig of pipes. Concealed pipe with cutting chase & making good the walls- 50 mm OD

Supplying fitting and fixing pipes with all necessary fitings in exposed or in treches including trenching and refilling the same etc complete as directed. G.I pipe with GI fitting - TATA / SAIL (Medium) 80mm diameter

Supplying fitting and fixing pipes with all necessary fitings in exposed or in treches including trenching and refilling the same etc complete as directed. G.I pipe with GI fitting - TATA / SAIL (Medium) 100 mm diameter

Supplying fitting and fixing pipes with all necessary fitings in exposed or in treches including trenching and refilling the same etc complete as directed. CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe)- 25mm(OD) diameter

Supplying fitting and fixing pipes with all necessary fitings in exposed or in treches including trenching and refilling the same etc complete as directed. CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe)- 32mm (OD)diameter

Supplying fitting and fixing pipes with all necessary fitings in exposed or in treches including trenching and refilling the same etc complete as directed. CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe)- 40mm (OD)diameter

Supplying fitting and fixing pipes with all necessary fitings in exposed or in treches including trenching and refilling the same etc complete as directed. CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe)- 50 mm (OD)diameter

Supplying fitting and fixing pipes with all necessary fitings in exposed or in treches including trenching and refilling the same etc complete as directed. CPVC pipe with CPVC fitting (Using SUPREME/ PRINCE /SFMC/ FUSION brand pipe)- 75mm(OD) diameter

Reverse Osmosis (RO) for best Quality Drinking Water. Taurus-250 LPH do 100 Litres Storage

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :- 20 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :- 25 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :- 32 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :- 40 mm dia nominal bore

50 mm dia nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :- 65 mm dia. nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :- 80 mm dia. nominal bore

Painting G.I. pipes and fittings with synthetic enamel white paint with two coats over a ready mixed priming coat, both of approved quality for new work :- 100 mm dia. nominal bore

Painting G.I. pipes and fittings with two coats of anticorrosive bitumastic paint of approved quality. - 80 mm dia. nominal bore

Painting G.I. pipes and fittings with two coats of anticorrosive bitumastic paint of approved quality. - 100 mm dia. nominal bore

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : - 25 mm dia nominal bore

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : - 32 mm dia nominal bore

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : - 50 mm dia nominal bore

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : - 80 mm dia. nominal bore

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work : - 100 mm dia. nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :- 20mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :- 25mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :- 32mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :- 40mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :- 50mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :- 65mm nominal bore

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified: - 65 mm dia

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified: - 80 mm dia.

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified: - 100 mm dia.

Providing and fixing hand shower (Health faucet) with 1.2mtr long with 8mm dia Easy Flex Tube with wall hook and flow restrictor with flow rate 6 litre per minute at 3 bar in chrome finish and wall hook. ( MAKE-1: JAQUAR, MODEL NO. HEALTH FAUCET : ALD-CHR-573GA OR EQUIVALENT.)

Providing & fixing wall mounted 300mm Long SS Grab Bar including cutting & making good the walls. ( MAKE-1: JAQUAR, MODEL NO. GRAB BAR : AKP-CHR-35701PS OR EQUIVALENT.)

Providing and fixing Stainless Steel Swing Handicap Grab Bar ,Including cutting and making good the walls wherever required. ( MAKE-1: JAQUAR, MODEL NO. GRAB BAR : WAC-WHT-BG0800 OR EQUIVALENT.)

Providing and fixing of fully automatic "NO TOUCH" durable & shock proof hand drier of approved make & manufacture suitable to operate on 220 volts, single phase 50 hz, A.C. power supply, 1500 Watt and directly plugged to power point complete in ABS plastic body having drying time 20-30 seconds complete as per direction of Engineer in Charge. The rate include cost of all material & labour involved in the item complete and all as per direction of engineer incharge. ( MAKE JAQUAR MODEL NO.- HDR-SAP-M99ACS or EQUIVALENT.)

Providing and fixing 150 litre/ hr. cooling and storage capacity,fully stainless steel electric storage type water cooler ( Blue Star model No. SDLX 15150 or equvalant) with inlet hose connection inbuilt float valve. 2 Nos. outlet foucet, drain tray with waste and pipe up to fllor trap heavy compressor and wire up to socket, 3 pin plug etc complete in all respect.

Providing and fixing uPVC P-Trap including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand: 4 hand stone ballast 20 MM nominal size) the inlet from floor level to trap rim to be grouted and cemented neat manner including cutting and making good the floor & wall wherever requiredcomplete in all respects 110 mm inlet and 110 mm outlet.

Providing and fixing cast brass clean out plug with suitable insert keys for opening, male threaded joint with PP/ uPVC female threaded socket caulked to PP/ uPVC pipe including cost of Solvent cement or Other Joint.- 100 mm dia

Providing and fixing cast brass clean out plug with suitable insert keys for opening, male threaded joint with PP/ uPVC female threaded socket caulked to PP/ uPVC pipe including cost of Solvent cement or Other Joint.- 150 mm dia

Providing and fixing in position 110x63 mm OD uPVC reducing elbow including fix to floor with cement mortar.

Providing and fixing 110 mm OD uPVC inlet fitting/ Extension Piece with 2 or 3 inlets of 40 to 63 mm OD, fixed to uPVC trap with solvent cement joint and set in cement concrete as per drawing complete.

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification. 6 mm thick (Concealed Pipes)- For 20 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification. 6 mm thick (Concealed Pipes)- For 25 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification. 6 mm thick (Concealed Pipes)- For 32 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including all required accessories complete as per specification. 6 mm thick (Concealed Pipes)- For 40 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including protection by wrapping with 24 gauge alumminium sheet with riveted screw joints all required accessories complete as per specification. 13 mm thick (Exposed Pipes)- For 20 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including protection by wrapping with 24 gauge alumminium sheet with riveted screw joints all required accessories complete as per specification. 13 mm thick (Exposed Pipes)- For 25 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including protection by wrapping with 24 gauge alumminium sheet with riveted screw joints all required accessories complete as per specification. 13 mm thick (Exposed Pipes)- For 32 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including protection by wrapping with 24 gauge alumminium sheet with riveted screw joints all required accessories complete as per specification. 13 mm thick (Exposed Pipes)- For 40 mm dia Pipe

Providing and fixing Thermoflex or Kaiflex thermal insulation tubing, a elastomeric flexible material having hermetic blister closed cell structure of expanded synthetic rubber over pipes of following nominal bores and thickness including protection by wrapping with 24 gauge alumminium sheet with riveted screw joints all required accessories complete as per specification. 13 mm thick (Exposed Pipes)- For 50 mm dia Pipe

Providing and fixing forged brass single acting air release valve with screwed inlet 25 mm dia.

Providing, laying and Jointing G.I. "B class" pipes and fittings conforming to IS: 1239 (Medium class) with fittings, union and clamps including cutting holes in wall, makes chases in wall and making good the same in cement mortar 1:2 (1cement : 2 coarse sand) complete in all respects for internal works including pipe supports with galvanised GI. slotted angle iron, GI clamps, spacers as required and making good wherever required. (For Vertical in Shafts & Terrace only) Internal Work - Exposed on Wall- 65 mm dia. nominal bore

Providing, laying and Jointing G.I. "B class" pipes and fittings conforming to IS: 1239 (Medium class) with fittings, union and clamps including cutting holes in wall, makes chases in wall and making good the same in cement mortar 1:2 (1cement : 2 coarse sand) complete in all respects for internal works including pipe supports with galvanised GI. slotted angle iron, GI clamps, spacers as required and making good wherever required. (For Vertical in Shafts & Terrace only) Internal Work - Exposed on Wall- 80 mm dia. nominal bore

Providing, laying and Jointing G.I. "B class" pipes and fittings conforming to IS: 1239 (Medium class) with fittings, union and clamps including cutting holes in wall, makes chases in wall and making good the same in cement mortar 1:2 (1cement : 2 coarse sand) complete in all respects for internal works including pipe supports with galvanised GI. slotted angle iron, GI clamps, spacers as required and making good wherever required. (For Vertical in Shafts & Terrace only) Internal Work - Exposed on Wall- 100 mm dia. nominal bore

Supply, Installation, Testing & Commissioning of 3000 LPD Flat Plate based on thermo syphon solar water heating System suitable on greavity feed water including internal system piping, insulated hot water storage tank with heat exchanger, valves on inlet & outlet, Y strainer temperature gauge, MS Angle frame etc. Details of each items used in one 3000 LPD system are mentioned below. 24 Nos. Solar Flat Plate collector having collector area should be min. 2 Sq, Mtr. (Collectror should be BIS & MNRE approved. One No. Horizontal/Vertical hot water mixing tank of 2000 ltr capacty shall be made out by 1.6 mm thick stainless steel 316 grade sheet ,100 mm thick rock wool/glass wool slab insulation (density of glass wool 64 Kg/Sqm.) covered with chicken mesh & 22 SWG aluminum sheet cladding outside the tank. Tank shall be provided with flanges for inlet outlet, over flow/ drain connection & Vent pipe with M H cover of 450 mm internal dia., Temperature and pressure release valve should be on top of water storage tank . 1 Lot of Inter-connected CPVC system piping of required size with fittings, insulated with 50 mm glasswool/rockwool insulation covered with chicken mesh & 26 SWG aluminum cladding to connect the collectors with hot water storage tank. Providing and fixing a lot of Temperature Gauge, vent pipe, ball valve , NRV, CI/brass Y strainer, PT - 100 sensors with thermocople wire ,MS. Angle stand for hot water tank .. One No. Heat Exchanger cage type inbuild the hot water storage tank of SS 316 having surface area not less than 2.4 Sq. Mtr.. One No. Control Panel for recirculation pump having DTC with contractor, MCBs, and cycling timer for pump.. Three Nos. Electric heater of 9 KW. With Thermostatic control. Solar System as Described Above

Supply, installation, testing & commissioning of vertical inline hot water reciculation pumping set ( set of 2 pumps 1 Working + 1 Stand by) of 60 LPM Capacity at 15 Head with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with control valves, power & control cables, suction/ delivery headers,vibration eliminating pads under foundations,vibration eliminators, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :- 150 mm diameter

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :- 200 mm diameter

Providing, laying and jointing glazed stoneware pipes grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :- 250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design. :- 150 mm diameter S.W. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design. :- 200 mm diameter S.W. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) all round S.W. pipes including bed concrete as per standard design. :- 250 mm diameter S.W. pipe

Constructing brick masonary circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design: 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter confirming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885

Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to 1.67m. With Sewer bricks conforming IS : 4885

Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68 m to 2.29 m : With Sewer bricks conforming IS : 4885

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 2.30 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With Sewer bricks conforming IS : 4885

Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m : With Sewer bricks conforming IS : 4885

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement and making necessary channels for the drain etc. complete : For pipes 250 to 300 mm diameter

Providing and Installing Grease Separator EasyClean ground Standard NS 2 . Based on Euro-Norm EN 1825-1 Manufactured from Polyethylene. For underground installation, installation depth 550 - 950 mm, with integrated sludge trap, polymer upper section, vertically adjustable, rotatable and tiltable up to 5°, cast iron cover in load class B based on EN 124, odor tight. Ø 110 in- and outlet according to DIN 19534 Sludge trap capacity: 200 l Total separator capacity: 370 l Fat storage: 120 l Certification: Z-54.1-440 Weight: 120 kg Dimension: 1470 x 1300 mm Inspection chambers may be installed in a maximum of 500 mm groundwater.

Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m. All kinds of soil- Pipes, cables etc. exceeding 80mm dia but not exceeding 300mm dia.

Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed, within a lead of 50m. All kinds of soil- Pipes, cables etc, exceeding 300 mm dia but not exceeding 600 mm dia

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth upto 1.5 metre). Pipes, cables etc, exceeding 80mm dia but not exceeding 300mm dia

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth upto 1.5 metre). Pipes, cables etc, exceeding 300 mm dia but not exceeding 600 mm dia

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40mm nominal size) up to haunches of S.W/RCC pipes including bed concrete as per standard design. 250 mm diameter

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :- 250 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :- 450 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :- 600 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :- 700 mm dia. R.C.C. pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :- 800 mm dia. R.C.C. pipe

Constructing brick masonary circular type manhole 0.91m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1 :3:6 mix (1 cement : 3 coarse sand : 6 graded 40mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement all complete as per standard design: 0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560mm internal diameter confirming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) with beyond 0.91m to 1.67m. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement, all complete as per standard design : 1.68 m deep with SFRC Cover and frame (heavy duty HD-20 grade designation) 560mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182kg. fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22m internal dia (at bottom) beyond 1.68 m to 2.29 m : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing bricks masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth beyond 45 cm of brick masonry chamber. :For 455x610 mm size. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Filter Feed Pump ( Dom. Water) at Water Supply Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 10.0 LPS Head 25 M. HP 5.0 HP Approxi.

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Domestic Water Transfer at Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 10.0 LPS Head 75 M. HP 15.0 HP Approxi.

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Flushing Water Transfer STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 5.0 LPS Head 75 M. HP 7.5 HP Approxi.

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Softener Feed Pump ( Cooling Tower) at STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 4.0 LPS Head 25 M. HP 2.5 HP Approxi.

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Soft Water Transfer Pump at STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 4.0 LPS Head 75 M. HP 6.0 HP Approxi.

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Irrigation Pumps at STP Pump Room Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 2.0 LPS Head 40 m HP 2 HP Approx.

Providing, installing, testing and commissining of variable speed (VSPS) hydropneumatic system mounted on a common base plate comprising of vertical centrifugal pumping set with S.S body, stainless steel impeller and mechanical seal, shaft directly coupled to a TEFC induction motor suitable for 400/440 volts, 3 phase, 50 cycles AC supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, one No. microprocessor based controller, dedicated variable frequency drive for each pump, one No.remote sensors, pressure transducers, sequence running cotroller, dry running Protection,motor control centre, necessary power and control cabling from MCC to pumps including required rating of MCB, one No. 60 litre capacity M.S diaphragam tank with interchangeable butyl rubber membrane,complete in all respects including stainless steel grade 316 pipe suction and delivery headers and isolation/ control valves( ball valves/butterfly valves/ Nan return valves/ vibration eliminators etc as required) , power box, equipped with fuses/ isolators/circuit breakers as required. The entire Hydropneumatic system shall be factory fitted. Hyd. System for Domestic Water Supply at Hospital Terrace Set of Two Pumps ( 1 Working+ 1 Standby) Capacity 5.0 LPS Head 20 M. HP 3.0 HP Approxi.

Supply, installing, testing and commissioning of submersible open impeller non-clog pumps with C.I.body and to TEFC submersible motor for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, guide pipe and chain in built level controller, sequence running controller, arrangement for both pumps together inacase of emenegency, audible hooter for failure or flooding, dry running Protection complete in all respects., painting, testing and commissioning complete with approved quality and make as required as per instruction of site incharge. (Pumps shall be installed in a set of two pumps One working and One standby) Basement & Pump Room Drainage Pumps (Pumps to be suitable to handle solids upto 12 mm size) Capacity - 4.0 LPS (Each) Head - 20 M H.P. - 2.0 HP Approx.

Supply, installing, testing and commissioning of submersible open impeller non-clog pumps with C.I.body and to TEFC submersible motor for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, guide pipe and chain in built level controller, sequence running controller, arrangement for both pumps together inacase of emenegency, audible hooter for failure or flooding, dry running Protection complete in all respects., painting, testing and commissioning complete with approved quality and make as required as per instruction of site incharge. Sewage Sump Pumps (Pumps to be suitable to handle solids upto 40 mm size) Capacity - 4.0 LPS (Each) Head - 20 M H.P. - 3.0 HP Approx.

Supply Installation,Testing & Commissioning of vertical self supporting Filter fabricated from MS sheet as per IS: 2825, ((minimum thickness of shall 6 mm and dished end 8 mm)) pressure gauges, sample cock, GI class 'C' face piping, CI butterfly valves and all accessories , with initial charge of filter media including anthracite, painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testing and commissioning complete. Dual Media Filter For Domestic Water Supply Capacity- 37500 LPH Filtration rate- 16000 LPH/Sqm. Filter dia approx. - 1800 MM Working pressure: 3.0 Kg/sq cm. Test pressure : 4. 5 Kg/sq cm

Supply Installation,Testing & Commissioning of vertical self supporting Filter fabricated from MS sheet as per IS: 2825, ((minimum thickness of shall 6 mm and dished end 8 mm)) pressure gauges, sample cock, GI class 'C' face piping, CI butterfly valves and all accessories , with initial charge of filter media including anthracite, painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testing and commissioning complete. Activated Carbon Filter For Domestic Water Supply Capacity- 37500 LPH Filtration rate- 16000 LPH/Sqm. Filter dia approx. - 1800 MM Working pressure: 3.0 Kg/sq cm. Test pressure : 4. 5 Kg/sq cm

Supply Installation,Testing & Commissioning of "Cation" ion exchange Water Softener fabricated from MS plate as per IS: 2825 (minimum thickness of shall 6 mm and dished end 8 mm) complete with initial charge of resins , GI class 'C' face piping, CI butterfly valves, pressure gauge, hydraulic brine injector, accessories, painting inside with epoxy paint, including 500 liters capacity PVC / HDPE brine tank suitable for 2 regeneration capacity, testing and commissioning complete with resins of approved quality and make. Softener For Cooling Tower Water Supply Hardness- Inlet- 500-600 PPM Outlet- Less than 5 PPM Capacity- 15000 LPH Regeneration period 12 hrs. Quantity of soft water between two regenerations = 180000 lit Working pressure: 3.0 Kg/sq cm. Test pressure : 4. 5 Kg/sq cm

Supply Installation,Testing & Commissioning of metering pump type chemical doser with 100 lits. HDPE chemical grade solution tank,injection fitting assembly,suction and delivery hose upto the point of injection, capacity 0-6 lph, complete in all respects. Chlorination of Domestic Water

Supplying, installing, testing and commissioning controllers with low voltage relays, stainless steel probes and PVC shroud wiring from tank top to probes of required. Level Controller For Water Supply Pump: To start pump when water level is low in Domestic Water U.G. tank and shut off pump when Domestic Water U.G. tank is full. Also to stop when water level is low in raw water underground tank.

Supplying, installing, testing and commissioning controllers with low voltage relays, stainless steel probes and PVC shroud wiring from tank top to probes of required. Level Controller For Sump Pumps: To start pump when water level is high in sump and shut off pump when sump is empty. Both pumps are start when sump is over flowing.

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. 50 mm dia

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. 65 mm dia

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. 80 mm dia

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. 100 mm dia

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete. 150 mm dia

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . 50 mm dia

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . 65 mm dia

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . 80 mm dia.

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . 100 mm dia.

Butterfly valve (manual) with C.I body SS disc nitrile sheet & O ring & PN 16 Pressure rating as specified . 150 mm dia

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified. 50 mm dia

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified. 65mm dia.

Non - return valve with dual plate of CI Body SS plates vulcanized NBR seal flanged end & PN 16 rating as specified. 80 mm dia.

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 16 Kg/Sqcm. - 50 mm dia

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 16 Kg/Sqcm. - 65 mm dia

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 16 Kg/Sqcm. - 80 mm dia

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. Power cable Copper 3 core 10 sq.mm

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. Power cable Copper 3 core 6 sq.mm

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. Power cable Copper 3 core 4 sq.mm

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects. Control cable copper 2 core 1.5 sq.mm

Supply, installation, testing and commissioning of double wall insulated stainless steel water storage tank (inner sheet is SS 316 & outer sheet of SS-304), thickness of sheet as per manufacturer specification, placed at terrace level with inlet, outlet, overflow connection complete with 25 mm dia bend for vent, ball valve for scour, mosquito proof brass overflow grating and 600 mm dia manhole cover with locable arrangment completeas per direction of Engineer-in-charge. 1500 Litres Capacity for RO Water

Providing and fixing F.R.P. Grating drain cover M.S. Angle ( 35 x35 x 5 mm). ( Load Bearing cap. 2.5 T, suitable for car parking, basement, Pump room, Parking Area ) THERMO DRAIN or Equivalent. 377mm wide and 30mm thick

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and consisting of following, complete in all respects, as required : (Jockey Pump). (a)Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. (b)Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. (c )M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered and with anti vibration pads. 180 lpm at 88 m Head (For Hydrant & Sprinkler System).

