SPL REP TO SEWAGE SYSTEM AND PROVN OF WATER SUPPLY FROM NAGAR NIGAM AT 755 I TPT PROVN OF REST ROOM AND MODERNIZATION OF COOK HOUSE AT 436 COY PROVN OF GALVALUME SHEET AT ECHS POLYCLINIC AND PROVN OF COVER SHED AT MH BHOPAL UNDER GE BHOPAL

Amount

Note :(i) Please refer Sch A/ BOQ Notes before quoting the tender for all phases/ items mentioned below. (ii) Amount of Schedule of credit shall be deducted offline

Surface excavation n exc 30 cm deep and averaging 15 cm deep and getting out in hard/ dense soil complete all as specified and directed.

Excavation over areas n.exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

All as per item No. 2.00 here-in-before but for each additional 1.5m or part thereof in depth beyond the first 1.5 m.

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth; for foundations etc. or for shafts, well cess pits, manholes, pier holes, etc. but n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

All as per item No. item No. 4.00 here-in-before but for each additional 1.5m or part thereof in depth beyond the first 1.5 m.

M&L for plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in foundations including rafts, footings, foundation beams, plinth beams, base for columns and mass concrete etc complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in columns, pillars, piers, posts and struts etc complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5 m span etc. complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregate) as in chajjas and similar work complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregates) in slabs supported on walls, beams & columns complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B1 in beam columns, deck, slab and like complete all as specified and directed.

M&L for reinforced cement concrete nominal mix 1:2:4 type B1 (using 20 mm graded stone aggregates) in domes, vaults, shell roofs, arch ribs and folded plates complete all as specified and directed.

Use and waste for formwork to sides of concrete foundation, footing, bases of columns, rafts, raft beam sides and soffits of foundation and plinth beam for flat rough finished concrete surfaces complete all as specified and directed.

Use and waste for formwork to sides of pillars, posts, struts, pier column for flat rough finished concrete surfaces complete all as specified and directed.

Use and waste for formwork to faces of walls, abutments, parapets etc complete all as specified and directed.

Use and waste for formwork to chajjas including edges for flat rough finished concrete surfaces complete all as specified and directed.

Use and waste for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for flat rough finished concrete surfaces complete all as specified and directed.

Use and waste for formwork to sides and soffits of domes, shell roof etc of curved surfaces complete all as specified and directed.

Use and waste for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for flat fair finished concrete surfaces complete all as specified and directed.

S&F for mild steel TMT bars, 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

S&F for mild steel TMT bars, 5 mm and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for hard core of broken stone of gauge not exceeding 63 mm, deposited, spread & levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

M&L for red bajri/ moorum filling including spreading, levelling, watering & well ramming, in layers not exc 15 cm each complete all as specified and directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (area of the sub structure in contact with backfill shall be measured) complete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

M&L for 100 mm thick plain cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in sub base for floor, finished even and rough complete all as specified and directed.

M&L for 40 mm thick plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in flooring, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 25 mm thick plain cement concrete 1:2:4, type B-1 (using 20mm graded aggregate) as in levelling course in floors, finished even and fair complete all as specified and directed.

M&L for brickwork with fly ash modular bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on any face of brick work or concrete surfaces mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement complete all as specified and directed. (Note: Water proofing compound shall be measured and paid seperately)

M&L for 10 mm thick rendering in cement mortar 1:6 on any face of brick work or conrete surfaces/stone masonary, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound ISI marked complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of oil bound distemper over a coat of cement based putty for smooth finish complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying two coats of cement base paint of any shade complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls and applying / finishing walls with premium acrylic smooth exterior paint with silicone additives of required shade: New work with two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified and directed.

S&F of 125x60mm size pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc; and fixed complete all as specified and directed.

S&F of 35mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and fixed to chowkhats complete all as specified and directed.

S&F of 30mm thick factory made 2nd class hardwood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F of factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F of solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

S&F of aluminium alloy, anodized sliding door bolt of 250 mm length with hasp and staple and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolt of extruded section or cast aluminium alloy complete all as specified and directed.

S&F of butt hinges, medium weight, mild steel of 100mm size and fixed with screws complete all as specified.

S&F of 100 mm long butt hinges,extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed type B-21 and fixed with screws complete all as specified.

