Special repairs to laboratories at NCS Goa and Special repair to two security watch tower P 46 and P 49 at MO Goa under GE Gomantak

Amount

Dismantling floor, hearth or wall tiling also in patches including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified.

M&L for 25 mm (average) thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in levelling course finished even and rough etc. complete all as specified and directed.

M&L for machine cut kota stone slab of size not less than 550 x 550 mm (except where lesser size required) as in flooring or in trades of steps (in single piece) 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing, rounding of edges and mirror finish polishing with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L glazed ceramic white tiles 300 x 200 x 6 to7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over 10 mm thick rendering in cement mortar 1:3 complete all as specified and directed.

Taking down cement plaster on walls/ceiling of any description including racking out joints hacking for key, scrubbing down with water etc. and removing rubbish complete all as specified and directed.

Providing and applying 15 mm thick ready mix external sand faced cement plaster with neat cement rendering at all locations in two coats on masonry and concrete surfaces including providing water proofing compound to the first coat of plaster as per manufacturers specification, racking out joints, hacking of concrete surface, finishing, curing, scaffolding etc complete all as specified & directed. (Rate of WPC deemed to be included under this item) Make : Asian paint/ ACC/ JK Cement/ ULTRATECH

Apply a coat of SmartCare Primero with dilution ratio of 1:1 with water maintain a coverage of 100 sq.ft/ltr complete all as specified & directed.

M&L for preperation of new surface wall/ceilling by scrapping/rubbing,applying two coat of advanced anti-algal weather proof 100% acrylic smooth emulsion with silicon additives,over a coat of fibre reinforced elastomeric liquid water proofing membrane (Asian paint damp proof+ultima suprema,exterior anti fungal paint or equivalent) , on new plastered surfaces walls/ceilling and cornires brooming down or steel wire brushing scrapping down with steel scrapper smoke soot moulds moss and efflorescent slats brading oil and greasy spots etc and making proper surface by applying ready mix preparatory wall care putty of Birla wall care or equivalent wherever required complete all as manufacturers instructions. (Manufatured by : Asian paints damp proof + Ultima suprma or Equivalents Make). Note The Application of paint to be done by the authorised applicators of asian paint or eqlt make and contractor shall submit a written gurantee with the authorized dealer of 8 years for any type of colour fading,peeling,flaking,growth of fungus,seepage of water through the paint applied area or any other damages to the paint). Also the dealer shall appoint a person to inspect and validate the application of the system in stage wise manner.

Chipping off existing loose, damaged concrete from RCC members of all affected RCC Columns, beams, slabs and chajjas on external and internal facades etc beyond main r/f.(if required in the opinion of the consultant), carefully with chisel and hammer including relieving structural members such as column, beam and slabs of their superimposed load partially or fully by provision of adjustable steel props, frames etc. Providing and applying "Rusticide SS' Rust passivator or equivalent as specified in the Brand names to existing r/f bars including wire brushing of r/f, cleaning, washing of concrete etc complete as directed. Providing and applying two coats of rust preventor slurry made out of "Polyalk Fixoprime" or equivalent as specified in the brand names and cement in proportion 1:1.5 to exising r/f bars as directed complete. Providing and applying bonding coat of slurry made out of "Polyalk EP" or equivalent as specified in the brand names and cement in proportion 1:1 to concrete and r/f substrates complete as directed. Providing and applying 'Polyalk EP' or equivalent as specified in the brand names. Polymer modified cement mortar in required porportion (1:5:15) to RCC members including hand packing, curing and making the surface rough for plastering complete all as specified and directed.

M&L for preperation of old surface wall/ceilling by scrapping/ rubbing, applying, two coat of advanced anti-algal weather proof 100% acrylic smooth emulsion with silicon additives,over a coat of fibre reinforced elastomeric liquid water proofing membrane (Asian paint damp proof+ultima suprema,exterior anti fungal paint or equivalent), on plastered surfaces walls/ceilling and cornires brooming down or steel wire brushing scrapping down with steel scrapper smoke soot moulds moss and efflorescent slats brading oil and greasy spots etc and making proper surface by applying ready mix preparatory wall care putty of Birla wall care or equivalent wherever required complete all as manufacturers instructions. (Manufatured by : Asian paints damp proof + Ultima suprma or Equivalents MAke). Note The Application of paint to be done by the authorised applicators of asian paint or eqlt make and contractor shall submit a written gurantee with the authorized dealer of 8 years for any type of colour fading,peeling,flaking,growth of fungus,seepage of water through the paint applied area or any other damages to the paint). Also the dealer shall appoint a person to inspect and validate the application of the system in stage wise manner.