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. It should be complete as per specifications & directions of Engineer-in-charge. 4 x 25 sqmm ( 28 mm )

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required. It should be complete as per specifications & directions of Engineer-in-charge. 3.5 x 50 sqmm ( 35 mm )

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 150 mm width x 50mm depth x 1.6 mm thickness.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing, fixing, tetsing & commissioning of annunciator panel for flow control switches, providing audio /visual indication of actuation of automatic sprinkler system for each zone complete as per specifications. The panel should have interface for connection to complete controlled building management system. The panel should have:- a) Fault indication for each zone b) Indication of zone fire c) Fire/Fault hooter d) Alarm Panel for fire/fault e) Battery for emergency f) Battery Charger g) mains supply and shall cater for minimum 14 zones working and 6 zones spare

Supplying & laying one number XLPE insulated PVC sheathed Aluminium Conductor armoured UG cable of 1.1 KV grade Conforming to IS 7098/1988 with upto date ammendment of following size in the existing RCC/HUME/ METAL /GI /CI /Stoneware/DWC pipe/ masonary Open Duct/ cable tray/ open in air etc. as requred. 4 core, 25 sq.mm. Aluminium Armoured

Supplying & laying one number XLPE insulated PVC sheathed Aluminium Conductor armoured UG cable of 1.1 KV grade Conforming to IS 7098/1988 with upto date ammendment of following size in the existing RCC/HUME/ METAL /GI /CI /Stoneware/DWC pipe/ masonary Open Duct/ cable tray/ open in air etc. as requred. 3.5 core, 50 sq.mm. Aluminium Armoured

Supply and fixing in position 1 m wide Insulation mat made of elastomeric polymers Material (Class -A) of 415V grade as per IS 15642-2006 . Thickness of insulation mat shall be not less than 2 mm to withstand 1.1 KV dielectric strength AS PER IS 15652 : 2006. It should be complete as per specifications & directions of Engineer-in-charge.

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. ( For Underground ) 150 mm. Dia

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. ( For Underground ) 100 mm. Dia

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required. ( For Underground ) 80 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 25 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 32 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 40 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 50 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 65 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 80 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 100 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 150 mm dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 200 mm dia (wall thickness 6.3 mm)

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required. (Plant Room piping/Vertical Riser/Downcomer/Floor) 250 mm dia (wall thickness 6.3 mm)

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required : Single headed Stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 50mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 80 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 100 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 150 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 200 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 250 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 80 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 200 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required : 250 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. : 150 mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. : 200 mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required : Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 40 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless Steel (Grade 304)

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 2 way-100 mm dia M.S. Pipe. (FOR UG TANK )

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required : 4 way - 150 mm dia M.S. Pipe. (FOR UG TANK & RISER)

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Pendent Sprinkler

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Upright Sprinkler

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories : Horizontal side wall sprinkler

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 100mm dia

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required. 150mm dia

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required : 150mm dia

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 700 mm

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1000 mm

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1200 mm

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required. 1500 mm

Supplying, installation, testing & commissioning of deluge valve (to be used for water curtains) UL listed with wet pilot basic trim assembly for DVA with test and alarm, drip and drain valve with water motor gong complete as required. 100 mm dia

Supplying, installation, testing & commissioning of deluge valve (to be used for water curtains) UL listed with wet pilot basic trim assembly for DVA with test and alarm, drip and drain valve with water motor gong complete as required. 150 mm dia

Providing, installation, testing & commissioning of water curtain nozzle 15mm dia nickel chrome plated brass, BSPT, K-factor as per design consideration complete as required.

Providing, installation, testing & commissioning of electric release trim assembly for deluge wall with two way solelnoid valve, weather proof operation on 24 volts DC supply complete as required.

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Providing and fixing in position the industrial type pressure gauges with gun metal / brass valves complete as required

Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete.

Providing & Fixing of MS door made up of 16 gauge MS Sheet capable of accommodating fire hose reel, landing valve, hose pipes, fittings, 1 No. CO2 & 1 No. Dry podwer type portable fire extinguishers & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with one coat of primer & two coat of finished stove enamelled post office red colour paint & "FIRE HOSE" written on front. (Approx. size of door: 2100 mm HEIGHT, WIDTH OF DOOR AS PER SHAFT SIZE )

Providing and fixing hose cabinet of size 700mmX600mm made of 16 gause thick MS sheet with 4 mm thick float glass doors in front painted "FIRE" in red paint i/c recessary locking arrangement suitable to accommodate external hydrant with butterfly valve 2 nos. 15 mtr. long hose pipe. 1 no. brach pipe mounted on wall or raised brick platform & duly painted with post office red externally and white internally with synthetic enamel paint complete in all respects for external hydrant. as directed by Engineer-in-Charge.

Pressure Vessel Supplying, installing, testing and commissioning of pressure vessel for pressurization of fire system complete with valves at outlet / drain to operate as per operating sequences including 25 mm dia drain valve, air release valve with stop cock on the top, outside with one coat of primer & two coats of synthetic enamel paint of approved shade complete as required to operate commonly main fire pump, sprinkler pump & jockey pump at drop of pressure, automatically at required pressure setting. Complete as per manufacturer's specifications & as directed by Engineer- in-charge. working pressure:- 11 kg/sqcm test pressure: 20 kg/sqcm (450 mm dia & 2000 mm height)

Providing, Fixing, testing and commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 11 Kg/cm2 and test pressure 16 Kg/cm2 to provide relief from stresses at pipe flanges. 150 mm dia

Providing, Fixing, testing and commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 11 Kg/cm2 and test pressure 16 Kg/cm2 to provide relief from stresses at pipe flanges.80 mm dia

Supply, fixing, testing and commissioning of screwed type brass/bronze lever operated ball valve of full flow with stainless steel ball (AISI 304 & spindle AISI 410) with setting & gland of superior quality having minimum working pressure of 16 kg/sqcm. 25 mm Dia

Providing and fixing 25 mm dia inspection & testing assembly with gun metal ball valve, gun metal sight glass connection to drain pipe/riser.

Providing & fixing cast iron 100 mm dia. Foot valve with nuts, bolts, 1.5 mm thick CAF gasket complete with all accessories (To be provided into UG Fire Water Tanks).

Providing, fixing water flow meter on test line complete with all accessories for flow indication , monitoring & testing of fire pumps with bypass arrangment including piping & bypass valves. 150 mm dia

Providing and fixing of carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase ingernal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming ro IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with internal charge. Capacity 4.5 Kg.

Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guase internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with re enamel paint and fixed to wall with brackets complete with inernal charge. 6kg.Capacity

Providing and fixing mechanical foam type fire extingushers consisting of welded M.S. trolley mounted cylindrical body, squeeze lever discharge valve fitted with pressure discharge hose, discharge nozzle, trolley etc., ISI marked as per IS:IS:13386 finished externally with red enamel paint. Capacity 50 lit (D.G.Room)

Providing and fixing carbon-di-oxide fire extingushers trolley mounted with all accessories internal discharge tube,high pressure discharge hose,discharge nozzle, ISI marked as per IS:2878 finished externally with red enamel paint. Capacity 22.5 kg

5 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 5 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

10 LB capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 10 LB Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

Linear Pneumatic Heat detection tube with all necessary & supperts

Master Control Unit with Audio Visual Alarm with wiring to make complete system operational . The control Panel should have provision for integration with fire Alarm /SCAD/BMS System.

Supply, fixing, testing and commissioning of 1x40 Itr completele system with CCOE approved high pressure, seamless Cylinders having sutable 40 ltr water capacity & suitable to store Novec 1230 (FK5-1-12) gas at 34.5 bar pressure with valve assembly, low pressure supervisory switch for monitoring cylinder pressure gauge with safety burst disc safety cap, elbow and other accessories, mounting bracket, container straps, NRV. Electrically operated control head capable of being electrically operated from the fire detection & control, Pressure operated control head which shall allow for pressure actuation of gas mounted directly on top of cylinder valve, manually operated actuator to actuate the gas flooding process with the help of a lever, flexible rubber hose with wire bralded enforcment to route the gas from the storage cyinder to the discharge piping, to be connected to the discharge outlet of gas cylinder valve & to be terminated at the system piping or discharge manifold, Flexible actuation hose complete as required. Discharge nozzle, 180/360 degree. Designated to provide proper flow rate & distrbution Novec 1230 (FK5-1-12) gas to flood the hazard area as per requrement. Electrical non conductive,Novec 1230 (FK5-1-12) required as per NFPA 2001 latest eddition 4.5% Design Concentration. Piping ASTM grade A 106 schedule 40 with fittings & supports and Gas Release Panel compatible to Fire Alarm System.

Supply, fixing, testing and commissioning of 1x150 Itr completele system with CCOE approved high pressure, seamless Cylinders having sutable 150 ltr water capacity & suitable to store Novec 1230 (FK5-1-12) gas at 34.5 bar pressure with valve assembly, low pressure supervisory switch for monitoring cylinder pressure gauge with safety burst disc safety cap, elbow and other accessories, mounting bracket, container straps, NRV. Electrically operated control head capable of being electrically operated from the fire detection & control, Pressure operated control head which shall allow for pressure actuation of gas mounted directly on top of cylinder valve, manually operated actuator to actuate the gas flooding process with the help of a lever, flexible rubber hose with wire bralded enforcment to route the gas from the storage cyinder to the discharge piping, to be connected to the discharge outlet of gas cylinder valve & to be terminated at the system piping or discharge manifold, Flexible actuation hose complete as required. Discharge nozzle, 180/360 degree. Designated to provide proper flow rate & distrbution Novec 1230 (FK5-1-12) gas to flood the hazard area as per requrement. Electrical non conductive,Novec 1230 (FK5-1-12) required as per NFPA 2001 latest addition 4.7% Design Concentration. Piping ASTM grade A 106 schedule 40 with fittings & supports and Gas Release Panel compatible to Fire Alarm System.

Wiring for Light/Fan/Call Bell Point with 3X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete including 6 Amp flush type switch / bell push (Anchor Penta / Gold medal / Kolar kany Kom/ Havells or equivalent make as approved by department. GI/MS switch board (ISI Marked) with phenolic laminated sheet cover, ceiling rose etc complete. Short point upto 3.00 metre length.

Wiring for Light/Fan/Call Bell Point with 3X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete including 6 Amp flush type switch / bell push (Anchor Penta / Gold medal / Kolar kany Kom/ Havells or equivalent make as approved by department. GI/MS switch board (ISI Marked) with phenolic laminated sheet cover, ceiling rose etc complete. Medium point upto 6.00 metre length.

Wiring for Light/Fan/Call Bell Point with 3X1.5 sq.mm. P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe complete including 6 Amp flush type switch / bell push (Anchor Penta / Gold medal / Kolar kany Kom/ Havells or equivalent make as approved by department. GI/MS switch board (ISI Marked) with phenolic laminated sheet cover, ceiling rose etc complete. Long point upto 10.00 metre length.

Wiring for circuit wiring with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (finolex/RR Kabel/Nicco/Anchor or Equivalent make as approved by the Dept.) in surface/recessed ISI marked steel conduit pipe wiring system. with 3x1.5 sq.mm cable in 20 mm dia. Rigid Steel conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in ISI marked steel conduit pipe including earth continuity in surface/recessed conduit wiring system. With 2X2.5 sq.mm. + earth continuity with 1X1.5 sq.mm cable in 20 mm. dia. Rigid steel conduit.

Wiring for drawing sub-main line with P.V.C. insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel or equivalent make as approved by the Dept.) in ISI marked steel conduit pipe including earth continuity in surface/recessed conduit wiring system. With 2X4 sq.mm. + earth continuity with 1X2.5 sq.mm cable in 20 mm. dia. Rigid steel conduit.

Wiring for Drawing submain line with P.V.C insulated single core unsheathed industrial (multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/ RR Kabel or equivalent make as approved by the Dept. ) including earth continuity in surface/ recessed ISI marked steel conduit pipe wiring system. With 4X2.5 sq.mm. + earth continuity with 2X1.5 sq.mm cable in 25 mm. dia. Rigid steel conduit.

Wiring for Drawing submain line with P.V.C insulated single core unsheathed industrial (multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/ RR Kabel or equivalent make as approved by the Dept. ) including earth continuity in surface/ recessed ISI marked steel conduit pipe wiring system. With 4X4 sq.mm. + earth continuity with 2X2.5 sq.mm cable in 25 mm. dia. Rigid steel conduit.

Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed ISI marked steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. Short point upto 3.00 metre length.

Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed ISI marked steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. Medium point upto 6.00 metre length.

Wiring to 5 pin 6 Amps plug point with 1.5 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed ISI marked steel 20 mm. dia. conduit pipe wiring system including earth continuity with 1.5 sq. mm. cable to third pin of the plug socket etc. as required complete. Long point upto 10.00 metre length.

Wiring to 5/6 pin 16 Amps plug point with 4 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20mm. dia. steel conduit (AK G or equivalent as approved by the Dept.) Short point upto 3.00 metre length.

Wiring to 5/6 pin 16 Amps plug point with 4 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20mm. dia. steel conduit (AK G or equivalent as approved by the Dept.) Medium point upto 6.00 metre length.

Wiring to 5/6 pin 16 Amps plug point with 4 sq. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexuble bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system including earth continuity with 2.5 sq. mm cable to the 3rd pin of the socket as required complete with 20mm. dia. steel conduit (AK G or equivalent as approved by the Dept.) Long point upto 10.00 metre length.

Wiring for twin control light point with 1.5 sw. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe including 6 Amp flush type 2 way switch ( Anchor penta/Gold medal /Kolor Kany.Kom/Havells or equivalent make as approved by the dept.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover, ceiling rode etc complete. Medium point upto 6.00 metre length.

Wiring for twin control light point with 1.5 sw. mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex /RR kabel or equivalent make as approved by the Dept.) in surface/recessed conduit wiring system with 20mm dia rigid ISI marked steel conduit pipe including 6 Amp flush type 2 way switch ( Anchor penta/Gold medal /Kolor Kany.Kom/Havells or equivalent make as approved by the dept.) GI/MS switch board (ISI marked) with phenolic laminated sheet cover, ceiling rode etc complete. Long point upto 10.00 metre length.

Supplying and fixing 19 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in surface/recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 25 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 32 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 38 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing 50 mm dia ISI marked steel conduit pipe (AKG or equivalent as approved by the Dept.) in recessed including cutting the wall and making good the same ti its original architectural finish.

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 1-2 Module Type Metal

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 3 Module Type Metal

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 6 Module Type Metal

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 8 Module Type Metal

Supplying and fixing of following Metal Boxes for Model Range Legrand (Arteor), Anchor (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) in surface / recessed system complete as per direction of department. 12 Module Type Metal

Supplying including installation of socket outlet 6/10/13 Amps INTERNATIONAL SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 6 amp one way modular clip in bell push MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 16 amp one way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying with fitting and fixing of 6/10 amp two way modular clip in switch, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying fitting and fixing industrial plug & socket in surface mounted SPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of DP MCB complete with making necessary connection etc. as specified and directed by the Dept. 20A Capacity. (ABB, Schneider MG, legrand, Hager make)

Supplying fitting and fixing industrial plug & socket in surface mounted TPN sheet steel powder painted MCB DB incorporated with MCB DIN rail, neutral link Earth bar of the following rating of 4P MCB complete with making necessary connection etc. as specified and directed by the Dept. (ABB, Schneider MG, legrand, Hager make). 30/32A Capacity

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting SPN MCB DB incorporated with bus-bar, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make). 8 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting SPN MCB DB incorporated with bus-bar, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make). 12 way SPN double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting vertical per phase isolation (PP) DB incorporated with bus-bar 125A, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 6 way TPN (8+6+18) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting vertical per phase isolation (PP) DB incorporated with bus-bar 125A, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 8 way TPN (8+6+24) double door

Supplying with fitting and fixing sheet steel, phosphatised, powder painted dust & vermin proof Double door(IP-43) surface mounting vertical per phase isolation (PP) DB incorporated with bus-bar 125A, Neutral link, Earth Bar and din rail etc fitted on wall with grouting nuts & bolts as reqd. complete with making necessary connection as approved , specified & directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 12 way TPN (8+6+36) double door

Supplying with fitting and fixing single pole 10KA 240/415V 50Hz MCB of the following capacity complete with making necessay connection as approved, specified and directed by the Dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing single pole 10KA 240/415V 50Hz MCB of the following capacity complete with making necessay connection as approved, specified and directed by the Dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series -6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series -40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (Schneider MG, legrand, Hager, Crabtree Xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (Schneider MG, legrand, Hager, Crabtree Xpro make) C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (Schneider MG, legrand, Hager, Crabtree Xpro make) C Series - 63A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 30mA sensitivity DP RCCB - 25A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 30mA sensitivity DP RCCB - 40A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 30mA sensitivity DP RCCB - 63A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 100/300mA sensitivity DP RCCB- 25A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 100/300mA sensitivity DP RCCB- 40A

Supplying with fitting and fixing 30/100/300mA sensitivity 240/415V 50Hz DP RCCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( ABB, Schneider MG, legrand, Hager, Crabtree xpro make) 100/300mA sensitivity DP RCCB- 63A

Supplying with fitting and fixing Surge protector of max operation voltage 350V at 400 V network for maximum discharge current 40KA with operator indicator and draw out cartridge of (Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the dept. Surge protection Max operating voltage 340V Standard type- 1P+N

Supplying with fitting and fixing Surge protector of max operation voltage 350V at 400 V network for maximum discharge current 40KA with operator indicator and draw out cartridge of (Schneider or equivalent make), of the following ways complete with making necessary connection as approved, specified and directed by the dept. Surge protection Max operating voltage 340V Standard type- 3P+N

Supplying, installation of pre galvanised sheet steel std thickness 1.6mm under floor / ceiling trunking including necessary nuts & bolts, washer etc. as required, as directed and specified by the department. ( MK/ LEGRAND make) Size : - 100X38X1.6/1 compartment

Supplying, installation of pre galvanised sheet steel std thickness 1.6mm under floor / ceiling trunking including necessary nuts & bolts, washer etc. as required, as directed and specified by the department. ( MK/ LEGRAND make) Size : - 150X38X1.6/2 compartment

Supplying, installation of pre galvanised sheet steel std thickness 1.6mm under floor / ceiling trunking including necessary nuts & bolts, washer etc. as required, as directed and specified by the department. ( MK/ LEGRAND make) Size : - 225X38X1.6/3 compartment

Supplying, installation of pre galvanised sheet steel std thickness 1.6mm under floor / ceiling trunking including necessary nuts & bolts, washer etc. as required, as directed and specified by the department. ( MK/ LEGRAND make) Size : - 250X38X1.6/3 compartment

Supplying, installation of pre galvanised sheet steel std thickness 1.6mm under floor / ceiling trunking including necessary nuts & bolts, washer etc. as required, as directed and specified by the department. ( MK/ LEGRAND make) Size : - 300X38X1.6/3 compartment

JUNCTION BOX :- 150X150X60 - 75 mm Depth

JUNCTION BOX :- 250X250X60 - 75 mm Depth

JUNCTION BOX :- 300X300X60 - 75 mm Depth

JUNCTION BOX :- 350X350X60 - 75 mm Depth

JOINT SLEEVE :- 100/1/6 FOR 38mm

JOINT SLEEVE :- 150/2/6 FOR 38mm

JOINT SLEEVE :- 225/3/6 FOR 38mm

JOINT SLEEVE :- 250/3/6 FOR 38mm

JOINT SLEEVE :- 300/3/6 FOR 38mm

Cross over/ Junction box :- Cross over 250X250X60 - 75mm 3 compartments

Cross over/ Junction box :- Cross over 300X300X60 - 75mm 3 compartments

Cross over/ Junction box :- Cross over 350X350X60 - 75mm 3 compartments

Supplying including fitting and fixing of TV SOCKET, MODEL RANGE LEGRAND (ARTEOR), ANCHOR (AVE), MK (BLENZE), SCHNEIDER (ZENSELO), CRABTREE (MURANO) including making necessary connections as per direction of department.

Supplying including fitting and fixing of following star rated A.C. ceiling fan complete with all accessories like down rod, canopy etc of following sweeps with making necessary connection cable as approved by Deptt.s etc as required complete and as directed by the department as required complete etc. (Without regulator). Energy efficient 5-star 1200 mm sweep. (Orient / PSPO / Usha / Crompton / Havells/ ATC / V Gaurd.)

