REPAIR AND REPLACMENT OF SUBMERSIBLE,CENTRIFUGAL JET AND VT PUMP SETS AND CONTROL PANELS WITH ALLIED WORKS UNDER GE SAUGOR

Amount

M&L for taking out submersible pumpset any size and any capacity from open well / bore well by disconnecting submersible cable connection and delivery pipe line using tripoid chain pulley or any other means, dismantling from GI pipe, opening pump set and carrying for repairs connecting back to MS/GI pipe and lowering the submersible pumpset of capacity upto 5 HP alongwith cable into open well / bore well in original position after repairs complete all as specified and as directed. Note:- (a) Unit rate quoted shall deemed to be included for labour only for taking up & lowering the submersible pump from bore well along with delivery pipe. (b) Repairs / rewinding & servicing of submersible pump shall be measured & paid under relevant items. (c) Spares parts required shall be measured under Srl item No.18 here-in-after.

All as Srl item No.1.00 above but 5 HP to 7.50 HP capacity

All as Srl item No.1.00 above but 9 HP to 10 HP capacity

All as Srl item No.1.00 above but 15 HP to 20 HP capacity

All as Srl item No.1.00 above but 30 HP to 40 HP capacity

M&L for opening up vertical /open well submersible motor (Single Phase/Three Phase) up to 1.0 HP capacity, taking out burnt out winding, cleaning the slots with CTC and rewinding the same with new PVC insulated copper winding wire of existing gauge and turns, assembling back into position by using new suitable studs etc., oiling and greasing and fixing back into position for making motor fully functional, applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer, testing for satisfactory running complete all as specified and directed by the Engineer-in-charge NOTE : (i). The spare parts to be replaced shall be measured and paid under Srl item No.18 here-in-after (ii). Lowering and lifting charges shall be measured and paid separately

All as per Srl item No. 6 here-in-before but 3 HP

All as per Srl item No. 6 here-in-before but 5/6 HP

All as per Srl item No. 6 here-in-before but 7.5/9/10 HP

All as per Srl item No. 6 here-in-before but 15/20 HP

All as per Srl item No. 6 here-in-before but 30/40 HP

M&L for opening submersible pump set up to 1.0 HP Motor capacity , carrying out repairs, reconditioning of spare parts such as impellers, thrust bearing with plate, shaft etc., by metalling and machining to their original shape and size, assembling back into position by using new suitable gland/rubber packing including studs, flanges, bolts and nuts etc., oiling and greasing for making pumpset fully functional, applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer, testing for satisfactory running complete all as specified and directed by the Engineer in charge NOTE : The spare parts to be replaced will be measured and paid separately under Srl item No.18 here-in-after

All as per Srl item No. 12 here-in-before but 3 HP

All as per Srl item No. 12 here-in-before but 5/6 HP

All as per Srl item No. 12 here-in-before but 7.5/9/10 HP

All as per Srl item No. 12 here-in-before but 15/20 HP

All as per Srl item No. 12 here-in-before but 30/40 HP

Supply only following items complete all as directed:-

SS Shaft with Key Suitable for Submersible pump set 1 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 3 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 5/6 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 7.5/9/10.0 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 15/20 HP Capacity

SS Shaft with Key Suitable for Submersible pump set 30/40 HP Capacity

Impeller made out bronze suitable for 1 HP Capacity Submersible pump

All as per Srl item No. 18.07 here-in-before but 3 HP Capacity

All as per Srl item No. 18.07 here-in-before but 5/6 HP Capacity

All as per Srl item No. 18.07 here-in-before but 7.5/9/10 HP Capacity

All as per Srl item No. 18.07 here-in-before but 15/20 HP Capacity

All as per Srl item No. 18.07 here-in-before but 30/40 HP Capacity

Pump bush lower and upper alongwith sleeves made out bronze as per the sample suitable for 1 HP Capacity Submersible pump set