S&F of aluminum handles cast type, anodized of 150 mm size and fixed with screws complete all as specified and directed.

S&F aluminum anodised barrel tower bolt of 150 mm size, extruded section and fixed with screws complete all as specified and directed.

S&F of anodised aluminium powder coated sections (minimum thickness of powder coating 50 micron) as in doors, windows, ventilators, partitions, shutters and frames with or without sash bars including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, necessary fittings etc. complete all as specified and directed.

S&F of 4.8 mm thick frosted glass and fixed to doors, windows etc. complete all as specified and directed

M&L for 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection, finishing the surface even and smooth without using extra cement laid in bays n exc 2 m in length and joints filled with bitumen mastic 1:3 complete all as specified and directed.

S&F of galvanised cold rolled steel section framed work size 600x600mm grid size 24x38x0.60mm tee (bottom precoated) and 24x24x0.50mm thick wall angle galvanised cold rolled steel section including expansions fasteners as in ceiling as per site requirement complete all as specified and directed. (Make : Gabson or equivalent as approved by GE)

S&F of 12mm thick gypsum board of size 600x600mm fixed to frame work of galvanised cold rolled steel as in ceiling with and including applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

S&F of asbestos free calcium silicate board of size 600 x 600 x 4 mm thick decorative type fire resistant, moisture resistant and tested as per IS 14862-2000 fixed to steel frame work as in ceiling, with and including applying two coats of oil bound distemper over a coat of primer complete all as specified and directed.

Returning, filling in any type of soil including spreading, levelling, watering and well ramming in layers n. exc 25 cm complete all as specified and directed.

Removing surplus soil obtained from excavation to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed.

S&F of vitreous china squatting pan of Orissa pattern 580x440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including all making connection and making good to the floor complete all as specified and directed.

S&F of syphonic action type PVC low level flushing cistern of 10 ltrs capacity incl flush pipe and fixing to supply pipe including PVC connection 15 mm bore and 600 mm long with brass heads & washers with making connections complete all as specified and directed.

S&F 15 mm bore bib taps, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferulle and fixed complete all as specified and directed.

S&F 15 mm bore stop cock, cast copper alloy, chromium plated with long shank and cut (concealed type), screwed down, screwed for iron pipe or union and fixed complete as specified and directed.

S&F 15 mm bore stop angle cock, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or union and fixed complete as specified and directed.

S&F of wash basins, vitreous china (flat back or angle back type) of 630 x 450 mm size including cutting for and pinning in ends of brackets or erecting stand/supported on wall, fixed with and including waste pipe, waste coupling, 15 mm dia pillar taps cast copper alloy with capstan head chromium plated with long screwed shanks and fly-nuts, screwed for iron pipe 15 mm bore and fixed complete all as specified and directed.

S&F of PVC connection 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F of brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges and fixed complete all as specified and directed.

S&F of 100 mm dia CP grating and fixed complete all as specified and directed.

S&F of stainless steel soap dish, any type, fixed with plugs with CP brass screws and fixed complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed in walls/ laid in trenches/floors complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed in walls / laid in trenches/floors complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) junction single (Single T), equal or unequal and fixed with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) junction single (Double T), equal or unequal and fixed with solvent cement complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) junction single (Single T), equal or unequal and fixed with solvent cement complete all as specified and directed.

S&F of PVC (SWR) bends any radius 110 mm dia and fixed with solvent cement complete all as specified and directed.

S&F of PVC (SWR) bends any radius 75 mm dia and fixed with solvent cement complete all as specified and directed.

S&F of 75mm dia PVC (SWR) floor/nahani trap with CP brass grating including jointing with solvent cement complete all as specified and directed.

S&F of PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F of 110 mm bore PVC (SWR) vent cowl and fixed complete all as specified and directed.

S&F of 75 mm bore PVC (SWR) vent cowl and fixed complete all as specified and directed.