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series- 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series- 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series- 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series- 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series- 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series- 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 63A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series- 6 to 32A

Supplying with fitting and fixing DP 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. (ABB, Schneider MG, legrand, Hager, Crabtree xpro make) C Series- 40A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, spcified and directed by the dept. ( Schneider MG, legrand, Hager, Crabtree xpro make) C Series - 6 to 32A

Design & Supply of IP-55 Rising Mains with plug-outlets in every 850mm on both side of trunking of following capacity with Aluminium conductor, TPN with 100% neutral, 1000V IP-55, 50 hz, housing made from 1.5mm hot-galvanized sheet steel treated according to UNI 10327 and painted with RAL 7035 resins with high resistance to chemical agents including End cover, supports and two runs of GI earth bar and complying with IEC-60439. (Legrand/C&S or equivalent as approved by the deptt.) 1250 amp Rising Mains (SC Rating for 1 Sec-75 KA.)

Design & Supply of IP-55 Rising Mains with plug-outlets in every 850mm on both side of trunking of following capacity with Aluminium conductor, TPN with 100% neutral, 1000V IP-55, 50 hz, housing made from 1.5mm hot-galvanized sheet steel treated according to UNI 10327 and painted with RAL 7035 resins with high resistance to chemical agents including End cover, supports and two runs of GI earth bar and complying with IEC-60439. (Legrand/C&S or equivalent as approved by the deptt.) 400 amp Rising Mains (SC Rating for 1 Sec-25 KA.)

Supply of following capacity End Feed Unit Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 1250 amp End Feed Unit (W/O MCCB)

Supply of following capacity End Feed Unit Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 400 amp End Feed Unit (W/O MCCB)

Supply of following capacity TPN Tap off box Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 63 A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

Supply of following capacity TPN Tap off box Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 100 A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

Supply of following capacity TPN Tap off box Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 160 A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

Supply of following capacity TPN Tap off box Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 250A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

Supply of following capacity TPN Tap off box Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 400A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (W/o MCCB.)

Supplying with fitting & fixing panel mounting open execution 415V 50Hz 4P MCCB with microprocessor Release (Ics=Icu, adjustable over Load and Short Circuit setting, neutral adjustable with earth fault protection without enclosure of the following capacity complete with making necessary connection as approved, specified and directed by the dept. 36KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 63A

50KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 100A

50KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 160A

50KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 250A

50KA ( ABB, Schneider MG, legrand, Hager C&S, L&T, Siemens make) 400A

MAIN & SUB MAIN CABLES Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-2 (A2XWay, A2XFaY) 6 sq.mm two core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-2 (A2XWay, A2XFaY) 10 sq.mm two core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) 35 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) 50 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) 70 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) 95 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) 120 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) 185 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) 240 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-3.5 (A2XFY) 300 sq.mm 3 and 1/2 core armoured cable

Supply and laying of following size solid aluminium conductor up to 10 sq.mm balance stranded conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured /armour (Aluminium for single core up to 70 sq.mm balance Aluminium strip, Galvanized for cables up to 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm balance all galvanized steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) Core-4 (A2XWY, A2XFY) 25 sq.mm four core armoured cable

Supply and laying of following size power / control copper cables, solid copper conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/armoured (Galvanised for cable up to 10x1.5 sq.mm, 8x2.5 sq.mm, 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm, balance all all galvanised steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) 4 Core-4, 2XWY, 2XFY- 4 sq.mm four core armoured cable

Supply and laying of following size power / control copper cables, solid copper conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/armoured (Galvanised for cable up to 10x1.5 sq.mm, 8x2.5 sq.mm, 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm, balance all all galvanised steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) 4 Core-4, 2XWY, 2XFY- 6 sq.mm four core armoured cable

Supply and laying of following size power / control copper cables, solid copper conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/armoured (Galvanised for cable up to 10x1.5 sq.mm, 8x2.5 sq.mm, 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm, balance all all galvanised steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) 4 Core-4, 2XWY, 2XFY- 10 sq.mm four core armoured cable

Supply and laying of following size power / control copper cables, solid copper conductor, XLPE Insulated, cores laid up, PVC tape inner sheathed, unarmoured/armoured (Galvanised for cable up to 10x1.5 sq.mm, 8x2.5 sq.mm, 2x10 sq.mm, 3x10 sq.mm, 4x6 sq.mm, balance all all galvanised steel strip), extruded PVC ST2 sheathed, 650/1100 V grade as per IS 7098 (Part1) 1988, laid in air or through existing cable trench / duct / cable tray / HDPE pipe including fitting required size of lugs at the both end of the cable by using crimping tool and making good damaged done as specified and directed by the department. (Nicco / Havells / RPG / CCI / Polycab / Gloster / Finolex make or equivalent.) 4 Core-4, 2XWY, 2XFY- 16 sq.mm four core armoured cable

Supplying Fitting and Fixing of (Dowells / Commet make) Double compression brass gland with nickel. Weatherproof (CBW) Size:8-10, 3/4''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1-1/8''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1-1/4''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1-3/8''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1-1/2''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:1-3/4''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:2-1/4''

Supplying Fitting and Fixing of (Dowells / Commet make) Single compression brass gland heavy duty. Single Compression Brass Gland Heavy Duty. Size:2-3/4''

Supplying, Fitting and fixing of occupany sensor of the following atageories as per required and directed by the department. (ABB/ Panasonic/ mk/ anchor/ crabtree/ Hager/ Panasonic or equivalent make as approved by deptt. Indoor presence detection with 360 degrees angle of detection and 2 relays (one for light and one for HVAC), range up to 7 meter at 2.5 meter ceiling height.

Supply, installation, testing and commissioning of following LAN networks equipments. Solid Copper Cable 6, 4 pair, UTP 305m SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Patch Panel Cat 6 UTP Keystone-24 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Patch Cord Cat 6 UTP Gray 1m- Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation, testing and commissioning of following LAN networks equipments. Cat 6 Keystone UTP Jack with Dust Cover-White SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Back Box-(Surface Mount Box) For Single and Dual SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

APW Cyber Rack Networking Equipment Rack APW President Enclosure, 600mmW CYBERACK 42U/800mmD (CRCA Steel Frame with Aluminium Profiles & 2 Nos. of Removable Side Panels with followwing items:- Top cover with cable entry-1no.-Bottom cover with cable entry-1no.-19" Mounting Angles-2 pairs., Finish: Powder coated to 80 microns; Matt Finish. Colour: BLACK with, Load rating capacity -500 Kgs., Front side vented glass door and rear full perforated steel door with locks. " PDU 10*5/15A-01 Nos., Fan Housing Unit with 4 Fans-01 Set, Mounting Hardware (Set of 20)-1 Set, Castor with Brake- 2Nos., Castor without Brake - 2 Nos., Earthing Kit - 01 Set, Cable Manager 19" 1U - 2 Nos.

Patch Cord Cat 6 UTP Gray 2m- Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation, testing and commissioning of following LAN networks equipments. Solid Copper Cable 6, 4 pair, UTP SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Patch Panel Cat 6 UTP Keystone-24 Port- Loaded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Patch Cord Cat 6 UTP Gray 1m- Moulded SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt..

Supply, installation, testing and commissioning of following LAN networks equipments. Cat 6 Keystone UTP Jack with Dust Cover-White SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

Supply, installation, testing and commissioning of following LAN networks equipments. Back Box-(Surface Mount Box) For Single and Dual SCHNEIDER/LEGRAND or equivalent make as approved by the Deptt.

APW Cyber Rack Networking Equipment Rack APW President Enclosure, 600mmW CYBERACK 42U/800mmD (CRCA Steel Frame with Aluminium Profiles & 2 Nos. of Removable Side Panels with followwing items:- Top cover with cable entry-1no.-Bottom cover with cable entry-1no.-19" Mounting Angles-2 pairs., Finish: Powder coated to 80 microns; Matt Finish. Colour: BLACK with, Load rating capacity -500 Kgs., Front side vented glass door and rear full perforated steel door with locks. " PDU 10*5/15A-01 Nos., Fan Housing Unit with 4 Fans-01 Set, Mounting Hardware (Set of 20)-1 Set, Castor with Brake- 2Nos., Castor without Brake - 2 Nos., Earthing Kit - 01 Set, Cable Manager 19" 1U - 2 Nos.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supply, erection, testing and commissioning of following sizes of splitter of aluminium die cast body in suitable size of G.I. Box. 6 way

Supply, erection, testing and commissioning of following sizes of splitter of aluminium die cast body in suitable size of G.I. Box. 8 way

Supply of following capacity End Feed Unit Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 2500 amp End Feed Unit (with 2500A TPN MDO ACB)

Supply of following capacity TPN Tap off box Made of 1.6 mm thick sheet steel enclosure dully painted with powder coating to existing rising mains complete with provision of fixing MCCB. (Legrand/C&S or equivalent as approved by the deptt.) 630A Tap-off Box with inbuilt Disconnection. (Legrand/C&S or equivalent as approved by the deptt.) on cover (with 630A MCCB.)

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 2500 A 50kA SC for 1 sec

Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor FRLS insulated cable including termination complete as required in existing cable tray. 1C x 95 sq.mm PVC Insulated cu wire including end termination.

Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor FRLS insulated cable including termination complete as required in existing cable tray. 1C x 25 sq.mm PVC Insulated cu wire including end termination.

Supply & Laying of following sizes of 1.1KV grade multistranded copper conductor FRLS insulated cable including termination complete as required in existing cable tray. 1C x 16 sq.mm PVC Insulated cu wire including end termination.

Supply, Installation, Testing & Commissioning of Earthing Junction Box size - 400mm x 300mm x 80mm made out of 16 SWG CRCA sheet with seven tank process & powder coating, earthing link (32mmx6mm copper strip), front door with glass as complete as required.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm wide x 50 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm wide x 50 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm wide x 50 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Tee" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 100 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 150 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 300 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 450 mm wide x 50 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "Cross member"(galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc as required. 900 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 100 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 150 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 300 mm wide x 50 mm depth x 1.6 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 450 mm wide x 50 mm depth x 2.0 mm thickness.

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 600 mm width X 50 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 750 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray “Reducer” (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. 900 mm width X 62.5 mm depth X 2.0 mm thickness

Supply, Installation, Testing & Commissioning of Recess LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, 1000 - 1200 lumen, Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 1000-1200.Philips DN193B LED12S-6500 PSU WH S1 or equivalent.

Supply, Installation, Testing & commissioning of Recess LED Downlighter made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, 1600 - 1800 Lumen, Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80, PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 1000.Philips DN 192B LED9S-6500 PSU WH or equivalent.

Supply, Installation, Testing & Commissioning of 12 watt LED Mirror Light as complete as required. (Philips Make, Cat No - Mirror Light 32047/11 or equivalent.)

Supply, Installation, Testing & Commissioning of Surface Mounted Linear LED IP65 fitting made of Virgin Polycarbonate housing & Non Yellowing PC Diffuser ,LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, Life of fixture (Including Driver) : 50K Hrs. @ L70B50 Lumen maintenance, CCT 6500 (SDCM<5), CRI >80 , PF >0.95 & THD<10%, an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 3KV The fixture design should comply with IS10322, EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598,Minimum system Lumens 4000. Philips WT201C LED40S-6500 PSU L120 or equivalent.

Supply, Installation, Testing & Commissioning of Recess LED 600x600mm fitting made of white CRCA powder quoted finish with fully covered by PMMA Acrylic Lumio Diffuser, LED Used shall be SMD type and fixture should have minimum efficacy at System level >=100lumens/watt, Life of fixture : 50K Hrs. @ L70B50 Lumen maintenance, CCT up to 6500 (SDCM<5), CRI >80 , PF >0.95 & THD<10%, Fixture must be office compliant & have to comply to UGR<19 value for optimim glare.an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.5KV The fixture design should comply with IS:10322 & Must be EMC / EMI compliance maintaining driver leakage current as per as per IEC 60598, Minimum system Lumens 3000. Philips RC380B LED30S -6500 G4 L60 W60 PSU OD OC LED Office Compliant Panel with Min Glare Value i.e UGR<19 or equivalent.

Supply, Installation, Testing & Commissioning of LED Bulkhead Fixture made of pressure die cast aluminum housing with high efficiency reflector, LED Used shall be SMD type and fixture should have minimum efficacy at System level (Not Chip Level) >=100lumens/watt, Life of fixture (Including Driver) : 30K Hrs. @ L70B50 Lumen maintenance, CCT - 6500 (SDCM<5), CRI >70, PF >0.95 , an operating Voltage Range of 140 - 270 V.Minimum Internal Surge Protection 2.0KV The fixture design should comply with IS10322, Minimum system Lumens 700.Philips WT140W LED7S-CW PSU S1 PC LED Bulkhead or equivalent.

Supply, Installation, Testing & Commissioning of Self contained emergency light units 1x9 watt double sided for wall / ceiling mounting with suspension / mounting kit, lamps, inbuilt standby battery (for 2 hours backup) and battery charger etc. in suitable enclosure. Make - Prolite or equivalent.

Supply, installation, Testing & Commissioning of 18-22W Watt, surface Type, 6500K, LED batten light fixture, having minimum system lumen output of 100 Lumen / watt complete as requried. (Make : Philips Cat. No. BN021C LED20S PSU CW GR S2 )

Supply, Installation, Testing & Commissioning of LED 46W Light recess mounted downlight with high efficiency electronic driver. (Make Philips Cat No- RS271B LED40/830 PSU-E WB WH or equivalent.)

Supply, Installation, Testing & Commissioning of Electronic Buzzer as complete as required.

Supply, Installation, Testing & Commissioning of Recessed Foot Light as complete as required. (Philips Make - Philips 30974 Foot Light' or equivalent.

Supply, Installation, Testing & Commissioning of 12W Surface mouted LED Downlight as complete as required. (Philips Make - Philips Cat. No. SM250C LED12S- 6500 PSU WH' or equivalent.

Supply , Installtion , Testing and comissioning of 27U wall mount rack with fans , 2 cable managers, satationary shelf , 2 Nos of hardware pkts. Approved Makes: Poweride/MTS/Rittal/APC/APW

Supply , Installtion , Testing and comissioning of armoured 6 core multimode OFC cable for interfloor switch connectivity.

Supply , Installtion , Testing and comissioning of 6 port loaded LIU with adaptor plates , pigtel cables for connections.

Supply , Installtion , Testing and comissioning of 24 port loaded LIU for core switch to access switch connectivity over fiber.

Supply , Installtion , Testing and comissioning of SC-SC multimode fiber patch cord.

Supply 8 mm round aluminium conductor for horizontal lightning protection - run in roof. Model : AL8. Make : Hakel / APS

Supply of roof conductor holder for 8 mm round aluminium conductor made of Gun Metal for horizontal installation. The distance between each holder should be min of 1.5 mtr. Model : APSRCS50. Make : Hakel / APS

Supply of Cross connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS

Supply of T connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS

Supply of L connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCCRC50 , Make : Hakel /APS

Supply of straight connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSPCRC50, Make : Hakel / APS

Supply of Expansion piece to compensate the expansion of round 8 mm Al conductor when temperature variation . Connection should be in every 20 mtr. Model : APSEXP50 , Make : Hakel/APS

Supply of fixing glue for fixing of roof conductor holder .

Supply of Expansion piece connector for connecting of 8 mm Al round conductor . The connector should be of Gun Metal with SS nuts and bolt. Model : APSCEP50- Make : Hakel /APS

DOWN CONDUCTOR AS PER IEC 62305 Supply of 8 mm round aluminium conductor as a down conductor mounted in the surface of wall which will carry the lightning current to earth pit. Model : AL8. Make : Hakel / APS

Supply of Down conductor holder for 8 mm round aluminium conductor of min distance between the wall to the conductor will be of 50 mm. The distance between each holder should be min of 1.5 mtr. Model : APSRCH50 Make : Hakel /APS

Supply of Test Joint Point for 8 mm round aluminium conductor , the size should be of 25 x 3 x 150 mm copper in ABS boxes. Model : APSTLBCU. Make : Hakel / APS

EARTHING AS PER IEC 62561- 2 & 7 Supply of UL approved low carbon high tensile steel rod with copper coating of min 254 micron JK Chemrode - 317 CBR the dia should be 17.2 mm with length of 10 feet ( 3000 mm) . The rod shall be as per IEC 62561-2 and approved by UL 467. The rod shall be tested from NABL lab for current discharge not less then 46kA peak. The Chemrode shall be surrounded with 50 kg ( 2 bag) of Earth enhance materiel JK Activer+ according to IEC 62561-7 and the Chemical resistance value shall not increase more then 0.064 Ωm and same will be tested from NABL lab. Make :APS/JK

Supply, Installation,Testing & Commisioning of Microprocessor based X loop fire alarm control panel EN approved expandable upto 12 loops fully networkable with each loop capable of taking 125 devices, 4 line x 40 character alpha-numeric liquid crystal display .The panel shall be soft addressable type . The panel shall be able to give pin point location of all fire/fault conditions. Further, the panel must be able to automatically switch off respective control switches when ever any alarm is triggered. The panel shall have in built rectifier, Loop cards,provision for externel & internal printer(if required), L C D unit to indicate Fire/Fault Signal with address and analog output, built in printer to log all fire or fault events complete in all respects, integral SMF lead acid batteries with sealed cells of 24 V capable of running for a minimum of 8 hours with integral battery charger complete as required and as per specification. The fire alarm panel shall be suitable for software integration with BMS & PA system. 10 Loops

Supply, Installation,Testing & Commisioning of Fire Graphics Software to be loaded on PC to monitor the Floor wise Fire Detection System.

Supply, Installation,Testing & Commisioning of Networkable Repeater Panel (LCD indicator panel) with 2 line X 20 characters alpha numeric LCD display with all commands such as reset, mute, silence with suitable battery backup complete as required.

Supply, Installation,Testing & Commisioning of Analog Addressable Intelligent multisensor detector with two inbuilt optical smoke sensors with light angles as well as additional heat detector sensor with decentralise intelligence, soft addressable Photothermal type with inbuilt fault isolator as per NFPA style 7 wiring complete with base as required.

Supply Installation, Testing & Commissioning of Intelligent addressable photothermal detector with blue colour LED for very early warning with inbuilt isolator as per NFPA7 style 7 wiring & standard base complete as per specification.

Supply, Installation, Testing & Commisioning of Analogue Addressable Intelligent Heat Detector with fixed & rate of rise temperature function with decentralise intelligence , soft addressable type, with inbuilt fault isolator as per NFPA style 7 wiring complete with base as required.

Supply Installation, Testing & Commissioning of Intelligent addressable Manual Call Point / Pull station complete as per specification.

Supply, installation, testing and commissioning of addressable control module complete as per specification.

Supply, installation, testing and commissioning of addressable monitor module complete as per specification.

Supply Installation, Testing & Commissioning of wall mounting loop powered addressable type hooter with all accessories.

Supply Installation, Testing & Commissioning of Response Indicator.

Supply Installation, Testing & Commissioning of fire fighter main console at control room including power supply and accessories.

Supply Installation, Testing & Commissioning of Fire fighters telephone handset.

Supply Installation, Testing & Commissioning of Fire fighters telephone jack.

SITC of 2x250W Class-D Amplifier with 4 independent channels and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection. Approved Makes : Bosch Praesedio / Honeywell - X618/ Ateis - IDA

SITC of Network Resource Interface, 4 channels network audio source, 32 dry contacts in and 8 try contacts out for Fire Alarm Interface

SITC of 6W Ceiling mount with max SPL1M/1W 96dB . Frequency response of 160Hz-20KHz. The speaker shoud have tappings at 6W/3W

SITC of 6W Wall mount with max SPL1M/1W 96dB . Frequency response of 160Hz-20KHz. The speaker shoud have tappings at 6W/3W.

Supply, Installation, Testing & Commissioning of 2C x 1.5 sq.mm Fire Survival unarmoured cable (300/500V) with Class-2 Copper conductor having Mineral ceramic glass fire barrier tape covered by an extruded layer of Cross-linkable Low Smoke Zero Halogen (LSZH) insulation as per EI-5 Of BS EN 50363 along with ATC drain wire, aluminium tape screening and LSZH outer sheath as per BS 7629-1 & BS-5839-1 (latest edition). Outer sheath should be Anti Rodent/Anti Termite. Should retain circuit integrity as per BS 8434-2 (930 deg C for 120 mins on single sample) including end termination etc as complete as required. (For Fire & PA System)

CCTV SYSTEM Supply, Installation, Testing and Commissioning of UL Listed , ONVIF profile S & G , 1/2.8" CMOS, IP Vari Focal Dome Camera , Full, HD 3 MP , 2.8-12 mm Motorized Varifocal Lens, 30 FPS , Triple Stream with Edge Based Analytics , True Day/Night with IR Cut Filter with auto switch , Shutter Speed 1/5s ~ 1/20,000 s, IR Illuminator 30 Meter Min Effective Range, 120DB Wide Dynamic Range, Alarm 1/1, Audio 1/1, SD Card, H.265, H264 Compression, PoE, IP66 , Vandal Proof IK10 etc. Approved Makes: Allgovision/ Pelco/ Avigilon/ Impulse/ Axis.