All as per Srl item No. 18.13 here-in-before but 3 HP Capacity

All as per Srl item No. 18.13 here-in-before but 5/6 HP Capacity

All as per Srl item No. 18.13 here-in-before but 7.5/9/10 HP Capacity

All as per Srl item No. 18.13 here-in-before but 15/20 HP Capacity

All as per Srl item No. 18.13 here-in-before but 30/40 HP Capacity

M&L for opening the induction motor of capacity upto 1.0 HP, taking out damaged/burnt out winding from single phase /three phase motor, cleaning the slots with CTC and rewinding the same with new super enamelled copper winding wire of existing gauge and turns, oiling and greasing and fixing back into position for making motor fully functional applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer and testing for satisfactory running complete all as specified and directed (Note:- The spare parts to be replaced shall be measured and paid separately under Srl item No.36 here-in-after)

All as per Srl item No. 19 here-in-before but 3 HP

All as per Srl item No. 19 here-in-beforebut 5/6 HP

All as per Srl item No. 19 here-in-before but 7.5/9/10 HP

All as per Srl item No. 19 here-in-before but 15/20 HP

All as per Srl item No. 19 here-in-before but 30 HP

All as per Srl item No. 19 here-in-before but 40/50HP

All as per Srl item No. 19 here-in-before but 220 HP

All as per Srl item No. 19 here-in-before but 240/260HP

M&L for dismantling centrifugal/monoblock pumpset of capacity upto 1.0 HP Motor, carrying out repairs, replacement of worn out parts such as impellers, bearings, gland metal bushes etc., and reconditioning of spare parts such as shaft, impellers, housing body, bearing gland plate etc., by metalling and machining to their original shape and size and assembling back into position by using new suitable gland dory, gland plate, gland/rubber packing including studs/gland bolts and nuts, coupling bushes etc., oiling and greasing for making pumpset fully functional applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer and testing complete all as specified and directed (Note:- The spare parts to be replaced shall be measured and paid separately under Srl item No.36 here-in-after):-

All as per Srl item No. 28 here-in-before but 3 HP

All as per Srl item No. 28 here-in-before but 5/6 HP

All as per Srl item No. 28 here-in-before but 7.5/9/10 HP

All as per Srl item No. 28 here-in-before but 15/20 HP

All as per Srl item No. 28 here-in-before but 30 HP

All as per Srl item No. 28 here-in-before but 40/50HP

All as per Srl item No. 28 here-in-before but 220 /240/260 HP

Supply only following items complete all as directed:-

NDE/DE Ball bearing suitable for upto 1 HP Capacity motor Make:-TATA/SKF

All as per Srl item No. 36.01 here-in-before but suitable for 2/3 HP Capacity motor Make:-TATA/SKF

All as per Srl item No. 36.01 here-in-before but suitable for 5 HP Capacity motor Make:-TATA/SKF

All as per Srl item No. 36.01 here-in-before but suitable for 7.5/9/10 HP Capacity Make:-TATA/SKF motor

All as per Srl item No. 36.01 here-in-before but suitable for 12.5/15 HP Capacity motor Make:-TATA/SKF

All as per Srl item No. 36.01 here-in-before but suitable for 30 HP Capacity motor Make:-TATA/SKF

All as per Srl item No. 36.01 here-in-before but suitable for 40/50 HP Capacity motor Make:-TATA/SKF

All as per Srl item No. 36.01 here-in-before but suitable for 220 HP Capacity motor Make:-TATA/SKF

All as per Srl item No. 36.01 here-in-before but suitable for 240/260 HP Capacity motor Make:-TATA/SKF