S&F for chromium plated shower rose 125 mm with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors over and including 15mm thick screed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed

M&L for non skid ceramic coloured tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in floors over and including 15mm thick screed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and directed

M&L for glazed ceramic coloured tiles in vertical surface such as dado, riser, skirting etc. of size 350x 250x 7mm/ 450x 300x 7mm thick, over and including 10mm thick rendering 1:4 and set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

M&L for granite stone work (any type) 18 to 20 mm thick (table rubbed and polished) as in steps, jambs, pillars, window cills, cooking platforms, counter, shelves and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F of 1000 Ltrs capacity rotational moulded polyethylene water stotage tanks, triple layer (cylinderical verticle with closed top) hoisted & fixed in position as specified in SSR Pt-I including 20mm bore brass ball valve complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) as in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, coping, kneelers, apex stones, bed plates, kerbs and the like including weathering, slightly rounded or chemfered angle and throating complete all as specified and directed.

M&L for providing precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in cover slabs (for manholes etc), shelves and similar articles with plain faces including necessary moulds and set in cement mortar 1:4 complete all as specified and directed. (Note:-Reinforcement to be measured separately)

S&F of mild steel TMT bars 6 to 8 mm dia bars, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

Cutting into existing manholes/septic tanks for connecting new drains, making good to pipes and rendering, cutting out existing benching for forming branch channel (1/2 round or 3/4 section ) in cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) smooth finished, and reforming benching as required of 150 mm dia pipe complete all as specified and directed.

Taking up or down steel tubing and connections complete all as specified and directed for folowing bores:-

(a) 15 mm bore.

(b) 20 mm bore.

S&F of GI tubing medium grade with all necessary fittings and fixed to wall and ceiling or laid in floors complete all as specified and directed of following sizes:-

(a) 15 mm bore.

(b) 20 mm bore.

(c) 25 mm bore.

(d) 40 mm bore.

(e) 50 mm bore.

S&F of gun metal glove or gate valve, conforming to IS: 778 with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed of following sizes:-

(a) 15 mm bore.

(b) 20 mm bore.

(c) 25 mm bore.

(d) 40 mm bore.

(e) 50 mm bore.

M&L for clean dry sand cusion/ covering for protection of underground cables in trenches /filling under floors complete all as specified and directed.

M&L for sub class 'B' bricks locally available of best quality laid dry in trenches for cable protection complete all as specified and directed.

Excavation in post holes in any type of soil (or similar holes) each n exc 0.5 cum and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, incl removing of surplus soil complete all as specified and directed.

S&F of steel tubular mild steel work as in rafter, purlins, trusses, posts and like including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS.1161-1979 grade St.-240 complete all as specified and directed.

S&F of rolled mild steel work of steel sections as in rafter, purlins, trusses and like (beam, tee, angle, channel or flat sections (Fe 410-W(Gde E-250 quality) complete all as specified and directed.

S&F of mild steel work of angle iron, flat iron, plates etc as in wind ties for roof, brackets, cleats, fasteners, bases for posts and struts including all necessary drilling, bolting or riveting, etc. and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed.

M&L for preparation of new or previously untreated surfaces of steel and iron surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified and directed.

S&F of 0.50 mm thick pre- painted galvalume aluminum zinc coating GI based corrugated steel sheeting of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, chajjas and fixed with self tapping screws complete all as specified and directed

S&F of 0.50 mm thick pre- painted galvalume aluminum zinc coating GI based plain steel sheeting of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, chajjas and fixed with self tapping screws complete all as specified and directed.

S&F for stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed complete all as specified and directed.

S&F for mild steel framed work such as grills, gratings etc with ends of bars shouldered and/or riveted, framed guard bars, barred iron doors, ladders, framework of water tanks, and similar work confirming to Fe-290, Gde E-165 complete all as specified and directed.

Cutting holes into or through cement concrete slabs, chajjas, etc. reinforced or otherwise of superficial area exc 100 Sqcm but n exc 250 Sqcm and making good in CM 1:3 complete all as specified and directed.

Cutting channels, grooves or rebates n exc 15cm girth, and trimming surface for inserting steel sheet and making good in CM 1:3 complete all as specified and directed.

M&L for filleting in any position and to any shape in cement mortar 1:3 including all mitres, stops, etc. of sectional area exc 25 but n exc. 50 sqcm for fair finish exposed surfaces of walls complete all as specified and directed.