Supply, installation, testing and commissioning of UL Listed , ONVIF profile S & G ,1/2.8" CMOS, IP Vari Focal Bullet Camera , Full, HD 3 MP Resolution , 2.8-12 mm Motorized Varifocal Lens , 30 FPS , Triple Stream with Edge Based Analytics , True Day/Night with IR Cut Filter with auto switch , Shutter Speed 1/5s ~ 1/20,000 s, IR Illuminator 30 Meter Min Effective Range, 120DB Wide Dynamic Range, Alarm 1/1, Audio 1/1, SD Card, H.265, H264 Compression, PoE, IP66 etc. Approved Makes: Allgovision/ Pelco/ Avigilon / Impulse/ Axis.

Supply, installation, Testing and Commissioning of Open Platform ONVIF profile S &G Network Video Recorder 32 channel, Intel based, Full Rack, RAID 0/1/5/10, @ 2M/30FPS, 1*2.5" SATA + 8 * 3.5" SATA, Throughput: 640 Mbps.1 X HDMI , 1X VGA ,, 1 X mic in , 1 X line out , USB 3.0 x 2 + USB 2.0 x 3 , 1 X WAN port , 1 X LAN port , pre-installed VMS :Approved Makes :Allgovision/ Pelco/ Avigilon / Impulse/ Axis.

Supply, Installation, Testing & Commissioning of Core Switch with switching capacity of 1.4Tbps, forwarding performance of 1Bpps with 32x 1/10G SFP+ ports plus 4x 40G QSFP+ ports from day 1, dual hot swappable internal power supply, 60K IPv6 routes and 48K IPv6 multicast routes. Should support advance layer 3 (RIPng, OSPF, BGP and MPLS) with 1 year support. Stack Module/40 Gig Optics and all other Cables should be included in Day 1. Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista

Supply, Installation, Testing & Commissioning of 24 Port POE+ Access Switches with switching capaticy of 128 Gbps, forwarding performance 95 Mpps, having 24 x 10/100/1000BASE-T PoE-plus(RJ45) with minimum PoE budget of 370W and 4x 10G SFP+ uplink ports . Should support min 2GB internal DRAM, 2GB internal Flash memory,32K MAC address, 1K IPv6 Multicast Routes, Should have static Routes from day 1.One year support. Approved Make : Cisco/ Impulse / Juniper / Extreme/ Arista

Supply, Installation, Testing & Commissioning of 4TB HD Approved Makes: WD, Segate / Toshiba.

Supply, Installation, Testing and Commissioning of Full HD 65" LED Professional Display Panel. Approved Makes: Panasonic, Sony, Samsung.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); Memory: 4GB, NON-ECC, 1600MHZ; RAM: 4GB (1x4GB) Non-ECC DDR3 1600MHz SDRAM Memory; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; 20" TFT Monitor; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit. Approved Makes: HP, Dell, IBM.

UPS SYSTEM Supply, Installation, Testing & Commissioing of 140 KVA UPS in paralleling mode at 0.99 input power factor with SNMP card, compatible for BMS connectivity on backnet/MODBUS, Isolation transformer as per specification given in the document with following broad features. THD(i) shall be less than 3% in the entire loading range. UPS shall carry design output at 40 deg. Shall have soft start and hold of for incoming supply. Invertor capability to supply 150% load for 5 sec. Three Phase Input and Three Phase Output. (Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. Battery shall be external type with rack and suitable for 30 minute backup on 100% load. UPS shall be compatible for 4 nos unit in parallel operation. (Synchronize). Parallel operation kit shall be supplied with UPS. Suitable size & length of Copper Cable between battery to battery and battery to UPS shall be provided without any extra cost. UPS described as above

Supply, installation, testing & commissioing of 30 KVA UPS at 0.99 input power factor with SNMP card, compatible for BMS connectivity on backnet/MODBUS, inbuilt isolation transformer as per specification given in the document with following broad features. a) THD(i) shall be less than 3% in the entire loading range. b) UPS shall carry design output at 40 deg. c) Shall have soft start and hold of for incoming supply. d) Invertor capability to supply 150% load for 5 sec. e) Three Phase Input and Three Phase Output. (Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.) f) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. g) Battery shall be external type with rack and suitable for 30 minute backup on 100% load. Suitable size & length of Copper Cable between battery to battery and battery to UPS shall be provided without any extra cost. UPS described as above

Supply, installation, testing & commissioing of 40 KVA UPS at 0.99 input power factor with SNMP card, compatible for BMS connectivity on backnet/MODBUS, inbuilt isolation transformer as per specification given in the document with following broad features. a)THD(i) shall be less than 3% in the entire loading range. b) UPS shall carry design output at 40 deg. c) Shall have soft start and hold of for incoming supply. d) Invertor capability to supply 150% load for 5 sec. e) Three Phase Input and Three Phase Output. (Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire. f) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. g) Battery shall be external type with rack and suitable for 30 minute backup on 100% load. Suitable size & length of Copper Cable between battery to battery and battery to UPS shall be provided without any extra cost. UPS described as above

Supply, installation, testing & commissioing of 30 KVA UPS at 0.99 input power factor with SNMP card, compatible for BMS connectivity on backnet/MODBUS, inbuilt isolation transformer as per specification given in the document with following broad features. a) THD(i) shall be less than 3% in the entire loading range. b) UPS shall carry design output at 40 deg. c) Shall have soft start and hold of for incoming supply. d) Invertor capability to supply 150% load for 5 sec. e) Three Phase Input and Three Phase Output. (Input - 340V - 470V, Three Phase, 4 wire. / Output - 400-415 Volt, Three Phase, 4 Wire.) f) Shall not allow deep discharge of the battery and shall not go to 10.5 volts in case of 12 volt cells. g) Battery shall be external type with rack and suitable for 90 minute backup on 100% load. Suitable size & length of Copper Cable between battery to battery and battery to UPS shall be provided without any extra cost. UPS described as above

DUM WEIGHTER- Design, manufacturing, testing at works, supply and delivery, receiving, unloading, storing, inspection, handling, assembling, installing in correct assigned position, effecting proper connections, testing and commissioning of following capacity Dum weighter, having speed of 0.5 MPS 4 stops and 4 openings and total travel of 17.2 meters approx. with VVVF drive, full collective Simplex / Duplex control on 415 V, 50 cycles, 3 phase power complete in accordance with specifications and drawings as required with Car, Car Door & Hoistway Door in SS Hairline, inclusive of built in ARD and as per specification. 250 Kg

Fabricating and supply, Installation, Testing & Commissioning of 6.0 metre long M.S. Ribbed steel tubular pole having 3 steps. Bottom portion shall be 2 metre long having outer dia 140 mm of thickness 4.0 mm, middle portion shall be 2.5 mm long having outer dia 114.0 mm with thickness of pipe 3.0 mm and top portion shall be 1.46 metre long having outer dia 89.0 mm with thickness of pipe 3.0 mm including providing and fixing MS plate 450mm x 450mm x 10mm, drilling holes for earthing and wire entry etc. as required. The pole shall be with in built cable loop-in box including 10/20 A SP MCB, terminal block earth stud, 0.75 / 1 meter long arm etc. The diameter of arm shall be suitable for light fixture installation. The pole shall be PU painted with 90 micron thick of approved colour.

Supply, Receiving, Unloading, Shifting, Installation, Testing & commissioning of Bollard Light 170 mm dia, 780 mm height made out of cast aluminium lighting fixture, glass diffuser, stainless steel screw, extruded aluminium poles, corrossion & UV resistant coation of 1 x 18 watt.

Supply, Receiving, Unloading, Shifting, Installation, Testing & commissioning of Bollard Light 120 mm dia, 1000 mm height made out of cast aluminium lighting fixture, glass diffuser, stainless steel screw, extruded aluminium poles, corrossion & UV resistant coation of 1 x 18 watt.

Supply, Installation, Testing & Commissioning of LED street light fixture 45 watt, clour cool white , integral driver, protection IP 65, CLASS I as complete as required. (Make Philips, Cat No- Greenline or equivalent)

Supply, Installation, Testing & Commissioning of Controllers- Networkable 2 reader/ 2 door Intelligent controller with enclosure and power supply (Enclosure + Power Supply) .Approved Makes:/Avigilon/HID/Honeywell

Supply, installation, testing and commissioning Short Range (up to 9 cm ) Smart Card Reader For Exit of Lift Access Doors , tripod/Flap barrier- Entry & Exit (doors) as per the specification. Approved Makes:/Avigilon/HID/Honeywell.

Supply, installation, testing and commissioning of contactless Clamshell 2K /2Application Area Smart Card suitable for Access Door as per the specification. Approved Makes:/Avigilon/HID/Honeywell.

Supply, installation, testing and commissioning Access Control System Server Software consisting of Access Control system , Alarm Document , Alarm management , All these along with high end security features consist in single package as per specification. Approved Makes:/Avigilon/HID/Honeywell.

Supply, Installation, testing & commissioning of Single Leaf Electro Magnetic Lock of Suitable Capacity(Min 600 lbs) as per specification .Approved Makes:/Avigilon/HID/Honeywell. Double Leaf Door

Supply, Installation, testing & commissioning of Single Leaf Electro Magnetic Lock of Suitable Capacity(Min 600 lbs) as per specification .Approved Makes:/Avigilon/HID/Honeywell. Single Door Leaf

Supply and Laying of of 8 Core x 0.2 sq mm multi strand, copper, unarmored shielded Cable as per specification (between the every card readers & the access controllers)

Power Supply- Supply, Installation , testing and commissioning of 12 V SMPS DC Power Supply Unit, highly regulated and spikes free terminal voltage and heavy sourcing current for regulated terminal voltage.

Magnetic Contact- Supply, Installation, Testing and commissioning of Magnetic Contact.Approved Makes:/Avigilon/HID/Honeywell

Supply , Installation , Testing and commissioning of Single Front Facia Plate consisting of Soft Touch Push Buttons Emergency Exit Door Release and indicator LED to show the door status .Approved Makes:/Avigilon/HID/Honeywell

NURSE CALL SYSTEM VDE 0834 certified/ approved System Switch: S.I.T.C. of Main Controller system switch that forms a decentralised communications node for exchanging data between the connected system devices and the rest of the communications system, consisting of 1 x RJ45 socket, 100Mb IP Port (IEEE802.3 100BaseTX), galvanically isolated conforming to EN 60950 and VDE 0834, 7 x RJ45 sockets, each for a 100Mb IP system port (IEEE802.3 100 BaseTX) for connecting all IP capable system modules, 1 x RJ45 socket, 100Mb IP Port (IEEE802.3 100BaseTX) for connecting communications, staff and ward terminals as well as control panel PCs or for redundant Connection, Control LEDs for indicating the current operating state, 2 x RJ45 sockets for connection of the external data bus, all IP system modules supplied with power using Power over LAN technology using its own communication LAN complete as required.

VDE 0834 certified/ approved Nurse Station Terminal: S.I.T.C. of Nurse Station Ward Terminal comprises of 5.6 “LC display for displaying all details, a smash proof glass panel (to protect the sensitive display from unnecessary contact during cleaning and other processes) , function keys for operating the system, Querying receiver for speaking discretely, Microphone and loudspeaker for hands-free speech (incl. volume control), automatic changeover between hands-free and discrete speaking , Electronic circuit board with controller and FlashProm, 100BaseTX interface to the system switch, 2.8m connection cable with an RJ45 connection plug, which is protected, from disconnection, for connecting to a connection module. The ward terminal shall display date and time, indication of all presence, all set reminedrs, indication of all calls in accordance with VDE0834. All call indications follow the priority and must display the exact location of the calls. The ward terminal shall be provided along with suitable connection module & back box. It should be supplied along with connection module & its back box for installation complete as required.

VDE 0834 certified/ approved Call - Cancel Button S.I.T.C. of Call Cancel buttons having anti microbial additives that reduces the risk of bacterias,viruses and fungus being transmitted , with 1 call button (red) including a finder light / reassurance light, 1 presence button (green) incl. control LED,Moisture protected call-cancel button complete as required.

VDE 0834 certified/ approved Lamp Module S.I.T.C. of Lamp module having minimumfour light chamber with light refelectors for homogeneous illumination strips-1 light chamber with 3 ultra bright red LEDs,1 light chamber fitted with 3 ultra bright white LEDs, 1 light chamber fitted with 3 ultra bright green LEDs, 1 light chamber fitted with 3 ultra bright blue LEDs, that uses to signal the optical indication of calls presences and reminders in the relevant colours informations so that it can be seen from a distance.The system shall be conforming to VDE0834 and shall conforms to the light strength set out by VDE0834, with LED life expectancy minimum 100,000 operating hours approximately complete as required.

Central Monitoring & Even Database Software with Server & LAN switches Even Database Software S.I.T.C. of Software pack installed on the system server for automatically logging all events in the entire communications system, such as, e.g., calls, presence markings, call acknowledgements, reminders complete as required.

Server for Nurse Call System S.I.T.C. of Server for Nurse Call System: Uploading the firmware and the system configuration, for logging of all system events and as a central location for system configuration and remote maintenance. The minimum requirements for the server are as follows:- Intel Xeon E3 2,3GHz or similar - 2 GB RAM - 1 x 160GB HDD - 1 x DVD harddrive, 2 x Gbit LAN Ethernet RJ45 - 1 x serial connection RS232 and 2 x USBV2.0, 1 x PCI or 1 x PICe socket - support for SUSE Linux enterprise Server from V.11-SP1, complete as required.

S.I.T.C. of Backbone Switch consisting of Uplink connections: 2 x 1Gb uplink ports, RJ45 (GBIC capable, possibility for LWL), Connections downlink: 24 x 100Mb downlink ports, RJ45 Switch complete as required.

AHRI Certified 450 TR Centrifugal Water Cooled Chilling Machine With Air Cooled Variable Speed Drive & Microprocessor Based Control Panel (Capacity of Chiller as given below) Supply, installation, testing and commissioning of Centrifugal Water Cooled Water Chilling M/C of actual capacity at below mentioned operating conditions with R - 134 A refrigerant, open / semihermatic / hermatically sealed centrifugal compressor, direct / gear driven by suitable KW Sq. Cage induction motor complete with variable speed drive, even pass water-cooled shell & tube condenser, even pass insulated shell and tube flooded chiller, flow switches at condenser & chiller outlet, refrigerant piping, Refrigerant and Oil (First Charge), Anti-vibration isolators mountings as per mfgs recommendations, flexible pipe connector at condenser & chiller inlet / outlet, integral lubrication system, Microprocessor based control panel, chiller / floor mounted aircooled VSD with IP 54 enclosure, active harmonic filters (THDI less than 5%) & accessories etc. all mounted on M.S. frame. Motor shall be suitable for 415 volts ± 10%, 50Hz ± 5 %, three phase A.C. supply. The chilling m/c as described above shall be in line with specifications & shall have interface card compatible with BMS system. Condenser CDW IN - 29.44º C. CDW OUT - 35.0º C. FLOW - 5103 LPM Fouling Factor (MKS) - 0.0002 Pressure Drop Max - 6.5 Meter Chiller CHW IN - 12.22º C. CHW OUT - 6.67º C. FLOW - 2721 LPM Fouling Factor (MKS) - 0.0001 Pressure Drop Max - 6.5 Meter COP At AHRI Condition - 6.3 (Min) Capacity of Chiller at above operating condition - 450 TR Power Consumption Of Chiller / TR At Tender Condition Mentioned Above (Max) - 0.68 The price quoted for supply, installation, testing & commissioning of Centrifugal Water Chilling Unit shall be inclusive of all duties & taxes, insurance, transportation / shipment cost from works to site, loading / unloading, port clearance charges etc. as required in Indian Rupees. (2W+Standby Considered in Ph 1)

Condenser Water Pumps Set Supply, installation, testing and commissioning of Vertical Inline condenser water centrifugal pump sets with bronze impeller for condenser water recirculation complete with TEFC (IE3) Sq. Cage induction motor with class "F" insulation, base plate, coupling guard, SS Shaft Grade 316, bronze impeller, factory fitted mechanical seal, flexible pipe connector at inlet and outlet etc. conforming to technical specification & as per following parameters. Condenser Water Pumps Set (2W+Standby Considered in Ph 1) Capacity of Each Pump LPM 5103 Pump Head (Mt) 27.5 Motor HP (Indicative Only) 50.0 Pump Efficiency (Min) 80%

Primary Chilled Water Pumps Set Supply, installation, testing and commissioning of Vertical Inline chilled water centrifugal pump sets with bronze impeller for chilled water recirculation complete with TEFC (IE3) Sq. Cage induction motor with class "F" insulation, base plate, coupling guard, SS Shaft Grade 316, bronze impeller, factory fitted mechanical seal, flexible pipe connector at inlet and outlet etc. conforming to technical specification & as per following parameters. The chilled water pumps shall also include the cost of thermal insulation. Primary Chilled Water Pumps Set (2W+Standby Considered in Ph 1) Capacity of Each Pump LPM 4082 Pump Head (Mt) 13.00 Motor HP (Indicative Only) 20.0 Pump Efficiency (Min) 75%

Secondary Chilled Water Pumps Set Supply, installation, testing and commissioning of Vertical Inline chilled water centrifugal pump sets with bronze impeller for chilled water recirculation complete with TEFC (IE3) Sq. Cage induction motor with class "F" insulation, base plate, couplingguard, SS Shaft Grade 316, bronze impeller, factory fitted mechanical seal, flexible pipe connector at inlet and outlet etc. conforming to technical specification & as per following parameters. The chilled water pumps shall also include the cost of thermal insulation. Secondary chilled water pumps shall be suitable for operation on variable frequency drives & conforming to the specifications of variable speed pumping system. For New Building (2W+1S) Capacity of Each Pump LPM 4082 Pump Head (Mt) 22 Pump Motor HP (Indicative Only) 30 Pump Efficiency (Min) 80%

Variable Speed Pumping System for Secondary Chilled Water Pumps Supply, installation, testing and commissioning of Variable Speed Pumping system consisting of three numbers 30 HP variable frequency drive (VFD) having IP-54/55 enclosure with heat sink suitably interfaced with other system components, hand / auto macro designed for pumping application, interfacing amongst all components and compatibility of I/O signals etc complete with other accessories as required.

CTI Certified FRP Induced Draft Cooling Tower (450 TR) Supply, installation, testing and commissioning of CTI Certified FRP Induced draft, cross / counter flow, twin fan, direct driven, site erected cooling tower of capacity as mentioned below based on the parameters given below and complete with PVC Fill, Louvers, Drift Eliminator, Weather Proof IP 55 TEFC Motor (IE3), Propeller Fan, FRP Basin with additional sump in the bottom of the basin on every outlet point to avoid vortex formation in the condenser water pipe line, Hot dip galvanised Steel Ladder, Stainless Steel hardware including nut, bolt, washer etc. The cooling tower shall conform to technical specifications given in the tender. The maximum allowable sound power at a distance of 1 M from the cooling Tower shall be less than 75 dB. Tower fan motor shall be suitable for VFD operation and operation of VFD system shall be based approach of cooling tower. Water Flow - (3 GPM / TR) Designed Wet Bulb Temperature - 27.8 °C Water Inlet / Outlet Temperature - 35.0 °C / 29.44 °C Cooling Tower Basin Height - 300.0 MM Fan Motor HP (Indicative) - 2 x 15 / 20 HP Fan Motor RPM (Indicative) - Below 720 RPM Cooling Tower Capacity: (2W+Standby Considered in Ph 1)

VFD System For Cooling Tower (New Building) Supply, installation, testing and commissioning of VFD having IP-54/55 enclosure from factory with heat sink for each cooling tower fan (15 / 20 HP Each, 4 Nos.) with VFD control panel & other accessories as required. VFD control panel shall be installed in the AC Plant Room. The system shall be complete with variable frequency drive (VFD) suitably interfaced with other system components, hand / auto macro designed, 01 no. dedicated microprocessor based logic controller, software duly downloaded, tempearture Sensor / Transmitters, interfacing amongst all components and compatibility of I/O signals etc complete with other accessories as required. Operation of VFD system shall be based approach of cooling tower.