SS Shaft suitable for centrifugal pump upto 1.0 HP HP Capacity

All as per Srl item No. 36.10 here-in-before but 2/3 HP Capacity Pump set

All as per Srl item No. 36.10 here-in-before but 5 HP Capacity Pump set

All as per Srl item No. 36.10 here-in-before but 7.5/9/10 HP Capacity Pump set

All as per Srl item No. 36.10 here-in-before but 12.5/15 HP Capacity Pump set

All as per Srl item No. 36.10 here-in-before but 30 HP Capacity Pump set

All as per Srl item No. 36.10 here-in-before but 40/50 HP Capacity Pump set

All as per Srl item No. 36.10 here-in-before but 220 HP Capacity Pump set

All as per Srl item No. 36.10 here-in-before but 240/260 HP Capacity Pump set

Gunmetal thrust bearings suitable for upto 1.0 HP Pump set

All as per Srl item No. 36.19 here-in-before but 2/3 HP Capacity Pump set

All as per Srl item No. 36.19 here-in-before but 5 HP Capacity Pump set

All as per Srl item No. 36.19 here-in-before but 7.5/9/10 HP Capacity Pump set

All as per Srl item No. 36.19 here-in-before but 12.5/15 HP Capacity Pump set

All as per Srl item No. 36.19 here-in-before but 30 HP Capacity Pump set

All as per Srl item No. 36.19 here-in-before but 40/50 HP Capacity Pump set

All as per Srl item No. 36.19 here-in-before but 220 HP Capacity Pump set

All as per Srl item No. 36.19 here-in-before but 240/260 HP Capacity Pump set

CI Impeller suitable for upto 1.0 HP Motor

All as per Srl item No. 36.28 here-in-before but 2/3 HP Capacity Pump set

All as per Srl item No. 36.28 here-in-before but 5 HP Capacity Pump set

All as per Srl item No. 36.28 here-in-before but 7.5/9/10 HP Capacity Pump set

All as per Srl item No. 36.28 here-in-before but 12.5/15 HP Capacity Pump set

All as per Srl item No. 36.28 here-in-before but 30 HP Capacity Pump set

All as per Srl item No. 36.28 here-in-before but 40/50 HP Capacity Pump set

All as per Srl item No. 36.28 here-in-before but 220 HP Capacity Pump set

All as per Srl item No. 36.28 here-in-before but 240/260 HP Capacity Pump set

Glandflange along with stud bolt & nut wity washer suitable for 2/3 HP Capacity motor pump set

All as per Srl item No. 36.37 here-in-before but 5 HP Capacity Pump set

All as per Srl item No. 36.37 here-in-before but 7.5/9/10 HP Capacity Pump set

All as per Srl item No. 36.37 here-in-before but 12.5/15 HP Capacity Pump set

All as per Srl item No. 36.37 here-in-before but 30 HP Capacity Pump set

All as per Srl item No. 36.37 here-in-before but 40/50 HP Capacity Pump set

All as per Srl item No. 36.37 here-in-before but 220 HP Capacity Pump set

All as per Srl item No. 36.37 here-in-before but 240/260 HP Capacity Pump set

Love joy rubber coupling (Star rubber coupling) suitable for 5 HP motor pumset

All as per Srl item No. 36.45 here-in-before but 7.5/9/10 HP Capacity Pump set

All as per Srl item No. 36.45 here-in-before but 12.5/15 HP Capacity Pump set

All as per Srl item No. 36.45 here-in-before but 30 HP Capacity Pump set

All as per Srl item No. 36.45 here-in-before but 40/50 HP Capacity Pump set

All as per Srl item No. 36.45 here-in-before but 220 HP Capacity Pump set

All as per Srl item No. 36.45 here-in-before but 240/260 HP Capacity Pump set

Metal coupling split type along with Key suitable for 5 HP Motor pump set

All as per Srl item No. 36.52 here-in-before but 7.5/9/10 HP Capacity Pump set

All as per Srl item No. 36.52 here-in-before but 12.5/15 HP Capacity Pump set

All as per Srl item No. 36.52 here-in-before but 30 HP Capacity Pump set

All as per Srl item No. 36.52 here-in-before but 40/50 HP Capacity Pump set

All as per Srl item No. 36.52 here-in-before but 220 HP Capacity Pump set

All as per Srl item No. 36.52 here-in-before but 240/260 HP Capacity Pump set

Slip ring assy complete with studs made out of copper as sample suitable for 260 HP Capacity Motor