M&L for applying 3 mm thick putty on ceilling surfaces and applying two coat of oil bond distemper including preparation the old surface complete all as specified and directed.

Taking down existing treatment along with PCC padding of any thickness incl removing old roof treatment of any type and roughening surfaces of old roof surface by picking, sweeping clean and washing down with water to remove dust etc. complete all as directed.

M& L for rendering/screed 15 mm thick on brick or concrete surface in CM 1:4 mixed with PidiProof 101 LW(+) of Dr fixit (Pidilite) or equivalant of STP No. 1 intergral water proofing admixture @ 200 ml/bag of cement as in padding on roof surface for correction of slope finished fair an even complete all as specified and directed. (Rate of Water proofing compound shall deemed to be included under this item).

Supplying and applying High build elastomeric waterproofing coating based on pure, hydrophobic polyurethane, cold applied of spray / brush applied, membrane with an elongation of 550% and tensile strength of 2.5 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C1305, no leakage upto 7 bars of water pressure as per DIN 1048, shore A Hardness of min. 45 as per ASTM D 2240. The system includes final base preparation, water based primer and applying SmartCare PU Magnum or approved equivalent in two to three coats to achieve a min. thickness of 1.2mm, etc. complete as per Manufacturere specifications and as directed.

M&L Replacement of steel reinforcement with TMT CSR bars of appropriate size where 20% of cross section is reduced including dismantling of rusted steel including application of rust converter FEOVERT and applying protective coating IPNET-RB complete all as specified and directed.

Providing and laying Super fluid microconcrete-Roffe crete (or equivalent as specified in the list of brand names) for repairs in beam bottoms, columns, slabs etc. including mixing with 5 mm to 10 mm size aggregates, water proof plywood/steel plate shuttering, pouring, tamping, consolidating, curing etc complete as per manufacturer's specification and consultant's instructions and minimum thickness not less than 30mm. Note : Shuttering to be mesured and paid Separately.

Use and waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, column , cantilevers, shelves, slabs including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for precast cement concrete block masonry, type C-1 (1:3:6) (20 mm graded aggregate) with solid blocks, exc 10 cm in width and setting in CM 1:6 complete all as specified and as directed.

M&L Plain Cement Concrete 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5m clear span, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M&L for applying two coats of cement base paint on new surfaces of walls including preparation of surface complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed.

M&L structural steel work with rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc and similar articles conforming to Fe-410-W (Gde E-250) quality-A complete all as specified and directed.

M&L for preparation of new painted steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed

Taking down Chowkhats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each including making good the wall surface complete all as specified and directed.

Taking down Chowkhats or frames exc. 1.50 Sqm and n.exc 4.00 Sqm each with shutters (without taking off shutters from the frames) and including making good the wall surfaces complete all as directed.

S&F aluminium powder coated frame and shutters for windows/ventilators sliding/ fixed/ openable type complete with necessary fittings such as two concealed lock for each window, roller etc and fixing all as speciefied and directed. Note : (a) The weight of rubber gasket beading will not be measured with the weight of aluminium shutters, glass will be measuerd and paid separately. (b) The rate quoted by the contractor shall also include necessary wheels for sliding shutters and hinges for side hung/top hung shutter as required at sight and concealed locks for windows. (c) The colour of powder coating shall be as approved by GE.

S&F glazing 4 mm thick sheet glass ordinary type including rubber beddings/gasket around glass panes complete all as specified and directed.

S&F aluminium anodised wire mesh of size 1.5 mm x 3 mm mesh, 20 Gauge thick in doors/window shutters complete all as specified and directed.

S&F Solid PVC frame (single rebated) size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100 x 8 sheet metal CSK screws complete all as specified and as shown on drawing. NOTE: Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.