Hot Water Generator For Winter Heating / Monsoon Reheat Supply, installation, testing and commissioning of electrically operated Hot Water Generator of capacity 300 KW in multiple bank complete with PLC based microprocessor controls, electrical panels etc. confirming to technical specifications section. (1W+Standby Considered in Ph 1) Inlet Water Temperature 50 °C Outlet Water Temperature 55 °C

Hot Water Pump Sets Supply, installation, testing and commissioning of Vertical Inline hot water centrifugal pump sets with bronze impeller for hot water recirculation complete with TEFC (IE3) Sq. Cage induction motor with class "F" insulation, base plate, coupling guard, SS Shaft Grade 316, bronze impeller, factory fitted mechanical seal, flexible pipe connector at inlet and outlet etc. conforming to technical specification & as per following parameters. The hot water pumps shall also include the cost of thermal insulation. Hot water pumps shall be suitable for operation on variable frequency drives & conforming to the specifications of variable speed pumping system. Hot Water Pump Sets (1W+Standby Considered in Ph 1) Capacity of Each Pump LPM 860 Pump Head (Mt) 25.0 Motor HP 7.5

Variable Speed Pumping System for Hot Water Pumps (New Building) Supply, installation, testing and commissioning of Variable Speed Pumping system consisting of one number 7.5 HP variable frequency drive (VFD) having IP-55 enclosure with heat sink suitably interfaced with other system components, hand / auto macro designed for pumping application, interfacing amongst all components and compatibility of I/O signals etc complete with other accessories as required.

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 2,500 CFM, 40 mm St. Pr., 6 Row CC, 2 Row HC (Floor Mounted / Ceiling Suspended)

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 3,000 CFM, 45 mm St. Pr., 6 Row CC, 2 Row HC (Floor Mounted / Ceiling Suspended)

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 3,500 CFM, 45 mm St. Pr., 6 Row CC, 2 Row HC (Floor Mounted / Ceiling Suspended)

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 5,000 CFM, 45 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 6,000 CFM, 50 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 7,000 CFM, 50 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 8,000 CFM, 50 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 10,000 CFM, 50 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 Filter) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted / ceiling suspended as per HVAC Drawing, horizontal type , fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil & 2 Row Heating Coi made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 12,000 CFM, 55 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 2,500 CFM, 60 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 5,000 CFM, 65 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 6,000 CFM, 65 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 7,000 CFM, 70 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 8,000 CFM, 70 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 9,000 CFM, 70 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 10,000 CFM, 70 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 11,000 CFM, 70 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 12,000 CFM, 75 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 13,000 CFM, 75 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (CC + HC + MERV 8 & 13) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted horizontal type, fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm plain Galvanised steel sheet inside complete with blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 4 / 6 Row cooling coil and 2 row heating coil made of Aluminium finned Copper tube with coil section, Copper Header, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame, fine filter section with MERV 13 filters in extruded aluminium frame, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 25 mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete AHU shall conform to standard specication. The face velocity across coil shall be limited to 152 MPM maxm. The capacity of Air-handlers shall be as follows. The static pressure given below is for guidance only actual to be calculated by vendor. 14,000 CFM, 75 mm St. Pr., 6 Row CC, 2 Row HC

Double Skin Floor Mounted AHU (For OT With 12 ACH/Hr) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit floor mounted fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm polished SS sheet inside complete with supply & exhaust blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters for both supply & exhaust fan motor, power control panel with necessary switchgears incoming & outgoing for VFD & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 8 row cooling & 2 row heating coil made of Aluminium finned Copper tube, Copper header with coil section, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame in both the supply & exhaust side of AHU, fine filter section with MERV 13 filters in extruded aluminium frame in supply after fan, (Hepa filters shall be at terminals along with laminar flow plenum & not to be included in the cost), mixing chamber, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 48mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. These AHUs shall have air inlet / outlet connection made of aluminium 20 G & all fixing arrangement / blank off shall be of SS The complete AHU shall conform to standard specication. The face velocity across cooling / heating coil shall be limited to 152 MPM maxm. The static pressure given below is for guidance only actual to be calculated by vendor. 3500 CFM Supply Air, 8 Row CC, 2 Row HC, 125 mm St. Pr., Supply Fan, 850 CFM Ex. Air Fan, 40 mm St. Pr.for Exhaust fan with other accessories as specified)

Double Skin Floor Mounted AHU (For 100% Fresh Air OT) Supply, installation, testing and commissioning of factory fabricated Double Skinned Chilled Water Air- handling unit fabricated out of extruded aluminium section with 0.8mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.8 mm polished SS sheet inside complete with supply & exhaust blower section with single / multiple AMCA certified backward curved plug fan with aerofoil design blades, VFD with built in harmonic filters for both supply & exhaust fan motor, power control panel with necessary switchgears incoming & outgoing for VFD, HRW & humidifier, blower suitable for static pressure as required (Fan Static given below is for guideline), blower motor TEFC (IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, 8 row cooling & 2 row heating coil made of Aluminium finned Copper tube, Copper header with coil section, pre-filter section with non woven synthetic media MERV 8 filters in extruded aluminium frame in both the supply & exhaust side of AHU, fine filter section with MERV 13 filters in extruded aluminium frame in supply after fan, (Hepa filters shall be at terminals along with laminar flow plenum & not to be included in the cost), Heat Recovery Wheel with HRW Section, mixing chamber, polished stainless steel drain pan made out of 22 G sheet duly insulated etc. without face and bypass dampers. The AHU panels shall be insulated with 48mm thick & 36 Kg/m³ density PU foam & shall have thermal break. The motor & blower assembly shall be mounted on Aluminium extruded section only. These AHUs shall have air inlet / outlet connection made of aluminium 20 G & all fixing arrangement / blank off shall be of SS The complete AHU shall conform to standard specication. The face velocity across cooling / heating coil shall be limited to 152 MPM maxm. The static pressure given below is for guidance only actual shall be as per shop drawings. The capacity of Air-handlers shall be as follows: (3500 CFM Supply Air Blower, 8 Row CC, 2 Row HC, 140 mm St. Pr., 3000 CFM Ex. Air Blower, 60 mm St. Pr. with other accessories as specified above)

FCU Valves With Three Way Bypass Flushing Unit Set For Cooling Coil Supply, installation, testing and commissioning of factory insulated jacket copper / brass connection set for chilled water line consisting of Pressure Independant Balancing Cum Two Way Control Valve in a single body equipped with electronic modulating actuator working on 2-10 V DC, 4- 20 mA electric signal, ball valve with strainer at inlet, ball valve at outlet, three way bypass flushing unit, copper / brass connection set with braided pipe flexible connector at in and out at one end etc. Ball valves & strainer sizes in cooling coil shall be 25 mm up to 2 TR & 32 mm for 2.5 TR & above. PIBCV valves sizes in cooling coil shall be 20 mm up to 2 TR & 25 mm for 2.5 TR & above.

FCU Valves With Three Way Bypass Flushing Unit Set For Heating Coil Supply, installation, testing and commissioning of factory insulated jacket copper / brass connection set for hot water line consisting of Pressure Independant Balancing Cum Two Way Control Valve in a single body equipped with electronic modulating actuator working on 2-10 V DC, 4- 20 mA electric signal, ball valve with strainer at inlet, ball valve at outlet, copper / brass connection set with braided pipe flexible connector at in and out at one end etc. Ball valves & strainer sizes in heating coil shall be 20 mm up to 2 TR & 25 mm for 2.5 TR & above. PIBCV valves sizes in heating coil shall be 15 mm up to 2 TR & 20 mm for 2.5 TR & above.

Thermostat for FCU Supply, installation, testing and commissioning of automatic control for Fan Coil Units for cooling / heating consisting of pressure independant balancing cum two way control valve (already quantified herein) & digital thermostat, which will have provision of setting of room temperature, setting of fan speed (High, Medium, Low). The quoted price of thermostat shall include the cost of 20mm MS conduits, control cabling, MS Box etc as required. Thermostats shall be interlocked to prevent simultaneous heating and cooling.

Digital Display Type Thermostat For AHU Supply, installation, testing and commissioning of Proportional cooling / heating, digital display, communicating type thermostat at air-handler. Temperature Sensor for AHUs are also specified in BMS Part. Thermostat shall be installed in case BMS commissioning is significantly delayed.

For All OT AHU (T + RH Control) Supply, installation, testing and commissioning of digital display, communicating type thermostat with humidistat for various air handling Units. The thermostat with built in / individual humidistat shall have provision of setting of space temperature & RH and shall display the both. The quoted price of thermostat / humidistat shall include the cost of 20mm MS conduits, control cabling, MS Box etc as required. Temperature + RH Sensor for AHUs are also specified in BMS Part. Thermostat with built in humidistat shall be installed in case BMS commissioning is significantly delayed.

Pressure Independant Balancing Cum Two Way Control Valve (Cooling Coil For AHU) Supply, installation, testing and commissioning of Pressure Independant Balancing Cum Two Way Control Valve in a single body equipped with electronic modulating actuator working on 2-10 V DC, 4- 20 mA electric signal. The minimum close off Pressure of actuator must be 1.5 times shut off head of pump as per specifications of following sizes: 32 mm Dia, Maximum 15 GPM

Pressure Independant Balancing Cum Two Way Control Valve (Cooling Coil For AHU) Supply, installation, testing and commissioning of Pressure Independant Balancing Cum Two Way Control Valve in a single body equipped with electronic modulating actuator working on 2-10 V DC, 4- 20 mA electric signal. The minimum close off Pressure of actuator must be 1.5 times shut off head of pump as per specifications of following sizes: 40 mm Dia, Maximum 26 GPM

Pressure Independant Balancing Cum Two Way Control Valve (Cooling Coil For AHU) Supply, installation, testing and commissioning of Pressure Independant Balancing Cum Two Way Control Valve in a single body equipped with electronic modulating actuator working on 2-10 V DC, 4- 20 mA electric signal. The minimum close off Pressure of actuator must be 1.5 times shut off head of pump as per specifications of following sizes: 50 mm Dia, Maximum 54 GPM

Pressure Independant Balancing Cum Two Way Control Valve (Cooling Coil For AHU) Supply, installation, testing and commissioning of Pressure Independant Balancing Cum Two Way Control Valve in a single body equipped with electronic modulating actuator working on 2-10 V DC, 4- 20 mA electric signal. The minimum close off Pressure of actuator must be 1.5 times shut off head of pump as per specifications of following sizes: 65 mm Dia, Maximum 80 GPM

Pressure Independant Balancing Cum Two Way Control Valve (Cooling Coil For AHU) Supply, installation, testing and commissioning of Pressure Independant Balancing Cum Two Way Control Valve in a single body equipped with electronic modulating actuator working on 2-10 V DC, 4- 20 mA electric signal. The minimum close off Pressure of actuator must be 1.5 times shut off head of pump as per specifications of following sizes: 80 mm Dia, Maximum 125 GPM

Plastic Propeller Fans Supply, installation, testing and commissioning of propeller exhaust fans of various capacities as given below suitable for 240 volts, 50 Hz, single phase AC supply complete with gravity louvers & speed regulator etc. 100 CFM

Plastic Propeller Fans Supply, installation, testing and commissioning of propeller exhaust fans of various capacities as given below suitable for 240 volts, 50 Hz, single phase AC supply complete with gravity louvers & speed regulator etc. 200 CFM

Plastic Propeller Fans Supply, installation, testing and commissioning of propeller exhaust fans of various capacities as given below suitable for 240 volts, 50 Hz, single phase AC supply complete with gravity louvers & speed regulator etc. 400 CFM

Plastic Propeller Fans Supply, installation, testing and commissioning of propeller exhaust fans of various capacities as given below suitable for 240 volts, 50 Hz, single phase AC supply complete with gravity louvers & speed regulator etc. 500 CFM

Plastic Propeller Fans Supply, installation, testing and commissioning of propeller exhaust fans of various capacities as given below suitable for 240 volts, 50 Hz, single phase AC supply complete with gravity louvers & speed regulator etc. 700 CFM

Factory Fabricated Double Skin Airwasher Supply, installation, testing and commissioning of factory fabricated Double Skinned Air-washer unit floor mounted type fabricated out of extruded aluminium section with 0.6mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.6 mm plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC (Motor Efficiency IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, belt drive package, wet section & tank shall be made of 18 G stainless steel. The Air-washer shall be complete with fill of depth 200 mm & face velocity across the fill shall be limited to 152 MPM. The Air-washer shall have an efficiency of 90% & shall be complete with water circulation pump GI B Class interconnecting piping & valves Aluminum viscous filters. The Air-washer shall have an efficiency of 90% & shall be complete with water circulation pump GI B Class interconnecting piping & valves Aluminum viscous filters. The airwasher panels shall be insulated with 23mm thick & 36 Kg/m³ density PU foam. The Airwasher shall conform to specication given in the tender & shall be of following capacity. 25,000 CFM, 1 x 800 mm Dia. Fan, 1 x 15 Kw Fan Motor, 50 mm St. Pressure, Monoblock Pump

Mechanical Ventilation Unit (MVU) Supply, installation, testing and commissioning of factory fabricated Double Skinned Mechanical Ventilation Unit floor mounted type fabricated out of extruded aluminium section with 0.6mm pre-plasticized / pre-coated Galvanised steel sheet outside & 0.6 mm plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC (Efficiency Class 1) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, pre-filter section with non woven synthetic media of 10 micron particle size with an efficiency of 90%, polished stainless steel drain pan made out of 22 G sheet duly insulated complete with belt drive package etc. The AHU panels shall be insulated with 23mm thick & 36 Kg/m³ density PU foam. The motor & blower assembly shall be mounted on Aluminium extruded section only. The complete MVU shall conform to tender specication. The capacity of MVU shall be as follows: 20,000 CFM, 25mm st. pr, 800 mm Dia Fan, 10.0 HP, 1440 RPM Fan Motor, Belt Driven

Factory Fabricated Double Skin Scrubber Supply, installation, testing and commissioning of factory fabricated Double Skinned Scrubber unit floor mounted type fabricated out of extruded aluminium section with 0.6mm pre-plasticized /pre-coated Galvanised steel sheet outside & 0.6 mm plain Galvanised steel sheet inside with blower, blower section and blower motor TEFC (Motor Efficiency IE3) type suitable for operation on 415 volts ± 10%, 50 Hz ± 5% AC supply, belt drive package, wet section & tank shall be made of 18 G tainless steel. The Scrubber shall be complete with spray arrangement with metallic viscous filter & face velocity across the section shall be limited to 152 MPM. The scrubber shall have an efficiency of 90% & shall be complete with water circulation pump GI B Class interconnecting piping & valves, viscous filters. The scrubber panels shall be insulated with 23mm thick & 36 Kg/m³ density PU foam. The scrubber shall conform to specication given in the tender & shall be of following capacity. 26,000 CFM, 1 x 800 mm Dia. Fan, 1 x 18.5 Kw Fan Motor, 80 mm St. Pressure, Monoblock Pump For Kitchen

VFD For 50% of Basment Parking Ventilation Fan (Only Normal Mode) Supply, installation, testing and commissioning of BMS compitable VFD for Axial Fan Motor having IP-54 OEM enclosure with heat sink, Built-in Harmonic Filters (ThDi less than 5%), EMC Filters (Electromagnetic Compatibility Filters Category C2 as per EN 61800-3), 2 PID Controlers, Automatic Energy Optimization / Load dependent flux optimization functionality for maximum energy savings & complying with the tender specifications. 7.5 / 9.3 / 11 KW Motor

CO Based Sensing System For Automated Working Of Parking Ventilation Fans (Normal & Fire Mode) Supply, installation, testing and commissioning of CO based sensing system for automatic running & modulating the VFD motor for parking ventilation supply and exahust fans for normal mode operation. Each set of system for each zone shall have four number of infrared CO senser, Sensor shall have following measuring range & accuracy:- CO ( Electrochemical Type ) - Minimum measuring range : 0 ~ 500 ppm. Coverage of each sensor shall be 5500 Sq Ft & six number shall be placed in each zone The fan control mechanism shall be based on variable frequency drive . Each zone shall have controlled ventilation rate of 25% of the specified fan capacity at a given frequency, when CO measurement is below 25 ppm & Ventilation rate shall increase proportionally when CO level increase beyond 25 ppm and reach the maximum fan capacity when CO level is above 50 ppm. IF CO level reaches 150 ppm then fans in fire mode shall be switched on automatically. User should be able to vary these setpoints through web based software interface / supervisory controller. Logic Controller shall also have the logic to switch ON the fan when CO is above 20 ppm & switched OFF again when CO drops below 15 ppm. Logic Controller shall also have the facility of Timer & Manual Override for fan operation.

Standalone, Networkable, Intelligent Microprocessor based Programmable DDC Supply, installation, testing and commissioning of one no. Standalone Intelligent Microprocessor based Programmable DDC (For Each Zone) with inbuilt HMI , Onboard Modbus port & network functionalities based upon KNX protocol along with suitable Enclosures with all accessories including necessary switchgear, step down transformer, internal power and control cabling (excluding power & control cable to Fan), complete in all respect & as required to suit the site conditions etc. Each Set of DDC Controller should have 1 AI, 8 DI, 2 AO, 4 DO as per IO Summary given in specification per Zone. (UPS Power Supply By Client to each DDC)

Ultrasonic Humidifier For OT AHUs Supply, installation, testing and commissioning of horizontal floor standing Ultrasonic Humidifier with casters made out of 1.2 mm thick SS-304 sheet complete with Piezo transducers duly interlocked with Level switches. Control Panel made out of 1.2 mm thick CRCA sheet comprising of Incomer MCB, Contactor, On/Off switch, step down transformer, ventilation fan, Power and control wiring. The Ultrasonic humidifier shall be equipped with solenoid operated water makeup, Drain valve, Water Overflow connection with valve, Mist outlet connection, Water and Air filter assembly, Level switches for upper and lower water level and other controls as per tender specifications. All basic controls and terminals shall be located in an integral control cabinet factory wired and tested. Humidifier shall comply the tender specification & of following capacities: 10 LPH Capacity

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 300 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 250 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 200 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 150 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 125 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 100 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 80 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 65 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 50 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 40 mm dia. (32 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 32 mm dia. (19 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 25 mm dia. (19 mm thick insulation)

Chilled / Hot Water Piping With Nitrile Rubber Insulation Supplying, laying/ fixing, testing and commissioning of following nominal sizes of chilled water piping inside the building (with necessary clamps, vibration isolators and fittings but excluding valves, strainers, gauges etc.) duly insulated with following closed cell elastometric nitrile rubber of minimum 45 Kg / m3 density, thermal conductivity 0.037 W/MK or better at 20 deg mean temperature class 'O' insulation applied by suitable adhesive complete including repairing of damage to building etc. as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 20 mm dia. (19 mm thick insulation)

Motorised Butterfly Valves Supply, installation, testing and commissioning of motorised on / off butterfly valves with modulating motor in return chilled & hot water line of each chiller & Hot Water Generator operated through BMS & of following sizes. Valves shall be insulated as per pipe insulation material & thickness given above. 200 mm dia (For Chiller)

Motorised Butterfly Valves Supply, installation, testing and commissioning of motorised on / off butterfly valves with modulating motor in return chilled & hot water line of each chiller & Hot Water Generator operated through BMS & of following sizes. Valves shall be insulated as per pipe insulation material & thickness given above. 100 mm dia (For Hot Water Generator)

Manual Balancing Valves BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. 200 mm dia (For Chiller)

Manual Balancing Valves BALANCING VALVE WITH BUILT IN MEASURING FACILITY with C I body flanged construction with EPDM coated disc with long pitch with protected out pipe insulation & PN 16 pressure rating for chilled / hot water circulation as specified. 100 mm dia (For Hot Water Generator)

Supply, installation, testing and commissioning of following valves in chilled / hot water line as per specification given in the tender. Valves shall be insulated as per pipe insulation material & thickness given above. 19 mm dia

Supply, installation, testing and commissioning of following valves in chilled / hot water line as per specification given in the tender. Valves shall be insulated as per pipe insulation material & thickness given above. 25 mm dia

Supply, installation, testing and commissioning of following valves in chilled / hot water line as per specification given in the tender. Valves shall be insulated as per pipe insulation material & thickness given above. 32 mm dia

Supply, installation, testing and commissioning of following valves in chilled / hot water line as per specification given in the tender. Valves shall be insulated as per pipe insulation material & thickness given above. 40 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 200 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 150 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 125 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 100 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 80 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 65 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/ hot eater circulation as specified 50 mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. 200 mm dia

NON - RETURN VALVE with duel plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating for chilled / hot water circulation including insulation as specified. 100 mm dia

Y-strainer ( With Insulation ) - 200 mm dia

Y-strainer ( With Insulation ) - 100 mm dia

Y-strainer ( With Insulation ) - 80 mm dia

Y-strainer ( With Insulation ) - 65 mm dia

Y-strainer ( With Insulation ) - 50 mm dia

Y-strainer ( With Insulation ) - 40 mm dia

Y-strainer ( With Insulation ) - 32 mm dia

Y-strainer ( With Insulation ) - 25 mm dia

Pressure Gauges Supply, installation, testing and commissioning of pressure guage of approved make of dia 150 mm conforming to tender specifications.