Carbon bush holder made of bronze as sample suitable for 260 HP Capacity Motor

Carbon brushes holder made of bronze as per existing sizes per sample suitable for 260 HP Capacity Motor

Taking down VT pump set of capacity 135/150 HP from Chittora pump house from Jack well and dismantling the after disconnection the holo shaft motor from the pump set and suction line with connected items line shaft of turbine pump set items such as impellers,bushes ,spider assembly etc and reassembling after necessory repair grinding/lathe work / replacement the following items paid separetaly here as after,testing complete and fixing at the site.including transportation. Note : (i) Replacement of defective part only shall be replaced if required shall be measured & paid separately under Srl item No.38 here-in-after (ii) Labour element is included in the rate and make of part shall be existing (iii) Shifting of parts/motor/pump for repair grinding/lathe work / replacement from Pump house to Wksp for and back rate is included. (iv) Applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer

Supply only following items complete all as directed:-

Impeller made out of MS with impeller key complete all as directed

Supply only the impeller shaft coupling complete all as directed

Bush of top impeller made out of steel with impeller keycomplete all as directed

Line shaft and replacement of the Line shaft coupling complete all as directed

Sleeves made out of bronze complete all as directed

Spider assy with bearing holder flanged complete all as directed

Stud bolt with washer complete all as directed

Bearing NU-318C complete all as directed

Bearing 6316 complete all as directed

Bush made out of bronze complete all as directed

Rubber bush complete all as directed

Taking down the Holo shaft slip ring induction motor of capacity 135/150 HP from VT Pump and Dismantling carbon bush holder, carbon bush and slip ring assy with connected items and rewinding with original guage of copper winding wire insulation material and terminal plate and copper sturds and reasssemble & testing proper aligment after necessory repair and repair/replacement of the following items paid separately here as after and re-assembling at jack well chittora pump house .Including transporation from chittora pump house to work shop and back. Note : (i) Replacement of defective part only shall be replaced if required shall be measured & paid separately under Srl item No.40 here-in-after (ii) Labour element is included in the rate and Make of part shall be existing (iii). Applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer

Supply only following items complete all as directed:-

Slip ring assy complete with studs made out of copper as per existing sample

Carbon brushes holder made of bronze as per existing sizes as per sample

Carbon brushes as per existing size and as per sample

Taking down Mud pump set set of capacity 25HP from chittora pump house from Jack well and Dismantling the after disconnection the holo shaft motor from the pump set and suction line with connected items line shaft of turbine pump set items such as impellers,bushes ,spider assembly etc and reassembling after necessory repair grinding/lathe work / replacement the following items paid separetaly here as after,testing complete and fixing at the site.including transportation. Note : (i) Replacement of defective part only shall be replaced if required shall be measured & paid separately under Srl item No.42 here-in-after (ii) Labour element is included in the rate and make of part shall be existing) (iii) Shifting of parts/motor/pump for repair grinding/lathe work / replacement from Pump house to Wksp for and back rate is included. (iii). Applying two coats of synthetic enamel paint over a coat of red oxide zinc Chrome primer

Supply only following items complete all as directed:-

Impeller made out of bronze with impeller key complete all as directed

Bowl bearing of top impeller made out of bronze with impeller key. complete all as directed

Impeller shaft coupling complete all as directed

Line shaft and replacement of the Line shaft coupling complete all as directed

Sleeves made out of bronze complete all as directed

Spider assy with bearing holder flanged complete all as directed

Stud with nut complete all as directed

Bearing complete all as directed

Oil scement set of 08 complete all as directed

Bearing complete all as directed

Bush made out of bronze complete all as directed

Rubber bush complete all as directed

Taking down the mud pump motor of capacity 25 HP from Mud Pump and Dismantling the incoming electrical /Pump connection assy with connected items and rewinding with original gauge of copper winding wire insulation material and terminal plate and copper sturds and reasssemble & testing proper aligment applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primerafter necessory testing and commissioning complete all as specified and directed by Engineer-in-Charge

M&L for development of tube well with compressed air by means of air compressor of suitable capacity not less than 200 cum/Hrs and over pumping using suitable capacity pump to make available water sand free, silt free, turbidity and constant flow until sand free water is received complete all as specified and directed at site requirement.