M&L for providing factory made 25 mm thick 100% solid WPC (wood polymer composite) coloured laminated flush door shutter of required size comprising of virgin PVC resin of K value 57-60 (suspension grade), calcium carbonate and natural fibers (wood powders/ rice husk/ wheat husk (non toxic additives, made from extrusion process WPC foam single extruded (inner) with having minimum density not less than 650 Kg/cbm, having good screw holding capacity (Screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), Minimum Compressive Strength of 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance of spread of flame of class A category with Property of being Termite / borer free water / moisture proof and fire Retardant WPC to be Laminated with PVC foil of minimum 14 microns thick of approved design pasted on both faces of shutter and fixing with necessary full body threaded star headed counter sunk SS screw complete all as directed. Note :- Material test Certificate and authentication should be compulsory provided by the manufacturing company.

S&F anodized aluminium grill (anodized transparent or dyed to required shade according to IS 1868 with minimum anodic coating of grade AC 15 of approved design/pattern with approved standard section and fixed to the existing window frame with CP brass/stainless steel screws @ 200 mm C/C including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodized section all around the grill and opening if required complete all as required at site and as directed.

M&L for preparation of old painted steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

S&F butt hinges medium weight cold rolled mild steel 100 mm long (ISI marked) complete all as specified and directed.

S&F aluminium anodized, barrel tower bolt of extruded section, 150 mm (ISI marked) complete all as specified and directed.

S&F 150 mm long Aluminium handles, cast type (ISI marked) complete all as specified and directed.

Taking up or down 25 mm dia steel tubing and connection and removal from site complete all as specified and directed

Taking up or down 20 mm dia steel tubing and connection and removal from site complete all as specified and directed

Supply, fixing, laying & testing CPVC pipes 20 mm SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Supply, fixing, laying & testing CPVC pipes 25 mm SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Dismantling of PVC existing water tank of exc. 500 ltrs & not exc. 1000 ltr capacity including taking down from roof/staging and removing from site complete all as specified and directed.

S&F Rotational moulded Polyethylene (HDPE) Water Storage Tank 1000 Litre Capacity (Cylindrical Vertical with Closed Top), hoisted and fixed in Position all specified in MES Schedule Part-I, fixed with tank nipple, union, float valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 20 mm bore complete all as specified and directed.

S&F in repair chromium plated brass shower rose 125 mm dia with or without swival joints, with CP long shank including fixing to 15 mm dia pipe or union all as specified.

S&F in repair 20 mm dia brass chromium plated tubular towel rail, D type, 60 cm long between flanges with hooks fixed with rawl plug complete all as specified and directed.

S&F in repair vitreous china squatting pan Orissa pattern size 580 x 440 mm white with front or back inlet, integral foot rest including 'P' or 'S' trap and connection to trap and flushing pipe, anti syphonage and providing cement concrete bedding complete all as specified and directed.

S&F in repair vitreous china bowl urinal flat back of size 465 x 355 x 266 mm (minimum), white excluding flushing cistern, flush pipe and waste pipe but including grating and union for discharge pipe complete including providing and fixing plugs, beding urinal agianst wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed.

S&F in repair vitreous china wash hand basin white flat back size 550x 400 mm including two Nos angle iron brackets and 32mm dia brass CP waste coupling complete all as specified and directed

S&F in repair 15mm bore pillar taps, long nose fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 10 Ltrs capacity, PVC valveless, syphonic action type, low level flushing cistern moulded from virgin poly propylene, white, with inlet, ball valve, float and handle complete with all internal accessories and fixed to wall, PVC flush pipe 32 mm dia 90 cm long fixed properly to inlet of WC complete all as specified and directed

S&F in repair PVC connection 600 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers complete all as specified and directed.

S&F in repairs PVC flexible waste pipe, 32 mm bore, 900mm long suitable for wash hand basin/ sink complete with adapter all as specified and directed.

S&F in repair bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed.

S&F in repair angle/stop valve 15 mm nominal bore cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) floor trap, with CP grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) complete all as specified and directed.

S&F in repair PVC (SWR) pipe 110 mm bore, type 'A', single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed.

S&F in repair PVC (SWR) pipe 75 mm bore, type 'A', single socketed, in any length with rubber ring joints and jointed with approved adhesive laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends 110 mm bore any radius with rubber ring complete all as specified and directed.

S&F PVC (SWR) bends 75 mm bore any radius with rubber ring complete all as specified and directed.

S&F in repair curtain rod fancy type, made out of 25mm dia MS conduit pipe duly PVC sleeved, fancy type plastic finial, decorative type, fixed to ends of rod and mild steel prepainted/PVC coated brackets suitable to hold the drapery rod and fixed to wall with the help of 2 Nos 50 mm long steel screws and rawl plug, colour and pattern as approved by GE complete all as specified and directed.