M&L for vitrified ceramic tile light shade 9-10 mm thick (square /rectangular) polished, area of each tile not exceeding 0.36 Sqm as in floors/skirting over and including 20mm thick screed bed in CM 1:6 etc and jointed in neat cement slurry and pointed in white or coloured cement to match the shades of tiles complete all as specified & directed.

M&L for plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in sub bases, foundations, mass concrete etc complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC, RCC or PVC), set in cement mortar and disposal of unservicable materials and rubbish to a distance not exceeding 100m complete all as specified and directed for the following bores:-

(a) 100mm bore

(b) 150mm bore

(c) 200mm bore

(d) 300mm bore

M&L for concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) complete all as specified and directed for the following bores:-

(a) 100mm bore

(b) 150mm bore

(c) 200mm bore

(d) 300mm bore

S&F of RCC NP2 drain pipes laid in trenches and jointed in cement mortar 1:3 and testing complete all as specified and directed for the following bores:-

(a) 100mm bore

(b) 150mm bore

(c) 200mm bore

(d) 300mm bore

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

S&F of 32mm dia PVC waste pipe 80cm long and fixed complete all as specified and directed.

Demolition of brick work, built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on any face of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:6 on any face of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Demolition of cement concrete reinforced (reinforcement cut as required to facilitate demolition) in any description and in any position not other wise specifically provided for complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block (Reflective type)in any shape and size confirming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed.

S&F of 200 mm bore cast iron sand cast soil, waste and vent pipes in any length with or without ears, with cement joints, fixed in walls/ laid in trenches/floors complete all as specified and directed.

Dismantling of wall and celing hard boards/AC sheets and plywood in any thickness & any position including cover fillets complete all as specified and directed.

S&F of 18/19mm thick prelaminated block board with one side decorative choice lamination & other side balancing white lamination, fixed with screws/nails to timber frame work complete all as specified and directed.

S&F of IInd class hard wood, plain fillets square, rectangular or triangular in section, clean sawn, secured with nails or brads; sectional area exc 13 sq cm and not exc 25 sq cm fillets complete all as specified and directed.

S&F of 30mm size stainlesss steel self closing hinges and fixed complete all as specified and directed.

S&F of 12mm thick external teak wood lipping for veneered particle board or block board fixed with nails complete all as specified and directed.

S&F of 100mm aluminium hasp and staple, safety type, anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed

S&F of 40mm dia cupboard/kitchen cabinet knobes, brass decorative type and fixed with nuts, screw and washer complete all as specified and directed.

Taking down chowkhats or frame n. exc 1.5 sqm each with shutters (without taking off shutters from the frame) complete all as specified and directed

S&F for 40mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides and both face covered with decorative face veneer 0.9 to 1 mm thick with lipping/ frame to match complete all as specified and directed.

S&F of 150 mm long stainless steel handles, ISI marked, cast type and fixed complete all as specified and directed.

S&F of 150 mm long stainless steel tower bolts, ISI marked, extruded section and fixed complete all as specified and directed.

S&F of 100 mm long stainless steel butt hinges, ISI marked, heavy duty and fixed complete all as specified and directed.

S&F of 300 mm long stainless steel sliding door bolts with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections ISI marked complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar complete all as specified and directed.

S&F of vitreous china oval shaped counter top wash basin, white of approx size 550x400mm including PVC flexible waste pipe, brass waste coupling 32mm bore, PVC pipe connection of 15mm dia & 600mm long complete all as specified and directed.

M&L for machine cut cut kota stone slab as in flooring, 18-20 mm thick over and including 20mm thick cement screed bed in CM 1:6; laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing complete all as specified and directed.

M&L for machine cut cut kota stone slab, 18-20 mm thick as in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4; laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing complete all as specified and directed.

M&L for providing and fixing fixed louvers fabricated from roll formed sections made of galvanized steel colour coated/powder coated (base steel as per IS 513 ‘D’ quality, galvanized as per IS: 277 with zinc of 120 grams/Sqm) with thickness of 0.58mm coated sections to be epoxy primered of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer of 5-7 microns or powder coated with pure polyester powder up to 50-60 microns thick, section for external frame 33x58 mm, glass holding flanges made of polypropylene, sections are to be cut to length, mitre joined with corner bracket, frames should be fixed to the concrete/masonry walls by means of self expanding screws complete all as specified and directed.