Taking out the existing DOL starter, 415V, 3 Ph, 50 Hz from panel suitable for up to 5 HP Capacity motor , cleaning the electronic parts from inside, refixing the OLR, Contactor, NVC and SPP etc of the following capacity motor complete all as specified and directed by the Engineer-in-charge NOTE : Quoted rate deemed to include to replacement of spares and making serviceable condition

All as per Srl item No. 45 here-in-before for suitable for 7.5 HP Motor

Taking out the existing Star-delta starter suitable for 10 HP Capacity motor from panel, cleaning the electrnic parts from inside, refixing the OLR, Contactor, NVC,and SPP connecting link wires etc of the following capacity motor complete all as specified and directed by the Engineer-in-charge Note : Quoted rate deemed to include to replacement of spares and making serviceable condition

All as per Srl item No. 47 here-in-before for suitable for 12.5 HP Motor

All as per Srl item No. 47 here-in-before for suitable for 15/20 HP Motor

All as per Srl item No. 47 here-in-before for suitable for 30/40 HP Motor

All as per Srl item No. 47 here-in-before for suitable for 50 HP Motor

All as per Srl item No. 47 here-in-before for suitable for 220 HP Motor

All as per Srl item No. 47 here-in-before for suitable for 240 HP Motor

S&F in replacement DOL Starter415V, 50Hz, 3 Phase suitable for Upto to 7.5HP Motor, including replacement of copper lugs as per suitable and making suitable mounting on wall/floor stand with angle bolt,nut with wahsers as per size all as specified and directed by Engineer-in-Charge

S&F in replacement Star delta starter 415V, 50Hz, 3 Phase suitable for 10/12.5 HP Motor, including replacement of copper lugs as per suitable and making suitable mounting on wall/floor stand with angle bolt,nut with wahsers as per size all as specified and directed by Engineer-in-Charge

All as per Srl item No. 55.00 here-in-before but 15 HP Capacity Motor

All as per Srl item No. 55.00 here-in-before but 20 HP Capacity Motor

All as per Srl item No. 55.00 here-in-before but 30 HP Capacity Motor

All as per Srl item No. 55.00 here-in-before but 40 HP Capacity Motor

All as per Srl item No. 55.00 here-in-before but 50 HP Capacity Motor

M&L for disconnecting cable connection from exiting Soft starter suitable for 240 HP Capacity motor at Berthuma Pump house, 415V, 3 Phase,50Hz and including replacement of such a spare parts of Bypass relay and contactor, Plate and stays, USB cable , current transformer, connection kit etc and making serviceable condition testing and commissioning complete all as specified and directed by Engineer -in-Charge. Note:- Quoted rate shall deemed to be included for replacement of spares and making serviceable condition.

M&L for disconnecting cable connection from exiting Soft starter suitable for 135/150 HP Capacity motor at Chittora Pump house, 415V, 3 Phase,50Hz and including replacement of such a spare parts of Bypass relay and contactor, Plate and stays, USB cable , current transformer, connection kit etc and making serviceable condition testing and commissioning complete all as specified and directed by Engineer -in-Charge. Note:- Quoted rate shall deemed to be included for replacement of spares and making serviceable conditon.

M&L for excavated soil up to 5cm root of the vegetation cutting removing completely by spade and surface dressing all around the all Pump House installation area to keep the installation area(external only) clean and tidy all as per specified and directed by Engineer -in-Charge. NOTE: All the installation shall be kept clean through out the contract period by repeatedly removing the grasses/trees/weads as many times as required depending on the growth of the grass.This item shall be measured and paid only once during entire CA period.