S&F in repair soap dish, brass chromium plated, oval shaped of size 100 x 50mm (minimum), fixed to wall with PVC gully and CP screws complete all as specified and directed.

M&L for pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding fixed with self tapping screws including taking down existing GI sheet complete all as specified and directed.

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/ dense soil complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge not exc 63 mm, deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick Cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in sub base of floor etc. complete all as specified and directed.

M&L for machine pressed rubber moulded coloured chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick, with grey pigment cement and pigment, set, jointed and pointed in neat cement slurry in floors with & including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in benching, copings and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and directed.

M&L for Soakage wells 1.8 M dia X 3.0 M effective depth excavation, in any type of soil, returning filling, removal of surplus soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of 1:1.5:3 type A-1 using 20 mm graded stone aggregate concrete including intercepting chamber and screen chamber made of Brick masonary in CM 1:, RCC cover slab in 1:1.5:3 type A-1 using 20 mm graded stone aggregate/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats complete all as shown in Drg No. TD- 94007 Sheet 1/1 and all as specified and directed.

Removing building materials by truck or tractor with using of if necessary JCB machine and trolly load min 3.00 Cum each load including loading, unloading and stacking at the destination and depositing out side defence land complete all as specified and directed.

M&L for Acid resistant tiles 600 x 600 x 15 mm thick vitreous ceramic, unglazed conforming to IS 4457-1982 set, jointed and pointed in chemical resistant mortar, resin type conforming to IS : 4832 : Part-2 : 1969 , in floors complete all as specified and directed.

M&L for screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed.

M&L for rendering 10 mm thick in cement mortar 1:4 for fixing tiles/stone complete all as specified and directed.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in floors, steps, jambs, pillars, window cills, cooking platforms and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding and polishing the edges all as specified and as directed.

M&L for White vitreous china laboratory sink size 600 x 450 x 200 mm with plugs, washers and wastes including beding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe; upto 0.5 sqm each complete all as specified and directed.

Material &Labour for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges and cutting chases for concealed water tubing, and making good, cutting not exc 10 cm girth complete all as specified and directed.

S&F 20 mm bore single socketed high density polyethylene pipes (HDPE) of pressure rating 6 Kgf/cm2 fixed complete to walls, ceilings or laid in floors etc. with all fittings such as ends elbow, union, bend, reducer etc., complete all as specified and directed.

S&F in repair PVC (SWR) pipes 110 mm single socketed in any length with rubber ring joints as in rain water pipe fixed to walls including clamps complete all as specified and directed.

M&L for complete removal of existance treatment of wall and applying two coat of oil bound distemper over a coat of primer over 3 mm thick wall care putty in two layers and complete all as specified and directed

M&L for preparation the old surface of ceilling and applying two coat of oil bound distemper over a coat of chalk whitening complete all as specified and directed.

M&L for preparation of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed

Demolition of cement concrete reinforced of any description and in any location complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slabs (for man holes etc.), chajja, shelves etc. and similar works set in cement mortar 1:6 complete all as specified and directed.

Demolition of Brick Work/ sone work / concrete block wall built in Cement Mortar including all quoins, arches, pillars, etc. of any descriptions, complete all as specified and as directed.

M&L for precast cement concrete block masonry, type C-1 (1:3:6) (20 mm graded aggregate) with solid blocks, exc 10 cm in width and setting in CM 1:6 complete all as specified and as directed.

M&L for Mild steel TMT bars 6 to 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

M&L for rendering 10 mm thick on brick or concrete surfaces in CM 1:6 finished fair and even complete all as specified and directed.

Supply & fix 18 mm thick Rajshree Celuls ply or equivalent as approved of grade 1 quality with one side plain and other side coloured fixed with stainless steel screws, solvent cement/adhesive to inside the shutter including hinges, magnetic ball catch and SS Handle & other all fitting as per manufacturer instructions and all as directed. Note : Rates included for SS handle 100 mm long- 01 No each shutter, SS Hinges-02 Nos each shutter and magnetic ball catch- 01 No each shutter

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

M&L for point wiring complete for one light/fan fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including minimum 20 mm dia 'medium grade' PVC concealed conduits ISI marked and fittings and replacement of modular metal flush box, modular white cover plate with frame, blanking plate and making good to the disturbed surfaces to match the existing complete all as specified and directed including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories including cutting chases for concealed piping and making good disturbed surface to match the existing surface complete all as specified and directed. Note- (i) Rates include the cost of blanking plate, modular plate, modular boxes and covers of suitable modules as required at site. (ii) Modular box, plate and cover shall be of same make as of switch//socket/regulator.