Thermometer Providing & fixing in position the mercury in glass industrial type thermometers.

Condensate Drain Piping With Nitrile Rubber Insulation Supply, installation, testing and commissioning of condensate drain water piping of GI 'Medium' class complete with fittings like elbows, tees, reducers, bends, MS flanges, supports, welding, painting etc. as required conforming to tender specifications and of following sizes. Complete pipe shall be duly insulated with Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness in the tender specification & suitable for indoor / outdoor application. Complete pipe insulation shall also have 200 g/m² factory laminated, treated woven Glass Cloth coating for mechanical and UV protection. 25 mm dia pipe, 13 mm Insulation

Condensate Drain Piping With Nitrile Rubber Insulation Supply, installation, testing and commissioning of condensate drain water piping of GI 'Medium' class complete with fittings like elbows, tees, reducers, bends, MS flanges, supports, welding, painting etc. as required conforming to tender specifications and of following sizes. Complete pipe shall be duly insulated with Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness in the tender specification & suitable for indoor / outdoor application. Complete pipe insulation shall also have 200 g/m² factory laminated, treated woven Glass Cloth coating for mechanical and UV protection. 32 mm dia pipe, 13 mm Insulation

Condensate Drain Piping With Nitrile Rubber Insulation Supply, installation, testing and commissioning of condensate drain water piping of GI 'Medium' class complete with fittings like elbows, tees, reducers, bends, MS flanges, supports, welding, painting etc. as required conforming to tender specifications and of following sizes. Complete pipe shall be duly insulated with Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness in the tender specification & suitable for indoor / outdoor application. Complete pipe insulation shall also have 200 g/m² factory laminated, treated woven Glass Cloth coating for mechanical and UV protection. 40 mm dia pipe, 13 mm Insulation

Condensate Drain Piping With Nitrile Rubber Insulation Supply, installation, testing and commissioning of condensate drain water piping of GI 'Medium' class complete with fittings like elbows, tees, reducers, bends, MS flanges, supports, welding, painting etc. as required conforming to tender specifications and of following sizes. Complete pipe shall be duly insulated with Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness in the tender specification & suitable for indoor / outdoor application. Complete pipe insulation shall also have 200 g/m² factory laminated, treated woven Glass Cloth coating for mechanical and UV protection. 50 mm dia pipe , 19 mm Insulation

Condensate Drain Piping With Nitrile Rubber Insulation Supply, installation, testing and commissioning of condensate drain water piping of GI 'Medium' class complete with fittings like elbows, tees, reducers, bends, MS flanges, supports, welding, painting etc. as required conforming to tender specifications and of following sizes. Complete pipe shall be duly insulated with Closed Cell Elastomeric Nitrile Rubber of specified pipe section of specified thickness in the tender specification & suitable for indoor / outdoor application. Complete pipe insulation shall also have 200 g/m² factory laminated, treated woven Glass Cloth coating for mechanical and UV protection. 65 mm dia pipe, 19 mm Insulation

Auto Air Vent Supply, installation, testing and commissioning of auto air vent valve of following sizes and complying with tender specification. a) 10 mm dia auto air vent valve

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 300 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 250 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 200 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 150 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 125 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 100 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 80 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 65 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 50 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 40 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 32 mm dia. (19 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 25 mm dia. (19 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect.20 mm dia. (19 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 200 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 125 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 100 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 80 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 65 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 50 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 40 mm dia. (32 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 32 mm dia. (19 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 25 mm dia. (19 mm thick insulation)

Supplying & finishing of insulated CHW / HW pipes & valves with 24 G Aluminium sheet cladding with hand operated roller machine (Grooving Machine) & finally to be fixed with self tapping screws as per specifications & complete in all respect. 20 mm dia. (19 mm thick insulation)

Burried Chilled / Hot Water Piping With TF Quality Expanded Polysterene Insulation & Sand Cement Plaster Supplying, laying / fixing, testing and commissioning of following nominal sizes of chilled / hot water piping outside the building laid in the ground including earth excavation & filling as required (with necessary clamps and fittings but excluding valves, strainers, gauges etc.) duly insulated with following thickness TF Quality Expanded Polysterene of minimum 20 Kg / m3 density, thermal conductivity 0.035 (K.cal/ hr. degree C/m or better at 10 deg mean temperature covered with 500 gauge polythene faced hessian with 50 mm overlap, All joints sealed with bitumen, A layer of 0.50 mm x 20 mm G.I. wire mesh netting provided over it butting all joints and laced down with GI wire, sand cement plaster (1:4) 20 mm. thick provided in 2 layers of each 10mm and water proofed by applying hot bitumen & fixing tar felt over the plaster as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 300 mm dia. (75 mm thick insulation)

Burried Chilled / Hot Water Piping With TF Quality Expanded Polysterene Insulation & Sand Cement Plaster Supplying, laying / fixing, testing and commissioning of following nominal sizes of chilled / hot water piping outside the building laid in the ground including earth excavation & filling as required (with necessary clamps and fittings but excluding valves, strainers, gauges etc.) duly insulated with following thickness TF Quality Expanded Polysterene of minimum 20 Kg / m3 density, thermal conductivity 0.035 (K.cal/ hr. degree C/m or better at 10 deg mean temperature covered with 500 gauge polythene faced hessian with 50 mm overlap, All joints sealed with bitumen, A layer of 0.50 mm x 20 mm G.I. wire mesh netting provided over it butting all joints and laced down with GI wire, sand cement plaster (1:4) 20 mm. thick provided in 2 layers of each 10mm and water proofed by applying hot bitumen & fixing tar felt over the plaster as per specifications and as required complete in all respect. Note:-The Pipes of sizes 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 125 mm dia. (50 mm thick insulation)

Condenser Water Piping Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends, tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 50 mm dia pipe

Condenser Water Piping Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends, tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 150 mm dia pipe

Condenser Water Piping Supplying, fixing, testing and commissioning of condenser water pipes of following sizes of MS 'C' class along with necessary clamps, vibration isolators and fittings such as bends, tees etc..but excluding valves, strainers, gauges etc. adequately supported on rigid supports duly painted/buried in ground excavation and refilling etc. as per specification and as required complete in all respect. Note:-The Pipes size 150 mm & below shall be M.S. 'C' class as per IS : 1239 and pipes size above 150 mm shall be welded black steel pipe heavy class as per IS: 3589, from minimum 6.35 mm thick M.S. Sheet for pipes upto 350 mm dia. and from minimum 7mm thick MS sheet for pipes of 400 mm dia and above. 250 mm dia pipe

Motorised Butterfly Valves Supplying, fixing, testing and commissioning of following sizes Motorized Butterfly Valve with CI Body, SS Disc, O - ring and minimum PN-16 pressure rating, conforming to BS 5155, IS 13095, with IP-55 actuator, capable of accepting upto 10V DC , and upto 20 mA electric signal and providing similar transduced feedback output to control system as required. 250 mm dia (For Condenser Out, Cooling Tower In & Out)

Supply, installation, testing and commissioning of manual balancing valves in return chilled and condenser water line of each chiller, condenser and cooling tower as per tender specification & of following sizes: 250 mm dia (For Condenser Out, Cooling Tower In)

Supply, installation, testing and commissioning of BUTTERFLY VALVE (MANUAL) with CI body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 50 mm dia

Supply, installation, testing and commissioning of BUTTERFLY VALVE (MANUAL) with CI body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 250 mm dia

Supply, installation, testing and commissioning of BUTTERFLY VALVE (MANUAL) with CI body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 450 mm dia

NON - RETURN VALVE with dual plate of CI body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as specified. 250 mm dia

Supply, installation, testing and commissioning of PN 16 rating Pot - Strainer of the following sizes confirming to tender specification. a) 450 mm dia

Rectangular GI Ducting (Factory Made - L Shape) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 24 G (Up To 750 mm)

Rectangular GI Ducting (Factory Made - L Shape) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 22 G (751 to 1500 mm)

Rectangular GI Ducting (Factory Made - L Shape) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 20 G (1501 to 2250 mm)

Rectangular GI Ducting (Factory Made - L Shape) Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. 18 G (Above 2250 mm)

Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required a) 24 G (Up To 750 mm)

Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required b) 22 G (751 to 1500 mm)

Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required c) 20 G (1501 to 2250 mm)

Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required d) 18 G (Above 2250 mm)

Supply, fabrication, installation & testing of Aluminium sheet metal ducting duly polysulphide sealed complete with Spliter Damper, vanes etc. as required for OT and as per ISI specifications and as per approved shop drawings. 22 G

Supply, fabrication, installation & testing of Aluminium sheet metal ducting duly polysulphide sealed complete with Spliter Damper, vanes etc. as required for OT and as per ISI specifications and as per approved shop drawings. 20 G

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Supplying and fixing of external thermal insulation on ducts with EPDM Rubber foam with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000, tape & adhesive (pidilite SR -998) as required of following thickness. 9 mm

Supplying and fixing of external thermal insulation on ducts with EPDM Rubber foam with completely closed cell structure as per specifications - Density 40-60 kg /cum , Class A as per ASTM E 84 , Class V-0 as per UL 94 and Mu value > 7000, tape & adhesive (pidilite SR -998) as required of following thickness. 13 mm

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Fire Damper

Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring,the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. The damper shall also be closed in the event of fire signal complete as required and as per specifications. Actuator

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminium without volume control dampers with anti smudge ring & removable core.

Fresh / Exhaust air louvers with bird screen & damper

Volume control GI Dampers to be provided in supply & Exhaust air registers / terminals.

Supply, installtion and testing of Powder coated Aluminium extruded Fixed bar linear air register of - 100 mm

Supply, installtion and testing of Powder coated Aluminium extruded Fixed bar linear air register of - 150 mm

Supply, installtion and testing of Powder coated Aluminium extruded Fixed bar linear air register of - 200 mm

Supply, installtion and testing of Powder coated Aluminium extruded Slot linear air diffusers of - 2 Slot

Supply, installtion and testing of Powder coated Aluminium extruded Slot linear air diffusers of - 3 Slot

GSS Duct Damper Supply, installation and testing of multiblade box type Galvanized Sheet Steel construction damper for ducts to be provided with suitable links and quadrants for control of volume of air.

Supply, Installation, testing & Commissioning of single phase MCB of following capacity: 16 A SP MCB, SET-01

Supply, Installation, testing & Commissioning of 63 A 6 pole isolator switch with sheet metal enclosure, rain protection etc. as required to suit the site condition.

Supply, Installation, testing & Commissioning of 40 / 63 A 3 pole isolator switch with sheet metal enclosure, rain protection etc. as required to suit the site condition.

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Chiller (315 Kw Each) 2 x 3.5C x 300 Sq. mm (Rate For Single Run)

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For CHW Pump, Cooling Tower Fan (20 HP Each) 2 x 3C x 16 Sq. mm (Rate For Single Run)

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For CDW Pump (50 HP Each) 2 x 3C x 35 Sq. mm (Rate For Single Run)

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For HW Pump (7.5 HP Each) 1 x 3C x 6 Sq. mm (Rate For Single Run)

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Hot Water Generator (300 Kw Each) 2 x 4C x 240 Sq. mm (Rate For Single Run)

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Motor Up to 3.73 Kw 1 x 3C x 4 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Motor of 5.5 Kw 1 x 3C x 6 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Motor of 7.5 to 11 Kw 2 x 3C x 6 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Motor of 15.0 Kw 2 x 3C x 16 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Motor of 18.65 Kw 2 x 3C x 16 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Motor of 22.5 Kw 2 x 3C x 25 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. For Inline Fan / FCU 1 x 3C x 2.5 Sq. mm Copper

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. Control cabling (PVC insulated Copper conductor of 1.1 KV Grade armoured cable) 3C x 1.5 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. Control cabling (PVC insulated Copper conductor of 1.1 KV Grade armoured cable) 4C x 1.5 Sq. mm

Supply, laying, testing and commissioning of power and control cabling as per specification given in the tender. Power cabling of XLPE insulated Aluminium conductor armoured cables of 1.1 KV Grade including cable end termination with brass compression glands & aluminium lugs etc as per specification. Control cabling (PVC insulated Copper conductor of 1.1 KV Grade armoured cable) 5C x 1.5 Sq. mm

Supply & laying of 32 x 6 mm GI strip recess / surface as strip earth lead including soldering etc. as required.

Supply & laying of 25 x 6 mm GI strip recess / surface as strip earth lead including soldering etc. as required.

Supply & laying of 4 SWG GI wire or in recess for loop earthing as required.

Supply & laying of 6 SWG GI wire or in recess for loop earthing as required.

Supply and fixing rubber matting conforming to IS-15652-2006 complete etc. as required.

Fabricating and installing following size of perforated M.S. Cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including painting with powder coating etc as required. 100 mm wide x 50 mm x 1.6 mm

Fabricating and installing following size of perforated M.S. Cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including painting with powder coating etc as required. 150 mm wide x 50 mm x 1.6 mm

Fabricating and installing following size of perforated M.S. Cable trays including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including painting with powder coating etc as required. 300 mm wide x 50 mm x 1.6 mm

Junction Box For FCU / Propeller / Inline Fan etc (Single Phase) Supply, Installation, Testing & Commissioning of 4" x 3" x 3" G.I. Box with modular type 6A socket & switch, modular cover plate etc as required at site.

Supply, installation, testing and commissioning of Current relay for pumps (5 Nos. Primary CHW Pumps, 5 Nos. CDW Pumps, Excluding Pumps on VFD)

Supply, installation, testing and commissioning of Differential pressure switch for various vent. fans excluding Inline & Propeller Fans

Supply, installation, testing and commissioning of Differential pressure switch for AHU blower status

Supply, installation, testing and commissioning of Differential pressure switch AHU Pre, Fine & Hepa Filter status

Supply, installation, testing and commissioning of Communication & Signal Cabling 2C x 1.5 Sq. mm Shielded Tinned Copper Cable.

Supply, installation, testing and commissioning of MS Conduit 25 mm for Signal & Communication Cable

Hi-wall Split Unit (5 Star Rated) For Various Areas as per basis of design, UPS, Server, Hub Room etc. Supply, installation, testing and commissioning of Hi-wall Split Unit with rotary compressor & cordless control of following capacity with outdoor unit stand, power & control cabling, MCB etc. as required. 1.5 TR

Hi-wall Split Unit (5 Star Rated) For Various Areas as per basis of design, UPS, Server, Hub Room etc. Supply, installation, testing and commissioning of Hi-wall Split Unit with rotary compressor & cordless control of following capacity with outdoor unit stand, power & control cabling, MCB etc. as required. 2.0 TR

Supply, installation, testing and commissioning of additional refrigerant piping (two lengths) duly insulated with 25 mm for indoor application and 38 mm for outdoor application closed cell nitrile rubber of density 60+/-10% Kg/m3 to interconnect indoor & outdoor units for each circuit. (Refrigerant piping for individual circuit shall be restricted to maximum length of 25 Meter by AC Contractor) Hi-wall Split Units (1.5 / 2.0 TR)

"MEDICAL GAS PIPELINE SYSTEM Supply,Instllation testing and commissiong of Copper Piping as per technical specification BS: 13348 KITE MARK 76mmODX1.5mm thick =180 Mtrs." "Supply,Instllation testing and commissiong of Copper Piping as per technical specification BS: 13348 KITE MARK 54mmODX1.2mm thick = 350Mtrs." "Supply,Instllation testing and commissiong of Copper Piping as per technical specification BS: 13348 KITE MARK 42mm ODX1.2mm thick =250Mtrs." "Supply,Instllation testing and commissiong of Copper Piping as per technical specification BS: 13348 KITE MARK 28mmODX 1.0mm thick =2050Mtrs." "Supply,Instllation testing and commissiong of Copper Piping as per technical specification BS: 13348 KITE MARK 22mmODX 1.0mm thick = 5850Mtrs." "Supply,Instllation testing and commissiong of Copper Piping as per technical specification BS: 13348 KITE MARK 15mm ODX 1.0mm thick = 4950Mtrs." "Supply,Instllation testing and commissiong of Copper Piping as per technical specification BS: 13348 KITE MARK 12mm ODX 1.0mm thick 1730Mtrs." Supply,Installation, testing and commissioning of Gas outlet points for Oxygen as per technical specification NFPA-99 UL / ETL Listed (imported)for Oxygen =606No. Supply,Installation, testing and commissioning of Gas outlet points for Nitrous Oxide as per technical specification NFPA-99 UL / ETL Listed (imported) for Nitrous Oxide =26No. Supply,Installation, testing and commissioning of Gas outlet points for Oxygen, Nitrous Oxide, Air, & Vacuum system as per technical specification NFPA-99 UL / ETL Listed (imported) for Compressed Air ( 4 Bar )=143No. Supply,Installation, testing and commissioning of Gas outlet points for Oxygen, Nitrous Oxide, Air, & Vacuum system as per technical specification NFPA-99 UL / ETL Listed (imported) For Compressed Air (7 Bar) =16No. Supply,Installation, testing and commissioning of Gas outlet points for Oxygen, Nitrous Oxide, Air, & Vacuum system as per technical specification NFPA-99 UL / ETL Listed (imported) For Vacuum =580No. Supply,Installation, testing and commissioning of Gas outlet points for Oxygen, Nitrous Oxide, Air, & Vacuum system as per technical specification NFPA-99 UL / ETL Listed (imported) For AGSS/WAGD=12No. Matching Probe/adopter With one end suitable for Hose & other end suitable for terminal units as per technical specifications NFPA-99 UL / ETL Listed (imported) For Oxygen =606 No. Matching Probe/adopter With one end suitable for Hose & other end suitable for terminal units as per technical specifications NFPA-99 UL / ETL Listed (imported) For Nitrous Oxide =26 No. Matching Probe/adopter With one end suitable for Hose & other end suitable for terminal units as per technical specifications NFPA-99 UL / ETL Listed (imported) For Compressed Air ( 4 Bar )_=143 No. Matching Probe/adopter With one end suitable for Hose & other end suitable for terminal units as per technical specifications NFPA-99 UL / ETL Listed (imported) Fro Compressed Air (7 Bar) = 16 No. Matching Probe/adopter With one end suitable for Hose & other end suitable for terminal units as per technical specifications NFPA-99 UL / ETL Listed (imported) For Vacuum =580 No. Matching Probe/adopter With one end suitable for Hose & other end suitable for terminal units as per technical specifications NFPA-99 UL / ETL Listed (imported) For AGSS/WAGD =12 No. "Line Pressure Alarm Supply, Installation, testing and commissioning of Integrated / Combined alarm -valve box as per NFPA 99 (imported) as per tender specifications. Master Alarm Panel = 1 No. = " "Supply, Installation, testing and commissioning of Integrated / Combined alarm -valve box as per NFPA 99 (imported) as per tender specifications. Areas Alarms Panel: - 2 Gas Service =29 No." "Supply, Installation, testing and commissioning of Integrated / Combined alarm -valve box as per NFPA 99 (imported) as per tender specifications. Areas Alarms Panel: - 3 Gas Service =8 nos" "Supply, Installation, testing and commissioning of Integrated / Combined alarm -valve box as per NFPA 99 (imported) as per tender specifications. Areas Alarms Panel: - 5 Gas Service = 8 nos" supply, Installation testing and commissioning of Fully Automatic Oxygen Control System ( Improted for Oxygen as technical specifications. NFPA-99 (imported) =1 Set Supply, Installation, Testing and Commissioning of fully Oxygen Manifold ( 20+20 ) as per technical specifications. The cylinders shall not be included in the quoted price. = 492 No. = =1 Set Supply, Installation, testing and commissioning of 10 cylinder Emergency Oxygen Supply System as per technical specifications. The cylinders shall not be included in the quoted price. = 1 Set Supply installation, testing and commissioning of oxygen flow meter with humidifier bottle 0-15Litres, European CE Marked (imported) and as per technical specifications =492 No. supply installation testing and commission of fully automatic Gas Control Panel for Nitrous Oxide (Imported) as per technical specifications NFPA-99 (imported) = 1 No supply installation testing and commissioning of nitrous Oxide Manifold ( 4+4) as per technical specifications. The cylinder shall not be included on the quoted price.= 1 set supply installation, testing and commissioning of 4 cylinder Emergency Nitrous Oxide supply System as per technical specifications. The cylinder shall not be included in the quoted price. = 1 set supply, installation, testing and commissioning compressors Air system as per technical specifications.= 1 set Supply installation testing and commissining of Medical vacuum plant as per technical specifications = 1 no Suply installation testing and commissiong of Ward suction unit with above 600 Ml sucton collection jar as per specifications and European CE marked (imported)= 492 No Supply installation, testing and commissioning ofTheatre Suctin Unit with 2 Nos. 2000 Ml Jars as per technical specifications European CE marked (imported) = 12 No Supply installation testing and commissioning of High pressure Hose antistatic duly colour coded for oxygen , Nitrous Oxide Compressed air and vacuum as per technical specification . = 500 Mtr supply installation testing and commissioning of Horizontal Bed Head Panel CE certified as per specifications = 153 No supply, installation, testing and commissioning of compressors WAGD / AGSS sysytem per technical specifications.NFPA-99 (imported) = 1 No S/I/T/C of Medical Line Valve, as per Certified / UL Listed as per Technical specification - 15mm OD = 12 No S/I/T/C of Medical Line Valve, as per Certified / UL Listed as per Technical specification - 22mm OD = 30 No S/I/T/C of Medical Line Valve, as per Certified / UL Listed as per Technical specification - 28mm OD = 22 No S/I/T/C of Medical Line Valve, as per Certified / UL Listed as per Technical specification - 42mmOD = 4 No. S/I/T/C of Medical Line Valve, as per Certified / UL Listed as per Technical specification - 54mmOD = 4 No. S/I/T/C of Medical Line Valve, as per Certified / UL Listed as per Technical specification - 76mmOD = 2 No.