Taking down the wooden sleepers from the slots /opening of the anicut across the river Bewas at Chittora in the lean season and stacking them separately at Chittora pump house in the slots of Anicut for their serviceability after applying black oil to serviceable sleepers complete all as directed. Note:- Unserviceable sleepers shall be stacked properly at Chittora pump house in the slots of Anicut for inspection of the Engineer-in-Charge.

S&F second class hard wood (well seasoned) wooden sleeper of size 150mmx100 mm cross sectional size and not less than 1475 mm (59") long duly tapered at end for easy insertion in the slots complete with and incl 02 Nos eye hooks made out of MS plain round bar 20 mm dia 200 mm long for each hook and the dia of hook shall be 50 mm, the other end of the round bar shall be tapered and fixed with wooden sleeper including applying a coat of coal tar on entire surface of sleepers as directed by Engr-in-Charge.

Refixing of wooden sleepers, tide with & including 18 SWG GI wire to protect the wooden sleepers and fixed with wooden sleeper including applying a coat of coal tar on entire surface of sleepers, from washing out in heavy water current upto a level of 16 feet from bottom to anicut complete all as directed. Note:-Serviceable sleepers obtained fron Srl item No.64 above shall be re-used in this item.

M&L for black cotton/ yellow soil as required in water condition to fill the gap of two sleepers in the slots of the maximum height 16 feet to avoid the leakage/seepage of water entire contract period complete all as specified and directed . NOTE :(a) Contractor shall be responsible for filling of black cotton soil in between gap of two sleepers of the slot upto 16 feet height without any leakage as per directions of Engineer in Charge (b) Entire quantity of BC soil shall be delivered by Contractor before mansoon & will be stacked properly at a distance of 20 mtr away from river as per directions of Engr-in-Charge. (c) Rate deemed to include for providing safety belt / ladder, etc., as required at site.

M&L for opening the wooden sleepers upto 8 feet from Chittora anicut gate for release of water to Dhana and closing the anicut slots upto 16 feet as per direction of Engineer-in-Charge. Note (i) Rate deemed to include to filling the cotton soil upto 16 feet height without any leakeage (ii) Rate deemed to include for providing safety belt / ladder, etc., as required at site.

M&L for arresting water leakeage from slots in anicut gates upto 16 feet height to fill the cotton soil with out any leakeage as per direction of Engineer-in-Charge Note (i) Rate deemed to include to filling the cotton soil upto 16 feet height without any leakeage (ii) Rate deemed to include for providing safety belt / ladder, etc., as required at site.

Removing the silt/rubbish deposited on the other side of the anicut and depositing at a place not more than 50 mtrs and removing as directed by Engr-in-Charge. Note : The silt/rubbish shall be stacked properly for measurement purpose all as directed.

Cutting and removing the washed out deposit at anicut trees/tree branches during the monsoon and before closing the anicut. The trees /tree branches obtained from the river shall be weighed. The weighing of wood shall be contractors responsibility and no extra shall be payable to him on this account.

M&L for Cutting of vegetation,bushes grass etc surrounding the pump house,power house and OHT/ Sump area at various installations and removing to a distance of 50 mtr all as directed.

M&L for PCC 1:4:8, type B1 (using 20mm graded stone aggregates) as in filling and making good distrubed surface all as specified and directed by the Engineer-in-charge

Taking down the existing rusted/damaged motor pump frame from existing location and fabricated new MS frame as per size,thickness and applying two coats of synthetic enamel paint over a coat of red oxide Zinc chrome primer complete all as specified and directed by Engineer -in-Charge

M&L for painting of CI /GI pipe line with one coat of red oxide Zinc chrome primer and two coats of anti corrosive synthetic enamel paint including prearation of old painted surface complete all as specified and as directed . Note:-Inlet pipe should be painted in blue colour , out let pipe should be painted in green colour and over flow pipe with Yellow

shubhanshu traders

shivansh traders