Taking down cement plaster on brick or concrete surfaces including wall tiling if any, racking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for preparation of plastered surfaces on walls and applying Heritage/ texture finish of approved design and shade over a coat of wall primer complete all as specfied and directed. Note: Each stage i.e. preparation of surfaces, application of primer, application of first coat & second coat will be got passed.

M&L for applying 2 mm thick white wall care putty on walls, finished even and smooth complete all as specified and directed.

S&F of 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc .50 sqm in each panels complete all as specified and directed.

M&L for providing precast cement concrete 1:2:4, type B-0 (using 12.5mm aggregate) jallies, 25mm thick (measured solid) including all mouldings but excluding frame etc. and set in cement mortar 1:4 complete all as specified and directed.

S&F in repairs 25mm dia stainless steel drapery rod type including fancy type brackets (02 Nos) of approved quality complete all as specified and directed.

S&F in replacement sinks with drainage board made of stainless steel 1mm thick kitchen with plugs, washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm including PVC waste coupling and pipe complete all as specified and directed.

S&F of 15 mm pillar taps, fancy type, cast copper alloy, chromium plated, screwed down high pressure, with or without lettered "Hot or Cold" with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

M&L for concealed/surface point wiring for one light point with 1.50 sqmm (nominal area), FRLS PVC insulated, unsheathed, single core multi-stranded copper conductor cable, 1100 volts grade, ISI marked controlled by one one-way switch, drawn through and including concealed medium grade PVC conduit not less than 20 mm dia, ISI marked, with all accessories / PVC casing and caping of size 25 mm, ISI marked with complete accessories to be used wherever wiring to be run on ceilings and concrete surfaces) including one run of 1.5 sqmm FRLS muti stranded copper conductor (Green colour cable) as earth continuity wire connected to common earth dolly including sunk sheet steel terminal box made out of 1.20 mm thick and not less than 60 mm in depth GI/MS/ prssed steel terminal box to be conclead in wall, duly painted with two coats of anti corrosive black bituminous paint over a coat of red oxide primer in and out sides and two coated of aluminium paint on internal surface , including laminated hylum sheet cover, ISI marked of hylem sheet for mounting of fittings like switches, sockets, fan regulators etc. fixed with galvanised screws and cup washers complete all as specified and directed. Note: Rate includes chase cutting for concealed wiring.

All as per item No. 144.00 here-in-before but for 3 pin socket outlet, 5 Amp on the same board with other switches.

All as per item No. 144.00 here-in-before but for exhaust fan point controlled by one push button on same board with other switches.

All as per item No. 144.00 here-in-before but for 3 pin socket outlet, 5 Amp on the independent board.

M&L for sub main wiring with two single core FRLS PVC insulated unsheathed cable 1100 volts grade, multistranded copper conductor cable of 4.0 Sqmm drawn in and including non metallic rigid PVC conduit of 25 mm dia, ISI marked including one run of FRLS PVC insulated unsheathed, multistranded copper conductor cable of 4.0 Sqmm (Green colour) as earth continuity conductor cable connected to earth dolly complete all as specified and directed. Note: Three runs of cable shall be measured as a single length.

S&F of switch piano flush type single pole one way 5 Amps complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 pin flush type 5 Amp complete all as specified and directed.

S&F of ceiling rose surface bakelite 65mmm dia, three terminal complete all as specified and directed.

S&F of lamp holder, PVC/polycorbonate type with back plate with and including LED bulb retrofit type 9/10 watts complete all as specified and directed.

S&F of 1200mm sweep ceiling fans complete with blades, down rods, electronic remote, steep type and accessories, 165V -285V, minimum air delivery 224 CMM with service value 6.00 BEE, five star rated with brushless direct current motor (BLDC) with hook for hanging ceiling fan complete all as specified and directed. Make: Atomberg Studio or equivalent in Bajaj/ Havells / Crompton.