MODULAR OPERATION THEATER MOT comprising of walls & ceiling system for operating area, steel framework, static dissipative flooring, laminar flow, double dome OT light, touch screen surgeon’s control panel, scrub station, X ray viewing screen, hatch box, automatic sliding doors, anesthesia pendent, surgeon pendent etc. With stainless steel technology

CSSD EQUIPMENTS Horizontal Rectangular High Pressure High Vacuum Steam Sterilizer, Radial Hinged Double door, Inner chamber size: 600mm Width x 600mm height x 1200mm length, 400-450 litres volume, fully automatic cycle operation with printer, electrical operated, as per technical specification

Stainless steel SS 316 carriage suitable for above rectangular sterilizer, 400-450 litres volume, as per technical specification

Stainless steel SS 304 trolley suitable for above rectangular sterilizer, 400-450 litres volume, as per technical specification

Horizontal rectangular High Pressure High Vacuum Steam Sterilizer, Radial Hinged Double door, Inner chamber size: 450mm width x 450mm height x 1200mm length, 200-250 litres volume, fully automatic cycle operation with printer, electrical operated , as per technical specification

Stainless steel SS 316 carriage suitable for above rectangular sterilizer, 200-250 litres volume, as per technical specification

Stainless steel SS 304 trolley suitable for above rectangular sterilizer, 200-250 litres volume, as per technical specification

Washer disinfector with inbuilt drier,Double door, 250-275 litres capacity, as per technical specification

Ultrasonic cleaner 30 litres capacity, as per technical specification

Drying cabinet, 275 litres capacity, as per technical specification

Strainless steel work table with double sink, as per technical specification

Spray Gunriser with eight attachments, as per technical specification

Stainless steel control and packing table with drawer, as per technical specification

Strainless steel work table with undershelf, as per technical specification

Table mounted heat sealing machine, as per technical specification

Stainless steel Table Mounted Gauze cutting machine, as per technical specification

Stainless steel Pass Box, Double door, size: 600mm x 600mm, as per technical specification

Stainless steel Table Trolley with 2 shelves, as per technical specification

Stainless steel Closed Distribution Trolley, as per technical specification

Stainless steel Storage Rack with 5 shelves, as per technical specification

TSSU EQUIPMENTS Horizontal Cylindrical High speed instrument Sterilizer, single door, Inner chamber size: 400mm width x 600mm depth, 75-80 litres volume, manual cycle operation, electrically operated, 18KW and as per technical specification

Strainless steel work table with undershelf, as per technical specification

Stainless steel control and packing table with drawer, as per technical specification

Strainless steel work table with Single sink, as per technical specification

Spray Gunriser with eight attachments, as per technical specification

Washer disinfector,single door, 250-275 litres capacity, as per technical specification

Ultrasonic cleaner 30 litres capacity, as per technical specification

Drying cabinet, 275 litres capacity, as per technical specification

Hot and Cold Water Sterilizer, 10 Litres/Hour output, as per technical specification

Stainless steel Storage Rack with five shelves, as per technical specification

Supplying & fixing of retro reflective sign plates of required size. The plate made of High intensity prismatic grade type IV retro reflective sheeting of 3M / Avery Denison or equivalent make approved by I.R.C. / M.O.S.T. with message and graphics to be overlay film/High intensity prismatic grade type IV retro reflective sheeting of 3M / Avery Denison or equivalent make approved by I.R.C. / M.O.S.T Reflective tape of same make duly plotter cut, of approved color, letters (single side) in white colour, to be pasted on 3mm thick ACP sheet of make Alstone / Alstrong / Eurobond / Alucobond or equivalent etc. as per drawings. The sign boards shall fixeed on wall/ roof duly fixed with rawls plugs stainless steel srew/ double side tape 3M make/ SS chain of required size of required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of 18 gauge Stainless Steel plates with water jet cutting of grade 304 etching (engraved)signage plate of required size and letters duly bordred . Engraved portion painted of as per required colour/ approved colour (DUCO) of approved brand and filling with required matt/ mirror finish polish on base and border with shining polish of required shade and colour and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ nut bolt/ spacer required nos of holes, wherever required complete as per direction of Unit Incharge. (make Jindal or Equivalent)

Supply and fixing of Powder coated Aluminum Panel for directory of size 900mm x 750mm with partition of required Nos supported on aluminum channel 2 nos backiside with ACP sheet .Matter will Be digital print, matter covered with transprent polycarbonate sheet 0.5 mm wherever required completeand duly fixed with required nos of rawls plugs stainless steel srew/ spacer required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of Amuminium Silver powder coated signage of reqired size complete with message. Matter will be digital print written single sides, matter covered with transparent polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ screw required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of Amuminium Silver powder coated signage two plates ( vertical type) of reqired size complete with message. Matter will be digital print written both sides, matter covered with transparent polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ screw required nos of holes, wherever required complete as per direction of Unit Incharge

Providing & fixing of emergency sign boards single side of required size made of Photo luminescent film having glow power of 4 hours with message and graphics to be screen printing / vinyl cut film of 3M / Avery Denison / LG / Oracle or equivalent make to be pasted on 3mm thick Sun Board sheet all complete and duly fixed with required numbers of rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Unit Incharge

Providing & fixing of Glow-in-the-dark tape to mark safe lanes for pedestrians on the floors/ corridors to lead people to exit location. • Clearly visible in a dark room for 4 + hours • UV and chemical resistant • Strong adhesive Clearly designate aisle ways and emergency pathways in the dark condition. The surface should be cleaned thoroughly before sticking the tape with cleaning agents. Size: 4” Arrow size – green color.

Supply & Fixing Display notice pinup board of required size, aluminum beeding of 12 mm and fixed with required numbers of rawls plugs stainless steel srew as per direction of Unit Incharge.

Supply & Fixing Key ring holder stand of size 900mm x 600mm. Front door covered with transparent acyrlic shhet and locking arrangment. Fixed with required numbers of rawls plugs stainless steel srew as per direction of Unit Incharge.

Supplying and fixing of 18 gauge Stainless Steel Key Rings 1.245 mm thick (18 gauge) Stainless Steel plates of grade 304 etching (engraved)signage plate of Size 50mm x 38mm of and letters duly bordred as per sample approved and all as per sample. Engraved portion painted of as per required colour/ approved colour (DUCO) of approved brand written bth sides and filling with required matt/ mirror finish polish on base and border with shining polish of required shade and colour as per direction of Unit Incharge

Supply & placing of Stainless Steel 304 series Dustbin of size 300 x 175 as per direction of Unit Incharge.

Supply & placing of Stainless Steel 304 series Dustbin with foot operated of size 356 mm x 584 mm with plastic bucket as per direction of Unit Incharge.

Supplying of Q Manager made of hollow stainless steel pipe of 18 gauge and 900 mm high including 1.30 mtr and 50mm width long ribbon etc. all complete as per direction of Unit Incharge.

Provinding and fixing transparent logos/ Letters made out of etching tape 3M sparkle type on the lean glass surface with plain water, scraping glass before fixing film with blade, spray soap solution on glass squeeze excess water and air bubbles. All as directed of approved shape and sizes etc fixed with of required size as required as per direction of Unit Incharge. Make 3M/ Avery Denson

Supply & Fixing signages for exit of size 375mm x 200mm x 8mm in acrylic sheet LED light with battary backup

Supply & fixing of signboard made out of 3mm thick sun board with face fully covered with digital print of approved shade and make. The sign board should be fixing on wall,fixed with four rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Unit Incharge.

Supplying & fixing of retro reflective sign plates of required size. The plate made of High intensity prismatic grade type IV retro reflective sheeting of 3M / Avery Denison or equivalent make approved by I.R.C. / M.O.S.T. with message and graphics to be overlay film/High intensity prismatic grade type IV retro reflective sheeting of 3M / Avery Denison or equivalent make approved by I.R.C. / M.O.S.T Reflective tape of same make duly plotter cut, of approved color, letters (single side) in white colour, to be pasted on 3mm thick ACP sheet of make Alstone / Alstrong / Eurobond / Alucobond or equivalent etc. as per drawings. The sign boards shall fixeed on wall/ roof duly fixed with rawls plugs stainless steel srew/ double side tape 3M make/ SS chain of required size of required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of 18 gauge Stainless Steel plates with water jet cutting of grade 304 etching (engraved)signage plate of required size and letters duly bordred . Engraved portion painted of as per required colour/ approved colour (DUCO) of approved brand and filling with required matt/ mirror finish polish on base and border with shining polish of required shade and colour and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ nut bolt/ spacer required nos of holes, wherever required complete as per direction of Unit Incharge. (make Jindal or Equivalent)

Supply and fixing of Powder coated Aluminum Panel for directory of size 900mm x 750mm with partition of required Nos supported on aluminum channel 2 nos backiside with ACP sheet .Matter will Be digital print, matter covered with transprent polycarbonate sheet 0.5 mm wherever required completeand duly fixed with required nos of rawls plugs stainless steel srew/ spacer required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of Amuminium Silver powder coated signage of reqired size complete with message. Matter will be digital print written single sides, matter covered with transparent polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ screw required nos of holes, wherever required complete as per direction of Unit Incharge

Supply and fixing of Amuminium Silver powder coated signage two plates ( vertical type) of reqired size complete with message. Matter will be digital print written both sides, matter covered with transparent polycarbonate sheet 0.5mm. and duly fixed with required nos of rawls plugs stainless steel srew/ double side tape of 3M make/ screw required nos of holes, wherever required complete as per direction of Unit Incharge

Providing & fixing of emergency sign boards single side of required size made of Photo luminescent film having glow power of 4 hours with message and graphics to be screen printing / vinyl cut film of 3M / Avery Denison / LG / Oracle or equivalent make to be pasted on 3mm thick Sun Board sheet all complete and duly fixed with required numbers of rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Unit Incharge

Providing & fixing of Glow-in-the-dark tape to mark safe lanes for pedestrians on the floors/ corridors to lead people to exit location. • Clearly visible in a dark room for 4 + hours • UV and chemical resistant • Strong adhesive Clearly designate aisle ways and emergency pathways in the dark condition. The surface should be cleaned thoroughly before sticking the tape with cleaning agents. Size: 4” Arrow size – green color.

Supply & Fixing Display notice pinup board of required size, aluminum beeding of 12 mm and fixed with required numbers of rawls plugs stainless steel srew as per direction of Unit Incharge.

Supply & Fixing Key ring holder stand of size 900mm x 600mm. Front door covered with transparent acyrlic shhet and locking arrangment. Fixed with required numbers of rawls plugs stainless steel srew as per direction of Unit Incharge.

Supplying and fixing of 18 gauge Stainless Steel Key Rings 1.245 mm thick (18 gauge) Stainless Steel plates of grade 304 etching (engraved)signage plate of Size 50mm x 38mm of and letters duly bordred as per sample approved and all as per sample. Engraved portion painted of as per required colour/ approved colour (DUCO) of approved brand written bth sides and filling with required matt/ mirror finish polish on base and border with shining polish of required shade and colour as per direction of Unit Incharge

Supply & placing of Stainless Steel 304 series Dustbin of size 300 x 175 as per direction of Unit Incharge.

Supply & placing of Stainless Steel 304 series Dustbin with foot operated of size 356 mm x 584 mm with plastic bucket as per direction of Unit Incharge.

Supplying of Q Manager made of hollow stainless steel pipe of 18 gauge and 900 mm high including 1.30 mtr and 50mm width long ribbon etc. all complete as per direction of Unit Incharge.

Provinding and fixing transparent logos/ Letters made out of etching tape 3M sparkle type on the lean glass surface with plain water, scraping glass before fixing film with blade, spray soap solution on glass squeeze excess water and air bubbles. All as directed of approved shape and sizes etc fixed with of required size as required as per direction of Unit Incharge. Make 3M/ Avery Denson

Supply & Fixing signages for exit of size 375mm x 200mm x 8mm in acrylic sheet LED light with battary backup

Supply & fixing of signboard made out of 3mm thick sun board with face fully covered with digital print of approved shade and make. The sign board should be fixing on wall,fixed with four rawls plugs stainless steel srew/ double side tape of 3M make required nos of holes, wherever required complete as per direction of Unit Incharge.

TABLE FOR MEDICAL SUPRETENDANT AND DEPUTY SUPRETENDANT SIZE :- MAIN TABLE - 2400W X 800D X 780HT / SIDE TABLE - 1200W X 500D X 650HT. BACK STORGE - 1800W X 400D X 750HT. TABLE:- Modular table with work top made of 50mm thickness pre-laminated particle board of approve decorative color laminate on front and back side with white balancing laminate. lower part of the top will be encased with aluminium section edging .Pre-laminated particle board Modesty panel shall be 18mm thick prelam particle board (PLPB) clad with decorative laminate on both side , edges shall be sealed with pvc edge beading. Complete table having knock down system on kd fittings. Table shall have one hydraulic deskport with provision of power point, voice & data. etc. Work top shall be supported on side unit and Fixed drawer unit. SIDE TABLE:- side storage cabinet carcass , top made of 25mm thick and rest body like shelves , backand shutters shall be made up of 18mm thick Pre-laminated particle board with pvc edge beading on edges. BACK UNIT :- storage, Top made of 25mm thick and rest body made of 18mm thick three layer prelaminated particle board of approve decorative color laminate on front. Storage will have swing shutters on soft closing hinges with locking system ,adjustable shlef in storage for keep file according to user, all panels shall be of 18mm thick prelam particle board of 18mm thickness , edges dully sealed with pvc edge beading . Complete knock down system . Storage with lock and handels. The products should be as per BIFMA standards. The boards used sholud meet international standards of quality and safety, indian standard IS 12823 grade II.

TABLE FOR PRINCIPLE / VICE PRINCIPLE / MATRON / MEDICAL OFFICER MODEL:- SENATE SIZE :- MAIN TABLE - 2400W X 800D X 780HT / SIDE TABLE - 1200W X 500D X 650HT. BACK STORGE - 1800W X 400D X 2000HT. TABLE:- Modular table with work top made of 25mm thickness pre-laminated particle board of approve decorative color laminate on front and back side with white balancing laminate. lower part of the top will be encased with aluminium section edging .Pre-laminated particle board Modesty panel shall be 18mm thick prelam particle board (PLPB) clad with decorative laminate on both side , edges shall be sealed with pvc edge beading. Complete table having knock down system on kd fittings. Table shall have one hydraulic deskport with provision of power point, voice & data. etc. Work top shall be supported on side unit and Fixed drawer unit. SIDE TABLE:- side storage cabinet carcass , top made of 25mm thick and rest body like shelves , backand shutters shall be made up of 18mm thick Pre-laminated particle board with pvc edge beading on edges. BACK UNIT :- storage, Top made of 25mm thick and rest body made of 18mm thick three layer prelaminated particle board of approve decorative color laminate on front. Storage will have swing shutters on soft closing hinges with locking system ,adjustable shlef in storage for keep file according to user, all panels shall be of 18mm thick prelam particle board of 18mm thickness , edges dully sealed with pvc edge beading . Complete knock down system . Storage with lock and handels. The products should be as per BIFMA standards. The boards used sholud meet international standards of quality and safety, indian standard IS 12823 grade II

TABLE FOR CM OFFICER / HOD / MATRON / MEDICAL OFFICER MODEL :- SENATE TABLE - 501 SIZE :- MAIN TABLE - 2200W X 800D X 780HT / SIDE TABLE - 1050W X 500D X 650HT. BACK STORAGE:-1800WX450DX2000HT TABLE:- Modular table with work top made of 40mm thickness pre-laminated particle board of approve decorative color laminate on front and back side with white balancing laminate. lower part of the top will be encased with aluminium section edging .Pre-laminated particle board Modesty panel shall be 18mm thick prelam particle board (PLPB) clad with decorative laminate on both side , edges shall be sealed with pvc edge beading. Complete table having knock down system on kd fittings. Table shall have one hydraulic deskport with provision of power point, voice & data. etc. Work top shall be supported on side unit and Fixed drawer unit. SIDE TABLE:- side storage cabinet carcass , top made of 25mm thick and rest body like shelves , backand shutters shall be made up of 18mm thick Pre-laminated particle board with pvc edge beading on edges. BACK UNIT :- storage, Top made of 25mm thick and rest body made of 18mm thick three layer prelaminated particle board of approve decorative color laminate on front. Storage will have swing shutters on soft closing hinges with locking system ,adjustable shlef in storage for keep file according to user, all panels shall be of 18mm thick prelam particle board of 18mm thickness , edges dully sealed with pvc edge beading . Complete knock down system . Storage with lock and handels. The products should be as per BIFMA standards. The boards used sholud meet international standards of quality and safety, indian standard IS 12823 grade II

TABLE FOR SPECIAL EXAM ROOM / CONSULTION / PATHOLOGIST / NUTRITIONIST / STORE / INCHARGE / COUNSELLING ROOM / ANESTHESIA / CONSULTANT / PROFESSOR / ASSISTANT PROFF / ASSOCIATE PROFESSOR / LIBRARIAN / ASSISTANT LIBRARIAN MODEL : - CONCLAVE SIZE: - MAIN TABLE- 1800W X 800D X 760HT / SIDE TABLE: - 1200W X 400D X 620HT. TABLE:- Modular table with work top made of 40mm thickness pre-laminated particle board of approve decorative color laminate on front and back side with white balancing laminate. lower part of the top will be encased with aluminium section edging .Pre-laminated particle board Modesty panel shall be 18mm thick prelam particle board (PLPB) clad with decorative laminate on both side , edges shall be sealed with pvc edge beading. Complete table having knock down system on kd fittings. Table shall have one hydraulic deskport with provision of power point, voice & data. etc. Work top shall be supported on side unit and Fixed drawer unit. SIDE TABLE:- Side storage cabinet carcass , top made of 25mm thick and rest body like shelves , backand shutters shall be made up of 18mm thick Pre-laminated particle board with pvc edge beading on edges.

CABIN TABLE FOR RADIOLOGIST / CASHIER / ASSISTANT / NHM OFFICE /AAY OFFICE / PA / SECRETARY / OFFICE AREA / AV ROOM MAIN TABLE : 1600W X 750D X 750HT SIDE STORAGE:- 900W X 450D X 750HT Specification : Table top : 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Support : Supported on 25 mm thickPLB Gable ends & neccessary brackets. Modesty Panel : 18mm thick modesty panels of 450HT is considered. Wire Management : Grommet hole is considered for data & wire management. Side Storage : Storage is made of 18mm PLB with openable shutters, adjustable shelves, auto closing hinges, locking mechanism and recessed handles.

CABIN TABLE FOR MICROSCOPY / DUTY DOCTOR / ULTRASOUND ROOM / MAIN TABLE : 1200W X 600D X 750HT Specification : Table top : 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Support : Supported on 25 mm thickPLB Gable ends & neccessary brackets. Modesty Panel : 18mm thick modesty panels of 450HT is considered. Wire Management : Grommet hole is considered for data & wire management.

HEAD CHAIR FOR MEDICAL SUPRETENDANT AND DEPUTY SUPRETENDANT MODEL:-CROWN 1 High Back Chair with Leather Upholsted cushioned Seats and PU moulded armrest.The knee-tilt multilock mechanism makes you feel like you are sitting on a cushion of air as it creates a smooth and balanced feel as you move from one position to the next Push the left-side lever up/down to unlock/lock reclining at multiple positions.