All as per item No. 91 above but for one 5 pin 5/6 Amp socket outlet point on an independent board.

All as per item No. 91 above but for one 5 pin 5/6 Amp socket outlet point on same board

All as per Item No 91 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 4 Sqmm and green colour earth cable of size 4 Sqmm.

S&F modular type switch one way 6 Amps, 230 Volt, 1 Module complete all as specified and directed.

S&F modular type switch one way 16 Amps, 230 Volt, 1 Module complete all as specified and directed.

S&F modular type switch socket combination one way 6 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed.

S&F modular type switch socket combination one way 6/16 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed.

S&F modular type socket one way 6 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed.

S&F modular type socket one way 6/16 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50 mm dia complete all as specified and directed.

S&F in replacement MCB single pole 240 volts, 'B' curve of rating from 6 to 32 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement MCB single pole 240 volts, 'C' curve of rating from 16 to 32 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement MCB SPN 240 volts, 'B' curve of rating 6 to 32 Amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement MCB SPN 240 volts, 'C' curve of rating 63 Amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection SPN, 240 Volts, 12 way, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection SPN, 240 Volts, 8 way, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed.

S&F in replacement existing U/S light fitting with LED tube light fitting surface mounted integrated type with 20 watt LED having minimum 100 lumens/watt electronic driver complete with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed.

S&F in replacement existing U/S light fitting with LED tube light fitting surface mounted integrated type with 10 watt LED having minimum 100 lumens/watt electronic driver complete with all accessories prewired and including making connections with 3 core twisted flexible copper cable of size 23/.0076 from ceilling rose/PVC connector to light fittings complete all as specified and directed.

S&F in replacement existing U/S light fitting with Recess mounting LED fittings 36 watts, suitable for 600 mm x 600 mm (2ftx2ft) modular/POP/Gypsum ceiling, luminaire with white powder coated CRCA housing with LEDs. seamless front frame with fat white high transmission acrylic cover 230V, complete in all respect & accessories internally prewired including connecting up with twin core copper twisted flexible copper conductor cable complete all as specified and directed.

S&F modular type fan regulator, electronic step type, 230 Volt, 2 Module complete all as specified and directed.

S&F ceiling fan 1200 mm sweep complete with blades and other accessories, single phase, 230 V, BEE 5 star rating and making connection with flexible wire 23/0.076 mm including connecting rod upto 2 m lenght complete all as specified and directed.

S&F brushless direct current (BDLC) ceiling fan 1200 mm sweep, minimum air delivery 230 CMM with service value 6.00 BEE, 5 star rating complete with blades and other accessories, single phase, 230 V and making connection with sheathed 3 core cable of size 0.75 Sqmm flexible copper conductor wire complete all as specified and directed.

S&F exhaust fan of 300 mm sweep, AC single phase 230/240 volts, heavy duty complete including making electric connection with PVC insulated three core 1.5 Sqmm copper cable from ceiling rose to exhaust fan, grouting anchor bolts/fastners and making good to disturbed surfaces to match the existing complete all as specified and directed.

S&F wall mounting fan 400 mm sweep complete with blades and other accessories, single phase, 230 V, 5 star rating including taking out old wall fan and deposited to MES store yard complete all as specified and directed.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4 sqmm nominal cross sectional area and one run of 4 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 25 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 2.5 sqmm nominal cross sectional area and one run of 2.5 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 25 mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings including cutting chases to walls for laying conduit and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.

M&L for earthing complete with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron Wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl 15 mm GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5 mm graded stone aggregate reinforced with 6 mm dia round bar @ 75 mm C/C both ways with MS handle 8 mm dia, plastering 15 mm thick CM (1:6) externally upto 150mm below ground level, GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl. excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No 3 of SSR Part (2009) and connected to earth test point incl testing complete all as specified an directed.

JINTECH

SHIVRAJ CONSTRUCTIONS

M/S DUBAL CONSTRUCTION

M/S Kartik Enterprises

Super Construction

Leela Enterprises

M/S. NAVEEN ENGINEERING & CO