S&F of LED light fitting 1 x 20 watts, 220 volt, AC, decorative box type with driver, holder including LED tube light and connecting with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make: Bajaj Cat part No. 8304143 or equivalent in Orient/ Cromptom

S&F of 300mm sweep exhaust fan, steel body, AC single phase, 140-285 Volts with blades, frame and louvers including connecting with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. Make: Bajaj/ Orient/ Cromptom

M&L for earthing with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground (earth pit not less level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth wire of 4 mm as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3, SSR including excavation of earth pit in any soil, charcoal dust, common salt 15 mm all around earth plate, PCC M-15 (nominal mix) as in pit and cover, water pipe funnel and GI protection pipe light grade 15mm dia upto panel connecting earth lead to panel complete all as specified and directed. Note : Earth continuity conductor including protection pipe up to 7.5 mtrs from earth electrode will be included in unit rate.

S&F of sheet metal enclosure for MCB SPN DB, 200 Amps rated busbar, 8 way, double door enclosure made up of CRCA steel sheet, RAL 9003 powder coated, IP-43 with MCB as incommer and MCB SP/TP in outgoing complete all as specified and directed.

S&F of MCB, SP, 6 to 32 Amps, 240 volts, 10 KA breaking capacity, 'C' curve including connection with suitable size copper lugs complete all as specified and directed.

Supply and laying XLPE insulated, PVC sheathed, armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 10 sq. mm, 2 core, laid in trenches or in floors of fixed to wall/pole and testing complete all as specified and directed.

M&L for GI Tubes, 'light grade' galvanised, with all fitting and laid in floors, under road, pavement or hard standing steel water tubing bore of tube 25 mm.

S&F of openwell submersible pump of capacity 3 HP/2.2 KW, 440 Volts, 50 Hz, maximum working pressure 2.7 kg/Sqcm, suitable for three phase supply motor speed of 2900 RPM , suc x del of size 65 mmx50mm including starter, all lugs, fittings and testing after completion complete all specified and directed. Make: Havells model No. WR3T or equivalent in CG/ Kirlosker.

Supply & filling / laying in layers graded filter media comprising for recharge arragement of borewell complete all as specified and directed of following mesh graded media:-

(a) Graded coarse sand of size 1.5mm to 1.1 mm size

(b) Fine sand of 34 to 33mm mesh

(c) Natural pebbles of size 25mm to 50mm

(d) Natural pebbles of size 12mm to 25mm

(e) Natural pebbles of size 6mm to 12mm

(f) Natural pebbles of size 3mm to 5mm

S&F of FRLS PVC insulated, unsheathed, single core multi-stranded copper conductor cable, 1100 volts grade, of size 2.5 sqmm 3 core, 220 Volts, 50 Hz including copper lugs complete all as specified and directed.

Supply, laying, fixing or passing through pipe, XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm, 4 core in service connections complete all as specified and directed.

M&L for earthing complete with galvanised steel plate earth electrode 600 x 600 x 6 mm thick, burried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 meters below normal ground level, connected to earthing lead of 32 x 6 mm galvanised mild steel strip by means of bolts, nuts, check nuts and washers from earth plate to test point upto 7.5 meter including necessary concrete chamber in cement concrete M-15 (nominal mix), precast RCC cover slab in cement concerete M15 (Normal Mix) of size 40 x 40 x 5 cm duly reinforced with 8 mm dia TMT bars @ 150 mm C/C both ways with one handle for lifting, GI funnel, GI wire mesh filter, 20 mm dia GI pipe medium grade for watering, 40 mm dia GI Pipe medium grade for protection of earthing lead, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil/strate and testing complete all as specified and directed.

S&F of electromagnetic water meter digital type with RS 485 protocol with latest IS specification such as EMFM-DN-50-R-MS-SS316 - IP 67-0.05%, application media - normal water, rubber liner , elecrodes SS 316 L, 50 mm flanged end connection, 20 - 60 bars pressure, integerated display, 24 Volts DC/ 220 Volts AC power supply, signal O/P- pulse, 4-20 ma, RS 485 modbus, accuracy +- 0.5%, flow type - SS 304, housing - MS seat, electronic housing - die cast aluminium, electromagnetic water meter digital type of suitable for 250mm cast iron line including all necessary connected fitting/fixture & dash board, GPRS system including taking out old meter complete all specified and directed.

S&F of cast iron SVE Y type strainer, size 50 mm, flanged ends including nuts, bolts and rubber gaskets complete all as specfied and directed.

Deduct Schedule of credit (calculation will be done off line) Rs. 30505.00

NDS TRADERS

JYOTI ENTERPRISES

ROYAL CONSTRUCTION

R K Sales