VISITOR CHAIR FOR MEDICAL SUPRETENDANT AND DEPUTY SUPRETENDANT MODEL:-CROWN 2 Mid Back Chair with Leather Upholsted cushioned Seats and PU moulded armrest.The knee-tilt multilock mechanism makes you feel like you are sitting on a cushion of air as it creates a smooth and balanced feel as you move from one position to the next Push the left-side lever up/down to unlock/lock reclining at multiple positions.

HEAD CHAIR FOR JUDGE/SOLICITER GENERAL/REGISTRAR GENERAL MODEL:- INVENTION HB High Back Chair with Leather Upholsted cushioned Seats and PU moulded armrest.The knee-tilt multilock mechanism makes you feel like you are sitting on a cushion of air as it creates a smooth and balanced feel as you move from one position to the next Push the left-side lever up/down to unlock/lock reclining at multiple positions.

VISITOR CHAIR FOR JUDGE/SOLICITER GENERAL/REGISTRAR GENERAL/CONFERENCE ROOM MODEL:- INVENTION MB Mid Back Chair with Leather Upholsted cushioned Seats and PU moulded armrest.The knee-tilt multilock mechanism makes you feel like you are sitting on a cushion of air as it creates a smooth and balanced feel as you move from one position to the next Push the left-side lever up/down to unlock/lock reclining at multiple positions.

MODEL:- TYCOON HIGH BACK HEAD CHAIR FOR CM OFFICER / HOD / MATRON / MEDICAL OFFICER High back Chair with cushioned back Leather upholsted cushioned seat ,fixed armrest aluminium diecast,PU padded armrrest,synchro tilt mechanism,with metal base and castors.

MODEL:- TYCOON MID BACK VISITOR CHAIR FOR CM OFFICER / HOD / MATRON / MEDICAL OFFICER Mid back Chair with cushioned back Leather upholsted cushioned seat ,fixed armrest aluminium diecast,PU padded armrrest,synchro tilt mechanism,with metal base and castors.

HEAD CHAIR FOR SPECIAL EXAM ROOM / CONSULTION / PATHOLOGIST / NUTRITIONIST / STORE / INCHARGE / COUNSELLING ROOM / TREATMENT ROOM PROFESSOR / ASSISTANT PROFF / ASSOCIATE PROFESSOR / LIBRARIAN MODEL:- INVENTION LEATHERETTE High Back Chair with Leatherette Upholsted cushioned Seats and PU moulded armrest.The knee-tilt multilock mechanism makes you feel like you are sitting on a cushion of air as it creates a smooth and balanced feel as you move from one position to the next Push the left-side lever up/down to unlock/lock reclining at multiple positions.

VISITOR CHAIR FOR SPECIAL EXAM ROOM / CONSULTION / PATHOLOGIST / NUTRITIONIST / STORE / INCHARGE / COUNSELLING ROOM TREATMENT ROOM PROFESSOR / ASSISTANT PROFF / ASSOCIATE PROFESSOR / LIBRARIAN FOR A PROFF READER MODEL:- INVENTION VA Visitor Chair with Leatherette Upholsted cushioned seat and back with PU padded cushioned armrest and chrome plated metal sledge base.

HEAD CHAIR FOR PA/PS/CASHIER/ ASSISTANT / NHM OFFICE / OFFICE AREA MODEL:- CLICK HB The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards.Gaslift - Class 4 tested -ANSI BIFMA performance standards.This mechanism is manufactured out of cold Rolled Carbon Steel IS 513-1994 Sheets,The steel components are manufactured with highly precision tools For accuracy in matching other parts for smooth functioning. The steel components are fabricated by using Co2 welding process for giving uniform surface finish with higher tensile strength. Springs are made out of Grade II material. Composite release levers for locking mechanism & Gas lift height adjustment. Release lever mechanism for Locking and Gas lift height adjustment. Double Padded Cushioned Back with LEATHERETTE Upholstery

VISITOR CHAIR FOR PA/PS/CASHIER/ ASSISTANT / NHM OFFICE / OFFICE AREA MODEL:- CLICK VA Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards.This mechanism is manufactured out of cold Rolled Carbon Steel IS 513-1994 Sheets,The steel components are manufactured with highly precision tools For accuracy in matching other parts for smooth functioning. The steel components are fabricated by using Co2 welding process for giving uniform surface finish with higher tensile strength. Springs are made out of Grade II material. Composite release levers. Double Padded Cushioned Back with LEATHERETTE Upholstery

MODEL:- CHROME LEATHERETTE HB High Back Chair with Leatherette Upholsted cushioned padded Seats and back, fixed metal armrest.The knee-tilt multilock mechanism makes you feel like you are sitting on a cushion of air as it creates a smooth and balanced feel as you move from one position to the next Push the left-side lever up/down to unlock/lock reclining at multiple positions.

MODEL:- CHROME LEATHERETTE MB Mid Back Chair with Leatherette Upholsted cushioned padded Seats and back, fixed metal armrest.The knee-tilt multilock mechanism makes you feel like you are sitting on a cushion of air as it creates a smooth and balanced feel as you move from one position to the next Push the left-side lever up/down to unlock/lock reclining at multiple positions.

MODEL:- CHROME LEATHERETTE VA Mid Back Chair with Leatherette Upholsted cushioned padded Seats and back, fixed metal armrest.

MODEL:- ICON FOR WORKSTATIONS / RECPTIONS / MICROSCOPY / DUTY DOCTOR / ULTRASOUND ROOM Mid back chair with CUSHION back fabric upholsted cushioned seat and adjustable lumbar support. The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards. Upholstery: Seat Cushion with pre moulded foam of 50 - 60 density Density -- 52 kg/m3 Hardness -- 12.6kgf at 25%

CHAIR FOR READING ROOM / MAGZINE ROOM / JOURNAL ROOM MODEL:-VERSA MB Seat and back is made out of 12mm molded hot pressed plywood in ergonomic shape fitted with Imported T-nuts and revited in to the wood.The 640mm dia (26 inches) five pronged base is made out of GF nylon – Reinforced with bottom ribbing for additional buttress and strength. Tested prudently and rigorously as per ANSI/BIFMA X5.1-2011 General Purpose Office Chair Standards.Self Calibrating Multilock Mechansim Tested as per BIFMA Standards..Back Frame is upholstered with Thinner Mesh Adjustable Lumbar Support Allows you to adjust the lumbar support position for good back support and blood circulation.Moulded self skinned polyurethene Arms confirming to IS 7078 with steel insets for long life. one way adjustable - Height Adjustable.

VISITOR CHAIR FOR ULTRASOUND ROOM / NON TEACHING STAFF The frame is made out of 25.4mm tube of 16 gauge tube confirming to IS-7138- 1973, Welded by Co2 welding process for uniform surface finish.Thermo set powder coating epoxy polyester hybrids of hardness (pencil) H.B.74 and impact resistant (in lab) 60- 160 kgs cm and to a thickness of 40-50 microns is carried out of 7 step pretreatment process.High quality metal hardware conforming to Hardness 38-44 and tensile strength – 1300 n/mm. IS 1363 1967.Upholstery Cushion with pre moulded foam of 50 - 60 ensity in the shape of plywood. DEnsity -- 52 kg/m3 Hardness -- 12.6kgf at 25%.Polypropylene injection moulded armrests - Fixed Arms.

WRITTING DESK CHAIR FOR DEMO ROOM MODEL: RADDON WD Powder coated metal body design finished in matte black.The frame is made out of 22mm tube of 16gauge tube Welded by Co2 welding process for uniform surface.The Back Shell is made out of Talc filled 10% poly propylene co polymer molded with ergonomic see through design.High quality metal screws and tension fasteners conforming to Hardness 38-44 and tensile strength For maintenance free usage with international styling molded self skinMesh Tray Made out of PCL synomate ABS/PC alloy grade M-850 jet back.

AUDITORIUM CHAIR MODEL:-VENUS Upholstered mono-block with central feet which is fixed to the upholstered sides with a steel frame. Upholstered backrest finish. Seat and back moulded polyurethane self-extinguishing foam (60-65 kg/m3), ergonomics. Great comfort. Wide variety of finishes. M1and M2 fire barrier. Arms lined-up seats. Silent folded mechanism of the seat. Steel frame that fixes the seat, sides and back. Central edestal is moulded aluminium epoxy finish. Fixed to floor with a steel plate. Seats could be numbered (optional) with writting desk.

MODEL:- KD21532 SOFA 2 SEATER FOR MEDICAL SUPRETENDANT AND DEPUTY SUPRETENDANT SIZE:- 1780W X 1000D X 810HT The sofa offers a wide array of options for combining veneers, upholstery, and accent materials to allow the versatile design to precisely fit a range of environmentsTo achieve the right look for the wood veneer shell, an intricate miter is incorporated at every corner, allowing the molded veneer to wrap completely around the sides and back. There is only one seam on the entire shell.The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered with Half Leather.Back Foam: The Back is made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 23+/- 2 kg/cu.mtr, Backis upholstered with half Leather. understructure: unterstructure is made up of 1.2+/- 0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube and plate.

CENTER TABLE FOR MEDICAL SUPRETENDANT AND DEPUTY SUPRETENDANT Center Table with Glass/ Stone Top with Chrome Slimline Frame

CENTER TABLEFOR MEDICAL SUPRETENDANT AND DEPUTY SUPRETENDANT Corner Table with Glass/ Stone Top with Chrome Slimline Frame

MODEL:- KD9472 SOFA 2 SEATER FOR PRICIPLE AND VICE PRINCIPLE SIZE:- 1420W X 750D X 820HT The sofa offers a wide array of options for combining veneers, upholstery, and accent materials to allow the versatile design to precisely fit a range of environmentsTo achieve the right look for the wood veneer shell, an intricate miter is incorporated at every corner, allowing the molded veneer to wrap completely around the sides and back. There is only one seam on the entire shell.The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Leather.Back Foam: The Back is made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 23+/- 2 kg/cu.mtr, Backis upholstered wuth Fabric or Leatherite. understructure: unterstructure is made up of 1.2+/- 0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube and plate.Sofa sould have BIFMA certified.

CENTER TABLE FOR PRICIPLE AND VICE PRINCIPLE Center Table with Glass/ Stone Top with Chrome Slimline Frame

SIDE TABLE FOR PRICIPLE AND VICE PRINCIPLE Corner Table with Glass/ Stone Top with Chrome Slimline Frame

MODEL:- INDULGE 2 SEATER SOFA FOR SM OFFICER / DOCTOR LOUNGE Fabric upholsted cushioned sofa with chrome plated metal legs.sofa-Width: 1400 mm Depth:750 mm Height: 735mm cm Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Fabric.Back Foam: The Back is made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 23+/- 2 kg/cu.mtr, Backis upholstered wuth Leatherite. understructure: unterstructure is made up of 1.2+/- 0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube.

CENTER TABLE FOR CM OFFICER / DOCTOR LOUNGE Size: 1100(W) x 525(D) x 425(H) This high molded plywood table has natural face veneers and hardwood inner plies. It has a 5-ply, 34"‑diameter top and an 8-ply 4-leg base. Shipped knocked down.

SIDE TABLE FOR CM OFFICER / DOCTOR LOUNGE Size: 501(W) x 501(D) x 505(H) This high molded plywood table has natural face veneers and hardwood inner plies. It has a 5-ply, 34"‑diameter top and an 8-ply 4-leg base. Shipped knocked down.

SOFA FOR HOD / CONVERSE 3 SEATER sofa-Width: 1800 mm Depth:750 mm Height: 820mm cm Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Leatherette.Back Foam: The Back is made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 23+/- 2 kg/cu.mtr, Backis upholstered wuth Leatherite. understructure: unterstructure is made up of 1.2+/- 0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube.

SOFA FOR HOD / PROFESSOR / LIBRARIAN CONVERSE 2 SEATER sofa-Width: 1375 mm Depth:750 mm Height: 820mm cm Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Leatherette.Back Foam: The Back is made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 23+/- 2 kg/cu.mtr, Backis upholstered wuth Leatherite. understructure: unterstructure is made up of 1.2+/- 0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube.

CENTER TABLE FOR DOCTOR LOUNGE / HOD / PROFESSOR Center Table with wooden frame and structure with Glass top and High end polished finish.

SIDE TABLE FOR DOCTOR LOUNGE / HOD Center Table with wooden frame and structure with Glass top and High end polished finish.

SOFA FOR OT PREPERATION AREA PEARL 3 SEATER sofa-Width: 1800 mm Depth:750 mm Height: 735mm cm Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Leatherette.Back Foam: The Back is made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 23+/- 2 kg/cu.mtr, Backis upholstered wuth Leatherite. understructure: unterstructure is made up of 1.2+/- 0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube.

SOFA FOR NURSE LOUNGE / STAFF LOUNGE / PRIVATE ROOM PEARL2 SEATER sofa-Width: 1800 mm Depth:750 mm Height: 735mm cm Seat Foam: The Seat is made of PU Foam with Density 32+/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 28+/- 2 kg/cu.mtr, Seat is upholstered wuth Leatherette.Back Foam: The Back is made of PU Foam with Density 28 +/- 2 kg/cu .mtr having an additional top layer of PU Foam with Density 23+/- 2 kg/cu.mtr, Backis upholstered wuth Leatherite. understructure: unterstructure is made up of 1.2+/- 0.1cm thick hote pressed plywood , 4mm Dia zigzag Spring is mounted in the understructure for support and additional cushioning purpose. Leg Assembly: is welded assembly made in SS 202 Grade tube.

CENTER TABLE FOR NURSE LOUNGE / STAFF LOUNGE / PRIVATE ROOM MODEL: CRYSTAL CRYSTAL Table size 1200 x 600 x 505 mm made of 22mm steel frame duly chromeplated and glass top. Legs of table are made up of oval metal tube having silver powder coating having thickness of 1.5mm.Top glass is partial tempered glass of size 1200mm dia.Top glass is fitted with legs with the help of UV discvis ultrasonic welding.

CORNER TABLE FOR NURSE LOUNGE / STAFF LOUNGE / PRIVATE ROOM MODEL: CRYSTAL CRYSTAL Table size 600 x 600 x 505 mm made of 22mm steel frame duly hromeplated and glass top. Legs of table are made up of oval metal tube having silver powder coating having thickness of 1.5mm.Top glass is partial tempered glass of size 1200mm dia.Top glass is fitted with legs with the help of UV discvis ultrasonic welding.

LINEAR WORKSTATIONS SIZE:-1350mm W X 600mm D x 750mm H and 1200mm HT Partition MOBILE PEDESTAL:- 400W X 450D X 600HT Table Top - 25mm thick Pre laminate particle board with 2mm PVC edge lipping. Support - 18mm thick Pre lam gable ends. Wiremanagement -One metal raceway tile to mount switches below table top level for power and skirting tile for data by default.Grommet hole is considered for each workstation. PARTITION:-Partition is made of 50mm thick NEO based system with fabric magnetic above and lamiante below the table top. Fabric magnetic and glass markers are provided for each table. Outside tiles would be laminate tiles. Grouting Post are provided for additional support.

LINEAR WORKSTATIONS SIZE:-1500mm W X 600mm D x 750mm H and 1200mm HT Partition MOBILE PEDESTAL:- 400W X 450D X 600HT Table Top - 25mm thick Pre laminate particle board with 2mm PVC edge lipping. Support - 18mm thick Pre lam gable ends. Wiremanagement -One metal raceway tile to mount switches below table top level for power and skirting tile for data by default.Grommet hole is considered for each workstation. PARTITION:-Partition is made of 50mm thick NEO based system with fabric magnetic above and lamiante below the table top. Fabric magnetic and glass markers are provided for each table. Outside tiles would be laminate tiles. Grouting Post are provided for additional support.

LINEAR WORKSTATIONS SIZE:-1650mm W X 600mm D x 750mm H and 1200mm HT Partition SIDE STORAGE:- 900W X 450D X 640HT Table Top - 25mm thick Pre laminate particle board with 2mm PVC edge lipping. Support - 18mm thick Pre lam gable ends. Wiremanagement -One metal raceway tile to mount switches below table top level for power and skirting tile for data by default.Grommet hole is considered for each workstation. PARTITION:-Partition is made of 50mm thick NEO based system with fabric magnetic above and lamiante below the table top. Fabric magnetic and glass markers are provided for each table. Outside tiles would be laminate tiles. Grouting Post are provided for additional support.

SIZE:- 9200WX 3000 D X 7 X750HT CONFERENCE TABLE U SHAPE Specification: Table top - 25mm thick Pre-laminate particle board finished with 2mm edge lipping. Support - Supported on 25 mm thick Gable ends and necessary brackets. Modesty Panel - 18 mm thick PLT Modesty Panel of 450 mm ht is considered. Wire Manageement - Flip up 450 with provision for Switch cut out are provided for power and data cable management. Vertical Wire entry Cover is considered.

STORAGE FOR NON TEACHING STAFF / DEPT OFFICE STORAGE:- 900L X 450D X 1200HT The structure is made out of 18mm Thick Pre-Laminated Particle Board. The Shelves are adjustable in height. The shutters are fitted with auto closing hinges. Recessed Aluminum handles, central locking system , levellers & other necessary hardware are priovided.

TABLE FOR CANTEEN 900DIA Table for whose top is made of Particle board wood Grade E-1(Environmental Friendly), thickness 25mm cover with Melamine, Edge banding (PVC) 2mm.E1 grade 1mm laminate with zero urea formaldehyde emissions (<or= 8mg/100 g oven dry board-perforated method) for better in-house quality. This should comply with (EN 120-1992).The understructure is made of Steel square pipe dimension 38 X 38mm. Thickness 2.5mm. Epoxy powder coated spray paint, baked at temperature 200 C° coated of 70-80 micron thickness.Table sould have Green Guard certificate and BIFMA certified.

CANTEEN CHAIR MODEL:- EVES Stackable chair without arms made up of Pre colored PP+GF20% ( 20% short glass fibre reinforced polypropylene) using injection moldeing having chrome plated metal supports and legs.

BENCHES FOR WATING 2 seater made up of MS poder coated rectangular M.S.ERW tube having 8=0.03cm X 4=0.03cm x 0.2+0.016cm size. Kegs & armrest-it is chrome plate made of cold steelwith 0.12+0.013cm thickness saet back shell it is 1.6mm thk powder coated perforated shell made from cold rolled S.S. sheet 0.16+0.013cm thickness. the side bar is made of chrome plated solid steel 3+0.03cm X 1.2+0.3cm(DIN174) with fluting and plastic inserts. the shell is asembled on the cross beam with help of MB bolts per seat- 8nos. seat to bracket.

TABLE FOR NON TEACHING STAFF / READING ROOM / MAGZINE ROOM / JOURNAL ROOM MODEL:-PERFORM SIZE- 1500W X 900D X 750HT Specifications: Table top - 25mm thick Pre-laminated particle board finished with 2mm PVC edge lipping. Under Structure - Powder coated MS 50x50mm square Legs & Supporting MS 40x20mm Beams. Wire Management - 1 NOS of 450 mm Flipup for Power and Data and Vetebra for Wire Entry.

BOOK SHELVES FOR JUDGE LIBRARY SIZE:- 900W X 400DX1800HT The outer structure is made out of 18mm prelaminated boards (PLB). The back of the unit is made from 9mm PLB. The shelves are made out of 18mm PLB, which are adjustable in height. With Pivot Glass Shutters.

Reception Table - 2400mmL X 600mmD X 750mm/1050mmH Table Top made up of 18 mm thick Granite top & under sturcture is made up of 19 mm thk. commercial plyboard with Laminte as per approvel color. . Gable end & Side is made up of 19mm thk. commercial plyboard wtih 1.0 laminate past on ply board.. All Exposed edges are sealed with PVC edge-band of 2 mm thickness & Non-exposed edges are sealed with 0.45 mm thick Edge-band from REHAU.

BOOK STORGAE, MODEL:- 4-Door Book Case SIZE:-1500W X 300D X 900HT Book case having 4 no. Shelves with front transparent glass.Door would thickness of 18-20guage having transparent 5mm float glass and rest body 20-22 guage.

BED FOR DUTY DOCTOR SIZE:- 2000L X 900D X 450D / 1000HT Structure shall be of plywood with veneer finish. the edges of the plywood veneered surfaces shall be having solid wood edge lipping. the reepers shall be of hardwood with polish finish. the legs shall be of solid wood with melamine polish matt finish.

Tribeni Constructions Limited